Search Documents

By F. J. Zuiderweg, G. G. Bemer

Results of a study aimed at assessing kinetics and mechanisms of the batch agglomeration process in suspension are discussed. A recently developed light backscatter technique which enables the increase of average particle size from 1 to 5000 µm to be followed, was used to determine agglomeration kinetics. Growth curves and agglomerate size distributions were obtained in a stirred vessel for various model systems and operating conditions. Four distinct growth regimes were identified, i. e. the flocculation regime, the zero-growth regime, the fast growth regime, and the equilibrium regime. Further, it was observed that large differences in the occurrence and duration of these regimes resulted from small variations in parameters, such as size distribution of the initial particles and the binding-liquid to solid ratio. Mechanisms that determine the occurrence of the relevant regimes are discussed. The growth process was described in terms of population balance equations. In this way, the growth rate, the equilibrium agglomerate size distribution, and the evolution of the agglomerate size distribution were generated. The agreement with experimental results is satisfactory.

Jan 1, 1980

By Howbert Van Dyne

THE Presidio mine of The American Metal Co. of Texas is situated 45 miles south of Marfa, Texas, a town on the Southern Pacific R. R., and lies approximately 20 miles north of the Mexican border. Communication with the railroad is maintained over a state highway. All supplies for mine and mill are hauled in by truck from Marfa and precipitates and concentrates are freighted to the railroad by the same means and shipped to Selby and El Paso, respectively. The mill is at the town of Shafter, 1 mile from the mine and at approximately 350 ft. lower elevation. The ore is conveyed to it by an aerial tramway which requires practically no power on account of the difference in elevation. The mill is a countercurrent decantation cyanide and gravity concentrating plant of 200 tons daily capacity. Coarse and fine crushing are done at the mill. Two near-by shallow wells in the bed of Cibolo Creek furnish an abundance of water. Power is generated for the mill and town by a Diesel engine plant.

Jan 1, 1930

By W. Z. Price

The coal lands that the Nemacolin mine is to develop embrace over 8400 acres; the tract is oblong and its eastern edge is along the Monon-gahela river. As shown in Fig. 1, the mine is divided into two parts (the North mine and the South mine) by a 150-ft. barrier, which however, is cut through at intervals by haulageways. Each part is fed from seven main entries—a loaded track, an empty, a manway, and four return air courses. The loaded tracks converge at the shaft bottom but the empty roads maintain their identity throughout their length. With three intakes and four returns on either side, there is ample room for expansion of air and every facility for ventilating is provided. The four south air courses converge into two, crossing the shaft bottom, and then into one at the south side of the air shaft. The four north air courses converge in a similar manner on the west side of the same shaft. This convergence is accomplished by concrete arched

Jan 1, 1927

Frank 11. Probert, Neudorf, Anhalt, Germany (communication to the Secretary): I have read with much pleasure Mr. Collier's valuable paper. But the system of timbering which he describes as used in the levels, stopes, etc., though it must be admitted to be very strong and safe, seems to me somewhat extravagant. The amount of timber required every month for such a system must be enormous; and only where suitable material could be cheaply obtained would such a plan be economically practicable. The first point which strikes me is the unusually great diameter of the timber employed. In the mines of Pfaffenberg and Meiseberg, which are under my supervision, the country-rock consists of argillaceous slates, traversed by innumerable small fissures or joints, dipping at all angles and striking to all points of the compass. Undoubtedly, this net-work has been caused by the upheaval of granite masses in the vicinity. Each fissure is accompanied by a more or less well-c1efinc.d gouge or fluccan, caused by the rubbing together of the slates at or after the original disturbance. In such

Jan 1, 1900

By D. E. Wolfson, D. A. Reynolds, F. W. Smith

IN 1948 the U. S. Bureau of Mines began a three- phase program to evaluate the extent and quality of U. S. coking coal: 1) a factual appraisal of known recoverable reserves in beds of mineable thickness, 2) a study of preparation characteristics, and 3) a study of carbonization properties. A previous paper presented the methods used in assessing reserves.' Although this investigation is only partly completed, data on coking properties of the Pittsburgh district coals are now available. The results are presented in this article. When coals are selected for manufacture of metallurgical coke more factors must be considered than for any other major use, as no basic industry requires coal of such high quality and uniformity. This is particularly true in the Pittsburgh district, where blast furnace practice is based on use of cokes from high quality coals. Although it is true that inferior coals are carbonized in other industrial areas, both here and abroad, the Pittsburgh coals are the best economically obtainable in the required tonnages, even though they are not the most desirable for metallurgical use.

Jan 3, 1957

By W. N. Page

The Red-Ash colliery was the scene, March 6, 1900, of an explosion by which some fifty men were killed or wounded, and much property was injured or destroyed. On March 19th, the earliest date at which entrance was practicable, I examined the mine with the view of determining the extent, cause and point of origin of the explosion, and with the permission of Mr. F. Howald, the manager, and the owners of the property, for whom the examination was made, I present in this paper some results of that examination, comprising the essential portions of my report to them. Location and Plan of the Mine. The Red-Ash colliery, situated on the south side of New river, next below the Rush Run mine, with which the underground workings are connected, is a drift-mine, the entrance to which is on a slope, about 500 ft. above the river. (Fig. 1 is a plan of the workings, in which the points where human bodies were found are designated by numbers.)

Jan 1, 1901

By T. L. Kesler

With only six small spodumene prospect pits, no detailed mapping, and no subsurface information in 1938, the Carolina lithium-pegmatite area now contains four mines among more than 25 properties on which exploratory work has been done. Even the open pit mine of Foote Mineral Co. described herein, from which ten million tons of ore and waste have been removed since 1952, was virgin ground when mapped in 1938-40 1. It has been a privilege to participate in the transition. In 1940, the spodumene pegmatites were known in a 25-mile belt (originally noted for tin prospecting) between Lincolnton, N. C. and Grover at the South Carolina line. Subsequently, Broadhurst 2 reported relatively small bodies northeast of Lincolnton near the Catawba County line. To the south, diamond drilling done in 1953 on the old Ross tin-mine property near Gaffney yielded pegmatite cores containing a few crystals of spodumene. This fact, not previously reported, suggests that some of the pyroxene in the Ross shaft as described by Sloan 3 may be spodumene.

Jan 9, 1961

By W. O. Hotchkiss

DURING the summer of 1927, the Department of Terrestrial Magnetism of the Carnegie Institution of Washington joined with the Michigan College of Mining and Technology in conducting a series of earth-resistivity measurements in the Michigan copper country. The geological structure in this section is quite varied and fairly well known. The purpose of the investigation was to discover the correlation between the variations in electrical resistivity of large masses of soil and rock in place and the geological structure below the surface. The work done may be roughly divided into two parts: (1) Measurement and study of the variations in resistivity with depth, or with volume, to establish such general relations as exist between the two: and (2) the determination of the specific resistivity of various formations in order to make available more fundamental data which may aid in the interpretation of the results of the former type of measurement. A report by Mr. Rooney, which gives in detail the measurements made and the results obtained, forms the basis for this article.

Jan 1, 1928

By C. H. North, L. E. Lynd, W. W. Anderson, H. Sigurdson

CONSIDERABLE uncertainty is revealed in the literature regarding the nature of the titanium minerals which make up the bulk of the heavy, opaque fractions of numerous beach sand deposits of the world. An investigation was made, therefore, of beach sand concentrates of North Carolina, Florida, Brazil, and India. Magnetic concentration, X-ray, and microscope data were obtained which show that these concentrates consist essentially of ilmenite and its alteration products. The alteration, brought about by oxidation and leaching of iron values, has resulted in upgrading the ores to a range of 56 to 64 pct TiO2, as compared with 52.7 pct in ilmenite of theoretical composition. Conclusions drawn regarding the nature of the dominant titanium-bearing mineral in beach sand deposits have been based mainly on chemical composition, specific gravity, and petrography. This material has usually been referred to as ilmenite or weathered ilmenite. It has also been referred to as arizonite because in chemical composition it resembles an occurrence in Arizona which was described by Palmer1 in 1909.

Jan 8, 1954

By A. F. Baker, E. R. Palowitch, A. W. Deurbrouck

As air-pollution regulations become increasingly more stringent, increased significance is being placed on the amount of sulfur present in coals used for steam generation. These regulations are aimed at minimizing the pollution of the atmosphere with noxious gases such as the sulfur oxides that are formed and emitted when coal is burned. Two meet these future requirements, a definite need exists to reduce the sulfur content of some of the coals used for steam generation. Reducing pyritic sulfur involves liberating the pyrite from the coal and then removing it. The specific gravity of pyrite is high (5.0) compared to that of coal (about 1.2, mineral-free), and standard coal-washing devices, such as wet concentrating tables, will efficiently remove pyrite particles larger than about 100 mesh. Particles below this size will be entrained in the table water and will be carried into the clean coal product. Techniques such as froth flotation are of little benefit for pyrite reduction because the flotation characteristics of pyrite are similar to those of coal.

Jan 6, 1966

By V. T. Stringfield

ONE of the earliest investigations of ground water in Florida was made in 1513 when Ponce de Leon arrived at St. Augustine in search of the Fountain of Youth. The history of the development of the water resources of the State shows that the large artesian reservoir that underlies Florida was discovered in the latter part of the last century. Part of that history is given by L. C. Johnson1 who states that the first successful artesian well in Florida was drilled at St. Augustine between 1880 and 1882. After the City of Jacksonville failed to obtain a flow of artesian water at a depth of nearly 400 ft and abandoned the drilling, R. N. Ellis, City Engineer, and L. C. Johnson, using Johnson's knowledge of the geologic structure of the artesian reservoir, estimated correctly that artesian water could be obtained at a depth of about 500 ft. Thus began the development of the large artesian system in the northeastern part of the State. In 1908, the Florida Geological Survey issued its first report on the ground water of central Florida.

Jan 6, 1951

Equilibrium in Lead Smelting. By S FREDERICK RAVITZ AND KENNETH E FISHER (Tech Pub 681, also Trans , vol 121 2300 words) Four liquids are ordinarily produced in lead smelting, namely, bullion, speiss, matte and slag To determine whether these exist together in equilibrium, the distribution of gold and silver among them was measured To crucibles containing similar mixtures of all four products, varying amounts of silver were added, and the crucibles were heated together under the same conditions for 3 hr, during which the charges melted and separated into four layers After cooling, these layers were assayed for silver, and the distribution coefficients, 1 e , the ratios of the concentration of silver in any particular layer to that in the bullion, were calculated In each experiment, each distribution coefficient was found to be constant, regardless of the amount of silver used Similar results were obtained using gold instead of silver The constancy of the distribution coefficients indicates that the bullion, speiss, matte, and slag exist together in equilibrium

Jan 1, 1937

By Thomas W. Yardley

In many years' experience as a maker and purchaser of cast-iron coated pipe, I have never met with any standard form of specifications for such. Each water-works company, employing a hydraulic engineer, has, under his direction, prepared complete specifications for the particular conditions required; but I cannot find that any two are alike; and each foundry, in bidding for the supply of such pipe, makes the price to cover the conditions' required. I, therefore, have the honor of offering to the Institute a form of specifications for cast-iron coated water-pipe, that may be found useful to water-works companies and others requiring pipe of this kind. The conditions are all reasonable, and can be carried out by makers without additional cost, and with advantage to the purchaser. Section 1 gives the kind of pipe, with its general characteristics. Section 2 specifies that neutral pig-iron shall be used, since such iron possesses the strength required, and is uniform in its shrinkage. Section 5, requiring makers to give the brands of pig-iron used

Jan 1, 1890

By Harry A. Roe

THE power drag scrapers and the slackline cableway excavator have been called "long-range excavators." Broadly, their field of usefulness is restricted to work in which their long range of action permits them to operate economically, and which other, possibly more conventional, excavating units cannot do. Both of these machines dig or lift material and transport it to a remote dumping point. They combine these two functions in a single machine, nearly always in a single straight-line motion. [ ] The purpose of this paper is to examine the important features that distinguish the machines in this group from each other, as well as from other groups. The Machines The "power drag scraper" is a long-range excavating machine that employs a bottomless drag scraper operated back and forth between digging and dumping points by two haulage cables. The typical arrangement is that of Fig. 1. This is the "slusher" of the underground mine, as well as the "dragline scraper" of the sand and gravel industry, and other open-pit mining operations.

Jan 1, 1937

By W. L. Korbee, P. Hazebroek, M. Prats, E. E. Allen, C. A. 225-000-000-017 Verbraak, H. C. van Elst

In a recent paper,' one of us has presented some experimental evidence on the relationship between twinning and brittle fracture in steel. From metallographic examinations of brittle fracture it could be derived that mechanical twins and microcracks are formed already in front of a running brittle fracture. A tentative explanation based on the evaluation of the statistical distribution of mechanical twins vs various angles to the fracture was given in the above mentioned paper. It was suggested that these twins are caused by stress waves emitted by a running brittle fracture. With the aid of high-speed photography and the use of photo-stress sheet we are now able to study in more detail the propagation of a brittle fracture and the emittance of stress waves connected with fracture. A typical example is given in Fig. 1. In this figure a running brittle fracture in an ordinary Thomas steel is shown. The experiment was performed on a Robertson apparatus and the stress waves caused by the fracture were made visible with photo-stress

Jan 1, 1962

By Cyril Stanley Smith

BeTa brass (consisting of approximately equal atomic proportions of copper and zinc) exists as a random solid solution at high temperatures, hut at low temperature< an ordered structure is stable, with the copper and zinc atoms occupying alternate sites on the body-centered-cubic lattice. On cooling, ordering commences at a temperature of 450° to 470°C., depending on the composition. The degree of ordering progressively increases at lower temperatures until it becomes virtually complete at about 100°C. The electrical resistivity of the alloy illustrates the changes clearly (Fig. I). This type of reaction has been a favored subject for study by physicists. An excellent summary of the theory is to be found in a paper by F. C. Nix and W. Shock1ey.l All published data on electrical conductivity, specific heat and other properties agree in indicating that the ordering reaction in beta brass takes place so rapidly that it cannot be prevented or even retarded by quenching&apos; With most ordered alloys, cold-working induces disorder and

Jan 1, 1943

By Luis Toron, Salvador Cortes-Obregon

THE Oaxaca coal fields, shown in Fig. 1, are located in the Alta Mixteca region in the states of Oaxaca, Puebla, and Guerrero. Known out crops are scattered over 3125 square miles. It is probable that further exploration will reveal a more extensive area of deposits. The region is of great importance to Mexico, as at present the only sources of coal are the fields near the U. S. border. Steel mills are also located in the North, and finished products must travel 600 to 800 miles to the area of consumption in central Mexico. The Oaxaca coal, only 120 miles south of Mexico, D.F., lies close to several iron ore deposits. If this coal can be used in steel production is will be possible for the Mexican steel industry to reach new dimensions, commensurate with the growing industry of the central region. Coal can be utilized in thermoelectric plants in this area, which lacks not only petroleum and natural gas but also electric power. It can be used as domestic fuel, replacing charcoal and firewood.

Jan 5, 1954

By Cyril Stanley Smith

BeTa brass (consisting of approximately equal atomic proportions of copper and zinc) exists as a random solid solution at high temperatures, hut at low temperature< an ordered structure is stable, with the copper and zinc atoms occupying alternate sites on the body-centered-cubic lattice. On cooling, ordering commences at a temperature of 450° to 470°C., depending on the composition. The degree of ordering progressively increases at lower temperatures until it becomes virtually complete at about 100°C. The electrical resistivity of the alloy illustrates the changes clearly (Fig. I). This type of reaction has been a favored subject for study by physicists. An excellent summary of the theory is to be found in a paper by F. C. Nix and W. Shock1ey.l All published data on electrical conductivity, specific heat and other properties agree in indicating that the ordering reaction in beta brass takes place so rapidly that it cannot be prevented or even retarded by quenching&apos; With most ordered alloys, cold-working induces disorder and

Jan 1, 1943

I HAVE already described to you many kinds of fusions and fires and still have many to describe if1 am to guide you, as I intend, among the operations of these processes. In all these, quantities of charcoal and various kinds of it must be handled continually and it therefore seems to me necessary to tell something about charcoal for aiding you in these processes. Without it artificers could scarcely bring their works to an end, because it is the food that nourishes the fire both for smelting and for softening the metals, or for calcining or drying things out. [61] It is a very powerful means and not only is its fire used for many more works than other fires, but it is also essential. Although there are many other things that make fire and would make it, I do not know of any that are better adapted for this purpose, or that can be more easily procured in large quantities, than wood and charcoal. For, as you can see, very great forests are found which make one think

Jan 1, 1942

By F. C. Bond

B. H. Bergstrom (Allis-Chalmers Mfg. Co., Milwaukee)—In reading this article, it was difficult to follow through the example given as a starting point in the derivation of the theoretical equation which relates ball size to feed size. A discussion with F. C. Bond led to the following clarification: Bond postulates that "the breaking force exerted by a ball varies ... as the cube of its diameter . . ." and that the force in pounds per square inch required to break a particle varies ... as its diameter squared." He concludes: "It follows that when a l-in. ball breaks a 1-mm particle, a 2-in. ball will break a 4-mm particle, and a 3-in. ball a 9-mm particle." The above example can be true only for a different set of assumptions. Since the first assumption is apparently true, it is the second that must be revised. The second assumption should read that the breaking force required to break a particle varies as its diameter to the 3/2 power. This relationship was derived in the next paragraph of the article.

Jan 1, 1960