Search Documents

By Thomas Gregor, Brian Garrod

As the popularity of precast concrete segmental linings for tunnels is growing in North America, some problems related to grouting of, and near, these linings are starting to appear. The installation of a segmental lining behind a TBM requires that the annular space around the lining be quickly filled with grout to prevent collapse of the ground. In practice, the filling of the annulus is frequently delayed and takes place a distance behind the machine typically via grout ports centrally located in the segments. If partial collapse of the annulus has occurred, it may become necessary to use higher grouting pressures in an attempt to distribute the grout. There have been several occasions where these increased pressures have caused damage to the tunnel linings. Similarly, compaction grouting adjacent to a tunnel lining can cause damage. This paper quantifies the effects of such grouting on a typical precast lining.

Jan 1, 2005

By S. Stephen Uslan

The purpose of the study was to demonstrate the effect of positive reinforcement, specifically, social reinforcement (SR), on the frequency of eye, hand, and back injuries at four experimental salt mines. Injury data was collected from January, 1976, for the prePOMOST period and from the onset of training to September, 1978, for the post-POMOST period. All data was collected on a month-by-month basis. For the training period approximately 100 managers and supervisors from five plants were trained in the use of positive reinforcement for occurrences of "safe behavior." Each supervisor was also provided manuals and other supportive materials. Additionally, following training, all supervisors were provided some coaching experience to keep the knowledge and capabilities gained during training from being extinguished. The analysis showed significant injury reductions in two sites and no injury reductions in the other two. When the injury data was corrected for the additional man hours expended in the postPOMOST period, a third site showed reduction in injuries. Similar findings were shown when the experimental sites were compared to other sites in the industry. The results were interpreted to support the hypothesis that the application of social reinforcement is related to a reduction in injuries.

Jan 1, 1978

By Bob King

Jan 1, 2005

This paper examines the integration of risk management into the design philosophy of a project to produce a æzero baseÆ design, which targets a minimum capital cost without adversely impacting upon the operating costs of the resulting plant. The concept of zero base design is similar to zero base budgeting and the desired outcome is to improve the economy of the design. Design requirements are questioned in an attempt to distinguish preference, prejudice and myth from necessity. Where doubt remains a risk management approach is adopted. The key to risk management is not risk elimination, but risk mitigation. Risks can be managed by designing them out, but often this involves considerable capital cost penalties and it is more attractive to accept the risk and design an operating strategy to deal with it. The paper discusses this with some examples of real world risk mitigation strategies that resulted in substantial capital cost savings. The paper concludes that as much as a quarter of project capital costs can be eliminated by a combination of zero base design and carefully crafted risk mitigation strategies.

Jan 1, 2004

Despite the claims of energy efficiency and the considerable development that has gone into dramatically extending rolls? life and facilitating rolls? change-out, in the six years since the last SAG conference, only a few HPGR operations have entered the realm of mineral processing. Risk barriers to the take-up of new equipment or processes are: a massive increase in materials handling issues as well as in the number of pieces of equipment required, low total circuit potential energy savings, and similar or higher capital costs. An alternative route is to make use of the complementary strengths of the HPGR and SAG in hybrid circuits. Minimising materials handling issues, providing an ideal balanced feed to the AG or SAG mill, and improving controllability through shifting grinding load as the RoM feed changes, are all potential major advantages to this approach. Conceptual circuit layouts, based on real measured ore and equipment data, are presented here to illustrate the potential production upside, the reduction in operating costs and the reduction in the physical and energy footprints.

Jan 1, 2012

By C. M. Rule, A. K. Anyimadu, L. Knopjes

Ongoing development work on ultra-fine grinding for various applications at the Group?s concentrators has been conducted by Anglo Platinum over the last few years. Current potential applications for mainstream grinding and concentrate grinding are the subject of a group-wide research and development programme. The first 10 000-litre 2.6 MW IsaMill was jointly developed by Anglo Platinum, Xstrata Technology and Netszch for installation at the Western Limb Tailings Re-treatment project in Rustenburg, South Africa. The unit was commissioned in late 2003/early 2004, and has operated in an intermediate concentrate regrind application successfully since. This paper describes the operational performance to date, as compared with the original duty specifications and objectives. The first mainstream M10 000 IsaMill with a 3 MW drive will be operational in November2006 at the Potgietersrus Platinum (PPL) ?Platreef? Sandsloot Concentrator in South Africa?s Limpopo Province. Key Words: Western Limb Tailings Re-treatment Plant, IsaMilling, Platreef, Platinum, Palladium, PGMs, tailings.

Jan 1, 2006

By McHenry Mosier

SUMMARY MERCURY is one of the strategic metals of which the supply has been raised from critical uncertainty to more than enough for essential demands. Work by the Bureau of Mines has contributed substantially to increased production of mercury in the United States and to consequent accumulation of Government stocks. Other contributing factors have been higher prices for mercury and Government loans to operators. The Bureau has undertaken 13 exploration projects, 10 of which have been completed. This work has comprised 28,376 ft. of several types of drilling and 23,798 lin. ft. of surface trenching, and has indicated commercial ore containing 34,800 flasks of mercury and marginal ore containing 26,200 flasks, a total of 61,000 flasks; equivalent, respectively, to domestic production for 8 months, 6 months, and 14 months. As Government stocks are now adequate, domestic production (currently at the rate of 50,000 flasks per year) is gradually being curtailed through Government control of labor and operating supplies.

Jan 1, 1944

By Chengliang Jliang, B. K. Parek, Xuxin Shao

Of the impurities present in phosphate ore, dolomite is the most difficult to remove due to the similar chemical compositions of the impurities and also adsorption of dissolved species of dolomite onto phosphate. A new amphoteric surfactant was found to be a suitable collector for separation of dolomite from phosphate. Flotation results showed that the new amphoteric collector had a high flotation selectivity for dolomite in wide pH ranges. The flotation study of francolite and dolomite in each other's supernatant demonstrated that the dissolved ions had little effect on the selectivity of the new collector, but were detrimental to the flotation separation using sodium oleate as collector. A phosphate concentrate with 35.2% P2O5 with 90% recovery was obtained using 290 g/t of the amphoteric collector from a mixture of francolite and dolomite containing 26.2% P2O5. The rejection of MgO was 81.41%.

Jan 1, 1999

By Roozbeh Afzali

Designing an appropriate tunnel blasting pattern reduces the cost of rock breakage and subsequent operations such as loading, haulage and support of tunnels. For that reason, we developed a software that designs tunnel blasting patterns. Using this software, three different tunnel blast design models based on parallel hole cut, namely, Swedish, Konya and Energy Balance, were investigated and compared for a virtual tunnel. Accordingly, blasting patterns were designed, for different cross sections. The trend of parameters such as specific charge and specific drilling as functions of tunnel cross-section was determined for each model. Our results show that, in general, The Swedish model gives lower specific charge and specific drilling compared to other models.

Jan 1, 2008

By B. Ladanyi

An adequate knowledge of the overall behavior of a rock mass at a given site is fundamental to the satisfactory design of a rock slope. The be- havior is controlled by a variety of factors, in- cluding rock type, geological structure, stress and ground water conditions. There are essentially three lines of approach that may be used to obtain information on the in-situ rock mass behavior for the purpose of the design of a rock slope: (1) Direct measurements of rock mass properties by means ol laboratory and field tests. (2) Evaluation of rock mass properties from a study of slope failure case histories and sta- tistical information on stable and unstable natural rock slopes. (3) Evaluation of in-situ behavior of rock mass by using a physical or mathematical model technique.

Jan 1, 1980

By AIME AIME

The American Society of Mechanical Engineers.-The semi-annual meeting of the American Society of Mechanical Engineers will be held in Detroit, Mich., June 23-26. A session will be devoted to hoisting- and conveying-machinery; and many other subjects will be treated in professional papers, among which are . Clutches (with special reference to automobile clutches); The Thermal Properties of Superheated Steam; The Horse-Power, Friction-Losses, and Efficiency of Gas- and Oil-Engines; A Journal-Friction Measuring-Machine; A Simple Method of Checking Conical Pistons for Stress, and The By-Product Coke-Oven. The usual receptions will be held and excursions will be made to manufacturing plants, the slip-building yards, and various points of interest in and around Detroit. Among the excursions' planned is one to the University of Michigan at Ann Arbor. The Gas-Power Section of the Society will hold a session, and the Society for the Promotion of Engineering Education and the Society of Automobile Engineers will hold meet-

Jan 5, 1908

By George C. Stone

Since the Troy meeting I have received several additional results of analysis of the same sample of spiegel, which I give below: P. I know only by correspondence. His methods are : for results Nos. 47, 48 (13.03, 13.26) dissolve In hydrochloric acid, evaporate, oxidize with nitric arid, filter from silica, separate iron as basic acetate, precipitate manganese as sulphide, dissolve in hydrochloric acid; and precipitate as carbonate. No. 49 (13.72) was obtained by Eggertz's method. Nos. 50, 51 (13.10, 13.10) were dissolved and oxitfized as before, the iron precipitated by oxide of zinc, filtered and washed four times with cold water; and the manganese titered hot with permanganate. P. regards these two results as low. Nos. 52, 53 (13.75, 13.69) were dissolved and treated like the last two, the precipitated iron was again dissolved, separated, and titered as before; the results are the sum of the manganese joined in both

Jan 1, 1884

By Mengxiong Guo, Xuxin Shao

The recent depressant research is summarized, and a new kind of depressant (SCO) has been put forward in this article. Using Na-oleate as a collector and SCO as a depressant, separation of dolomite and phosphate was studied. When SCO was added in the concentration range of 80 g/t to 2kg/t at pH 9.5 ± 0.2, dolomite was absolutely depressed, and apatite kept its floatability. Interestingly, in the mixture of phosphate and dolomite, the dolomite floated. The reasons for such a behavior are investigated through flotation and electrokinetic studies. It was found that the adsorption of dissolved species on dolomite and phosphate resulted in reverse flotation. A concentration of 31.59% P205 and 83.87% recovery of P205 was obtained from the mixture of phosphate and dolomite (2:1) with 26.6% P205 using 210 g/t SCO and Na-oleate 4.93*10-5 M at pH 9.

Jan 1, 1989

The Fosterville Goldmine in Victoria employs bacterial oxidation (BIOX« Process) to liberate gold from its flotation concentrate. Gold occurrence is primarily as submicron particles in pyrite and arsenopyrite and has been described as being in æsolid solutionÆ and therefore not amenable to direct cyanidation even with fine grinding. Once liberated by the oxidation process, the gold is then available for cyanide leaching. While the oxidation process is very effective, it has been found that a portion of the liberated gold can become suspended in the liquid phase in what appears to be a colloidal state. This liquid becomes a waste stream during washing of the oxidised solids and the suspended gold is therefore lost. This paper discusses investigations into the causes of the loss and also describes the successful use of quebracho tannin in reducing colloidal gold loss. Laboratory and subsequent plant trials, showed a gain of 2.6 per cent in overall gold recovery based on mill feed and waste stream data.

Jan 1, 2009

By J Penman, N Turner, H Liu

This paper aims to present a snapshot of the risk profile for tailings storage facilities within Western Australia by comparing the spatial distribution of known facilities against common geohazards such as cyclonic activity, climate, and peak ground accelerations from earthquakes. The analysis also includes an assessment of proximity to populations at risk including towns and sensitive receptors including significant river systems and wetlands.

Jul 1, 2021

By G. A. Savanick

Borehole (slurry) mining, where a tool incorporating a water-jet cutter and a downhole slurry pump mines phosphate through a borehole, was field tested in northeastern Florida as part of a US Bureau of Mines program to increase the domestic availability of critical minerals. About 1.5 kt (1700 st) of phosphate ore were mined at 23.6 t/h (26 stph) from a depth of 76 m (250 ft). The borehole was filled with water during mining for roof support and to assist slurry pumping. Underwater cutting was enhanced with an air-shrouded water jet. Mined cavities were backfilled to prevent subsidence after abandonment. Roof subsidence during mining was avoided only when the cavity was filled with water. Environmental monitoring before, during, and after mining included hydrological studies and measurements of water quality. Significant water quality changes occurred only in the zone being mined and were confined to the immediate area of the borehole.

Jan 1, 1986

By William E. Ford, Edward Salisbury Dana

1. Normal Class (25) Barite Type 2. Hemimorphic Class (26) Calamine Type 3. Sphenoidal Class (27) Epsomite Type Mathematical Relations of the Orthorhombic System Crystallographic Axes. - The orthmhombic system includes all the forms which are referred to three axes at right angles to each other, all of different lengths. 296 Any one of the three axes may be taken as the vertical axis, c. Of the two horizontal axes the longer is always taken as the b or macro-axis * and when orientated is parallel to the observer. The a or brachy-axis is the shorter of the two horizontal axes and is perpendicular to the observer. The length of the b axis is taken as unity and the lengths of the other axes are expressed in terms of it. The axial ratio for barite, for instance, is a : b : c = 0'815 : 10 : 131. Fig. 296 shows the crystallographic axes for barite.

Jan 1, 1922

By R. A. Jankowski, J. D. Potts

Four underground respirable dust surveys were conducted to determine factors affecting belt entry dust levels and how using belt air to ventilate work areas affected dust exposures. Belt entry dust levels on the surveyed longwall and continuous miner section averaged 0.59 and 0.26 mg/m3, respectively. The stageloader/crusher contributed an additional 0.5 to 0.9 mg/m3 of dust to belt air, while the feederbreaker contributed 0 to 0.2 mg/m3 of dust. A 1000 ft (305 m) increase in belt entry length or a 200 to 500 tons/shift (181,000 to 454,000 kg/shift) increase in production resulted in roughly a 0.1 mg/m3 increase in dust. Using the belt entry as an intake entry on the continuous miner section appeared to reduce dust levels by 0.1 to 0.3 mg/m3 during cutting. Belt air was not used to ventilate the face on the longwall section.

Jan 1, 1992

By Michael G. Pojar

This Bureau of Mines report estimates the population of the principal types of machinery in use by the coal mining industry during 1982 in surface and underground mines. Estimates were arrived at using 1976 coal equipment population estimates as baseline data with modifications made for new mine development, expansion, and closure occurring during 1976-82. Estimates were broken down into 3 regions which included all 26 coal-producing States. Modifications made to the baseline data were computed using (1) actual equipment information when available, plus (2) equipment information hypothesized from representative generic mine models, which were predicated on mine size and mine method. Roughly half of the equipment fleet at new or expanding coal operations was known; the remainder was hypothesized. The mine models used to generate equipment information are included in this report, along with the hypothesized equipment use data. The equations and various factors used to determine the equipment adjustments for mine closings, new mine openings, and small coal mine operations are also identified.

Jan 1, 1986

By M. A. Giralico

A new generation of hydraulic efficient pumper and auxiliary impeller designs is the result of an extensive research program focused on improving the overall performance of optimized SX/EW plants. Combined with the proper scale-up, these optimized designs will greatly reduce aqueous and organic entrainment losses, reduce or eliminate air entrainment and crud formation, enhance mass-transfer and maximize the overall copper yield. Currently, these new pumper and auxiliary impellers are installed full-scale in numerous plants ranging in flow rates from 90 to 15000 G.P.M. and developed heads up to 51 inches. Operational results reported by the independent metallurgist at each processing plant are reporting the lowest entrainment results in the industry. Further R&D has just been completed on a new mixing configuration that separates the systems mixing and pumping requirements. Results from the system pilot test document further improvements in reduction of both chemical entrainment and crud formation, while keeping mass transfer stage efficiencies.

Jan 1, 1998