Search Documents

By William J. Krisko

This contract final report summarizes the design, fabrication and testing of a "line brattice air curtain" device under Bureau of Mines Contract H0357097. The purpose of this program was to develop the concept of using an air curtain for coursing ventilating air parallel with the air curtain From the last open crosscut to the face in exhausting ventilation systems to replace the line brattice cloth in room and pillar coal mining operations. The final design of the air curtain device consists of a 10-foot long closed end pipe with c: slot cut along its length. Pressurized air is delivered to the open end with a hydraulically-driven blower. A sheet of air emanates from the slot and is directed toward the mine roof. An invisible sheet of air is thus created between the top of the machine and mine roof and acts a an extension of the existing conventional line brattice.

Jan 1, 1977

By D. Nyungu

Despite observations of spalling and damage of mine excavation wall rock in the Bushveld Complex (BC) over the passage of time, there have been very few time-dependent or creep tests carried out in South Africa on rock, particularly on BC rock types. The research described in this paper deals with the investigation of stress and strain conditions influencing spalling of wall rock in BC mine excavations, and the influence of time on the tensile strength of several BC rock types. Time-dependent laboratory testing of BC rocks was carried out in indirect tension. The results show that the magnitude of the tensile strength of BC rock types is approximately 5% of their uniaxial compressive strength magnitudes. The average long-term uniaxial compressive strength of the BC rocks, interpreted from the axial stress-volumetric strain graphs, is 56% of the UCS value. The long-term tensile strength is shown to be less than 70% of the normal tensile strength. Extension strains at tensile strength failure ranged between 0.16 and 0.21 millistrain. Values corresponding with the long-term tensile strength are less than 70% of this range, namely, 0.11 to 0.15 millistrain. These results represent new knowledge, since such rock testing and analysis does not appear to have been carried out previously on BC rock types. Elastic numerical modelling was carried out to illustrate the extents of tensile stress zones and extension zones around of typical BC mine excavations. The models showed that large zones of extension strain can occur around BC excavations, and that the magnitudes of the extension strain can substantially exceed the critical values determined from the laboratory testing. The implication of this is that there are substantial zones surrounding BC mine excavations that will be prone to time-dependent spalling conditions and perhaps more significant failure.

Jan 1, 2014

The mineralogy, textures, and genetic significance of a silver-rich siderite vein and an apparently co-genetic galena vein from the South mine, Broken Hill are discussed.Both veins cut sharply across the Main Lode Horizon and appear to be coeval with thc A.B.H. Consols lode.The minerals of thc siderite vein apparently result from the preferential leaching of silver from Main Lode Horizon ore with a demonstrable "breakdown series" commencing with tetrahedrite, passing through silver sulpho-salts, and ending with simple binary compounds or with elemental silver.The siderite vein has been deposited by metahydrothermal fluids along the lines of Schneiderhohn's "secondary hydrothermal" mineralization.

Jan 1, 1968

By Raphaël Mermillod-Blondin, Claude Bazin

"Sampling is an important step for ore body evaluation and daily plant material balances. The Gy’s equation is regularly used to assess the size of the samples to be collected and to estimate the reproducibility of the collected samples. The equation works well for iron and base metal ores but seems to produce pessimistic estimates of the gold content reproducibility for gold ores. A model is proposed to simulate the division of samples using a standard splitter and discrepancies are observed between the Gy’s equation predictions and simulated samples reproducibility for crushed gold ore. Results of the simulation show that sampling a pile of ore crushed to -2 mm should lead to more reproducible gold content than it is observed in practice and predicted by the Gy’s equation.INTRODUCTION With current gold prices above $1400 per troy ounce operators seek for new economical ore bodies. The metallurgical evaluation of an ore body is one of the numerous steps required to justify the investment for the development of a gold mine. Metallurgical testing requires to sample the ore body and to prepare the ore sample for the grinding and separation tests. The preparation implies crushing the ore usually to less than 2mm and its division into batches of a given weight for subsequent processing. For gold ore testing a batch of crushed ore is ground in a laboratory mill and leached using cyanide. Gold recovered in the solution is used as an indicator of the ore processing amenability. One difficulty associated with ore testing is due to the reproducibility of gold content measurements of the feed sample. According to the Gy’s equation (Gy, 1979; Morisson, 2009) the division of a 20 kg batch of -2 mm ore containing 5 g/t of gold into batches of 1 kg may lead to batches containing 5 ± 5 g/t of gold. For this reason the gold content of a feed sample is usually back calculated from the assays of the solution and solids residues of the leaching process. However, these two assays may contain measurement errors that can propagate through the calculation of the gold recovery. The use of the feed assays as a redundant information could add robustness in the evaluation of ore amenability to processing. This paper discusses the problem of sampling reproducibility for a gold ore. The analysis is carried out with reference to the Gy’s equation for the sampling of particular materials."

Jan 1, 2012

By John C. Nigro

This Bureau of Mines report summarizes the performance characteristics of a 30-day around-the-clock gasification-pelletizing test conducted in October and November of 1980 with North Dakota Indianhead lignite. Gasification was conducted in a commercial-size, 6.5-it-diam, Single-stage, fixed-bed, atmospheric pressure producer with a rated capacity of about 30 million Btu/hr. Iron oxide pellets made from a commercial hematite concentrate were fired with the low-Btu gas in a 2.8-ft-diam by 35-ft-long pilot plant rotary kiln at a rate of 900 lb of pellets per hour. Gasifier operations at fuel feed rates up to 3 tons of lignite per hour and hematite pellet induration with raw 160-Btu/std ft3 lignite gas are described.

Jan 1, 1982

Your assessment of the minerals business. I would first like to express our profound sadness and sincere condolences to the families of the miners who lost their lives in recent mine mishaps particularly in West Virginia, and other locations. Any loss is unacceptable. It is time to review and, if required, re-establish a rigorous health and safety agenda in the mines. It must involve a review of health and safety regulations. And innovative training methods for sensing, awareness and mitigation of health and safety hazards must be developed. As far as the minerals business is concerned, I am excited about the outlook for mining. Over the last 20 years, global demand for minerals has closely mirrored the growth of the gross domestic product. Minerals re-main a major part of the world’s economic foundation. And that will continue to be the case. It is no surprise that the fortunes of the mining industry rise and fall with general economic trends. Globally, mining has been strong — thanks to the explosive economic growth in Asia. The U.S. mining industry has performed reasonably well, with notable strength in the metals, coal and construction and aggregate areas and with some softness in the industrial minerals sector.

Jan 1, 2006

By Joshua Hoffman, William Chad Wedding, Braden Lusk

The emergence of electronic detonators as viable products for use in production mine blasting has enabled mining professionals to rethink the traditional blast design methodologies that pertain to timing. In many ways, electronic detonators can allow great advances in productivity, cost effectiveness, fragmentation, and safety. There are a number of commercially available systems that enable users to program delay times, usually in one-millisecond intervals, according to design decisions. While manufacturers have performed internal studies pertaining to the accuracy of these systems, an independent study quantifying the accuracy of the systems has not been completed to date. The mining industry is in the business of production and any quality control endeavors to independently confirm the accuracy studies performed by the manufacturers would only detract from their bottom lines. Furthermore, limited information is available concerning the accuracy of modern pyrotechnic delay based detonators. In 1985, the Bureau of mines completed a study of three manufacturers’ electric millisecond delay detonators (Bajpayee, 1985). This was the most recent extensive independent study performed on detonators, which unitized pyrotechnic delays, from numerous manufacturers. Advances in the manufacturing process for pyrotechnic delays may have increased the accuracy of detonators using these technologies in recent years. It is commonly accepted that electronic detonators are more accurate than both shock tube type non-electric as well as electric detonators, but the relative accuracy was not objectively and adequately quantified.

Jan 1, 2011

By Bruce D. Hansen

For many years, Newmont has focused on improving its operations. After the merger between Newmont and Santa Fe Pacific Gold, Newmont created synergies of more than $50 million a year in Nevada. This was done primarily through optimal ore movements and consolidation of various functions. During the current period of low gold and copper prices, Newmont has refocused its efforts on efficient operations worldwide. At its mine facilities in Nevada, Newmont has used a combination of several strategies to decrease the costs of operations and to increase profitability. These include computer technology, optimal use of infrastructures, procurement strategies, functional consolidation, enhanced mine planning and several available metallurgical processing options.

Jan 1, 1999

By A. Lane

The socio economic risks of mining in South Africa have been emerging for some time now, and have been brought into sharp relief by recent events in the platinum sector. The slow pace of social upliftment in the country has lead to widespread social unrest with consequent calls for different forms of resource nationalism. Fundamentally, the key stakeholders are not fully aligned, and are not engaging productively. This poses significant above-the-ground risk to mining companies. Measuring social impact, deploying inclusive solutions and engaging effectively with stakeholders are three ways in which mining companies can mitigate this risk.

Jan 1, 2013

By A J. Scogings, W J. Shaw

The successful development of industrial minerals projects requires an integrated, holistic understanding of the metallurgical and product performance test work in the context of the geological setting of the deposit and applied to mining, processing and marketing of saleable products. The product specifications provide the essential starting point for geometallurgical studies. A sound understanding of the desired product is needed to design and interpret a program of test work. Examples are provided from recent studies on bentonite and graphite deposits.For bentonite projects, the naïve testing of only the cation exchange capacity (CEC) as a measure of purity can lead to unexpected outcomes when the deposit is mined. The CEC attribute may remain the same, while other important properties such as pH and swelling index change markedly with depth, due to weathering and oxidation, leading to disappointing production outcomes.For graphite projects it is not enough to report only total graphitic carbon content (TGC). Knowledge is required of the in situ flake size and textures in addition to purity and flake size distribution of extracted graphite, which may all vary from one domain to another across the deposit. Such geometallurgical attributes of the ore will impact on the ‘basket price’ used to estimate the value of marketable parcels of expected product.Disclosure of such information must be considered part of fully informing the market. As with all new project developments, consideration of the JORC (2012) and VALMIN (2015) Codes requires disclosure of all material information. This includes the geometallurgical characterisation, ie those aspects of the mineralogy that impact on resource evaluation, ore reserve definition and project valuation.CITATION:Shaw, W J and Scogings, A J, 2017. The importance of geometallurgical test work for industrial minerals projects, in Proceedings Tenth International Mining Geology Conference 2017, pp 83–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By M. A. Trevits, J. E. Urosek, A. C. Smith, M. P. Valoski

The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), is conducting research to test, evaluate, improve or modify coal mine fire-fighting strategies and methodologies through large-scale tests. Since wood is the second most abundant fuel available during a coal mine fire, it was decided that series of large-scale wood crib fire tests were needed to measure the products of combustion and to observe the capability of commonly available direct application fire suppression equipment, namely, fire extinguishers, water and gas-enhanced foam. This paper discusses the wood crib fire tests, provides insight into the products of combustion and describes observations made during the application of the fire suppression agents.

By Jonathan Duncan, Tim Burgess, William Kendall, Jens Lange

"Steel wire mesh is the accepted standard for roof and rib skin control at most coal mines in the United States. Wire mesh is delivered to the mine in bundles that are heavy and awkward to handle. The large size, stiffness, and weight of the wire mesh can present a safety hazard in transporting underground and storing on the roof bolter. Installing wire mesh on the roof and ribs with the roof bolter can be a challenge as well.Synthetic mesh is lighter than wire mesh and can be folded and rolled into a safe, manageable size. A single synthetic mesh roll large enough to cover the roof and ribs in a deep cut can be safely handled by two men. The roof bolter is designed to carry and dispense the roll as it advances and installs primary roof support, resulting in a single pass roof and rib ground control solution. This paper focuses on the design and implementation of the roof bolter synthetic mesh handling system developed by J. H. Fletcher & Co., Huesker, Inc., and Oxbow Mining.INTRODUCTIONRoof and rib skin control in some coal mines has been an issue since mining first began. Roof and rib skin problems vary from mine to mine. The type of roof rock material exposed after mining; the mine atmosphere; and stresses from depth of cover, over mining, and/or undermining are some of the variables that can contribute to roof skin problems from mine to mine.Potential roof and rib skin problems can be time dependent as well. Some mines have roof skin rock, sometimes called draw rock, that falls when drilling the hole for the roof bolt as the initial roof support is installed. Some roof skins are more stable but can fail over time. The failure of roof skin can even be between properly installed roof bolts with roof plates (Figure 1).Mines have most commonly used a wire mesh that comes in individual panels anywhere from 5 ft x 5 ft (1.5 m x 1.5 m) all the way up to 5 ft x 16 ft (1.5 m x 4.9 m) in size. They are typically constructed of 8- or 9-gauge wire welded on a 4 in (102 mm) square pattern. A 5 ft x 16 ft (1.5 m x 4.9 m) panel weighs approximately 35 lbs (16 kg). These steel wire mesh panels can make it a difficult and sometimes dangerous task to deliver them from the surface to the roof bolter and then store on the machine. Manipulating the mesh panels from the storage area on the machine to the final installation position on the roof or rib can also be a daunting task (Figure 2)."

Jan 1, 2010

By Mark R. Pettitt

The charter of this investigation was to identify and promote the application of noise control technology to future longwall mining machinery. Intensive noise and vibration data were acquired on a typical longwall shearing machine, and the highest noise levels were shown to radiate from the cutter drums. Shearing machine cutter drum noise control techniques that take advantage of the nature of the dynamic forces generated during coal cutting were developed. These include both structural redesign and force isolation techniques. A reduced noise cutter drum was developed that achieved a 5 to 6 dBA system noise reduction at the operator's position. Its operational performance was verified by a six-month long in-mine test. It was evident from the data that additional noise reduction could be achieved by treatment of the shearing machine hydraulics. Noise control of secondary sources was also investigated. A method of reducing full or empty stage conveyor noise (and continuous miner conveyor noise) by 5 to 10 dBA was demonstrated through isolation techniques. Underground mine durability testing, however, is yet to be demonstrated.

Jan 1, 1986

By Stephen K. Pave1

Over 1,100 tons per day of Fluid Catalytic Cracking Unit (FCCU) catalyst is used worldwide. During the cracking reaction, catalyst is contaminated by deposited metals including nickel, vanadium, potassium, copper, iron, sodium, etc. To compensate for contaminants, a portion of the circulating catalyst inventory is withdrawn for disposal and fresh catalyst is added. The DEMETR process takes spent FCCU catalyst and removes a portion of the metal contaminants, enabling the refiner to recycle demetallized catalyst, thus reducing the solid waste from the refinery. Through August, 1993, the operation of one unit for one refiner has resulted in the recycling of over 7,500 tons of spent catalyst.

Jan 1, 1994

By Prasad S, Chatterjee S. S, Singh B. N

The chief source of metallic iron for steelmaking in India, even today, as it is in most part of the world, is through blast furnace (BF) route. This will continue to be so in the foreseeable future as the technology is most efficient, both process and economy-wise. However, as the world is moving into the next millennium, a critical look is being given to the process primarily because of its non-ecofriendliness (as a result of extensive use of metallurgical coal/coke requiring elaborate pollution control facilities) and huge investment involved for supporting facilities like extensive raw material preparation and handling, agglomeration, adoption of sophisticated instrumentation and control system, etc.

Jan 1, 1999

My selection of the Australian coal industry as the theme of this Presidential Address arose from the fact that it is one of our most important mineral industries. The industry is presently prospering.M.ore coal, mostly of better quality (except for certarn power-house types), is being produced more cheaply in terms of real money than at any time in the past, and exports overseas are currently at a highlevel.In. spite of this, concern has been expressed in certam quarters about the future of some phases of the industry; for example, there has been some public comment on the selling price of our coking coal to Japan, the possible over-export of our coking coals from New South Wales, the introduction of foreign capital to develop large-scale mining ventures in Queensland, and the proposed export of substantial quantities of coking coal from the same State.Furthermore, proposals for the introduction of atomic power plants into several States well endowed with reserves of coal have given rise to comment, and recently the Department of National Development(1968) warned that insufficient attention is being paid to "orderly development and careful husbanding of the nation's coal.To reach a balanced judgment on whether these views are well founded it is essential to make a broad survey of the present position of the coal industry in the Australian economy. I therefore propose to deal briefly with several aspects, and to comment, in particular, on the important subjects of exploration and research in progress at present on Australian coals.Detailed descriptions of the Australian coalfields are to be found in existing technical publications (e.g.. Andrew, 1965; McLeod, 1965) and the data on coal reserves have been progressively revised as more accurate information has become available. In New South Wales detailed knowledge of the coal reserVes is limited to under 20 per cent of the sur...

Jan 1, 1969

By P. Turcotte, E. Karampinos, F. Mercier-Langevin

In some underground hard-rock mines, squeezing compressive ground conditions are influenced by the presence of rock foliation and high stress. In these cases, the orientation of the foliation with respect to the drift direction has a considerable impact on the magnitude of the resulting deformation. Irrespective of the reinforcement and support strategy, keeping drives developed sub-parallel to the rock foliation operational is difficult, and often requires excessive rehabilitation during the lifetime of the excavation. This study uses field observations and convergence measurements at the LaRonde and Lapa mines of Agnico Eagle Mines Ltd to provide guidelines of the anticipated squeezing levels at these operations.

Jan 1, 2015

By G. H. McKay

AT the Eagle mine, near Gilman, Colorado, where the Empire Zinc Company have installed an underground mill, transportation problems were comparatively simple. A railway siding on the Denver and Rio Grande railway is equipped with an unloading dock or platform at the portal of their service incline adit to the mill. This 18-degree incline is approximately 600 feet long from the unloading track to the head of the mill skipway. For the Big Missouri mill, upwards of 2,500 tons of material and equipment had to be trucked from tidewater at Stewart, B.C., a distance of 21 miles to the Big Missouri camp at elevation 2,800. From that point, this freight had to be moved either over or through the Big Missouri ridge, rising to elevation 3,450, to its final location 800 feet from the surface between elevations 2,150 and 2,350. Immediately after leaving the government dock at Stewart, the road crosses the International boundary line into Hyder, Alaska, and then follows a water grade for eleven miles along the lower stretches of the Salmon river. leaving the river, the road climbs for two miles before crossing back into British Columbia territory at Silver Heights, and then continues for another mile and a half to where the Big Missouri road branches off from the main road to the Premier mine. For a distance of four miles from the junction of the roads, the Missouri road is very narrow, with many sharp curves and with irregular up and down pitches and grades up to 25 per cent until it reaches the Summit. From there on, a fairly easy grade leads a mile and a half to the end of the road on Joker Plats. In winter, the last stretch of road is subject to heavy snow drifting, especially through a narrow funnel-shaped gulch, known as 'The Gap', where the snow may pile up to a depth of over twenty feet.

Jan 1, 1938

By G. R. Luster

In most current practice, the methods that are employed in technical evaluations of cement raw materials are deterministic; i.e., decisions among alternative raw mixes and alternative plant designs are reached with the aid of only "average" compositions and "representative" samples of the available raw materials. Nevertheless, cement plants are sensitive to raw-material variability, and uniformly high-quality raw materials are not so abundant as they once were. Some simple examples will illustrate how geological techniques can be combined with geostatistical and operations-research approaches to customize mining and processing systems to deal with variable raw-material compositions.

Jan 1, 1987

By J. W. Givens, P. B. Crawford

A potentiometric model study has been made of the effect of vertical fractures existing in the matrix of the reservoir on the flooding or cycling performance. Fractures can have unusual flow characteristics. Fluid entering one side of a fracture can emerge on either the same or opposite side of the fracture, depending on the particular streamline. Fracture orientation has a great influence on the sweep efficiency. However, sustained fluid injection may still permit large areas to be swept. INTRODUCTION One can find considerable information available in the literature on the effect of fractures originating at the wellbore on sweep efficiencies of water-flooding or gas cycling programs.1-5 However, there arc few, if any, quantitative data reported in the literature on the effect of vertical or horizontal fractures existing out in the reservoir matrix on secondary recovery performance. Several papers have been presented on the effect of vertical and horizontal fractures on the productivity or conductivity of waterflood and gas injection patterns, but in all cases the fractures initiated at the well and simulated commercial fractures.6,7 It is believed that natural fractures may exist out in the reservoir matrix and would effect the displacement performance. The purpose of this report was to study the effect of a few isolated vertical fractures existing out in the reservoir matrix on the performance of waterflood or gas injection patterns. DESCRIPTION AND EQUIPMENT Since the potentiometric model was described by Lee8 it has been widely used to study numerous types of fluid displacement problems. The potentio- metric model can be used for fluid displacement studies when the following assumptions are valid: (a) steady-state conditions exist; (b) the mobilicy ratio is one; and (c) the capillary and gravitational effects can be neglected. Five-spot and direct line drive square patterns were studied using a copper strip of the desired length and orientation to simulate a vertical fracture in the reservoir matrix. The 20 x 20-in. model was considered to represent only one element of an infinite array of similar patterns. DISCUSSION AND RESULTS FIVE-SPOT PATTERN — ONE FRACTURE BETWEEN INJECTION AND PRODUCING WELLS Fig. 1 shows a quadrant of a five-spot pattem with the vertical fracture existing out in the matrix along a line connecting the injection and producing wells. Length of the fracture was equal to 35.4 per cent of the distance between injection and producing wells. In this particular pattern it is noted that fluid breaks through from the injection well to the producing well when the dimensionless time is equivalent to 26.9. Dimensionless time is defined as volume of fluid injected divided by the volume of displaceable fluid in the pattem expressed as a per cent. The cross-hatched areas of this

Jan 1, 1967