Search Documents

By E. T. Turkdogan, L. S. Darken, R. G. Olsson, H. A. Wriedt

Several aspects of the calcination of Michigan limestone were investigated: the rate of calcination of limestone spheres with diameters from 1.8 to 14 cm at temperatures from 800° to 1200°C by a thermogravimetric method; the temperature profile across limestone during calcination; the excess pressure developed in the interior of the stone during calcination; the pore surface area, pore volume, and effective gas diffusivity in burnt lime; and the microstructure of polished and fracture surfaces. It is found that, over a wide range of experimental conditions, the difference between the surface and center temperatures remains essentially unchanged during the latter half of calcination. From the rate of weight loss after about 50% calcination, the value 0.00126 cal per cm sec degree is found for the effective thermal conductivity of burnt lime. From the excess internal pressure measurements, i.e., 0.4 to 6 cm Hg at 800° to 1200°C, the permeability of burnt lime is estimated to be within the range 8 X 10-' to 5 X 10' sq cm. With increasing temperature and time of calcination, the pore structure of burnt lime coarsens as indicated by a decrease in the pore surface area, pore volume, and an increase in the average pore size. For the temperature range 600° to 835°C the ratio (effective gas diffusivity/molecular diffusivity) is about 0.18.

Jan 1, 1974

By J. M. Pilcher

The application of oil to coal for-the reduction of dust has greatly increased the consumers' satisfaction with solid fuels, especially those for domestic use. The combination of oil-treated coal and automatic firing by a small stoker has made possible clean, automatic heating with bituminous coal. This, with the added pressure of competition by other fuels, has caused a rapid development of oil treating practice. A variety of materials derived" from petroleum oils is available from which one may choose for treating a par-ticular coal. Until recently, however, little information had been published to guide the choice. It is most im-portant that the proper type and amount of oil be used in order that all coals marketed as "dustless" will be reason-ably dustless, and thereby maintain a good reputation for oil-treatment. During the past two and one-half years, an investigation of a number of the problems related to the treatment of coal with oil has been conducted at Battelle Memorial Institute. This project was jointly sponsored by Bituminous Coal Research. Inc., Standard Oil Company of New Jersey, Sun Oil Company, and Viking Manufacturing Company. A progress report giving the principal results of the work of the first year was presented before the American Society of Mechanical Engineers in December 1937.1 The present paper is a summary of the entire inves-tigation.

Jan 1, 1939

By George J. Bancroft

It is unnecessary to repeat here the contents of many valuable contributions to this subject which have appeared in the Dansactions and in the publications of the U. S. Geological Survey. As a basis for the further suggestions of this paper, the following are the most important: 1. The investigation of J. R. Don,' showing the gold of certain Australasian veins to have been deposited by ascending solutions, and not by lateral secretion. 2. The theory of Prof. Posepny? distinguishing the vadose from the deep circulation, and ascribing the origin of certain classes of ore-deposits to ascending solutions of the latter class. 3. The theory of Prof. Van Hise,3 as to the underground circulation and the primary enrichment of veins thereby. 4. The paper of Prof. J. F. Kemp,4 showing that ore-deposits are largely the products of " expiring vulcanism." Many. of Prof. Kemp's ideas have been widely adopted by mining men. 5. The theory of secondary enrichment, so lucidly expounded by Mr. S. F. Emmons.V his theory, dealing with the rearrangement of ore-bodies after primary mineralization, has been generally adopted, and seems to me to have been as completely proved as the nature of the case permits. There are two facts which I think should be constantly borne in mind in formulating a theory of the genesis of ore-

Jan 1, 1908

By Persifor Frazer

(Read at the Wilkes-Barre Meeting, May, 1877.) A CLASSIFICATION of natural objects is usually based either upon some fundamental and permanent attribute of the thing itself (as in the case of scientific classifications), or it embraces one or more generalizations convenient for use in ordinary life. Thus, it suffices for the statistician to, know that so many tons of fish are annually taken by our fishermen, and that they realize so many thousands of dollars, whereas to the student of natural history the anatomy, habits, and relationships of the animals are of chief interest, as settling their respective places in the scale of animate nature. Many different classifications of coals have been attempted, as one would naturally anticipate from the immense extent of the coal trade, and the different localities whence the supply was derived. The English divisions were prevalent up to the date of the publication of the last geological survey of the State, except so far as they were modified by local designations. Indeed, Rogers' classifications made very little alteration in the English nomenclature, as may be seen by comparing. the tables given below. To commence with the different kinds mentioned in Ure's Dictionary of Arts, Manufactures and Mines of 1845 " 1. Cubical Coal.-Black, shining, compact, moderately hard and easily frangible. Comes out in rectangular masses, of which the

Jan 1, 1878

By C. R. Austin

IN a recent paper1 the authors presented information on a refinement of the Rohn type of creep test with data on pure iron that exemplified the behavior of the apparatus. The present paper extends that work to nickel and cobalt and to the examination of the comparative high-temperature properties of two widely used commercial alloys. Careful attention has been given to the effect of plastic deformation in decreas-ing creep rate, using the elementary metals iron, nickel and cobalt for purposes of analysis. In any, endeavor to develop new materials for high-temperature service one soon encounters a real problem as to the sort of test to be employed in evaluating the commercial possibilities of the alloys. At one time it was considered satisfactory to determine the tensile strengths at elevated temperatures and to use these values as a criterion for the commercial application of the alloys. More recently the proportional limit has been used as a means of classification. Data obtained from a form of bend test has also shown promise as providing a "merit index" of high-temperature serviceability.2 Koerber and Pomp3 state that since the influence of testing time is small, the high-temperature yield point of steel furnishes sufficiently reliable and concordant values up to about 350° C. (and a maximum of

Jan 1, 1934

By Holbrook Botset

EXPERIMENTS performed in this laboratory on the flow of gas-liquid mixtures through unconsolidated sands have been described and discussed in an earlier paper.4 In these earlier experiments a definite relationship was found between the liquid saturation of a sand and its permeability to the liquid or gas phase. Furthermore, the nature of the sand, the permeabilities of the sands over a range between 17 and 260 darcies, appeared to have a negligible effect upon the saturation-permeability relation. Likewise experiments indicated that the viscosity of the liquid, or the substitution of an immiscible liquid for the gas phase, had only a very slight effect on the permeability-saturation relation. This con-clusion has since been definitely confirmed by the experiments of M. C. Leverett3 on the flow of oil and water through unconsolidated sands. The sands used by Leverett were of very low permeability (between 6.8 and 1.04 darcies), while the oil-water viscosity ratio varied between 90 and 0.057. Since the sands that constitute petroleum reservoirs are largely con-solidated, although of widely varying degrees of consolidation, it was desirable to extend the experiments on gas-liquid mixtures to consolidated sand. In the study of consolidated sands additional variables are involved, but for the initial experiments the only new variable to be intro-duced was the cementing material.

Jan 1, 1939

Long range expansion plans begun in 1966 by The International Nickel Co. of Canada, producer of over 50% of the free world supply of the white metal, are so mammoth as to give rise to the speculation that something might have to burst at the seams. From an annual level of capital expenditure of $35 to $70 million, the company jumped in 1967 to $145 million in new capital investment and will come close to $200 million in 1968. Inco expects to spend $700 million in the next five years, beginning in 1968, for new mines and surface facilities in Canada. The program involves the opening of nine new mines within the next 3 1/2 years, expansion of producing mines, and construction of new plants and modernization and expansion of established ones to process the increased ore production. Beyond this, the company is committed deeply in developing new sources of nickel abroad. Any one of these new projects, if proven economic, would necessitate expenditures of about $100 million or more. For Inco, the economic strain was relieved without a rupture this spring when Henry S. Wingate, company chairman, reported' at the stockholders annual meeting that $150 million had been raised by the sale of bonds. This marked the first time in 32 years that the company had gone into debt.

Jan 10, 1968

By E. I. Larsen, A. S. Doty, F. R. Hensel

The alloy under discussion is a Pig. I shows results of heat-treating tests nickel-silicon bronze and is one of many on two typical nickel-silicon bronze castings age-hardening or precipitation-hardening of the type on which the observations were copper-base alloys. The hardening constituent is a nickel-silicon compound.l The quenching temperature necessary to produce hardening by a subsequent aging treatment is a function of the composition and extends from about 700°C. to 950°C.; the aging temperature range extends from 4000 to 600°C. The work carried out by the authors of this paper was confined to cast alloys having compositions within the ranges of: 1.5 to 3.00 per cent Ni; 0.4 to 0.75 per cent Sj: balance. comer. made. A quenching temperature of 750°C. produces almost as high a hardness on subsequent aging as do quenching temperatures of 850' and 900°C. Several foundries have spent years of active and intelligent effort in trying to control the casting and heat-treating variables of nickel-silicon bronzes and finally gave up the attempts because of the inconsistencies of results.2 This undesirable characteristic was not manifest in the ultimate hardness or conductivity but primarily in tensile strength and ductility, as shown in Table I. The variation in tensile properties was often much greater than that existing on the alloys

Jan 1, 1941

By A. S. Doty, E. I. Larsen, F. R. Hensel

The alloy under discussion is a Pig. I shows results of heat-treating tests nickel-silicon bronze and is one of many on two typical nickel-silicon bronze castings age-hardening or precipitation-hardening of the type on which the observations were copper-base alloys. The hardening constituent is a nickel-silicon compound.l The quenching temperature necessary to produce hardening by a subsequent aging treatment is a function of the composition and extends from about 700°C. to 950°C.; the aging temperature range extends from 4000 to 600°C. The work carried out by the authors of this paper was confined to cast alloys having compositions within the ranges of: 1.5 to 3.00 per cent Ni; 0.4 to 0.75 per cent Sj: balance. comer. made. A quenching temperature of 750°C. produces almost as high a hardness on subsequent aging as do quenching temperatures of 850' and 900°C. Several foundries have spent years of active and intelligent effort in trying to control the casting and heat-treating variables of nickel-silicon bronzes and finally gave up the attempts because of the inconsistencies of results.2 This undesirable characteristic was not manifest in the ultimate hardness or conductivity but primarily in tensile strength and ductility, as shown in Table I. The variation in tensile properties was often much greater than that existing on the alloys

Jan 1, 1941

By S. Frederick Ravitz

IN recent years, two theories of the mechanism of flotation have received a great amount of attention. One of these is Ostwald's theory of linear flotation,1 according to which most collectors contain three active groups: a hydrophilic or water-loving, a metallophilic or mineral-loving, and an aerophilic or air-loving group. Under the action of these three groups, Ostwald considers a single ring of collector molecules at the three-phase air-liquid-mineral boundary sufficient to bring about the flotation of the mineral particle. Siedler, Moeller and Reddehase2 objected to this theory immediately after it was presented, but most of their objections were answered by Ostwald.3 Very recently, however, Wark and Cox4 have more adequately criticized this theory, and their criticism makes its validity appear doubtful. The other important recent theory is the "chemical" theory of flotation, proposed by Taggart and his coworkers,5 who maintain that "all dissolved flotation reagents, which, in flotation pulps, either by action on the to-be-floated or on thenot-to-be-floated particles affect their floatability, function by reason of chemical reactions of well recognized types between the reagent and the particle affected." In general, they appear to consider most flotation results to be brought about by purely chemical reactions between the collectors and the products of oxidation present

Jan 1, 1933

By C. R. Woodcock, J. S. Mason

In almost any situation where particulate or granular bulk solids have to be conveyed, whether for a distance of a few metres or for many hundreds of metres, a pneumatic conveying system may be considered. Conveying by pipeline is convenient and clean, but running costs may be substantial because of the heavy air consumption and the trend has therefore been towards dense-phase transport in which the ratio of conveyed solids to conveying air is kept high. This paper concentrates on air-float conveying, which can be regarded as an extreme form of dense-phase conveying where the bulk solid is fluidised in a channel and then caused to flow, either by inclining the channel or creating a pressure gradient along 'it. Various designs of air-float conveyor for upward, horizontal and down- ward transport of powders are discussed, with special emphasis on the latter case. In situations where a continuous downward slope can be provided, the combination of air-fluidisation and gravity flow results in a conveying system that, for many kinds of bulk particulate solid, would be hard to better in terms of convenience, reliability and economy. The paper is concluded with a discussion of design features and performance of practical air-gravity conveyors, involving the handling of various bulk particulate solids, both in research and in full-scale industria1 applications.

Jan 1, 1980

By R. J. Pearce, I. Whittle, J. J. Stobbs

The oxidation kinetics of UCu5 in carbon dioxide have been studied over the temperature range 350° to 850°C. At any one temperature, two successive parabolic rate constants are obtained. Up to 650°C, the temperature dependence of the reaction is snzall and the first parabolic rate constant is higher than the second. At temperatures of 690°C and above, there is a very marked temperature dependence and the second rate constant is the higher. Metallo-graphic examination has shown that attack proceeds via internal oxidation. THE oxidation behavior of the U-Cu intermetallic compound, UCu5, in carbon dioxide was briefly examined during investigations aimed at selecting oxidation-resistant uranium-alloy coatings.' It was found that an extremely thick, coherent scale was formed coated at the scale-gas interface with a thin, apparently continuous layer of copper. A more detailed investigation of the oxidation of UCus has now been made. Previous published work2 has been limited to a brief examination of UCu5 in connection with the oxidation of a U-1 wt pct Cu alloy in carbon dioxide. No attempt was made to explain its behavior, but the work indicated that attack proceeded by intern oxidation, with the formation of a layer of copper on the surface of the specimen. EXPERIMENTAL UCus was prepared by arc melting the stoichio-metric amounts of high-purity copper* and uran-

Jan 1, 1965

By David Swan

No mystery shrouds the discovery of chromium. The indefatigable French chemist Vauquelin, in reporting his discovery of this chemical element to 1'Institut National in 1798, concluded his discourse with the statement: "I place before the eyes of the Institute a small quantity of chromium and several of its most re- markable combinations." Working with the so-called "red lead of Siberia, Vauquelin not only prepared numerous chemical compounds of the new metal, but he reduced the oxide to the metallic state. These chemical compounds possessed a variety of remarkably distinctive colors; so, acceding to suggestion, Vauquelin named the new element chrome (chromium), a derivative of the Greek word chroma, meaning color. Siberian "red lead" (crocoite) was not plentiful; however, it was not long before Vauquelin's prediction was realized that the chemical compounds of chromium would become useful in the arts when sources of chromium became more readily available. Although chrome-iron ore (chromite) became obtainable in France, the United States and elsewhere during the early part of the nineteenth century, it is interesting to note that from 1828 to about 1860, Maryland, Pennsylvania, and others of the eastern United States furnished almost the entire chrome-ore requirements of the world. Several countries each in turn have since dominated for certain periods the supply of chromite. In recent years, the largest tonnages have come

Jan 1, 1953

By F. A. Champion

The work described in this paper was carried out in the Research Laboratories of the British Aluminium Company Ltd., under the general direction of A. G. C. Gwyer, Scientific Manager of the Company. In considering the effect of stress?corrosion conditions on metals, or the failure of metal through stress corrosion, it is evidently advisable to adopt a clear definition of the meaning of those phrases. There appears to be general agreement that stress-corrosion conditions may be defined as the continuous application of static stress to a metal while it is exposed to corrosive conditions, but recognition of the occurrence of true stress-corrosion in a metal is often a difficult matter giving rise to some confusion. For the purpose of this paper stress corrosion in a metal is defined as the acceleration of corrosion by the application of static stress. On this view it is necessary to test a metal not merely under stress-corrosion conditions, but also under the same corrosion conditions without the simultaneous application of stress, if the liability of the metal to stress corrosion is to be assessed. Failure of a metal under stress-corrosion conditions is sometimes quoted as evidence of stress corrosion (for example, by Althof(1)2), but this evidence is totally inadequate if the above definition is

Jan 1, 1945

By Max W. Bowen, A. J. Weinig

The important part that dissolved oxygen plays in the cyanide treatment of gold and silver ores is commonly recognized by most metallurgists and mill men. But heretofore there has been no simple method on which the mill man could rely for determining the amount of oxygen in the various mill solutions. A few methods are adaptable to the laboratory, such as the gasometric1 determination by actually measuring the oxygen, Winkler's2 iodometric method, and Schutzenberger's3 method, which depends on the reducing action of sodium hyposulfite on a blue solution of indigo carmine; but these are not readily adaptable to the needs of the mill man and cannot be applied to cyanide solutions without modification. The gasometric method is the most accurate but it takes too long to complete a determination. White's4 method (a colorimetric method that depends on the degree of coloration imparted to a solution of pyro-gallic acid in the presence of caustic soda) although much more rapid than any of the methods named, often gives misleading results on account of grading of colors of different solutions, which nearly always contain various kinds of salts. The method herein described was devised for the use of the mill man, the aim being to develop a simple, practical, accurate method. It is a modification of the Schutzenberger method and depends on the reducing

Jan 1, 1925

By Ajoy K. Ghose

INTRODUCTION Longwall mining made its debut in Indian coal mining scene around 1900. Despite this headstart, the application of the method has been slow and halting. Currently, there are some 16 operating longwall faces only in different Indian coalfields contributing to perhaps less than 3 percent of the total underground coal production. Ambitious plans for expansion of longwall mining notwithstanding, apprehensions on the cavability of Indian coalmeasure roof rocks and some unsavoury experiences with face collapses in caved longwalla have impeded wider adoption of the technique. Between 1960 and 1983, some 41 caved longwall faces were worked in Jharia, Raniganj, Karanpura and Korba Coalfields in India, of which 6 faces reportedly had collapsed(1). The first powered support longwall face was started in August 1978 at Monidih colliery which marked a major step forward in the introduction of advanced technological system in Indian coal industry. This paper attempts to analyse critically the experiences with longwall ground control in caved longwall faces in India. Experiences from powered support faces at Monidih, Dhemomain and Pathakhera are synthesized to provide an appraisal of the present status of caved longwall faces under the Indian coalmeasure roofs, which thus far have been characterised as “massive”. The geotechnical site factors at the powered support faces are evaluated and conclusions drawn on the pre-assessment of caving characteristics and support resistance required at the faces.

Jan 1, 1984

By William L. Grube

PECIMEN preparation for electron metallography involves several steps, such as polishing, etching, replicating, mounting, and shadowing. Although each step must be done with care, the operation requiring the utmost attention is etching. Proper etching is important because the relief pattern developed on the surface of the specimen by the etchant, and reproduced as minute differences in thickness of the replica, determines entirely the amount of detail seen in the final micrograph. The characteristic colored stains, sometimes used in light metallography to simplify identification of certain microconstituents, cannot be tolerated because there is danger of introducing artifacts in the replicating operation. It is also quite difficult to remove plastic replicas from stained specimens. A suitable etchant for electron metallography must, therefore, in all cases exhibit a preferential attack upon each of the microconstituents present sufficient to result in a difference in surface elevation. When only two microconstituents are present, it is not too difficult to find a suitable etchant since their physical or chemical properties are generally sufficiently different to result in a marked difference in attack by the etchant. For example, picral (a saturated solution of picric acid in methanol used as an immersion etch) is a satisfactory etchant for the specimen shown in Fig. 1 consisting of iron carbide particles embedded in a ferrite matrix.'

Jan 1, 1952

By Carl H. Samans

THE INFORMATION AVAILABLE on the rolling characteristics of the precious metals-gold, silver, the platinum metals and their alloys-is incomplete and mostly from scattered sources. In the present paper an effort has been made to assemble and correlate it and to fill in some of the gaps that exist. GENERAL ROLLING CHARACTERISTICS SOME EFFECTS OF IMPURITIES Gold and its alloys are generally considered to be hot short and hence are usually rolled cold. Cold rolling of the yellow, green, and pink gold alloys. Which customarily contain gold, silver, copper and zinc and frequently some nickel as well, introduces no new problems since reasonable reductions are quite feasible and the alloys show little tendency to fire crack in subsequent annealing. The white gold alloys. which usually contain little or no silver and 10 pct or more nickel, are very susceptible to fire cracking1 and hence wrist he given relatively heavy reductions, i. e., 8-10 pct or more per pass with a total reduction of about 50 pct between anneals, to minimize this tendency. In addition, it is preferable to keep the bar as flat as possible during rolling. Although no comprehensive study appears to have been made of the effects of impurities on the cold rolling characteristics of gold alloys, the observations of Nowack2 on the effects of small

Jan 1, 1948

By L. W. Eastwood

THE recrystallization and grain-growth phenomena of cold-worked metals have considerable industrial importance because of their role in the fabrication of metals. For this reason, and because of the general academic interest in the subject, these processes have received consider-able attention since the time of J. E. Stead's paper1 on The Crystalline Structure of Iron and Steel. There are considerable differences of opinion regarding the theory of recrystallization and grain growth and also differences in the observation of the modus operandi of the processes themselves. The value of many of the existing quantitative data on grain growth is decreased by the failure to distinguish between the grain sizes just after complete recrystallization and those resulting from coales-cence. For this reason also, the value of the diagrams of stable grain sizes, like those produced by Bass and Glocker2 and Czochralski3, is lessened in so far as an interpretation of the facts of recrystallization is concerned. It is hoped that the data presented in this paper will help to clarify and to simplify the facts relating to recrystallization, and at the same time will show that some of the present-day conceptions are unten-able. A paper on the theory of recrystallization, with additional data, will be completed in the near future by the writers.

Jan 1, 1935

By Richard B. Greenwalt

INTRODUCTION Direct reduction of iron ores has unquestionably become established as an important step in the worldwide steelmaking industry. The history of this development has been long and fraught with difficulty. In 1800, Champlain suggested the direct reduction concept using carbon and a shallow hearth vessel. Roughly 100 years later, Jones attempted a commercial process using carbon and producer gas in a rotary kiln. During the early years of this century, numerous attempts were made to start commercial direct reduction plants using such processes as Hoganas, Wiberg, Krupp-Renn, and others. Most of these were short lived, being abandoned due to a variety of technical and economical factors. Today, however, a new generation of direct reduction processes has emerged. We enter 1977 with at least 40 commercial plants in operation using 15 processes in 14 countries. These plants have combined total annual capacity of roughly 10 million tonnes of direct reduced product. Many articles have been written, and projections made, concerning the future growth potential for direct reduction. As is al- ways the case with projections, the numbers vary, but the outlook does not. Anyone who participated in the years of effort that have gone into this field of endeavor should be excited and justly rewarded by noting the shape of the curve in Figure 1.

Jan 1, 1977