Search Documents

By C. E. M. Meskers

End-of-life Electronic and Electrical Equipment, o_cially called WEEE, is unjustly regarded as mainly a waste management problem. What is structurally overlooked is the enormous resource impact of these devices. EEE rep- resents a tremendous metal resource, which should be uti- lized through e_ective recycling, which has a much lower environmental footprint than primary production. The actual amount of end-of-life EEE recycled today is embar- rassingly low since insu_cient EEE is collected and part of the collected EEE is exported to developing countries, where it is largely not entering o_cial recycling systems. To achieve a global recycling society issues like technol- ogy, economics, life cycle structure, stakeholder aware- ness and legislation have to be addressed in a global, co-operative manner so that sustainable closed product cycles can be obtained. Requirements for a "global re- cycling society" are de_ned to address today's reality of global ows of used consumer products, taking into ac- count the likely needs of the future.

Jan 1, 2009

By T. B. Counselman

AFTER several years study, the Universal Atlas Cement Co. decided to rebuild its plant at Leeds, Alabama. The entire old plant, which was to operate during the new construction, was then to be scrapped with the exception of two kilns. The quarry was to be mechanized, new and larger kilns installed, with the most modern type of equipment all through the plant. Raw grinding operations at all of the Universal Atlas plants were dry. However, the dust hazard of this operation and the growing emphasis on occupational diseases made wet grinding attractive. Coal at Leeds is cheap, so that a slightly higher coal practice was unimportant. Power was cheap, so that waste-heat boilers were not desirable. Since new kilns were to be installed, these could be made long enough to make filters unnecessary. Wet raw grinding could be either the old practice of open-circuit compartment mills or closed-circuit grinding in accordance with metal-lurgical practice. The latter saved power and steel wear and saved initial investment. This had been demonstrated in cement plants. Also, the elimination of tramp oversize was a most important advantage. Ease of chemical control was another factor. Blending in the thickener, with elimination of slurry mixers had been found practicable. Therefore, if wet raw grinding were used at all, the advantages were clearly in favor of closed-circuit grinding. Detailed layouts of the most modern possible closed-circuit dry-grinding plant and of a closed-circuit wet-grinding plant were prepared, and careful estimates were made of initial invest-ment and operating costs. Full consideration of all the factors involved resulted in a decision to install wet closed-circuit grinding.

Jan 1, 1939

By T. B. Counselman

AFTER several years study, the Universal Atlas Cement Co. decided to rebuild its plant at Leeds, Alabama. The entire old plant, which was to operate during the new construction, was then to be scrapped with the exception of two kilns. The quarry was to be mechanized, new and larger kilns installed, with the most modern type of equipment all through the plant. Raw grinding operations at all of the Universal Atlas plants were dry. However, the dust hazard of this operation and the growing emphasis on occupational diseases made wet grinding attractive. Coal at Leeds is cheap, so that a slightly higher coal practice was unimportant. Power was cheap, so that waste-heat boilers were not desirable. Since new kilns were to be installed, these could be made long enough to make filters unnecessary. Wet raw grinding could be either the old practice of open-circuit compartment mills or closed-circuit grinding in accordance with metallurgical practice. The latter saved power and steel wear and saved initial investment. This had been demonstrated in cement plants. Also, the elimination of tramp oversize was a most important advantage. Ease of chemical control was another factor. Blending in the thickener, with elimination of slurry mixers had been found practicable. Therefore, if wet raw grinding were used at all, the advantages were clearly in favor of closed-circuit grinding. Detailed layouts of the most modern possible closed-circuit dry-grinding plant and of a closed-circuit wet-grinding plant were prepared, and careful estimates were made of initial investment and operating costs. Full consideration of all the factors involved resulted in a decision to install wet closed-circuit grinding. The capacity of the new kilns was established at 4000 bbl. per day. Two new kilns were installed, each with a capacity of 80 bbl. per hour. Since 625 lb. of raw material is required to make a barrel of finished cement, the capacity of the grinding plant for the new kilns had to average only 1250 tons per day. Sufficient additional grinding capacity had to be provided for the two remaining old kilns, or their possible replacement by a third new kiln. The grinding rate, therefore, was set at 90 tons per

Jan 1, 1939

By T. B. Counselman

AFTER several years study, the Universal Atlas Cement Co. decided to rebuild its plant at Leeds, Alabama. The entire old plant, which was to operate during the new construction, was then to be scrapped with the exception of two kilns. The quarry was to be mechanized, new and larger kilns installed, with the most modern type of equipment all through the plant. Raw grinding operations at all of the Universal Atlas plants were dry. However, the dust hazard of this operation and the growing emphasis on occupational diseases made wet grinding attractive. Coal at Leeds is cheap, so that a slightly higher coal practice was unimportant. Power was cheap, so that waste-heat boilers were not desirable. Since new kilns were to be installed, these could be made long enough to make filters unnecessary. Wet raw grinding could be either the old practice of open-circuit compartment mills or closed-circuit grinding in accordance with metal-lurgical practice. The latter saved power and steel wear and saved initial investment. This had been demonstrated in cement plants. Also, the elimination of tramp oversize was a most important advantage. Ease of chemical control was another factor. Blending in the thickener, with elimination of slurry mixers had been found practicable. Therefore, if wet raw grinding were used at all, the advantages were clearly in favor of closed-circuit grinding. Detailed layouts of the most modern possible closed-circuit dry-grinding plant and of a closed-circuit wet-grinding plant were prepared, and careful estimates were made of initial invest-ment and operating costs. Full consideration of all the factors involved resulted in a decision to install wet closed-circuit grinding.

Jan 1, 1939

By Terry A. Kirk

"This paper describes Derrick High Frequency Vibrating Screens and their process performance in grinding circuit applications. The benefits of screen sizing in closed circuit grinding are illustrated by case histories from a wide spectrum of mineral industries.INTRODUCTIONHigh capacity, reliable wet screening equipment is increasingly in demand by the mining and allied industries for separations finer than 1/.7 5mm (I/ mesh). The continuing search for improved energy efficiency and reduced steel consumption in comminution has Jed to greater scrutiny of every aspect of circuit design and operation, including the classifier efficiency (selectivity) function.Derrick Manufacturing Corporation has been developing high frequency screening machines designed specifically for grinding circuit applications since 1973. Successful installations are currently operating in iron ore, copper, coal, uranium, phosphate and other extractive industries."

Jan 1, 1984

By B. Friedrich, A. Weyhe, H. Heegn

"Nickel-metal hydride batteries (Ni-MH) are storers of electrochemical energy, which have a higher specific storage capacity than lead or nickel-cadmium batteries. The demand for Nickel-metal hydride batteries is increasing rapidly since their market launch in the early 1990’s. Today there is no suitable and sustainable recycling process to recover nickel, cobalt and rare-earth metals. The discarded batteries are used today in the steel industry as alloy material because they contain nickel. Cobalt and rare-earth metals (RE) are lost; they are non-recycleable.In a German governmental funded research project, IME Aachen, ACCUREC Mühlheim and UVR-FIA Freiberg are cooperating in processing as well as in creating a feasibility study. The target of this project is the development of a new recycling process for metal recovery from Ni-MH-batteries. The proposed process described in this paper consists of a combination of mechanical, pyrometallurgical and hydrometallurgical processing steps. This process is capable of treating all types of Ni-MH-batteries. After comminution steel and organics are separated. The separated Ni-MH is smelted in an electric arc furnace. The products are a nickel-cobalt alloy and a slag phase enriched with rare-earth oxides for further treatment to ‘mischmetal’. Both the Nickel-Cobalt alloy and the ‘mischmetal’ will be directly used in battery production."

Jan 1, 2003

By H. Wagner

It is a great privilege for me to have been asked to present the closing address to this most successful symposium on backfill in the South African mining industry. When I accepted this invitation I did not fully appreciate the tremendous progress made on most aspects of backfilling in the last few years. The number and quality of papers presented at this symposium bear testimony to the mining industry's determination and success in introducing backfill in underground mines to improve strata control and environmental conditions, and to provide better protection to mineworkers against the hazards of rockbursts and rockfalls. Many contributions demonstrated that these benefits can be achieved at a reasonable cost, and in some instances improved grade and higher rate of face advance result in improved economics. In my closing address I will attempt to summarize the progress made in the various aspects of backfilling underground workings and to identify those areas which, in my opinion, require further attention and effort. I will undertake this review under the following main headings: ? fundamentals of backfilling; ? design of backfill systems; ? operation of backfill systems; ? control of backfill systems; and other aspects of backfill systems.

Jan 1, 1988

Thank you for the invitation to this forum today. I have a hectic schedule in the Mabo legislation process but it is important not to lose sight of the bigger picture and to attend today to talk to you about the Government's role in the development of our country.More importantly, I hope over the next couple of hours to get some feedback on developments in this area from people very much involved on a day to day basis.

Jan 1, 1993

By P. Mengé

The covering of a hydraulically filled goethite pond is discussed from a geotechnical point of view. The characteristics of the goethite were defined in order to allow a detailed study of the procedure for the construction of the cover on top of the soft material and a verification of the stability of the cover and side slopes after construction. These characteristics and the main results of the studies are given, as well as the experiences and observations made during the execution of the work. Finally, the monitoring plan, during and after construction, is also discussed and some results are given. The 'Design and Construct' contract form was used to allow the contractor to choose the optimum and most economical method to realize the closing of the pond, based on his experience with similar projects. The works were carried out between mid 2003 and the end of 2004. The paper will, amongst others, discuss the special method of working that had to be developed to allow the covering of the whole pond in a relatively short time period, without soil improvement methods such as vertical drains or stabilization by in situ treatment. Fill material was used to establish a platform on top of the soft material so that the cover liner and finishing layer could be installed on top of the fill layer. The 'floating roof' principle was used; subsidences were allowed to occur during the installation of the impermeable top liner and soil cover.

Jan 1, 2006

Jan 1, 1947

By Andrew Cecala

During a recent National Institute for Occupational Safety and Health field evaluation of a newly designed filtration and pressurization system for an enclosed cab of a surface drill, it was determined that the drill operator's respirable-dust exposure was significantly increased during time periods when the cab door was opened to manually guide another section of drill steel into place to achieve additional cutting depth. Although no dust cloud was visible when the door was opened to perform this task, the drill operator's exposure was documented (over a three-day test period) to be nine times higher than when the cab door was closed. Even at this higher respirable-dust concentration, the drill operator's exposure remained well below the permissible exposure limit governed by the federal dust standard; however, an alternative method is being investigated to guide the drill steel in place in order to eliminate this increased exposure. .

Jan 1, 2008

By Joseph L. Petrillo

In July 1997, Kvaerner Environmental signed a unique contract with Echo Bay Alaska called the Transfer Risk and Accelerate Closure (TRAC). The contract called for Kvaerner to assume the responsibilities and obligations associated with closeout of the Alaska-Juneau (A-J) Mine. Kvaerner is an international engineering and construction company with global interdisciplinary experience in the mining industry and environmental remediation. Echo Bay’s requirements called for Kvaerner to: •Provide a fixed price for closure with no change orders. •Negotiate, prepare and implement a final closeout plan as outlined by Echo Bay. •Complete a closure program that exceeded current regulatory requirements. •Improve, expand and maintain a proactive public and community relations program. •Hire Echo Bay employees where possible. •Provide adequate performance guarantees and judicial relief of environmental claims.

Jan 1, 1999

By Adrian Dance

The Antamina orebody is a geologically complex, polymetallic skarn located in the Peruvian Andes. A range of copper and copper-zinc ores are campaigned separately through the concentrator producing copper and zinc concentrates as well as lead and molybdenum by-products. Ore type classification at Antamina is based on chemical assays; geological or lithological variations are not considered. Consequently, each ore type demonstrates a wide range of concentrator performance. Antamina is currently implementing a system to track ore movements from the shovel face to the concentrator. Relatively sophisticated models of the ROM and coarse ore stockpiles ahead of the mill will be used to account for the variable delay between mining and milling. One of the numerous benefits of ore tracking is the ability to directly associate the measured concentrator performance with a physical location in the orebody. Using existing mine planning software, three-dimensional models can be created of such performance measures as metal recovery, concentrate quality, operating cost and reagent consumption. Such a database of information allows the true value of different ore sources to be determined. The value of an ore source is conventionally measured as metal content (individual or combined ?equivalent?) with a cut-off grade applied to indicate some base level operating cost. However, the true value of an ore source should include dynamic factors like haulage cost, reagent use, smelter penalties and even prevailing metal prices. If an ore source is considered from all perspectives rather than simply its potential to deliver value, the concept of ?ore? becomes more flexible. Any ore source that reveals itself to be unprofitable can be eliminated from the mine plan or possibly blended with others to improve its value. The ability to predict mill performance ? and thereby profitability ? is a powerful tool. In an operation such as Antamina, where managing ore sources, campaigns and the delivery of a variety of concentrates in a narrow timeline to customers is a daily challenge, prediction is the key to success and improved efficiency.

May 1, 2003

"The Antamina orebody is a geologically complex, polymetallic skarn located in the Peruvian Andes. A range of copper and copperzinc ores are campaigned separately through the concentrator producing copper and zinc concentrates as well as lead and molybdenum by-products.Ore type classification at Antamina is based on chemical assays; geological or lithological variations are not considered. Consequently, each ore type demonstrates a wide range of concentrator performance.Antamina is currently implementing a system to track ore movements from the shovel face to the concentrator. Relatively sophisticated models of run-of-mine and coarse ore stockpiles ahead of the mill will be used to account for the variable delay between mining and milling.One of the numerous benefits of ore tracking is the ability to directly associate the measured concentrator performance with a physical location in the orebody. Using existing mine planning software, three-dimensional models can be created of such performance measures as metal recovery, concentrate quality, operating cost, and reagent consumption.Such a database of information allows the true value of different ore sources to be determined. The value of an ore source is conventionally measured as metal content (individual or combined ‘equivalent’) with a cut-off grade applied to indicate some base level operating cost. However, the true value of an ore source should include dynamic factors like haulage cost, reagent use, smelter penalties, and even prevailing metal prices. If an ore source is considered from all perspectives rather than simply its potential to deliver value, the concept of ore becomes more flexible. Any ore source that reveals itself to be unprofitable can be eliminated from the mine plan or possibly blended with others to improve its value. The ability to predict mill performance, and thereby profitability, is a powerful tool.In an operation such as Antamina, where managing ore sources, campaigns, and the delivery of a variety of concentrates in a narrow timeline to customers is a daily challenge, prediction is the key to success and improved efficiency."

Jan 1, 2005

Mine rehabilitation is a sustainability issue that has been revisited ad infinitum; however, the persistent lack of demonstrated on-the-ground performance and an increasingly intractable rehabilitation liability in Queensland continue to erode the credibility of the mining industry and regulatory bodies. For at least ten years the need to change the current, process-based approach to rehabilitation to an outcomes-based approach has been apparent. The ISO 14001 series temporarily diverted attention from this important point, however it would appear the limitations of an ISO 14001 approach are now more widely accepted. It is proposed that a successful outcomes-based approach cannot be achieved without meaningful community engagement. The apparently intractable nature of the rehabilitation issue will continue to generate conflict and criticism unless all stakeholders are encouraged to participate in the process of developing robust and practical outcomes for rehabilitation. Sharing the responsibility will ensure the best possible outcome. It is important to recognise the valuable resources inherent in community groups, many of whose committed volunteers have considerable expertise in relevant areas. Community groups should not be seen as adversaries but as allies in the process of solving problems that affect the wider community. Several projects that can be seen as test cases for the engagement of stakeholders exist, and in this paper the process of achieving multiple stakeholder engagement in the context of Environmentally Sustainable Development is discussed.

Jan 1, 2002

By H. Araneda

Throughout Chile?s history, mining has consistently been a leading industry in the country. The 1990s marked the beginning of a boom in Chile?s mining industry, especially in copper mining, due to both foreign and local direct investment in the sector. Mining?s contribution to the GDP was 15.6% at current prices in 2009, and it accounts for 56% of the country?s exports. Chile?s copper market share reached 35% in 2009. The investment portfolio in mining in Chile for the coming decade has been estimated at 90 billion US dollars. The acute scarcity of human resources currently experienced by the mining sector in Chile will be accentuated in the coming decade as a result of this scenario of investments. The situation is, additionally, similar to the one confronted by other countries involved in the mining industry such as Australia, South Africa, Canada, and in Latin America includes, Peru, Colombia and Brazil. A study carried out by Fundacion Chile, ¨Labor Force in the Chile Mining Industry, Diagnostic and Recommendations, 2011-2020? shows the projected labor shortage for the operation of projects in the development stage, considering only the requirements of the process of extraction, processing, and maintenance. The demand, accumulated incrementally, will be around 115,000 technically skilled workers, professionals, and qualified workers. This figure refers to the operational work force, and does not include the human resources that will be required for the prior stage of the engineering and construction of the projects (brownfield and greenfield). The demand for technically skilled workers and professions for the stages of engineering and construction of the projects that have already received investments is estimated to be 190,000 people for the period 2012-2020. The peak of the demand for engineering is 2012, with a figure that surpasses the 12,000 professionals for all of the engineering specialties. The analysis of the formation of human resources at the tertiary level (where tertiary includes technical/vocational and academic degrees at the undergraduate level) for mining and related majors demonstrates that the programs are scarce with a bias toward theoretical contents and that they are excessively long (40% longer than comparable programs in Australia, Canada, and in OECD countries). The completion rates are low, especially in the technical-vocational programs, which have a completion rate of only around 30%. Finally, the rates of attraction of technically skilled labor and professionals towards careers in mining are insufficient to reduce the identified skill gaps. In the case of university professionals such as geologists, mining engineers and engineers in metallurgy, 80-90% will work in mining. In the case of graduates of relevant majors, that cover skills also utilized by other industries, not only mining?such as maintenance workers, operators of fixed and mobile equipment, etc.?the mining sector appears to be unattractive for reasons such as shift schedules, geographical location of work sites, and other factors. On the basis of the available diagnosis a strategy for the sector has been developed (Workforce Development and Skills Strategy) whose objective is (i) to define a Mining Qualifications Framework to identify the critical roles to be filled (ii) to start, with public resources, a ¨fast-track? training program to assure the availability of at least 28,000 operators (machinery operators, truck drivers, etc.) and maintenance specialists in 2015 (iii) to promote the development of training hubs for mining with learning technologies to train technical labor and professionals on the basis of world class standards (iv) to design and implement a campaign oriented toward the perception of mining as an attractive field of employment opportunity (v) to develop curricular innovations for tertiary education programs, on the basis of international benchmarks. Keynotes: Chile, mining, copper mining, skilled human resources

Sep 1, 2012

By S. C. Essack

"Tenova Pyromet has designed a slag flow control valve that throttles the flow of slag in order to control the tapping rate. In addition, the valve has proved to be a reliable tool for closing the furnace during normal operation as well as emergency conditions. The valve makes use of a water-cooled copper element that is hydraulically operated and attached directly to the slag tap-hole. The equipment is compact, simple to maintain, and cost-effective to purchase and install. It can be retrofitted to most existing slag tapholes with minimal modifications.During the development phase, finite element method (FEM) and computational fluid dynamics (CFD) software was extensively used to model predicted operating conditions and to optimize the design. By using CFD, it was possible to understand the flow patterns inside the copper and to optimize these to improve overall performance.The slag valve was installed and commissioned in 2011/2012 on a 12 MW furnace as part of a new mineral wool plant in the USA. It has performed well since its installation despite operating under conditions in excess of the original design criteria. During the first 6 months of operation it quickly became the preferred method of closing the furnace, although the design intent was for occasional use during emergency shutdown conditions only. Since replacing the mudgun as the main method of closing the tap-hole, a few minor changes have been made to the installation in order to cope with the increased heat load and much higher frequency of use."

Jan 1, 2014

By T. Braun, J. Parker

On June 25, 1999, BHP Billiton (BHPB) announced the suspension of operations at the BHP Copper Inc.(BHP) San Manuel copper mine in Pinal County, Arizona. Subsequent to this announcement, BHPB aggressively pursued a number of alternatives for the underground mine and open pit facilities, including continued curtailed operations, sale to a qualified mining operator and closure of the property. After consideration of these various alternatives over a 2.5-year period, BHPB announced final closure of the mine site on January 15, 2002.This paper describes how the BHPB charter and HSEC policy apply during the closure process.

Jan 1, 2004

By Alan Dahlstrand

The Jamestown Mine is a 6.3-kt/d (7000-stpd) open-pit gold mining operation located in the central portion of California's historic Mother Lode district. Most early production from the Jamestown area occurred in underground operations from 1906 through 1916. Pit production began at Jamestown in early 1987 and continued until July 1994. Although additional mineral resources existed, they were deemed to be uneconomic. About 23.3 t (750,000 oz) of gold were produced from pit operations, compared to 31 t (100,000 oz) from early underground mining. Recent operations at Jamestown included two open pits, a flotation mill and a flotation tailings facility. Flotation concentrates were produced in Jamestown and shipped to Yerington, NV for cyanide leaching in a carbon-in-pulp (CIP) circuit.

Jan 1, 1995

By H Jones

Closure cost estimates may be generated at any stage of a mining operationÆs life; commencing with the initial prefeasibility studies and continuing through to the final decommissioning cost estimates. However, not all mine closure cost estimates are necessarily the same. Cost estimates will vary depending on the purpose for which they are prepared, the organisations requiring or undertaking the estimate and the stage of the mining operation. Different organisations can legitimately arrive at disparate cost estimates for closing the same mine because the organisations have different reasons for requiring the estimates. Another, equally valid, reason for potentially wide variations in cost estimates by different organisations on the same mine site is the different definitions of æclosure costsÆ used by different estimators. This paper considers the different approaches by different organisations including operating companies, government authorities and financial organisations and uses a hypothetical example based on practical experience to illustrate some of these differences in estimation methods.The paper suggest that a more consistent approach to closure cost estimating in the Australian mining industry would assist mining companies, governments, the accounting industry and the broader community to better understand this complex component of mine planning. One possible approach to closure cost estimating is briefly outlined.CITATION:Jones, H, 2012. Closure cost estimation - All things to all men?, in Proceedings International Mine Management 2012, pp 115-124 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012