Search Documents

By C. F. Lucks, W. D. Wood, H. W. Deem

Electrical ad thermal-conductivity measurements have been made on titanium and 6 titanium alloys. The following expression was derived for calculating thermal conductivity from electrical conductivity: K = 0.626 s T x 10-8 + 0.00497 where K = thermal conductivity, cal sec-1 cm-2 cm0C-1 s = electrical conductivity, ohm-]cm-1 T = temperature, deg Kelvin This expression gives calculated thermal conductivities that are not in error by more than 10 pct from the experimental values for A-55 titanium and the 6 alloys measured; namely, A-110AT, C-110M, C-130AM, Ti-6A1-4V, Ti-140A, and Ti-155A, which are representative of the presently available commercial a and a-ß titanium alloys. THERMAL conduction in a gas, liquid, or amorphous solid is accomplished by energy diffusion from molecule to molecule, a relatively slow process. For this reason, such materials have a low thermal conductivity. When a material is crystalline, there is in addition a heat transfer by a vibratory motion of the crystal lattice. It is the contribution of this lattice conduction that makes a crystal a much better conductor than a gas, liquid, or amorphous solid. Lattice conduction, however, does not account for the relatively enormous thermal conductivity of a metal. This is explained by the freedom of movement of valence electrons. These valence electrons drift in a metal in a direction toward a drop in electrical potential and, to a lesser degree, in the direction of a temperature drop in the metal. Since both the electrical and thermal conductivities of a metal depend upon the presence of free electrons, there should be some relatively simple relation between the two. Wiedemann and Franz in 1653 first discovered an approximate empirical relation between the electrical and thermal conductivities of metals at the same temperature. This ratio varies appreciably with temperature, and Lorenz later showed that by adding a temperature factor to the Wiedemann-Franz ratio the value of K/(s T) is constant, where K is the thermal conductivity, a the electrical conductivity, and T the absolute temperature. This Lorenz constant shows a greater variation for alloys than it does for pure metals, the ratio increasing slightly as the proportion of alloying elements increases. It has been found that a closer correlation between electrical conductivity and thermal conductivity can be obtained by means of an equation of the form K - A s T + B [1] where A and B are constants. In this equation the term AsT is the contribution of electronic conduction and B is the contribution of lattice conduction to the total thermal conductivity. EXPERIMENTAL MEASUREMENTS Electrical-resistivity and thermal-conductivity measurements on titanium and 6 titanium alloys serve as the basis for determining an equation of the K = AsT + B type for titanium alloys. Specimens—Table I shows nominal compositions of the 7 metals on which electrical and thermal conductivities were measured. The electrical and thermal-conductivity specimens for each alloy were taken from stock of the same heat and usually from adjacent sections of the same bar. All of the metals measured were in a mill-annealed condition. Methods—Electrical-resistivity measurements

Jan 1, 1959

By A. J. Terrones

THE classical papers on contact metasomatic deposits by Lindgren on the Clifton-Morenci district,' by Barrell on Marysville, Mont.,' and by Gold-schmitt on the Oslo district, Norway,' laid the foundation for understanding of the importance of separating the metamorphic process from the subsequent metasomatic stage. Knopf' made a big step forward by recognizing that sulfide ore minerals are invariably younger than silicates and by further stressing the importance of structural control" in ore finding. Some years later Harrison Schmitt" fought the idea that contact metasomatic deposits are erratic, irregular, bunchy, economically marginal, and of small size, concluding that these descriptions have little factual basis. He emphasized the importance of detail mapping and careful geological study as fundamental requirements for a better understanding of these deposits. This article presents a comparative description of the structural features at the Magistral, Antamina, Morococha, Vilca, Ferrobamba, Katanga (Quibio), Tintaya, and Huarca contact deposits (Fig. 1). Further, it will describe how these structural features controlled the emplacement of the intrusives, their shape, distribution of metamorphic and metasomatic halos, and sulfide deposition in post-skarn structural channelways. Finally, the modifications introduced by a superimposed hydrothermal stage recognized at some localities will be discussed. Primary exploration and careful sampling of recognized structural targets were instrumental in outlining the copper ore potential at the Antamina and Tintaya districts, thus proving the benefits and reward of careful geological examinations in this type of deposit. The Magistral District: This district lies in the Province of Pallasca, Department of Ancash, in northern Peru, at 8o 16' S and 77" 47' W. High to medium grade copper orebodies in garnetite, bordering a quartz monzonite stock, are exposed at the bottom of a glaciated valley in the western slope of the Andes at 4250 m (14,000 ft)* elevation.

Jan 1, 1959

By Michael I. Brittan, Craig M. Sams

"Economies of scale and the variable characteristics of many large ore deposits have resulted in grinding installations using very large SAG mills fitted with variable speed drives. Low-aspectratio single-stage SAG mills were introduced in South Africa to process the consistent gold bearing Witwatersrand quartzites. Elsewhere, circuits were patterned after the more conventional North American circuits with high-aspect-ratio SAG mills followed by ball mills. This paper provides information on two recent Gold Fields group installations covering both types of SAG mill in large, single-stage applications. While these operations process similar tonnages, the mills represent opposite ends of the aspect-ratio spectrum. The Tarkwa mine in Ghana employs a low-aspect 27’ x 42’ 14MW SAG mill. The St Ives mine in Australia operates a conventional 36’ x 18’ 13.4MW SAG mill.INTRODUCTIONGold Fields is one of the world’s largest gold producers with annual production of approximately 4.2 million ounces. The Gold Fields group has operations in South Africa, Ghana and Australia, along with numerous exploration sites and advanced projects in several other countries. This paper discusses new milling operations in Ghana and Australia.TarkwaThe Tarkwa Gold Mine is located in Ghana, West Africa, approximately 350 kilometers west of the capital city of Accra (Figures 1 and 2). The site conditions are tropical with an average annual rainfall of 1,930 mm and a maximum temperature of around 35°C."

Jan 1, 2006

By K. V. S. Sastry, K. D. Lofftus

Mathematical modeling and computer simulation are two valuable quantitative tools that are being effectively applied to mineral process- systems. This paper presents an up-to-date assessment of process modeling and simulation, identifies a number of associated challenges and opportunities and discusses in detail sane of the aspects of applying the current state-the art modeling and computational tools.

Jan 1, 1989

By Masayuki Ishikawa

In a radio frequency and optoelectoronic device packaging, Gold-Tin (Au-20 wt% Sn eutectic) solder is used widely due to the excellent electrical and thermal conductivity, high strength, and negligible creep characteristic under repetitive thermal cycling. With the recent lead-free movement, Gold-Tin solder is recognized as an alternative material for high temperature Lead-Tin solder. Generally, Gold-Tin solder is supplied in the forms such as ribbons, pellets, and ring frames. However, these forms must be set-up accurately on the joint area to press chips in bonding, therefore, it is difficult for these forms to satisfy the recent requirements for the down sizing in the connection areas. On the other hand, Au-20 wt% Sn solder paste can be applied flexibly to various supplying methods, such as printing, dispensing system and pin transcript. These methods also make it possible to reduce the production cost. However, in the case of using the solder paste, the void issue is one of the most undesirable problems. The void causes the degradation of the characteristics such as the bond strength, electrical characteristic and thermal conductivity. We have been intensifying the development of the void free paste, and have achieved void reduction by optimizing the powder size, the flux composition and the reflow condition.

Oct 1, 2003

By Aparup Chattopadhyay, Barun K. Gorain

"Porphyry copper deposits are the most important source of copper and also gold within the orogenic belts. These deposits are characterized by low grade copper ore (0.2% to 1% copper) and host precious metals like gold, silver and platinum. A characterization tool has been developed for complex porphyry type copper-gold deposits with an aim to quantify copper and precious metal deportment. This quantification is a challenging task due to low grades and also due to the presence of both visible and invisible precious metal content in different sulphide and non-sulphide phases. Studies were initiated on various complex ore deposits and also on samples representing various processing streams such as flotation and leach products. This paper presents the development of a systematic approach to diagnostic metallurgy using state-of-the-art optical and automated mineralogy, micro-probe, dynamic SIMS and TOF-SIMS analysis for quantification of invisible and visible precious metals content in various species. The relevance of this characterization to metallurgy will also be briefly discussed in this paper.INTRODUCTIONA novel characterization tool has been developed for double refractory gold ores and complex copper-gold ores using state-of-the-art technology for quantitative gold and copper deportment study. The characterization of these ores is a challenging task due to low copper and gold grades in ores, presence of both primary and secondary copper sulphide phases and variable proportion of visible and invisible gold in different sulphides phases (pyrite, chalcopyrite, chalcocite and bornite) and iron oxide phases (magnetite, hematite and goethite). A study was initiated on various ore deposits and also on samples representing various processing streams of pilot plant batches such as flotation concentrates and tailings. This paper attempts to discuss the deportment characterization methodology through presenting results from investigations on four samples from a flotation circuit viz, Feed, Final concentrate, Cleaner Scavenger Tail and Rougher Tail samples. These four samples represent the key streams for a typical copper-gold flotation flow sheet. The key objective of this investigation was to identify and quantify visible and invisible gold along with understanding the morphology and liberation of gold associated with various sulphides, Fe- Oxides and non-sulphide gangue species. In addition, the aim of this study was also to relate this mineralogical and gold deportment information to metallurgical performance."

Jan 1, 2013

By Bjørn Nilsen, Werner Stefanussen

The construction of the Guaigui Multipurpose Project includes a 74 metre high concrete face rock fill dam, a 350 metre long diversion tunnel and a 350 metre long spillway tunnel. The topography in the project area is very steep, and the rock masses are characterized as soft rocks. The stability of the 80 to 100 metre high dam abutments and the excavation of the tunnels in soft rock conditions have caused various challenges and problems to be solved. Limited pre-investigations have called to a great extent for estimation of parameters for the stability calculations based on experience. The preliminary calculation of the stability of the planned rock slope above the spillway intake platform has been carried out by conventional partial factor methods and by use of a computed based Slide Program. The two methods of calculation give different results , and that rock support is necessary to obtain an acceptable factor of safety for a slope inclination of 52o. The input parameters for the rock mass characteristics need to be verified for the permanent calculations.

Jan 1, 2006

By Joel Darmstadter

The position of the coal industry in America’s fuel and power picture remains one of prime importance. Measured in Btu terms, the industry is the country’s leading energy producer and an important exporter. Foreign coal sales yield annual proceeds of about $4 billion. Coal’s one-fifth share of the nation’s energy consumption is nearly as high as that of natural gas. Coal is the electric utility sector’s principal fuel supplier. It accounts for about55% of the electricity generated at power stations.

Jan 1, 1999

By J. McCreedy

"The addition of Portland cement to hydraulic sand fill has resulted in the production of stable and self-supporting cemented sand fill. The use of cemented fill in the mines of The International Nickel Company has resulted in substantial economies in timber requirements, de-creased dilution of ore and greater flexibility in mining methods.Coupled with special mining techniques, it has permit-ted mining by both cut-and-fill and shrinkage stoping methods to much greater depths than heretofore. The use of cemented sand fill has permitted revisions to undercut-and-fill mining which have significantly improved the efficiency of this method.Automated mixing systems have been developed for preparing cemented sand fill in surface sand plants on a continuous throughput basis. Control of cement-sand mixtures is obtained by the use of a mass flow measuring system and weighing cement feeders."

Jan 1, 1966

By Lutz Markworth, Evren Ören

"The worldwide demand of ores and the depletion of the high-purity deposits make it necessary to recover ores in increasingly finer size fractions in the feed material. The flotation technology of more than 40 years old plants was not able to recover the ultra fine material. Those slurry tailings ponds now have the chance to be re-processed with PNEUFLOT® technology.The bubble sizes of different flotation technologies have a huge influence of the results especially regarding the recovery of the ultra fine particle sizes.PNEUFLOT® technology of HUMBOLDT WEDAG Coal & Minerals Technology GmbH in Germany was applied to ultra fine Phosphate, Copper and Platinum ores. The results will be presented in this paper.Conventional technology like agitator flotation has its limits in the flotation of fines due to turbulences in the cell. The position of the agitator influences the recovery of the fines. A deep impeller generates a higher froth zone. This helps to catch the medium fines. Due to the static head of the slurry inside the cell, compressed air is required for such cell designs.Column flotation is well known for a good selectivity without having in the first cell a good recovery. This leads to invest in several cleaning stages to reach an acceptable recovery. Further more, compressed air is required to generate the air bubbles to the flotation process, which are much bigger than with PNEUFLOT® technology applied.INTRODUCTIONHigh metal prices are actually the basis to invest in poor deposits or deposits with very fine intergrown ores which have to be milled down to ultra fine powders less than 60 micron. The liberation grade has to be determined by a mineralogical analysis. Polish sections have to be prepared and interpreted by using of a microscope. Figure 1 and figure 2 are showing polish sections of a platinum-nickel ore from Petchenga Nickel at Zapolyarni Mine in Russia. The head grades for rich ore are for copper between 0.05 – 0.15%, for nickel between 3 – 7% and for platinum group minerals approx. 0.15 oz/t. With an efficient flotation technology it can be upgraded to 20 oz/t."

Jan 1, 2009

By Irving Hartmann

The Experimental Coal Mine of the Bureau of Mines has served principally as a valuable and unique testing laboratory for studies of the explosibility of coal dust and mine gas; studies of the numerous complex and interrelated chemical and physical factors that govern the ignition of coal dust and the propagation of mine explosions; and studies designed to develop measures for preventing explosions or reducing their destructive effects. These researches, coupled with educational efforts by the Bureau of Mines and enlightened safety consciousness in the mining industry, had fruitful results. This is evidenced by the remarkable reduction in the frequency of major coal-mine explosions and the number of fatalities from explosions since the Bureau of Mines was established. Despite this progress, further important unresolved problems arise; these are due in part to changes in mining conditions and methods, which have brought about increased production of fine coal dust in highly mechanized operations. To solve the new problems, research must be continued without interruption. The results of many very recent and current studies in the Experimental Coal Mine are summarized briefly, and pertinent studies by European mine-safety-research organizations are listed.

Jan 1, 1957

By R. V. Norris

The great coal strike of 1902, which confined the work at the Short Mountain colliery of the Lykens Valley Coal Com pany almost exclusively to pumping, gave an opportunity to determine with considerable accuracy the cost of pumping the water from these very old, extensive and wet mines. This colliery, which is located in the extreme southwestern end of the anthracite coal-field, has been operated continuously since 1836, and has shipped 7,747,313 tons of coal. This and the Williamstown colliery are the only operations in Dauphin county. The workings cover about 5 miles along the North dip of the extreme westerly end of the basin, with the operating slopes near the center. They extend around the westerly spoon of the basin and back about 31/4 miles easterly on the South dip. The mines are very deep, the present workings ex tending to 711 ft. below sea-level, and about 1600 ft. below the lowest surface-opening. The coal is hoisted principally from the Short Mountain slope, which is 1550 ft. long, with 26 to 68 degrees dip, and from an inside slope, No. 4, 800 ft. long, with 52 to 72 degrees dip. The ordinary capacity of the colliery is about 1000 tons per day, and the average output for the years 1897 to 1901, in clusive, was 297,000 tons per year. The seams worked are the lowest Red Ash measures, being, respectively, Nos. I, II and III of the coal-bed series, but locally called the " Little Lykens," " Lykens," and " Whites." On the accompanying plan the Lykens seam is shown in full and the Whites in dotted lines. The pumping-plant is divided into four lifts, the pumps being located as shown in the section, Fig. 1, and the plan, Fig. 2.

Jan 1, 1904

Several industrial-scale HydroFloat separators have recently been installed at Mosaic?s South Fort Meade beneficiation plant for the purpose of improving phosphate recovery and throughput capacity. This technology was implemented after numerous laboratory, bench-scale and on-site, pilot-scale test campaigns. The results from this detailed test work provided sufficient justification for the complete retrofit of the existing coarse and ultra-coarse flotation cells. Data indicate that the metallurgical results obtained with the full-scale separators are consistent with that obtained during both the bench- and pilot-scale evaluations. The benefits, theory of operation and commissioning of the equipment are also discussed.

Jan 1, 2007

By N. Aslin, G. Heferen, H. DeWaal

"Mount Isa Mines (MIM) acquired a reputation for the successful application of R&D to develop break-through technologies for the mining industry starting in the 1978’s through until the early 2000’s. The ISAPROCESSTM tank-house technology has been licensed to copper refineries throughout the world, and a significant per cent of the world’s copper is refined using this technology. Since development in the late 1980’s more than 20 ISASMELTTM copper and lead smelting furnaces are now installed in countries around the world. Jameson Cell flotation technology developed jointly by Mount Isa Mines and Professor Graeme Jameson is widely used in the Australian coal mining industry and increasingly in the base-metal and gold industry. The IsaMillTM’s developed at Mount Isa and McArthur River made it possible to develop the McArthur River and George Fisher orebodies and has been successfully implemented into base metal fine grinding applications around the world. The most recent commercialised innovation is the atmospheric leach Albion ProcessTM with its supersonic HyperSpargeTM gas sparger, is being adopted as a solution to the increasing complexity of orebodies. MIM’s contribution to the industry was significant given the size and the remote location of its operations with Townsville Copper Refineries more than 1350 km and Mount Isa 1800 km from the nearest state capital of Brisbane. This paper will briefly discuss the development of each of these technologies and why MIM – now owned by Glencore - was so successful innovating and developing such technologies over a period of nearly 40 years.INTRODUCTION Mount Isa is located in the Gulf Country region of Queensland about 1800 kilometers North West of Brisbane (see Figure 1). It came into existence because of the world class mineral deposits found in the area. In 1923 the orebody containing lead, zinc and silver was discovered by the miner John Campbell Miles. Mount Isa Mines Limited (MIM) was founded in 1924 to develop the minerals discovered by Miles, but production did not begin until May 1931. It paid its first dividend in 1947 after 16 years of troubled production. In 1954 the 1100 copper orebody was discovered and with rapidly rising reserves during the 1950’s and 1960’s led to the construction of new concentrators to treat lead/zinc/silver ores in 1966 (#2 concentrator) and copper ore’s in 1973 (#4 concentrator). The difficult nature of the Mount Isa lead-zinc orebodies has meant that the company had always needed to be at the forefront of mining technology. In the 1970’s through to the 1990’s, it became a world leader in developing new mining techniques and processing technologies as a response to declining metal prices and rising costs. Mount Isa has been smelting copper since 1953 and lead since the early 1930’s. Copper Refining at Mount Isa’s fully owned subsidiary of Copper Refineries Proprietary Limited (CRL) had commenced operations in 1959."

Jan 1, 2018

By G. W. Grove, O. V. SIMPSON

During the years 1945, 1946 , 1947 , and up to July 1, 1948, only one death was caused by mine fires in bituminous - coal mines of the United States . The one fatality occurred in an Illinois mine in December 1945, and , therefore, there had been a period of 2-1/2 years in which no deaths occurred as the result of mine fires . Moreover, 1946 was the first year since 1930 in which no deaths occurred from mine fires . This record is markedly better than that of 1944 , when 89 fatalities and great property damage were caused by mine fires in bituminous - coal mines and 16 additional men were killed by an explosion that occurred while they were attempting to seal a mine fire .

Apr 1, 1949

By W. C. Maurer

A study of the mechanics of shear failure of rock under pressure has been made. The transition from brittle to ductile failure occurs when the friction along the fracture surfaces exceeds the shear strength of the rock. A machine has been developed for measuring both the shear strength of rock and the friction along rock fracture surfaces. In this shear machine, the fractures are forced along definite planes; as a result, the rock is stronger than in compression tests where the fractures choose the weakest paths through the specimens. Friction is composed of several forces: (1) the forces to slide irregulurities on surfaces over each other; (2) forces to shear some of these irregularities; (3) molecular attractions across the fractures; and (4) forces required to break bonds resulting from melting and welding at the tips of irregularities on the surfaces. Friction along rock fracture surfaces is not proportional to contact pressure as usually assumed; instead, it increases as the contact pressure raised to the 0.4 to 0.8 power. INTRODUCTION It is difficult to produce tensile stresses under the high compressive stresses present in the earth; therefore, in deep drilling and geological faulting, shear failure predominates. This shear failure mechanism is complicated because rock is a heterogeneous material containing pore spaces, microfractures, elastic discontinuities and other imperfections. A study of shear failure of rock under pressure has been made to obtain a better understanding of this complex mechanism. A machine has been developed and used to measure the shear strength of rock and friction along sheared surfaces. This machine has certain advantages over the compression test — shear properties can be measured under low normal stresses and shear stress and normal stress can be varied independently. The first part of this paper is a description of shear failure of rock under pressure. The role of shear strength and friction along fracture surfaces in the shear failure mechanism will be discussed. The second part consists of a description of the shear machine and a discussion of the shear strength and friction data obtained using this machine. It will be shown that shear strength depends upon the size of the stressed zone, and that friction does not increase linearly with contact pressure as usually assumed. Attempts are made to relate some of the new concepts to tectonic failure and to dril ling. SHEAR FAILURE IN ROCK TRIAXIAL TESTS The shear failure mechanism is illustrated by the triaxial test shown in Fig. 1. In this test, a cylindrical rock specimen is subjected to a confining pressure, PC, and an axial pressure, pa. These external pressures produce normal a and shear T stresses on inclined planes within the specimen equal to1 where 0 is the angle between the specimen axis and a normal to the inclined plane. Fig. 2 shows how triaxial specimens deform as the axial pressure is increased. The pressure is

Jan 1, 1966

By Rodolfo Espinosa

"Industrias Peñoles, S.A. de C.V. in Mexico, has nine mining operations, six managed by Peñoles (base metal mines) and three managed by Fresnillo plc (precious metal mines). Seven of the operations use flotation and the other two are heap leach operations, one for gold and the other one for copper.This paper gives a brief introduction of Peñoles, shows mine locations and describes the main process characteristics of each concentrator. It also presents four of the new operating practices that were implemented over the last four years to improve the economics of the mining operations. These include (1) the use of centrifugal gravity concentrators to increase the recovery of gravity recoverable gold (GRG) and silver (GRS), (2) the use of expert systems to reduce process variability while increasing grades and recoveries, (3) the application of the Six Sigma methodology to key projects to ensure success and personnel development and (4) the use of water chemistry fundamentals to identify chemistry problems and design adequate solutions for improving grades and recoveries.INTRODUCTIONPeñoles was founded in 1887. It is a mining group with integrated smelting, refining and chemicals producing operations. Peñoles is the world largest producer of refined silver and metallic bismuth, the leading Latin American producer of refined gold and lead. It is amongst the world leading producers of refined zinc and sodium sulfate.Peñoles operates and controls six underground mines in Mexico and is the largest producer of zinc and lead of the country. It also produces copper concentrates and cathodes. Through its 77.1% equity stake in Fresnillo plc (a London Stock Exchange listed company); Peñoles is also a significant producer of gold and silver. Fresnillo plc operates three precious metal mines in Mexico. While Fresnillo is the world largest primary silver mine, Ciénega and Herradura are two leading gold mines of Mexico. Figure 1 shows a map of Mexico indicating the locations of the Peñoles mines. The main process characteristics of each concentrator are listed in Table 1."

Jan 1, 2011

By A. M. McKim, J. S. Ambler

"The iron ore of the Scully Mine is upgraded from 36 per cent Fe to 66 per cent Fe through single-stage crushing, wet autogenous milling, sizing by vibrating screens and two-stage spiral separation, followed by a process in which the concentrate is dried and then further improved by high-tension separators. The capacity of the concentrator is 17,000 long tons of concentrate per day. Discussion of the operation will recognize the special problems encountered in handling preponderantly fine ore, relate issues of interest regarding wear and review mechanical innovations found to be advantageous at Wabush. The modern trend toward big equipment, thoroughly instrumented, has been the theme of design. Effects on availability must be a consideration in this choice, and sectionalizing of circuits to minimize these consequences is as important as streamlined maintenance."

Jan 1, 1969

ONE DAY IN the mid-1880s, in a suburb 0f Pittsburgh, Pennsylvania, there dismounted from a train the two foremost leaders of the day in the coal and steel industries-Andrew Carnegie and H. C. Frick. Their attention was drawn to a well-loaded car of coke, which their experienced eyes recognized as a superior product. "I'll bet you that coke is from the H. C. Frick Coke Company," Mr. Frick challenged. "I'll bet it was shipped by my company." In a spirit of fun Mr. Carnegie accepted the wager. Mr. Frick lost the bet: the coke had come from M0rewood, one of three sites being operated under the direction of a young entrepreneur, Erskine Ramsay. If Mr. Frick's confidence was somewhat dented by this occurrence, the responsibility was his own. He himself had opened the way for Erskine Ramsay to become the youngest of mine superintendents; and he had dispersed all dissension regarding his choice with the words : "I'm not interested in his years, I'm interested in his record. He makes more coke in an oven than any other superintendent. And I'll take 'em out 0f the cradle if they can make coke... Suppose he is only twenty years old? ... The d --- kid is a genius, I tell you." Erskine Ramsay was to follow in the tradition of Carnegie and Frick. Not only was he ambitious and a worker his background had prepared him for it. Coal mining was in the Ramsay blood. His father, Robert Ramsay, of whom the son once stated that he had no superior as coal mining and mechanical engineer in this country, once accounted in these words for the phenomenal accomplishments which had attached to the name "It does no harm to belong to a family of mining engineers who are just as good as any in America-if it is myself that says it." Anyone acquainted with Robert Ramsay's character realized that he was not given to overstatement. And the above-mentioned Mr. Carnegie encountered young Ramsay again, a few years later in his career, and wrote of him to young Erskine's father, that he was "going to be a credit `tae us a' " (a quotation from Robert Burns.) Nor have Mr. Ramsay's achievements been identified exclusively with the industrial field in which he early asserted himself. He has been an inventor whose techniques in mining engineering have received international recognition. As an investor of foresight, he has benefitted others immeasurably, as well as himself, being an influential factor in the upbuilding of several communities in his chosen and well-loved adopted home state of Alabama since 1887. He is a philanthropist whose benefactions have run into millions, the chief beneficiaries being educational and charitable institutions. Amidst his accomplishments the lighter side of life has not been neglected and he is known for his hospitality, his

Jan 1, 1953

Despite the current economic downturn that is now decimating iron ore production, Minnesota?s mining operators remain optimistic about the long-term prospects for the industry. Reflecting this optimism, the development of several new mining projects continues in the state. The future of mining in Minnesota was the featured topic at the combined 82nd Annual Minnesota Section of SME Meeting and 70th Annual University of Minnesota Mining Symposium. More than 500 mining industry professionals, including engineers, executives, mining managers and equipment suppliers from the around the world, attended the meeting, which was held April 14 and 15, 2009, in Duluth, MN. The combined meeting featured a keynote session with three distinguished speakers plus a panel discussion by representatives from several of Minnesota?s taconite producers. The keynote speakers were Curtis Clark, president and chief operating officer, Behr Dolbear, who gave a presentation on the ?State of the Mining Industry.? Phil Newman, chief operating officer, CRU Strategies, spoke about challenges facing the mining industry and James A. Skurla, acting director, Bureau of Business and Economic Research, Labovitz School of Business and Economics, University of Minnesota Duluth, discussed the importance of mining to northeastern Minnesota?s economy. The taconite producers panel discussion included Jonathan Holmes, vice president and operations manager, ArcelorMittal; Ed Latendresse, vice president and general manger, Hibbing Taconite; John Tuomi, vice president operations services, United Taconite and Mike Mliner, vice president and general manager, Northshore Mining. The mangers provided updates on their respective operation The meeting included concurrent technical papers sessions on mining, processing, environmental and nonferrous mining. The sessions included technical papers that provided information on the status of a number of new mining projects in the state. The conference also offered a SME short course titled ?The basics of iron mining.? A tradeshow that featured about 100 companies and organizations offering products and services to Minnesota?s mining industry ran in conjunction to the conference. It was estimated that more than 900 people, including conference registrants and special invited guests of the vendors, attended the tradeshow opening reception. This was the largest trade show in many years. The Minnesota Section of SME also held its annual business meeting during the conference.

Jan 1, 2009