Search Documents

By Michael J. Friedel

As part of an investigation aimed at mitigating the hazards caused by abandoned mine openings, the Bureau of Mines conducted a series of electromagnetic surveys in the Galena, KS, area of the Tri-State mining district. The application of monostatic ground-penetrating radar (OPR) and inductive electromagnetic methods for detecting and delineating hazardous mine openings and attendant features was demonstrated to be feasible for shallow mine workings (i.e., less than 35 ft) occurring below flat-lying areas. Accurate determinations of depth to a mine roof appeared to be limited to roughly 20 ft using the GPR method. Features such as mine voids, fractures, and zones of subsidence were located beneath the Mainstreet (State Highway 26) site using the GPR system. Both the GPR and inductive electromagnetic techniques satisfactorily located mine openings and pillars at the Hell's Half Acre site. Geophysical interpretations were supported by exploratory drilling and mine maps.

Jan 1, 1990

By Dana T. Updyke

An evaluation was made of one of several improved underground communication systems sponsored by the U.S. Bureau of Mines. The system evaluated was installed in a typical metal/non-metal room and pillar mine and utilized UHF repeaters connected to a unique distributed antenna and passive reflector system which provided mine-wide communications. A microprocessor controlled data collection system was assembled and installed for the evaluation. Data consisting principally or times and durations of messages and identities of the originating transceivers was collected between February and August of 1982 (6 mos.). Analysis of the data shows that the principal benefits are reduction in time required for unscheduled maintenance and repair, enhancement of safety, and better coordination of production activities. A cost benefit analysis shows a net benefit over cost, although it is also concluded that the capacity of the system is greater than can be justified by current activity in the mine.

Jan 1, 1983

By Cade Mweemba, Alex Mwanza, Jackson Sikamo

"The Zambian Copper mining industry as we know it today has its genesis from early in the 20th century in the 1920s. Consistent private sector-driven investment in the industry over a period of over 50 years in exploration, mine development and operation, development of minerals processing facilities, building of infrastructure for pyrometallurgical and hydrometallurgical processing, with attendant support facilities, including building of whole new towns, resulted in copper production going from zero to a peak of 769 000 tons of copper in 1969. At the same time, the industry created jobs to the extent that in 1972 the industry had over 62 000 direct jobs. The industry was nationalized in 1973 and remained in government hands for just over 24 years. During this period, the industry experienced a serious decline in production levels, reaching the lowest level at the dawn of the 21st century in the year 2000 when production was 250 000 tons. In terms of jobs, an average of just under 2000 jobs were lost every year in the 24-year period, reaching just over 22 000 direct jobs in 2000. Following the return of Zambian politics to pluralism and liberalized economic policies, the government decided to privatize the mining industry. The process started in 1996 and by the year 2000 all the mining assets had been privatized. The new investors embarked on serious investment to upgrade the assets and to develop greenfield mining projects. Fourteen years later and investments of over USD 12 billion, the industry production levels increased year- on-year to reach a peak of 763 000 tons in 2013 with direct jobs reaching 90 000. This paper discusses the impact of the mining industry in Zambia on the economy in areas such as employment, support to other industries, direct contribution to the national gross domestic product (GDP), foreign exchange earnings and social amenities. The paper also focuses on the performance of the mines during these periods vis-à-vis mineral availability, mineral grades and complexity, new technologies and human capital. This is looked at particularly in the light of current challenges the industry is facing and makes suggestions on how the industry can be nurtured to continue being a major driver for the Zambian economy and a major player in the international copper mining business."

Jan 1, 2015

By Richard D. Hagni

The character of phosphorous-bearing minerals in the Birmingham red Iron ores and iron-bearing minerals in the Eufaula bauxite deposits in Alabama has been Intensively studied by petrographic, ore microscopic, luminescent microscopic, scanning electron microscopic, electron microprobe, and x-ray diffraction techniques. A total of 15 types of phosphorous-bearing mineral grains have been recognized in Birmingham iron ores by their characteristic sizes, shapes, and distributions. Size measurements, modal analyses, and texture analyses have permitted an estimate of potential liberation of phosphorous from the iron ores by beneficiation to be 27% In areas of previous mining and 60% in areas of current iron reserves. Fine grinding, selective flocculation, and flotation may constitute the best beneficiation technique for future research. Hematite and goethite are the most important iron minerals in Eufaula ferruginous bauxites, but pyrite, marcasite, and siderite are Important iron minerals in some varieties of ferruginous bauxite, and lepidocrocite and ilmenite occur locally in minor quantities. Although simple screening will remove the coarsest iron-bearing grains, research on the utilization of high gradient magnetic separation to reduce the amounts of iron-bearing grains is recommended.

Jan 1, 1981

Air pollution control regulation$ already implemented or being considered for implementation require substantial investment of capital to remove the sulfur oxides from copper, lead, and zinc smelter gases. There will be an attendant increase in production costs and possibly an associated increase in the price of these metals to the consumer. The total investment and any resultant metal price increase will depend upon the control regulations that ultimately will be adopted by the individual States. Controversy has arisen between the metals industry and governmental control agencies regarding the status of stack gas desulfurization technology and the ability of industry to control sulfur oxide emissions to the degree proposed by some of the more stringent regulations currently under consideration. This paper evaluates the problems involved in achieving various degrees of control over smelter sulfur oxide emissions and the technology available to accomplish the task of assuring clean air. The estimated cost of compliance is reviewed for the copper, zinc, and lead industries, but principal at tent ion is given to the copper situation.

Jan 1, 1971

By S. H. Badenhorst

Zacharias Lewala discovered a diamond at Grasplatz, near Lüderitz in April 1908. While this stone may not have been the first diamond to be found in this barren, inhospitable area, it most certainly was the stone that set off a chain reaction ultimately leading to the creation of Namdeb as we know it today. [ ]

Jan 1, 2003

TIMBER supports for large underground cavities are temporary expedients until the permanent filling can be put in. Nevertheless, timber supports are very necessary in some form. The general problem is to support the cavity in all directions withthe minimum of timber, disposed in the strongest way. The simplest way of filling an irregular space with timber sets is to form triangles.The right-angled isosceles triangle (Fig. 1) leads to the true square set, in which caps are equal to struts. The right-angled unequal-sided triangle and the scalene isosceles triangle (Fig. 2) lead to the oblong square set, where caps are longer than struts.The scalene triangle (Fig. 4) leads to the rhombic or oblique set. The equilateral triangle leads to the hexagon set (Fig. 3), in which the caps and struts are all equal. These five plane figures, the triangle, square, rectangle, rhomb and hexagon, are the only figures that will completely fill any irregular plane figure, without interstices. Hexagon sets were first suggested by the writer in 1902 to a mine manager at Broken Hill, who did not see his way to use them.

Jan 1, 1912

By Rudolf E. Grauer

[ ]

Jan 1, 1981

By E. Barnard

Tarkwa Gold Mine is located in south western Ghana, and is majority owned and operated by Gold Fields Ghana Limited. The Tarkwa CIL plant utilises a single low aspect 27' x 42' 14MW dual pinion drive SAG mill designed to mill 4.2mtpa (525tph). The plant was designed and constructed in a manner that would facilitate its expansion to 8.4mtpa (1,050tph). Since the plant was commissioned in September 2004, the SAG mill has consistently exceeded its nameplate throughput by up to 25%. Through the installation of a 26? x 36? 14MW dual pinion drive Ball mill along with additional upstream and downstream equipment, the plant will now be expanded to 12mtpa (1,500tph). This paper endeavours to outline the process and engineering design challenges along with the future construction challenges of the expansion in the midst of a fully operational plant.

Jan 1, 2008

By P. A. Beck, M. V. Nevitt

All binary and a number of ternary u alloys formed by first long period transition elements were examined and found to be ferromagnetic at low temperatures. The Curie temperatures for these alloys were measured. It was found that the correlation of the Curie temperature with composition may be described qualitatively in terms of the contributions of the various component atomic moments to the saturation moment of the alloy. Ternary Fe-Cr-Mo u phase alloys were also found to be ferromagnetic, with a Curie temperature dependent on the iron content and largely independent of the unit cell dimensions. Similar relations were found for the Co-Fe-Cr and the Co-Cr-Mo a alloys, where the Co + Fe content appears to determine the Curie temperature. RECENTLY, it has become increasingly evident that the u phase is some kind of an "electron compound." Several papers1-' discussed the empirical correlation between the composition of the various u phases in alloys of the transition elements and the distribution of electrons in the partially filled d-levels of the component atoms. However, a picture of the latter can be formed only in a more or less intuitive manner, as in the Pauling theory," and the rigorous treatment of these problems is at present prevented by lack of adequate knowledge of the electronic structure of the transition elements in the metallic state. It appeared reasonable to expect that investigation of the magnetic properties, which are related to d-shell electrons, may help in clarifying the physical nature of the foregoing empirical correlation. Qualitative tests of samples of various compositions have shown that certain u alloys become ferromagnetic at liquid nitrogen temperature." The present investigation was undertaken to determine whether or not low temperature ferromagnetism is characteristic of a large variety of u alloys and to establish how the Curie temperatures of ferromagnetic u alloys are influenced by changes in composition and in lattice parameter. In the first portion of the in- vestigation, Curie temperatures were measured for a series of u alloys containing either vanadium or chromium with one or two of the elements manganese, iron, cobalt, or nickel. In the second phase of the work, data were obtained on the Curie temperature of ternary (Fe, Co, Cr)a, (Fe, Cr, Mo)a, and (Co, Cr, MO)U alloys, as a function of composition and of interatomic spacing. Experimental Procedures High frequency vacuum melting in high purity re-crystallized alumina crucibles was employed in the preparation of the u alloys, using metals whose lot analyses are given in Table I. Approximately two-thirds of the alloys were analyzed chemically, the analytical results being in acceptable agreement with the intended compositions, as seen in Tables I1 and 111. The specimens were annealed for homogen-ization in an atmosphere of purified 92 pct He and 8 pct H, mixture or in evacuated and sealed Vycor tubes at temperatures from 780" to 1300°C, depending on the temperature range of the u phase field for the particular composition. The annealing temwerature and time for kach alloy are given in Tables 11 and 111. Curie points were determined by an induction method; the change with temperature of mutual inductance between two coils was observed when the i-u specimen was inserted into the flux path between the coils. The transformer consisted of three coils each containing 1200 turns of 0.0050 in. diam enameled copper wire. The center coil, P in Fig. 1, served as the primary coil, and was linked magnetically with each of the two secondary coils, S, and S? which were connected in series opposition. The primary coil, P, was energized by an audio-oscillator, set at a frequency of 500 cycles per sec, while the signal from the transformer secondary circuit,

Jan 1, 1956

By W. P. Haynes

ESTIMATED United States crude-oil production during 1943 established a new annual peak of 1,500,000,000 barrels, a daily average of 4,118,000 barrels. This would be an increase of 315,000 barrels per day, or 8 per cent over 1942 and 7 per cent over 1941, the previous peak. During the first ten months of the year, production jumped from 3,782,000 barrels per day in January to 4,400,000 in October. Available data for the last two months of the year indicate a leveling off of this trend, with daily rates slightly above 4,400,000 barrels.

Jan 1, 1944

By Linda Duncan, Trevor Yeomans, Chris Potorieko, Michael Fullam

"NVI Mining’s Myra Falls Operation is a 4,000 mtpd copper/zinc flotation circuit with by product gold of ~28,000 ounces per year. Gold recovery has historically averaged 40-55%, however, a portion of this was recovered in the zinc concentrate and received poor payment. Two Knelson CD-30 Concentrators have been operating in the grinding circuit since 1992, with gravity recovery averaging about 2-5% over that time period.The Myra Falls gravity circuit was one of the very first hard rock mining installations operating in the world with automated Knelsons. The mine has employed a unique and unusual upgrading method for the Knelson concentrate that had never been evaluated as to its efficiency. Recent Gravity Recoverable Gold Testing by McGill University, and mathematical modelling of the Gravity Circuit by Knelson Gravity Solutions indicated the gravity circuit was not living up to its potential. Myra Falls Personnel changed the upgrade system-operating regime, and a complete gravity audit of the grinding circuit was carried out, with the results confirming the initial suspicions. Gravity recovery increased from 5% to 15%, with overall gold recovery improving by 5%.INTRODUCTIONNVI Mining operates a 4000 tpd mine and mill complex on Vancouver Island. The milling circuit consists of open circuit rod milling, closed circuit ball milling, gravity recovery, copper flotation, zinc flotation, and tails disposal. There are two milling circuits, “A” circuit, and “B” circuit."

Jan 1, 2006

By John W. Mentz

Phase I study efforts addressed: 1) acid mine drainage formation theory; 2) effects of inundation in reducing acid mine drainage formation; 3) summary information on the types of acid abatement technology currently available and the problems inherent in each; 4) analysis of two potential means of partially inundating abandoned segments of active underground mines to reduce acid formation. This subsequent Phase II Draft Final Report addresses all of the above, but concentrates on and defines Item 4. Seal construction techniques were taken through five logical steps as follows: A) Location Analysis; B) Coal Barrier Pillar Analysis: C) Ground Water Analysis; D) Design Considerations: E) Economic Analysis. The design details of both low wall dams and section seals were discussed in a series of segments: a) Case Histories; b) Feasibility Analysis; and c) Design (including representative calculations). Study efforts showed that both concepts are feasible only in certain mines where the geologic-hydrologic physical makeup is suitable to contain a mine pool. Low wall dams in particular were found to have extremely limited applicability as a means of pollution reduction. Section seals, while clearly dependent upon site specific conditions, have a some what broader range of utility and are more effective in pollution reduction. The proven dramatic reduction in acid mine drainage attributable to inundation makes this a concept that must be considered.

Jan 1, 1981

By H. K. Taylor

Ore reserves are inadequately defined. Geological reconnaissance and pre-feasibility mining work generate a broad range of valid tonnage estimates, many published for the benefit of various interests, who may view all figures as reserves. This work reviews the regular estimation of tonnages, grades and relevant factors for single deposits. A consistent framework of definition is suggested which, by conforming to the known structures of feasibility studies and long-range plans, avoids the pitfalls of over-categorisation and of unrealistic promises. Applications are based on North American experience but are intended for general use

Sep 1, 1991

By Lloyd L. Farnham

This paper is one of a series describing the mineral resources of the Nation, including location, history, production, ownership, geologic setting, and mining methods for most of the known manganese deposits in New Mexico, With few exceptions these descriptions are the result of field examinations by the writer. Of 32 counties, the 12 which occupy the western half of the State contain all the known manganese deposits, These counties are Catron, Dona Ana, Grant, Hidalgo, Luna, Rio Arriba, Sandoval, Santa Fe, Sierra, Socorro, San Juan, and Taos. (See fig. 1.)

Jan 1, 1961

By Peter R. Drummond

THE paper consists of four sections: (1) a discussion of early work; (2) presentation of the results of a chemical investigation of Falcon-bridge nickel-copper blast-furnace matte; (3) application of the results of this investigation to mattes in general; and ( 4) a summary of conclusions. All general discussion will be confined to the fundamental system of ferrous-cuprous sulphides (FeS-Cu2S). Nickel-, lead-, and zinc-bearing mattes will be treated as minor varieties of the parent system. DISCUSSION OF EARLY INVESTIGATIONS Matte investigations may be divided into three classes: first, those treating the sulphides as alloys-theoretical studies of the system FeS-Cu2S, such as those of Hofman (ll)t or Carpenter and Hayward (2); second, chemical research on mattes made under smelter conditions, such as that carried out by Hawley (3) or Avetision ( 4); third, combinations of the . above, such as the investigations of Gibb and Philp (5) or Fulton and Goodner (6). Much research in the first of these classes, including determinations of . freezing points and of data for structure-composition diagrams of the system FeS-Cu2S, was carried out in the period 1890-1910. LeChatelier and Ziegler (1, 13) proved that FeS, when heated alone above its melting point, dissociated in part, and Friedrich ( quoted by Fulton, 6) showed the same for Cu2S. The reactions may be expressed by the following equations: [xFeS yFe + yS (volatilized)+ (x -y)FeS xCu2S )'Cu+ yS ( vohtilized) + (x -)')Cu,S ] Sulphur is lost by volatilization, leaving a melt of metallic iron plus ferrous sulphide in the one case, and of metallic copper plus cuprous sulphide in the other. If the mixed sulphides are heated far above their melting points, there results either an iron-rich matte containing Fe-FeS-Cu2S or a copper-rich matte containing FeS-Cu2S3-Cu, depending on the relative amounts of each sulphide in the mixture.

Jan 1, 1940

A new horizontal borehole packer for use in coal beds has been developed. This packer utilizes a principal of operation which has not previously been used. The resulting packer is less costly to purchase, can be easily repaired in the field with inexpensive expendable parts. This report describes the development and testing of the new packer and the evaluation of commercially available packers.

Jan 1, 1971

Copper mineralization associated with minor molybdenum, silver, and gold occurs in a hydrothermally altered brecda within a granodiorite mass of Upper Permian age. A dyke system of rhyolite, dacite, and andesite forms plug-like bulges near the breccia and probably caused mineralization as a late stage effect.Base metal sulphides occur as disseminations, fracture and cavity fillings in the breccia. A pyritic halo in hydrothermally altered granodiorite surrounds the breccia and grades into unaltered granodiorite. Drilling during 1969 indicated the grade is subeconomic.

Jan 1, 1972

By Raymond P. Miller

This two volume report addresses slope stability of surface mine spoils within the Interior Coal Province. Sixteen (16) mines were visited, pertinent data and samples collected, and reported spoil instabilities back-analyzed. Laboratory test results are compared to back-analyzed material properties. Available methods of slope stability analysis are reviewed and evaluated with respect to application to mine spoil stability evaluation and prediction. Correlation and tentative relationships among spoil material properties, highwall conditions, mining equipment and procedures and empirical observations are presented. Slope stability sensitivity plots illustrate the relative significance of various input parameters on stability. Slope stability input parameters are correlated with site and mining conditions to identify the primary factors controlling spoil stability. Investigative methods, spoil stability enhancement techniques, spoil stability prediction procedures and future study areas are discussed. Appendices include a glossary of terms, annotated bibliography, details of mine visits, and detailed laboratory test procedures and results.

Jan 1, 1979

By Kennedy G. L, Evans D. G

The development of the carbonization of brown coal briquettes to produce a hard char suitable for use in place of imported hard coke has continued in Victoria, and an experimental carbonization plant has recently been commissioned at Morwell by the Gas and Fuel Corpora.tion to assess the prospects for the commercial production and marketing of hard char in Victoria. The char offers advantages in its very low ash content and its uniform lump size, while the indications are that it could be marketed at a price competitive with that of imported hard coke. The hard char is unique amongst metallurgical fuels in combining a high reactivity with high physical strength, and research by the University of Melbourne into its utilization in foundry cupolas for melting iron has shown how modifications could be made to take advantage of these properties. An 18 inch experimental cupola has been built to test in practice the predictions made from this fundamental research.INTRODUCTIONSteady development has continued in Victoria from the promising laboratory researches at the University of Melbourne which were reported to the 1955 Annual Conference of The Institute (Worner, 1956). This work had shown that a hard lump char could be produced by the high temperature carbonization of standard industrial briquettes by careful control of the heating conditions, and that the special briquetting techniques adopted in Germany were unnecessary with Yallourn brown coal. Continuation of this research has led to the refinement of carbonization techniques and has increased the strength of the char until it has equalled that of conventional metallurgical cokes.

Jan 1, 1960