Search Documents

By Chu E. Ho

This paper reviews the design of jet grouting at re-entrant corners of excavations where the diaphragm wall and secant pile wall installation were interrupted by existing utilities in the streel sidewalk. Jet grout blocks were formed to seal the gaps in the walls for excavation support, consisting of four to six columns in clusters. Jet grouting was performed around an electrical duct bank which had to be maintained. Jet grouting was executed through stratified soils using various combinations of jetting parameters for different soil strata. The installation sequence and age of the neighboring columns within a cluster will affect the jet’s ability to form subsequent columns. When jet cutting is limited next to hardened grout columns or embedded obstructions (such as diaphragm walls or secant pile walls in this case), the specific gravity (SG) of spoils would be reduced and tend toward the value of the injected grout SG. The magnitude of spoil SG is also influenced by the variability of the grout mix supplied. Specific Gravity Ratio (SGR) defined as the ratio of spoil SG to the actual grout SG at the time of jetting can be used as an indicator of successful treatment, with SGR > 1.0 indicating effective soil erosion. Verification coring and testing were implemented to confirm target column diameter and strength of grouted soils have been achieved.

May 1, 2022

By M. Onifade, B. Genc, P. O. Akinseye, M. Fourie, K. O. Said

Coal is mined by both surface and underground methods and its extraction is normally characterized by numerous hazards that can lead to catastrophic accidents, which result in devastating effects such as injuries or fatalities, damage to mining assets, and destruction of mineral resources. These hazards exist due to the ability of coal to support combustion and its association with toxic, flammable, and explosive gases. Underground coal mining entails higher safety risks than opencast coal mining, chiefly because of issues relating to mine ventilation and mine collapse. Furthermore, coal mine collapses mostly occur due to crumbling of mining supports, especially in room and pillar mining systems. To avoid such adverse occurrences, safety management systems need to be in place. This study reviews the various technological safety systems and principles that are used for safe-rescue and self-escape of miners in underground coal fires, particularly in South Africa, using data obtained from Mines Rescue Services in Carltonville, South Africa. The outcome of the review shows that practising safety culture has been given priority across many South African underground coal mines through setting up safety management systems and encouraging workers to stay committed to safety principles.

May 2, 2022

By Marc Boyer

Modern civilization, modern industry, and modern standards of living, bring into, sharp relief the present-day essentiality of metals .and minerals, and the wide and diversified use which is made of them. Any attempt, therefore, to appraise the international situation today must take into consideration the metal and mineral resources of the world. If, as some believe, the world is divided into two distinct ideologies of political belief, one unalterably opposed to the other, so that armed conflict is unavoidable, then the question of national strength in mineral resources becomes of paramount importance. If, however, it is possible to avoid war by raising the standard of living in the underdeveloped ?areas of the world, thus ensuring all peoples everywhere against the dread spectres of starvation and disease, then the development of the world's mineral resources assumes even greater importance. Today it is difficult to realize that, prior to the industrial revolution in Great Britain, only a few of the metals and minerals now in common use entered into the everyday life of the people. !iron and steel, copper, lead, tin, and zinc, usually in .their unalloyed forms, along with the more common industrial minerals, were those most widely used, and then only in limited amount. With the advance of technology in metallurgy and in fabricating skills, the list of commercial metals and minerals has expanded until today they number more than eighty.

Jan 1, 1951

By Bruce Geller

Attending the Prospectors and Developers Association of Canada (PDAC) meeting and exhibit has become an annual tradition for many in the mining industry. Similar to last year’s synopsis, this report is an overview of the 2003 conference from the eyes of a consulting mineralogist. It is supplemented by conversations with other participants. And it examines the conference handouts. Certain segments of the mining industry have seen improvement throughout the year in terms of metal prices, stronger demand and renewed interest by the investment community. Other segments continue their decline due to depressed commodity prices, higher oil prices, a continued weakness in the global economy and war uncertainties. SARS was known to the world, but it was not a Toronto epidemic during PDAC. In short, this year’s PDAC was permeated by an air of anxiety about the Middle East.

Jan 1, 2003

From the massive equipment that moves the earth, to the parts that keep the equipment moving, it was all on display for more than 35,000 people who at-tended MinExpo 2008 at the Las Vegas Convention Center Sept. 22-24. In the largest show in the illustrious history of MinExpo, the success of the recent commodity boom was reflected in the more than 55,700 hm2 (600,000 sq ft) of floor space that was jam-packed with nearly 1,300 vendors. Among them, the makers of the industry?s largest machines, displaying their latest and greatest trucks, shovels, excavators, drills and other mining equipment. During the nearly decade-long commodities boom, equipment makers have worked hard to keep up with demand while also investing heavily in research and development. The beneficiaries of this R&D is the end user who saw first-hand at MinExpo 2008 the many advances that have already been made in safety, comfort and productivity from all the manufacturers. R&D has also helped spark more talk of automation, which is being used already at some of the world?s largest mines. Caterpillar and Komatsu have worked with the technology in surface mining and Bucyrus and Sandvik are among the industry leaders applying the science of automation to underground mines. Technology has in-creased greatly since the idea of moving massive equipment remotely was first knocked around and the idea of entire fleets operating around the clock seems to be getting closer to reality. But, until that happens, MinExpo attendees were treated to a show that featured some of the most impressive current machines the industry has to offer. In the largest booth space of the convention, Caterpillar (www.cat.com) displayed the culmination of an ambitious $280-million dollar investment, with the introduction of its new mining fleet of four new trucks. The F-series was un-veiled with common features in safety, cabs, engines, frames and bodies and Tier 2 compliant engines. The F series also features a return to the electric drive option. ?When our customers asked us for improvements to our mining trucks, we responded by making a record investment in every single truck in our line, as well as the increased capacity to produce more of them,? said Cater-pillar group president Stu Levenick. ?New technologies have allowed us to make trucks more reliable, easier to maintain and more friendly to the operator and to the environment.? The 793-series is in the 218- to 227-t (240- to 250-st) class that will be available in both mechanical (793F) and electric (793F ac) versions. The electric drive-only 313- t (345-st) 795F was also introduced, while the flagship 797B truck is in the process of being replaced by the new 797F mechanical drive, maintaining its 345- to 363-t (380- to 400-st) target payload. Completing Caterpillar?s new mining truck line will be new versions of the 785 and 789 mechanical drive trucks. The next generation of trucks will be phased into production during the next two years, with the Cat ac drive models expected to go into production in late 2010. The $280-million in-vestment is Caterpillar?s largest commitment ever to the mining industry

Jan 1, 2008

By T. Strong

"Selectively recovering pentlandite from high levels of pyrrhotite presents a technical and operational challenge. The liberation characteristics and also the chemical environment is critical to performing a successful separation. Reviewing the mineralogy to understand the characteristics of the ore and the plant flotation behavior is fundamental to designing a successful improvement program.At Savannah Nickel the challenges presented by a falling nickel price required a rethink of the flowsheet to improve the project economics through improving the concentrate grade and recoveries. Glencore Technology reviewed the plant performance and proposed and tested solutions to improve the grade performance of the concentrator with the support of the plant team. A pilot plant comprising a M20 IsamillTM followed by an L500/1 Jameson Cell was operated on various plant streams. In addition to the pilot plant, flotation surveys and a plant based laboratory program was used to supplement the plant understanding and within two weeks significant improvements were identified and demonstrated. The combination of the pilot operation and the plant based laboratory program was able to quickly demonstrate the improvements and test with equipment that is fully scaleable from pilot plant to full scale.IntroductionPanoramic Resources Limited is a Western Australian mining company formed in 2001 for the purpose of developing the Savannah Nickel Project in the East Kimberley region of Western Australia. Panoramic successfully commissioned the $65 million Savannah Project in late 2004. The process plant at Savannah comprises a single stage crusher, SAG mill, flotation, thickening and filtering stages to produce a bulk nickel, copper, cobalt concentrate. Metallurgical recoveries average 86-89% for nickel, 94-97% for copper and 89-92% for cobalt. The plant was originally designed for a throughput of 750,000 tonnes per annum, but has consistently outperformed the design specifications.Due to low nickel prices the Savannah Nickel mine and processing plant were placed into care and maintenance in May 2016. Prior to suspending production Glencore Technology was engaged to investigate options to improve the concentrate grade. With the discovery of Savannah North in 2014 and the Savannah North Scoping Study demonstrating LoM ~8 years and Mining Inventory of 6.07Mt @ 1.26% Ni, 0.64% Cu and 0.09% Co significant future potential exists. By completing pilot plant studies prior to shutting down, the plant engineering studies can be completed and the plant readied for restart by the time the nickel price improves."

Jan 1, 2017

By Arsenio Enriquez, Adrian Deneys

"Rio Tinto through its subsidiary Kennecott Utah Copper Corporation (KUC) and Praxair have implemented the CoJet® gas injection system for copper anode refining. The system provides the capability to melt on average 60 to 70 tons of scrap copper per heat (with acceptable NOx emissions). The system has demonstrated the potential for tuyere-less sulfur and oxygen removal using coherent jet technology.This paper describes the process concept, system development, laboratory testing, implementation, current operation and ongoing developments."

Jan 1, 2009

By P Lever, D Hainsworth, H Gurgenci

The ACARP Landmark initiative has created the opportunity to advance the level of automation in the coal industry by first focusing on the core production area of longwall mining. A Landmark Longwall Automation project was commenced in July 2001. The major outcome of automation using on-face observation has been divided into ten outcome areas that have been fully scoped for a three-year initial project life. A major facilitating technology has been the implementation inertial navigation system (INS) technology that can map the shearer position in 3D. A focus of the project is to deliver a system that is at least as productive as the current most productive manually controlled longwall face.

Jan 1, 2002

By R. J. R. Cornelissen

The elimination of the incidence of silicosis in employees in industries such as mining and pottery is an ongoing international initiative. After many decades of industrial activity in these industries and many dollars spent on preventative measures, silicosis is still occurring. The exposure-prevention measures taken so far have certainly improved the working environment dust concentrations; however, the illness is still regularly diagnosed in workers. More funding is needed for interventions to improve working conditions. Many aspects of dust prevention and suppression will be researched and exposure assessment methodologies and equipment will need to be reviewed for the purposes of improvements in effectiveness. This paper presents results from laboratory tests carried out on gravimetric sampling pumps and cyclones. It highlights the erratic flow produced by gravimetric pumps of three different manufacturers who claim their respective pumps are equipped with flow stabilisers. The standard BS EN 1232:1997 is used as a basis for the tests. A method, albeit impractical for fieldwork, is shown for the elimination of the pulsation in the flow. This method serves to prove the method and protocol used in this study. The pressure loss caused air-flow resistance of cyclones is measured. The air inlet aperture size of cyclones is measured. The large discrepancy in the two criteria between individual cyclones is shown. The paper concludes that all the pumps tested failed the prescribed limits of BS EN 1232:1997 regarding the pulsation of the gravimetric sampling flow. The difference in flow characteristics of the cyclones, together with the erratic flow produced by the pumps, throws into question the accuracy of the exposure assessments. It is suggested that substantial resources be channelled towards solving these flow problems in parallel with measures taken to reduce exposure. In principle, the accurate assessment of exposure and dust concentration levels is a prerequisite for effective management of the problem of silicosis.

Jan 1, 2009

By A. E. Anderson, H. J. Hilll

Laboratory data for 155 field muds and 77 .shales have been used to develop correlations to estimate the net streaming potential component of the SP. Analysis of these data and comparison with field tests show that streaming potential corrections must be made to obtain an accurate estimate of the electrochemical potential for use in the determinntion of formation water resi-iiviy. The self-potential curve is related to formation water resistivity, and considerable effort within the oil industry has been directed toward clarifying this relationship. The Schlumbergers and Leonardon1,2 recognized that two types of potentials, electrochemical and electro-kinetic, resulted in the net potential variation in the borehole. Most of the later papers have dealt with the electrochemical component and its controlling parameters. The investigations of Wyllie,2" Salisch' and Moore5 provide the most extensive sources of data on streaming potentials across mud cakes. These authors observed streaming potentials of sufficient magnitude to be of critical importance in SP interpretation, if it is assumed that streaming potentials develop only opposite permeable beds. Streaming potentials across shales have been reported by Schenck and by Gondouin, et al.7 Since SP magnitude is the difference in potential opposite shale and sand beds, these authors suggested that the net streaming potential component may be negligible. The present investigation was initiated to evaluate empirically some of the parameters controlling the magnitude of the net borehole streaming potential and to determine whether useful relations between mud properties and net streaming potential could be established. Field muds were used in this investigation. These muds were characterized by the amount and type of chemical treatment utilized for five days before Sampling. Filter loss, mud resistivity, mud density and filtrate resistivity were determined for each mud with conventional methods and apparatus. Mud filtrate pH was estimated with Hydrion pH paper for the appropriate range. Streaming PotentIals Across MuD Cakes Commercial calomel-saturated KC1 electrodes are subject to potential changes attributed to contamination of the very small fiber-tip bridge by particles of clay from the drilling mud.3 To minimize this difficulty, a large diameter bridge (Fig. 1) was constructed with saturated KC1-agar gel and a filter disc of microporous porcelain. Experiments showed that streaming potentials across this bridge are less than 0.2 mv at pressure dif-

By S. Ngidi

Palabora Mining Company operates a low grade underground copper mine situated in the Limpopo Province, South Africa. Full production was first reached in May 2005 after a successful transition from an open pit operation to an underground block cave operation. The operation faces a number of technical and operational challenges, not the least being fragmentation of a competent rock mass and external dilution. The cave is subdivided into three main sectors being the east, the west and the central sectors. Caving was initiated from the weaker central sector, which has the majority of its drawpoints located directly under the open pit bottom currently filled with about 130 million tons of waste material from the pit wall failure incurred in 2004. About 48% of the ore reserve has to be extracted from the western sector, which has a much courser fragmentation compared to the other two sectors and only 25% from the central sector with the finest fragmentation. The main constraint during the ramp-up stage has been secondary breaking of drawpoint blockages. Ground-breaking secondary breaking and cave management initiatives and practices have made it possible for Palabora to realize and sustain high production rates.

Jan 1, 2007

From a vast army of workers to gargantuan machines to immense volumes of material being moved, almost everything about the Port of Miami Tunnel (POMT) project points to tunneling on a massive scale. Almost.The star of this underground and underwater show is a Herrenknecht tunnel boring machine (TBM,) nicknamed ?Harriet? by a local Girl Scout troop. With her 12.9-m- (42.3-ft-) diameter cutting head and a total length of 139 m (457 ft), Harriet is boring through thousands of cubic meters of clay, dirt and sand, which is often mixed with coral and other materials, to create two 1,280-m (4,200-ft) traf?c tunnels connecting Watson Island and the Port of Miami (Dodge Island) beneath Biscayne Bay, FL. But in the midst of all of the oversized equipment and machines, a strong contender for the best supporting nod goes to a relatively tiny machine: the Brokk 400. Bouygues Civil Works Florida crews are using the compact, remote-controlled and electric-powered machine to excavate five cross passages between the twin traffic tunnels. The pas-sages will be essential to the safety of people who drive their vehicles under the bay every day.

Sep 1, 2013

By Yoshinori Iwasaki, Shosei Serata, Yutaka Mochida

A new comprehensive insitu instrumentation technique named this RCC Method has been developed for rapid assessment and improvement of the structural stability of underground openings. When applied to tunnel construction, the degree of present and prospective safety of underground openings can be determined in quantitative terms within 10 to 20 minutes of microcreep observation. When applied to mining, roofs and floors can be stabilized by controlling the stress conditions. This stress control method has eliminated the need for intensive roof bolting and extensive floor renewal in all cases where it was applied. Use of this technique is illustrated by field examples from the Seikan Undersea Tunnel of Japan and deep potash mining in Canada. NEW INSTRUMENTATION TECHNIQUE: THE RCC METHOD Failure problems in underground excavation usually arise in weak non-elastic grounds where conventional rock mechanics theories of elasticity are not only useless but also misleading. Presently, discontinuity planes in the ground are being considered a factor in assessing these failure problems, and while this development is interesting academically, it is not of much use in actual excavation work, where it is nearly impossible to identify and quantize all existing planes of discontinuity. Even if such an extraordinary task could be accomplished at an underground excavation site, effective use of the data would be difficult and impractical for rapid excavation work, with the possible exception of rare cases of ideally elastic ground.

Jan 1, 1976

By R. F. Favreau, Patrice Favreau

"A blast with explosives creates vibration waves in the zone around the blast.The prediction of the intensity of vibrations is important because people in the cinity demand that the vibrations do not disturb them, and society imposes limits on the vibrations. The U. S. Bureau of Mines (USBM) showed that the easurement of the particle velocity U predicts the risk of damage from vibrations. A currentapproach of blasters to monitor vibrations is to measure them with a seismograph at several distances S, and create a graph of U vs. S and the explosive charge “W” according to the equation U = K / (S / W)N where K and N are constants that depend on the blast method and the nature of the ground over the distance S. Though useful, this equation is empirical, and the results predicted from it are very variable, as shown by figure 1 which indicates that a prediction of U can deviate significantly from the actual value. Moreover, a minimum of two seismograph measurements at two values of S are required to establish the curve. However, here now exists another very convenient method to predict U; it is with the simulator Vibmas, which is based on the fundamental principles of how a blast reates vibrations. This simulator takes into account not only W but rather all the blast parameters, the type of explosive and the properties of the rock. Moreover, to establish the calculation of U as a function of S, only one seismograph measurement is required rather than two as for the USBM method. This last difference is important because it makes it easy to predict U not only as a function of S, but also as a function of the orientation of S. On the site this allows much safer control of the vibrations, and the use of larger explosive charges which reduce excavation costs. The article presents results from a field case at a hydroelectric project in Canada, where the deviation was very moderate. Use of this vibration simulator on the Web is very easy."

Jan 1, 2015

By A. R. T. Denues

"INTRODUCTION The orienting phases of the current investigation of cushioned blasting in the Explosives Division of the Bureau of Mines were indicated in a previous publication (5) 3/. Pertinent literature reviewed therein indicated a highly controversial field. This emphasized the need for experimental studies of many factors that affect the health and safety of miners and the efficiency of mining operations. Results of some orienting tests showed marked effects on practical hazards. Further, they emphasized the necessity and importance of the contemplated investigation. The scope and general plan of these practical inquiries into the safety of cushioned blasting were indicated.This investigation of cushioned blasting relates to the various means employed to reduce the intensity of application of energy from explosive actions in boreholes. It has been suggested (from p. 19 of reference 5) that the divisions of this work would correspond to the salient hazards affected by cushioned blasting. These include the ignition hazard, hazards from poisonous gases, and other practical hazards in the blasting technique. The ignition hazard was resolved into two components of approximately equal weight. These include studies of effects upon (1) the incendivity of blown-out shots and upon (2) the occurrence of such shots. Experimental studies of effects on the incendivity of blown-out shots were first undertaken. Questions of the best procedure for making these evaluations have been adduced, and the interpretation and utilization of the results of gallery testing seemed to require detailed attention; some preliminary general considerations of such testing were therefore necessary."

Jan 1, 1943

By John Wilson

"The unconformity beneath 75 per cent or over 6000 km2 of the Athabasca Basin in Alberta lies within economically exploitable depths. The basement beneath this unconformity consists of an extension of the Wylie Lake Pluton, locally faulted and containing areas of mylonitic rocks. While the rocks of the Wylie Lake Pluton are not promising host rocks for uranium ore deposits, the areas of mylonites, graphitic rocks and possible remnants of granitegneiss would bear closer examination. One area of maficmylonites shows a weathering zone enriched in Si, Ca, Na, Pb, Ni, Ba, Co, Sr, Zn and U in addition to reported values of 0.08 oz/ton gold. This zone occurs beneath 800 m to 900 m of Athabasca Group sediments, but similar rock types are present beneath much thinner cover elsewhere. Detailed geophysical exploration is required over the area of thinner Athabasca Group rocks to define more precisely the areas of promising basement rock type.IntroductionThe Athabasca Basin in Alberta has considerable economic potential which has not yet been realized. The geological setting is closely analogous to parts of the basin in Saskatchewan which host major uranium deposits. Recent advances in geophysical techniques have led to deposits being located in Saskatchewan below 600 m of cover. This means that the unconformity between the Athabasca Group and the basement lies at exploitable depths over 6000 km2 or 75 per cent of the Alberta portion of the basin. Much of this area was only cursorily examined almost a decade ago. In addition, Alberta's new Metallic Mineral Regulations have clarified the regulatory situation in the area, and opened up much land for exploration. This article is based on Wilson's (1985a) study of the Athabasca Group and Wilson's (1986) work on the basement and alteration beneath the Athabasca Group in Alberta."

Jan 1, 1987

By S. Y. Tan

The thermal stability of fully silicided NiSi with arsenic doping on silicon was investigated. The aims of the work were to investigate the Ni silicide phase-related issues associated with arsenic dopant and thermal annealing on Ni-FUSI/HfO2/Si and Ni-FUSI/HfSiO/Si gate stacks. It was found that arsenic-incorporation demonstrated some improvement in both morphology and phase stability of nickel silicided films at high processing temperatures regardless underlying gate dielectrics. The correlations of Ni-Si phase transformation and arsenic doapnt with their electrical and physical changes were established by sheet resistance measurements, X-ray diffraction (XRD), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS) analysis. Furthermore, the modulation of the work function (WF) of Ni fully silicided gates by arsenic impurity is presented, comparing the effects of dopant (As) on the WF and silicide phases (NiSi and NiSi2). It confirmed that the work function of NiSi can be tuned by implanting arsenic dopant, but it ineffective for NiSi2 phase.

Jan 1, 2010

By Bain J. H

Since zinc was first deposited at Risdon in February, 1917, provision of the most economical cathode assembly has been a subject of extensive research, the major problems being corrosion and efficient use of power.From the corrosion viewpoint, a perfect cathode is one in which the life of the headbar and the deposition sheet are the same. However, corrosion usually concentrates in a narrow zone across the face- of the sheet, resulting in breakages which, before the advent of argon arc welding, meant a loss of a 'complete assembly.Attempts to extend sheet life included use of thicker sheets, multitudinous protective coatings applied with varying degrees of success, re-rolling, and for a time, aluminium consumption was reduced when broken sheets found re-use as protecting strips. This latter economy became impracticable when electrode spacing was reduced for greater efficiency in power utilization.As an integral part of the electrode, the headbar was modified accordingly. Copper headbars, although more corrosion resistant, were replaced by aluminium due to a possibility of dissolved, copper promoting deterioration.Thicker electrodes and regulated spacing reduced internal shorting, whilst provision of knife-edge type supports on both contact and insulator ends of headbars aided in electrode centralising and continuous electrical conduction.After much experimeIitation, an assembly has been evolved which, with the aid of argon arc welding and tbe use of minimum additional aluminium, permits comparable headbar and sheet lives, combined with good electrical conduction throughout the life of the cathode.INTRODUCTION Over 300 tons of zinc are produced daily at Risdon from a purified zinc sulphate solution by electrolysis, the zinc being deposited upon all-aluminium (except for copper contact) cathodes. It is stripped in 72-hour cycles from the cathodes, melted and cast into the customary rectangular slabs.

Jan 1, 1958

By Bernard Lewis

This report summarizes fundamental research and technical studies conducted by the Explosives and Physical Sciences Division of the Bureau of Mines from July 1, 1949, to June 30, 1950. It is the fourteenth of a series of annual reports whose aim has been to bring to the reader a résumé of the research results that have appeared in published form during each fiscal year under the authorship of members of the staff. These are referred to throughout the report.

Jan 1, 1951

By D. J. Zuliani

A mass and energy balance for a modern electric arc furnace ("EAF") indicates that about 70% of the process energy losses are contained in the off-gas as chemical energy in the form of uncombusted CO and H2 and as thermal energy. Given the magnitude of the off-gas energy losses, improved EAF energy efficiency needs to focus first on controlling furnace practice to maximize "in-EAF" energy utilization and second, on recovering residual energy in the off-gas existing in the fume system. This paper focuses on the application of off-gas analyzers, sensors and process models to control and optimize "in-EAF" energy utilization efficiency. The paper will also discuss the application of heat recovery technology to EAF steelmaking.

Jan 1, 2015