Search Documents

By Minoru Yamada, Eikichi Mohri

INTRODUCTION Most of the copper concentrates treated by the flash smelting furnace at Kosaka smelter come from "black ore" that is produced in the local mines nearby. The copper concentrates contain various impurities such as lead and zinc as shown below. [ ] These impurities are mainly concentrated into the flue dusts in the copper smelting system. The dust production rates of flash smelting furnace and converter at Kosaka smelter are, therefore, fairly high compared with other copper smelters. However, by recovering these valuable metals in the dusts systematically, profit-increase of the by-products must be expected. This also leads to the solution of environmental pollution problems and enables us to establish the technical completion of complex sulfide ore treatment by flash smelting process. HISTORY OF DUST TWATMENT AT KOSAKA SMELTER 1) December in 1967 to January in' 1969 Since the flash smelting furnace started its operation in December 1967, all the dusts from the furnace had been recycled. Only conver-

Jan 1, 1976

By John W. King, S. Ralph Austin

Spurred by recent forecasts of greatly increased demands for uranium by 1980 and beyond, interest is once again focusing on America's western uranium deposits. One of the principal producers in this area is the Gas Hills district in Wyoming, the site of approximately 12% of the known uranium in the U.S., including past production and current reserves. Located on the south flank of the Wind River Basin, the Gas Hills deposits have been recently studied by the Atomic Energy commission for clues to and guides for discovering similar-occurring ores. The ore deposits are confined to a permeable sandstone unit, up to 350 ft thick, at or near the base of the upper Wind River formation of early Eocene age. The uranium occurs in three principal north- south "ore trends," each of which is about six miles long, one mile wide, and separated from each other by approximately three miles (Fig. 1).

Jan 5, 1966

A LARGE proportion of the steel that is melted and refined in the United States and poured into ingots is made in basic open- hearth furnaces. The capacity of these furnaces varies over a wide range with a large majority falling within limits of 50 to 200 tons (Fig. 1) The two general types of furnace design used are stationary [ ] and tilting furnaces, the former being much more common. The fuel burned in such furnaces is either one of several types of gas, or a liquid fuel such as oil or tar, or a combination of gas and liquid fuel. GENERAL FEATURES OF FURNACE CONSTRUCTION The design of a modern stationary furnace built to burn liquid fuel and with a capacity of 175 tons is shown in Figs. 2 to 4. The cross- section of the furnace at the tap hole is illustrated in Fig. 2, which shows the bottom construction, sloping back wall, and the rigid steel

Jan 1, 1944

By C. Wert, D. Keefer

The results of this study indicate that sudden increases in aging temperature lead to reversion phenmena in carbon in the a, iron system. These phenomena are thought to be associated with the dissolution of carbide precipitates. Reversion is studied with respect to three variables: 1) Specimen grain size, 2) the initial amount of carbon in solution, and 3) difference between initial and final aging temperature. It is found that of these variables the initial carbon concentration has the greatest effect on reversion. THE solid solution of carbon in n iron has been the subject of numerous investigations throughout the past few years. Despite the great amount of effort which has been put forth toward understanding this system, however, there persist a number of interesting aspects of the system which are open to further research' Studies Of the precipitate which forms as a result of aging a supersaturated solution of carbon in a, iron appear to be particularly interesting. The present work is an attempt to determine certain

Jan 1, 1960

By M. L. Brashears

IN the last 15 years industrial use of ground water has more than doubled, and in 1951 amounted to 5 billion gallons per day. A similar sharp increase in the utilization of ground water for irrigation and public-water supply occurred in the same period. In many areas rapid increase in withdrawal from wells has taken place almost entirely unhampered by regulatory control and with little or no integration of effort. As might be expected, the chief interest in many regions has been maximum production rather than sustained perennial yield. As a result, widespread depletion of underground reservoirs and deterioration of the quality of the water stored in them has taken place in many areas, even though total pumpage in the United States is far below ultimate potential. Of even more concern is the fact that excessive withdrawal has drawn salt water into the reservoirs beneath many heavily populated centers along the Atlantic, Gulf, and Pacific coasts, causing costly abandonment of pumping plants.1

Jan 10, 1953

By R. P. Smith

THE carbon content of iron-silicon and of iron-manganese alloys at fixed activities of carbon has been reported previously.' It seemed desirable to investigate a system which allows a more extended range of alloy composition within a single phase region. The iron-nickel system is ideal in this respect, in that all alloys from 100 pct Fe to 100 pct Ni are face centered cubic ("austenitic") at 1000 °C. The experimental procedure was similar to that previously described.1,2 The alloys, in the form of pieces about 2 by 2 by 0.2 cm thick, together with a similar specimen of pure iron, were equilibrated with each of a series carbon monoxide-carbon dioxide tnixtures of fixed composition, quenched in the carburizing gas in the top of the furnace and then analyzed for carbon. The carbon content of samples containing more than 0.3 wt pct C was determined by the usual combustion method; those with less carbon

Jan 1, 1961

By M. W. Cox, V. F. Hollister

Exploration for metallic mineral deposits is carried on by those special adaptations of methods which the explorer believes will yield most economically or satisfactorily the particular answer sought. In this project the usual methods of geologic observation, recording, and interpretation, when combined with magnetic geophysical methods and geochemical soil sampling, led to disclosures of appreciable zinc mineralization where none was visible in surface exposure. Since 1945 considerable work has been done with geochemical prospecting methods, chiefly in determining the presence and distribution of various elements existing in minor amounts in rocks, soil, vegetation or waters of mineralized areas. Such work, in which the U. S. Geological Survey has taken the lead, finds a ready place in the field repertoire of the exploration geologist as a supplement, not a substitute, for other methods. The Chollet project was carried out in 1951 by the American Smelting & Refining Co. near its Van Stone mine in northern Stevens County, Wash., in the area shown in Fig. 1

Oct 1, 1955

By Rudolph G. Wuerker

With stepped-up work in rock mechanics, more and more data on strength and elastic properties of rocks has become available. Results of measurements of tensile strength, in addition to determinations of compressive strength, allow us to deter- mine, even if only in an approximate way, the third property influencing failure of a brittle material: shear strength. It is fairly generally agreed upon in rock mechanics, in drilling and blasting research, that Mohr's theory provides an acceptable method for explaining the failure of a brittle material. Mohr states that a material may fail either 1) through plastic slip when shearing stress Y in the planes of slips has reached a limiting value (which in general depends on the normal stress, X, acting normal to the surface), or 2) when the largest normal tensile stress has reached a limiting value. The mode of failure depends upon which of the two stresses is the smaller.

Jan 10, 1959

By Joseph Hartshorne

Ever since the introduction of the Siemens regenerative furnace, it has been recognized that a certain amount of gas is lost each time the furnace-action is reversed. This loss comes, first, from the gas which passes through the free connection between the stack and the gas-main, which exists during the time the reversing-valve is turning over; and, secondly, from the gas which is in the chamber and flues, from the hearth to the reversing-valve, and which flows back into the stack when the valve is reversed. The amount lost each time is, of course, small; but, since a furnace is reversed from four to six times every hour for, say, 300 days in the year, the aggregate is large enough to be well worth attention. The estimate has been published1 that, in Germany aloue, the loss from the first of the above causes amounts to 500,000 barks per year. The loss from the second cause is, of course, much greater.

Jan 1, 1907

By J. C. Konopka, S. A. G. Poppen, E. K. Roesner

Many shafts have experienced stability problems during shaft sinking because the designer failed to fully appreciate the conditions he would encounter. Some shafts have failed during construction because the ground supports provided to compensate for the expected conditions were inadequate despite the most careful investigations and analyses. To design a ground support which is ultimately safe to achieve stability during shaft sinking would be too costly and impractical and, therefore, many shafts would simply not be constructed. The design of a ground support for shaft sinking based on an intimate understanding of the expected ground behaviour and stress development during excavation combines the art of mining with the science of geotechnical engineering. Where no historical design data is available, the designer of the ground support must: 1. classify the rocks and soils and assess their behavioural characteristics; 2. calculate the primary and secondary stresses; 3. design and/or select a ground support system which will ensure stability of the excavation during shaft sinking.

Jan 1, 1983

By E. S. Noe, D. S. Arnold, C. E. Polson

Reactors of today and tomorrow require a high uniformity of their fuel elements despite the wide variety of uranium raw materials from the far corners of the earth. To meet these quality standards metallurgists have been working to design production methods capable of yielding reactor feed materials whose maximum impurities are specified in parts per million, whose physical limits are expressed in thousands of an inch, and whose density variations are less than 1 pct. Such requirements are necessary to maintain normal neutron flow in the atomic reactor and to insure that the isotopic content of the feed material is maintained within narrow limits. Uranium ores and concentrates are produced in many sections of the world, including the Belgian Congo, South Africa, Australia, Canada, and the Colorado Plateau of the U. S. Ores from many of the larger deposits are relatively low grade, and these are concentrated near the mine site before shipment to refining centers, but high grade ores may be shipped directly to refineries.

Jun 1, 1956

By Robert Mehl

IT has been shown that quenched iron of high purity exhibits a Widmanstätten figure much resembling martensite in appearance.1 This figure exhibits a maximum of four directions of the surface traces that characterize it, suggesting that a Fe forms from y Fe in plates parallel to the {111}, octahedral, planes in the y lattice. Because of this, and also because of the general similarity to the structural appearance of martensite and to the Widmanstätten figure obtaining in slowly cooled hypoeutectoid steels it has been suggested2 that the orientation relation-ships obtaining between the y and a phases in pure iron are identical with those demonstrated in martensite3 and in slowly cooled hypoeutectoid steels,4 and indeed that the crystallographic mechanism of formation of a Fe from y Fe is the basic mechanism determining the orientation relation-ships found in both martensite and in slowly cooled hypoeutectoid steels. This paper will present experimental evidence in support of this view.

Jan 1, 1934

Discussion of the paper of Robert Franke, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 79, July, 1913, pp. 1201 to 1205. ARTHUR 0. GATES, Lafayette, Ind. (communication to the Secretary*) :-In connection with the comparison of mechanical crushing efficiencies in Tables I and II of Mr. Franke's paper, I wish to suggest a somewhat simpler way of making this' comparison, based upon what the writer has called the "crushing-surface diagram," as published by him in the Engineering and Mining Journal for May 24, 1913. Such a diagram, based on the data given in Table II, is submitted herewith, Fig. 1, cumulative percentages being plotted as abscissas and reciprocals of diameters (theoretical mesh per inch). plotted as ordinates.. Such a diagram averages the diameters without calculation, and areas upon it are proportional to surface produced, and, in accordance with Rittinger's law, to energy spent on crushing alone.

Jan 11, 1913

By D. G. Westlake

THE structure observed in thin foils by transmission electron microscopy is not necessarily representative of the initial bulk material. We have shown that hydrogen, originally present in a specimen of vanadium, niobium, or tantalum, can be concentrated by the thinning operation used to prepare foils from the bulk materials.' These foils exhibited domain walls indicative of a tetragonal distortion of the bcc unit cells, probably caused by ordering of the hydrogen in preferred interstitial sites. We believe this ordering does not occur at room temperature in the bulk material which contains less than 1 at. pct H. In a continued effort to prepare metal foils whose hydrogen concentrations remain constant during preparation, we have developed some new chemical and electrothinning techniques for vanadium. Each of the procedures presented in Table I produced foils that were thin enough for transmission electron microscopy. The experiments described below were performed to test the effect of each thinning procedure on hydro-

Jan 1, 1968

By N. H. Parker, J. G. Papailias, G. Gutzeit

In its many forms, the turbine has greater latitude of application than any other mixing device. It is readily adaptable to all tank shapes, from the shallow pan to the tall and narrow stovepipe. Although turbine mixers can be adapted to most tank conformations, experience has shown that there is a preferred shape for optimum efficiency in each service. In the accompanying drawings this relationship is illustrated by the shallower tank for slurry suspension. The taller tank is preferable for continuous staged systems, or maximum retention of the gas phase in absorption. No single turbine covers the entire range of these applications with maximum efficiency. The back-sloped blade offers maximum power economy. The straight blade develops a higher discharge velocity for the dispersion type of service requiring localized shear. The same high shear environment is provided by the back-sloped impeller with stator ring assembly, which permits the most positive discharge control, Fig. 1. Positive stream control is critical in solids suspensions.

Mar 1, 1956

By A. Thies, A. Mezcer

The Haile mine is situated in Lancaster county, South Carolina, twenty miles south of Lancaster. The topography of the country is characterized by low hills rising generally less than two hundred feet above the many small creeks which traverse the surface. The road from Kershaw, the nearest railroad station, 3 1/2 miles from the mines, leads through woods with sandy soil and cottonfields. In many places it lies on the bare rock and shows that the adjacent covering of soil and earth is usually not more than one foot thick, and often less. This covering is to a great extent sand. Close by a bridge, about one mile from the mine, large round boulders of diabase may be observed. The country-rock seems to be exclusively talcose slate, with a general strike varying from N. 45' E. to N. 70' E. These variations may be seen in the immediate neighborhood of the mines, the large open cuts of which present exposures favorable to such ob-

Jan 1, 1891

By Francisco Cadena

THE construction of Norris Dam, built by the Tennessee Valley Authority on the Clinch River, a tributary of the Tennessee River, involved the production of coarse and fine aggregate for approximately 1,000,000 cu. yd. of concrete. A hammer-mill plant for the manufacture of sand from quarried rock was indicated as the most economical method of providing this material. The abrasive character of the feed as compared to the average hammer-mill feed made it necessary to control operations rather ciosely, and this resulted in the accumulation of many data bearing on production and maintenance. This paper will deal only with three specific sets of data, accompanied by such general infor-mation as may be necessary to explain the conditions under which they were obtained and followed by discussions on the relation of silica content to hammer wear, comparative costs of slugger and stirrup hammers, and comparative costs of tool-steel and manganese-steel grate bars.

Jan 1, 1937

By Robert G. Woolery, S. Ramachandran, James A. Weber, Donald J. Hansen

Union Carbide began looking seriously at heap leaching in 1971. At that time some 1.6 million tons of mineral averaging 0.40 kg U308 /t) (0.80 lb U308) were stockpiled at various sites around the Gas Hills, Wyoming, uranium facility. Several alternatives for economically exploiting these reserves were considered and heap leaching seemed the most attractive. At the time, Western Nuclear Inc. was operating a heap leaching project nearby in which the low-grade ore was leached with sulfuric acid, the product liquor treated in an on site solvent extraction circuit, and the stripped product liquor re-acidified and recycled. The operators were most generous in allowing us to visit their site and in answering our questions. They were also helpful in discussing the problems associated with heap leaching. Their experience confirmed our belief that it was possible to operate a heap leach profitably on material too low grade for conventional milling.

Jan 3, 1978

By D. C. Seidel, E. F. Fitzhugh

Nickel sulfide ores lend themselves readily to concentration before smelting or pressure leaching, but neither of the major oxidized ore types-the iron-rich laterites and magnesium-rich, soft silicates-has been directly concentrated. Upgrading of crude ore in current practice is limited to cobbing lumps of the harder, lower grade rock (protore) from the softer, enriched silicate ore, because only a small percentage of the nickel in these ores occurs in discrete, contrasting mineral particles. There is no apparent mineralogical contrast in the superficial, iron-rich lateritic ores and, in fact, there is no firm assurance that the nickel atoms are within the lattices of the limonite minerals, or else irregularly adsorbed on the limonite. Within underlying, "rotten rock" silicates, occasional veinlets of garnierite and related nickeliferous silicates are found.1 The garnierite veinlets are only incidental, and the majority of the nickel atoms occur as erratic replacements of magnesium atoms in the micaceous chlorites of the ore mass.

Jan 4, 1968

By S. F. Willey

Difficulties encountered in justifying replacements for overage mobile mine equipment at the Gay mine are common to most mining operations. More critical management reviews, resulting from ever rising capital expenses, increased such difficulties. These increased difficulties are especially apparent to those who are primarily operators and are not statisticians, mathematicians or computer men. The Gay mine is located 17 mi east of the town of Fort Hall in southern Idaho. This open pit operation annually supplies the J. R. Simplot Co. and the FMC Corp. with 1.5-2.0 million tons of phosphate ore. Stripping ratios average approximately three bank cubic yards of waste per ton of ore mined. The mobile mine equipment fleet consists of ten 24-cu yd scrapers; twenty-one 30-50-ton end-dump trucks; four 3%-4%- cu yd shovels; fifteen dozers in the D-8 and D-9 classes; and three road patrols. Equipment replacement is based on the results of evaluations made on individual units.

Jan 9, 1972