Search Documents

By R. L. Whiting, H. J. Ramey

The basic study from which this paper was prepared was started as the result of the growing need throughout the world for increasing quantities of energy in all forms. Quite obviously, natural forms of energy that are readily available at low development cost are those in greatest demand. The underdeveloped countries — and particularly those having little or no petroleum resources — are the countries in which the most interest is being shown in the newer energy sources. One of the least expensive energy sources is natural geothermal steam.'-* Although this form of energy has been recognized for centuries, it has been only during the past 20 years that serious efforts have been made to harness it. Natural geothermal steam energy in Italy, New Zealand, Mexico, Japan, and California is now being produced through wells to drive turbines and generate electricity. Further, active exploration for natural geothermal steam is being conducted in Hawaii, Fiji, Taiwan, Chile, Russia, Greece, and Katanga. It is surprising to find that most geothermal steam exploration is in the "steam seep" stage. That is, surface studies are made and exploratory wells are drilled in the general area of steam seeps. However, in the larger geothermal steam areas, there have been efforts to apply the most modern geological and reservoir engineering principles in order to define the reservoir parameters, particularly those relating to estimates of reserves and future productivity. This paper is concerned with the development of appropriate equations and techniques to facilitate these estimates. Production of natural steam or hot water presents problems different from those experienced in the production of oil and gas. For example, steam or hot water systems may be essentially single-component systems, while hydrocarbon systems are most frequently multicomponent fluid systems. Heat effects are much larger for water than for hydrocarbon systems; and the natural steam production may or may not be isothermal, while production of petroleum reservoirs is considered normally to be isothermal. Petroleum reservoir engineering principles may be applied to natural steam or hot water reservoirs if the inherent differences in the systems are considered. The basic considerations involved in geothermal steam reservoir engineering are: thermodynamics, physical and thermal properties of water, materials and energy balances, fluid influx, and performance matching and predicting. Thermodynamics Fig. 1 is a pressure-temperature diagram for the liquid-vapor region for pure water, showing the critical point and five other points representing possible initial conditions for a geothermal steam reservoir. To generate a physical appreciation for the mechanics of natural steam production, it is helpful to consider

Jan 1, 1970

By John V. Beall

BROMO Seltzer blue has gone to war. The blue of the Bromo Seltzer bottle is a product of cobalt, the Nation's No. 1 strategic metal. When the National Production Authority, on Nov. 21, 1950, ordered a 70 pct cutback in domestic use of cobalt, a stab of pain was felt in the hearts of the glass, porcelain enamel, steel, paint, pottery, and electrical and electronic equipment industries. The reason: A full-scale wartime economy with astronomical requirements for jet engines, high velocity projectiles, armor plate, electronic equipment, and the many products needed to win a war. There is little potential comfort for cobalt users in nonessential manufacturing, and the military will be pinched for optimum supplies of the metal. However, if proper measures are taken immediately and current plans are completed, in two years there will be far more cobalt available than ever before. When normal times return, cobalt supplies should be sufficient to meet peacetime military requirements, and greatly expanded domestic requirements that will result from new technological development for wartime but adaptable to peacetime products. The pres-

Jan 1, 1951

By The Staff

BEFORE going into detail on the subject to be presented, a brief outline of the Company's earl y history would not be out of place. Prospecting and mining on a small scale was started in 1876 on the site of the present open pit at Thetford Mines. The property was purchased from the Crown in 1878 and Johnson's Company was incorporated in 1885. It is owned and operated today by descendants of the original shareholders. Many employees, through their fathers and grandfathers, have service records dating back three generations. The principal asbestos deposit at Thetford Mines is pear-shaped, with surface dimensions of about 2,200 feet in length by 1,300 feet in maximum . width. Its long axis strikes northeast and the dip is nearly vertical, but irregular in detail. It is known to extend to a depth 1,200 feet below the original surface, but its area at that depth has not been determined. Ownership of this deposit is divided among three active Companies: the Asbestos Corporation, Limited; Bell Asbestos Mines, Limited; and John-son's Company. Johnson's Company owns a section about 1,000 feet in length and 500 feet in width, bounded on the northeast by the King mine of the Asbestos Corporation and on the northwest by the Bell pit. On Johnson ground, there was originally a large outcrop o~ asbestos rock which dipped toward the south below overburden. This was mined until recently by open pit, the overburden being stripped off as far southward from the original outcrop as was economically possible. As the. pit was deepened, within side walls maintained at a maximum safe slope, its floor area, of course, became progressively smaller, and eventually the pit would have wedged out against the Bell property line. It became necessary, there-fore, to introduce some other method of mining before production became seriously curtailed by a shrinkage of the pit area.

Jan 1, 1941

By Jay R. Schafler, Jacob L. Brinkman, Catherine E. Johnson

"The United States coal mining industry is currently experiencing a decline in both demand and commodity price while facing implementation of more stringent air and water pollution regulations. Company profits have decreased significantly, forcing several major companies to declare bankruptcy. The industry was required to adapt to survive. Many of these companies have adjusted by abandoning mines; the last two decades have seen a drastic decrease in the number of mines. To discover the primary causes of this downturn, three major aspects must be studied: properties of abandoned mines, commodity history and regulatory impact. Trends since 1994Each year, U.S. coal mines are required to submit data on a variety of categories to the U.S. Mine Safety and Health Administration (MSHA) and the U.S. Energy Information Administration (EIA). This data include administrative records, production values and information regarding the attributes of the mined material and the mine itself. Each year since 1996, EIA has released a report summarizing the data from two years prior. Additionally, MSHA maintains a database containing a collection of all the most current data. These resources are the primary sources for the figures included in this article. There are several items to note regarding this data:1. The EIA reports from 2016 and 2017 were not released at the time of writing this report.2. The MSHA data set is actively maintained as information is provided. This means the data for 2016 is from June 27, 2016 and data for 2017 is from Aug 24, 2017. All other points represent the end of-year values.3. Each of the figures only includes data pertaining to active mines. EIA defines active mines as both active and temporarily idled mines, and inactive mines as nonproducing and abandoned mines. MSHA separates all four into separate categories, though this paper combines the MSHA values according to the EIA definition for the purpose of comparison."

Jan 10, 2017

By D. Hodouin

Jan 1, 1978

By A. H. WHITE, PERRY BARKER

In a consideration of the various means whereby more economical and more efficient use may be made of the fuels in the United States, the possibility of obtaining for the production of illuminating gas other and cheaper fuels than the Pennsylvania coals demands attention. For the Government, as well as for private corporations and the householder, there can be no more economical and efficient way of using some coals than through the medium of illuminating gas. In the stove, gas reduces the labor cost of heat production and lessens the drudgery of the kitchen; burned in the Welsbach mantle, it is an excellent and cheap illuminant. In addition, the coke that remains after the gas has been recovered furnishes a smokeless fuel that has about the same heating value as anthracite. Hence any investigations that will indicate how local coals through proper treatment may be substituted for the higher priced and rapidly vanishing Pennsylvania gas coals will bring about lower prices for both gas and coke and will also aid to conserve for use in metallurgical processes the coking coals of Pennsylvania and of ot,her States. The annual drain on the gas-coal resources of this country and the importance of the gas and coke industries are indicated by the fact that 8,390,129 tons of coal were carbonized in retorts in the United States in 1909. The resulting salable products from by-product ovens were 15,791,220,000 cubic feet of coal gas, 6,254,644 tons of coke, and 60,126,000 gallons of tar. The total value of all by-products was about $28,508,637.

Jan 1, 1911

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck, Y. Zheng

Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27 percent of respirable coal mine dust can be attributed to longwall shield movement, and developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine the ability of the foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used: compressed air and blower air. Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For compressed air foam in 3.3 m/s (650 fpm) ventilation, 98 percent of agent A was intact while 95 percent of agent B was intact on the roof at three minutes after application. At 30 minutes after application, 94 percent of agent A was intact while only 20 percent of agent B remained. For blower air in 3.3 m/s (650 fpm) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 min after application, 74 to 92 percent of foam agent A remained, while 3 to 50 percent of foam agent B remained. Compressed air foam seems to remain intact for longer durations and is easier to apply than blower air foam. However, more water drained from the foam when using compressed air foam, which demonstrates that blower air foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able to withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control.

Jan 1, 2017

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck, Y. Zheng

Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27 percent of respirable coal mine dust can be attributed to longwall shield movement, and developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine the ability of the foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used: compressed air and blower air. Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For compressed air foam in 3.3 m/s (650 fpm) ventilation, 98 percent of agent A was intact while 95 percent of agent B was intact on the roof at three minutes after application. At 30 minutes after application, 94 percent of agent A was intact while only 20 percent of agent B remained. For blower air in 3.3 m/s (650 fpm) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 min after application, 74 to 92 percent of foam agent A remained, while 3 to 50 percent of foam agent B remained. Compressed air foam seems to remain intact for longer durations and is easier to apply than blower air foam. However, more water drained from the foam when using compressed air foam, which demonstrates that blower air foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able to withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control.

Jan 1, 2018

By P. Anyon

Exposure to the microscopic particles in diesel engine exhaust can lead to serious health problems, including the incidence of cancers, heart disease and increased susceptibility to respiratory ailments such as pneumonia, bronchitis, and asthma. In Australia, mining companies and state government authorities are actively responding to this major occupational health and safety issue. Their initiatives place considerable emphasis on routine monitoring of diesel particle matter (DPM) exhaust emissions, both for engine benchmarking and as a part of routine engine maintenance. Implementation strategies follow two complementary paths: determination of individual engines? emission signatures combined with periodic engine re-certification; and co-operatively agreed industry-government engine maintenance programs, which are subject to audit. Both strategies place heavy reliance on real-time measurement of DPM concentrations in engine exhaust, using ruggedized instrumentation, mainly based on laser light scattering photometry. Adding value to this cooperative approach, industry has also collectively funded a government agency to design and manage a database, into which the results of all-routine DPM testing can be uploaded directly by individual mines. This win-win outcome is a great example of how cooperative action between governments and industry can deliver the goods: in this case, a safer working environment, more efficient energy use and the capacity to benchmark performance with industry peers.

Jan 1, 2009

By B Belle, M Biffi

Cooling of coal mines in the Bowen Basin, characterised by steep geothermal gradient, is presently achieved mostly through rental surface bulk air cooling in summer months. This paper argues that future mines will be required to focus their cooling resources more intensively to manage a challenging thermal environment where virgin coal temperatures of over 50¦C at a depth of 500 m are expected. Currently, mine cooling systems are employed to maintain the wet bulb temperatures (WBT) to below 27¦C at which point the risks of heat stroke or other heat-related issues are manageable. The capacities of these systems are in the range of 6 MWR to 10 MWR. The relationship between high working temperature environments and injury frequency rates is well established. Therefore, provision of appropriate cooling strategies and understanding their optimum performance and suitability are important to Australian coal mines of the future. This paper evaluates the underground temperature profiles of deep, gassy coal mines with propensity for spontaneous combustion and proposes the long-term cooling pathways to effectively manage thermal hazards. Thermodynamic modelling is performed on a longwall face and includes air leakage effects from goaf streams at various locations along the longwall face. The strategy summarises the application of underground bulk air cooling, chilled water sprays on the shearer and the resulting temperature profiles. Considering the new mining projects planned for the Bowen Basin region, a review of implementable cooling strategies such as mid-gate mobile bulk air coolers (BACs), spot coolers, underground bulk air cooling and the use of chilled water to enhance the positional efficiency of cooling plants, are discussed in this paper. Finally, the comparison of ærentalÆ versus æownershipÆ of cooling plants is analysed as part of long-term cooling strategies.CITATION:Belle, B and Biffi, M, 2013. Cooling pathways for deep Australian longwall coal mines of the future, in Proceedings The Australian Mine Ventilation Conference , pp 223-236 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By J Jackson, E Sellers

Blasting related indices were developed to quantify variation in rock strength and structure for each stope, and for each lift of each stope, as part of a Mine to Mill study at an underground open stope mine. The indices were derived from combinations of data from underground diamond drilling because the simplifying assumptions contained in the block model prevented sufficient differentiation in rock mass characteristics to enable adjustments to the blast design.Application of combinations of blasting related indices enabled the identification of stopes with a high potential for inconsistent and oversize fragmentation, underbreak and overbreak. The indices also fragmentation outcomes to deliver increased material flow within stopes, better digability and predict indicative mill throughput. The stopes with issuesCalibration of the results enabled adjustments to the blast design based on the rock mass conditions and accordingly improved the blast outcomes. This enabled improved productivity by reducing underbreak and overbreak, having a more appropriate fragmentation, which reduces unplanned rock handling and improves bogging. The reduction in recovery drilling creates huge opportunities to improve output by reducing production delays and decreasing the overall cost per tonne. By understanding the explosive performance and blast energy distribution in relation to rock mass blastability poor, performing designs in blind upholes and convex stopes were identified.The conclusion of the work is that value improvement, regarding increased revenue and reduced costs, can be achieved across the whole underground Mine to Mill process chain by developing stope based indices from the existing geological information to correctly tailor the blast design to the rock within, and surrounding, the stope.CITATION:Jackson, J and Sellers, E, 2017. Blasting related indices as the key to underground blasting improvements in a challenging rock mass, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 23–32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By William Gleason

"There are few people more qualified to speak of the tumultuous times in the global mining industry during the past four years than Newmont Mining Corp. president and chief executive officer Gary Goldberg.Goldberg stepped into his current position in 2012, just before MINExpo 2012. Gold prices had hit record highs not long before that ($54.15/g or $1,856.40/oz on Sept. 8, 2011), expansions were happening around the world and the gold mining sector was still living in the glow of one of its longest upswings in history.That all changed between April 8 and April 15, 2013 when the price of gold dropped by nearly $200/oz ($46.27/g or $1,586.20/oz on April 8 to $40.45/g or $1,386.80/oz on April 15), putting an end to the decade-long mining boom and forcing mining companies like Newmont to re-evaluateeverything.Three years later, with the gold sector recovering, Newmont Mining is not only surviving but is thriving with a pair of mines coming online, Long Canyon in Nevada and Merian in Suriname. On Oct. 1, the Merian Mine went into production on time and more than $150 million under the initial development capital budget.Goldberg, who was one of the featured speakers at the opening session of MINExpo International 2016 on Sept. 26, also spoke with Mining Engineering about the previous four years and the future of the industry.“Mining goes through cycles all the time and gold is no different,” Goldberg told Mining Engineering when asked about surviving the downturn since 2012. “I thought it was important that we take a good methodical and steady approach across the business to determine what was the right thing to do and to set the business up to improve performance. Anyone can cut costs for the short term, but we set out to do it in a sustainable and reliable way. We created a program we call Full Potential to look for sustainable ways to reduce costs and improve productivity. That program has taken more than a billion dollars out of our costs since we implemented it 2013 and that shows up in our results. Our all in sustaining costs are down 28 percent and our productivity is up 39 percent.”During the downturn, Newmont restructured its business model, sold off some assets and created a leaner, more nimble operation. It has paid off with the addition of two new mines and the acquisition of another, the Cripple Creek & Victor Mine in Cripple Creek, CO.“The gold industry had not seen a downturn in 12 years. We had half a generation that had not experienced a downturn, so helping them through that in an organized way and keeping a view toward the long term throughout the downturn was important. We were one of the few companies that continued to invest in assets,” he said."

Nov 1, 2016

By J. Paraszczak

Underground metal mining involves many challenges. Economic slowdown, tough international competition and sometimes volatile metal prices put constant pressure on mine operators to increase productivity and to reduce production cost. At the same time, countries such as Canada, the United States and Australia are experiencing skilled labor shortages that might even stall development of certain mine projects. Furthermore, some stages of underground production take place in particularly hazardous environments where the safety and health of miners is at risk. Automation of some processes in underground mining is one of the promising avenues to alleviate some of these problems. Loading and haulage are among the most critical operations and areas where implementation of autonomous vehicles has been targeted. However, although health and safety issues are a primary driver to opt for automation, the latter should ensure an acceptable level of productivity and pro?tability. With this in mind, this article focuses on the factors affecting operational effectiveness of autonomous underground loading and haulage equipment and the means to maximize it.

By Philip Morey

Large scale surface coal mining will be required to fill future energy demand in the United States. In realization of this long-term commitment to coal resources, the U.S. Energy Re-search and Development Administration sponsored a study to determine the costs and problems of large-scale surface coal mining. As a result of this study a series of computer models were developed that can be used by government and industry to: 1) facilitate mine design and equipment selection, 2) provide detailed analyses of mining and processing costs. Two types of models were developed: detailed simulation models, which provide detailed information on mining systems and equipment to assist in mine design and equipment selection1 and broad models, which provide a first-order evaluation of deposits and new ventures for an entire mining complex. The complete model series permits examination of surface coal mining under a variety of terrain conditions. Six different mining methods were analyzed and documented during the overall project: 1) Area stripping with draglines, 2) Area stripping with draglines, extended bench, 3) Contour stripping with draglines, 4) Area stripping with shovels (loaders) and trucks, 5) Mountain top removal with shovels (loaders) and trucks, 6) Multiple dipping seam mining with shovels (loaders) and trucks. Each major operation in the coal mining pro-cess is represented in these models so that the best methods and equipment may be selected and 50 that the impact of such selection will be reflected in estimates of capital investment, operating costs, and coal price. Individual models allow the user to separately analyze overburden removal, overburden drilling and blasting, coal drilling and blasting, coal loading and hauling, coal preparation and handling, land reclamation, and premining, facilities, and administrative expenses. Because it is impossible to cover all the models in this paper, only the detailed simulation models representative of the technique "area stripping with draglines," are described. The Fort Union Strippable Coal Resource Region, one of eight test cases, is used as an example to describe the models.

Jan 1, 1978

By Richard Lusignea

A single boom roof bolting machine was outfitted with measurement and recording systems for detecting changes in machine parameters while drilling. The purpose of this instrumented bolter or "smart drill" is to detect changes in roof conditions from the machine parameters of penetration rate, thrust, rotation rate, torque, rejected light from rock cuttings, and vibration of the roof during drilling. The system was demonstrated underground in coal mine conditions and showed correlation between rock type and drilling parameters.

Jan 1, 1982

By George A. Burrell, Frank M. Seibert

The Bureau of Mines, as part of its designated duty of investigating the causes of mine accidents, is conducting at its experiment station in Pittsburgh, Pa., a study of mine gases. Some of the work already done in connection with this study is outlined below. A large number of mine-gas samples have been collected under normal conditions in returns and in splits, and at other points in the ventilating current, also at the face, in the goave or gob, in unventilated places, and wherever the air was still. Samples have also been obtained under abnormal conditions, as after explosions and while mine fires were in progress, or from sealed areas behind stoppings and darns where the air had been stagnant for some time. Chemical changes in the composition of mine atmospheres during mine fires have been studied," and conditions peculiar to certain mines have been investigated. The question of the effect of a change in atmospheric pressure on the escape of gas (methane) in coal mines has been studied. Explosives have been fired in both coal and metal mines, and samples of resulting gases have been collected to ascertain the degree to which these gases vitiate the air. A series of samples in mines where gasoline locomotives were being used have been examined in order to ascertain the degree to which the exhaust gases from such locomotives foul the mine air. Experiments have also been performed in regard to the relative effect of carbon monoxide b upon men and small animals. A preliminary report relating to the inflammable gases in mine air has been published. Full reports of the results of the investigations outlined above will be published as soon as all the necessary data have been gathered. The first part of this report deals with the methods used by the bureau in the collection and examination of the various mine gases; the latter part discusses the bureau's methods of sampling and examining natural gas.

Jan 1, 1913

By D. L. Morgan, J. A. Butterfield

"Geological data, production trends and current projects underway suggest that enough molybdenum will be available from more diversified sources to meet the world's growing demands. The growth in molybdenum consumption has been primarily related to its beneficial effects as an alloying agent in steel. This rapid growth has been deliberately fostered by stable prices, adequate supply and application research. The molybdenum industry is now in a process of change which has been seen in several other metals, such as aluminum and nickel. As supply sources have become more diversified, the market has become more competitive. The recent drop in consumption has led to excess production capacity, accumulation of substantial producer inventories and increased market uncertainties. While consumption is expected to increase in the next two to three years, it will take some time to absorb the excess capacity and inventory. The increased proportion of by-product capacity indicates that prices may become more variable. Producer discipline will be required to prevent serious price erosion in times of surplus. Future prices may not continue to increase with inflation. For the longer term, several factors favour the increased consumption of molybdenum. Engineering requirements are becoming more severe and molybdenum alloys can help to meet these changing needs. In addition, consumers can rely on a large and increasing supply of molybdenum. A 7 per cent growth rate in consumption can probably be sustained through the next decade, but new applications and reasonably stable prices will be needed to make this possible."

Jan 1, 1972

By J. R. Thoenen

This paper outlines briefly results of seismic measurements recorded in the vicinity of quarry blasting under practical operating conditions. The data cover field work done from January to the middle of August 1930, during which time records were made of 61 blasts in 19 quarries. Of the tests made, one was in biotite-gneiss, two in dolomite, two in a flintlike volcanic complex, three in gabbrodiorite, five in trap rock, and six in limestone. One quarry was in Alabama, two were in South Carolina, two in New York, four in Kentucky, five in Connecticut, and five in Massachusetts. Explosive charges ranged from 0.30 pound to 41,900 pounds, and the method of shooting varied from mud caps through hammer and wagon drill holes to churn drill holes and coyote tunnel shots.

Jan 1, 1937

By A. E. Michon

I am Alfred E. Michon, Vice President- International for Burlington Northern Inc. I work for BN's holding company and my responsibilities include co-ordinating the activities of our eight subsidiary companies as they relate to international commerce--an increasingly important aspect of the overall business of our company. Until last April, I was President of the Fort Worth and Denver and Colorado and Southern railroads, subsidiaries of BN. Prior to that, I headed the marketing and pricing area of BN's coal transportation business. Based on my experience in the energy industry, both domestic and international, I would like to discuss the world-wide trend towards the reliance on low-sulfur coal in lieu of natural gas and oil for the generation of electricity. Since pontification on the energy scene world- wide is best left to consultants with scenario-spitting computers, let me in- stead emphasize this trend through two examples. First I will describe the regulatory and economic factors which have encouraged the replacement of natural gas by low sulfur coal as a boiler fuel in the US. BN's investments in track and equipment were instrumental in this conversion. Secondly, I will show how this same combination of factors has created a large demand for steam coal in the Far East. Again, our company's strategy is to facilitate conversion to coal overseas through timely and sufficient investments.

Jan 1, 1982

By Oliver Bowles

ASBESTOS is a name applied to a group of naturally fibrous minerals. As indicated in a later section devoted to a detailed discussion of the early history of asbestos, the tern may be defined as a. fibrous form of serpentine or amphibole. It does not include fibrous forms of other minerals, such as wollastonite, nemalite (fibrous brucite), or the fibrous forms of calcite or gypsum. A material that has the characteristics of silk or cotton and at the same time will not burn is unique. Because it combines these qualities with other advantageous properties, asbestos has specialized uses for which no substitutes are yet available. Asbestos furnishes a major raw material for a great variety of essential products and their manufacture constitutes a vast industry. The United States leads all countries in the manufacture of asbestos products. The value of such commodities manufactured in 1952 exceeded $332 million. They are not only of vast importance to budding construction and industry but axe absolutely, essential to certain important fields of use, for example, steam packings and friction materials, such as brake-band linings on automobiles.

Jan 1, 1955