Search Documents

By William Petruk, J. H. Gilles Laflamme, Jean Robitaille, Louis J. Cabri

"A quantitative mineralogical study using ore microscopy, electron microscopy, proton-microprobe, image analysis, and material balances was done on samples from the circuit of a concentrator in Quebec, with particular emphasis on the Cu concentrate. The ore contains many different minerals, of which the principal ones, in decreasing order of abundance, are pyrite, sphalerite, chalcopyrite, bornite, galena, tennantite, and pyrrhotite. Minor to trace amounts of covellite, chalcocite, stannoidite, mawsonite, colusite, wittichenite, miharaite, hessite, petzite, electrum, and an unidentified Cu-Pb-Bi-sulfide also occur.Liberation of pyrite is very high in all size fractions for all samples (ranging from 80-91 %). Liberation of chalcopyrite, bomite, sphalerite, and tennantite is relatively high, on average, in the head .sample and Cu concentrate (55-78% and 66-88%, respectively). Most of the chalcopyrite in the flotation tails is not liberated, whereas about one half of the tennantite and sphalerite are liberated in both the flotation and :final tails. Recoveries calculated for the Cu concentrate (on the basis of assays, mineralogy, and image analysis) are chalcopyrite 72. 5%, bornite 73. 7%, sphalerite 41.0%, tennantite 70.9 %, and galena (together with some trace minerals) 34.2%. It was also calculated that the Cu concentrate contains 10.0 % of the pyrrhotite and i.4 % of the pyrite.Materials balance calculations were done on the five major sulfide minerals to determine the mineralogical distribution of 13 major, minor, and trace elements (as determined by protonmicroprobe analyses). It was determined that tennantite is the principal carrier of Bi (67%), As (90%), and Te (86%) in the Cu concentrate. Therefore, removal oftennantite, which is mostly liberated in the Cu concentrate would significantly reduce these three contaminant elements, but at a loss of9% of the Cu, 2.0% of the Zn, and 0.7% of the Ag. The precious metals (Au, Ag) occur as discrete minerals (electrum, petzite, hessite). Some of the Ag also occurs in solid solution in bornite (23.1% of Ag in Cu concentrate), tennantite, and sphalerite. Four of the major sulfides (chalcopyrite, bomite, sphalerite, tennantite) in the ore also contain measurable concentrations of the following trace elements: Se, Cd, In, Sn, and Sb, occurring mostly as solid solutions. Some of these elements are also concentrated (up to about 18%) in minor and trace minerals such as colusite, stannoidite, and mawsonite."

Jan 1, 1999

By Jesús Contreras

Since the commencement of its activities in Huelva in 1970, Atlantic Copper has maintained a course of action that has been more demanding than the successive environmental legislations current at different times. As its primary objective it has sought compatibility between the protection of the environment and both its industrial activity and the social and economic development of the area in which its Metallurgical Complex is located. For this reason, since the seventies it has maintained a continuous programme of investments which have allowed it to attain its present environmental situation. As a consequence of the Environmental Policy of Atlantic Copper, in April 1998 it obtained certification for its Integrated System of Environmental Management (SIGMA) according to international standard IS0-14001, and under European Community Regulation 1836/93 (replaced by the 76112001) for the Eco-Management and Eco-Audit System (EMAS). The SIGMA formalises the environmental management practices of Atlantic Copper and engages it to have available a system that can be fully audited. Atlantic Copper was the first European Company in the non-ferrous metallurgical sector to obtain both the UNE-EN-ISO 14001 certification and the EMAS registration. The present paper reviews the actions by Atlantic Copper in environmental matters that have allowed it to achieve its present position. It also describes the coming stages of improvement planned and the modifications to be carried out in the near future, in particular the criteria for the selection of technologies on the basis of the concept of BAT (Best Available Techniques) introduced by the European Union, and always guided by the final objective of converting Atlantic Copper into a reference within the sector, comparable to the best designed and operated installations in the world.

Jan 1, 2003

By Francis C. Furman

Microscopic evidence indicates that the high sinterability of certain commercial dolomites is tied to specific dolomite textural characteristics. This study encompasses detailed characterization of the unprocessed dolomite and sintering doloma results. The chemical and mineralogical compositions, insoluble residue, chemistry homogeneity, crystal size, primary carbonate texture, secondary dolomite texture, deformation structure, porosity type, porosity, and density of the raw dolomite were observed. These characteristics are compared with sintering trials of <74um powder-compacts samples in which holding times were varied. The evolution of the dolomite characteristics are reviewed and related to the final sintered doloma characteristics. The critical characteristics of a single-stage sintering brick dolomite are the following: 1) primary oolitic texture, 2) dolomite purity, 3) dolomite stoichiometry 4) minimal impurities, less than 1 weight {%} Fe2O3 Al2O3 and SiO2, 5) chemical homogeneity, 6) high density, 7) very low porosity, S) very coarse homogeneous crystallinity, 9) nonplanar dolomite texture, 10) abundant strain related slip microdeformation structures, 11) minimal subsequent alteration. Even with grinding to <74um the nonplanar dolomite texture and slip deformation still have a major effect on doloma sintered density. The three newly identified characteristics of single-stage sintered refractory brick dolomite are their primary oolitic texture, secondary nonplanar texture and abundance of stress related microdeformation structures. The primary oolitic texture reflects a homogeneous pure carbonate with respect to chemistry and crystal size secondary nonplanar texture produces crystals with large surface area to volume ratio. Stress related slip deformation moves CO, groups in to the same site of another CO, group but different orientation which is very unstable. All of these characteristics may facilitate the formation of higher density dolorna sinters.

Jan 1, 1995

By P. F. Kerr

This is not a conventional professional paper. It deals mostly with personal experiences. These concern a background in applied mineralogy. Your committee asked me to do this. I accepted with a California enthusiasm which has since diminished with the approach of a Chicago winter. Nevertheless, I wish to thank your committee and also to apologize in advance for omissions and inadequate statements, as such a paper must possess. My introduction to applied mineralogy took place in 1922 at Stanford University. Physicists had recently demonstrated that crystalline powders would reflect x-rays in a systematic manner. Professor A.F. Rogers sug¬gested that significant x-ray reflections might be obtained from powdered opaque minerals. With the aid of Professor D.L. Webster in the Physics Department, I constructed an x-ray diffraction outfit. It was a crude affair, but it worked. Starting with 1924, we secured recognizable patterns of a goodly number of ore minerals (1,2,3). Today x-ray diffraction outfits are common, and a card system of mineral identification is constantly used.

Jan 1, 1981

By N. M. Komkov

The main operation of obtaining zinc from sulfide raw materials by hydrometallurgical technologies is the oxidation roasting of zinc concentrates in fluidized bed furnaces. The technical-economic parameters are determined by the parameters of the roasting process, which depend on the composition of the initial raw materials, the temperature of the bed and on other factors. The predetermined roasting temperature is maintained due to the change of specific efficiency as well as to the quantity of the heat removed from the bed. The efficiency of caissons depends at a high degree on the composition and the thickness of the accretion formed on the surface of the caissons. Forecasting the roasting results is impossible unless we know the mechanism of the accretion formation. The aim of the present paper is the thermodynamic analyses of the behavior of the charge compositions under roasting and the determination of the potential mechanism of the accretion formation. The thermodynamic analyses show that under conditions of the oxidation roasting the thermodynamic probability of the formation of zinc sulfate is higher than the probability of the oxide formation until a temperature of 873°K is reached. The thermodynamic probability of the formation of the lead sulfate is higher than the probability of oxide formation in the entire temperature range of roasting. The probability of formation of ferrites and silicates of zinc decreases only insignificantly the sulfate stability. The results of the investigation of the accretions composition formed under roasting of concentrates with particle sizes less than 0.02 um (60%), containing 65% of sphalerite (ZnS), 12% of pyrite and chalcopyrite (FeS2 and CuFeSz2 each, 3% of galenite (PbS), 7% of silica and other non-ore minerals, have shown that the composition of accretion varies depending on the depth of the accretion layer. The accretions on the caissons and the thermo-siphons consist mostly of zinc sulfate (more than 50%). The accretions of forchamber consist mostly of zinc oxide. They also contain ferrites and silicates. The formation of the sulfate zinc accretion in the cold parts of the fluidized bed furnace (the caissons and thermo-siphons) may be explained by a lower temperature on the surface and probably by a catalytic influence of the present oxides in the formation of S02 and sulfates. The nature of the structure of the accretion in the hotter parts of the furnace may supposedly be explained by the formation of elemental vaporous zinc during roasting.

Jan 1, 2003

By Yi Tan, Kazuki Morita, Yaqiong Li

Molten Si-Al alloy, with the addition of Sn, was used for metallurgical grade Si purification by a low-temperature solidification method, with the aim of improving the recovery rate of Si. In this ternary melt, bulk Si was grown with a planar front by a directional solidification process under a well-controlled thermal gradient and growth rate conditions, thereby reducing the contamination of solvent metals. Effects of cooling rate, amount of Sn addition, and temperature gradient on the quality of bulk Si were determined. The criterion for constitutional supercooling for single-phase growth from multicomponent melts was employed to evaluate the growth process.

Jan 1, 2015

By U. Lauwers

The influence of different waste materials in sinter blends on the quality and mineralogical composition of a sinter is described. As a result of partial preservation of the original textures of waste materials in the final product the degree of assimilation of the original material in the sinter product can be ascertained. Recycling of waste materials such as dolo char , arc-furnace slag, scrap fmes, mill scale and BOF-mud via the sintering process a saving on costs of raw materials such as flux and fuels, and a reduction on pollution can be achieved. A comparison of a typical sinter with a sinter produced through the utilization of waste materials showed a distinct correlation between certain types of waste material and some metallurgical properties. Dolochar in a sinter blend acts as part of the fuel and flux that are normally added to a sinter mix. Generally dolochar improves the quality of the sinter and decreases the consumption of coke. Other waste materials adversely influence the quality of the sinter. The glass and calcium ferrite content of a sinter when dolochar is used in the blend is similar to that of a sinter produced with only coke as a fuel in the sinter mix. The glass content is lower and the calcium ferrite content is higher, in a sinter produced from dolo char in the blend compared to a sinter produced with additions of other waste materials. Changes in the mineralogical composition are related directly to the metallurgical properties of the sinter product.

Jan 1, 1991

By K. Osseo-Asare

Third phase formation, the separation of a solvent extraction organic phase into two liquids, is generally attributed to the limited solubility of the extracted complexes in the hydrocarbon diluents. Much of the research on third phase fomiation, therefore, emphasizes experiments designed to establish the stoichiometry of the species responsible for the limited solubility. This work offers a different approach, based on the recognition that the solvent extraction third phase, in fact, corresponds to the middle phase in a microemulsion fluid system. Using the tri-n-butylphosphate (TBP)-diluent-water-electrolyte system as a model system, current concepts of microemulsion phase behavior are utilized to develop a general framework for interpreting and predicting the patterns of phase behavior in solvent extraction systems.

Jan 1, 1999

By Agnes Y. Lee

he U.S. Bureau of Mines developed a method to treat lead-contaminated soil and ebonite battery casing wastes to produce a nonhazardous material. The cleanup procedure involves wet screening to separate a minus 18-mesh soil fraction; removal of metal1ic lead, rocks, wood, etc. ; carbonation to change lead sulfate to acid-soluble lead carbonate; size reduction; acid leaching; and rinsing. The casing wastes undergo size reduction and washing to remove the lead sulfate sludge before carbonation. Similarly, the minus 18-mesh soil is carbonated, then acid leached and rinsed. In leaching, fluosilicic acid (H SiF,) and hydrogen peroxide (H20,) are used to dissolve lead compounds. An electrowinning method is employed to strip lead from the lead-rich leachate. The acid content in the leachate is replenished with fresh H,SiF, acid prior to recycling. Treated casing wastes and soils pass the Toxicity Characteristic Leaching Procedure (TCLP) test and can be reclassified as nonhazardous materia1s. Based on this process, a conceptual pilot plant has been designed which will be demonstrated on wastes from two Superfund sites.

Jan 1, 1993

By Milton Manrique

The thermal decomposition of zircon concentrates in a non-transferred arc thermal plasma flow reactor was investigated. The plasma torch was operated using argon-helium and argon-nitrogen mixtures as plasma gases. The effect of power, feed rate and zircon particle size was studied. Products were characterized by XRD, SEM, TEM and chemical analytical techniques. The average size of the product was in the submicron range. Free energy minimization plots were used to predict the behavior of the system under different operating conditions. A kinetic model to describe the different stages of the thermal decomposition process is proposed. The results of this investigation showed a significant segregation process where the zirconia-rich product is collected in the reactor while the silica-rich product is collected in the filter. TEM analysis indicated that silica vapor is condensed on the surface of the zirconia particles.

Jan 1, 1996

By E. J. Peuraniemi

Primary copper production using suspension smelting techniques like Outokumpu Flash Smelting always causes some dust formation. Flue dust particles are formed when sulphide feed material reacts violently with oxygen inducing particle disintegration and total desulphurisation of fragments. In the process, flue dust follows the off-gases to the heat recovery boiler (HRB) where its sulphation takes place because of prevailing conditions. Sulphation releases heat and causes also a drop in particle melting temperature and, further, particle sticking to the walls and heat exchange tube banks. Sulphation of synthetic CU20 particles were examined using a laboratory scale fluid-bed reactor. This study aims to a better understanding of flue dust behaviour in a HRB and, thus, to a better operational practise and design of a HRB. The effect of PSO/PO2 -ratio and temperature on the sulphation kinetics were tested. Standard chemical analysis, light optical and scanning electron microscopy with energy dispersive spectroscopy were used to examine the samples.

Jan 1, 2001

By T. T. Chen

Gold in the Twin Creeks ore is primarily associated with arsenian pyrite. During pressure oxidation, the sulphides are solubilized, but part of the dissolved iron reprecipitates as jarosite and as an iron sulphate-arsenate-phosphate phase. The pressure oxidation products are subjected to cyanide leaching. The cyanide leach residues consist of quartz, gypsum, bassanite, anhydrite, small amounts of jarosite, an iron-sulphate-arsenate-phosphate phase, as well as trace amounts of orthoclase, rutile, pyrite, hematite and monazite; all these particles are dispersed in a fine grained matrix of illite-muscovite. The autoclave leach residues contain a small amount of carbonaceous matter. Many gold grains are detected on the surfaces of the carbon particles, and these gold particles are not leached during cyanidation. The gold particles are typically 0.1-0.2/Lm in size and commonly are embedded in the carbon surface or are coated with a K-AI-Si-S-O phase on the surface of the carbon. The gold grains are consistently associated with elevated CI contents (50-300 ppm Cl). The poor gold cyanide leach recoveries, which initially occurred in the Twin Creek developmental circuit under certain operating conditions, are attributed to the presence of chloride in the feed. This results in the formation of soluble gold chlorocomplexes in the autolcave and the subsequent sequestering of the gold on the surfaces of the carbon particles.

Jan 1, 2000

By Hong Yong Sohn, Miguel Olivas-Martinez

"Different approaches are used for calculating the ‘energy requirement’ of a process. The determination of energy requirement becomes confusing for a process in which a fuel is also a reactant. The key issue is which heat of chemical reaction should be included in the ‘energy requirement’ value. We will use the example of ironmaking processes to illustrate the problem. The different approaches essentially boil down to the question: does one include the combustion heat of the reductant used in the reduction reaction or just the heat of the reduction reaction? Depending on the viewpoint, either approach can be accepted; it is a matter of convention. There is a need, however, to select a standard approach because the absolute value of ‘energy requirement’ of a process depends on the choice. The energy requirement of a novel flash ironmaking process will be compared with that of an average blast furnace operation.IntroductionDifferent approaches are used for performing energy balance calculations and perhaps more significantly in presenting the ‘energy requirement’ of a process. The question becomes more involved for a process in which one or more reactants are also used to generate the process heat by combustion. Often the key issue is which heat of chemical reaction to include in presenting the ‘energy requirement’ of the process.It is worthwhile to note at the outset that the difference in energy requirements between different processes for converting similar raw materials to the same desired product is largely unaffected by the choice of chemical reactions to be included. However, the absolute value presented as the ‘energy requirement’ of a process can be different by a large amount depending on the approach. We use the example of ironmaking processes to illustrate the problem. In these processes, as currently practiced or under development, carbon and/or hydrocarbons (including hydrogen) are used as the fuel as well as the reactant for reducing the iron oxide mineral.The different approaches in this case essentially boil down to the following question: does one include the combustion heat of the reductant used in the reduction reaction or treat the reductant portion as just a reactant? Depending on the viewpoint, either approach can be considered acceptable. It is a matter of convention. There is a need, however, to select a standard approach because the absolute value of ‘energy requirement’ of an ironmaking process (e.g., the currently dominant blast furnace process) depends on such a choice. It is particularly important to clearly state the specific approach used when the energy requirement of ironmaking is compared with those of other industrial processes such as petrochemicals production."

Jan 1, 2014

By Xie Hao

According to its raw materials orthogonal test scheme is designed and a large number of systemic experiments were carried out in order to study the sintering characteristics of three types of fine ores in Kunming Iron&Steel Co.Ltd(KISC). The effects of carbon mixture ratio and basicity on sintering time, agglomeration ratio, physical properties and utilize coefficient were researched via single factor analysis and range analysis. The experimental results show the best mixture ratio of each fine ore. Analysis found that the influence of the carbon mixture ratio is more significant than which of the basicity on the sintering process except agglomeration ratio of foreign ore.

Jan 1, 2009

By R. G. Reddy

The Margules .equation is used for interpreting excess Gibbs energy of several ternary systems. In the present study activity coefficient of &apos;a dilute solute, 2, in a binary solvent 1-3 was derived. The derived expression is used to interpret logarithmic activity coefficient of oxygen and sulfur in several metallic systems. Self interaction parameter of the solute is derived from the partial function of solute using constant compositional path. An expression for logarithmic activity coefficient and self - interaction parameter of solute is also derived using Maclaurin infinite series. The derived equation is based on Maclaurin infinite series used successfully to deduce thermodynamics of self interaction of oxygen as a interstitial atom in two metallic systems. The predicted thermodynamic parameters values using Maclaurin infinite series and Margules. equations, are in excellent agreement with the experimental data and also our predictions are far more accurate than the predictions made by other models.

Jan 1, 1996

By S. R. Reddy, R. G. Reddy

"The Margules equation is used for interpreting excess Gibbs energy of several ternary systems. In the present study activity coefficient of a dilute solute, 2, in a binary solvent 1-3 was derived. The derived expression is used to interpret logarithmic activity coefficient of oxygen and sulfur in several metallic systems. Self interaction parameter of the solute is derived from the partial function of solute using constant compositional path. An expression for logarithmic activity coefficient and self - interaction parameter of solute is also derived using Maclaurin infinite series. The derived equation is based on Maclaurin infinite series used successfully to deduce thermodynamics of self interaction of oxygen as a interstitial atom in two metallic systems. The predicted thermodynamic parameters values using Maclaurin infinite series and Margules equations, are in excellent agreement with the experimental data and also our predictions are far more accurate than the predictions made by other models.1 IntroductionIn most of the pyrometallurgical high temperatures processes, interactions of solutes such as oxygen, nitrogen and sulfur, with the solvent atoms are most important during refining processes. There are numerous theories are developed [1-25] to interpret the thermodynamics of solutes in multicomponent alloy systems. Which are mainly developed using statistical or Quasichemical equations.Wagner [4] developed one energy parameter ideal solvent model based on activity coefficient of solutes compositional dependency. He used one energy interaction term which is not able to account for interaction energy parameters for the same solute concentration at different solvent compositions and also it is ineffective model to predict for strong interacting systems."

Jan 1, 1996

By A. E. M. Warner

Inco Limited has long and extensive experience in converting nickel-copper primary smelting mattes over a broad range of nickel/copper weight ratios and combined nickel-copper-cobalt contents. At the Copper Cliff Smelter, the composition of the converter product matte has to meet the requirements of the matte separation process; at the Thompson Smelter, converter matte of a different composition is cast into anodes for nickel electrorefining; and in Soroako, Indonesia, a very low copper product matte is granulated for the Japanese market. Recently, Inco has conducted pilot plant testing of three possible nickel-copper matte continuous converting routes, namely flash converting, oxygen top blowing-nitrogen bottom stirring, and tuyere blowing. This test work has generated substantial new information on nickel-copper matte converting chemistry. This overview paper reviews the metallurgy of nickel-copper matte converting, in particular the behaviour of cobalt and the operating conditions required to meet the iron and sulfur specifications of the product matte. The relevant thermodynamic information is used to discuss the industrial data.

Jan 1, 2003

By Giuseppe Bonifazi

Minerographic and petrochemical research was carried out on crude ore samples from the complex polymetallic Zn-Cu-Pb sulfide ores of , Sotiel in Huelva province west of Seville, Spain. A computerized image analysis system was used to define the structural and textural characteristics of the ore to obtain information on the degree of liberation of the different minerals (i.e. pyrite, sphalerite, galena, chalcopyrite). Techniques of digital multispectral image processing of reflected light microscopy images were used. Particular structures were identified by means of mineral associations and numerically quantified to obtain useful information for designing beneficiation processes.

Jan 1, 1991

By D. M. Hausen

It has been demonstrated that microscopic techniques can be applied in a practical manner to the study of spodumene liberation in the processing of pegmatitic ores at the Kings Mountain spodumene plant, Kings Mountain, North Carolina. Spodumene and associated non-opaque gangue minerals are identified and quantified by microscopic point-counting of polished thin sections of heads, concentrates, middlings and tails fractions. Specially prepared polished thin sections? provide uniform thickness of particles for measurement of diagnostic optical properties and the alternate use of incident and transmitted light in distinguishing the various gangue and ore minerals. Spodumene is commonly associated and interlocked with quartz, albite, microcline and muscovite. Concentrate grade depends on the degree of spodumene liberation, which in turn depends on the crystal size and textural association of interlocked minerals. The liberation of spodumene can be measured as a function of screen size by means of microscopic point-count data. Microscopic data also provide useful metallurgical information about the nature of diluent minerals in spodumene concentrates, and the form of lithia losses in the tails. Lithium assays correlate closely with microscopic spodumene analyses in various flotation products from Foote Mineral&apos;s Kings Mountain plant, and confirm the applicability of quantitative optical microscopy to the study of liberation and recovery of spodumene from pegmatitic ores. A better understanding of recovery-grade relationships was developed as a result of quantitative microscopy studies.

Jan 1, 1981

By John Hanna

The University of Alabama Mineral Resources Institute (MRI) has developed a unique process for selective fatty acid flotation of carbonate gangue from sedimentary apatites (francolite) in the pH range of 4-6, without collector conditioning of the pulp. The process, which does not require an apatite depressant, was modified to beneficiate a high MgO siliceous phosphate matrix from South Florida. The modified process includes two flotation stages, one for carbonate removal, as mentioned above, and the other for phosphate recovery from the siliceous gangue. The selective flotation separation of the carbonate and phosphate from siliceous constituents of the matrix at various pH levels and collector dosages are discussed. In the carbonate flotation stage, about 70% of the MgO was rejected in the froth, and the phosphate flotation stage produced concentrates analyzing about 31% P20S&apos; 0.7% MgO and 4% acid insolubles. The overall P20S recovery in the two stages is about 85%.

Jan 1, 1989