Search Documents

By I. W. Farmer

High horizontal stresses and high horizontal to vertical in-situ principal stress ratios in the plane of underground drifts and entries can damage weakly laminated roof rocks quite severely. Such stresses are difficult to measure accurately, as illustrated by case histories of in-situ stress measurement at Wistow and Lea Hall mines, in the UK. Their direction and relative magnitude can, however, be estimated from the absolute velocity vectors of continental plates. With the preliminary results from the World Stress Map project now available it is possible to indicate mining areas where regional horizontal stresses are low, such as Europe, and high, such as Australia and Asia

Jun 19, 1905

In September 2003, a test was conducted to see if a115-mm- (4.5-in.-) diam Mocap Vari-Stem blasthole plug could improve the pattern of explosives using different top stemming material. The test took place at the J.S. Faulkroad and Sonsstone quarry in McCalisterville, PA. The test consisted of a production stone blast. Half of the holes were stemmed with standard crushed stone. Two-thirds of the remaining half were stemmed with Vari-Stem plugs and crushed stone. And the remaining one-third of the second 50 percent was stemmed with Vari-Stem plugs and only drill cuttings.

Jan 1, 2004

By B. W. Gandrud

[The Bureau of Mines is conducting an extensive investigation of coal preparation in the Alabama coal fields in cooperation with the University of Alabama and coal-mine operators. In this investigation the drainage characteristics of typical coals from the Warrior and Cahaba n fields were studied. Tire main purposes of this study has been to evaluate no nearly as possible relative influences of certain factors on rate of drainage and to determine whether the drainage characteristics of coals from different beds or from different mines on the soma bed differ materially. A further objective was the development of a laboratory drainage test that would predict approximately the rate at which any coal will drain after having been loaded into a railroad car in a saturated condition. The study has been confined to samples of slack coals - that is, coals from which none of the fine sizes have been removed. The samples ranged in upper size limits from 7/16 inch to 3 inches. It did not seem necessary to study nut and egg sizes, that is, sizes from which the fine coal has been removed by screening, as these lose water so rapidly by natural drainage that they present no serious problem in dewatering after treatment in a washer. The significance of drainage characteristics of Alabama coals is apparent in view of the fact that not less than 70 percent of Alabama?s total coal product is subjected to wet washing before being materials.]

Jan 1, 1941

By W. W. Weller

Thermodynamic values for scandium and its compounds are very sparse. This is evident upon examination of any of the commonly used compilations of thermodynamic data. For example, National Bureau of Standards Circular 5004 lists only four heat of formation values, two free energy of formation values, and four heat-capacity values for scandium compounds. The entropy of crystalline scandium is one of the most fundamental values that has been lacking. This Bureau of Mines paper reports heat-capacity data for scandium metal in the temperature range from 50° to 298° K., together with the entropy value at 298.15° K. derived from these data through application of the third law of thermodynamics.

Jan 1, 1962

By H. E. Hawkes, D. A. Barr

Time variations in the copper content of the sediments of streams draining mineralized areas were studied in two areas of contrasting climatic environment, one in northern and one in southern British Columbia. In each area, samples were collected and observations made of rainfall, stream discharge and air and water temperature at intervals throughout the summer season. Samples were analyzed for total and cold-extractable copper. Results showed a weak inverse relation between cold-extractable copper and discharge in two out of the three test sites in the southern area, and a decrease in ratio of COld-extractable to total copper over the duration of the test period at a highly anomalous site in the northern area. In suspended rock flour resulting from glacial erosion of mineralized rock in the northern area, virtually all the copper was found to be soluble in cold, dilute hydrochloric acid. None of the variations observed is sufficient to cause serious problems in geochemical sediment surveys. Systematic collection and trace analysis of stream sediments has seen wide application in recent years as a method of primary prospecting in primitive areas. Common practice is to collect fine-grained samples of sediment either from the active channel or from the flood plain near the channel. Samples are dried, sieved and the -80-mesh fraction analyzed after breakdown of the sample by a relatively strong attack, such as by fusion or by treatment with hot perchloric acid. Drying, sieving and rigorous chemical attack requires established facilities, either in a well equipped central laboratory or in base camp. Thus analysis for total metal involves a substantial delay from the time the samples are collected until the analytical data can be reported. An alternative system uses a cold aqueous extrac-tant in place of the hot acid or flux.4 Advantages of the cold-extraction techniques are that kits can be prepared for use directly at the sample site and that, in some problems, the patterns in cold-extractable metal, usually abbreviated cxMe, are more useful as ore guides than the patterns in total metal.' In the course of operational geochemical sediment surveys, a problem that has come up repeatedly is failure to reproduce anomalous values or patterns by resampling the same areas. The mystery of the vanishing anomaly has led to speculation as to whether there is a significant variation in the metal content of sediment samples with the weather or with the time of year. Review of the published literature shows that a number of experiments have been carried out on time variations in the metal content of stream water.1,2,5,7-9 The only published report on time variations in stream sediments that has come to the authors' attention, however, is by Govett,3 working in Northern Rhodesia.

Jan 1, 1963

By Dale S. Preece, J Paul Tidman, Stephen H. Chung

A discrete element computer program named DMC-BLAST (Distinct Motion code) has been under development since. 1987 for modeling rock blasting (Preece & Taylor, 1989). This program employs explicit time integration and uses spherical or cylindrical elements that are represented as circles in two dimensions (2-D). DMC-BLAST calculations compare favorably with data from actual bench blasts (Preece et al, 1993).

Jan 1, 1998

By N. Kanari

Chalcopyrite concentrates and their pure constituents were chlorinated by C12+N2 between 25 °C and 750 °C. The reaction products were analyzed by SEM, XRD and chemical analysis. The effect of gas flow rate and chlorine content of the gas mixture on the reaction rate were investigated. At room temperature, these solids start to react with chlorine giving metal and sulfur chlorides. Complete reaction is achieved at about 300 °C and the iron and sulfur chlorides were fully volatilized. The chlorination residue is composed of valuable metals' chlorides. A simplified flow - sheet for the treatment of chalcopyrite concentrates by chlorine was suggested.

Jan 1, 1998

he Wyalong goldfields were discovered in September, 1893, Messrs. Neeld and Sons, owners of the principal mine, being the pioneer prospectors. During the earliest days of the field the ore was sent to Barmedman, a distance of eighteen miles, for treatment at a battery there. The field rapidly increased in importance, and it was not long before a public battery was established on the spot. After some considerable quantity of ore was treated by this process, it became apparent that battery treatment was quite unsuitable for the richer ores, involving, as it did, considerable loss in the tailings. Recognition of this fact led to the erection, in 1895, of plants by the Wyalong Chlorination and Cyanide Works, owned by Mr. Walter Sully, for treatment by their processes; followed, at a later date, by Messrs. Neeld and Sons Chlorination Works. The Wyalong Chlorination and Cyanide Works, after a delay of twelve months in the erection of their plants, have since catered continuously up to the present time for the requirements of the field.Their plant consists of a No. 3 Gates' rock·breaker, a revolving dryer, a No. 5 Krupp mill, revolving roasting furnace with finishing hearth, two chlorination vats of 20 tons capacity each, "nine cyanide vats of 30 to 100 tons capacity, two Wheeler pans and three chlorine generators. The ores are purchased outright on assay at a fixed scale of charges, and treated by the owner of the works on his own account.

Jan 1, 1903

By R. S. Lang, C. C. Merrill

The recovery of zinc from oxidized zinc minerals by the caustic soda leach and electrolytic or chemical precipitation was investigated . With the exception of willemite ( 2 ZnO • Si0₂ ) oxidized zinc minerals were readily soluble in 180 to 240 g / 1 NaOH solutions . A high- grade zinc flake was recovered electrolytically from solutions which had been treated with zinc powder to precipitate copper and lead . Solutions were recycled to the leach stage with a recovery of about 85 percent of the zinc from an ore containing 21.2 percent zinc . Electrolysis was conducted at a current density of 120 amp / ft2 with a power consumption of about 1.5 kwhr /lb zinc . Zinc was also recovered from leach solutions by dilution of the solutions , carbonation of the solution , or the addition of sulfur to boiling solutions . A dilution ratio of 5 : 1 precipitated 59 percent of the zinc in 9 days . Carbonation of the solutions precipitated the zinc as zinc oxide ( ZnO ) and solutions could be recausticized for recycling . Zinc precipitated as the sulfide with sulfur was easily filtered and washed . Approximately half of the sulfur added to solutions was lost in the form of sodium thiosulfate ( Na S₂03 ) .

Jan 1, 1965

Author's Note: Since the paper on "All-Flotation at North Broken Hill Limited" was read and discussed, the metallurgical results obtained have conclusively justified the adoption of the All-Flotation treatment.At present the shipping grades of lead concentrate produced from North mine ore range between 74% and 75% Pb, carrying approximately 43 oz. Ag and 4.5%-5% Zn. The lead recovery in lead concentrate is recording 95%-96% of the lead content of crude ore, and the milling and treatment cost on 6400 tons crude ore perweek of 96 hours has dropped to 6s. 3.6d. per ton on ore. With an increased ore tonnage, and with a new mill, considerable further reduction in costs is certain.New flotation machines, with 30 in. vertical depth of overflow (instead of 42 in. depth), are now being tried for the secondary granular treatment, with advantageous results. The treatment to-day is practically the same as that outlined in the paper, excepting that additional concentrate is returned for retreatment in the existing units.(Signed) A. LOWRY.Mr. T. A. READ: The author states (page 356 of Proceedings, No. 79), "The sulphide ore itself was then comparatively coarsegrained, a fact which permitted ready concentration of the galena contents by means of jigs, tables, vanners, etc."

Jan 1, 1931

By R Durchholz, A-J Heiertz, R Schmitz

Mining of lignite is the largest bulk materials handling activity in Europe. In order to mine this lignite, with an average calorific value of only a third of bituminous coal in an economical way, highly efficient opencast mining technology is mandatory. The total continuous mining of overburden and lignite was introduced more than 60 years ago and was subsequently developed stepwise into the largest mass transport system of the world. In 2011, the Inden Mine, one of three RWE Power mines, stripped 90 Mbcm of overburden to produce 22 Mt of lignite. In total, nearly 100 Mt of Lignite was produced from the three mines of RWE Power in Germany. Beside bucket wheel excavators (BWE), several high-performance in-pit crushing and conveying (IPCC) systems, which allow the adoption of continuous mining systems, even for typical shovel and truck (S&T) operations, are available today. RWE Power assists operators considering a change from the S&T to IPCC technology, both in the planning process involving large-scale belt conveyor systems and later with operational know how transfer. In a number of cases, the challenges associated with this system change have been addressed and solved successfully. One key challenge is managing the development of skills for operating the belt conveyor systems efficiently. This paper compares the effectiveness of S&T to different configurations of continuous mining operation for an up to 170 m deep mine with a total annual output of 117 Mbcm. From the mine operatorÆs point-of-view, the quantity and skill level of staffing required for operation and maintenance are discussed in detail. The main conclusion of this paper is the larger the operation becomes and the longer the mine life is, the earlier fully continuous mining systems should be planned and implemented.CITATION:Schmitz, R, Durchholz, R and Heiertz, A-J, 2012. Change challenges for large open pit mines, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 103-110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By H Jones

Closure cost estimates may be generated at any stage of a mining operationÆs life; commencing with the initial prefeasibility studies and continuing through to the final decommissioning cost estimates. However, not all mine closure cost estimates are necessarily the same. Cost estimates will vary depending on the purpose for which they are prepared, the organisations requiring or undertaking the estimate and the stage of the mining operation. Different organisations can legitimately arrive at disparate cost estimates for closing the same mine because the organisations have different reasons for requiring the estimates. Another, equally valid, reason for potentially wide variations in cost estimates by different organisations on the same mine site is the different definitions of æclosure costsÆ used by different estimators. This paper considers the different approaches by different organisations including operating companies, government authorities and financial organisations and uses a hypothetical example based on practical experience to illustrate some of these differences in estimation methods.The paper suggest that a more consistent approach to closure cost estimating in the Australian mining industry would assist mining companies, governments, the accounting industry and the broader community to better understand this complex component of mine planning. One possible approach to closure cost estimating is briefly outlined.CITATION:Jones, H, 2012. Closure cost estimation - All things to all men?, in Proceedings International Mine Management 2012, pp 115-124 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By H. Miller

In recognition of the need for a portable low-profile hard rock crusher, the Bureau of Mines sponsored the development of such a unit capable of moving up as the face advances. By allowing primary ore reduction at or near the mine face, the advantages of conveyor haulage From the face as demonstrated in soft ore and coal mines, could be realized for hard rock Brines as well. This report presents the results of a development and testing program for such a portable low-profile crusher, designed by Eagle Crusher Company and called the M44. The unit has an extremely low vertical profile considering its size and capacity. The crushing jaws, which form the crushing lumber, are inclined, with the lower jaw mounted for eccentric movement relative to the stationary upper jaw. This provides efficient crushing while also forcing material through the crushing chamber. As a result, the inlet feeder can be disposed horizontally. To facilitate correct processing of different materials, the size of the discharge opening and the action of the movable crushing jaw are variable. The unit also incorporates a feeder hopper and discharge conveyor that provides for efficient ore handling through the machine. Tests demonstrated the M44 Crusher's high capacity, efficiency and reliability. During testing, it crushed over 120,000 tons of materials of up to 32,000 psi compressive strength at production rates in the 200-350 tons/hour range. The unit operated smoothly under simulated low-headroom conditions, and Proved readily transportable.

Jan 1, 1983

By Ashley P, Neale T

Alluvial gold was discovered on Sudest Island in 1888, and by 1893, an official production of 10 000 oz had been won by expatriate miners from shallow alluvial and colluvial workings. Hardrock sources were located and while one was developed at Mt Adelaide, production is unknown. Sudest Island comprises mostly phyllites and lesser coarse grained rocks which are cut by metamorphic quartz veins and basic (locally shoshonitic) intrusives. Sheared and altered basalts and serpent- inites represent are believed to be elements of an ophiolitic suite inferred to be associated with metamorphic core complex development and thus similar to tectonic environments on Misima and the D'Entrec- asteaux Islands. No epithermal-style quartz suggestive of a target similar to that on Misima Island has been identified on Sudest. A hardrock source for the alluvial and colluvial gold is interpreted to be metamorphic quartz veins similar to those in the Bendigo- Ballarat Zone of central Victoria, possibly remobilising gold derived from the meta- sedimentary and meta-igneous rock pile. The present focus is on development of a small scale alluvial gold mining operation in conjunction with exploration for hardrock targets. This latter programme remains at a reconnaissance stage.

Jan 1, 1991

By H. Cho

There is an indication that high-pressure roller milling promotes selective liberation due to preferential breakage along the mineral boundaries. A study was undertaken to compare the degree of liberation obtained by high-pressure roller milling with that of conventional ball milling. Coals with different HGI's were ground in a high-pressure roller mill and a ball mill to produce products with similar size distributions. The products were then subjected to float-sink separations to determine the degree of liberation. Also, the relative cleanabilities were compared by separating the ground products by froth flotation. The results from this study are presented in the paper.

Jan 1, 1994

By Ivan F. Avery

DOMESTIC production of carbon black increased 4 percent in 1962 to 2,056 million pounds. Furnace black output was 8 percent, or 132 million pounds, above that in 1961 and accounted for 90 percent of total carbon black production. Channel black output continued to decline and was 55 million pounds less than in 1961. Carbon black shipments during the year totaled 2,082 million pounds and were 5 percent above those of 1961. About one-fifth of these shipments were exported; the balance were sold domestically. An increase of 180 million pounds in domestic sales was partially offset by a decline of 80 million pounds in exports. Total value of carbon black production in 1962 was $145 million. The average value per pound of 7.06 cents was 0.24 cent per pound less than in 1961. Producers' stocks declined 26 million pounds during the year.

Jan 1, 1963

By P. Kiruthika, A. Murali Krishna

Soil liquefaction is a dangerous phenomenon that involves huge damages during strong earthquake ground motion event. Stone columns (SCs) are widely used as liquefaction mitigation element which is expected to perform the improvements against liquefaction hazard by densifying, increasing the stiffness and rapid dissipation of excess pore water pressure in the surrounding soil. Although in the recent times few studies on the behaviour of stone columns in the seismic zone has evolved, the performance of SCs in the multi-layered soils is not extensively examined. This paper presents the numerical investigations on the performance of SCs installed in the multi-layered soils as a liquefaction mitigation measure against the seismic loading. The acceleration time histories, Excess Porewater Pressure (EPP), vertical displacement and stress ratio evaluated along different depths using PLAXIS 2D. With the installation of stone column there is a considerable reduction in the acceleration amplitude, which in turn reduces the EPP and vertical displacement at different locations and the amplitude of reduction depends on the soil stiffness levels at the depth.

Sep 1, 2022

By Harry Perry

Although the markets for coal in the United States have changed rapidly over the last three decades, the uses of coal, namely, to produce heat and power or coke have been left almost unchanged. The coke is used either as a chemical reducing agent alone or as a reducing agent and source of heat. Most of the heat and power markets for coal require no coal processing, although for more than 50 years, many proposals to skim the more valuable substances in coal before burning have been advanced. Thus, the only large tonnage market requiring processing of coal is high-temperature carbonization to make coke. At present, coal requires processing for some small markets, but for future potential large markets, such as gasification, conversion to liquid and gaseous fuels, and conversion to chemicals, coals will require more processing than is now being done.

Jan 1, 1962

By Gordon T. Clark, James R. Struthers, Celal Kirandag

INTRODUCTION Project Background The Washington State Department of Transportation (WSDOT) hired the Seattle office of Parsons Brinckerhoff to lead a team of consultants to produce an Environ-mental Impact Study and perform conceptual and preliminary engineering. The pur-pose of the Alaskan Way Viaduct and Seawall Replacement project is to replace the existing earthquake damaged and aging viaduct and sea wall, adjacent the downtown waterfront of Elliott Bay, with structures that have improved earthquake resistance and that maintain or improve mobility and accessibility for people and goods along the existing corridor. With an estimated replacement cost over $4 Billion and construction duration exceeding 8 years, it is one of the largest transportation design projects on the West Coast of the United States today. Seattle, Washington is a city of over 2 mil-lion people in the Northwest corner of the United States. Ever since the Klondike Gold Rush in 1897, Seattle has been considered a departure point to Alaska. Because of this, the street along the waterfront was named the Alaskan Way in 1930. Alaskan Way Viaduct and Seawall The Alaskan Way Viaduct (AWV) carries State Route 99 along the shoreline of Elliott Bay through downtown Seattle and is a vital part of Seattle’s highway system. The viaduct carries approximately 110,000 vehicles per day or 25% of all north-south traffic through Seattle (Figure 1). It is 3.4 km (2.1 mile) long with 3 lanes in each direction and was constructed of cast-in-place reinforced concrete between 1952 and 1956. The wear and tear of daily traffic, salty marine air, and several earthquakes have taken their toll on the facility. Studies in the mid-1990s provided early evidence that the viaduct was nearing the end of its useful life. The viaduct’s increasing age and vulnerability was apparent by crumbling and cracking concrete, exposed rebar, weakening column connections and deteriorating railings. In early 2001, a team of structural design and seismic experts began work to determine whether it was feasible and cost-effective to strengthen the viaduct by retro-fitting it. In the midst of this investigation, a 6.8 magnitude earthquake shook the Puget Sound region (the Nisqually Earthquake, located 56 km (35 miles) from Seattle and deep below the surface) caused moderate damage to the reinforced concrete structure. WSDOT closed the viaduct for inspection and repairs intermittently for several days over a period of several months.

Jan 1, 2007

By David A. Lipton

U.S. Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine the mineral resources and potential of the Moses and Dennison Peak RARE II areas in Tulare County, California. These areas, along the west slope of the Sierra Nevada, are underlain by grarnitic rocks of the Sierra Nevada batholith and contain numerous metasedimentary roof pendants. Silver, copper, and zinc occur in contact-metasomatic deposits within the metasedimentary rocks. In the Moses area, the Powell Mine (fig. 1) contains an estimated 90,000 tons (82,000 t) of subeconomic silver, zinc, and copper resources. The King Solomon Prospect has 3,000 tons (2,700 t) of silicified phyllite containing zinc. On the Helen-Joyce Prospect, 44,000 tons (40,000 t) of gossan occur above a poorly exposed silver-zinc rich zone. Potential exists for additional mineral resources and occurrences at each of these properties.

Jan 1, 1983