Search Documents

By W. F. Rochow, W. C. Burke

Numerous designs of linings and accessories, including dams, lifters, and heat exchangers, contribute greatly to kiln efficiencies. Greater conductivity is achieved with basic brick than with fireclay and high-alumina refractories, depending largely upon the use of steel plates in radial joints between adjacent brick to increase heat transfer through the lining. Refractory lifters expose all portions of the load to radiant or convective heat and raise some portions to higher temperatures by cascading the load down through the path of the hot gases.

Jan 3, 1955

SOME notes on the works of the Electrolytic Refining and Smelting Company of Australia will no doubt be of interest to members of the Institute, more especially as much of the work is new to Australasia. As many of the members who may read this paper have not been in a position to visit works of this kind, and are consequently not thoroughly acquainted with all the operations carried on, the author has taken the liberty, in some cases, to enter into explanation which would otherwise be unnecessary. The works are situated at Port Kembla (New South Wales), about fifty miles south of Sydney, and are approachable both by rail and water. The Government has recently built a low-level jetty upwards of five hundred feet long, and intends installing at an early date an electrically operated portable crane to facilitate the handling of material to and from the boats. This will mean: a considerable reduction in the length of time that boats are laid up at the jetty. There are also under construction two breakwaters, which, when complete, will materially assist shipping operation...

Jan 1, 1910

Efficiency, Economics, Energy and Emissions - Emerging Criteria for Comminution Circuit Decision Making

Sep 13, 2010

By Andre Zingano

The objective of this paper is to compare the behaviors of different types of roof bolts: (1) One-Step Bolt (OSB), (2) Fully grouted Bolt (RB), (3) Combination Bolt (CB), and (4) Torque tension Bolt (TB). Two dimensional numerical models were built for both bolted and unbolted roofs. The geological sequence and rock properties used in the numerical models represent the typical roof condition for Pittsburgh coal seam. Using the unbolted roof as a base case, a comparison is conducted by monitoring the roof vertical displacement at the center of the entry and at the bolt positions, the axial force in the roof bolts, and stress distribution in the bolted area. The grout/rock interface is assumed to be perfect. The estimated roof displacements showed that the differences among the four types of roof bolts are small. The major differences are in the shear stress at the grout/rock contact and in the shear stress along the immediate roof bedding interface as well as in the bolt axial stress. There is less axial stress for the OSB compared to RB and CB as the diameter of the OSB is much bigger and the contact area between grout and rock is twice as large as for RB and CB. The higher strength of the OSB contributes to keep the bedding planes in the roof closed.

Jan 1, 2007

By D. R. Rathburn

Jan 1, 1962

By Sidney Katell

This report is the fourth in the series, Bibliography of Investment and Operating Costs for Chemical and Petroleum Plants. The initial work, Bureau of Mines In- formation Circular 7516, was published in October 1949 in conjunction with the synthetic liquid fuels program authorized by Public Law 290, 78th Congress. It included references to and abstracts of publications appearing from 1930 to September 1948 on all processes in general use in the petroleum refining and chemical industries. A supplemental bibliography, Bureau of Mines Information Circular 7705, was published in January 1955 to cover the period September 1948 through June 1952; and Supplement 2, Information Circular 7751, published in September 1956, covered the period June 1952 through June 1954. The present supplement covers the period July 1954 through December 1956.21 The information in this paper was obtained from the following sources: 1. Bureau of Mines Information Circulars. 2. Bureau of Mines Reports of Investigations. 3. Chemical Engineering. 4. Chemical Engineering Progress. 5. Chemical Engineering Costs Quarterly (Cost Engineering).

Jan 1, 1958

By S. A. Luciani

"In 1957, an asbestos orebody was discovered in the northern sector of the Ungava Peninsula of the Province of Quebec, an area now identified as Asbestos Hill. The deposit is situated on a plateau 1700 feet above sea level and 42 miles inland from Hudson Strait. It is a bleak, iso. lated location of typical arctic environment. Fifteen years were to pass before the first shipment of ungraded fibre was made in 1972. These years we1•e occupied with field surveys and investigations, diamond drilling, engineering design, evaluation of investment and operating costs, and construction. The problems normally associated with mine development were further complicated by location, isolation, and the extreme cold and permanently frozen ground of the arctic regions. Unique to an isolated arctic operation are the organization of support facilities and services, procurement and retention of personnel, construction of access roads and airports, and scheduling of product out and supplies in during the short summer period of sea navigation."

Jan 1, 1976

By P Standish

Qualitative risk assessment methods are not well suited to considering complex systems and potential interactions of new technology. As part of supporting tier one mining organisations and international industry groups, the author and colleagues have innovated processes to help provide better solutions to sites/companies considering a move to implementing proximity detection and collision avoidance systems. The process identifies required operating states for the system. By applying a combination of research and team-based analyses, a rigorous identification of credible failure modes which could cause these states to be lost, is identified. Finally, required business inputs, expressed in practical terms are distilled from regulator, industry, organisation and site in a way which clearly addresses the failure modes and so retain the required operating states. These business inputs identify improvements for site arrangements (EMESRT levels 1 to 7) before identifying functional requirements for technological collision avoidance solutions (levels 8 for advisory and 9 for autonomous). The paper presents a case study synthesised from multiple sites analyses and will provide guidance on where to find additional resources to assist in making the best possible transition to better equipment and road network solutions.

Jun 22, 2022

Refractory gold ores have been the subject of intensive metallurgical study in order to achieve more efficient recovery of contained values and at the same time to minimise environmental impact. Considerable innovative gold processing technology was introduced in New Zealand last century, the most notable being the first successful commercialisation of the cyanidation process by the Crown Mines Company at Karangahake in 1889. The Karangahake gold-silver deposit was second only +to the Waihi Martha mine in total bullion production from the region with active mining from 1882 until about 1920 and sporadic production between 1930 and 1944. Reevaluation at Karangahake with associated metallurgical testing has continued since that time becoming particularly active in the last decade as a result of increasing gold prices. Gold processing technology is reviewed and results of some recent test work are presented and discussed in the context of Karangahake history and future development possibilities. This work confirms the variability and complexity of the Karangahake deposit both mineralogically and metallurgically and suggests flotation followed by new and innovative smelting is the most appropriate processing route for the recovery of gold from the high grade ore which could be produced from the Karangahake workings in moderate tonnages.

Jan 1, 1993

By T G. Neville, G Terrey, J Burns

This paper explores recent industry training programs and lessons for supervisors. The Belbin Team Role model was used to increase participants’ awareness of behaviour and its application. The application of the Belbin model to underground, open cut mine and quarry supervisors is discussed.The key to team success may rest with the expertise and experience of its members, but increasingly effectiveness depends on how team members understand, acknowledge and support each other’s behavioural strengths. Discovering strengths is a challenge, both for their measurement and for the encouragement of team members to use the knowledge of themselves and others in the team. Using behavioural models provides a constructive approach and a language for supervisors as they build personal motivation and engagement.Prima facie, the mineral industry’s work may be too vigorous for teams and their managers could be more prone to use ‘solo’ or traditional management styles. Managers and supervisors must know when work allocated to a team is appropriate or where individual effort should be applauded and rewarded. For practical people with well-developed technical skills, improving the soft skills necessary for a supervisor requires some reflection and effort. The Belbin behavioural model can be an effective tool for recognising characteristics that can assist teams to be more productive.Experiencing the Belbin Team Role model as part of an industry qualification is important for supervisors studying to refine their team leadership skills. Data are available for participants to assess the nature of their teams and to confront the appropriateness of the behavioural mix for the work of the team and its individual members.So what are the next steps? All team development must have a place in the strategic thinking and plans of the enterprise. This needs a visible presence of senior managers and supervisors in managing a team culture with practical links to workplace priorities and professional development with continuous improvement.CITATION:Burns, J, Terrey, G and Neville, T G, 2016. Supervisors and teams at work, in Proceedings International Mine Management Conference, pp 125-138 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By Olaf Andersen

Crucible melt extraction yields short metal fibers with eqivalent diameters as low as 50 µm from almost arbitrary metals and alloys. Highly porous components can be made from such fibers by suitable deposition and sintering methods. This technology is being developed at the Dresden based Department of Powder Metallurgy and Composite Materials of the Fraunhofer Institute for Manufacturing and Advanced Materials (IFAM) and has been applied to gold alloys and iron-base alloys containing small additions of precious metals. From the manufactured gold fibers, sintered structures were made for decorative applications. Additionally, it was found that due to rapid solidification during the fiber formation, precious metals can be finely dispersed in ironchromium- aluminum (FeCrAl) and FeAl20 alloys. Good catalytic activity at elevated temperatures was found in compositions containing 3 wt.-% Ce and 0.5 wt.-% Pt.

Oct 1, 2003

By A D. Stewart Gillies

Resource rent taxes are taxes which only become effective at such a time as a pre-determined rate of return has been achieved by an operation. Resource Rent Taxes have from time to time been considered for implementation in bothAustralia and New Zealand. The offshore petroleum industry in Australia is already subject to RRT as is the Roxby Downs (Olympic Dam) Mine in South Australia. Both the mining and petroleum taxation regimes in Papua New Guinea include a resource rent tax component called Additional Profits Tax.   The implications of the current form of additional profits tax for shareholder cash returns are that the tax burden on the operation may suddenly increase at some stage in the life of the mine if and when the threshold level of profitability for the tax to be triggered is exceeded. From that point in time onwards the cash return to the shareholders on the capital invested is greatly diminished. For mining companies in Papua New Guinea, the effective tax rate increases from 35% to 57.75% as a result of the onset of additional profits tax. This tax rate penalty is so severe that there appears to be merit in considering the concept of managing profitability through time rather than purely maximising annual pre-tax profits as is currently the case in most mining operations. This would have the benefit of deferring or perhaps preventing altogether the onset of the tax. One possible method for the effective management of profitability is through the control of average mining grade by cutoff grade manipulation.   Traditional cutoff grade theory has usually considered taxation as a direct cost at a fixed or variable percentage of annual profits. As a result of this most analyses are conducted on a pre-tax basis. If tax is included in analyses it is usually present as a time independent function of gross profit. Additional profits tax is both time, and rate of return dependent and therefore not adequately accommodated by currently accepted cutoff grade theory.   A review has been made of the effects of resource rent taxes on both the investment decision-making process as well as possible development and mining strategies which may be employed by mining companies faced with resource rent taxes. The review includes examples based on the structure of additional profits tax which is levied in Papua New Guinea.

Jan 1, 1995

By A. J. Van Der Merwe, N. A. Barcza, M. Boyes, N. R. Clarke

Oriel Resources has with the support of SRK (Cardiff) and DRA and Mintek (South Africa) carried our a Definitive Feasibility Study (DFS) to recover high grade chrome ore from its Voskhod deposit very close to Chromtau that is near to Aktobe in Kazakhstan. Voskhod is a large podiform ore body that contains nearly 20million tons of chromite grading about 48% Cr2O3 and with a Cr/Fe ratio of over 3/1. Selected bore hole core samples were obtained from the confirmation drilling programme during the DFS phase of the project in 2005 for pilot plant test work to design the mineral beneficiation plant. The chrome ore is characterised by four main types, namely high grade lumpy and chip sized ore, high-grade fine ore, lower grade (subordinate) lumpy ore and lower grade fine ore. Gravity separation tests carried out by Mintek showed that the large density difference between the high grade (at over 3.7t/m3) and lower grade ore (at less than 2.97t/m3 ) should ensure very good separation in the DMS drum and DMS cyclone stages resulting in high recoveries of Cr2O3 - rich chromite ore products. Very high chrome ore grades of up to 64% Cr2O3 and Cr/Fe ratios of 4 to 1 were obtained at an 80% mass yield from selected samples of lumpy and chip ore size fractions. The overall predicted recovery from the design work on the mine and plant is expected to be closer to about 70% of the ROM (Run of Mine) feed. DRA has completed the design of the mineral processing plant to recover about 900 kt/a of chrome ore from the 1.3 Mt/a of ROM feed. The plant has been sized to handle up to 1.5 Mt/a and will also be able to address the variability in ore feed as different regions in the deposit are mined. The lumpy high-grade product and the chips size fraction is expected to grade around 48% Cr2O3 and the fine concentrate between 56 and 58%Cr2O3 The ratio of products is expected to be about 70, 15 and 15 percent respectively but will vary to some extent during the expected 20 year life of the mining operation based on including the associated adjacent Karaagash deposit together with the Voskhod deposit. The prediction of the product split from the processing plant depends on many factors such as the geology, mineralogy, mining, handling and metallurgical processing. An overall process flow model has been developed that covers the ROM ore, the various types of chrome ore feed to the mineral beneficiation plant, the projected products and the subsequent smelting of the chromite ores to produce High Carbon Ferrochromium. The model allows the optimisation of the quality of the chrome ore in terms of Cr2O3 content, Cr/Fe ratio and recovery to be studied. This information can also be evaluated in terms of the economic requirements for smelting High Carbon Ferrochromium (HCFeCr) at a given location. Oriel is planning to supply chrome ore to Ferrochrome plants mostly in China and Russia. The use of the model will assist to maximise the value of the Voskhod project to its owners and also assist the users of the chrome ore in selecting the appropriate supply quality to meet their needs for a given smelter operation. The smelting of high grade Voskhod ore requires a limited addition of about 5 to 7% quartz to flux the MgO and Al2O3 and about 25% coke as a reducing agent to produce an alloy containing from about 65 to 74%chromium depending on the Cr/Fe ratio.

Jan 1, 2007

By Jan E. Nesset, Julie Fournier, Jorge Torrealba, Colin Hardie

"Gas dispersion studies have been used to benchmark and optimize plant flotation performance for more than a decade, although this technology is not as widely in use as it likely should be based on the significant improvements that have been reported. Part of the reason may be a general lack of awareness within the industry of just what these improvements have been. This paper reviews a number of the reported case studies, groups them into categories of improvement, and draws some general conclusions. The paper will be of interest to plant engineers and technology providers seeking new approaches and tools for improving their own and clients’ processes.INTRODUCTIONThe sector of flotation hydrodynamics that is now known as gas dispersion technology, and the corresponding terminology, had its beginnings in the 1980’s and early 1990’s in the laboratories of McGill University where the students of Prof. J.A. Finch and Dr. C. Gomez conducted studies of gas holdup, superficial gas rate and water recovery on laboratory flotation columns (Laplante et al., 1983; Xu et al., 1991;, Banisi and Finch, 1994; Finch et al., 1999; Nesset, 2011). Sensors were developed for gas holdup (eg), gas rate (Jg) and bubble size (Db) distribution (Tavera et al., 1996: Finch et al., 1999; Dahlke et al., 2001; Chen at al., 2001; Hernandez-Aguilar et al, 2002, 2005). The sensor measurements were rapidly adapted for use in mechanical flotation machines in plant environments (Gomez and Finch, 2002; Gomez et al., 2003; Cooper et al, 2004; Torrealba-Vargas et al, 2004; Nesset et al., 2007). Somewhat parallel developments were being conducted by Gorain and colleagues at the University of Queensland’s JKMRC on pilot and industrial flotation machines using the McGill approach but utilizing alternate sensor designs for eg, Jg and Db (Gorain et al., 1997, 1999; Schwarz and Alexander, 2006) to link flotation kinetics to bubble surface area flux (Sb). Early industrial applications were those led by the university teams from McGill (Canada), the JKMRC (Australia) and the University of Santa Maria (Chile) at plants in North and South America, Australia, South Africa, Asia and Europe. Industrial organizations that brought the technology on-board in the early 2000’s included Teck Resources (then Teck Cominco), COREM, Vale (then Inco), Anglo American Platinum. Several of the major flotation cell manufacturers also purchased the McGill bubble viewer technology for their own equipment studies. The sensors have continued to evolve with multiple and continuous measurement of Jg (Torrealba-Vargas and Finch, 2006, Bartolacci et al., 2008), gas holdup by acoustic means (O’Keefe, 2007) and a combined Jg-Db device called the Anglo Bubble Sizer (Harbort and Schwarz, 2010). A review of the gas dispersion technology use and development have been provided by Gomez and Finch (2002), Harbort and Schwarz (2010) and Nesset (2010)."

Jan 1, 2015

By J. R. Parga

In mineral processing, poor froth-flotation performance translates into both an enormous loss of revenue and an unnecessary waste of the ore reserve. In this context, Bacís Mining Company developed a versatile new, high-performance flotation-cell design that can be incorporated into various flotation circuits. The main feature of this circular cell is that it is comprised of two separate sections, namely, a flotation cell that uses wash water to minimize the entrainment of fine gangue particles into the froth product and an external bubble generator that produces small bubbles of relatively uniform size at a specified aeration-rate. The air/water mixture is blended with the pulp by gentle agitation, so as to enhance particle-bubble aggregate-stability. Comparative metallurgical performance with conventional flotation cells show that the power requirements and operating costs for precious metal flotation are three times lower, while the concentrate grade is 7% higher and the recoveries of precious metals are 5% higher.

Jan 1, 2009

By Henry S. McDevitt

External Shock Mitigation (ESM) is being studied as a possible means of retrofitting existing buried structures to provide additional protection from ground shock. As part of this study, two tests were conducted on four ESM models and a control structure. The test articles were placed at a carrnon distance and subjected to the ground motions created by a buried explosive charge consisting of 2,ODO pounds of nitranethane (NM). Adequate instrumentation data were obtained to assess the response of the four ESM models. The assessment relied heavily on direct comparison of horizontal motions measured in the models, with similar measurements in the control structure. From the tests, it was observed that peak accelerations were reduced by a factor of 5 by the ESM. However, the particle velocities and displacements were not significantly affected by theEIS.

Jan 1, 1997

By J Light

Since 2019, the mine planning team at Olympic Dam has been establishing and maturing a shift from deterministic to probabilistic scheduling techniques. This paper outlines this journey undertaken by the mine planning team, key learnings from implementation and further work required to increase the level of planning maturity. Olympic Dam (OD) is a highly variable, polymetallic orebody with a vertically integrated value chain from operations to final product. The processing plant has a tight set of quality constraints which are managed through timing of stopes from varying parts of the orebody. Value is eroded for the operation when forecasted quality of the mine feed encounters disruptions from unplanned changes to the timing of stope starts. As production has moved from the historic Northern Mining Area into the more geologically complex Southern Mining Area, average stope size has reduced, resulting in increased mining fronts required to meet production targets. This has created a problem of increased schedule complexity and difficulties in identifying and communicating resource priorities within a large set of individual stope critical paths. The problem was approached by considering each stope as an individual project constructed by teams working across multiple projects at any one time. The operation could then be considered a multi-project environment with shared resources and enables the application of Critical Chain Project Management (CCPM) to the mine plan. Key to CCPM is the addition of time buffers to protect the critical path of a project form upstream or downstream processes. Implementation of time buffers protects the stope start date against compliance to plan variance. The monitoring of each time buffer consumption, as a proportion of total construction activities completed enables proactive prioritisation of resources. This resulted in an increase in the number of stopes starting in accordance with the mine plan, simplified communication of priorities to all levels of the operation, increased compliance to plan and a clear measure of schedule risk during planning routines.

Mar 29, 2023

By Elio Ferreira

This report describes the design, and development work performed to reduce the volume and weight of the miners caplamp battery, as well as a headpiece with a swivel mechanism containing a halogen bulb with two filaments. Work was also conducted in the development of a maintenance free battery. The design concept is based on non-sintered Ni-Cd technology, with an energy density of 22 Wh/lb. The cap lamp system developed has been approved by the Mine Safety and Health Administration (MSHA) and can be manufactured for mine use.

Jan 1, 1988

By Joseph Daly

An investigation into inaccurate scatter of pyrotechnic detonators led to the innovation of utilising existing (every day) equipment in a manner to accurately determine the true scatter of detonators. This can then be utilised to determine the accuracy of a particular batch of detonators.

Jan 1, 2014

By Heithecker R. E.

In June 1933 the Bureau of Mines, in cooperation with the State of Oklahoma and the Oklahoma City Chamber of Commerce,, published a report of the gas reserves in the Oklahoma City oil field3/ based upon data as of October 1932, at which time there were 43 classified gas wells in the field, The estimates were obtained by the ?porosity-area" method. There are two general methods of estimating natural-gas reserves. The porosity-area method, as used by Hill and Rawlins, is used when a gas field is comparatively new but after enough drilling has been done to determine the average thickness, porosity, and areal extent of the producing horizon. The "pressure-volume? method of estimating gas reserves, the method used in this report, may be used after a sufficient volume of gas has bean withdrawn from the reservoir to cause an appreciable decline in reservoir pressure.

Jan 1, 1937