Search Documents

By A T. Job, M L. Edgar, P R. McAree

Characterising ores in-pit and in real-time presents a significant value opportunity for the mining industry. Hyperspectral imaging systems are proposed as an enabling technology to achieve this real-time characterisation. This paper considers the application of a hyperspectral imaging spectrometer mounted on a shovel. We define the performance requirements for such a spectrometer and associated subsystems during a typical dig-load cycle. The relatively high swing rotation speed of the shovel requires approximately video-rate exposure times to achieve good spatial resolution. We analyse a selection of components against these requirements and find that suitable commercial spectrometers, detectors and optics appear fit-for-purpose. Automated, real-time spectral classification systems are also available, with only relatively modest requirements for processing power. The paper argues that at near peak solar illumination, a system for field deployment at the required sensitivity is viable using only commercial off-the-shelf components.CITATION:Job, A T, Edgar, M L and McAree, P R, 2017. Real-time shovel-mounted coal or ore sensing, in Proceedings Iron Ore 2017, pp 397–406 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By W. M. Armstrong

This paper compares research on development efforts in various countries, consideration being given to gross expenditures, manpower involved, source of funds, sector of performance and type of activity. The Canadian R & D activity is then reviewed, particularly as applied to the industrial sector, the problems of applied research in Canada are discussed and some remedies are suggested.

Jan 1, 1968

By Russel Delmar

Construction of Ontario Power Generation?s 12.8-m diameter, 10.4-km long water diversion tunnel in Niagara Falls, Ontario, is underway. The tunnel is being excavated by means of a 14.44-m diameter open gripper Tunnel Boring Machine. The tunnel lining is constructed as a two-pass system with the initial lining consisting of rock bolts, mesh, steel channels or ribs, and shotcrete, and the final lining consisting of pre-stressed cast-in-place concrete with a waterproof membrane. This paper describes salient design and construction aspects as follows: ? Regional and Site Geology ? Tunnel Layout and Design ? TBM Tunnelling and Cast-in-place Concrete Lining Construction

Jan 1, 2008

By R. Schulz, K. King

Concentrating Line 6 just went down again. The control room operator checks the graphic display. Only one piece of equipment shows an alarm. Clicking on the ball mill icon, he discovers the culprit was the low flow lube switch. The flow looks okay now, but it is the third time this week the switch has stopped the line. Maintenance is called, the switch replaced and the line is up running again. Sending the right person to the right spot immediately can save hundreds of hours of downtime every year. This paper discusses the principles behind implementing smart First-Out Fault Detection to dramatically reduce equipment downtime in new, or existing control system architectures. Methodologies are presented to maximize the system benefits, while minimizing development costs. Case histories are presented for a number of successful implementations in mineral processing plants.

Jan 1, 2001

By T. B. Linde

The Morenci In-pit Crusher and Conveyor System has been designed with safe production and cost savings in mind. Large open pit mines around the world have been installing semi-mobile crushers and linking them with a pit conveyor system to lower unit cost. At Morenci two 60/89 in. gyratory crushers are incorporated into the semi-mobile crushing plants. The ore is reduced to -8 in. and transported out of the mine on a 60 in. steel cable belt. This paper includes an overview of the Morenci In-pit Crusher and Conveyor System from the drawing board to open pit installation and finally a discussion on operating and repair considerations.

Jan 1, 1990

By Mikael Ramström, Mark Board, Clayr Alexander, Wes Johnson

"The Coeur d’Alene mining district in northern Idaho was first discovered more than 130 years ago and has been the most prolific silver producer in the United States. The Lucky Friday Mine of Hecla Mining Co. (Fig. 1) is the oldest (76 years) and deepest mine in the district, producing approximately 725 t/day (800 stpd) from narrow, vertical lead-zinc-silver veins. Cut-and-fill stoping is currently employed at depths to about 2.3 km (7,500 ft) below ground surface, making it one of the three deepest mines in the western hemisphere. The #4 Shaft, a winze collared at approximately 1.8 km (5,900 ft) below surface and extending to a depth of nearly 2.9 km (9,600 ft), was recently completed to exploit the high-grade 30 Vein, whose resource has been identified to at least 3 km (9,700 ft) in depth.As with other deep mines worldwide, a number of challenging engineering issues occur, including: high in situ rock stress, squeezing ground, seismicity, high in situ rock temperature that requires refrigeration, diesel equipment that generates diesel particulate matter (DPM) requiring high ventilation airflow rates and long travel times for worker transport to mining areas.This article describes the methods that Hecla Mining Co. has employed during the past 50 years to combat these issues, with emphasis on the current efforts to implement continuous, mechanical mining with automated or teleremote operation and to introduce electric and battery-powered equipment to minimize refrigeration and ventilation requirements for the removal of DPMs.Geology and in situ stressThe host rock mass is an extremely thick sedimentary sequence (the Belt Series) that has been tilted vertically by mountain building. The rock mass in the current section of the mine consists of weak, heavily foliated argillites and stronger, bedded silty-argillites termed siltite. The vertical veins (80° to 85° dip) are parallel to the foliation with an approximate width of around 3 m (10 ft). There are two regional, vertical faults that parallel the vein; one forming the hangingwall of the orebody and one approximately 90 m (300 ft) in the footwall. Additionally, there are several thin, rough northdipping faults that occur in the footwall of the vein which terminate on the major vertical faults.Both the argillite and vein package rock have moderate strength, with uniaxial compressive strength averaging about 100 MPa (14,700 psi with a range from about 70 to 125 MPa), and are moderately abrasive, with CERCHAR abrasivity index of 2 to 3. The major in situ stress is horizontal and oriented in a northwest direction with magnitude about 1.5 times the vertical stress. Consequently, the Lucky Friday stress magnitude at depth is analogous to significantly deeper South African gold operations."

Jan 12, 2017

By V. Maseko, C. Musingwini

"When considered collectively, Mineral Resources and Mineral Reserves are arguably a key asset for any mining company. Mineral Reserves are the economically mineable portions of Mineral Resources. They therefore provide a good indication of the economic prospects in the short to medium term and associated non-financial impairments for mining companies, hence a focus on Mineral Reserves. An assessment of modifying factors for converting Mineral Resources to Mineral Reserves revealed that Mineral Reserves were most sensitive to long-term commodity prices, hence the focus on long-term commodity prices. The justification for selecting gold and platinum mines is that they collectively make a significant contribution to South Africa’s earnings from mining.The introduction of the South African Code for the Reporting of Exploration Results, Mineral Resources and Mineral Reserves (SAMREC Code) in 2000 informed the basis for analysing long-term commodity price assumptions for major South African gold and platinum mining companies between 2000 and 2016. The analysis revealed that the least number of non-financial impairments occurred when long-term commodity prices were within ±5% of spot prices. This finding suggests that this range is the ideal range for long-term commodity price assumptions to improve confidence in Mineral Reserve declarations and minimize impairments. Introduction The South African Code for the Reporting of Exploration Results, Mineral Resources and Mineral Reserves (SAMREC Code) defines a Mineral Resource as ‘a concentration or occurrence of solid material of economic interest in or on the Earth’s crust in such form, grade or quality and quantity that there are reasonable prospects for eventual economic extraction’ (SAMREC, 2016, p. 18). Mineral Resources are categorized according to increasing levels of geoscientific confidence or knowledge, from Inferred to Indicated and lastly, Measured categories. The SAMREC Code defines a Mineral Reserve as ‘the economically mineable part of a Measured and/or Indicated Mineral Resource’ (SAMREC, 2016, p. 25). In some of the other reporting codes such as the Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (the JORC Code), a Mineral Reserve is synonymous with an Ore Reserve. The conversion of Mineral Resources to Mineral Reserves involves applying modifying factors, which are non-resource considerations. The modifying factors used in the Mineral Reserve estimation process include mining, metallurgical, processing, infrastructure, economic, marketing, legal, environmental, social, and governmental factors. Each of these modifying factors consists of several components which require due consideration in the estimation of Mineral Reserves. Table I shows some of the components typically considered for each of the modifying factors."

Mar 1, 2019

The range of environments which control the level of ground support required vary greatly in terms of rock type, rock structure and the mining method used. At the operating mines visited during this review the level of ground support was such that incidence of rock-fall- related accidents were rare. It was also found that methods existed to support most of the conditions encountered. The main problem areas were weak rock, major geological structures, areas of heavy jointing, high development density and areas affected by high mining-induced stresses and blasting. With stope support the level of success was much lower than that achieved in development; the larger spans and more rapid changes in geometry of open stopes compared with cut and fill stoping (where cables were originally used) led to significant problems. Before a useable design method for cable support of stope walls and pillars can be obtained the precise failure mode of the walls and pillars, and the interaction of the support and the rock mass must be investigated.

Jan 1, 1982

By Adrian Coombs, Paul Magowan, Derek Zoldy

Continued development and intensification are fuelling the urgent need for new trunk infrastructure within The Regional Municipality of York and throughout the Greater Toronto Area. Permitting of these projects is increasingly subject to public scrutiny to severely restrict dewatering through construction technologies and the requirement for a comprehensive and effective Environmental Management Plan. Three current projects: one on the York Durham Sewage System and two in the City of Toronto 1.Conventional Design, Tender, Award: 4,150m (13,600 ft.) 2.7m (9 ft.) finished interior diameter soft ground tunnel for York Region’s YDSS Interceptor Trunk Sewer 2.Negotiated Contract: 3,800m (12,500 ft.) 3.5m diameter (11.5 ft.) rock tunnels for Enwave’s environmentally sustainable and innovative chilled water system in downtown Toronto 3.Conventional Design, Tender, Award: 2,200m (7,200 ft.) 3.3m diameter (10.8 ft.) rock tunnel for reinforcement of Hydro One’s primary hydro feed in the downtown core of Toronto These projects exemplify issues such as: EPB tunnel and sealed shaft technologies Substantial permitting requirements associated with dewatering Mitigation of rock creep Congested downtown rights-of-way Deep shafts and confined working compounds Unique scheduling and cost benefits when Owner, Contractor and Consultant can work together cooperatively.

Jan 1, 2007

The smelting of the Broken Hill lead concentrates at the Broken Hill Asso,ciated Smelters produced, among other products, approximately 4,900 ounces of gold and 8,800,000 ounces of silver during the year ending June 30th, 1938. The following table shows the actual amounts of gold per ton of lead concentrate produced during this period at the important mines. The total gold in the period is calculated from the number of tons of lead concentrates produced, and by comparison with the production' of silver, shows thatthere is no constant relation between the amounts of gold and silver.The fact that no gold is seen during milling, even when gravity concentrating tables are employed, signifies that the gold does not occur as occasional coarse particles.Further, as the values increase considerably in the flotation slime, it can be inferred that the gold occurs as minute inclusions in one or more of the minerals in the lead concentrates.The four most abundant minerals in the lead concentrate are galena, zinc blende, chalcopyrite, and...

Jan 1, 1940

By F. Grant

"General *The mining experiences of the coal mining industry in Western Canada have been extremely varied, with the mining companies having to adjust their operations or fail due to the harsh economy of the country in the first part of the century. The bituminous or mountain mines had the railways as main consumers with, at times, optimism that potential steel producers would require metallurgical coal. The prairie and foothills mines mainly provided household fuels, with the fine coal sold to local thermal power plants at discounted prices. In practically all cases fuel competition was very keen, and the less successful mines ceased operations in short-time spans. Knowledge of the parameters that governed the success or failures of the past coal operations should be of value to the present and future mining companies. The initial coal mines were small and were started to supply local demand. These mines had little in the way of capital machinery, engineering, or transportation equipment; therefore the mining methods and mine plans were very simple. The first industrial-sized mines imported most of their management and mining methods from other mining areas, mainly Great Britain. It took time to change the bias of management and mining methods to the requirements of strata characteristics, with rapid closure to those mines that were slow to adapt working methods. The main markets for coal were for household fuel, thermal power plants and railways, with very few other industrial markets developed. The economy of the period was harsh and cyclic and the coal mines were affected more than most industries by these boom and bust periods. It led to the survival of the fittest or the most efficient. Due to the economy, mechanization was introduced to the mines very slowly, with the inability to sell coal fines at a profit being another reason for the delay. Manual labour with hand tools was the main means of production. The work was heavy and arduous, and the pay was based on contract coal tonnage; therefore both men and management paid close attention to details so that nonessential work could be eliminated. Mine openings were dimensioned so that coal could be loaded easily by hand and support requirements were kept to the minimum. Transporting and handling the timber supports required heavy labour; thus the most efficient dimensions were chosen to suit the strata. On the other hand, during the main production seasons the mines tried to make the strata stress work for them so that the pressure was kept on the coal face to keep the coal loose while the strata, a short distance back, was induced to cave to minimize the abutment stresses. This caused mining to be an art, using skills developed by experience with the strata. This led to the development of efficient mine layouts with the openings dimensioned to the strength of the strata and the type of support available. The lack of capital and mechanization, and the manual labour, induced the mines to correlate their service and haulage systems with their mining methods. This caused many innovations that proved very practical."

Jan 1, 1985

By G. S. Harper

Noise in general and drilling noise in particular have received increasing attention within the South African mining industry during the last 10?15 years. The Mine Health and Safety Committee1, during their 2003 annual summit, established two significant milestones to be met by December 2008 and December 2013. The 2008 milestone target is that of no more than ten per cent deterioration in hearing among occupationally exposed individuals, whereas the 2013 milestone target is that of less than 110 dB sound pressure levels at any place in the workplace. While these targets relate to general noise within the mining industry, it is widely believed that the most significant source of noise contributing to noise induced hearing loss (NIHL) among the underground workforce, is that of pneumatic rock drills. Data pertaining to the noise emission level of any machine is generally reported as either a sound pressure level or a sound power level of a single machine measured under free field conditions as defined in Appendix 3 of SABS-ISO 37442. However, rock drills are seldom used in isolation and underground conditions cannot be considered as free field. A methodology for the selection of rock drills on the basis of total operating cost has been developed. However, this paper focuses on the noise elements of the generic methodology and provides a model for the prediction of the composite sound pressure level and the equivalent noise exposure levels of groups of individuals from machines, used singly and in combination in an underground environment based on the sound pressure level determined according to SABS-ISO 3744 under free field conditions. The methodology includes provision for the consideration of the effect of hearing protection devices and the use of multiple machines in combination and provides an indication of the potential costs of hearing compensation.

Jan 1, 2006

By Jesús E. Gómez

Verification and production testing of soil nails requires debonding the upper section of the soil nail to isolate the portion of the soil nail intended for testing within a specific ground type. In pre-drilled soil nails, debonding can be accomplished relatively easily because the bar can be fitted with a debonding sheath before its installation. However, debonding of hollow core bar soil nails requires special procedures to achieve the intended result. This paper is a summary of the Federal Highway Administration (FHWA) Hollow Bar Soil Nail (HBSN) Test Program, which is described in detail in FHWA-CFL/TD-10-001. The program was developed to establish a suitable debonding procedure to test hollow core bars in soil nailing applications, and to initiate a database on typical bond values of HBSNs. The investigation showed that it is possible to debond hollow core bars for testing. It was also found that hollow core bars installed in granular soils may present ultimate bond values that are significantly higher than those typically used for design of conventional pre-drilled soil nails.

Jan 1, 2011

By J. Patterson

"Acid Mine Drainage (A.M.D.) formed from oxidation of disposed pyritic wastes presents a potential pollution hazard for Equity Silver Mines Limited and the mining industry in general. Failure to collect and treat these acidic effluents can eventually affect the quality of receiving streams and endanger aquatic life forms. Treatment and discharge of A.M.D. to the receiving environment must comply with stringent anti-pollution laws.Wastes mined at Equity Silver Mines Ltd. are predominantly acid generating and must be handled according to a materials management plan to minimize impact on the environment. Effluent collection and treatment facilities have been constructed to address the short term environmental concerns with reclamation and research programs being developed to address and monitor abatement measures for control over the long term.The purpose of this paper will be to offer a brief overview of these measures. Key topics for discussion will be: kinetics of Acid Mine Drainage, acid generating potential, water treatment and sludge handling, special wastes, waste dump construction, waste rock amendments, bacteriocide research, simulations, and reclamation measures. Programs designed to evaluate impact on the receiving environment, although they form an extensive part of the program, will not be discussed in this paper.INTRODUCTIONEquity Silver Mines Limited is located in the Central Interior of British Columbia, within the Omineca Division, 35 kilometers southeast of Houston Mining and approximately 575 kilometers by air north-northeast ofVancouver (Figure 1).The deposit consists of three economic mineralized zones: The Southern Tail, Main and Waterline Zones. Mining of the Southern Tail commenced in April, 1980 and was completed in the first quarter of 1984. Main Zone production was initiated during the last quarter of 1983 and the Waterline Zone remains undeveloped to-date. Remaining reserves are in the order of four years contingent on favourable metal prices. The three deposits (Figure 2) occur within a window of interbedded volcanic and minor sedimentary rocks. The older volcanic sequence is bounded on the west by a small granite-like stock and on the east by a gabbro-monzonite complex. All are overlain by a series of younger lava flows."

Jan 1, 1988

By Mandius C. Lundal

This report describes the work done to develop a coal mining machine to increase productivity and recovery from thin seams beyond the highwall, in addition to decreasing the miner's susceptibility to to highwall hazards. First, radar transducers were adapted to measure coal thinkness and detect rock and coal interfaces; Then, the radar was incorporated into a cutterhead with steering controls. Next, visual displays were designed to show cutter position in the coal seam, and anticipated change In coal seam inclination. Finally, development of a telemetry system made remote control of the cutterhead possible. Simultaneously, a high-performance extended depth (HPxD) auger machine was designed with an automatic system to handle 600 ft of 36-in. diameter dual spiral flight conveyor sections. A two man crew controls all operations from a weather conditioned cab outside the VDZ, either at night or day time. As a primary mining tool, working 4000 hr/yr (2 shifts/day) recovering 60% of the coal 600 ft beyond the highwall, production to 500,000 ton/yr can be achieved. Volume II contains technical discussion of subsystems and machine drawings.

Jan 1, 1977

By K Niiranen

Luossavaara-Kiirunavaara AB (LKAB) operates one iron ore mine, three concentration plants and three pelletising plants in Kiruna, Sweden. The current methods of separation at the beneficiation plants are low intensity magnetic separation (LIMS) and reverse apatite flotation, where the wet LIMS stage is regarded as the crucial part of silica separation from the ore. Because future silica levels are expected to increase in the incoming material to the beneficiation plants, geometallurgy has become an important area of development and research.A laboratory-scale methodology was developed for the systematic characterisation of the ore for mineral processing, with the focus on the high silica ore type B2 and newly discovered subtypes. This methodology combines mineralogical, geochemical and process mineralogical characteristics. Automated mineralogy (QEMSCAN®) is used to study the modal mineralogy, the distribution of silicate minerals in different particle size classes after comminution, the deportment of silicon (Si) between various silicates and the degree of liberation and intergrowth of magnetite and silicates. An essential stage in the systematic characterisation of the ore deposit for mineral processing is the estimation and simulation of different parameters from the laboratory scale to the full scale at the concentration plants. This is achieved by using empirical models based on the data collected at the mineral processing plants. As the first step to implement the geometallurgical information, the current geological model is reconstructed with the mineralogy and the two, newly defined subtypes of high silica ore type B2 are separated into different domains.To study the reduction of the SiO2 content in the magnetite concentrate, a large-scale reverse cationic silicate flotation laboratory test program was initiated in early spring 2016. This program investigated potential silicate flotation in the beneficiation plants at the Kiirunavaara site. The second target is to implant mineral processing parameters into the block model based on the new geological model. This information provides a good basis for making a prognosis for mine planning and a quality prognosis regarding the crude ore for mineral processing.CITATION:Niiranen, K, 2017. A geometallurgical perspective on a high-grade iron ore deposit at Kiirunavaara, northern Sweden, in Proceedings Iron Ore 2017, pp 309–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

As we look back through the Proceedings of our Institute, we find few papers dealing directly with education and recruitment. Apart from papers prepared in the earlier decades of this century, there was little written discussion on the subject until the 1950s, and mostly this was by the professionals, the professors and lecturers who staff the various mining schools of Australia and New Zealand.I use the term "mining school" in its fullest and widest meaning, to cover all aspects from ore to metal, and not in the narrow meaning that the word might imply. At the same time, in restricting the parameters of this address to "ore to metal" I recognize that I am excluding the very important fields of physical metallurgy and materials science; this I do because there is a limit to the quantum of any paper, and in fact these subjects are more closely allied to the use rather than the production of metals.However, the lack of education papers does not mean that education has been regarded lightly by The Institute. Sir Maurice Mawby in his presidential address in 1968, reminded us of the original objectives of The Institute, one 'of which was, "To promote the arts and sciences connected with the economical production of the useful minerals and metals ...". Our present Royal Charter is more specific when it says that one of the objects of The Institute is, ". . . to encourage the study of engineering with special reference to mining and metallurgy ...". If we recognize that in itself membership of our Institute is one means of continuing our education, it is true that education has been a concern of The Institute since it was first founded.Occasionally in recent years, an intrepid president has ventured to tell the academics what the industry needs, and he generally does this in a "no-question" situation! However it is encouraging that those entrusted with mineral education have always accepted this; they keep coming back for more and ask us to tell them what we want, and they will provide it.In 1948 a considerable dialogue on education was initiated when a standing committee was established by the Council of The Institute. In the period 1949 to 1951, three papers were prepared under the chair...

Jan 1, 1974

By VIVEK KUMAR HIMANSHU, M. P. Roy, P. K. Singh, A. K. Mishra, RAVI SHANKAR

Blasting with the aim to reduce oversize boulders in underground has many hurdles due to limited accessibilities and poor site conditions. Optimized drilling and blasting parameters can help to achieve this objective. The major challenges of the blast designers lie within deciding blast geometry, namely drill hole diameter, burden, and spacing. The general approaches covered worldwide to determine burden-spacing are based on various rules of thumb, which are based on previous experiences of blasts and the associated outcomes. However, many parameters influencing optimum burden-spacing to achieve desired fragment size are site specific. Sometimes drill geometry is decided based on associated blasting hazards rather than rock fragmentation. The Kuz–Ram model is a worldwide accepted rock fragmentation predictor. The parameters associated with this predictor also include burden-spacing for a blast. Back calculation of burden-spacing from the Kuz–Ram model can be used to achieve desired fragment size. This paper deals with burden-spacing determination by using an empirical approach for the underground stope ring blasting.

Jan 4, 2020

By W. H. Oppelt

Two exploratory gasification tests of limited duration were made at Dorsten, Germany, with strongly coking Pittsburgh-bed coal in a fixed-bed pressure gasifier. To reduce the coking potential of the Arkwright coal, ash refuse from the gasification of Dorsten (Leopold) coal was added to pre-pare coal-ash mixtures which contained nominal 20 and 30 percent ash. Major adjustments in principal process variables at the beginning of the tests resulted in wide fluctuations in the rate of gas production, gas offtake temperature, and carbon dioxide concentration in the gas. Because a higher steam-to-oxygen ratio was used in the tests than was customarily employed for routine operation, gas production was lower, and steam and oxygen consumption was higher. After operating conditions had been improved, the results of a 12~-hour-long test with addition of sufficient ash refuse to obtain a nominal 30 percent ash concentration indicated that operation is feasible with this coal mixture using a fixed-bed pressure gasifier equipped with a rotating coal distributor and stirrer.

Jan 1, 1966

By D. W. Cooper

The AMAX of Canada Limited Kitsault mine is located approximately 150 kilometers, by air, north of Prince Rupert, British Columbia at the head end of A1 ice Arm, just east of the southern tip of the Alaskan Panhandle. It is presently only accessible by sea or air, although a road is being constructed by the company which will provide access to Terrace, a commercial centre with a population of about 15,000. The topography is typically coastal mountainous with peaks rising to 2,100 meters around the head end of the inlet. The concentrator is at an elevation of 515 meters with the mine at 630 meters. This open pit molybdenum mine was previously operated between 1968 and 1972 by British Columbia Molybdenum Limited, a subsidiary of Kennecott Copper Corporation. AMAX of Canada Limited has spent $194 million to refurbish and expand this operation.

Jan 1, 1982