Search Documents

By C. H. Cox

The Alumet Company of Golden, Colorado, is currently engaged in the development of their Diamond Creek and Lanes Creek phosphate ore bodies located near Soda Springs, Idaho. The Alumet Company is a partnership of National Steel, Southwire Co., and Earth Science Inc. Davy Powergas, Inc., of Florida was contracted by Alumet to perform an evaluation study of these properties and, in general, determine the tonnage of altered and unaltered phosphate reserves which would be amenable to beneficiation and production of merchantable phosphate rock (defined as material with a P2O5 content of 3 1.0% and greater). The Colorado School of Mines Research Institute was retained by Davy Powergas to develop a beneficiation method for the studies of the altered and unaltered ores. Ore reserves were classified by Davy in a comprehensive range of categories such that any partial grouping could be made as dictated by future mine planning, mine or mill design, or prevalent economic conditions. Categories included ore horizon, stripping ratio, degree of certainty of their existence, and physical and chemical characteristics. The last category was of interest for beneficiation considerations in that it dealt with the degree of alteration of the phosphate ore.

Jan 1, 1979

By Donald Towse

The Permanente plant of Kaiser Cement & Gypsum Corporation is located at a unique thick deposit of Calera Limestone (Figure 1) on the southwest side of San Francisco Bay. Limestone is rare in the eugeosynclinal Franciscan assemblage, constituting less than 0.1 percent of the total volume. On the northwest part of the San Francisco peninsula Calera Limestone is present as isolated masses from the type sect ion near Rockaway Beach southeastward for ten miles, where the belt is truncated by the San Andreas fault. The large Permanente deposit is sixteen miles south of the truncated belt, on the northeast side of the San Andreas fault. Scattered small exposures are known for about twenty miles southeasterly from Permanente. (1,2) Most deposits of Calera are thin; the type section is about two hundred feet thick. At Permanente, however, the normal limestone section contains at least four hundred feet of limestone; and, due to folding and extensive faulting, the total vertical thickness of the limestone section is over 1400 feet. The unusual thickness of limestone is due to low angle thrust faulting. This fortuitous structure formed a deposit of limestone that supplies an 8,500,000 barrel cement plant in a major metropolitan market.

Jan 1, 1966

By Warren N. Warhol

The mutual growth of the rare earth industry and the Mountain Pass Operations was no coincidence. It was the commercial availability of rare earths on a scale first made possible by the capacity of the Mountain Pass Operations that spurred research and development efforts toward new applications for rare earths. The first important demand on Mountain Pass was europium oxide for the activation of red phosphor for color television tubes in 1964. Since that time, other rare earths have become even more important, and Molycorp is continuing to supply an ever widening variety of rare earth concentrates and compounds. We enjoy saying that rare earths are not really rare, and that they are not earths, either. Of course, we are talking about the 15 metallic elements with atomic numbers 57-71, called the lanthanides, which occur in nature always together in very similar proportions. Their scarcity can be gauged by the fact that there is more cerium in the earth's crust than there is tin, and more europium than cadmium. The word "earths" comes from the early chemical term for oxide. The rare earths were discovered as oxides, and the term has persisted.

Jan 1, 1980

By Stanley J. Gasior

Most bituminous coal mined near Eastern industrial areas requiring high Btu pipeline gas is caking and therefore unsuitable for fixed-bed pressure gasification by present techniques. If the caking property of such coal can be destroyed the resulting fuel can be gasified in a fixed bed at pressure with steam and oxygen as a preliminary step in making a high-Btu gas. To find a practical way to convert strongly caking coals of granular or small lump size to noncaking fuel was the object of this study. In previous work strongly caking coals of 1/8- to 1-1/2-inch size was converted to a noncaking coal char by treatment in a static bed in about 3 hours [1/]and coal of 18-100 Tyler mesh in a fluidized bed in about 5 minutes.[2/] An inert gas such as `steam, nitrogen, carbon dioxide, or a mixture of all three with a small amount of oxygen was used in both studies. In our work a strongly caking bituminous coal from the Pittsburgh seam of 4-8 Tyler mesh size was converted to a-noncaking form in free-fall in about 2 seconds by dropping it through a countercurrent flow of steam containing 4 to 7 percent oxygen at 1,150°-1,200° F and 300 psig. This method should also be applicable to smaller-sized material.

Jan 1, 1965

By Andrew W. Jenike

There used to be a time when bins were designed for total volume and placed in any available place of the plant. Poke holes were provided and feed was maintained by manual prodding, lancing, hammering, and by various mechanical flow-profiting devices. Little thought was given to what occurred inside the bins and why materials did not flow. Indeed, such mental effort was hard to justify while low-cost manual labor was plentiful, quality standards low, and rates of feed moderate. The past fifteen years have seen a drastic change in these conditions. We all know that labor for hard manual work is becoming unavailable at any wage, level. Standards of product uniformity are continuously rising. This uniformity is just as important in a fine ore feed to ball mills as it is in a cattle feed or in a flour mix. Rates of feed now frequently exceed 2,000 tons per hour per feeder. At that rate there is no time for, lancing or prodding. An efficient storage, plant contains a known available volume of bulk solid, and feeds it at the required time, at the prescribed rate, and without degradation of the product. A storage bin may also perform other functions such as blending of different grades, degasification of aerated, powders, isolation of different gaseous media. A contact bed of particles flowing by gravity in counter-current with a gas or liquid may be used as a continuous reactor. Gas or liquid pressures can be simply contained by, a sufficient head of flowing solid.

Jan 1, 1968

By C. F. Curry

In the early 1940's Humphreys Mining Company in Florida pioneered heavy mineral mining with a dredge in the United States, In 1948 Du Pont, in conjunction with Humphreys, opened their first of two mining operations recovering a titanium dioxide product in Florida. Later on in 1952 Du Pont opened their second plant, both of which used a cutterhead suction type of operation. This process is also used in heavy mineral mining in Australia and Africa. In 1957 ASARCO started prospecting in New Jersey. Test borings indicated a large deposit of ilmenite bearing heavy mineral sands had been deposited and concentrated in an area near Lakehurst in central New Jersey. Humphreys Mining Company was contacted about the possibility of mining the ASARCO New Jersey property in much the same way as Du Pont and themselves were doing in Florida. An extensive study was made to determine the economic feasibility of mining the ASARCO property. During this study, extensive test drilling and samples for a pilot plant were taken.

Jan 1, 1975

By S. Norman Kesten

The Resource Conservation and Recovery Act, commonly known as RCRA, which amends the previous Solid Waste Disposal Act, was signed into law on October 21, 1976. Members of the mining industry began their contacts with EPA in this area two to three years before the Act finally was passed, and that seemed and probably was all to the good. We reviewed and commented upon their studies and in general tried to acquaint them with the peculiarities and the uniqueness of the wastes generated by our industry, of which they were abyssmally ignorant. I suppose we thought that through the bureaucracy we might have some influence upon the provisions of the solid waste legislation that was being bandied about on the hill. Certainly the industry, in general, did very little direct lobbying, as I recall, and there were several reasons for that. For one thing we conceived that the legislation was aimed at the chemical industy and believed that if their people looked after their interests, ours would be safeguarded automatically. Also, the Federal Land Policy and Management Act (FLPMA) was heating up at the same time and, in fact, was signed into law on the same day. In addition, a great deal of lobbying activity was required by amendments of the Clean Air Act and Federal Water Pollution Control Act that were being put together in Congress. These were conceived to be of far greater importance to our industry than a bill to control mostly chemical wastes and, in fact, new bills in both areas became law the following year. Finally, the solid waste bill, RCRA, was patched together by committee staffs over one weekend and was reported out by a conference committee rather hurriedly. Some little goodies about mining were almost after-thoughts in this process.

Jan 1, 1981

By Thomas M. Turner

Open pit mining, always a demanding task, faces two relatively new problems today: 1. Availability of equipment. Moderate to large draglines can take as long as 6 years from date of contract to date of operation. 2. Environmental restrictions. Strip mining in the minds of environmentalists compares unfavorably on the scale of social desirability to the activities of Jack the Ripper and Attila the Hun. Specifically, lowering of the water table to allow strip mining in the dry is being looked upon with increasing disfavor. The modern dredge offers relief in both problem areas. Delivery on a major dredge might run 18-24 months rather than 60; and lowering of the water table is precluded, thus minimizing environmental objections. In addition, a lower first cost and potentially increased efficiency may offer real advantages to the miner who is forced away from his traditional mining methods. This talk is dedicated to acquainting the miner with dredge types, advantages, and limitations.

Jan 1, 1975

By L. Michael Kaas

In recent years a number of data processing and analytical techniques have proven to be useful to engineers and geologists in various segments of the mineral industries. Petroleum companies were among the first to utilize the computer to store well data files and to analyze that data for exploration purposes. A few years later, metal mining companies began to apply the same basic computer methods to problems in mineral exploration, ore reserve evaluation, and open pit mine planning. Because of the increasing complexity of planning for coal mines and land reclamation, a case study was undertaken to evaluate the usefulness of computer techniques to assist mining engineers and geologists in mapping coal deposits, evaluating coal reserves, strip mine planning and land management. The data used in the study was provided by the Illinois State Geologic Survey. This paper describes some of the results of that study. First, considerations for the development of a computer data base for coal deposits are presented. Next, a series of analytical techniques for processing the data is described. Finally, the case study is presented to illustrate how the coal data base and the analytical techniques could be used in actual practice.

Jan 1, 1973

By Jess W. Smith

The carbonaceous Monkemeyer sandstone member of the Creede Formation on Bachelor Mountain hosts alteration and mineralization which contrasts with other silver deposits of the Amethyst system. More than 20 million ounces of silver are contained in disseminated mineralization in the volcaniclastic conglomerates and sandstones. Hydrothermal fluids entered the Creede Formation directly from the Amethyst fault system and mixed with flowing meteoric ground waters trapped beneath the Monkemeyer sandstone. Portions of the basal rocks of the Creede Formation were argillically altered by more dense acidic fluids generated by boiling. The carbonaceous base of the Monkemeyer and much of the conglomerates below were mineralized and well silicified. Deposition of the mineralization resulted from two processes: (1) reduction by carbon in the Monkemeyer, and (2) fluid mixing in the conglomerates. Monkemeyer mineralization is confined to the carbonaceous basal material and silver content is relatively consistent. Silver is contained in acanthite which is commonly associated with traces of galena, chalcocite, covellite and sphalerite. Fluid mixing and mineral deposition in the poorly sorted conglomerates was controlled by the highly variable porosity and permeability. Anomalous silver contents are dispersed throughout a large volume of conglomerates but zones of higher silver content reflect the crude layering of the conglomerates. Acanthite is finely disseminated in pore spaces and partly replaces some detrital magnetite. other metallic minerals are rare in the main zone of mineralization.

Jan 1, 2013

By C. Y. Chen

In order to put an end to the uneven environmental standards and enforcement established by various coal mining States in the United States, the Congress passed and the President signed the Surface Mining Control and Reclamation Act (Public Law 95-87 or the Act) on August 3, 1977. Within one year after passage, the Secretary of the Interior was directed to promulgate permanent program regulations implementing Title V provisions of the Act. These regulations were to form the basis for State regulatory programs under the Act and to allow States to assume primary regulatory responsibility. In order to implement the underground mining provision of the Act, the Secretary is directed in section 516(a) of the Act to promulgate rules, but ones which take into consideration the distinct differences between surface coal mining and underground coal mining. The regulations developed by the Secretary and promulgated on March 13, 1979, with respect to subsidence control, included (1) a subsidence control plan as part of the permitting process, (2) substantive provisions establishing performance standards for subsidence control, and (3) provisions providing for the prohibition of mining under perennial streams, impoundments larger than 20 acre feet, and certain public facilities and urban areas.

Jan 1, 1985

By Rudolf Fahn

Bentonites are best suited for the preparation of acid activated clays with efficient adsorption properties. They are weathering products of acid volcanic ashes and their natural deposits are world-wide spread. The main constituent of bentonite is the aluminium hydrosilicate nontmorillonite with a high ability to swell. Süd-Chemie owns bentonite deposits in Germany and subsidiaries in Italy, Mexico and Arizona.

Jan 1, 1979

By Roberto Zaragoza

Historically, the control of flotation operations has been viewed by many as an art. Only recently has process measurement and control come to be viewed not as an ?art? but as a very complex and productive science. In recent years, process control applications to flotation plants have been established and already some gains have been reported for several industrial operations using individual stabilizing control loops including level, pulp flow, pulp density, reagent addition rate and pH (Paakinen, 1979; Hales, 1985). The use of process control computers combined with on-line x-ray florescence (XRF) in industrial flotation circuits has made the application of more sophisticated control techniques feasible in the mineral recovery process. In spite of the availability of reliable instrumentation in modern flotation plants, satisfactory control strategies are difficult to develop and implement. Extremely important factors such as changes in ore type, liberation characteristics, flotability, degree of oxidation on particle surfaces, and specific gravity constitute unmeasured disturbances to the process. Most current control systems cannot adapt specifically to such disturbances.

Jan 1, 1987

By Ronald L. Wiegel

Success has been achieved in developing mathematical models of rod mills, ball mills and recently to a limited extent autogenous grinding mills. There is also considerable activity in the development of mathematical models of various mineral concentration opera¬tions, such as flotation, magnetic separation and electrostatic concentration. However, at present there is a technological gap which hinders the integration of both size reduction and mineral concentration models into an overall process simulation model. This gap exists because size reduction models have been aimed at describing the size of the product and have not dealt with the equally important problem of identifying the product composition in each size fraction. Without this information the concentration model is ineffective. This situation is especially critical in the simulation of the magnetite-taconite beneficiation process, where a portion of the ore is rejected from the process following each stage of size reduction. Consideration has therefore been given to the merging of a size reduction model and a mineral liberation model to permit prediction of mineral composition as a function of size. The results of this integration of size reduction and mineral liberation models are discussed from both theoretical and practical viewpoints using batch grinding data for a magnetite iron formation sample as a demonstration vehicle.

Jan 1, 1975

By George E. Peacock

Campbell Red Lake Mine is situated at Balmertown, in the Red Lake District of Northwestern Ontario, Canada. This area is some 120 miles north of the Trans Canada Highway and is some 160 miles Northeast of Winnipeg, Manitoba. The majority of our 300 employees live in Balmertown, which is a community of some 1,200 people, situated adjacent to the mine proper. The mine is serviced by a single shaft 4,300 feet deep. There are 27 levels at 150 ft. intervals. Stoping is being carried out down to the 20th level with only preliminary development having been done on the bottom 6 levels. The majority of our mill feed of 825 tons per calendar day comes from above the 10th level. Gold occurs as specks and streaks in bluish-grey to white quartz carbonate veins. It is extremely fine grained and most is invisible to the unaided eye. In addition to Gold the veins carry varying amounts of sulphides such as, Arsenopyrite, Stibnite, Pyrite, Pyrrhotite and Sphalerite. A minor amount of silver occurs as an impurity in the gold. Arsenopyrite is a marker for the gold ore at Campbell. The average grade of the mill feed is 0.7 oz. of gold per ton. The ore is dumped into an underground ore pass that feeds to a jaw crusher on the 20th level that reduces the rock to a maximum size of 4". This material is hoisted by skips to an ore bin in the head frame.

Jan 1, 1975

By Harald F. Solberg

A preliminary study of the performance of a 4-inch Krebs cyclone at near rope conditions and different feed slurry temperatures was completed. Results suggest that temperature influences the x50c size which, in turn, did not depend upon spigot diameter. The bypass correction to a reduced efficiency equation incorporating the concept of a critical size xo was a function of fractional water recovery to underflow and may depend on feed size and feed percent solids. Further experimentation is required to develop an accurate model at near rope conditions.

Jan 1, 1981

By James A. Erdman

This overview briefly describes some examples of applications and difficulties in using plants that are drawn from the literature and from field experience. Because of the generally low Au concentra¬tions found in plants, the analysis of plant tissue is critical to the successful application of the biogeochemical method of prospecting. Neutron activation analysis is the most widely used method to detect Au in plants, due largely to its sensitivity; levels in the parts per billion range are easily attained. Two general types of sampling media are used in prospecting for Au: humus and living plants. Humus has been widely used in Canada, but the sampling of plants has increased there and elsewhere in recent years. The use of douglas-fir (Paeudotsuga menziesii) at a Au-bearing stockwork in Idaho is a prime example. A maximum Au concentration of 14 ppm was detected in the wood ash of this coniferous tree, well above the normal background concentration of about 0.15 ppm. Among shrubs that might be useful in Au prospecting, sagebrush or wormwood (genus Artemisia) could be sampled because it is extremely responsive to concealed mineralization. It has been used extensively in the Soviet Union and could be used in areas of the western United States where disseminated Au occurrences might be located. Among the problems one may encounter in using plants for Au prospecting are (1) physiological barriers, by which many plant species simply do not absorb Au at detectable levels; (2) misconceptions of soil-plant correlations; (3) localization of Au in plant tissue; and (4) the variation of Au concentrations due to season. Despite these limitations, biogeochemical techniques can complement or replace other geochemical methods currently used.

Jan 1, 2013

By Ignacio Salazar

Somebody sure gave me the wrong title. I can talk much more freely about the impact of the anti-nuclear movement on the DRILLING industry in New Mexico. In a word, it is being "clobbered." It doesn't seem like very long ago that my brothers and I were busy trying to find enough new equipment (and trying to talk bankers into lending us enough money) to keep up with drilling work we could get. Seemed like no matter how hard we worked, and how much money we borrowed, we were always one step behind where we wanted to be. We had so many holes to drill that all our crews were working three shifts a day, and over several states. The nation needed energy, and we were ready to help supply it. Exploration and development drilling jobs were all going full-blast. We had trouble keeping up with them. With luck, we figured we'd be able to get all our equipment out of hock before all the necessary uranium mines were developed.

Jan 1, 1979

This paper presents a method for evaluating the economic feasibility of solution mining a hypothetical uranium roll-front deposit. It is assumed the wellfield will be operated in a prudent manner and that leaching tests were performed in depth in both lab and field (push-pull) prior to startup. Leach test results are reduced to two important parameters and used as the basis for solution mining a wellfield. This case study assumes a 10 mil- lion-lb uranium deposit with 40 possible small wellfields; four are kept in operation simultaneously until the deposit is depleted. The wellfields have different ore reserves and grades, lixiviant circulation rates, leach rates, and peak concentrations, and thus the daily uranium production will vary. Daily production is used to assess the profitability of a particular lixiviant and the mode of well- field operation in light of realistic market price estimates. The mathematical procedure is simple and straightforward, based on reasonable in-situ leaching relationships as well as accepted accounting practices.

Jan 1, 1985

A combination field and office study of mining districts in Southwestern U.S.A., conducted in 1949 - 1950 by United Geophysical Company, embraced all of the essentials for a successful exploration project including factors such as geology water, transportation and many more. Perhaps the best known of several high priority areas chosen from the study was the Twin Buttes or Pima District in Arizona, however, the Turquoise District also ranked very high on this priority schedule. Following the discovery of the Pima Mine in 1951 and 1952, United initiated additional preliminary geological, geophysical, drilling and claim location work in the Turquoise District, but stopped shortly thereafter, when ASARCO began adjoining competetive activity. During the summer of 1957, sometime after ASARCO abandoned their claims in the area, Minerals Exploration Company began intensive exploration in the Courtland-Gleeson part of the District. This program was terminated in 1958. Later Bear Creek Mining Company supplemented the discovery endeavor with their own program during the period 1960 through 1962. This paper summarizes most of the geophysical work done by all of the groups except ASARCO and is intended to complement the recent paper "General Geology and Some Structural Features of the Courtland-Gleeson Area, Cochise County, Arizona" by Mr. Otis McRae of Bear Creek Mining Company.

Jan 1, 1966