Search Documents

By James W. Bass

Atmospheric fluidized bed combustion (AFBC) is an improvement in coal-fired boiler design that offers several advantages over conventional boilers. AFC can meet sulfur and nitrogen oxide emission regulations without the need for add-on flue gas treatment equipment. The relatively low combustion temperature inhibits ash melting, thus reducing slagging and fouling which can, in turn, increase a boiler's fuel flexibility. This report discusses, in general, AFBC technology and, in particular, progress at the 20-MW Pilot Plant built by the Tennessee Valley Authority (TVA) at its Shawnee Power Station near Paducah, Kentucky.

Jan 1, 1985

By Frank W. Schmechel

The subsidence monitoring program at the Old Ben No. 24 Mine was planned in 1976 as part of the on- going demonstration of longwall mining. The construction and installation of the network of surface subsidence monuments was started in Play of 1976 and completed four weeks later after which an initial reference survey was made of all surface monuments. Mining of the first longwall panel started in September of 1976 and was completed in May of 1977. Mining of the second panel started in August of 1977 and is continuing at this time. The Automatic Data Acquisition System (ADAS), which is the subject of this paper, was installed over the second panel on March 29, 1978 near the panel center (Figure 1) and approximately 104 meters (370 feet) in front of the face position at that time. Mine No. 24 is located approximately 5 kilometers (3 miles) Northwest of Benton, Franklin County, Illinois. Coal is being mined from the Illinois (Herrin) No. 6 seam which is at a depth of about 189 meters (620 feet) at the site. The Herrin No. 6 is up to 2.7 meters (9 feet) thick in the mine but a constant thickness of 2.1 meters (7 feet) is being mined by the demonstration longwall with both roof and floor coal being left for stability. Although the seam is flat laying at the mine, it dips north- ward regionally. Topographically, the surface over the demonstration panels is essentially flat and low laying with several areas of standing water. The Rend Lake Dam (United States Army Corps of Engineers) is about 305 meters (1000 feet) north of the demonstration site.

Jan 1, 1979

By D. S. Choi

Underground production of coal by longwall methods has increased significantly in the last few years and will very likely continue to: increase. There are several reasons for this. First, as mining moves into seams having greater overburden, roof exposure must be reduced since support will become' increasingly expensive. Secondly, the growing demand for coal has forced the coal industry to seek alternative, more productive, coal mining methods. In addition, the longwall method greatly simplifies the underground ventilation network. This paper addresses itself to the design of longwall development headings, particularly to those of the United States where multiple development headings are required by law. The most burdensome problem encountered in many longwall mining installations is deterioration of the tailgate due to the combined effect from, the active longwall gob and the old gob made by mining the previous panel.1 Portions of the tailgate entry are sometimes closed to such a degree that extensive repair work is necessary to keep the entry in usable condition. The purpose of this paper is to present the result of a study in progress which combines field measurements with numerical model analysis to reduce the cost of maintaining tailgate entries in longwall mining systems.

Jan 1, 1975

By K. Papke

Nine western states contain significant barite deposits, but most deposits are in Nevada, which has been the principal western producer for more than three decades. Nevada produces about 85% of the total United States production, but about one-half of the barite consumed in the country is imported. Approximately 95% of the barite is used in drilling muds. Sharply decreased oil and gas drilling, starting in early 1982, severely depressed the domestic barite industry. Other problems for western barite include long distances to the areas of major drilling, high railroad-freight rates, and increased barite imports. Bedded deposits, formed by submarine exhalative processes, account for almost all western production, and reserves are large.

Jan 1, 1983

By James R. Craig

The Central and Southern Appalachians were the major sources of gold in the United States throughout the first half of the 19th century and have continued to yield gold to the present day. Small amounts of gold were probably extracted by the Indians and the Spaniards but the first documented report of gold in the region was made by Thomas Jefferson who found a four pound lump of gold ore, which yielded 0.85 troy oz., in the Rappahannock River of Virginia in 1782. Gold was subsequently discovered in North Carolina between 1793 and 1799, in Virginia in 1806, in South Carolina in 1827, in Georgia in 1829 and in Alabama about 1830 (Becker, 1894-5; Pardee and Park, 1948). The gold belts of the Central and Southern Appalachian Piedmont and Blue Ridge Provinces are shown in Figure 1. The superimposed circles indicate the mount of production from some of the more productive and well known areas. Although North Carolina produced far more gold than the other states, the most significant concentrated area of production is the Dahlonega District in Georgia which yielded more than 500,000 troy ounces. After discovery, gold production increased rapidly as shown in Figure 2. Production was at its maximum between 1830 and 1852 with combined totals generally exceeding 30,000 troy ounces per year. Production dropped sharply after the California gold rush in 1849 as experienced miners moved westward in search of bigger and easier stakes. After the Civil War briefly halted gold mining in the Appalachians, production rose to an average of about 8,000 ounces per year from 1865 until 1878 and to an average of about 13,000 ounces per year from 1881 until 1915 when it again fell to near nil (Pardee and Park, 1948). Minor resurgences occurred in the 1930's and 1940's. Although there has been no reported production in recent years, it is likely that "weekend panners" still remove hundreds of ounces from streams annually. The total reported production for the area through 1959 is in excess of 2.5 million troy ounces.

Jan 1, 1981

By Stephen E. Kesler

Carbonaceous sedimentary rocks are abundant in the upper part of the caldera or maar that hosts the Puebio Viejo Au-Ag district, and much of the Moore sulfide zone is in these rocks. These rocks are thinly layered and contain scattered plant remains and variable amounts of volcaniclastic debris and pyrite. The carbonaceous matter in the sediments yields no X-ray diffraction pattern and is not graphite. It has C/N ratios of 4 to 10, and &13C values of about -25 per mil, which indicate that it is dominantly of marine organic origin and partly degraded. Atomic S/C ratios in the unmineralized part of the carbonaceous rocks have a median of about 1.2, much higher than most similar unmineralized rocks, reflecting not only the abundance of pyrite in the sediments, but also the fact that the organic material contains several percent sulfur. Extracts from the organic material indicate that it is thermally mature and that it reacted with the hydrothermal solutions. Atomic S/C ratios in the mineralized carbonaceous rocks are generally higher than those in unmineralized carbonaceous rocks, ranging to values of 5 and more. These differences indicate that significant amounts of carbon were consumed by the reduction of sulfate and metal chloride complexes in the mineralizing fluids as they passed through the carbonaceous sediments. Direct reaction between organic material and ferrous chloride-bearing, acid-sulfate hydrothermal solutions probably caused continuous deposition of pyrite during this period. Intermittent deposition of gold from chloride complexes by the same reaction was probably facilitated by boiling or C02 effervescence.

Jan 1, 2013

By A. D. Walters

Computer simulation models of preparation plant operations and cost analysis have been used to determine the profitability of individual coals. The model's input consists of raw coal size and washability analysis, operating cost data, and raw coal and clean costs. The model's output predicts yields, qualities, costs and profitability for an individual coal.

Jan 1, 1987

By Charles H. Grant

Blast design methods generally deal with end points or limits of design such as spacing, burden, stemming depth, etc. Even cratering design deals with limits defined as a function of energy decay to a limit. Although this crater method provides a better method than trial and error judgment it does not take into consideration the distribution of energy throughout the material to be blasted. This paper deals with a method of examining this distribution with the aid of a computer and how changes in blast design affect this distribution. First I would like to explain the equation used to develop the energy summations throughout the blast. As shown in Figure I a series of drill holes are drilled to various depths starting by placing the explosive charge on the surface and then at various depths until a sufficient depth of hole is reached to exceed the ability of the explosive energy effect to reach the surface of the ground. All volumes of explosive are the same, all holes contain the same explosive and the drill hole diameter is the same.

Jan 1, 1980

By T. W. Newell

Small tonnage ore bodies can be developed at a profit on a short life basis. Such is the case of the Bardon Mine in. the Big Indian Mining District in San Juan County. Utah. Faced with a small initial tonnage of high grade uranium ore, the Shattuck Denn Mining Corporation Engineers developed some new ideas for sinking the shaft and planned extraction to warrant the capital risk to mine a limited reserve. The Bardon Mine is located fifty miles southeast of Moab, Utah in the south end of the Big Indian Mining -district. Shattuck Denn Company, a wholly owned subsidiary of the Shattuck Denn Mining Corporation, manages and operates the property under an operating agreement with Kerr-McGee Oil Industries, Inc. of. Oklahoma City. Oklahoma, and Anderson Development Corporation of Albuquerque, New Mexico. Based. on Kerr-McGee drilling., a tabular ore body about 350 feet long by 250 feet wide with an average thickness in excess of seven feet was indicated.- The ore body strikes easterly-westerly and dips from nine to twelve degrees to the south. Uraninite is the dominant uranium ore mineral associated with vanadium. The ore occurs in an arkosic conglomeratic sandstone with some interfingering of mudstone and shale in the Mossback member of the Chinle formation in contact with the underlying Cutler formation. The ore horizon is overlain with 40 to 60 feet of mudstone and shale. Fortunately, the back. immediately over the ore is a reasonable competent shaley sandstone which has made a fairly good. environment for roof bolting.

Jan 1, 1960

By Greg Border

Many unique ventilation problems have been faced as Avery Island Mine's large openings have been mined. High humidity of outside air combines with the hygroscopic salt to create a corrosive atmosphere. Massive rooms preclude routine use of brattices to direct air flow to the working faces. Large amounts of explosives are consumed in single blasts. Resulting concussion pounds air control structures and ANFO ignition creates large amounts of nitrogen dioxide in single rooms. Geologic constraints confine new shafts and slopes to areas thought to be free of potential ground water hazards. Dust control techniques are limited by dry product demanded by customers. The Avery Island Mine's ventilation system has evolved to deal practically with the conditions and to dependably provide fresh air to the miners. International Salt Company's Avery Island Salt Mine, a multiple level room and pillar operation, has been mined steadily since about 1900. It is known as one of the "Five Island" salt dome mines of South Louisiana's Gulf Coast. Production from the area places Louisiana first in United States rock salt mined tonnage, according to the United States Bureau of Nines, 1982 (1). International Salt Company is a major force in U.S. salt production, as it also operates mines in Detroit, Michigan; Cleveland, Ohio; and Retsof, New York; a solar salt facility in Bonaire, Netherlands Antilles; and a solution mining plant at Watkins Glen, New York.

Jan 1, 1983

By A. K. Kelly

Potash was first discovered in Saskatchewan in 1943 but its continuous extraction did not begin until 1962. In the years since then, potash has played an important role in the economic and political life of the province. And, as is well-known, the most eventful time in the life of the industry occurred in 1975 when the Government of Saskatchewan decided to become a major participant in potash production. To understand that decision, however, requires an understanding of the economic development of Saskatchewan and of relations between the industry and the government prior to 1975. This year, Saskatchewan celebrates its 75th year as a province. For most of those years, we have been an agrarian economy and society, dependent on exports of cereal grains, mostly wheat, for a livelihood. Even today, agriculture accounts for about 25% of the province's Gross Domestic Product (Economic Review, 1979, p. 7) and difficulties in agriculture spread rapidly to the rest of the provincial economy. The difficulties and risks that go hand in hand with being a "one crop" economy were known as long ago as 1920 but were not fully appreciated until the combination of depression and drought in the 1930's turned the prairie grain- belt into a dustbowl. Some idea of the severity of the depression is revealed by the following data: in 1928, Saskatchewan produced 321 million bushels of wheat. By 1931, the total fell to 132 million bushels and, in 1937, to a mere 37 million bushels. The value of agricultural products sold off farms fell from $273,000,000 in 1928 to a meagre $51,000,000 in 1937. The impact of such a fall of agricultural incomes was catastrophic since about 70% of the population of some 921,000 persons lived in rural, agriculture-dependent areas (Britnel.1, 1939, p. 14).

Jan 1, 1980

By Robert R. French

Beneficiation of-low-grade nonmetalliferous mineral deposits by electronic color sorting is currently undergoing a period of rapid development. For those deposits in which the specific gravity, strength, soundness, electric and magnetic properties of the ore and gangue are similar the possibility of separation by color, reflectivity, or fluorescence offers hope for utilization of much poorer quality ore than previously thought possible. For those ores in which consistency of color is required or for which a dry process is preferred, the electronic color sorter is particularly adaptable. Electronic color sorters were first designed to process agricultural products and were small low-capacity units. However, the recent introduction of larger machines designed to process 6-in, diameter ore at a rate of 30 to 50 tph (Anonymous, 1966a), has brought color sorting into the capacity range required by many mineral producers.

Jan 1, 1967

By C. G. Snavely

Martin County Coal Corporation produces coal from seven continuous miner sections in two coal seams which are often interlaced with rock partings. Because of high clay content and coal oxidation, all minus 100 mesh material is discarded in the preparation process. We began experimenting with various drum lacings on continuous miners in 1983 to improve product size consist and increase machine cutting rates. To date, + 6.35 mm material has increased from 61 to 73% of mined product, minus 0.15 mm material has decreased from 6% to 4% of product, and machine cutting rates have increased by 50 percent.

Jan 1, 1985

By Ramon S. Pizarro

The Masbate Province, Philippines, has been a gold producer for many years. Several gold properties were profitably operating until the outbreak of World War II in 1941. One of these properties was the Masbate Consolidated Mining Company that at the time showed an impressive production rate of more than 4,000 metric tons of ore per day and one of the lowest milling costs on record in the country at that time. Interesting enough, t was the milling equipment left abandoned at Masbate that gave birth to one of the giant copper producers in ASIA. In 1955, Atlas Consolidated Mining and Development Corporation started a new operation at its copper property in Cebu with the seven 2.4m 0 x 3m long (8'0 x 10' long) ball mills left abandoned at the old Masbate Gold Mine. Now, 25 years later, Atlas is processing over 100,000 metric tons of copper ore per day through its three copper concentrators, and, the seven old mills are still grinding, copper ores now.

Jan 1, 1981

By Kefton H. Teague

History of the feldspar industry in the United States has been summarized by DuBois (I)*. The earliest production of feldspar in the United States is reported to have been from Mitchell County, North Carolina, about 1744, with the product shipped to England, In about 1825 several pegmatites were worked to a limited extent in Connecticut, with the production shipped to England. The first feldspar grinding facility was constructed about 1850 in Connecticut, with chaser mills used. Feldspar has been produced continuously in the United States since about 1870. Feldspar is produced from the following states: North Carolina, California, Georgia, Connecticut, South Carolina, South Dakota, Kansas, Oklahoma, Virginia, Arizona, and Wyoming. Total United States production for 1969 will amount to approximately 900,000 tons. The most current published figures for world production is 1966, at which time 2,165,000 tons was produced. It is estimated that world production of feldspar for 1969 will amount to 2,410,000 tons. Historically, feldspar has been produced by hand sorting and hand cobbing of coarse block feldspar obtained from the intermediate and wall zones of zoned pegmatites. In the United States the reserve of known block feldspar, recoverable by hand sorting is nearing depletion. More emphasis is now placed on feldspar sources contained in finer grained rocks, especially coarse granites or fine-grained pegmatite and beach, dune, and river sands from which the feldspar is obtained by beneficiation.

Jan 1, 1970

By Larry Cook

During the past year the news media has come in for its share of criticism. Some of it, without doubt, is justified. Much of it, like that which has been leveled against some of the rest of us, is not. We can sympathize with the newspapers and magazines, the radio and television stations. Like the coal industry, which I represent, they are a part of the free enterprise system. They depend upon advertising for their existence, and advertisers patronize those media which reach the most people interested in their product. The various news media are therefore In avid competition for circulation. Although they do have an unquestioned influence on the public, they are primarily a reflection of the public and it is in this context that we will consider them. Granted that this reflection is sometimes a bit distorted, let us admit that any subject which does not strike a responsive chord In the public will soon be dropped by the media.

Jan 1, 1970

By Joseph R. Hatch

During the past ten years detailed elemental analyses of approximately 8,000 well-documented samples of coils in the United States (including Alaska) have been produced by the U.S. Geological Survey and the various State geological surveys. Examples of data listings include Swanson and others (1976) Gluskoter and others (1977) Hatch, Affolter, and Davis (1979), and Wedge and Hatch (1980). These analyses serve as a basis for evaluating elemental abundances in coals from the various coal province, regions, and fields. When combined with additional geological and geochemical data, some of these analyses give insight into when certain elements were introduced into coals, and which physical and geochemical parameters are most important in determining coal elemental composition.

Jan 1, 1982

By Donald Babbitt

In 1971, during the planning and design stages of a $300 million expansion, the Iron Ore Company of Canada Ltd. through its Engineers, Canadian Bechtel Ltd., came out with a preliminary request for two (2) 10,000 LTPH belt conveyor scale systems. These Systems were to provide weighing accuracies within 2.5% of the iron ore pellets and concentrates in transit on two (2) 72" wide conveyors from the stockpiles to the ships. Each conveyor system would be fed by a rail mounted bucket wheel reclaimer, with the conveyed material moving directly to the ship loaders with no inter- mediate surge and/or storage bins between the stockpiles and the ships. The bucket wheel reclaimer discharge rates would vary from 0-9600 LTPH in cyclic periods, with the periods varying from 1-5 minutes - dependent on the level of the reclaim buckets in relation to the stockpile as well as the slewing rate of the reclaimer. There would be frequent interruptions for bucket wheel repositioning (laterally and vertically), changing ship holds, and trimming ship holds. These frequent zero flow conditions, approximately 500 per 150,000 ton ship, could last 1-5 minutes. In addition, the conveyors on which the scales were to be mounted would be over the water and subject to the wind and cold of Northern Quebec. These Systems would be in use 350 working days of the year and would load 30,000,000 LT/yr. (An average of 90,000/working day).

Jan 1, 1975

By Jorgen Elbrond

In a stream of ore in an underground mine or in a beneficiation plant bins are installed between machines or machine system. When the upstream machine is stopped the downstream machine can continue operation for a while and vice versa. The paper describes a procedure for calculating the total capacity of a system consisting of two machines with an intermediary bin as a function of the bin's live volume and of the installed machine capacities and their production variations, which are defined. Extensions to several machines in parallel and in series are shown as well as practical examples.

Jan 1, 1982

By John P. Capp

In recent years limited markets have been developed for fly ash, the dust removed from coal-burning powerplant stacks, but most of it is still dumped in spoils areas at a cost ranging from 20 cents to $1.75 per ton. Aside from this cost, the creation of huge spoils areas can present a considerable aesthetic problem. Since the present annual fly ash output of about 20 million tons will probably reach 30 million by 1970, and because satisfactory disposal areas are becoming more limited, markets for much larger quantities of the waste are needed to keep disposal costs from becoming a significant economic factor in coal-burning powerplant operation. Current stress on air-pollution control and beautification, plus the vital need for good powerplant economy, makes it imperative, therefore, that coal producers and consumers expand markets and develop new applications for fly ash. Markets for established uses can be increased by making a greater effort to sell fly ash. New large tonnage markets for fly ash should be sought via more intensive, coordinated research. The economics of fly ash utilization underscores the vital role that must be played by research. To be competitive with other products, processes for the conversion of fly ash into marketable materials face difficulty in regard to two important economic factors--transportation cost and product utility--the other economic factors are favorable. Raw material costs of fly ash, for example, are quite attractive, and supply is no problem because there are many coal-burning powerplants in operation and many more are planned. Demand for products made from fly ash will grow if their utility is established and a good sales program is initiated. The major problems then are transporta¬tion costs and development of useful products.

Jan 1, 1966