Search Documents

By Clinton Strachan, Rob Dorey

10.1 INTRODUCTION This chapter presents considerations which should be applied to heap leach pad site selection, site evaluation, and design, relative to the geotechnics of the site and ore. 10.1.1 General Guidelines are presented covering the topics encountered in design and construction of heap leach faci1ities. Because geotechnical characteristics vary from site to site, not all geotechnical topics associated with a specific heap leach facility are presented, and there may be exceptions to some of these guidelines. The general features of a heap leach facility (from Chapter 1) to be discussed in this chapter are: • Leach pad (including leach pad foundation and liner); • Heap; • Solution storage faci1ities (for pregnant and barren process solutions) ; and • Solution collection facilities (which collect and convey solutions in the heap and convey them to solution storage facilities). These general features are illustrated in Figure 10.1. Liners for these facilities are discussed in Chapter 11. Solution application systems and the sizing aspects of solution storage facilities are discussed in Chapters 6, 7, and 12. The general features listed above are constructed with and overlie naturally occurring materials (such as ore, borrow soils, and subsurface soils and rock). These natural materials are relied upon to perform in an acceptable manner as a component of the leach facility (such as the liner, drain material, and foundation).

Jan 1, 1988

By J. M. Stewart

The incidence of heat stroke in the South African gold mining industry is today small (less than 1 in 10 6 shifts worked). Acclimatization and selection procedures have been developed and applied throughout the industry, underground working conditions have, and are being improved, and personnel are to-day made more aware of heat stress and its consequences than ever before. Although these actions have, over the years, brought about a steady reduction in the incidence of heat stroke (see Figure 1) the small incidence of heat stroke which persists indicates that heat stress is still a problem. This realization provides the stimulus for the work presented in this paper, which has as its primary objective the development of reliable heat stress limits for men working in South African gold mines. [ ] In keeping with recent trends3I4 the approach followed in this paper is based on the physical principles of heat transfer. Detailed studies of heat transfer from humans have been undertaken,5-l1 and certain of the results form an important aspect of this Paper -

Jan 1, 1980

By Aldo F. Barsotti

The production and consumption of industrial minerals in the United States traditionally have played important roles in mining and in the supply of the bulk of basic raw materials to the economy. This diverse group of minerals extracted and consumed by a variety of industries accounts, on a weight and volume basis, for most mineral-based products consumed in our economy. Industrial minerals form the bulk of the basic raw-materials feedstock for most of the construction, agricultural, and inorganic-chemical-manufacturing sectors, and a good portion of the transportation, manufacturing, organic chemical, and service sectors of the U.S. economy. In this presentation, I discuss current estimates of the amount and value of industrial minerals mined compared with all mining in 1997. I then present a summary of 1997 production of industrial minerals by several end-use industries. This is followed by a historical perspective of the consumption of industrial minerals as a subset of all basic materials, with special emphasis on the aggregates industry. The presentation concludes with a look at the geographic distribution of industrial mineral operations in the United States and some thoughts about the future.

Jan 1, 1999

By M. Robb, S. J. Bate, M. Boisvert

The never-ending quest for gold-bearing ore deposits is a primary industry in Canada, employing people of widely differing expertise. The exploration models for gold deposits are generally geologically complex and the targets have relatively small cross-sectional areas. These problems are compounded in Canada by the minimal outcrop exposure in most mineral provinces and the high percentage of water-covered areas. Naturally the chances of successfully delineating an economic gold deposit are very much greater if all parties involved can act as a team of explorationists constantly confemng amongst themselves particularly as the applicable disciplines generally overlap and complement each other. Three case histories (see Figure 1) are presented to illustrate this philosophy with emphasis placed on the role of the geophysicist in translating the exploration model as defined by the geologist into physically measurable parameters and identifying target areas with similar characteristics. The Conwest-Miminiska property in Ontario is a grassroots exploration play. Additional ore reserves needed to be delineated on the Salmita property in the Northwest Territories. At Laura Lake, near Chapais, Quebec geophysical methods were employed to trace thin high-grade mineral intersections under deep overburden and severe cultural interference.

Jan 1, 1989

By Fathi Habashi

IT APPEARS that the phenomenon of ion exchange by which saline water was converted to sweet was known to Moses and Aristotle. However, the credit for the recognition of this process is generally attributed to Thompson (1850) and Way (1850), who reported that when a soil was treated with either ammonium sulfate or ammonium carbonate solution, most of the ammonia was adsorbed and calcium was released. It was later proved by Eichorn (1858) that the adsorption of ions from ground waters by clay constituents was a reversible process. The first attempts to utilize ion exchange phenomena was in the field of water softening around 1906, using natural and synthetic silicates. In 1935 Adams and Holmes in England observed that crushed phonograph records (phenol-formaldehyde and amine-formaldehyde resins) were capable of exchanging ions.

Jan 1, 1970

By Fathi Habashi

METALS COMMONLY leached may come from one of the following sources: 1) Occurring in nature in the native state, e.g., gold, silver, platinum metals, copper. 2) Produced as by-product of a metallurgical process, e.g., gold, silver, platinum metals, selenium. 3) Produced by reduction of an oxide ore, e.g., copper, nickel. GOLD AND SILVER Cyanidation According to Mellor (1923) the alchemists of the eighteenth century knew that gold was soluble in aqueous solution of potassium cyanide, and the early jewelers probably utilized this fact in gilding. He also mentions that Scheele in 1783 and later Bagration in 1843 noted the solvent action of aqueous solutions of alkali cyanides on gold. Yet it was not until 1887 that the value of this observation was recognized, when MacArthur and Forrest (1887) made use of it in leaching gold from its ores. Since then, the process has spread to every gold and silver mining district in the world.

Jan 1, 1970

By Paktunc. A. Dogan, Nand K. Davé

Unsegregated pyritic uranium mill tailings from Elliot Lake, Ontario, with and without limestone amendment, were subjected to column leaching experiments for the purposes of predicting the onset of acidic drainage and the magnitude of metal and radionuclide release under various treatment and control strategies. The unamended tailings produced acidic drainage after approximately one and a half year. The tailings mixed with various grain-sized limestone did not produce acidic drainage during the study period. The tailings consist essentially of quartz, K-feldspar, muscovite and pyrite. The unsegregated tailings amended with very fine limestone displayed the least amounts of pyrite loss whereas those without limestone amendment had the greatest pyrite losses. Predicted onset of acid generation varied from 16 to 75 years for the top sections and in most cases greater than 100 years for bottom sections of the unsegregated tailings with limestone amendments. Unsegregated tailings mixed with fine- and very fine-grained limestone proved to be the most effective in controlling or delaying the onset of acidic drainage under unsaturated conditions.

Jan 1, 2000

By J de Cuyper, V. M. Lovell, W. Freyberger

The recovery of apatite from the phoscorite ores occurring in the Transvaal, Republic of South Africa, involves a flotation process that is particularly difficult to characterize from a fundamental point of view. However, the reagents used, (tall oil fatty acid, nonylphenyltetraglycol ether, sodium silicate, and sodium hydroxide) can successfully bring about a separation of apatite from dolomitic calcite, which is the most troublesome gangue component. Recently, it has been demonstrated with some flotation feeds that the addition of certain polysaccharides can improve the flotation significantly. It has been shown that the metallurgy obtained is closely linked to the nature of the froth, and this, in turn, is influenced, often dramatically, by the presence or absence of certain of the reagents. The character of the froth depends less on the inherent frothing ability of these reagents than on the presence or absence of fine mineral particles in the froth, and on their surface characteristics and state of aggregation. The polyglycol ether and the polysacchar- ides have been shown to affect these properties, and it is suggested that a major function of these reagents is to modulate the properties of the fine particles in the pulp, thereby changing the character of the froth and giving rise to improved results.

Jan 1, 1976

By J. Mark Richardson

Steady-state flowsheet simulators for mineral processing plants have evolved to a current high level of utility and accuracy. Reliable, general-purpose, semi-empirical models now exist in nearly all unit operations categories particularly in the areas of comminution and classification. .These models, installed as user-selectable functions within the integrated frame- work of flowsheet balance-solver software systems, can be strung together to represent any plant configuration. In addition, CAD-like graphics, data reconciliation and model parameterization functions have become standard features of the current generation of integrated plant simulators. These advances have given engineers the capability to investigate many different plant scenarios while requiring a minimum of actual plant testwork. This paper describes a methodology and an integrated software package which are being successfully applied in a number of operating plants worldwide to predict plant performance under changing conditions. Those conditions which can be changed include effect-of ore type, feed size, water addition rates, equipment geometries and flowsheet modifications. By using data from actual plant optimization exercises in real mills, the paper illustrates and out- lines a technique which includes plant data collection, ore breakage testing, flowsheet simulation, model-fitting (parameterization), data adjustment and model experimentation. Brief descriptions of some unit operations models, such as autogenous mills and cyclones, are provided as examples of the current state of such models. Ore breakage testing and its relation to certain models is also discussed. Computer- generated size-distribution graphs, along with tabular data generated by the simulator, round out the presentation and serve to demonstrate the real- ism and accuracy of the models. The paper concludes with a partial list of cases where this technology has been successfully applied.

Jan 1, 1992

By M. C. Roberts

The consumption of industrial minerals, like most other commodities produced from the earth, depends on the demand for the goods and services that use these materials. Minerals are not generally used directly by final consumers (table salt is a notable exception) but instead are used to either make products that are then purchased by customers, or the minerals are used to make industrial products that eventually contribute towards producing other goods and services. Therefore the demand for industrial minerals in most uses is derived from the ultimate demand for goods and services by consumers. The problem for producers of industrial minerals is that the demand for their mineral product fluctuates greatly in response to the changes in the production of goods and services over the course of the business cycle. In this respect, the producers of industrial mineral are innocent victims, subject to market fluctuations outside of their control. Because the demand for most minerals depends on the demand for the product and because minerals typically make up a minor portion of the costs of producing the product, changes in the price of the mineral often do not influence demand for it to a significant degree in the short run. This is described as a very low price elasticity of demand, as shown by the steep slope of the hypothetical demand curve in Figure 1. This demand curve shows that changing the price of the mineral does not alter the quantity demanded very much, but shifts in the demand curve will be the important determinant of the quantity of the mine.ra1 that is sold. The shifts are caused by the changing demand for the products using the mineral over the course of the business cycle.

Jan 1, 1994

By J. H. Tylczak, R. Blickensderfer

Impact and abrasion properties of various commercial US grinding halls were evaluated and compared by the Bureau of Mines, US Department of the Interior. Laboratory tests were conducted on balls obtained from eight major US manufacturers. The halls included forged steel, cast steel, and alloyed white cast iron and were subjected to repeated impacts until they broke or until 300,000 impacts were exceeded. Pin abrasion tests also were conducted. The results showed wide differences in impact lives, ranging from a few thousand to over 500,000 impacts. The life of inferior commercial halls was increased five to six times by a laboratory tempering heat treatment. For halls that did not break, the major impact wear mode was spalling and ranged from an average rate of 0.28 to 4.46 mg per impact. The softest halls (steel) had excellent impact resistance but low abrasion resistance. The abrasion resistance of the steel halls generally increased with hardness. The alloyed white cast irons had about twice the abrasion resistance of the steel halls. Users should become aware of the wide variations among commercial halls, and ball manufacturers should be aware that their product can he improved.

Jan 1, 1990

By S. Zamna, M. E. Defoe, Franklin T. Davis, Earl Rau, Yarroll. Warren H., Paul D. Chamberlin

This section contains a description of the ore processing methods of the walled industrial minerals that are not described in major sections of the book. Table I contains the production figures for each of these commodities in the United States and the world. Specifications for concentrates or final mineral product are also summarized as well as prim for them at the time the section was written. In each chapter an attempt has been made to provide the reader with information on the common commercial mineral or minerals involved with the commodity, some of the uses. the processes used to recover and concentrate the minerals, as well as geographical areas where these process are utilized.

Jan 1, 1985

By J. C. Hower

The Hardgrove grindability index (HGI) is a widely used coal-quality parameter with applications in coal mining, beneficiation, and utilization. An understanding of the petrology of the coal is fundamental to understanding the validity of the HGI in the given application. The HGI varies with coal rank, increasing (greater ease of grinding) with increasing rank through the high-volatile bituminous rank range; and the HGI varies with changes in the maceral and microlithotype composition, decreasing with an increase in liptinite and liptinite-rich microlithotypes. In this review, the .fundamental relationship between HGI and coal petrology, and consequently its relationship to coal utilization, is examined.

Jan 1, 1999

By John F. Papp

Chromite is used both as a metallic and nonmetallic mineral. Chromite ore is used as the source of chromium by the metals industry and is used, without chemical alteration, in the refractory and foundry industries. Chromite ore is also the source of chromium for the chemical industry. On average worldwide far more chromite ore is used by the metallurgical industry than by any other industry. Thus, although the primary purpose of this chapter is to describe the nonmetallic uses of chromite, the metallurgical uses must also be discussed in order to provide a complete description of this commodity.

Jan 1, 1994

By Fernando Pendás, Jorge Loredo, Alumudena Ordóñez

Water derived from mine-tailings typically contains high concentrations of H+, SO4, Fe and other metals, and it frequently suffers a decline in pH and the development of acidic mine drainage (AMD). A paper describing the results of a series of laboratory experiments with real AMD and a subsequent field trial with a in situ pilot system to assess a potential method for remediating tailings-derived water is presented here. After testing different organic substrates, residence times and flow conditions during two years to determine the most appropriate treatment for a polluted Spanish AMD, a pilot scale system combining SAPS, ALD, oxidation/sedimentation ponds and an anaerobic wetland was designed. Preliminary analyses of effluent samples indicate acidity and metal removal is occurring within the system, although sulphate removal is not complete. The results of this small-scale field trial suggest a potential cheap, long-term alternative for remediation of acid mine drainage.

Jan 1, 2000

By David R. Klug, Chris Gause, Troy L. Page

The Inter-Island Tunnel is one of two undersea tunnels which are part of the Boston Harbor Clean-Up Program. The tunnel is 7.7 km (25,160 ft) long, bored to a 4.3 m (14 ft) diameter in the Cambridge Argillite Formation and was finished to a 3.5 m (11.5 ft) diameter final concrete lining. The owner is the Massachusetts Water Resources Authority (MWRA) who is a regional authority responsible for overall design and construction. The tunnel's primary purpose is the transport of untreated effluent from Nut Island facility in Quincy, MA to the new treatment plant at Deer Island. Two sludge lines are installed for the transport of sludge from Deer Island to Nut Island. During construction the contractor encountered fault zones, fractured strata, and soft ground tunnel sections which liberated more ground water than was originally anticipated by the project designer. Ground water was controlled during mining and the placing of the final lining. The final lining of cast-in-place concrete had to be backfill grouted to cut off water inflows and provide contact for equal tunnel loading which is critical in long-term design. This paper deals with an engineered backfill grouting system which was the first of its type to be used in North America. It discusses the geological conditions encountered, the design criteria used in the evaluation process, and an indepth review of the various system components. It demonstrates how contractors can use knowledgeable and professional industry suppliers to solve difficult construction problems.

Jan 1, 1999

By John Marshall

Silverton was the queen city of the western mining towns in the early 1900s. Located high in the San Juan Mountains, the town constantly grew and changed. Yet, it was subject to the vagaries and whims of economics, politics and disasters, natural or otherwise. Breweries, smelters and sawmills serviced Silverton's swelling mining population, which reached several thousand at its peak. Two trains a day ran from Durango to Silverton, in addition to trains running from Silverton over the top of Red Mountain on to Ironton. They ran up Cement Creek to the little town of Gladstone and up the Animas River Valley to Howardsville, Eureka and Animas Forks. During these prosperous times, construction flourished. There were plenty of wooden structures, and many of these stand today. The first brick buildings were built by bricklayer Patrick Stanley in 1877. It took quite a while for the first car to arrive. Almost 28 years passed from the coming of the first train to the arrival of the first car. It was brought over 3,840-m (12,600-ft) Stony Pass from Creede, CO, in an incredible journey retold years later by Louis Wyman. "Dad's daydreams were not the idle musings or the fantasies of a mystic," Wyman said. "They had a way of erupting into reality. He advocated and built good roads," he said. "During the summer of 1910, he was up to his sweatband in a project that took in half the state of Colorado. He envisioned an automobile highway, unheard of at that time, running southwest from Denver through the scenic grandeur of the high Colorado Rockies. The road would traverse a thousand miles or more of the state's finest recreational land finally circling back to Denver. Years later, when all of the county roads had been connected, it became known as 'Colorado's Thousand-Mile Circle Route.' Of course, Silverton and the San Juans were bright stars along the way."

Jan 1, 1997

By John W. Rushton

Maintenance and inventory are usually the last items considered in mine development. They need to be addressed properly and early. The micro-computer brings sophistication within the reach of even the smallest mines. Maintenance and inventory programs, if properly installed, will reduce costs 15 to 25% and allow management time to address the mining and metallurgical problems at start up. Shops and warehouses are rarely designed properly. Large engineering firms spend 5 to 20 times more than is necessary for first class facilities. There is an optimum design, size, and layout. Take the time necessary to assure you get the right people, programs, and facilities in that order. Maintenance, inventory, and inventory control must be addressed early if a small mine is to have a chance at optimizing costs during the first two years of operation. This is hard work and is usually put on the back burner until the mine is in some degree of trouble. Hiring an experienced maintenance superintendent is important but it is not the complete solution. Maintenance systems, design of facilities, and use of computers are not skills that maintenance people usually have. In addition, the work of ordering spare parts and working with erection people is a full time job and any maintenance people on site during construction are quickly recruited. The end result is that few mines start up with an adequate Maintenance or Inventory System in place. The months, and in some cases years, that the mine attempts to operate without a system are both painful and expensive. Designs of successful integrated maintenance and inventory programs are virtually 100% supported with some outside assistance. Our system is the approach that we are most familiar with and this paper will isolate how Rushton International would go about setting up systems and designing support facilities. Micro-computers are the only way for a small mine to go. ~ini-computers cost more originally and operating costs are many times higher than even the most sophisticated micro system. Micro- computer software is developed further and recent advances in hardware makes medium priced units equal to most mini's in RAW COMPUTER POWER. Mines in general, and especially small mines, have no need for main frame power. MAINTENANCE A good maintenance program has: 1. Equipment Master List a. Equipment Detail Reports 2. Work Order and Backlog Control Program 3. Component Control Program 4. Tire Program 5. Wear Materials Program 6. PM Control Program 7. Maintenance History Program 8. Performance Program We also track miscellaneous items such as MSHA training and inspections, timekeeping, etc. Rather than going through the program step-by-step, it makes more sense to go through a typical Maintenance Day and show how the programs are used. The first thing maintenance supervision needs to know is "how we are doing." We

Jan 1, 1987

By G. Potts, K. Raiber, T. BoBo

Effective control of balling line circuits is a problem taconite companies have been dealing with for over thirty years. The sensitivity of balling circuits to changes in moisture, bentonite, concentrate particle size, and other operating parameters are the main reasons for control problems. This paper presents test results and describes the integration of existing instrumentation with a digital image analysis system on a balling circuit. This work has the goal of developing control strategies to automatically adjust water spray and bentonite addition, to optimize the size distribution on the roll screen and reduce the variability in control between balling attendants, resulting in more consistent greenball product quality.

Jan 1, 2003

By R. R. Oder, R. J. Gray

We report measurements of the effects of rank, type, and grade of coal on grinding energy and grinding media consumption in a Pitt Mill. The rank of coal has a greater effect on grinding energy than does coal type. The effect of coal grade on grinding energy depends upon the relative grindability of the mineral matter and of the hydrocarbon components of the coal. The mineral matter is primarily responsible for abrasive media wear in a Pitt Mill. The widely recognized HGI test for coal breakage may yield misleading results, particularly for multiple-banded bright and dull coal where the screening procedure used in sample preparation favors the testing of the hardest coal fraction. The work reported here indicates that the Pitt Mill, which grinds the whole coal in a single stage and which yields easily interpreted results, is an excellent candidate for testing coal pulverization characteristics including energy requirements and equipment wear. The measurements of the effects of coal characteristics on grinding energy and on media consumption have been used to estimate the cost of fine grinding in a Pitt Mill. The results, based on a conceptual level evaluation of grinding at the rate of 1 TPH, show that there are trade-offs possible between the cost of energy and cost of media consumption which involve choice of grinding media size. The use of fine-size grinding media to lower grinding energy and to increase throughput can be deceptive because the total cost of grinding must consider both energy and media consumption.

Jan 1, 1992