Search Documents

By R. M. Westcott

A two-electrode, direct current, slag resistance furnace (SRF) has been constructed and operated to selectively reduce the zinc and lead contents of non-ferrous slags. The experimental SRF is equipped with multiple methods of gas/solids injection for both mixing and reaction. A computer is used to position the electrodes and for data acquisition. A geometric factor correlation was previously developed at Columbia University for calculating the electrical resistance on the basis of furnace geometry and slag conductivity. The experimental SRF was used to test this correlation.

Jan 1, 1994

By M. Nilmani, J. Sofra

The transverse distributions of the solids discharge velocity and mass flux at the discharge end of vertical and inclined lances were measured in order to detennine the transverse distributions of the axial momentum flux, which is a dominant factor influencing the penetration behaviour of particles into melts during submerged injection. The effects of gas velocity (10 - 30 m/s), solids loading (5 - 10), lance length (0.15 - 1.0 m), lance inclination (vertical downward - horizontal) and particle density (2500 - 8900 kg/m3 ) were investigated, while the lance diameter and particle size were fixed at 10 mm and 220 µm respectively. The particle velocities and mass fluxes were measured by image analysis of particles illuminated in a laser-generated light sheet aligned vertically through the axis of the lance at the discharge point. The particle discharge velocity profiles for vertical downward flows were synunetrical about the centre-line of the lance, with the maximum velocities occurring at the centre-line. The velocities increased with increasing gas velocity, increasing lance length and decreasing particle density in accordance with previous observations. The transverse mass flux profiles were also synunetrical for vertical downward flows, however at the lower gas velocities the peaks in the profiles were displaced from the centre-line of the lance by a fractional diameter of about 0.15. The particle discharge velocity profiles become increasingly asynunetric as the lance orientation was changed from vertical to horizontal, with higher particle velocities present near the top wall of the lance. The mass flux profile also became asyrrunetric as the horizontal orientation was approached, however in this case, the profile became biased towards the bottom of the lance. The effect was much more pronounced for a gas velocity of 10 m/s than for 30 m/s, showing the relatively stronger gravitational influence as the velocity was reduced.

Jan 1, 1996

By H. M. Friede

An experimental study of iron-smelting techniques used in the South African Iron Age by H. M. FRIEDE, Ph.D. and R. H. STEEL (Visitors) The main factors involved in the primitive smelting of iron (ore, charcoal, temperature, air supply, process control) were evaluated in an experimental furnace that was constructed to the pattern of an Iron Age furnace found at Melville Koppies Nature Reserve, Johannesburg. In particular, the characteristics, action, and efficiency of skin bellows were investigated to gaina better understanding of the air-supply system used. Sixteen specimens of iron ore, slag, and metallic iron (excavated material and material produced in the experimental furnace) were submitted to analysis. The results of the analyses are reported and discussed.

Jan 6, 1977

By Guanghua Ai, Xiong Huang, Huashan Yan, Ting Li, Tingsheng Qiu

"Cyanide tailings of gold and silver concentrates contain considerable quantities of copper-lead-zinc sulfide minerals that can be recovered. However, the strong inhibition effect of cyanide often makes it difficult to recover these sulfide minerals effectively. In this research, a sample of cyanide tailings was investigated based on the principles of process mineralogy; activating flotation tests were carried out for the target minerals in the tailings, and the activation mechanism of the activator and its influence on the target minerals were investigated by Fourier transform infrared spectroscopy (FTIR). Mixed flotation of copper and zinc was carried out using QJ-01, a combined agent containing sulfite, as the activator of copper and zinc minerals, and ammonium dibutyl dithiophosphate (ADD) and butyl xanthate (BX) as the combined collector. Copper concentrate was obtained from the mixed concentrate by using a combined inhibitor of sodium sulfide and zinc sulfate to inhibit the zinc mineral. Zinc concentrate was extracted from the copper tailings by using copper sulfate as the activator and BX as the collector. The flotation test yielded copper concentrate with a grade of 22.56% and recovery of 76.96%, and zinc concentrate with a grade of 42.56% and recovery of 82.29%, which shows that comprehensive recovery of the sulfide minerals – copper and zinc –from the cyanide tailings was realized. The FTIR analysis showed that CN- was chemisorbed on the surface of chalcopyrite and sphalerite following cyanide treatment, while the combined activator QJ-01 containing sulfite reduced CN- into SCN- and weakened the complexing ability of CN- with metal ions on the mineral surface, thus achieving a good activation effect on chalcopyrite and sphalerite. The results of this study can provide practical guidance in increasing the resource utilization ratio of cyanide tailings in gold mines, and thus contribute to alleviating environmental problems caused by stockpiling cyanide tailings. INTRODUCTION Cyanidation, the most widely used technology for extraction of gold, has several advantages such as high recovery, process maturity, low cost, etc. According to available data, the annual discharge of cyanide tailings from China's gold mines exceeds 20 million tons (Li et al., 2011). Lower grades of exploitable gold ore entail increased discharge of cyanide tailings. Huge quantities of cyanide tailings are regarded as waste and stored, resulting in significant wastage of land resources. Moreover, residual beneficiation reagents, cyanide ions, and heavy metal ions in cyanide tailings cause severe pollution of water and land (Laitos et al., 2013; Donato et al., 2007; Mudder and Botz, 2004). In addition, cyanide tailings often contain valuable elements such as gold, silver, copper, lead, zinc, sulfur, and iron, which, if not recycled, would result in considerable wastage of resources. Hence, it is imperative to study the reduction and safety of cyanide tailings, and the mineral resources present in them."

Jan 1, 2018

By C. Zhou, B. Whisner, J. Carr

Proximity Detection Systems (PDSs) are used in the mining industry for protecting mine workers from striking, pinning, and crushing injuries when they work in close proximity to heavy machines such as continuous mining machines (CMMs). Currently all Mine Safety and Health Administration (MSHA) approved PDSs are magnetic field based systems which can be influenced by the presence of wire mesh that is commonly used for supporting roof and ribs in underground coal m ines. In this paper, researchers at the National Institute for Occupational Safety and Health (NIOSH) characterize the influence of the mesh on the performance of magnetic PDSs by measuring the magnetic field difference around a CMM caused by the presence of the mesh. The results show that the magnetic fields are generally enhanced by the mesh which causes the PDS detection zones to be increased correspondingly. It was discovered that the fields around the joints of two mesh sections have the greatest enhancement and thus deserve more attention. In addition, it is found that the presence of mesh can also cause a variation in the generator current. The influence of mesh is characterized by the change in the generator current with respect to the distance between the generator and the mesh. It was found that the generator current change caused by the mesh can be significant (on the order of ten) when the mesh is extremely close to the generator (e.g, less than 1 cm) and is negligible when mesh is relatively far (greater than 0.15 m). The findings in this paper can be used to develop guidelines and best practices to mitigate the influence of mesh on PDSs. INTRODUCTION The Mine Safety and Health Administration (MSHA) requires operators of underground coal mines to equip place-changing continuous mining machines (CMMs) with proximity detection systems (PDSs) to protect mine workers from striking, pinning and crushing injuries when they work around these heavy machines. Although a variety of technologies can be implemented for proximity detection, the magnetic-field-based PDS that was originally developed at the National Institute for Occupational Safety and Health (NIOSH) has shown great effectiveness in challenging mining environments and currently all MSHA-approved PDSs are magnetic-field-based systems. As shown in Figure 1, a magnetic PDS typically includes two major components----the magnetic field generator and the Miner Wearable Component (MWC). Magnetic fields are generated by injecting a high electric current into a ferrite-rod antenna sealed in the generator. The magnetic field strength detected by an MWC varies with the distance between the MWC and the generator. In a typical PDS, multiple generators are mounted on different locations of the machine. The relative location/zone of an MWC is determined based on the field strengths from different generators picked by the MWC. Ideally, for a PDS to work properly in the underground, the magnetic fields generated by the different generators should be stable and not vary with the environment, as the system would interpret any variation of the magnetic field as a result of the distance change between the machine and the miner wearing the MWC. In reality, however, this is not always the case since magnetic fields can be altered by a number of environmental factors such as the presence of steel wire mesh that has been widely used in underground coal mines for supporting roof and ribs In this paper, the influence of mesh on the PDS performance is investigated and the magnetic field change caused by the mesh is measured.

Jan 1, 2019

This paper presents the findings from an experimental study of the effects of shock and gas penetration breakage mechanisms in rick blasting. A blasthole liner method, which realistically seperated these two basic sources of energy in blasting, was developed and utilized. The use of four different explosives with contrasting detonation behaviour produced a wide variation in the nature of explosive energy transfer to the rock. Through extensive field experiments it was found that, relative to low VOD dynamite, the high VOD emulsion imparted greater shock to the rock and therefore produced finer fragmentation and greater back damage. The comparatively lower heave energy of the emulsion caused less immediate blast results were obtained with watergel and ANFO explosives, which have detonation behaviour and energy partitioning charecteristics lying between emulsions and dynamite.

Jan 1, 1990

By M. Boher, J. Lehmann, M. C. Kaerlé

"In the production of high quality steel, the understanding of the interactions between liquid steel and refractories and of their effect on steel purity and cleanness are becoming more and more important.An experimental study has been per-formed in order to estimate the importance of the reaction between a MgO-based tundish refractory and an Al-killed steel. The results show a pollution of the liquid steel:•the silicon content of the liquid steel increases due to the reduction of the silica of the refractory by the aluminum contained in the steel; and•a reoxidation of the steel occurs and the formation of an oxide layer on the refracto-ry, mainly composed of spinel crystals and of Ca-aluminates is observed.The transfer mechanisms of the various elements are analyzed."

Jan 1, 1997

By Gaifeng Xue, Lei Zhang, Aimin Duan, J. Y. Hwang, Lina Wang

"The removal of chemical oxygen demand (COD) from coking wastewater was experimentally investigated using a three-dimensional electrode reactor. The experimental results showed that the refractory organics in coking wastewater can be effectively removed by this process, and COD removal efficiency was affected by the operating parameters, such as electrolytic retention time, particle electrode dosage, initial pH, current density, aeration amount and electrical conductivity. The experimental results show that the three-dimensional electrode could have a COD removal efficiency of more than 60% and a running cost of no more than 6 YUAN (RMB)/t. This indicates the great potential of a three-dimensional electrode reactor in engineering applications as an advanced treatment methods for coking wastewater.IntroductionCoking wastewater is generated from coal coking, coal gas purification, and by-product recovery processes of coking; it is composed of phenolic compounds, heterocyclic compounds, polycyclic aromatic hydrocarbons, ammonia, cyanide, polycyclic nitrogen-containing aromatics, acyclic compounds, etc. Most of these constituents are refractory, poorly biodegradabile, toxic and carcinogenic [1-3]. Currently, coking wastewater is usually treated by different forms of A/O biological nitrogen removal processes as the primary treatment means, but the aforementioned processes are not efficient enough to meet the requirements of the National Discharge Standard in China (GB13456-1992). According to the continuous requirement on improving environmental protection for the coking industry (revised 2008), increasing wastewater utilization ratios and reducing the discharge of effluent in the coke industry have to be implemented for cleaner production and sustainable development. Therefore, advanced technologies need to be developed to treat coking wastewater and reutilize the product as industrial cooling water, which would be one of the best choices to achieve zero discharge of wastewater and reduce water consumption per ton of steel produced. In this study, a three-dimensional fluidized bed electrode reactor was adopted for the advanced treatment of coking wastewater, and the effects of operating conditions, including particle dosage, initial pH, current density, supporting electrolyte, as well as aeration amount on the COD removal rate, were investigated. Its running costs were also estimated."

Jan 1, 2012

By Shailendra Chawla, Ashok Jaiswal, Sonu

Side spalling/skin failure occurs due to the high-induced stress in underground structures. In such cases, rock bolting or other support systems are being used to control the skin failure or spalling of the pillar. The nature of these support systems is passive, which acts during the deformation. These support systems restrict the displacement considerably of the side/or roof surface of the excavation. Ultimately, it improves the stability of the structure because of the increment in residual strength of rock mass. It is noted that these passive support systems give very low confinement in the range of 0–0.015 MPa at the onset of failure. As the level of confinement will be very low and dependent with progress of failure, triaxial test was not found practically suitable. Thus, an alternative procedure of testing has been proposed. In the procedure, sides of sample have been restricted little bit by using adhesive tape. It provides the limited boundness on the lateral direction (LBLD) of rock specimen. The uniaxial compression strength (UCS) test has been performed on 30 numbers of cylindrical rock specimens using the servo-controlled stiff testing machine. Specifically, two rock types (medium-coarse–grained and coarse-grained rocks) were studied in terms of stress–strain behaviour so that a full residual strength envelope for each specimen was obtained. This study reveals that the residual strength of limited confined rock specimens has been significantly increased as compared to unconfined rock for both groups of rock types. The average residual strength of LBLD specimens of fine-grained rock and medium coarse-grained rock has been increased around 12 times, and five times as compared to unconfined rock, respectively. The average peak strength of LBLD rock specimens has been increased in the range of 30.5 to 48.6% for coarse-grained rock. The results of this study have been presented in terms of peak strength, residual strength and Young’s modulus of rock, and the post-peak failure behaviour of rock specimens was also critically analysed through a stress–strain curve.

Mar 21, 2024

By Youjun Tao

Falcon centrifugal gravity separation tests were conducted to study desulfurization and de-ashing performance with different size fractions of a high-sulfur Chinese -0.5mm fine coal in a dense medium. Performance indicators such as combustible recovery, ash and sulfur rejection, and desulfurization efficiency were used to evaluate the separation efficiency. The results show that for -0.5 mm coal particles, all performance indicators except ash rejection are higher for the Falcon concentrator than for flotation. More specifically, for the +0.125 mm size fraction, Falcon centrifugal separation produced better ash and sulfur rejection performance than froth flotation. However, the Falcon concentrator also showed higher combustible recovery but lower ash and sulfur rejection than froth flotation for the -0.125 mm size fraction.

Aug 1, 2013

By K. H. Luo, J. Y. Liu

An experimental study on interparticle breakage of three iron ores was carried out by compressive stressing of particle-bed in a piston-die device. The feeds to the particle-bed stressing were five narrow size fractions in the size range of 0.2~3.2 mm respectively and a wide size fraction of 0/4.0 mm. The pressures applied were in the range between 30 and 360 MPa. The results show that the energy absorption of the particle bed increases linearly with the pressure; the increase of the product fineness with the pressure declines as the pressure goes up; and the product size distributions resulting from interparticle breakage of different narrow size fractions have no self-similarity. Using data obtained from the piston-die compressive stressing test, the suitability of a previously-developed material-characterization model for interparticle breakage was verified for these ores. It is shown that the particle-bed compression test conducted with piston-die device in lab-scale may provide a cost-effective way of studying and modelling size-reduction of ore materials by interparticle breakage.

Jan 1, 2014

By T. Ito, N. Tokashiki, H. A. Bilgin, Ö. Aydan, T. Akagi

This study is concerned with the electric potential induced by deformation, fracturing and sliding of non-piezoelectric geomaterials. In experiments, the acoustic emissions together with electric potential measurements were also measured in order to see how the so-called seismic electric signals are associated with new fracture occurrence and propagation and sliding in case of existing discontinuities. The outcomes of this experimental study may explain why such electric potential variations may occur during the fracturing and sliding of non-piezoelectric geomaterials. On the basis of these outcomes, their possible implications in geo-engineering and geo-science are discussed. Ce travail concerne 1e potentiel électrique produit par la déformation, 1a fracture ou le glissement du matériel géologique non-piézoélectrique. Aux expérimentations, on a mesuré 1es émissions acoustiques avec le potentiel électrique afin de constater la relation entre les phénomènes de glissement ou de formation et de propagation de nouvelles fractures le long des discontinuités existantes. Les résultats de ce travail expérimental expliquent pourquoi de telles variations de potentiel electrique se produisent durant le glissement ou la fracture du matériel non-piézoélectrique. Sur la base de ces résultats, on a discuté de leurs éventuelles implications dans les domaines de 1a géologie et de 1a géo-ingénierie. Diese Studie befasst sich mit dem elektrischen Potential das durch die Deformation, Bruchbildung und Gleiten von nicht-piezoelektrischen Geomaterialien induziert wird. In Experimenten wurden die akustischen Emissionen zusammen mit elektrischen Potentialmessungen gemessen, um zu sehen, wie die so genannten seismischen elektrischen Signale mit neuer Bruchbildung und Ausbreitung sowie Gleiten im Falle von vorhandenen Diskontinuitäten verbunden sind. Die Ergebnisse dieser experimentellen Untersuchungen könnten erklären warum elektrische Potential Schwankungen während der Bruchbildung und dem Gleiten von nicht-piezoelektrischen Geomaterialien entstehen. Auf der Basis dieser Ergebnisse, wurden ihre möglichen Implikationen in Geoingenieurwissenschaften behandelt.

Jan 1, 2003

By M. Tsunekawa, T. Takamori, T. Hirajima

In spherical agglomeration in water, the pattern of the growth behaviour of agglomerates is essentially determined by the surface chemical properties of the particles and the oil-water interface. When particles are suitably hydrophobic and oil-water interfacial tension is not too low under an adequate condition for agglomeration, large agglomerates are formed in the initial stage and micro- agglomerates do not appear. When particles are poorly wetted by oil and the interfacial tension is low, initially micro-agglomerates are formed and, after certain aging time, they grow to large agglomerates in a relatively short time without formation of intermediate size agglomerates. Under adequate conditions, the amount of oil and power input do not produce any remarkable effect on the pattern of growth.

Jan 1, 1980

By Y. Ooishi, Y. Matsumoto, T. Arai, H. Ohta

The multi-circular face shield (MFS) is a new type of tunnelling machine for construction of the special cross section and has been put to practical use in 1988. The MF shield has two circular faces partially overlapped in a single shield machine and can construct the cross section shaped like glasses for the double track railway. And it is possible to equip two or more cicular faces horizontally or vertically, if necessary. During the development of the MF shield the experiments have been carried out for the purpose of estimating the excavatability and the face stability of the MF shield. As a result it was confirmed that the both types of MF shield (one with double faces aligned horizontally and the other with double faces aligned vertically) has higher performance in the face stability and lower value in the cutter torque and the total thrust than the conventional circular shield.

Jan 1, 1991

By M. Dayne Aldridge

A description is given of an experimental ventilation control system designed, built, and tested by WVU under United States Bureau of Mines sponsorship. A description is given of the control, system used and the mine-wide microcomputer-based ventilation monitoring system used with it. Test results of experiments conducted with this system at Eastern Associated Coal Corporation's Federal No. 2 underground coal mine are presented. In addition, a brief description is given of a new microprocessor based system presently being tested.

Jan 1, 1980

By Durao F

A multi-layer feed-forward neural network was trained (using the error back-propagation algorithm) to learn a subset of rules designed to stabilise the performances of the copper flotation section of a complex sulphide processing plant and then tested in order to evaluate its expert performances. Two types of neural networks were compared: the classical ones, fully connected between one layer and the adjacents (with different architectures), and entropy networks, partially connected and generated according to a methodology that simplifies its building up. The advantages and drawbacks of both were analysed and compared with classic (rule based) expert systems.

Jan 1, 1995

By A. V. Z. Brink

Rock engineering risk is defined in this paper as a function of the potential ground motion; the vulnerability of the workplace; exposure of people; and a general term – quality of information. The paper describes the development of prototype software that is a combination between an expert system approach for determining overall risk assessment, a risk control recommendation and a basic GIS (Graphic Information System) approach for graphically overlying input parameters and the output risk. The expert system uses a Bayesian probabilistic approach to combine various workplace-related information, a quantified seismological environment and the exposure of underground staff to provide an overall RE risk rating. The risk assessment is dynamic in that it is recalculated each time that any of the input parameters change, for example each time a seismic event is recorded in the area of interest. The code was tested on a data set from Savuka Gold. As risk assessment is not an absolute prediction of a specific outcome, it is therefore not possible to relate to individual case studies and the reliability of this method would only be determined after an extensive period of use with appropiate back-analysis. Le risque dans le génie minier est défini dans cette étude comme une fonction du mouvement potentiel de terrain ; la vulnérabilité du lieu de travail ; l’exposition des personnes ; et un terme général – la qualité de l’information. L’étude présente décrit le développement d’un logiciel prototype qui est une combinaison entre une démarche de système expert pour déterminer une évaluation générale du risque, une recommandation pour le contrôle du risque, et une démarche de SIG (Système d’Information Géographique) pour superposer graphiquement les paramètres d’entrée et le risque de sortie. Le système expert utilise une méthode de probabilité bayésienne pour combiner des informations variées sur le lieu de travail, des données quantifiées sur l’environnement sismique, et l’exposition du personnel travaillant sous terre, pour finalement produire un classement général de risque minier (RE). L’évaluation du risque est dynamique en ce sens qu’elle est recalculée à chaque fois qu’un des paramètres d’entrée change, par exemple à chaque fois qu’un évènement sismique est enregistré dans la région. Le code fut testé sur un ensemble de données obtenues de Savuka Gold. Comme l’évaluation du risque ne constitue pas une prédiction absolue d’un résultat spécifique, elle est par conséquent difficile à rattacher à des cas individuels et la validité de cette méthode ne pourrait être déterminée qu’après une longue période d’utilisation avec analyse rétrospective appropriée. Das Gesteinstechnikrisiko wird in dieser Arbeit als Funktion einer möglichen Bodenbewegung definiert; die Anfaälligkeit des Arbeitsplatzes; das Ausgesetztsein der Belegschaft; und ein genreller Begriff - Qualität der Informationen. Das Papier beschreibt die Entwicklung einer Prototyp-Software, die eine Kombination zwischen einem Expertensystemzugang für die Bestimmung der gesamten Risikobeurteilung ist, eine Empfehlung zur Risikokontrolle und eines fundamentalen GIS (graphisches Informationssystem) Zuganges für graphisch darüberliegende Eingangsparameter und das Outputrisiko. Das Expertensystem verwendet eine bayesische Wahrscheinlichkeitsannäherung, um verschiedene mit dem Arbeitsplatz in Verbindung stehende Informationen, ein quantitativ bestimmtes seismologisches Umfeld und das Ausgesetztsein des Untertag-Personals zu kombinieren, um eine gesamte RE-Risikobewertung zur Verfügung zu stellen. Die Risikobeurteilung ist insoferne dynamisch,daß sie stets nachkalkuliert wird wenn sich irgendeiner der Eingangsparameter ändert, z.B. jedesmal wenn ein seismischer Fall im Interessensbereich aufgezeichnet wird. Der Code wurde auf einem Datenbestand von Savuka Gold geprüft. Da die Risikobeurteilung nicht eine absolute Vorhersage eines spezifischen Resultates ist, es ist folglich nicht möglich, sich auf einzelne Fallstudien zu beziehen und die Zuverlässigkeit dieser Methode könnte nur nach einer umfangreichen Benutzungsdauer mit geeigneter Postanalyse bestimmt werden.

Jan 1, 2003

By John D. Carriere, Jean Leung, Daniel. Laguitton, Michael .. J. Burrows

"The objective of this expert system application in a copper-zinc concentrator, is to increase the availability of assay data through substitution for erroneous data. The assay data is used by the Operations personnel and automatic process control strategies to control flotation circuit performance. Two online X-ray fluorescence analysis systems analyze 24 streams across four divisions to provide the required data. Data availability of individual streams average 90% while the resulting circuit availabilities are 70%. The unavailability of correct data results from mechanical, X-ray or process problems. The erroneous data can be identified by process experts using knowledge relating stream interdependencies and historical process behaviour. An expert system was devised to provide real time identification of erroneous data and substitute for that data with the ultimate aim of improving metallurgical response by both the operator and automatic control systems.The paper discusses the early development work and architecture of the knowledge base designed using Neuron Data's expert shell NEXPERT.INTRODUCTIONThis paper describes the early development of an expert system (ES) prototype at the Kidd Creek concentrator. The project is a joint undertaking of the Kidd Creek Division of Falconbridge Limited and CANMET. Kidd Creek entered into the project to apply heuristic rules to the XRF assay data to improve the metallurgical control of the flotation process by increasing availability of analysis data. This project provided a problem of suitable size and future expandability while making use of a wide base of in-house expertise and experience. Another important benefit is the introduction of expert system technology to the site providing tools and experience for future system selection and technology application. CANMET has an on-going interest in assessing various aspects of ES technology (hardware, software, knowledge engineering, integration) while addressing problems in process operations that could most readily benefit from the technique. CANMET's role in the project was to provide project assistance, financial support, substitution algorithm assistance and software for data substitution. The knowledge bases (rules) have now been completed and are to be tested in the online environment."

Jan 1, 1989

By Huaiyu Liu, Shan Liu, Dashang Chang, Maixi Lu, Yaqun He, Yali Kuang

The expert system for coal preparation plant design mainly solves the crux--separation flowsheet design and optimization of product structure. There are twelve basic flowsheets available in the system which are representative of financial plants. The system can select better flowsheets automatically according to the property of feed and scale of plant. Then, it can choose the best flowsheet and product model from the better flowsheets through analysis and optimum calculation. The expert system is made up in Turbo Pascal 6.0 and consists of three sub-systems: Lump and grain coal system, coal slimes processing system, and raw coal system. Several representation methods, such as production rule, procedure, and object-oriented programming, are used to express the expert's knowledge in the system. To decide the optimum product structure, Zangwill's method is used to make an advance product model. The expert system has the performance of interpretation strategy, by 'tracer" technology and pre-arrangement text, and of learning new expert's knowledge.

Jan 1, 1996

By C. Kirmanli

The purpose of this paper is to develop an expert system for hydraulic excavator and truck selection in surface mining. Hydraulic excavators and trucks are finding increasing applications in mining operations. Hydraulic excavators are extensively used especially when bringing electricity to rural areas is difficult and for small-scale mining. This paper describes an expert system, which selects the optimum hydraulic excavator truck configuration such that unit production cost is minimized and technical constraints such as geological, geotechnical and mining constraints are satisfied. The system has four modules: user interface, rules and an methods, databases and output module. The expert system in this study is developed within KappaPC shell. It supports object-orientated technology for the MS Windows environment. The software provides a very useful tool to practitioners, saving time and cost. Equipment selection is a recurring and expensive problem of mine planning and often involves interdisciplinary experts from different fields. It is very difficult and expensive to bring together all these experts. The capabilities of the expert system developed are illustrated in the paper. The software overcomes the difficulties of selecting the proper equipment for surface mining operations, which is very important, and results in substantial savings. Equipment databases for hydraulic excavators with 15-59 yd3 capacities and trucks with 35-360 tons are constructed and these databases are used to select the proper configuration. A case study is carried out for Soma Surface Coal mines in Turkey. Keywords: surface mining, expert systems, equipment selection, hydraulic excavators, diggability

Jan 1, 2009