Search Documents

By Hong Yong Sohn, Miguel Olivas-Martinez, Zhixue Yuan

A novel flash ironmaking process that directly reduces iron oxide concentrate particles by gas is under development. The goal of this work was to study the possibility of reoxidation of iron particles in various gas mixtures. As the product iron cools down in the lower part of the flash reactor, conditions may become favorable for reoxidation because of equilibrium and high reactivity of iron particles. The effects of temperature (823 – 973 K) and H2O partial pressure (40 – 100 pct., Ptotal = 86.1 kPa) on the reoxidation rate were examined. The pressure dependence was first order with respect to water vapor, and the activation energy was 146 kJ/mol. A complete rate equation that adequately represents the experimental data was developed. For oxidation in O2-N2 mixtures, the effects of temperature (673 – 873 K) and O2 partial pressure (5 – 21 pct., Ptotal = 86.1 kPa) were determined. Reoxidation in pure CO2 was also investigated at 873 – 1073 K for comparison.

Jan 1, 2014

By S Hanrahan, S McLaughlin

A case study is presented that details the safety journey at a North American project involving two major contracts: a 1000 m shaft recovery and rehabilitation, and the development of a drainage gallery in a large open pit operation. In the early stages of the contracts, there were a number of incidents that created tension between the owner and contractor, which resulted in the contractor being placed on a final warning with almost imminent potential termination. As a result of this, it was agreed to initiate a focused safety recovery plan as a ‘last chance’.Over a period of two years, the engagement and consequent performance of the contractor was turned around, steadily working to set it up for success such that in one of the contract work areas, a record of ‘one year LTI (lost time injury) free’ was achieved. The journey involved the owner and the contractor teams working cohesively to educate all parties in the safety requirements and, most importantly, providing the context and understanding for certain requirements being put in place. Early on in the process, it was recognised that the owner team unknowingly was an impediment in that they did not fully understand the safety requirements and so was not able to lead the way for the contractor effectively. The journey to rectify the situation was supported and followed up by focused engagement with the project team, which generated a progressive improvement in a very challenging environment.In particular, the contractor turnaround was significant and of enough value for the contractor to ultimately export some of the safety systems from this site to other contract sites. This demonstrated the ultimate benefit of the contractor understanding and buying into a safety culture and system.CITATION:Hanrahan, S and McLaughlin, S, 2016. Winning the safety battle, in Proceedings International Mine Management Conference, pp 181-186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By Tristan Worsey, Nathan Rouse

Florida is one of the major limestone producing states in the United States. The state has unique regional geology and groundwater characteristics that require equally unique mining methods to extract limestone for construction materials. In many regions, aggregates quarries operate by drilling and blasting underwater limestone and then digging the muck with large draglines, while in others, mining operations are able to operate above the water table.

Jan 1, 2019

By A. Aly Selim

This report describes the feasibility of predicting percussive drilling rates by equations derived from statistical regression analysis. The least squares statistical method was used and the analysis was performed both by direct and by stepwise linear regression analysis. The predicted penetration rate is a function of the drill power and the physical properties of the rocks penetrated. The results show promise that the technique may be of value in providing a mathematical model by which percussive drill manufacturers and users can predict the performance of a given drill. Experimental work involved two mining type percussive drills. Penetration data for these drills were determined from nine rocks drilled in the laboratory. Drill work rates (power) were determined in a separate series of experiments. Rock physical properties were measured from diamond-drill core samples taken from the same blocks used for percussive drilling.

Jan 1, 1970

By David F. Gearhart

The Burrell Can1 is a thin, steel, tubular shell filled with aerated concrete that is used as a roof support in coal mines. The Can height is always shorter than the mining entry, so it is capped with wooden timbers and wedges when it is installed. This combination of the Can and the wooden header is a standing support system that is designed to yield in a controlled manner and exhibit a constant yield, or elastic-plastic behavior. The Burrell Can is capable of withstanding 20 in or more of vertical convergence and 15 in or more of horizontal displacement. Because of this exceptional ability to sustain load through extended convergence and displacement, it is one of the most robust standing supports in use today. The National Institute for Occupational Safety and Health (NIOSH) conducted testing on seventeen Burrell Cans in 1995, during development of the support where the ratio of the height to the diameter, or the aspect ratio, was between 2:1 and 4:1. Based on the results of that testing, it was suggested that the standard aspect ratio of the Can be less than 5:1. This suggestion is intended to preserve the overall stability of the Can, which will help to maintain the initial stiffness and prevent load shedding. Recently, the necessity of the aspect ratio has been questioned, and this issue will be addressed in this paper. Since the initial development and introduction, more than 130 tests of the Can have been conducted at the NIOSH Mine Roof Simulator (MRS), and 25 of those specimens had aspect ratios greater than 5:1. The 18-in-diameter by 10-ft-tall specimens had the largest aspect ratio, 6.67:1.However, the aspect ratio is not the only parameter that affects the performance characteristics of the Can. Multiple factors, such as the use of different wood species, the use of different header or footer configurations, and the use of pedestals, as well as biaxial loading conditions can also decrease the stiffness and capacity of the Can. Data from full-scale tests that include these other factors are analyzed to show that the initial stiffness is primarily affected by the roof and floor contact configurations. Furthermore, load shedding is more likely to occur or begin earlier when the aspect ratio is greater than 5:1 and one or more of the other factors are present.

Jan 1, 2012

By Sir Stopford Brunton

Gold was first found in Nova Scotia about 1830-40, but its significance at that time was not appreciated. Probably the first discovery that resulted in any work was made by Lieut. C. !'Estrange, at Mooseland, on the Tangier river, in 1858.1 Since that time gold has been mined with varying success until now, and from 1868 onwards work has never altogether ceased. Gold mining in Nova Scotia is at the moment under a cloud, and the idea generally accepted by most people is that it has failed in the past, and that there is no prospect for it in the future. The actual reasons for the present situation have never been carefully analysed, and it seems a good thing to see what really is the state of the case and whether or not this general idea is worthy of credence. It is the purpose of the present paper to analyse the situation in the light of present knowledge, and to set forth some data which may assist in the future development of the Province.

Jan 1, 1926

By Rob D. Morrision, Paul W. Cleary

"The best accepted method for design of autogenous and semi-autogenous mills is to carry out pilot scale test work using a 1.8 m diameter by 0.6 m long pilot scale test mill. The load in such a mill typically contains 250,000-450,000 particles larger than 6 mm, allowing correct representation of more than 90% of the charge. This scale of DEM model is now within the practical range of standard workstations running an efficient DEM code.This paper describes various ways of extracting collision data from the DEM model and translating it into breakage and wear estimates. Account is taken of the different breakage mechanisms (impact and abrasion) and of the specific impact histories of the particles in order to assess the breakage rates for various size fractions in the mills. These impact histories have the potential to be directly related to breakage as they most resemble the single particle breakage tests which are used by the JKMRC to calibrate more traditional population balance models for variations in ore behaviour. However, the specific impact histories also show a background of many low energy collision events within the mill. This Background may constitute what is usually regarded as “abrasion” breakage. As might be expected, high impact events are concentrated in the toe of the charge and near to the mill shell where the forces associated with the load bearing on each particle is more concentrated."

Jan 1, 2003

By Stephen Chung, Graham Mustoe, Joe Haid

In an open cast coal mining operation, a 305 m (1000 ft) long by 49 m (160 ft) thick overburden cast blast can produce more than a million cubic yards of broken muck that needs to be removed before the coal recovery process can start. In the Powder River Basin of Wyoming, it is common to see 30 to 40 percent of the overburden cast to a spoil that does not require rehandling with heavy equipment. Therefore, the higher the percent cast, the better the cast blast is rated. However, depending on the shape of the muck profile, there is often 20 to 30 percent of the muck standing in front of the high-wall. This portion of muck would require a number of dozers to push down to the dragline pad level. From the mine operator point of view, it is believed that for a given muck profile, there should be an efficient dozer pushing method such that a dragline pad can be developed in the shortest time. As a tool for analyzing this dynamic problem, a 2-D discrete element model, i-PushTM, has been developed to simulate a dozer pushing operation. This mechanistic model takes into account the dozer blade geometry, the dozer operating procedure (e.g. cut-depth, blade fill distance, forward and reverse speeds at specific slope angles), material density and cohesion. To demonstrate how i-PushTM can be used to help determine the most productive push routine, this paper presents three dozer push methods to compare the effectiveness of pushing at 3:1, 4:1 and 5:1 push angles.

Jan 1, 2006

By C. L. Glorioso

As an introduction and credentials for our talk, let me take a moment to introduce you to Wimpey Worldwide and specifically to Wimpey Minerals, USA, Inc.

Jan 1, 1995

By Delio Amorim

Industry 4.0 concepts is the new biggest challenge on the industry nowadays and every company in every industry in every part of the globe is looking to implement this somehow on their factories and machines. To do that on the newest long rolling mills, that brings already onboard state-of-the-art technologies, is for sure a challenge of machinery builder industry, but how to become the long rolling mills built on 70’s, 80’s or 90’s part of this innovation process and connected to the new trends? This is the main mission here, to show some examples of applications that goes in this direction.

Oct 1, 2019

By John J. Sammarco

The U.S. Bureau of Mines seeks to increase safety and efficiency in U.S. coal mines. One approach is to develop technology for automation of a continuous mining machine. Realization of an autonomous mining machine requires development of subsystems for machine intelligence, navigation-positioning, and computer control. This report focuses on investigation of one subsystem, an onboard heading system, which would be responsible for determining and controlling machine heading. The onboard heading system investigated is a multisensor system to determine machine heading, pitch, and roll. A directional gyroscope provides heading (yaw), fluxgate sensors provide a compass heading, and gravity-referenced clinometers give machine pitch and roll. The system utilizes a dedicated microcontroller networked to an external system of computers. Tram commands, supplied to the network from external computers, are executed by the onboard system. Sensor feedback is employed for closed-loop control of machine heading by controlling pivots and turns. The report discusses operating limitations and error sources of system sensors and presents test results of closed-loop control of machine heading. Results of tests with a mining machine are used to exhibit various sensor shortcomings and to evaluate control of pivots and turns.

Jan 1, 1990

By R. R. Seeber

(Pittsburg Meeting, March, 1910.) IN the copper-mining district of northern Michigan a fair-sized mine usually operates two or more shafts along the strike of the lode, these shafts being usually at least 1,000 ft. apart. The tonnage to be hoisted from each shaft is large-from 13,000 to 25,000 tons per month. The hoisting-engines used are generally steam-driven, non-condensing, duplex engines with Corliss valves, supplied by steam from separate boiler-plants where the distance between shafts is great. In an attempt to centralize power-plants and secure central-station economies, the Winona Copper Co. installed an electric hoist of the Ilgner type, with Ward Leonard control. A brief description of this plant has already been published.1 The only point of variation from the simple Ilgner set lies in the connection of two generators to a single induction-motor by flexible couplings. These generators serve motors which operate hoisting-drums at separate shafts, viz., No. 4 shaft, Winona, and No. 1 shaft, King Philip. , The hoist for No. 4 shaft, is about 1,700 ft. from the power-plant, and in this building the motor-generator set is placed. No. 1 King Philip hoist is 1,500 ft. from the motor-generator set. The equipment of the motor-generator set is as follows: In the middle of the set is a 12-pole, 450-h-p., 600-rev. per min., 2,080-volt, three-phase, 60-cycle, variable-speed induction-motor, connected on each side to a 20-ton fly-wheel which is 10 ft. in diameter, and to a 6-pole, 170-kw, 575-volt, interpole, direct-current generator. On each side of the shaft is placed a separate exciter, which delivers current at 125 volts. The lubrication of the four main bearings that support the fly-wheels * Presented also, by mutual agreement, at the meeting of the American Institute of Electrical Engineers, New York, N. Y., Mar. 11, 1910. Engineering and Mining Journal, vol. lxxxviii., No. 3, p. 110 (July 17, 1909).

Sep 1, 1910

By Raja V. Rarnani, Robert L. Frantz

"The more than 75 research projects funded throughout the first 10 years of the Dust Center's operation have resulted in numerous cumulative findings fulfilling the goals of the Center. These project descriptions present the methodologies and project-to-project relationships leading to their various accomplishments and demonstrate the mesh between project objectives and Center goals.To develop equipment for collecting respirable dust samples.To develop experimental methods for particle-by-particle characterization of morphology, size, and chemistry.To develop experimental methods for overall respirable dust sample characterization of size distribution, chemistry, and crystallography.The project directly addresses the Center's goals to enhance the understanding of the scientific and engineering characteristics of fine and respirable mineral particles found in mining and milling atmospheres and to establish the relationship between natural and cultural factors (mine geology, mineralogy, mining and milling methods, equipment, and control measures) in the generation of fine particles. The project also aims to contribute to the development of control mechanisms for reducing ambient respirable dust concentrations and worker exposures.The work on this project is related to similar work on Coal Mine Dust Characterization (Project No. 2701/MN1) and Characterization of Dust Particles (Project No. 4203/PS3).Airborne dust sampling was performed at the following locations: 1) a sand and gravel quarry in Southern New Hampshire, 2) a welding facility, 3) a ceramic powder facility, 4) a metal powder facility, and 5) the air in Cambridge, Massachusetts. A portable sampling box incorporating two Sierra personal cascade impactors was designed and produced. At a 2-LPM flow rate, the effective cut-off diameters of the Sierra impactors were 10.0, 6.0, 3.5, 2.0, 0.9, and 0.5 mm, respectively, for each stage, and the air passed through a PVC filter after the last stage. In addition, the sampling box contained a total respirable dust filter. The substrates were weighed carefully before and after collection, and the weight increases were recorded. All films, foils, and filters were put in the balance chamber for more than 8 hours to stabilize the temperature and humidity before weighing. A Cash 21 microbalance (±0.001 mg) was used to weigh the Mylar films, SS films, and filters."

Jan 1, 1995

By B. J. Moore

This Bureau of Mines publication estimates that U.S. helium resources as of January 1977 were 710 billion cubic feet. These resources are broken down into four classifications, as follows: Helium in measured natural gas resources and in storage, 201 billion cubic feet; helium in indicated natural gas resources, 150 billion cubic feet; helium in hypothetical natural gas resources, 175 billion cubic feet; and helium in speculative natural gas resources, 184 billion cubic feet.2 Most of the helium in natural gas is presently dissipated as natural gas is consumed as fuel and for other purposes. Helium resources of the United States may also be divided into three other categories: (1) Depleting and undiscovered natural gas resources, 589 billion cubic feet; (2) nondepleting natural gas, 83 billion cubic feet; and (3) storage, 38 billion cubic feet, of which 37 billion cubic feet is federally owned and 1 billion cubic feet is privately owned. The United States does not have any significant leasehold rights in the depleting fuel gas resources. However, through the Department of the Interior, it does have leasehold rights to about 70 percent of the helium found in nondepleting natural gas, and it owns over 90 percent of the helium in storage.

Jan 1, 1979

By R Cooksey

The Globe-Progress Mine is an open pit gold mine that is part of the larger Reefton Goldfields deposit located on the West Coast of New Zealand. The regional geology comprises a series of north to south oriented fold structures that have undergone post-deformation mineralisation. The structural geology within the mine itself is more complex, with major shears hosting numerous high-grade mineralised quartz shoots and splays that have been historically mined.The selective mining of ore within the pit is challenging due to the orientations of the hanging wall and footwall areas of the main Globe shear zone, the lithologies of these areas which range from highly brecciated and sheared material to competent mineralised host rock, and in the hazards presented by the numerous old historic underground workings. The coordination of drilling, modelling and excavation of the ore requires careful planning to maximise recovery whilst operating with the pit design boundaries.Grade control packages are custom designed to reflect the orientation of the footwall and hanging wall mineralisation. The shear material in the footwall zone dips between 60° and 70° and requires angled drilling whereas the footwall mineralisation is contained in shallow dipping quartz veins sub parallel to bedding and can be vertically drilled to best intercept the mineralisation. Ore excavation is directed so that the contact between the footwall and hanging wall is mined in the correct direction so that any non-visual ore contacts can be safely mined and that the ore-waste dilution is reduced.The ongoing grade control and selective mining of the Globe Progress deposit continues to deliver high grade ore for processing by ensuring that waste and dilution of ore is reduced and that recovery is maximised.

Aug 22, 2011

By Stephen C. Tadolini, Robert Hawker, Peter Mills, Colin Grubb, Tom Meikle

"In unfavorable strata conditions, it is often necessary to install additional long tendon support as part of a primary support cycle. Although these support systems provide the required additional stability to the roadway installation does have a significant effect on the rate of development. To overcome the slow cure time of Portland cement-type grouts, the use of two component resin systems, such as polyurethanes and urea silicates, have become favorable. However, concerns over low modulus and creep properties has led to the development of a two-component grouting medium that displays the properties of traditional cable grouting materials with the rapid reaction times of pumpable resin systems. This paper describes product testing, application, surface trials, underground trials, and full-scale applications of the Tekthix System in a dynamic underground environment. INTRODUCTION Single-component cement grouts have been used to anchor long tendon supports for many years. They range from high- to low-slump Portland cement and can be slow-setting to fast-setting grouts. However, current cement grouting systems, which includes the grout and equipment, have some disadvantages: 1. Low-slump grouts require pumps that can handle a thick, high-viscosity grout, so choice of pumps is limited. 2. Pumping distance is limited with current cable bolt grout pumps; operators often tend to add water to allow pumping long distance, which adversely impacts the quality and strength of the material. 3. Fast-setting grouts tend to cause issues with pump and line blockages due to the reduced working life of these single-component materials."

Jan 1, 2017

Recovery of Tantalum Capacitors from Waste Printed Circuit Boards Using a Pneumatic Separator

Sep 13, 2010

By D. McCarthy

Contract is a PC-based software program designed to satisfy the main features that have been identified to be lacking from cost estimation systems currently in place in the Australian coal industry. Contract was developed in conjunction with an Australian contracting company to refine the existing core structure used by the company for project evaluation. The key feature of Contract is the availability of analysis functions to explore multiple options within a contract project by altering identified variables. The ability to update project files has been incorporated into Contract to ensure that it is user-friendly and relatively simple to use. Lists of mining equipment and consumables are stored in MS ACCESS database files, along with the supplier details for each item. Each time a project is initiated there is a dynamic link to the database files and the most recent current information is retrieved and linked with the project. Contract provides an option to calculate the changes in metre unit cost as a function of the average development cost. Keywords: Contracting, cost estimation, sensitivity analysis.

Jan 1, 2003

The prospect of utilisation of phosphate ores which contain high P2O5 values associated with Al and Fe has produced a great deal of interest over many years. Processing options have generally been based on the utilisation of by-products which were required to offset the processing costs.   This paper presents a range of processing options which have been investigated at laboratory or technical scale on phosphate ores which predominantly consist of crandallite, CaAl3(PO4)2(OH)5.3H2O and millisite, Ca(NaK)Al6(PO4)4(OH)9.3H2O. Christmas Island (Indian Ocean) and Mt Weld (Western Australia) phosphate ores are good examples of such feedstocks. It is expected that these processes may also be applicable to such phosphate ores from other locations.

Jan 1, 1990

By R. A. Bergman, C. A. Pickles, J. M. Toguri

"Black calcium cyanide is utilized mainly as a reagent for gold extraction. It is produced by reacting calcium cyanamide, sodium chloride and calcium carbide at temperatures in the range of 1200°C to 1400°C in a smothered arc furnace. The equivalent sodium cyanide content of the product is in the range of 45% to 50% and the calcium cyanamide conversion efficiency is in the range of 90% to 95%. Since black cyanide contains impurities such as salt and lime and also because the conversion efficiencies are below 100%, the product contains unwanted materials which significantly increase the shipping costs.The impurity content of the raw materials can not be lowered without increasing their cost and/or the processes to produce them, and therefore the present research was focussed on studying those factors which affect the cyanide grade. The major variables investigated were: the heating rate, the reaction temperature, the salt to cyanamide ratio, the nitrogen content of the calcium cyanamide, moisture additions and calcium carbide additions. It was found that each of these variables had a significant effect on the product grade. The highest cyanide content of the product was obtained for salt to cyanamide mass ratios of 0.55 to 0.60. The salt reduces the decomposition rate of the cyanide and, therefore, at low salt to cyanamide ratios and at higher temperatures, the product grade is decreased. It is likely that the salt evaporates at the higher reaction temperatures and this decreases the cyanide capacity of the melt. High heating rates minimize the residence time and thus salt evaporation is reduced and higher grades can be obtained. As expected, the cyanide content increased with the nitrogen content of the cyanamide. Calcium carbide additions resulted in an increase in the product grade. The presence of small amounts of moisture in the charge caused a significant decrease in the cyanide content of the black cyanide. An equilibrium reaction is postulated in order to explain the black cyanide process and in particular the effect of calcium carbide on the product grade."

Jan 1, 2002