Search Documents

By Y. S. Roditis

A new method for interpolating a block model is proposed, where both the diamond drill holes (DHs) and blast holes (BHs) data are used. Combining these data types poses a geostatistical "class size" problem due to the different statistical properties of the densely populated BHs and the sparsely populated DH data. This paper discusses how linear regression was used to adjust the DH values prior to the interpolation to account for the "class size" problem which is inherent to the procedure. The correlation between the BHs and the DHs is found. The DHs are then corrected based on the regression line. Each block that falls within a certain range of influence of a blast hole is assigned a different code and is interpolated with the combined BH and regressed DH data set. Blocks that fall outside the range of blast hole influence are interpolated using the original DH data set. A comparison against other methods, indicate a 12% improvement over using DHs only and a 2% improvement over using BHs only.

Jan 1, 1992

By Paul J. Henkels

Synthetic gypsum is the calcium sulfate co-product of a number of industrial processes. Synthetic gypsum utilization as an alternative to the naturally occurring mineral continues to grow in the gypsum industry. In particular, flue gas desulfurization (FGD) gypsum produced by the electrical utility industry has had a significant impact and a far-reaching effect on the gypsum wallboard manufacturing industry. This paper will discuss the various synthetic gypsum sources verses natural gypsum and highlight issues of use in gypsum wallboard and related products.

Jan 1, 1999

By A. G. Naguib

In essence, any magnetic separator operates on the basis of imparting a preferential magnetic force on particles of higher magnetic susceptibility which are to be separated from particles of lower magnetic susceptibility. A certain amount of directional deviation to the particles takes place thus allowing for collecting each category of particles separately. The forces in action on particles in a wet magnetic separator of the established designs can be analyzed in a simple manner as shown in Figure 1.

Jan 1, 1972

By R. David Williams

Old mine workings are found throughout the Western United Sates on lands administered by the U.S. Bureau of Land Management (BLM), U.S. Forest Service (USFS) and private lands. Some of these mine workings date back to the late 1800s. There may be as many as 100,000 sites on lands administered by the U.S. Forest Service and Bureau of Land Management. The Bureau of Land Management has worked with the State of Montana and other agencies to identify and prioritize these sites on BLM administered lands. Following completion of the AML inventory work, the Bureau began an aggressive program to clean up priority sites. This presentation will highlight completed work as well as work in progress on several sites.

Jan 1, 2000

By D. Hongjun

In this paper, the flotation rule and behaviors of kyanite-group polymerphous minerals were studied in modified Hallimond tube in detail. Furthermore, the energy change of collector/mineral systems before and after adsorption and the net charge densities of the atoms on the minerals surfaces were calculated by use of quantum chemistry. The flotabilities in minerals were successfully explained.

Jan 1, 1995

By R. L. Grayson

Following lip on a USBM-sponsored research project, the authors have utilized the knowledge-base structure and system concepts from the Sun Sparcstation-based worker scheduling system of the Mine Management Support System to develop a PC-based application. The new software adopts the nested-window concept to facilitate data collection and modification on personnel, their availability on a shift, and work priorities for a shift as well as to allocate manpower optimally on a work shift and delineate supervisory training responsibilities. The various components of the software are described in detail, along with enhancements made to the original system.

Jan 1, 1996

By J. R. Palmes

Three coal samples, selected out of eight with well characterized surface properties, were used in flocculation tests and synthetic mixture of coal and silica was used in the selective flocculation experiments. Coal wettability and flocculant type were found to have a strong effect on the flocculation results.

Jan 1, 1993

By K. Luxbacher, D. T. Hristopulos, S. Schafrik, J. Diaz, Z. Agioutantis

Big data is generated from both surface and underground mining operations. Such data contain a wealth of information concerning safety and health in the workplace and production parameters. This paper will discuss the progress towards developing an accurate forecasting model for methane gas concentration based on the analysis of data collected from Atmospheric Monitoring Systems in underground coal mines employing time series models. Several procedures need to be applied to raw data, such as data cleaning and filtering for outlier removal, data homogenization and segmentation, and exploratory statistical analysis. The data analyzed were retrieved from two coal operations in the Eastern US. A negative correlation between barometric pressure and methane gas concentration was established, at least for certain data segments. Such correlations raise the possibility that barometric pressure data can predict variations of gas concentration in the mine. The datasets will be further investigated to establish the robustness of barometric pressure and gas concentration correlation and explore the dependence of gas concentration on other factors related to mine design and operations

Mar 2, 2022

By Peter N. Loncar

Most miners dream of finding a gold mine sometime during their mining careers, but not very often do such dreams come true. On the tenth day of September, 1962, our dream of finding gold came true when the results of the third drill hole were received. This was undoubtedly one of the most exciting days of our lives. Little did we realize then that this was the beginning of a major discovery destined to became one of the largest gold mines in the country. Discovering and mining gold is not entirely new, however, to Eureka. County a old Lynn Mining District in northeastern Nevada. Since 1900 there has been sporadic activity, mostly consisting of small lode mines and placers. These have produced totally about $300,000; and existence of our orebody would probably have remained unknown had it not been for the United States Geological Survey. The USGS extensively mapped the Roberts Mountain Thrust and published a paper indicating that mineral occurred along this fault and in some places was gold bearing. Utilizing this information, our Newmont Exploration geologists located an area in which: drills were brought in to test their theories. By keeping flexible in our thinning and working, we were able to bring a raw prospect to a producing mine with ore reserves of eleven million tons in a short three-year period.

Jan 1, 1965

By S. K. Singh

"Feather edging"-a major source of injury and fatal accidents in Australia, South Africa and USA, refers to a phenomenon where the roof, at the goaf edge, falls as a thin wafer of rock often suddenly, over-riding conventional timber breakerlines. It may run down and affect adversely a working bord at distances of 15 metres or more from the goaf edge. Feather edging typically occurs in relatively massive, strong roof strata such as sandstone or conglomerate. This paper presents the results of a mine trial where a concentrated row of fully grouted bolts were able to resist the feather edging in the first comprehensive, monitored trial in an Australian pillar ('total') extraction coal mine.

Jan 1, 1999

By Erich U. Petersen

Chemical zoning studies of mineralization can be useful in guiding exploration efforts. They permit one to determine the limits of mineralization and to correlate mineralized intervals in drill holes. Fahlore minerals are well suited for zoning studies because they are common minerals found in a variety of deposits, exhibit chemical diversity, and record the chemical evolution of migrating hydrothermal fluids. Zoning information in the form of metal ratios preserved in fahlore minerals was used to determine ore body limits in the Orcopampa precious metal system, Peru, and to correlate between multiple ore horizons in a sediment hosted massive sulfide (SHMS) currently under investigation. The current generations of electron microprobes provide the most efficient, accurate and economic way to analyze the tens to hundreds of sample required to successfully describe and use zoning information at the mine scale.

Jan 1, 1991

By R. P. King

A new device, called the dual impact load cell, has been developed and built at the Comminution Center to measure fracture energy and damage accumulation in brittle particles that are subject to impact. The results show that damage accumulation during impact is not a significant factor in determining the fracture energy or the particle strength. However, predamage induced by thermal pretreatment of the particles has a significant effect on both fracture energy and particle strength.

Jan 1, 1995

By Surendra K. Mishra

With increasing regulatory pressure from the environmental authorities, waste management has become a focal point of industrial operation. To offset the waste management costs, industry has made conscious effort to recover usable resources from the waste streams. This paper reviews the technical developments and current practices in processing of waste materials. Methods for recovering metallic, non-metallic and organic species from solid wastes and effluents generated by operating plants are discussed.

Jan 1, 1997

The Mine Safety and Health Administration (MSHA) has conducted studies to evaluate dust control technologies on deep cut continuous mining sections. These surveys have been conducted in different mines using various mining methods, face ventilation systems and dust control systems. The surveys typically consist of respirable dust sampling combined with a time study of mining activities. Measurements of dust control and operational parameters are also made. Critical elements identified for controlling respirable dust in deep cut mining systems include controlling intake dust, dust collector capacity, face ventilation quantities and velocities, positioning of workers, work practices and selection of equipment. This paper discusses how the dust surveys are conducted in deep cut mining sections and how these surveys are used to identify specific dust generating sources.

Jan 1, 1999

By Malcolm D. Flavel

As indicated in the introduction to this paper, it is a sequel to that which I gave to the last annual meeting in Atlanta in march. This paper goes further into aspects of crushing and screening, primarily from the standpoint of circuit control. There has been little published by equipment manufacturers on this subject and this is the first paper on crushing circuit control to be sponsored by Allis-Chalmers corporation. By proper control over the use of crushing energy, we will be able to produce finished products from feed materials uti¬lizing minimum capital for the lowest cost of production. The subject will be discussed as follows. Firstly, we will look briefly at what we are trying to accomplish; Secondly, what is presently available in the way of technology; Thirdly, we will look at a suggested new system of control which will best fit the parameters of the normal crushing and screening operation; As a conclusion, I will summarize the advantages of the new system.

Jan 1, 1977

By S. Guo

In this paper, a model for the resin anchor bolt system is developed in which the smooth bar is modeled by using one-dimensional truss elements and the resin annulus is modeled by using axisymmetric elements. These two submodels are combined together and then incorporated into the' existing computer code ROOFBOLT. After this development, all of the components in the resin anchor bolt system including smooth bar, bearing plate and resin annulus can be correctly modeled.

Jan 1, 1995

By J. Hilgers

Metal prices are often predicted by relying on time trend projections of various economic indicators or even the trend in price itself Thus, time is the underlying explanatory variable acting through at best, a limited selection of economic variables. The price prediction method described in this paper differs from this by analyzing hundreds of economic variables to develop a few principle components that automatically capture the fundamental changes in the economy and delete duplicate or irrelevant information. This leaves a few principle variables to describe a state-space representation of the economy which can then be used for prediction. Forecasts of the price of a metal are then made based on these principle variables.

Jan 1, 1995

By W. E. Lindquist

Roasting of refractory gold ores has the primary goal of oxidizing sulfides and organics to improve gold recoveries prior to leaching. Commercial installations currently utilize bubbling and circulating fluidized beds. The principle of flash roasting is aimed at a more cost effective method of whole ore roasting for large throughput applications. Results of pilot plant testing and scale up to commercial design will be discussed in further detail in this paper.

Jan 1, 1993

By Felicia F. Peng

Using a fuzzy logic controller, a signal applied on the processes may be generated through a linguistic protocol expressing an operator's intuitive control strategies. In this work, fuzzy logic controller and PID controller imposed upon the feedback liquid level control systems for a stirred tank are studied and compared. The construction factors including the shape of membership functions, number of fuzzy variables, number of inputs, number of rules, and different defuzzification methods are considered in design and formulating the fuzzy logic control strategies and algorithms. From the analysis of the strategies and control performances, an optimum controller may be generated by making use of the best combination of these fuzzy construction factors.

Jan 1, 1997

By Chunlin He, Xinsheng Li, Feng Yang, Lu Han, Yuezhou Wei, Feng Gao

The solvent extraction of vanadium (V) from Na2CO3–NaHCO3 solution was attempted using Aliquat-336 (methyltrioctylammonium chloride) extractant dissolved in sulfonated kerosene as diluent with 2-octanol as phase modifier. The influence factors, such as Na2CO3 concentration, NaHCO3 concentration, temperature, extractant concentration and impurity P, on vanadiumextraction were investigated. The results revealed that the single stage extraction efficiency of vanadium reached above 89%from 20 g/L Na2CO3 – 20 g/L NaHCO3 solution under the following conditions: extractant concentration of 15%, room temperature of 20–30 °C, 2-octanol of 6%, phase ratio (O/A) of 1:1, and oscillation time of 1 min. The addition of NaHCO3 into Na2CO3 solution could lower the pH value of the Na2CO3 solution, improve extraction efficiency of vanadium, and not introduce other impurities. The phosphate anion did not interact with the vanadate anion in the Na2CO3–NaHCO3 solution. The P in the Na2CO3–NaHCO3 solution had little influence on vanadium extraction.

Jul 30, 2020