Search Documents

By Kim Fagerlund

A novel apparatus for studying refractory infiltration and dissolution/degradation under a temperature gradient was developed. To supersede conventional isothermal refractory testing, a new temperature gradient technique, based on a crucible equipped with a cooling element, has been developed to provide practical information on the penetration and dissolution of refractory materials under cooled conditions. This technique was adopted and applied to several refractory-slag systems. Commercially available magnesia chrome refractory bricks against a copper-containing calcium ferrite type of slag were tested and compared using both a conventional crucible test and the new temperature gradient method. The experiments were conducted at 1300-1420°C under a controlled atmosphere of nitrogen or air. It was noticed that the type of porosity has a significant effect on infiltration of magnesia chrome refractories. Furthemore, the copper-containing calcium ferrite slag caused a severe slag attack and refractory failure in some cases, due to its fluidity and corrosive nature.

Jan 1, 2002

By Steven Wright

The extent and the rate of reduction of slags produced from the smelting of recycled lead batteries were investigated under laboratory conditions using graphite as reductant. Simultaneous reduction of PbO, Fe2O3, Sb2O3 and As2O3 occurred at temperatures of 1180 and 1200°C, with Sb and As reporting to the metal phase while the PbO content of the slag was above 2 wt%. Fuming of As from the metal occurred at lower concentrations of lead in the slag. Discard slags with low levels of As, Pb and Sb were produced. Arsenic levels were reduced to less than accurately measurable by ICP analysis, and Sb levels in the final slags were in the range of 0.1 to 0.2 wt%. The kinetic data obtained were analysed and compared with other measurements on lead oxide containing slags. The results showing a dependence of the reduction rate on the oxidation state and the basicity are consistent with other studies on well characterised industrial and. synthetic lead slags. These results indicate that when carbonaceous reductants are used, the rate of interfacial reactions play an important role in enabling the production of environmentally acceptable discard slags.

Jan 1, 1994

By Jannie S. J. van Deventer

Geopolymers are novel engineering materials with the potential to play a highly significant role in the transformation of the construction materials and building products industry in the push towards sustainable development. These materials are formed by activation of industrial aluminosilicate waste materials such as coal ash or blast furnace slag with alkaline solutions. Geopolymers derived from coal ash can exhibit superior mechanical properties and chemical stability when compared to ordinary Portland cement (OPC). The use of waste-based geopolymers can also result in significant (up to 90%) reduction in carbon dioxide emissions when used in cement replacement applications. In addition to the formation of conventional pre-cast products, these high performance mineral binders are ideally suited to use in the encapsulation of mine tailings, immobilization of heavy metals and back-filling of mines due to their chemical stability and resistance to acid attack. A key attribute of geopolymer technology is the robustness and versatility of the manufacturing process; it enables products to be tailor-made from a range of raw material sources (waste and/or virgin) with specific properties for a given application at a competitive cost. Despite these key technical and environmental attributes, it is the ability to add significant value to coal ash or and/ or metallurgical slag waste streams which drives the commercial development and uptake of the technology.

Jan 1, 2006

By Bora Derin, Onuralp Yucel, M. Seref Sonmez, Murat Alkan

"Latest stage in the production of boron carbide by metallothermic methods using magnesium was the leaching process. Boron carbide particles obtained by self-propagating high temperature synthesis contained several impurities such as magnesium oxide and magnesium borates after the metallothermic reactions. Removal of such contaminates by hydrometallurgical methods required to produce high purity boron carbide. Leaching by concentrated hydrochloric acid solutions resulted in the production of pure boron carbide together with high magnesium and boron containing solutions. Removal of such ions from the spent liquor was the necessity to have dischargeable solution. In this study, precipitation of magnesium and boron compounds from relevant chloride containing spent liquors and the production of saleable products was aimed. The effects of chemical reagents, pH of the solution on the precipitation efficiency of magnesium and boron compounds were investigated in the study. Chemical analysis and the characterisationof solid phases by using x-ray diffraction analysis were the latest stage.Introduction A variety of advanced ceramics, inter-metallic, organic and inorganic compounds, oxygen free single crystals, and polymers can be synthesized by using different SHS techniques [1, 2, 3]. In the SHS process, after initiation, reaction becomes self-sustaining and propagates in the reactant mixture. A high amount of heat which is generated during the process accelerates the reaction rate and thus it makes the process highly productive and economically feasible for different production scales. After the SHS process obtained powder mixture needs to reacted with acidic solutions to purify the product. In this case B2O3 was reacted together with C and Mg to synthesis fine B4C powder resulted in the production of MgO as well according to the Eq. 1 and then MgO was removed from the mixture by leaching with the concentrated HCl solution as shown in Eq. 2, respectively [4, 5]."

Jan 1, 2008

By Fu-Shen Zhang, Mengjun Chen, Jianxin Zhu

"In the present study, different types of cathode ray tube (CRT) glasses were examined by sequential extraction combined with TCLP to provide possible explanations for how Pb and Ba leach out from the waste CRT glasses and to give possible reasons for why they leach out. Sequential extraction results showed that Pb and Ba in the CRT glasses dominanfly presented as the residual fraction. The exchangeable fractions of Pb and Ba were extremely low, less than 0.01 % of the total content, but they were higher than those required by the regulation limits, 5 and 100 mg/L for Pb and Ba, respectively. TCLP tests of the original CRT glasses and CRT glasses residues after each step of sequential extraction demonstrated that the extremely high leaching toxicity of CRT glasses mainly caused by its exchangeable and carbonate fractions of Pb and Ba.IntroductionIn recent years, the amount of cathode ray tube (CRT) contained monitors or TV sets in the market were sharply reduced, since they were substituted by novel and better electronic and electric equipments such as LCD and PDP, leaving huge amount of end-of-life CRTs. 50-85% of the total weight of this kind of computer monitor or a TV set is glass[1,2], which was classified to three categories according to their chemical compositions: black & white glass (BW), color panel glass (CP) and color funnel glass (CF)[3]. In order to provide shielding from X-rays generated during the picture projection process, lead, barium and strontium oxides were used in the glass. In general, a color CRT contains 1.6-3.2 kg of lead . Therefore, these glasses have attracted wide and tense attention due to the potential risk to the environment and human health."

Jan 1, 2011

By F. Kongoli

A computerized thermophysicochemical database is being developed for various processes involved in nickel smelting and converting. This database includes optimized models for slag, matte, liquid and solid alloys in the multicomponent system(s) as applied to batch and continuous nickel smelting and converting processes. This database can be used to quantify the multicomponent and multiphase slag/matte/alloy/gas equilibria, liquidus and solidus surface, tie-lines, solubility and/or losses of nickel and other components in the slag, distribution coefficients, components activities, heat and mass balance, etc. The database also includes optimized models for the viscosity of the slags associated with any of the above processes. Both databases are coupled and this constitutes a very effective method to quantify the effect of each component on several parameters of the smelting and converting processes and to diffuse the confusion that exists in the literature. Several application examples have been given to demonstrate the usefulness of this database for quantitative prediction of the thermophysicochemical properties of the phases involved in actual or developing processes, even in the areas where experiments are difficult or impossible. The considerable cost reduction that results ftom the use of this database as compared to other methods in the improvement of existing technologies or in the development of new ones is discussed along with continuing new developments of this database.

Jan 1, 2002

By D. M. Jones

In May 1999 the first campaign of the BHP San Manuel flash smelting furnace (FSF) will be concluded after having set world records for both campaign length and tonnage smelted for an Outokumpu copper flash smelting furnace. This paper reviews planned process and equipment modifications including: The installation of a new 36,000 mt concentrate storage facility; replacement of the existing dryer electrostatic precipitator with a baghouse; modification of the FSF dry charge bin and feed system to achieve mass flow and uniform feed to the concentrate burner; modifications to the FSF and its ancillary cooling systems; modifications to the waste heat boiler and offgas handling system to increase gas handling capacity and improve process efficiency;- and improvements to the FSF fugitive gas collection system. A brief review of the planning and execution of the scheduled 45 day shutdown is also given.

Jan 1, 1999

By Min Xiaobo

As for treatment of zinc-containing wastewater, traditional SRB (Sulfate Reducing Bacteria) process was used, however, there exist two defects, like toxicity of heavy metal ions and high effluent COD (Chemical Oxygen Demand) value. In this study, a new technique, called ISIS process (Immobilized SRB sludge beads with Inner cohesive carbon Source), in which SRB sludge is embedded in carrier of PVA (Polyvinyl Alcohol) with carbon source that adsorbed on certain material, is put forward for the first time to overcome the two defects existing in traditional SRB process. Furthermore, it has been shown that compared to traditional SRB process, ISIS process increases average zinc removal rate up 30%, average sulfate reduction rate up20%, and decrease average effluent COD value to meet discharge standards. If activated carbon is selected for carbon source adsorption and fixing material, and PVA for immobilization material, the zinc removal rate can reach above 98% under the conditions of 35 and pH 6. Meanwhile, the mechanism of zinc removal has been determinated according to the results from SEM (Scanning Electronic Microscope) and XRD (X-Ray Diffraction).

Jan 1, 2006

By M. G. King

In 1982, Asarco operated six smelters and refineries producing primary copper, lead, zinc, silver and gold. At that time Asarco was still reliant on its custom smelting and refining roots and mined only 25% of its smelting and refining capacity for copper and 10% of its lead smelting and refining capacity. By 1992, Asarco had been reshaped to become largely an integrated primary metal producer operating four smelters and three refineries. Zinc is no longer refined and the mining capacity has been increased to meet 100% of copper smelting and 50% of lead smelting needs. Only one custom smelter is in operation. This paper describes the metallurgical changes and challenges which have occurred in this restructuring of Asarco's operations while maintaining Asarco's position as one of the largest non-ferrous metals producers in the world.

Jan 1, 1993

By Eiki Ono, Atsushi Yamatodani, Shigeru Sunagawa, Yasushi Takasaki, Atsushi Shibayama, Yasunori Higuchi

"During metallurgical processing of non-ferrous metals, smelting residue (inc. smelter slag, flue gas and so on) is inevitably generated as secondary product.In this research, some experimental feasibilities were investigated to recover/remove Cu and As from the residue. Primarily, the removal of As and volatilized materials from the residue was examined by pyrometallurgical treatment (dry-process). In the second stage after treating the residue with a dry-process, leaching and solvent extraction as hydrometallurgical treatments (wet-process) were also investigated by using H2SO4 solution as a two stage leaching treatment, to dissolve various metals from the leach residue. Then, solvent extraction was examined by using LIX-84I as an extractant to recover and separate Cu from impurities from the final (2nd) leached solution. For the leaching stages, the removal of 90 % As and the leaching rate of 85 % Cu could be achieved by 0.25 mol/l and 1.0 mol/l H2SO4 solution, respectively. On the other hand, the extraction of over 90 % Cu and stripping was carried out by solvent extraction. 1. IntroductionIn metallurgical process for non-ferrous metals, smelting residue (inc. smelter slag, flue gas and so on) is inevitably generated as secondary product, i.e., flue dust, slug and so on. The smelting residue includes some useful metals and undesired toxic materials; Cu, Pb, Ca and As, etc.In Japan there is one undisclosed place stockpiled with 10,000 ton of smelting residue from abandoned smelters about 25 years ago. Therefore it is necessary to reduce the residual amount for space and environmental protection including water treatment by separating and removing toxic materials."

Jan 1, 2008

Iron, chloride and manganese are the three major impurities transferred to copper electrowinning tankhouses via chemical and/or physical entrainment. The control of these impurities via bleeding of tankhouse electrolyte is costly. Recently, Eichrom Industries have developed an improved iron control process and tested this process in a pilot study at the Girilambone Copper Company (GCC). The patented process utilizes a fixed bed ion exchange reactor filled with Eichrom's Diphonix® resin. Iron is loaded on the resin and subsequently eluted by a cuprous sulfate eluant. The control of chloride and manganese has been studied using different chemical techniques. The removal of chloride from electrowinning electrolytes was tested using precipitation of chloride as cuprous chloride. Copper wire cuttings are used to produce cuprous ions. Chloride levels are reduced to around 30 ppm in electrolyte at 40°C. The removal of manganese using a precipitation process practiced in zinc electrowinning purification has been tested for implementation. The process involves reacting manganous ions in solution with permanganate ions. The reaction produces an insoluble manganese dioxide reaction product. The bench scale and pilot plant results from testing of these purification processes are reported.

Jan 1, 1999

By Terry C. Cheng

The Akita Hematite Process is currently the only hydrometallurgical iron removal process producing saleable iron by-products in the zinc industry. In this study, McGill University and Akita Zinc Co. have worked together into elucidating the basic precipitation chemistry of the process from the standpoints of hematite product quality and prevailing precipitation kinetics. This work determined that hematite is produced under the applied conditions (T = 195?200oC,PO2 = 103?414 kPa) directly without prior formation of basic ferric sulphate and transformation of the latter to hematite as thought originally. The rate-limiting step responsible for the long retention time (~180 min) was found to be either the re-dissolution of ferrous sulphate according to the batch reactor studies, or the slow hydrolysis of the remaining ferric sulphate according to the continuous reactor studies. Another interesting contrast between the batch and continuous reactor data was the degree of sulphur contamination (1.5 vs. 3.8%, respectively) and the specific surface area of the product (10 vs. 30 m2/g, respectively). These differences in addition to the co-precipitation of SO4-containing phases such as jarosites, alunite, and anhydrite were attributed to the significantly higher supersaturation level prevailing in the industrial continuous autoclaves that yields highly aggregated sub-micron hematite crystallites contaminated with chemisorbed sulphate ions.

Jan 1, 2003

By Snehanshu Pal

"Concrete understanding of fluid dynamics properties inside basic oxygen furnace (LD converter) and hot-metal surface deformation due to impinging oxygen jet is important for optimization of reaction kinetics and maximization of productivity and refractory lining life. In this study various k-å turbulence models and volume of fluid (VOF) method have been used to model fluid flow and interaction of impinging oxygen jet with hot metal for an industrial scale top blown LD converter.RNG, standard and realizable k-å turbulence models are used to study velocity magnitude, stream function, turbulence intensity profiles. Turbulence kinetic energy, turbulence eddy dissipation, velocity magnitude and probable mixing time have been calculated in three locations inside the converter.The average rate of oxygen jet penetration, location of vortex formation, centre line and superficial velocity of impinging oxygen jet, probability of emulsifícation are studied by VOF method.These simulation studies provide better understanding of phenomena inside LD converterIntroductionComputational fluid dynamics (CFD) modeling in the field of basic oxygen steelmaking can improve substantially the understanding of existing processes where investigation of liquid steel flow measurement is hardly possible due to the rough ambient circumstances. In order to reasonably predict gas stirring operations and emulsifícation, mass, momentum, energy transfer and dynamic interaction among ions, atoms, molecules in the bath, detailed information on flow patterns, fluid velocities, and turbulent properties is essential. Concrete understanding of bath fluid dynamics inside basic oxygen furnace is also important for optimization of reaction kinetics inside the bath and maximization of LD converter lining life."

Jan 1, 2012

By N. R. Green, N. J. Humphreys, D. McBride, T. N. Croft, M. Cross, D. M. Shevchenko

"Centrifugal casting offers a route to high quality products in difficult to cast high temperature low superheat alloys and thin section molds. Under centrifugal forces metal is forced into thin sections and can fill thicknesses of less than a millimeter. However, due to the high liquid metal velocities there is a high risk of surface turbulent flow and air entrainment within the liquid metal. The combination of interacting flow-thermal-solidification phenomena and associated defects is a challenging modeling task which the authors have previously described and validated. Capturing the metal-air interface, on what are inevitably complex three dimensional geometries, results in highly computationally expensive simulations and simulating a single cast can take weeks on a single processor. This contribution reports on modeling a complex centrifugal cast, gas entrainment, bubble transport and solidification, employing meshes of up to a million elements and investigates the scalability of the model on high performance clusters.Introduction The ultimate goal of any casting procedure is to produce a defect-free product. For difficult to cast alloys, such as Titanium, centrifugal casting has a number of advantage over conventional gravity methods [1]. In the casting of thin sections, such as turbine blades, the metal is forced into the thin sections under centrifugal forces. The centrifugal force can overcome the backpressure due to surface tension and the metal can fill mould sections with thicknesses substantially less than a millimeter. However, the materials used in these castings [2] tend to be highly reactive and requires low superheat. High liquid metal velocity gives rise to a high risk of free surface turbulent flow and of associated entrainment through free surface turbulence [3] and trapping of gas present in the flow [1]."

Jan 1, 2012

By Asok Kumar Das

"In steel making ferroalloys occupies a commanding role for production of varied quality of steel. Ferroalloys enable alloying elements such as chromium, silicon, manganese, vanadium etc to be safely and economically introduced into metallurgical processes thus giving certain desirable properties of the alloyed metal. Their importance grew with the progress of the steel metallurgy which implied more diversified alloying elements, in better controlled quantities, in purer steel. The ferroalloy industry became a key supplier to the steel industry. Production of ferroalloys generally involves the use of Electric Arc furnace(EAF) into which raw materials(e.g. various metal ores, quartz, coke, lime etc ) with relatively fluctuating physical compositions are loaded. Due to this, one of the major environmental impacts of producing ferroalloys is the emission of dust and fume from the smelting process. INTRODUCTIONFerro Alloys are essential ingredients used for refining, de-oxidation, desulphurization and alloying addition in the production of different types of steel and hence Ferro Alloy industry forms a back bone of iron and steel in the world. Indian ferro alloy industry is more than 45 years old. It produces most of the bulk ferro alloys and a large number of special ferro alloys. The present installed capacity of the Indian ferro alloy industry is sufficient to meet the requirement of existing level of indigenous steel production of about 46 million tonnes. Revised National Steel Policy – 2008 envisages production of more than 100 million tonnes of steel by the year 2011-12, at proportionate annual growth rate per annum. The focus of the policy is to achieve global competitiveness not only in terms of cost, quality and product-mix but also in terms of global benchmarks of efficiency and productivity. In order to achieve the objectives of National Steel Policy and also to meet the requirement of ferro alloys, the Indian Ferro Alloy Industry has to gear up in terms of enhancement in production capacity, sourcing of raw materials, up gradation of technology, improvement in productivity, automation / mechanization, customer satisfaction etc."

Jan 1, 2008

By Bruce Cavender

Managers are frequently faced with the decision to perform a task or manufacture an object in-house or to hire an outside vendor to perform the function. Outsourcing decisions are usually driven by economics: work is outsourced if it can be completed at a lower cost or in a shorter time than it can in-house. A technique termed incremental analysis can be used to make this decision. Incremental analysis examines the financial impact of outsourcing decisions as a function of the firm's fixed and variable operating costs. To use this tool, individual components of production cost are identified as being either constant or varying with levels of production activity. The assignment of cost type can be made in several ways: though analysis of historical operating data, understanding of individual expense types, and so forth. Changes in fixed and variable costs resulting from each potential course of action are explicitly identified to project the financial outcome of each alternative. The alternative having the greatest positive impact on profit is selected for implementation. By using the fixed- and variable-cost framework, the analysis is conceptually straightforward and substantially simplified. Production managers can therefore use incremental analysis as a tool for fast economically beneficial decisions on a real-time basis.

Jan 1, 1999

By M. Wu, A. Kharicha, J. Bohacek, A. Ludwig

"During the horizontal spin casting of rolls, vibrations and mould deformations seems to have a significant effect on the final quality of the product. Sources for vibrations can be found in the poor roundness and a static imbalance of the chill itself. The bending of the mould axis is also considered. Both, vibrations and axis bending, are used as an input for CFD simulations of the flow dynamics of the liquid metal inside the rotating cylinder. The aim is to study the feedback of the free surface behavior in terms of wave propagation and various wave shapes. Introduction The horizontal spin casting process (HSC) is a casting process that has several advantages over the traditional gravity casting processes. Centrifugally cast products have a high degree of metallurgical purity and homogeneous microstructure. A significant gain is observed for the rupture strength, the rupture strain, and the Young modulus. These properties naturally depend on the centrifugal force and thus, the best mechanical properties can be found at the largest distance from axis of rotation. However proper selection of the angular frequency has to be done in order to prevent the so-called ""metal rain"" i.e. metal droplets can fall down from the upper part of the cylinder due to a too weak centrifugal acceleration. In the same time excessive speeds can lead to the appearance of longitudinal cracks caused by the hoop stress in the initially solidified layer. From empirical knowledge other parameters have important influence on the casting products, it includes the pouring temperature, the pouring rate, the mould coating etc. Recently the presence of natural or forced vibrations have been identified as possible additional factors to be taken into account [1-2]."

Jan 1, 2012

By Sergei A. Degterov

A thermodynamic database for the slag, matte and liquid copper phases in the Cu-Ca-Fe-Pb-Zn-Si-O-S system has been developed for the ranges of compositions of importance to the production of copper. When used with the Gibbs energy minimization software and other databases of the F*A*C*T thermodynamic computing system, this database will permit the calculation of matte-slag-copper-gas phase equilibria that take place during copper smelting and converting. The calculations reproduce within experimental error limits all available experimental data on phase diagrams, activities of components, enthalpies of mixing, matte - alloy miscibility gap and tie-lines. The calculated solubilities of Cu in both S-free slag and slag equilibrated with matte are also in good agreement with experiment under all studied conditions, such as at SiO2 saturation, in equilibrium with Fe, Cu or Cu-Au alloys, at fixed oxygen or SO2 partial pressures and at different contents of Pb, Zn and CaO in the slag. Sulfide contents (sulfide capacities) of the slags are predicted within experimental error limits. The distribution of Pb and Zn among matte, slag, copper and gas has been calculated. The calculations are in good agreement with experimental data and predict the distributions under conditions which are difficult to study experimentally, such as at magnetite saturation or under various oxygen partial pressures and iron to silica ratios in the slag.

Jan 1, 1999

By V. Bojarevics, K. Pericleous

"A number of different methods have been developed for noncontact electromagnetic treatment of liquid metal and to investigate the melting/solidification processes. Applying AC magnetic field in terrestrial conditions, along with the buoyancy and thermo-capillary forces, results in turbulent flow. The use of a homogenous DC magnetic field allows damping both of the turbulence and the large scale flow at different rates leading to surprising results at some stages. The dynamic interaction of the turbulent flow with the oscillating interface needs to be accounted if it is required to levitate liquid metal of up to few kilograms without the contact to container walls. At the high values of magnetic field some oscillation modes are damped quickly, while others are modified with a considerable shift of the oscillating droplet frequencies and the damping constants from the non-magnetic case. Numerical models are used to investigate behavior of liquid metal suspended in high DC magnetic fields providing microgravity-like conditions with laminar viscosity and heat transfer to the surroundings.IntroductionSince the early Electro Magnetic (EM) levitation experiments [1] in AC magnetic field it became apparent that the levitated liquid metal is prone to oscillation and instability. The EM and electrostatic levitation experiments with liquid metal droplets show difficulties related to confinement stability and a need for complex correction functions to establish a correlation between the measurements and the droplet material properties [2,3]. Intense internal fluid flow is visually observed, apparently being in the turbulent regime for earthbound conditions."

Jan 1, 2012

By P. Chris Pistorius

Calcium treatment of alumina inclusions, to convert the alumina to molten or partially molten calcium aluminates, is a well-established treatment for steel, to improve the castability of aluminium-killed steel. However, the role of magnesium in calcium-treated steel is not fully clear, nor is the origin of the several percent of magnesium oxide that is often present in calcium-treated inclusions. To study this, steel was sampled after calcium treatment at an industrial steel plant, and the inclusions identified by energy-dispersive X-ray microanalysis (EDX) on polished sections of the samples (analysing the samples in a scanning electron microscope). The predicted fraction liquid in the inclusion was estimated from the ternary alumina-magnesia-lime phase diagram. Inclusions with higher CaO contents generally had lower MgO contents, indicating that the calcium wire is not the origin of the magnesium in the inclusions; this was also confirmed by wet chemical analysis of the calcium wire. Instead, it appears that magnesium-alumina spinel inclusions form during extended ladle contact after aluminium killing and before calcium treatment. While such spinels have been stated to cause poor castability (clogging the submerged-entry nozzle), it is clear that calcium treatment successfully modifies the spinel inclusions to mixed alumina-lime-magnesia inclusions, where the magnesia content contributes substantially to liquefaction of the inclusions: for typical MgO contents of around 10%, the range of Ca:O ratios which yield liquid (or partially liquid) inclusions is extended substantially to lower Ca:O ratios.

Jan 1, 2006