Search Documents

By G. L. Liu

"Deformation Banding ( DB ) in cold rolled mild steel has been experimentally established by microstructure investigation. Deformation banding model includes such deformation mode when it is applied to rolling texture simulation. The cause for the occurrence of deformation banding is the reduction of the total work for plastic deformation through a relaxation of the deformation constraints. In the first DB model, all grains are assumed to band from the first deformation step. Such an unrealistic assumption has been eliminated in the new model by the introduction of a banding criterion based on an energy minimizing approach. The prediction is closer to the measured texture by applying banding criterion and setting critical resolved shear stresses (CRSS) ratio for { 110 } and { 112 } slip modes to 0.85.IntroductionBased on the continuum theory of plastic flow and deformation mechanism of crystallographic dislocation slip, Taylor's FC ( Full Constrain ) theory [1] has been widely used in texture modeling. As the process of cold rolling of sheet materials produces a microstructure consisting of elongated or equiaxed flat grain or cell, the ""lath"" and ""pancake"" relaxed constraints ( RC ) models [2, 3] were introduced as the successful improvements over the classical FC model. It has been also recognized that crystals may split into different orientations during deformation and the term deformation banding is used to describe such deformation processes [4, 5]. Lee et al. [6, 7] pointed out that the success of the RC theory in predicting textures depends on the physical processes of deformation banding. They developed so called Deformation Banding ( DB ) model by considering DB in the longitudinal plane to be accounted for by the RC method and allowing DB in the rolling plane. DB model was applied to simulate the texture development in bee case [8], the predicted bee rolling textures are in reasonable agreement with the measured textures. In the first DB model, however, all grains are assumed to band right upon the first deformation step. A banding criterion was formulated [7] which states that DB will occur if the work used in DB model is less than that in RC model. Such criterion has been incorporated into the original DB model for texture simulation and is referred to as DBC ( Deformation Banding Criterion ) model."

Jan 1, 1998

By W. L. Dalmijn

Glass recycling in the Netherlands 'has grown fr.om 10.000 to 300.000 tonnes per annum. The various advantages and problems of the glass cycle with reference to the state of the art in the Netherlands is given. Special attention is given to new technologies for the automated sorting of cullet with detection systems. In Western Europe the recycling of glass has, become a success story. Because of this, the percentage of ,glass cullet used in ,glass furnaces has increased. To meet the quality demands of the glass industry, automated sorting for the removal of stones, non-ferrous metals and other impurities ,had to be developed and incorporated in glass recycling plants. ;In Holland, Germany and other countries, the amount of glass collected has reached a level that colour-sorting becomes necessary to avoid market saturation with mixed cullet. Recently, two systems for colour-sorting have been developed and tested for the separation of bottles and culletin the size .range of 20 -50 mm. With the increased capacity of the new glass recycling plants, 120,000 -200,000 tpy, the quality systems have also to be improved and automated. These quality control systems are based on tile automated sorting technology developed earlier. for the glass recycling plants. The data obtained are automatically processed and printed. The sampling system and its relation to the theory of Gy will be described. Results of both developments in glass, recycling plants will be described.

Jan 1, 1995

By Esher Hsu

Keywords: Recycling, Consumer Battery, Fee rates On November 11, 1999, all types of spent consumer batteries are proclaimed to be collected in Taiwan. Under current recycling system, all producers and importers of consumer batteries have to pay a collection/recycling fee to the Recycling Management Fund (RMF) of EPA based upon the rate approved by EPA. Collectors and recycling plants receive subsidies from RMF according to the collected and treated amounts audited by an independent auditing organization. Collected spent consumer batteries only reached 923 tons in 2002 equivalent to 10% of the total quantity sold at the same year. How to increase the collection efficiency of used batteries becomes an important issue for EPA in Taiwan. The objective of this study is to explore current recycling system of spent consumer battery in increasing collection efficiency. Results provide some suggestions to Taiwan EPA regarding recycling route, recycling system, recycling rates, and recycling subsidies.

Jan 1, 2005

By R. J. Wesely

The paper describes the various methods which are currently being used or considered to refine gold and silver. These methods are then compared on a technical and economic basis. Conclusions are drawn on the factors which might influence the choice of process for different feed stocks and economic constraints

Jan 1, 1990

By Xinli Wang, Matthew Andriese, Jiann-Yang Hwang, Zhiwei Peng, Byoung-Gon Kim

"The microwave reflection loss (RL) of ferric oxide is studied in the temperature range from 297 to approximately 1400 Kat frequencies of 915 and 2450 MHz. It is shown that the maximum microwave absorption with RL of -38.46 and -35.97 dB can be obtained for ferric oxide having thicknesses of 0.03 and 0.01 m at 915 and 2450 MHz, respectively. The maximum absorption peak with RL below -10 dB is in a 250 K temperature range from 723 to 973 Kat 915 MHz, which shifts to the range between 823 and 1073 K at 2450 MHz. This migration is in good agreement with the variation of the dielectric loss tangent of ferric oxide.IntroductionMicrowave irradiation has distinguishing characteristics such as volumetric and selective heating compared with conventional methods, leading to extremely broad applications in materials heating and processing [1-5].The efficiency of microwave heating was found to be dependent on various factors, such as microwave power [6], frequency [7,8], radiation time [8], applicator geometry [8], sample microwave absorption properties and position as well as dimension [9-11 ], etc. Among these parameters, sample dimension plays an important role but is usually neglected by researchers in microwave processing of materials. In fact, although numerous studies have been directed toward the utilization of microwave energy to assist materials heating and processing, few reports were released on the effect of sample dimension [12,13].This is because all aforementioned factors influencing microwave heating generally exert interactive effects to each other during the heating process, making clarification of the effect of sample dimension difficult. Therefore, it is necessary to propose a parameter or concept for quantifying the effect of absorber dimension on microwave heating, increasing heating efficiency."

Jan 1, 2013

By D. E. Karvelas

Argonne National Laboratory is conducting research to develop a cost-effective and environmentally acceptable process for the separation of high-value plastics from discarded household appliances. The process under development has separated individual high purity (greater than 99.5%) acrylonitrile-butadiene-styrene (ABS) and high-impact polystyrene (HIPS) from corruningled plastics generated by appliance-shredding and metal-recovery operations. The process consists of size-reduction steps for the commingled plastics, followed by a series of gravity- separation techniques to separate plastic materials of different densities. Individual plastics of similar densities, such as ABS and HIPS, are further separated by using a chemical solution. By controlling the surface tension, the density, and the temperature of the chemical solution, we are able to selectively float/separate plastics that have different surface energies. This separation technique has proven to be highly effective in recovering high-purity plastics materials from discarded household appliances. A conceptual design of a continuous process to recover high-value plastics from discarded appliances is also discussed. In addition to plastics separation research, Argonne National Laboratory is conducting research to develop cost-effective techniques for improving the mechanical properties of plastics recovered from appliances.

Jan 1, 1996

By Z. B. Moukhametshina

The process of various zirconium alloys iodination by the iodine vapor was investigated. The nature of impurities, conditions of iodination, iodine flow rate, and zirconium tetraiodide condensation rate effect on the metal impurities transfer process was analyzed, both qualitative and quantitative correlations were established. Impurities were classified according their transfer extent. Another classification of impurities transport dependence on iodination process temperature was also offered. Obtained results were compared with impurities transport data in the process of iodide refining available in literature. Some impurities transport mechanisins and iodide-refined metals improvement possibility by means of iodination conditions control were discussed.

Jan 1, 1997

By Zhengjie Chen, Wenhui Ma, Jijun Wu, Kuixian Wei

The gasification reactivity of PC (petroleum coke), strengthened by addition of different potassium carbonate proportions using different grinding medium, was investigated by using thermogravimetric analysis (TGA). Results showed that the gasification reactivity of PC not only increased with the increase of catalyst-loaded, but also showed the effective improvement by anhydrous alcohol. The PC was mixed with potassium carbonate [K2CO3] catalyst at 0.5%, 0.8%, 1.0% and 1.5%, and then ground wet with distilled water. The CO2-gasification rate of PC was only 77.35%, 80.55%, 84.07% and 85.88% under the gasification temperature 1100 °C and holding time 120 min, at different K2CO3 respectively. However, when the PC was ground in anhydrous alcohol at the same condition of catalyst-loading, the gasification rate of PC reached 95.43%, 96.63%, 95.50% and 95.61% at the holding time of 108 min, 101 min, 74 min and 35 min, respectively. It was shown by FTIR, SEM and EDX determinations that the anhydrous alcohol used as the grinding medium can further improve the gasification reactivity of PC when compared with the distilled water.

Jan 1, 2016

By Yunyan Wang

Diagrams of pc-pH for the complex ions concentration and pH value and -g- for activity coefficient and ionic strength ln±MnSOI4had been drew based on the thermodynamic principle of coordination chemistry and combined with Pitzer theory at 298.15K. The diagram of -g- indicated that -gincreased sharply from 0.0000 up to 1.2147 when I changed from 0.00 ln±MnSOIln4±MnSO4to 0.09; The increase of -gbecame slowly when I was more than 1.00 and less than 1.69; kept still when I ln±MnSOln4-g±MnSO4was more than 2.25 and less than 4.00. Diagrams of pc-pH illustrated that the minimum solubility of Mn(OH)2(s) increased with the increase of I, the pc increased from 6.5 to 5.5 when I increased from 0.00 to 4.00; The pH of the minimum solubility of Mn(OH)2(s) increased with the increase of I, the pH increased from 11.80 to 12.76 when I increased from 0.00 to 2.89, the pH kept still when I (I was less than 4.0) increased. There is single function relationship between the minimum solubility of Mn(OH)2(s) and relevant pH in different I.

Jan 1, 2010

By Hang Goo Kim

A computer simulation has been carried out to predict the distribution behavior of minor elements such as Pb. Zn, Bi, Sb and As in recently proposed copper smelting and converting processes with submerged oxygen injection in which tonnage oxygen is used with a shielding gas. In this study the technique of stepwise equilibrium modeling was employed and some of the thermodynamic data were updated or reassessed. The volatilization and slagging of undesirable elements were investigated in copper smelting (steady-state) system, copper matte converting (batch) system, and the combined (smelting + converting) system at extremly high oxygen-enrichment levels. The predicted minor-element behavior under high oxygen- enrichment was compared with that in the Noranda process (normally 42% oxygen-enrichment in smelting and 24% in converting) and the reverberatory process using air. The effects of various operating parameters such as temperature, the final matte grade in smelting, the initial matte grade in converting and the O/Fe ratio in slag on the behavior of minor elements are discussed.

Jan 1, 1991

By Yuanbo Zhang

Keywords: Complex Iron Ores, Roasting, Tin, Zinc, Pellets, Comprehensive Recovery. The complex iron ores containing tin, zinc are typical refractory ores. Large reserves of the ores are found in China and have not been utilized efficiently so far. A new process of tin and zinc recovery and pellet preparation from iron concentrate containing tin and zinc by controlled atmosphere roasting is developed in this investigation. The results of 2573 N/P compression strength of product pellets, the 91.49% and 82.22% volatilization of tin and zinc respectively, are achieved for a concentrate containing 0.39% tin and 0.28% zinc. The strength and chemical compositions of the pellets meet the requirement of blast furnace ironmaking. Volatilization mechanism of tin and zinc are investigated. Thermodynamic study shows that the reduction balance curves of SnO2(s) and SnO(g) are proximate in the presence of carbon, and the standard formation free enthalpy of FeO and SnO2 is also approachable. Therefore, it is difficult to realize the complete volatilization of tin in the form of SnO(g) by selective reduction. But SnO2(s) and SnO(g) will form SnCl4(g) or SnCl2(g) in the presence of chlorides and can be easily volatilized from the ores.

Jan 1, 2005

By G. Mark Aylmore

Various processes have been developed using a combination of elevated temperature and chemical treatment processing to recover Li from silicate minerals. To facilitate further process development, a comprehensive understanding of the deportment of Li and associated minerals in ore bodies is essential to allow the industry to predict the response of ore reserves to metallurgical treatment options. This paper describes results from the integrated use of the John de Laeter Centre’s state of the art analytical and mass spectrometry techniques to characterise a selection of Li bearing ore bodies and determine their amenability to potential processing options for the extraction of Li. The mineralogy, mineral associations, and liberation characteristics of ore-bearing and gangue minerals were characterised using a combination of the TIMA and XRPD studies. The Li content and distribution within minerals were defined using LA-ICPMS and field emission scanning electron microscopy techniques (EBSD, ToF-SIMS) and atomic probe microscopy.

By Jerry D. St. Clair

A multidisciplinary team of scientists and engineers at Wont has been working to understand heavy metal contamination of DuPont process waste streams and technologies for abatement of these metals. As part of this effort, an extensive study was made of a specific waste stream of importance in DuPont's environmental commitment. This 200 gpm stream contains 5-5000 ppm of nickel plus a variety of inorganic and organic constituents. The chemical complexity of the waste rendered conventional. alkaline precipitation ineffective, and only through the simultaneous application of analytical characterization, fundamental chemical understanding, and process engineering did effective technical approaches emerge. In this instance, ion exchange, sulfide precipitation, and caustic digestion ultimately proved successful in reducing the nickel to below the 1 ppm target. The results of this study will be presented, along with key learnings about the process of solving heavy metal contamination problems.

Jan 1, 1994

By Ravi S. Bellur-Ramaswamy, Daniel A. Tortorelli, Robert Haber, Nahil A. Sobh

We optimize continuous quench process parameters to produce functionally graded aluminum alloy extrudates. To perform this task, an optimization problem is defined and solved using a standard nonlinear programming algorithm. Ingredients of this algorithm include 1) the process parameters to be optimized, 2) a cost function: the weighted average of the precipitate number density distribution, 3) constraint functions to limit the temperature gradient (and hence distortion and residual stress) and exit temperature, and 4) their sensitivities with respect to the process parameters. The cost and constraint functions are dependent on the temperature and precipitate size which are obtained by balancing energy to determine the temperature distribution and by using a reaction-rate theory to determine the precipitate particle sizes and their distributions. Both the temperature and the precipitate models are solved via the discontinuous Galerkin finite element method. The energy balance incorporates nonlinear boundary conditions and material properties. The temperature field is then used in the reaction rate model which has as many as 105 degrees of- freedom per finite element node. After computing the temperature and precipitate size distributions we must compute their sensitivities. This seemingly intractable computational task is resolved thanks to the discontinuous Galerkin finite element formulation and the direct differentiation sensitivity method. A three-dimension example is provided to demonstrate the algorithm.

Jan 1, 2001

By Brajendra Mishra

Molten Salt electrolytic processes offer unique opportunities to extract and refine metals where gaseous or metallothemlic reduction, hydrometallurgical extraction and aqueous electrolytic methods are thermodynamically constrained. Production of aluminum and magnesium by molten salt electrolysis are well known commercial processes. Several other reactive metals, such as lanthanides and actinides, as well as beryllium and calcium, make use of molten salt processing for extraction and refining. This presentation describes the science of molten salt chemistry and electrochemistry for winning and refining of several metals. In addition, recovery of metals from waste process salts by molten salt reduction as well as oxidation have been discussed. Material issues in design of molten salt reactors have been included. Various applications have been presented through case studies. Experimental data have been included to justify the suitability as well as limitations of these specific processes.

Jan 1, 2003

By Tobias Dubberstein, Hans-Peter Heller

The viscosity of Fe-Cr-Mn-Ni TRIP/TWIP (Transformation Induced Plasticity, Twinning Induced Plasticity) steel with varied nickel content is investigated using a vibrating finger viscometer. The viscosity of the melt is calculated from the change in power input in the field coil by an immersed finger into the liquid steel to maintain a constant peak-to-peak amplitude of the sine wave of oscillator compared to the idle state. Nickel content in steel is varied from 3 wt% to 9 wt%. The dynamic viscosity (η) at 1600 °C for 3 wt% Ni is 3.73±0.14 mPas, for 6 wt% Ni 3.50±0.03 mPas, and for 9 wt% Ni 3.93±0.09 mPas. There is a kink from low to high nickel content in viscosity values of Fe-Cr-Mn-Ni alloys. This phenomenon can be explained by a change in coordination number in the melt, as reported for Fe-Ni binary system in literature. The availability of viscosity data delivers relevant input to model free fall atomization processes of FeCrMnNi alloys.

Jan 1, 2015

By D. B. Dreisinger

The zinc pressure leach process developed by Sherritt Gordon, Ltd. permits the direct leaching of sulphide concentrates according to the overall reaction, ZnS +H,zS04 +402.+ZnS04+H20 +S0 The kinetics of the leach are affected by three rate controlling steps; ( l) oxygen mass transfer from the gas to the leach solution, (2) homogeneous oxidation of ferric ion to ferric ion by dissolved 011.ygen and (3) ferric ion leaching of zinc sulphide in the presence of a sulphur dispersing detergent (lignin sulphonic acid). Fundamental studies have been conducted to identify the factors that influence the kinetics of each individual rate controlling step. Oxygen mass transfer studies have been directed toward optimization of the agitator configuration for solids mixing and gas pumping from the atmosphere above the leach slurry. The rate of ferrous oxidation by molecular oxygen and the rate of zinc sulphide leaching by ferric ion have been studied over a wide range of temperature and solution compositions. The study of zinc sulphide leaching by ferric ion was supplemented by a series of interfacial tension measurements in the liquid sulphur - zinc sulphate solution system. The various kinetic studies have been summarized in terms of the importance of each rate to the performance of the process.

Jan 1, 1990

By John W. Cash

The mineralogy and textures of cyclone dust, sludge, and occasional build-ups in the American Iron and Steel Institute (AISI) direct ironmaking pilot plant at Universal, Pennsylvania have been studied by reflected light, transmitted light, and cathodoluminescence microscopy, and phase compositions have been determined by SEM-EDS. The cyclone dust consists of particles of carbon, metallic iron, sulfur-bearing iron, and wustite. Measurements of particles in the sludge indicates that 69% are less than 2.5 um across, 21 % are 2.5-5 um, and 10% are larger than 5 um. Mineralogically the sludge particles are mainly carbon and metallic iron, with minor wustite and sulfur-bearing iron. Build-ups that sporadically develop in the furnace consist of olivine, hercynite spinel, metallic iron, wustite, pyrrhotite, pseudobrookite, akermanite-ferroakermanite and gehlenite. The microtextures shown by the build-ups indicate that much of that material has precipitated at the build-up loci. This study has been supported by AISI and the U.S. Department of Energy.

Jan 1, 1995

By I. Nikolic

Twin-roll casting is an integrated casting and rolling process that involves the continuous solidification of a melt and the plastic deformation of the solidified metal between two rotating rolls. Computer modeling is a valuable tool to help engineers understand the metallurgical process during twin-roll casting. However, commercially available software can only model either the fluid flow/heat transfer of the melt or the plastic deformation of the solid, but not both. In this study, an object-oriented finite element program was developed to simulate the steady-state fluid flow, solidification and plastic deformation of an A7,31 magnesium alloy in a horizontal twin-roll caster. The melt, the mush zone and the solid were treated as a generalized Newtonian flow in an Eulerian reference frame and different constitutive equations were employed to describe the material behaviours. The effect of operational parameters on the solidification process was discussed based on the simulation results.

Jan 1, 2010

By G. Lindkvist

Roasting of concentrates with high impurity levels is normally done in multiple- hearth furnaces where the concentrates are heated with oilfired burners in order to remove As, Sb and Bi before the final sulfide oxidation. Although it is a countercurrent heat exchange process it uses a lot of oil. In order to develop an energy saving, and from a working environmental point of view a less harmful process than the multiplehearth process, pilot-plant tests have been done in a two-stage fluidized bed for partial roasting. The test materials have been As-rich concentrates with 8-25 % As some 5b and Bi. The Cu-content was 0-28 %. The tests have been successful with <0.3 % As,in the calcine and with an elimination of 5b between 80 and 90 %. In order to achieve the proper conditions for good impurity removal, 1.e. right temperature,residence time and sulphur potential, the tests were performed in a special designed roaster. The roaster consists of two beds with the facilities for recirculation of calcine, preheating of the blast, and possibility to use oxygen enrichment. The construction makes it easy to control the reactions that generate the heat in the bed and reduce the amount of dust that passes through the cyclones. As two roasting steps are used, the possibility to obtain optimal conditions for impurity removal is improved and the calcine can either be smelted to a normal matte, or after being dead-roasted in the second stage, be leached in the normal way for gold extraction. The calcine was smelted with slag. The matte and the slag obtained had low quantities of impurities in the matte and a favourable distribution of impurities to the slag.

Jan 1, 1983