Search Documents

By W. E. Stiles

A method is presented for predicting the performance of water flooding operations in depleted, or nearly depleted, petroleum reservoirs. The method makes use of permeability variations and the vertical distribution of productive capacity. From these two parameters can be calculated the produced water cut versus the oil recovery. Derivations of the mathematical analogy is shown and sample calculations and curves of prediction are presented. Comparison is made of the predicted and actual performance of a typical 5-spot in an Illinois water flood. INTRODUCTION The use of water as a flooding medium in both depleted and "flush" oil reservoirs is gaining greater recognition and acceptance. Many of the shallower fields, depleted by primary production, have been and are being subjected to water injection in order to obtain some part of the large volume of oil remaining after primary production. Some of the earlier water flood installation proved highly discouraging and the value of water flooding was often questioned. Many of these earlier floods were haphazardly selected and developed as little was known of the physical characteristics and contents of the producing formations. The prior evaluation of the flood performance was impossible. During the past decade the development of the required reservoir engineering tools-—core analysis, reservoir fluid analysis, electric logs, fluid flow formulae, etc.—has allowed the engineer to construct and apply the methods which are presently being used to evaluate the economic and mechanical susceptibility of a reservoir to flooding. This discussion will present a method for taking into account the effect of permeability variations in predicting the performance of water floods in depleted reservoirs. PERMEABILITY AND CAPACITY DISTRIBUTION It is generally agreed by most investigators that in a single phase system fluid will flow in a porous and permeable medium in proportion to the permeability of the medium. Producing formations are usually highly irregular in permeability, both vertically and horizontally. However, zones of higher or lower permeability are often found to exhibit lateral continuity. Thus, while structurally comparable stringers in adjacent wells may differ several fold in permeability values, they usually bear resemblance as being part of a general continuous higher or lower permeability section. It is generally agreed that where such stratification of permeability exists, injected water sweeps first the zones of higher permeability, and it is in these zones that "break-through" first occurs in the producing well. It is a basic assurnption of the presently described method that penetration of a water front follows the individual permeability variations as if such variations were continuous from input to producing well. This is admittedly not rigorously true, but can be justified as making possible a simplifying mathematical approach to an otherwise extremely complicated three dimensional flow problem. As a basis for study of the lateral flow of fluids in formations of irregular permeability, the irregularities may be conveniently represented by a permeability distribution curve and a capacity distribution curve. In obtaining these curves, the permeability values, regardless of their structural position in the formation, are rearranged in order of decreasing permeability. If these permeability values so arranged are plotted against the cumulative thickness, a permeability distribu- tion curve is obtained. This curve may then be likened to a "smoothed" permeability profile of the formation. In making comparison between different distribution curves it is convenient to state the permeabilities in terms of the ratio of the actual permeability values to the average permeability of the formation. These ratios termed "dimensionless permeabilities", are used in this paper rather than the permeabilities in terms of millidarcys. The capacity distribution curve is a lot of the cumulative capacity (starting with the highest permeabilities) versus the cumulative thickness. The capacity and thickness are given as fractions of the total capacity and thickness. Mathematically, the capacity distribution is the intergration of the permeability distribution curve. In practice it is convenient to first obtain the capacity distribution curve and derive from it a smoothed dimen-sionaless permeability curve. The method of obtaining the capacity distribution curve is illustrated in the successive column of Table 1, in which capacity and thickness are derived as fractions of their respective totals. If only a small number of permeability values are available, it is generally desirable to smooth the resultant curve. This has been done to give the capacity distribution curve shown in Figure 1. The differentiation of the capacity distribution curve to obtain the permeability distribution curve is shown in Table 2. Here, the capacity values are read from the smoothed curve at intervals of cumulative thickness, and the increments of capacity are divided by the increments of thickness to obtain the dimensionless permeability, K. Due to this stepwise procedure of calculation these premeability values must be plotted at the midpoints of the successive increments of thickness. The curve so obtained from these data is shown in Figure 1. The total area under the K' curve is equal to unity.

Jan 1, 1949

By Ware AR, Doyle BJ, Hoogvliet H

The Ladolam deposit lies within the altered volcanic rocks of the caldera floor, part of which now forms Luise Harbour. It was discovered in 1982 in the course of a reconnaissance drainage sediment sampling programme. This was designed to follow up indications of surface hydrothermal activity noted by Government geologists during an earlier survey of the Tabar-Feni island chain. Diamond drilling began in September 1983 and by the end of 1989 a payable and proved mineable reserve containing 19 million ounces of gold had been established. Rock types and structures are masked at the surface by intense alteration and weathering. An extensive drilling programme has enabled the identification of these features and the relationships between them necessary for an understanding of the factors controlling gold mineralisation. It has also led to the recognition of two distinct phases of alteration. The first phase of porphyry-style potassic alteration was followed by violent caldera formation, producing extensive brecciation and veining. The second alteration phase partly over- printed the first phase and was an epithermal one, evidenced by argillic, advanced argillic and phyllic assemblages. During this event, a large volume of fluids circulated under the favourable structural conditions; these fluids included a sulphur- rich, neutral chloride brine believed to have transported the gold. Boiling and mixing of circulating fluids in the open breccias is thought to have resulted in deposition of the gold. There is evidence that this process is continuing at the present day.

Jan 1, 1991

By A. Noble

For the past 30 years, process flowsheet design has been accomplished largely through modeling and simulation. This approach provides circuit designers the freedom to test various separation approaches while minimizing physical and human resource requirements. The Limn® software provides a unique approach to process simulation, through a Microsoft Excel interface. While the software comes with standard process models for numerous unit operations, the Excel calculation environment and the accompanying VBA platform provide a convenient interface for custom model integration, even for non-experienced programmers. This feature is especially useful for university students in introductory process modeling and simulation-assisted flowsheet design courses as well as experienced practitioners with proprietary process models. This paper shows how the Limn® software may be used to solve basic process engineering problems as well as more comprehensive circuit design challenges. Industrial examples as well as opportunities for training and education are presented.

Feb 23, 2014

By B. Goard

"IntroductionCemented backfill has been placed underground in slurry form in Inco Limited's Ontario Division mines since the early 196Os. The slurry was traditionally mixed on surface at between 65 and 70 wt% solids* and transported underground via gravity through a borehole-pipeline distribution system. This method of placement, while simple and dependable, has proven to be costly because of the large amounts of transport water involved.A significant quantity of the slimes buildup on mine levels is caused by the backfill water carrying cement and other fine material out of the stopes. The level cleanup and eventual pumping or hoisting of the slimes and water back to surface result in substantial indirect backfilling costs.The cement that remains in the stope is always overhydrated because of the high water cement ratios that exist. As a consequence, high concentrations of Portland cement must be added to the backfill to produce the fill strengths required for the different mining methods.Pouring backfill at these densities also demands extensive fill preparatory work in the stopes to withstand the hydraulic heads created by the slurried fill. This, along with the delays in pouring necessary to allow for water drainage, result in significant losses in productivity.These negative aspects of slurry placed fill has led Inco Limited to investigate several methods of transporting backfill underground via pipeline, at higher densities (i.e. 75 to 95 wt.% solids). Three separate transport methods are presently being experimented with by the Company's Mines Research Department. Each utilizes a different technique or form of flow transport, i.e. concrete pumping technology, high density slurry flow, and pneumatic conveying."

Jan 1, 1987

By D. Swanson

Cold Detonation Physics (CDP) is a patented new field of explosives and the name for the explosive that is produced when non-toxic dry ice (frozen carbon dioxide) is combined with powdered metals such as magnesium and aluminum, which are non-toxic and nitrogen-free. The explosive is detonator-sensitive and detonates according to the rapid reduction of carbon dioxide back to carbon, which produces solids comprised mainly of metal oxides and about 5% carbon. CDP was determined to produce a maximum of 300 liters of carbon dioxide per kilogram (4.81 ft3 /lb) and about 1.5 liters of carbon monoxide per kilogram (0.024 ft3 /lb). Both these figures shift according to metal content where higher metal produces less gases. According to theoretical modelling, the relationship between static pressure and metal content was determined to be an inverse parabolic curve with optimum pressure at 25% to 31% metal, depending on the type/s of metal/s used. Velocity of Detonation (VOD) was determined by measuring light at the wavefront with fiber-optic cable inserted into a series of holes drilled into the side of a 3-inch diameter (76 mm) schedule 40 steel pipe containing the mixture. The highest VOD was observed at 25% magnesium and measured between 2,500 to 4,500 m/s (8202 to 14,764 ft/s) when initiated by a 454-gram (1-pound) booster and an electric detonator. A 25% 50:50 alloy of magnesium and aluminum sample shot at a higher velocity than magnesium, according to how the alloy generated smaller pieces of shrapnel when compared with shrapnel from a magnesium test. CDP, using 25% alloy, was tested for blasting limestone by drilling 3.5-inch holes (89 mm) and inserting a 3-inch x 4-foot cardboard tube (76 mm x 1.22 m) with the mixture, packed to a density of 0.62 g/cm3 . The blast was initiated with an electric detonator, behaved like ANFO with more energy and fractured rock sufficiently across the entire length of the borehole. Seismic analysis determined that CDP produces lower ground vibrations than traditional explosives.

Jan 1, 2024

By Derek du Preez, Andrew Hall, Timothy M. Pelech

Net Present Value (NPV) derived from Discounted Cash Flow (DCF) analysis remains the dominant metric for evaluating mining projects despite its well-documented inability to capture managerial flexibility under uncertainty. DCF assumes that all risks are perfectly priced by financial markets. This is an unlikely assumption for volatile commodity prices, geological variability, or the array of mining technical and operational risks present on all mine sites. Real Options Analysis (ROA) was developed to remedy this limitation by explicitly valuing the ability of managers to defer, expand, scale, switch, or abandon investments as new information emerges, and to capture upside and mitigate downside risks. While ROA is philosophically correct and routinely shows an uplift in project value compared with DCF, its practical application at industrial scale is severely constrained, ROA faces the reality of a combinatorial explosion in complexity of decision trees, Monte Carlo simulations and other models required when multiple interdependent or sequential options exist across numerous mining zones and time periods. The AMC Hill of Value® (HoV) process adopts the same intellectual foundation as ROA, that flexibility has economic value, but operationalizes it through a far more robust and scalable architecture. It is built on parametric relationships, rapid scheduling, and multi-objective evolutionary optimisation. HoV can evaluate millions of compound, interdependent real options in a single optimisation run, delivering resilient, adaptive strategies that preserve managerial flexibility while simultaneously optimising NPV, mine life, risk exposure, and other corporate objectives. This paper demonstrates that HoV is the practical, industrial-scale embodiment of real options thinking in mining: it discovers, ranks, and translates the most valuable real options into strategic mine plans, overcoming the scalability barriers that have prevented widespread adoption of classical ROA.

Feb 22, 2026

By M. I. Mthenjane

"BackgroundThe paper discusses post-mining land use however, the essence of the topic is the emotional motivation behind the decisions related to mining investment and development. Therefore this is not a typical SAIMM technical paper about the science and techniques of post-mining land use. There are already numerous papers written and conferences held on this aspect of post-mine land use; the science is well understood, but the evidence of the practical application of the (environmental, social, and economic) science is sparse. At a recent conference held in November 2017 on the theme of ‘Science, Business, Society Dialogue – linking science, society, business and policy for the sustainable use of abandoned mines in the SADC region’, it was demonstrated through the delivery of several papers on the possible viable options of post-mine land use. The conference was structured in nine sessions, covering the following relevant topics:? Sessions 1 and 2: Nature and magnitude of the problem: raising awareness? Sessions 3 and 4: International experiences in remediation: case studies? Sessions 5, 6 and, 7: Technological solutions: converting liabilities into assets? Session 8: Implementing solutions: social and legal aspects? Session 9: Wrap up, lessons learned: conference resolution.Summaries of the key outcomes of the sessions are available for reference.The aim of this paper, accompanied by the video speech, is to provide a visualization of the possibilities of post-mine land use. Mining contributes approximately 7% to South Africa’s GDP - this is the lowest it has ever been and is attributable to both a diversifying economy and to poor mining and investment policy which has resulted in reduced investment in the sector. The objective of the paper is to highlight the opportunities, for succeeding and diversifying economic activity following mining and mineral extraction which can continue to sustain the livelihoods and wellbeing of communities and societies beyond mining.During mining, very few alternative and local economies develop. Dependence on mining and its value chain prevails until mining ceases. This idea is conveyed in Figures 1a and b."

Jul 1, 2019

By A. Dave Mackintosh

In 2001, at the CIM AGM in Quebec, a paper discussing poor ground conditions in a newly opened area at Agrium?s Vanscoy Potash Operation?s, suggested load transfer around old workings as a possible reason for the early room failure. High closure rates are expected in deeper regions however the rapid failure of walls immediately behind the face resulted in protective guards being mounted on and behind the borer. The high closure and early rib failure continued well past any reasonable distance to be explained by load transfer around old workings and investigations continued into possible reasons other than simply depth. Detailed investigations into the mineralogy and crystal fabric of the ore zone provided one possibility, which combined with a changed borer cutting profile are now believed to have contributed greatly to the poor conditions.

Apr 1, 2005

Recycling of Sludge from the Production of Manganese

Sep 13, 2010

"The objective in controlled blasting is to reduce overbreak to control the final pit wall slope, shaft, drift ditch, bench, etc. to the final planned excavation limit. The six main types of controlled blasting utilized today are:1. Line Drilling2. Cushion Blasting3. Smooth Wall Blasting4. Buffer Blasting5. Presplitting or Preshearing6. Air Deck Presplitting"

Jan 1, 1994

Flow Sheet Development of Three Geographically Distinct Chromium-Bearing Ores

Sep 13, 2010

By W. R. Ingalls

DUPING the last two years, and especially during the last six months, a number of important articles upon the new methods for the desulphurization of galena have been published in the technical periodicals, particularly in the Engineering and Mining Journal and in Metallurgie. I proposed for these methods the type-name of "lime-roasting" of galena as a convenient metallurgical classification,' and this term has found some acceptance. The articles referred to have shown the great practical importance of these new processes, and the general recognition of their metallurgical and commercial value which has already been accorded to them. It is my present purpose to review broadly the changes developed by them in the metallurgy of lead, in which connection it is necessary to refer briefly to the previous state of the art. The elimination of the sulphur-content of galena has been always the most troublesome part of the smelting-process, being both costly in the operation and wasteful of silver and lead. Previous to the introduction of the Huntington-Heberlein process at Pertusola, Italy, it was effected by a variety of methods. In the treatment of non-argentiferous galena concentrate, the smelting was done by the roast-reduction method (roasting in reverberatory furnace and smelting in blast-furnace); the roast-reaction method, applied in reverberatory furnaces; and the roast-reaction method, applied in Scotch hearths 2 Precipitation-smelting, simple, had practically gone out of use, although its reactions enter into the modern blast-furnace practice, as do also those of the roast-reaction method.

Sep 1, 1906

By David B. Reger

New discoveries of gas in the southern counties featured the petroleum industry in West Virginia during 194;. Drilling for oil increased slightly over 1944 and a small increase of initial production resulted. Out of 28 wildcats drilled, there were 16 gas discoveries and 12 dry holes. No commercial oil was found in the 28 wells.

Jan 1, 1946

By R. Heersink, C. H. Wells

Innovations in communications and real-time information systems are providing industry opportunities to improve profitability. Real-time operating data is collected from equipment across a site or even several sites into a central server for secure PC and PDA-based Internet access. This paper includes discussion of how operating staff can use wireless devices to see equipment and processing data from anywhere throughout the mines and concentrators, and how management can view results from multiple mines, all in real time. Additional opportunities enabled through the remote access by equipment vendors or mining consultants is also presented, as well as an overview of typical benefits and current installations.

Jan 1, 2002

The regular activities of the Institute are financed mainly by income derived from members' dues, from advertising in MINING AND METALLURGY, and from the sale of publications to the public. In addition, collateral activities and special projects are financed each year by means of income from endowed funds controlled and administered by the Institute. In the aggregate, the principal sums of these endowments amount to more than $530,000. An active effort is being made to increase the endowment funds of the Institute through a standing committee, of which H. T. Hamilton is chairman, and of which the other members are: W. H. Aldridge, George D. Barron, Cleveland E. Dodge, D. C. Jackling, Henry Krumb and J. V. W. Reynders. This committee feels that there exists a tremendous opportunity for the Institute to be of ever-growing service to the public, to the mineral industries, and to the profession. It welcomes suggestions as to names of men of means who are vitally interested in the mineral industries, and to whom the opportunity to make a contribution or bequest might appeal favorably if presented in the proper light by the committee.

Jan 1, 1941

By J. Ran

There are challenges in mining deep tabular ore deposits using the open stoping method, particularly mining remnant panels towards the end of mine life. The remnant panels have experienced stress concentration and are in the failing or post failure state causing drilling and loading difficulties, ground movement, induced seismicity and ground instability problems. As more mines are going deep, without effective ground control management, the mine production will be interrupted and equipment damage and personnel injury are likely to occur. Mining at Falconbridge Lockerby Mine located in the Sudbury Basin was concentrated in the deep zone from late 1990s to 2004. The remnant panels situated approximately from 1800m to 1920m below surface were mined in 2004 before the mine closure. These panels were in the central section of the orebody along strike. The orebody was relatively narrow ranging from 5m to 15m and steep dipping at 70o to 80o. Because of the retreat mining sequence and the mining depth, stress concentration, wall closure and seismicity had caused a number of mining difficulties. Managing these challenges was critical in achieving the mine production target without compromising personnel safety and excavation stability. A comprehensive ground control management approach was adopted to mine the remnant panels at depth. The measures taken included ground movement monitoring, understanding the movement pattern of the footwall rock and selecting appropriate support systems, analyzing seismic monitoring data and defining re-entry protocol, brow support design and restricting access. This paper presents these ground control measures and the experience gained in successfully mining the deep remnant panels at Lockerby Mine.

Apr 1, 2005

[ ]

Jan 1, 2009

By F. W. Jessen, C. C. Patton

Adsorbed films were formed on polished stainless steel specimens from dilute benzene solutions of two crude oil distillation residua. Although the two residua were extremely dissimilar in composition, contact angle measurements showed that the two films increased the wettability of the steel specimens to oil by equal amounts. Furthermore, the wettability of the films was essentially unaffected by the desorption techniques used. Paraffin deposits were formed from heptane-wax solutions on the same stainless steel specimens. These deposits definitely adhered to the surface. Presence of an adsorbed crude oil film on the metal surface increased its free surface energy and resulted in increased deposition of paraffin. The addition to the heptane - wax solution of small amounts of the same distillation residua that were used to form the adsorbed films resulted in decreased cohesive strength in the deposits formed, which resulted in decreased deposition. The presence of a crude oil fraction both in the solution and as a preadsorbed film eliminated the adherence of a deposit of any kind. A mechanism of deposition is proposed which explains the results obtained. INTRODUCTION The natural formation of any predominantly organic accumulation in oilwell tubing, surface flow lines or other production and storage facilities is called a paraffin deposit. These deposits restrict the production of crude oil, causing a substantial increase in production costs because of decreased flow capacity, expense for periodic deposit removal and unproductive downtime. The conditions under which such deposits form, their physical characteristics and the nature and severity of the problem created are extremely varied. Over the past several years, much progress has been made in developing and utilizing methods to remove accumulated paraffin deposition. However, like so many other problems, the basic stumbling block appears to be a lack of understanding of the fundamental mechanism involved in the formation of such deposits. Crude petroleum is known to contain considerable quantities of polar, surface active substances which Doddl has shown to be present at the oil-water interface. Denekas, Mattax and Davis2 observed that the wettability of reservoir rocks was drastically altered by exposure to crude oil fractions; and Zisman, et a1.3 showed that the nature of the compounds adsorbed on a surface would determine its wettability characteristics. Cole and Jessen4 and Ehrig5showed that surface wettability can have a profound effect on the magnitude of paraffin deposition, and Parks6 demonstrated chat the presence of certain adsorbed films on a metal surface would reduce the adherence of paraffin to that surface. Zisman7 has since advanced the theory that the conditions for adhesion are the same as for wetting. Therefore, it was felt that there was adequate evidence to support the supposition that adsorption of compounds from a crude oil might play an important part in paraffin deposition. ADSORPTION-WETTABILITY EXPERIMENTS Initial experiments were conducted to determine the effects of adsorption from solution of crude oil residua on the wettability of a polished stainless steel surface. Distillation residua with initial atmospheric boiling points of 700F were used in preference to the whole crudes in order to concentrate on the molecular weight range of interest, and to eliminate the possibility of composition change due to evaporation of the light ends. Also, these high boiling materials would be expected to be adsorbed from the whole oil in preference to similar compounds of lower molecular weight.

Jan 1, 1966

By R. K. McLimans, C. Knudsen, S. Bernstein, D. Frei

Computer Controlled Scanning Electron Microscopy (CCSEM) is used to analyze indivdual mineral fractions in heavy mineral sands. CCSEM is a fully automated particle analysis technique for the determination of physical and chemical properties of a large number of individual particles. CCSEM enables the precise and accurate determination of the modal abundances of individual mineral fractions (e.g. ilmenite, rutile, zircon, or garnet), their average chemical composition (and compositional variation), as well as their physical properties such as size (e.g. diameter and perimeter length) and shape (aspect ratio and circularity). A unique sample preparation procedure is used to produce representative polished sections from cylinders of raw sand samples such that thousands of grains are present in a polished cross section, but grains are not touching. The combination of this sample preparation technique with CCSEM enables the fully automated analysis of individual grains without the application of de-agglomeration or erosion steps to separate touching particles. Hence, CCSEM yields information representative of the entire area of analyzed grains without systematic bias due to neglect of rim areas by de-agglomeration or erosion steps. Therefore, the resulting data are determined with high accuracy, precision and statistical validity. Because the sample preparation is relatively straightforward, using raw sand samples, and all chemical and physical properties are determined in one analytical session per sample, CCSEM is a powerful cost and time efficient tool for characterizing chemical and physical properties of minerals in heavy mineral sand deposits.

Jan 1, 2005

IN presenting a'description of milling and treatment methods at the Waihi mine, it is advisable to first traverse a good deal of the past history of the mine, and show the various steps which have led up to present-day practice. The record of the company is one of steady, solid advancement, both in metallurgical and financial results. This is illustrated by the following figures, dating back from 1897...

Jan 1, 1912