Search Documents

By Dal Negro Enrico, Andrea Picchio, Boscaro Alessandro

"The Doha Metro Project is one of the most relevant ongoing tunneling projects. The whole project consists of about 100 km of tunnels with 21 EPB TBMs working in the same period. Due to the variability of the geological formations, the soil conditioning is a relevant aspect of this project because the parameters should be frequently adjusted to achieve the best performances of the TBMs. The study of the soil conditioning has been carried out accurately to obtain the best results on site. The study of the geotechnical data, the choice of the most suitable foaming agents and polymers and the laboratory study of the soil conditioning has been a fundamental part of the job. The application of the soil conditioning products on site with the analysis of the TBM data have confirmed the preliminary study results with some correlation between the features of the ground and the soil conditioning parameters to be used. INTRODUCTION Phase 1 of the Doha Metro Underground project is composed by 3 lines able to bring passengers to all the points of interest in the Qatar capital city. The Red Line, also called coastal line, connects the north of the city to the south, and to the new Hamad International Airport, following the coast line. The Golden Line, called Historic Line, will connect the southern area of Doha to the “Aspire zone” the area of the city where many state of the art sport centers are located, passing through the old city center. The Green Line, named education line, will connect the old city center to the Doha Education City. All the lines are realized with 2 tubes, single track. The whole underground project is realized with 21 TBMs, excavation diameter of 7.10 m. The project has been divided in 4 packages, for a total excavation length of more than 100 km. The need to underpass roads, existing buildings, and to excavate, in some areas, at less than 100 m from the coast line, forced the choice of a tunneling system with Earth Pressure Balance (EPB), that involves in the project another fundamental aspect of this tunneling system: the soil conditioning. The soil conditioning has multiples functions in the EPB system such as to make the soil suitable to properly apply the pressure on the tunnel face and to be extracted effectively with the screw conveyor. To properly study this topic it was necessary to study the geological formations to be excavated, the hydrogeological conditions of the underground, the foam injection systems of the EPB TBMs and to perform specific tests to evaluate a suitable conditioning to be verified and adjusted during the real scale application."

Jan 1, 2016

By John Ralston, Jinming Duan, David R. E. Snoswell, Daniel Fornasiero, Jingwu Yang

The colloidal stability of synthetic silica spheres with clean, methylated and dehydroxylated sur¬faces was studied at different concentrations of dissolved gas and KCl electrolyte at a fixed pH of 4.2. A classic stability ratio/electrolyte concentration analysis shows that hydrophobic, methy¬lated particles undergo faster rates of aggregation with increasing concentrations of dissolved carbon dioxide. Similar data for hydrophilic particles and dehydroxylated particles show no change as a function of dissolved carbon dioxide concentration. Zeta potential data behave simi¬larly, showing a strong influence of dissolved gas only for methylated particles. The results are interpreted in terms of DLVO theory, with the surface-to-surface interaction dominated by the presence of very small protruding bubbles. Direct evidence for the existence of these very small gas bubbles (or "nanobubbles") was obtained using tapping mode atomic force microscopy. Small bubbles do not form on smooth, hydrophilic, or dehydroxylated silicon oxide water sur¬faces immersed in aqueous solutions under known levels of gas supersaturation. Randomly dis¬tributed small bubbles were observed over the whole surface of observation on methylated surfaces of controlled roughness. Bubbles formed on rough, methylated surfaces were larger and less-densely distributed than those on a smooth surface of similar hydrophobicity. The process of bubble coalescence was observed as a function of time. The macroscopic contact angle, measured with respect to the aqueous or gas phase, is very different from the microscopic contact angle detected by TMAFM and appears to be due to the influence of line tension at the pinned three¬phase contact line. The latter has a value of -3 x 10-10 N and acts to stabilize the small bubbles, flattening them and thereby reducing the Laplace pressure.

Jan 1, 2005

By M. Kalin, H. D. Sharma

INTRODUCTION The inactive uranium mill tailings investigated in this study are located in two mining districts, Elliot Lake and Bancroft, Ontario, Canada. The sites exhibit a mixture of surface features consisting of dry areas, with or without vegetation and areas covered with water. On the edges of the water bodies, indigenous vegetation has invaded the tailings beaches [ Typha] spp. (Tourn.) L. a dominant plant on these tailings beaches, has been studied for the uptake of radium-226 and lead-210 (Kalin and Sharma, 1981b) from the tailings. It was found that most of the radium-226 remains in the roots of the plants, and that the solubility of radium-226 in control soil differs from that in tailings. The uptake of radium226 by vegetation and other biota is related to the solubility of the element in water. Factors controlling the solubility of radium-226 in uranium mill tailings are of interest in assessing the environments effects of these wastes. Rusanova (1962) found that the soluble or extractable amount of radium from the soil is inversely related to the total concentration of calcium and magnesium in the soil. Experimental work has clarified some aspects of the leachability of radium from uranium mill tailings (Levins, et al., 1978; Wiles, 1978, and others). Halvik, et al., (1967) studied the effects of pH and chemical composition of surface water on the liberation of radium from uranium mill tailings and uranium ore. He found that an increase in pH, up to a value of pH 9, decreases the amount of radium released from the tailings and the ore. A positive effect of calcium chloride was noted on the leachability of radium. Benes (1981) reviewed the physicochemical forms of radium and its migration in water. Based on experimental work, he identifies primary factors which determine leaching of radium from uranium mill tailings. The ratio of the volume of the leaching solution to the weight of the leached sample; the composition of the leached solids and the leaching solution, and finally the pH of the leaching mixture are of importance. He emphasized that a scarcity of field data exists, which would relate experimental work to the actual situation in the tailings ponds. Inactive tailings ponds in Ontario are 16 to 23 years old, and processes which are of importance in evaluating the long term effects of uranium mill tailings in the environment can be studied. The objective of this work was to investigate the leachability of radium-226 from the tailings under field conditions. MATERIALS AND METHODS Sample Collection A description of inactive tailings sites in Ontario, where the tailings and the water for this study were collected, can be found in a report by Kalin (1981). [Typha] spp. specimens were excavated from 16 different locations along with the tailings attached to the roots of the plants. A tailings sample from the surface area, around the plant, was secured before the excavation. Tailings samples were also collected from dry areas free of vegetation in the vicinity of the wetland stand. Surface samples (depth 0-5 cm) and samples at a depth of 20-25 cm were secured. Water was collected from the shallow tailings beaches around the vegetation stands. Sample Preparation The roots of the plants were washed free of tailings with distilled water. The resulting thick slurry of tailings was allowed to settle in the wash basin for five minutes and the supernatant water was decanted. The remaining saturated tailings were brought to 400 ml volume with distilled water in a beaker. The slurry was mixed with a magnetic stirrer for two 24-hour periods. After the first 24-hours, the slurry was allowed to settle for 20 minutes and the supernatant water was removed. The remaining sediments were suspended again in distilled water (400 ml total mixture) and leached for a second 24hour period. The tailings slurries from the different locations had a solid to liquid ratio, which ranged from 0.5 to 1.4 grams of dry tailings material per millilitre. The variations in the ratios are the result of differing fractions of coarse and fine tailings on the sites. In the final leachates, the solid to liquid ratios of the samples were 0.17 (±0.1) g/ml. The pH of the surface water and the leachate was determined with an I.L. Portomatic pH meter. All the tailings samples were homogenized in a mortar and brought to dryness at 75 to 85°C. Approximately 0.5 g of tailings were

Jan 1, 1981

By Robert E. Blackett

To help local governments plan for long-term supplies of sand and gravel for buildings and infrastructure, the Utah Geological Survey is assessing natural aggregate resources (mainly sand and gravel) in the St. George, Utah area. Whereas much of the aggregate in the study area is adequate for road-base construction, high-quality aggregate for Port- land cement concrete is limited due to geology, and also due to land administration and environmental issues. Virgin River alluvial gravels southwest of St. George are generally poor sources of aggregate because they contain clasts of soft sediments and soluble minerals derived from Mesozoic rocks. Elsewhere, widespread secondary calcium carbonate (caliche), as rinds and matrix in gravel, lower the quality of material. Young river-terrace deposits in Fort Pearce Wash, and along the Virgin River above St. George are the primary sources of sand and gravel for the area. Alluvial fans on the east side of the Beaver Dam Mountains, and on the west side of the Hurricane Cliffs are also sources of aggregate. Stream-channel deposits associated with "inverted valleys" north of the towns of St. George and Hurricane, Utah, and older pediment gravels on the west flank of the Beaver Dam Mountains may be future sources of high-quality aggregate. Accelerated urban development during the 1980s and early 1990s has caused St. George and other communities in Washington County to encroach upon sand and gravel pits originally located in rural, undeveloped areas. Urban residents often view nearby sand and gravel operations as undesirable neighbors and pressure elected officials to close the pits. Pit closures effectively eliminate the remaining reserve from the sand and gravel resource base of the area. More- over, resources may also be lost as new homes are built upon undeveloped sand and gravel deposits. The St. George area is particularly susceptible to loss of aggregate resources because high-quality natural aggregate for construction is already in short supply. Moreover, most of the land in the study area is administered by the U.S. Bureau of Land Management and subject to various land-use restrictions. Much of this public land cannot be developed for mineral materials, such as sand and gravel, because of federal regulations protecting rare plants and animals, archaeological sites, and important watershed areas. Of particular concern to resource development are areas designated as Areas of Critical Environmental Concern, Wilderness Areas, and Wilderness Study Areas. Protection for Endangered Species is a critical element in all planning efforts. Those species present in the St. George area or in areas near- by include: the desert tortoise, southwestern willow flycatcher, Virgin River chub, and dwarf bearclaw poppy. As the St. George area is depleted and/or deprived of sand and gravel resources through extraction and urbanization respectively, construction costs will rise unless conservation measures are instituted. To avoid the loss of aggregate resources, the UGS is pursuing a program of data gathering and field surveying of surficial deposits to determine tonnage and quality of the remaining sand and gravel resources. The resource information from this program will help land planners, developers, and government officials make informed decisions concerning urban development throughout the region.

Jan 1, 2001

By Ivor Hawkes

INTRODUCTION High energy breaking is an alternative to using ex¬plosives in underground secondary breaking operations. It also is a means of upgrading conventional hand-held breakers, manual sledge-hammer breaking, and scaling bar operations. Major areas of application are in sec¬ondary breaking over grizzlies and at drawpoints. Other applications include breaking down ripping lips in longwall seam mining, scaling in stopes and rooms, general demolition work, and roadway maintenance. There is considerable interest in high-energy impact breakers for use in primary ore breaking, but, as of 1977, all such applications have been only experimental (duToit, 1973; Joughin, 1976; Wayment and Grantmyre, 1976). EQUIPMENT Essentially, a high-energy impact hammer is a boom¬mounted pneumatically or hydraulically actuated breaker. The machine basically consists of a piston that oscillates in a housing and impacts the end of a tool or moil thrust against the rock. The force applied to the rock primarily depends upon the impact energy of the piston-the higher the impact or blow energy, the greater the force and, thus, the greater the rock break¬age. Among drill and breaker designers, a common expression for blow energy is "force of blow." Hand-held breakers are limited to blow energies of about 140 J (100 ft-lb), because the operator is unable to handle heavier machines efficiently or to absorb the recoil energy resulting from higher blow energies. How¬ever, these restrictions do not apply to boom mounted breakers; machines with blow energies on the order of 4000 J (3000 ft-lb) and higher are available commer¬cially for underground use. There is considerable evi¬dence to show that increasing the blow energy also in¬creases the efficiency of the breaking operation; i.e., more rock is broken per unit of energy expended (Grantmyre and Hawkes, 1975). Thus, there is a trend to higher blow-energy machines, particularly where high¬strength rocks are to be broken. In relation to rock breaking, the blow rate of boom¬mounted impact breakers is not as important as it is for rock drills. This is because the breaker must be moved over the work surface between blows. The blow rate is governed eventually by the power supply, and typical blow rates range between 200 and 600 blows per minute. As a general rule, light blow-energy machines have higher blow rates than heavier machines. Table 1 lists most of the boom-mounted impact breakers that were available commercially during 1977, and it gives details of the blow energies and machine weights. Restrictions are placed on the blow energy by the machine weight and size, and by the strength of the boom. Typically, boom-mounted impact hammers have a blow-energy to mass ratio of about 1.5, with lower values for lighter machines and higher values for heavier machines. In addition to supporting the hammer weight, the boom also has to absorb the recoil energy of the blow, which can be on the order of 1400 J (1000 ft-lb) for large hammers operating in a horizontal mode. Interesting exceptions to the general run of impactors are the Joy HEFTI hydraulic hammers. In these machines, the piston impacts onto a fluid cushion that is positioned between the piston and the impact tool. This approach allows very high piston velocities, over 30 m/s (100 fps), to be used without the risk of break¬ing the piston or impact tool. Steel on steel impacts must be limited to impact velocities of about 10 m/s (35 fps) due to the high impact stresses generated; thus, increased blow energies can be achieved only by increas¬ing the piston size. The Joy 514 HEFTI®, listed in Table 1, has a blow energy of 27 100 J (20,000 ft-lb), but, as of 1977, the machine has been used underground only on an experimental basis. Using a fluid cushion between the piston and the impact tool allows the use of light pistons, reducing the overall machine weight. The recoil energy, which must be absorbed by the boom for a given blow energy, is directly proportional to the piston to machine mass ratio, and operating with light pistons provides an addi¬tional benefit in reducing the requisite boom size. Both pneumatic and hydraulic hammers are avail¬able commercially. Although hydraulic hammers are a relatively recent development, they already outnumber the pneumatic machines in use. There are many reasons

Jan 1, 1982

By N. Moony

The benefit of gravity separation in improving total gold recovery in grinding circuits has been outlined in a significant number of papers to date. However, the use of batch centrifugal concentrators (BCC) as an industry standard to extract gold has limited the potential for maximizing gravity recoveries -particularly in coarse gold deposits. This is a reflection of the high upgrade ratios obtained by BCC's which has an inverse relationship with recoveries. Survey work in Australia has indicated that installation of the InLine Pressure Jig as an alternative to the Bee will significantly increase recoveries of gold by gravity and, accordingly, increase total gold recoveries and lower operating costs.

Jan 1, 1998

By K. V. Raj

"The development and advancement of computational fluid dynamics (CFD) has made it possible to better understand pollutant flow and distribution in deep open pit mines. Open pits located at higher latitudes, especially in the Arctic and sub-Arctic, face a unique problem due to atmospheric temperature inversion, which is prevalent during much of the winter. A three-dimensional CFD model of an actual open pit mine in the Arctic was developed to analyze the problem of pollutant growth during inversion, and mitigation of the pollutants through improved ventilation schemes. Due to the availability of mine-specific data, such as contaminant concentrations and coordinates of sampling locations, the actual 2013 pit geometry was used for model validation Concentrations predicted by the selected realizable ?-e turbulent model are compared to measured pollutant concentrations at the open pit. Pollutant concentrations at selected locations showed differences, but remained within the same order of magnitude in most cases. INTRODUCTION Computational fluid dynamics (CFD) has emerged as a useful tool for ventilation modeling in underground mines (Edwards and Hwang 1999, Purushotham and Bandopadhyay 2009, Wala et al. 1998, Xu et al. 2011). Application of CFD in open pit mines has been limited, however, since most open pit mines located at lower latitudes do not encounter considerable ventilation problems. Open pits located at higher latitudes, especially the Arctic and sub-Arctic, face a unique problem due to atmospheric temperature inversion, which is prevalent during winter. A number of Russian researchers have tried to understand the air inversion and resulting pollutant transport problem by modeling air flow phenomena in open pit mines (Baklanov and Burman 1996, Baklanov 1984, Baklanov 1995, Belousov 1985, 1989, 1995). Much of their work, however, was based on numerical models and methods of finite difference. Baklanov (2000) applied a modified ?-e and a ?-l CFD model to air flow phenomena on various terrains. More recently, Choudhury (2011) used the COMSOL CFD package for modeling pollutant transport for an idealized open pit mine. Collingwood et al. (2012a, 2012b) used a two-dimensional model for fluid flow and contaminant transport at an Arctic open pit mine. The authors have also previously presented work on CFD modeling of an actual open pit mine at high latitude (Bandopadhyay et al. 2014, Raj et al. 2015a). However, the CFD work done by the above-cited researchers lacked model validation with field-measured data. Validation of a developed model is important in assessing the quality and accuracy of the predicted results. In general, experiments are done numerous times in controlled environments to assess the validity of collected data. There are two types of assessments used in CFD simulations: (1) verification and (2) validation. Model verification is checking the accuracy of the computer codes during the implementation phase of a real-world problem, within the specific limits of accuracy (Oberkampf and Trucano 2002). Since, the pollution transport model presented in this paper used the commercial ANSYS-FLUENT CFD package, verification is not needed as the program has been tested widely, and verified numerous times."

Jan 1, 2016

By Walter C. Labys, William A. Vogely, David O. Wood

INTRODUCTION The past decade has witnessed a literal explosion in formal modeling of energy systems and markets. This rapid development was stimulated primarily by policy issues arising from the energy price shocks of 1973- 1974 and 1979- 1980. The suddenness of this interest is illustrated by comparing the current and earlier editions of Mineral Economics. The third edition, published in 1976, includes an addendum to the section of projection and forecasting methods because, Since the foregoing chapter was written, major events in petroleum have caused an explosion in formal modeling efforts in the energy field.a In contrast, this fourth edition includes the present chapter on energy modeling, and a separate chapter on nonfuel minerals modeling. The considerable interest in formal energy models is based on the complexity of the system, in particular the interaction between technical and engineering data and designs, and economic behavior of energy producers and users. Energy is a vital component in the economic and social well-being of nations, and must increasingly be explicitly considered in developing economic growth and welfare policies. Energy models can contribute to policy development and analysis, both by improved understanding of the energy system, and of the interaction between energy markets and the economy, and as an explicit means of analyzing and comparing the implications of alternative policy actions. At their best, formal models can clarify and illuminate policy options. In this chapter we will survey the objectives, methods, and potential contributions and limitations of energy system modeling. Section 2 considers the objectives, scope, and approaches to energy system and market modeling. Methodological approaches are then discussed more formally in section 3. Our approach is to intro- duce each model type and method via relatively simple generic models, illustrating their use by a selective review of the applications literature. Section 4 shifts the focus from modeling methods to procedures for model evaluation and improving model credibility especially in policy research and analysis. We conclude with some brief remarks on directions and opportunities for future modeling research. ENERGY MODELS: OBJECTIVES, SCOPE AND APPROACHES The concept of a model usually evokes an image of a complex, computerized system of mathematical or econometric equations providing detailed information concerning the operation of the process being modeled. In fact. models may be simple or complex, formal or mental, depending upon the purposes for which the model is intended. Simple judgmental models may be most appropriate when monitoring the overall performance of a process. When more detailed information is required and/or when the model

Jan 1, 1985

By Bernard F. Anderson

INTRODUCTION In this chapter, the term "down-the-hole drill" (DTH drill) is used as a generic name that encompasses the various trade names and other references such as "downhole drill," "in-the-hole drill," etc. This chapter is limited to a description of DTH drills used in stoping large underground ore bodies. DTH drills differ from conventional drills by virtue of the placement of the drill in the drill string. The DTH drill follows immediately behind the bit into the hole, rather than remaining on the feed as with ordinary drifters. Thus, no energy is dissipated through the steel or couplings, and the penetration rate is nearly constant, regardless of the depth of the hole. Since the drill must operate on compressed air and tolerates only small amounts of water, cuttings are flushed either by air with water-mist injection or by standard mine air with a dust collector at the collar. HISTORICAL DEVELOPMENT Mine managers have long known the economies enjoyed by quarry and open-pit operators in producing large quantities of ore. The savings are due primarily to the availability of massive equipment, capable of drilling large blastholes to reduce the amount of drilling, increase the fragmentation, reduce secondary blasting, and im¬prove the flow of the product. In an attempt to reduce underground mining costs, various methods are used for long-hole drilling, includ¬ing standard pneumatic percussion drifters and diamond drills. These systems have their shortcomings; percus¬sion drills are limited to small hole sizes and they ex¬perience excessive deviation and significant loss of energy with increased depth. The diamond drills provide deeper and straighter holes, but only at high cost. Both systems suffer from high noise levels, low penetration rates, and poor explosives distribution, among other problems. When the mining companies approached the drill manufacturers for a compact and portable large-hole jumbo for underground use, they specified not more than 1 % deviation on 60 m (200 ft) of vertical hole and a penetration rate of 15 m/h (50 fph). On Dec. 23, 1960, a test unit was placed in service in Montana and met the performance criteria. Though lacking the so¬phisticated features available today, the economies of surface blasting were brought underground. Unfortunately, the first system did not gain immedi¬ate acceptance in the industry. Among the factors con¬tributing to its demise were resistance to change, the need to alter development methods for the ore bodies, and a lack of flexibility in moving the rig from setup to setup and from level to level. In 1972, the mining industry again challenged the drill manufacturers to provide a workable jumbo that would combine compactness, ease of maintenance, relia¬bility, and efficiency, all on a self-propelled chassis. The manufacturers responded by providing improved jumbos, which have been accepted with enthusiasm throughout the mining industry. Today's DTH jumbos are capable of drilling from 100 to 200 mm (4 to 8 in.) diam holes that can be reamed to even larger diameters. The holes can be drilled to depths of 150 m (500 ft), depending upon ground conditions and the capability of the jumbo to retrieve the steel and drill. Fig. 1 illustrates a typical DTH jumbo. APPLICATIONS The uses to which DTH drill jumbos have been put are quite numerous, with new uses being found regularly. For convenience, these uses may be classified as primary blastholes and nonblasting holes. Primary Blastholes The original purpose for the development of the DTH jumbo was for drilling primary blastholes that could be mined by open-stope methods. Prior to the advent of the DTH jumbo, extensive development was required before production drilling could begin. Sub¬levels were required to allow access for column-and-arm stopers or ring/fan jumbos, to the extent necessary based on the effective penetration of the chosen machine. With the DTH jumbo, the mine engineer is able to reduce preproduction time and development costs. How¬ever, the most significant saving results from an im¬proved cost per ton of broken ore in the production phase. To utilize a DTH system, only a top heading and drawpoints are necessary. The top heading can be the width of the ore body with a 3.7-m (12-ft) back. A drop-raise pattern is drilled and shot to begin the stoping operation, providing a free face for subsequent blasting. A typical layout is illustrated in Fig. 2. The advantages of this system include: 1) Drilling and blasting are independent operations, and blasting can be performed at a rate congruous with the mine's ton-per-day capacity. 2) The development layout is simplified. 3) Good explosive distribution is achieved, provid¬ing more uniform fragmentation. 4) Environmental conditions for operators are im¬proved, including improved safety with all work directed downward (not overhead), lower noise levels, little fog, and a reduced dust count. 5) Improved production per manshift. 6) Simplified and easier operator work cycles. 7) Reduced cost per ton of product. 8) Fewer holes lost due to ground shifts. Nonblasting Holes With the introduction of the compact DTH jumbos, other practical uses became apparent, including the drilling of: 1) Holes for sand fill, from level to level and from level to stope. 2) Drain and dewatering holes. 3) Power and communications cable holes.

Jan 1, 1982

By James M. Barker, George S. Austin

Stone, one of the oldest building materials, today remains a well-established material throughout the construction industry. The use of natural stone is much less prevalent now than in the past. It is still widely considered to be the most aesthetically pleasing, prestigious, and durable building material. New and re-opened quarries are coming onstream to meet increased demand related to new building technology and increased residential use of stone. CLASSIFICATION No classification can completely eliminate overlap between dimension stone, aggregate, and decorative stone because most stone is multi-purpose. Many used for decorative purposes are not produced specifically for that end use. Rock otherwise considered waste in dimension stone or aggregate quarries can be decorative stone coproducts (Fig. 1). Many uses require a compromise between decorative and structural qualities (Bowles, 1992, written commu¬nication). Shipley (1945) used decorative stone interchangeably with or¬namental stone. Gary et al. (1972) defined decorative stone as that used for architectural decoration, such as mantels, columns, and store fronts, but added that it is sometimes set with silver or gold in jewelry as curio stones. Bates and Jackson (1987) also restricted decorative stone to that used for architectural decoration. Meanings of otherwise identical terms used in the stone industry differ be¬tween geologists, engineers, and quarriers. They often carry a much broader meaning for quarriers and engineers compared to their very specific use by geologists (Makens et al., 1972). Decorative stone, including ornamental stone, is more broadly defined by geologists as any stone used primarily for its color, texture, and general appearance. It is not used primarily for its strength or durability, such as construction stone, or in specific sizes, such as dimension stone. The decorative stone industry uses a much wider range of stone types compared to stone that is dimensioned. Decorative stone usually serves some structural pur¬pose, but is not load-bearing to any great extent. Weak or costly stones serve in decorative, not structural, applications. STATISTICS AND END USES Decorative and dimension stone data are difficult to separate because the US Bureau of Mines keeps statistics only on dimension stone and crushed stone. The value of domestic dimension stone production in 1990, which includes some decorative stone, was about $210 million compared to imports of about $524 million and exports of about $35 million. Production was 1 080 t of which at least one-third was for decorative uses (Taylor, 1992). The principal uses are rough blocks in building construction (23%) and monu¬ments (18%); the remainder is used as ashlar (18%), curbing (12%), and miscellaneous (29%). Major rock types are granite (50%), limestone (30%), sandstone (10%), slate (3%), marble (2%), and other (5%) (Harben, 1990). Crushed stone valued at $5.6 billion was produced in the United States in 1990 by 1700 companies operating 3400 active quarries in 48 states (Tepordei, 1991). About 52% is used in con¬struction, 9% in cement and lime manufacturing, 2% in agricul¬ture, 2% in industrial uses, and 35% for unspecified uses including decorative aggregate. Limestone and dolomite comprise about 71%, granite 14%, and traprock 8% of the stone crushed in the United States. The remaining 7% are, in descending quantity, sandstone, quartzite, miscellaneous rock, marble, shell, calcareous marl, volcanic cinder and scoria, and slate. The basic types of decorative stone are: rough stone, aggregate, cut or dressed stone, and manmade stone [(Table 1)]. Rough Stone Rough stone is used as it is found in nature with very limited processing such as minor hand shaping, edge fitting, and size or quality sorting (Perath, 1992, written communication). This stone type is often marketed locally in relatively small tonnages and includes fieldstone and flagstone. The primary end uses of rough stone are landscaping, edging, paving, or large individual stone landscape or interior accents [(Fig. 2)]. Fieldstone: Fieldstone is picked up or pried out of the ground (gleaned) without extensive quarrying and includes garden or large landscaping boulders (Austin et al., 1990, Hansen, 1969). Boulders and cobbles may be split or roughly trimmed for use in rubble walls and veneers, both interior and exterior. Popular fieldstone rock types include sandstone, basalt, limestone, gneiss, schist, quartzite, and granite, but many others are suitable. Much fieldstone is col¬lected by individuals or small companies because the industry is labor intensive and markets are small. The stone may be sold locally in small quantities from the back of vehicles (Austin et al., 1990). Fieldstone includes many rock types, sizes, and shapes with the only common denominator that it must be set by hand and be durable (Power, 1992, written communication). Moss Rock. Moss rock is fieldstone partially covered by algae, mosses, lichens, and fungi that give the rock an aged and variegated patina (Austin et al., 1990). The plants are supported by moisture and nutrients in the stone. Moss rock is used for landscaping, walls, and fireplaces. Although almost any durable rock can be a moss rock, most are slabby or rounded sandstone and limestone (Fig. 3). Flagstone: Flagstone or flagging consist of thin irregular slabs used for paving, walkways, and wall veneers. Random-shaped flagging is produced widely in the United States. Suitable stone

Jan 1, 1994

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

4.1 THE GENERAL COMPOSITION AND PROPERTIES OF CLAY-BASED GROUTS Clay-based grouts are visco-plastic systems; they are made by adding structure-forming reagents to a clay mineral mortar. Small amounts of cement and various chemical ad¬ditives constitute the reagents. If necessary, fillers also are added. The distinguishing feature of clay-based grouts is that throughout their entire stabilization period they do not form a crystallized structure as does cement grout. The structure of stabilized clay-based grouts does not deteriorate during minor rock movement or upon the initiation of blast¬ing during the construction of a shaft or a drift. Because they can possess good rheological properties during the ini¬tial structure-forming period relative to cement grouts, clay¬based grouts are not easily eroded from large fractures and karstic cavities by flowing ground water. In addition, their finely dispersed clay particles facilitate a greater fracture penetration capacity, especially in dual porosity rocks. Numerous investigations of the structural-mechanical and rheological properties of clay-based grouts by STG have demonstrated that the most effective grouts for pre¬venting the inflow of ground water into underground work¬ings are grouts that have a cement content of 8 to 10% (90 to 120 kg/m3) of the clay grout by mass. The grout should have a density of 1.18 to 1.30 T/m3. Various additional substances and chemicals can be added as additional fillers and structure-forming reagents. In pure ground water at temperatures above freezing, sodium silicate in the amount of 0.8 to 1 % by mass normally is the only structure-forming reagent that is necessary if the proper clay is selected and if it is available. The production process for making clay-based grout is divided into two stages: 1) the production of an initial clay mortar with specified properties and 2) the production of a clay-cement additive grout mixture using the initial grout along with the structure-forming reagents, including the ce¬ment. The properties of clay-based grouts depend on the phys¬ical-mechanical properties of the initial clay mineral, the properties of the cement and the properties of the chemical reagents that are added. 4.1.1 TECHNOLOGICAL PROPERTIES OF CLAY-BASED GROUTS The dynamic shear stress' To, the viscosity 11, the static shear stress2 0, the maximum shear stress of the structured that the rheological and structural-mechanical prop¬erties of clay-based grouts must fall within the following limits: the dynamic shear stress To = 50 to 200 Pa; the viscosity -9 = 0.02 to 0.07 Pa sec; the static shear stress 0 = 150 to 600 Pa; the plasticity strength Pm of the structure one minute after preparation (according to P.A. Rebinder's method) equals 150 to 500 Pa. The plasticity strength 10 days after preparation is ? 0.15 MPa. The general relationship of the change in the structural strength of clay-based grouts relative to stabilization time is shown in Fig. 32. The figure shows that the structure-form¬ing process for clay-based grouts is characterized by three stages. These stages correspond to the time periods required for conducting the principal operations during the injection of the grout into a fractured aquifer as described below. Stage I, corresponding to the time period T1, reflects the small development of structural strength during early stabi¬lization. During this time, the structural strength must not preclude the capability to pump the grout. The time Tl must correspond to the length of pumping time from the moment water is shut off and mixing occurs until the pump stops forcing the grout through the manifold block and pipeline into the fractured rock as described subsequently herein. Stage II, corresponding to the time interval T2, reflects a sharp but controllable increase in the structural strength of the grout. The length of time period T2 is controlled by the addition of appropriate reagents. Stage III produces the final value of the structural strength. This final strength is used to design the dimensions of the isolation curtain. Consequently, the development of grouts is guided by two principal criteria: 1) the grout must develop the highest possible structural-mechanical properties and 2) it must be able to be pumped by a piston pump prior to final stabili¬zation. Successful grouting depends to a large extent on the correct design of a grout for each specific case. It is impor-

Jan 1, 1993

By Robert C. Freas

Lime, the versatile chemical is, generally speaking, a calcined or burned form of limestone commonly known as quicklime, calcium oxide or, when water is added, calcium hydroxide or slaked lime. Almost 40 different lime products are available, a fact which has contributed to the rather loose use of the term lime as well as to confusion and misunderstanding. The term is frequently, albeit erroneously, used to denote almost any kind of calcareous material or finely ground form of limestone or dolomite. Lime is made from high calcium or high magnesium limestone, generally having a minimum of 97% combined carbonate content. Normally, high calcium lime has less than 5% MgO. When the lime is produced from a high magnesium limestone, the product is referred to as dolomitic lime. Calcination/Hydration Calcination, or the production of lime, has its origins in the earliest days of alchemy, with the general reaction class having been identified in an Arabic text printed in 1000 AD. It was much later, however, in the mid-1700s to the mid-1800s before this basic reaction became understood from scientific perspective. The pro- duction of lime has been so basic and simple that its underlying scientific principles have over the years received only intermittent investigation. Rather, much of the thought and inquiry has been directed toward the development of kilns. Thus, it has only been in the last 25 to 30 years that lime has received any concentrated scientific investigation relative to the thermodynamics and kinetics of the calcination and hydration reactions. Particular emphasis has been focused upon energy consumption and fuel efficiency. Calcination refers to a broad class of reactions, of which the limeflimestone reaction is just one, wherein a substance is heated to less than its melting point, resulting is a weight gain or weight loss. In the calcination of limestone to produce lime, the basic chemical reaction is as follows: [ ] While there is nearly universal agreement bout the equilibrium conditions related to the limestone/lime reaction above, there have been numerous and varied calcination models developed for the reaction. Recent investigations have resulted in the development of the model shown in [Fig. 1]. From this model it can be seen that calcination is a function of both temperature and CO, pressure. It does not, however, provide any indication of the rate at which the reaction takes place. Calcination is strongly time variant with different limestones. In a very broad sense this relates to the fact that the calcination reaction starts on the exterior surface of the limestone and then proceeds toward the center. As the calcination reaction takes place, the CO2 released at the interface must make its way through the lime to the exterior surface. Since calcination is limited by gas diffusion to the surface of the partially calcined limestone, the natural impurities in the stone, differences in crystallinity, grain boundary chemistry, density variations, and imperfections in the atomic lattice all play a significant role in calcination rate. Therefore, the suitability of a given limestone as a source material for lime production can be determined only after completion of adequate burn tests designed to evaluate the various limiting factors. When a coal-fired kiln system is considered, the entire process of calcination is made even more complex by the introduction of additional chemical constituents into the calcination environment. The reader is referred to the references for a more detailed description of the complete calcination reaction and the differences inherent between differing kiln systems. In the foregoing discussion it was noted that CO2 is released during the reaction. This release results in a 44% weight loss during the complete calcination of a high calcium limestone, or a 48% weight loss for a highly dolomitic limestone. The trade term for this weight percent loss is loss on ignition, or LOI. This weight loss is frequently used as a measure of the completeness of calcination. Because the calcination reaction is chemically reversible, quicklime or burned lime is frequently referred to a being highly reactive, or unstable. The more stable form of lime, hydrated lime, is commonly preferred and generally specified by the user. Hydrated lime is obtained by adding water to quicklime to produce a dry, fine powder. Quicklime's affinity for moisture is then satisfied, although it still retains a strong affinity for CO2.

Jan 1, 1994

By B. J. Scheiner

The Bureau of Mines, U.S. Department of the Interior, has investigated the use of rheology to provide insight into the mechanism of flocculation. A technique developed by Tattersall has been modified and used to explain the flocculation of calcium montmorillonite with polyethylene oxide. The results indicated that there are two types of bond systems operating during the flocculation sequence. Also, flocculation results are highly dependent on the shear rate and the amount of polymer added.

Jan 1, 1989

By Jr. Neudecker

Rock melting technology can provide in-situ glass liners in nuclear waste package emplacement holes to reduce permeability and increase borehole stability. Reduction of permeability would reduce the time and probability of groundwater contacting the waste packages. In-creasing the stability of the storage boreholes would enhance the retrievability of the nuclear waste packages. The rock melting hole forming technology has already been tested in volcanic tuff similar to the geology at the proposed nuclear waste repository at Yucca Mountain, Nevada.

Jan 1, 1989

By Frank F. Aplan

Introduction Heavy media separation (HMS), also called dense media or float¬sink separation, is one of the newer forms of gravity concentration. Though the concept can be traced to the last century, the process has enjoyed its major growth since 1940. Heavy liquid separation is a mutation. The heavy media process is used extensively to clean coal and for the concentration of a wide variety of ores such as those of iron, lead-zinc, chrome, manganese, tin, tungsten, fluorspar, magnesite, sylvite, garnet, diamonds, gravel, etc. It may be used where ever a significant density difference occurs between two minerals, and commercial separations are typically made in the range of 1.3 to 3.8 sp gr. The particle size treated ranges downward from 6-8 in. top size. Particles greater than about 1/16-in. (10 mesh) may be treated in a "static" bath, though for reasons of separation efficiency, + 1/2 -in- feed is usually preferred. For particles less than this size, separation in a heavy media cyclone is generally used. The flowsheet of a typical heavy media process, in this case one using a ferrous medium, is shown in Fig. I. In essence, the process consists of: (1) preparation of the feed usually by wet screening to remove undesired fines, (2) heavy medium separation, and (3) removal and recovery of the medium from the separated products. Many muta¬tions of the basic scheme are possible and numerous options are possi¬ble. HMS offers the following potential advantages:12 1) Ability to make sharp separations. 2) Ability to change the specific gravity of separation quickly to meet changing conditions. 3) Ability to remove products continuously. 4) Ability to treat a broad size range of products. 5) Ease of start-up and shutdown without loss of separating efficiency. 6) Relatively low medium cost and low media losses. 7) Low operating and maintenance costs. 8) High capacity with the use of relatively little floor space. 9) Relatively low capital investment per ton of capacity. The process may be used to produce a finished concentrate, two finished concentrates, or a concentrate and a middling of differing quality, or a preconcentrate by rejection of unwanted gangue. It is an ideal method for the reprocessing of coarse waste dumps. The greatest use for the process lies in coal cleaning and in the preconcentration of ores. The relatively inexpensive heavy media process may be used advantageously to reject large quantities of coarsely crushed gangue. When used in this way, the process will allow: (1) the use of lower cost but less selective mining methods with the "overbreak" material being removed at the front end of the concentrator or preparation plant; (2) a substantial reduction in the quantity of ore that must be finely ground for subsequent mineral liberation and separa¬tion. Since comminution is often the single most expensive step in beneficiation, it is desirable to eliminate as many essentially barren pieces of rock as possible before the grinding step, (3) a decrease in overall plant capital cost per ton of concentrate since the size of the plant from the dense medium step onward will be smaller. Several general references are available,12-18 though much of the technical data on the process is widely scattered in the general litera¬ture. Heavy Liquid Separation Organic Liquids Given sufficient settling time, it is possible to make a perfect separa¬tion between two particles of differing density by placing them in a liquid whose density is intermediate between the two. This means of achieving a perfect separation has proven to be elusive because of problems in feed preparation, particle settling rates, operational considerations, and economic constraints. There are a wide variety of heavy liquids that could be used, most of them halogenated hydrocarbons, and a few typical examples are given in Table 4. These liquids are most commonly used in ore dressing for the laboratory fractionation of ore particles on the basis of specific gravity. Laboratory Separations. Using liquids typified by those given in Table 4, separations are made to develop either the standard washability curves used to estimate the response of a given sample to gravity concentration or to prepare a partition curve to evaluate the effective¬ness of a given gravity separation process or piece of equipment. A typical washability curve is given in Fig. 2.19 Such curves are generated for raw coal, e.g., by treating either the whole or various size fractions of the sample in a series of heavy liquids and analyzing the various specific gravity fractions so produced. The procedure is relatively simple for coal samples because of the ready availability of a wide variety of relatively low cost heavy liquids in the density range 1.2¬-2.0. For ores the problem is much more complicated, because only a few high density liquids, all of rather high cost, are available. Parti¬tion curves are generated in the same manner by treating the separated products in the same liquids. Greater details on the procedures to be used in heavy liquid separa¬tions are to be found in the literature (for coal, Refs. 13, 14 and 19 and for ore, Refs. 20 and 21). For testing coal, calcium and zinc chloride solutions have been used extensively in the past, though today halogenated hydrocarbons (available under the trade name Certigrav) are the preferred media. The liquids shown in Table 4 may

Jan 1, 1985

By R. E. Miller

Accelerometers and pressure transducers mounted in suspension components can be used to monitor the ride of haulage trucks. Presently, it is difficult to tell what caused a jolt to the truck using either pressure or acceleration data alone. When information from a Global Positioning System is recorded at the same time as shock pressures or acceleration data, then the exact location of an event can be determined. Mine management can then determine what caused the jolt to the truck.

Jan 1, 1999

By J. Frenzel

The computation of hydrometallurgical equilibria is very difficult because of the many complex species in solution, the precipitates, condensed species, or solids, and the activity coefficient corrections necessary to non-ideal thermodynamics. Our objective was to tryout recently developed genetic algorithms to minimize free energy and solve the equilibrium computation. We selected test problems that were seemingly unsolvable with more traditional algorithms, and we applied genetic algorithms to them. We were pleased to find that genetic algorithms succeeded where other algorithms did not. We concluded that they are an effective tool for hydrometallurgical equilibria.

Jan 1, 1992

By J. R. Koehler

Mining practices at the Sunnyside Mines, Sunnyside Coal Company, Sunnyside, UT, have been documented by U.S. Bureau of Mines researchers to preserve the extensive history of yield pillar-based longwall gateroad system evolution on the property. An overview of the historical mining conditions, practices, and innovations that resulted in the evolution of the two-entry yield pillar gateroad system currently employed at Sunnyside was developed from interviews of 30 long-time Sunnyside employees. Employing yielding chain pillars at Sunnyside virtually eliminates tailgate pillar bumps and contributes to reducing face bumps. Limiting the overall width of the gateroad system benefits bump control and especially, roof and floor stability.

Jan 1, 1994

By Stephen V. Thompson

Within recent years portable seismic refraction units have found their place in the industry for shallow investigations, Completely portable, relatively inexpensive and of proven accuracy, the portable refraction seismograph is an electronic tool in an electronic age. The age of electronic instrumentation has seen the development of seismic reflection and refraction equipment for deep exploration, especially in the petroleum industry. Large, expensive units, normally truck-mounted and utilizing explosives, are being used successfully for this type of sub- surface investigation. The portable seismograph utilizes the same theory for shallow work as that applied to deep refraction seismology.

Jan 1, 1964

By B. S. Crocker

Introduction Pebble mill grinding can be defined as wet or dry grinding in a tumbling mill with pebbles used as grinding media instead of metal balls. To clarify the terminology, which may differ in the various mineral industries, it is essential to point out the differences between grinding with partially sized and carefully sized grinding media. When grinding with partially sized media (limited top size only), sizing is usually the setting of the primary crusher and there is no bottom sizing-all fines, chips, sand, and small sizes are included. This is often called run-of-mine or primary autogenous grinding. In this case the entire crusher discharge is fed into the mill and part of it becomes "charge" and the rest is "sand feed." When grinding with carefully sized media (i.e., media that is sized both at the top and bottom of the size range), no fines or chips should be present in the charge to the mill. This is pebble milling and the grinding media consists of ore, rock, Danish pebbles, gravel pebbles, or ceramic pebbles-media that is appreciably lighter than steel balls. The grind¬ing charge is fed to the mill to maintain a load and it does the grinding usually on a classified sand product of suitable size. If the grinding media is the same as the raw material being ground, this type of grinding is also called secondary autogenous grinding. Pebble milling was in common use in the gold mines of South Africa in the early 1900s. It is by far the oldest form of autogenous grinding. It may be used to grind crushed ores from a maximum size of about -% in. to all -10 µm. Pebble milling differs from "run of mine" grinding in many ways, but two big differences are: I) The ore itself is crushed to approximately t/4 in., or it may be further reduced to 8 or 10 mesh in a rod mill or fine crusher. 2) Then carefully screened ore of the correct size is placed in one or more stages of pebble mills to grind the ore to its desired final size. The media size is carefully selected to be the most efficient for the particular size reduction required in each stage. This is a precise practice, and pebble mills can be designed as easily and accu¬rately as can rod mills or ball mills by those skilled in the art. A pebble mill is a rotating cylinder in which the grinding media has been carefully sized for the job in hand. If the mill is doing coarse grinding, the media will be correspondingly large and the mill might be called a primary (or intermediate) pebble mill or a lump mill. If it is to do fine grinding, the media selected is proportionately smaller and the mill would be called a secondary or tertiary pebble mill. The media itself is normally rounded pebbles made from screened ore from the primary-crusher discharge. The charge could be rounded pebbles of the correct size removed from a primary autogenous mill, or the pebbles could be carefully sized gravel, sized beach pebbles, or sized flint pebbles. Usually the specific gravity of a pebble is from 35 to 55% of that of steel balls. It commonly varies from 2.66 to 4.2, depending on the specific gravity of the ore. Primary pebble mills, or lump mills, would be charged with pieces of rock up to 10 in. maximum and 5 in. minimum and would grind crusher discharge with a maximum size of 1/4 in. on hard ores and 3/8 in. on softer ores. Secondary pebble mills could be charged with pieces of rock screened on 4 x 4-in. square mesh and retained on 1 1/2 x 1 1/2 in. These mills would grind material with a top size of 8 to 10 mesh. Tertiary pebble mills could be charged with screened rock that would pass 3 x 3 in. and be retained on 1 x 1 in. and grind 35 to 48 mesh sands. Principles of Operation Media Size To operate a pebble mill efficiently it is imperative that great care be taken in screening the rock feed that is fed into the mill to round up into a range of pebble sizes that are suitable for grinding of the sands that are also being fed into the mill, having regard to the top size and the average size of such sands. Since most mill operators know from experience the correct size of steel balls to be used in a mill to handle different sizes of sand feed, it is convenient to relate the pebble size to a ball size. If the correct ball size is not known, it is relatively simple to conduct batch laboratory tests in 12- to 18-in. laboratory mills to determine the optimum size of steel ball. Also, Bond and others have published formulas for calculating the optimum ball size. When the correct size of the individual steel ball is known, then a pebble of the same weight will perform the same grinding if used in the proper size of mill and under the proper conditions, which will be defined later. This media size, as defined by the average weight of the individual pieces, is most important. The following tests will serve to clarify this point. Laboratory Tests Using Steel Balls or Pebbles. Several labora¬tory grinds were made to compare a given size and weight of steel ball with a pebble of the same weight but larger size, and of the same size but lighter weight. The following loads were used in the 12-in. laboratory mill: All 1 1/4-in. steel balls weighing 122 ± 10 g. All 1 3/4-in. pebbles weighing 123 ± 5 g. All 1 1/4-in. pebbles weighing 45 ± 3 g. To equalize capacity, the test with the steel balls was run only 34% as long as the tests with pebbles. In each case, 2,500 g of primary sands were ground at the optimum gravity for the media being tested at a speed 78 1/2 % of critical speed, and for 170, 340, and 680 revolu¬tions for the steel balls, and 500, 1,000, and 2,000 revolutions for the pebbles. The first test is summarized in Table 74 by showing the 80% passing size in microns for the feed and for each of the grinds. Two other tests are summarized in Table 75 showing the screen analyses

Jan 1, 1985