Search Documents

By Blamey Stevens

In this paper, which is a logical extension of my paper, The Laws of Intrusion,1 the various pressures of emanation and their mechanical causes and effects on the large scale of nature are determined, and a classification of emanations is deduced therefrom. • The Subterranean. Sea. The subterranean sea is here defined as the intercommnnicating water contained in the trains of pores and fissures of the rocks down to great depths. Whether the actual amount of water constituting this subterranean sea be large or small, does not enter into the present argument, since the static pressure of this water at any particular depth is not a function of the quantity : it involves only the depth and the density of the water. Densities. The total pressure at depths down to 10 or 15 miles is made up of the rock-stresses investigated in my previous papers, and the pressure of the subterranean sea. The latter component must evidently be equal to the weight of a solid column of the overlying water of unit sectional area. As mater expands with heat, it should really be necessary to sum the density at every level. A knowledge of the densities of mater under a variety of conditions is therefore needed, but does not seem ever to have been ascertained for such combined pressures and temperatures as we have to consider. The specific gravity of water at 28' C. for various pressures up to 400 atmospheres, has been determined by Barus, 2 who

Jan 1, 1913

By J. J. Bailey, R. C. Dean

Dr. Maurer has reviewed the large and confused field of rock mechanics and drilling. We have focused our attention on advance drilling and the disengagement of rock. To understand drilling in greater detail is certainly desirable, but such understanding does not necessarily hold any certain promise of near-term practical advancement. In the longer term, it is probably essential. Present work on drilling and our understanding of drilling falls roughly into three separate classes (and, indeed, these are in no way peculiar to drilling): 1) we have knowledge of certain (scientific) topics which seem to be relevant to the process, 2) we have knowledge of the drilling process in both qualitative and quantitative terms from observation of the actual process, and 3) we have certain modeling procedures, by which we bridge the gap between these two previous areas. The usefulness of our scientific knowledge depends critically upon this last item. In all our following remarks we shall consider only those problems of drilling and the disengagement of rock in which the rock behavior is essentially brittle. Let us start by examining some of the problems of constructing an even moderately detailed theoretical model of the drilling process in the small. The prospects of any near-term success in that direction seem extremely meagre; nor is it clear that any great advancement in the practical art of drilling is even likely to result from the construction of such a detailed model. On the other hand, as we shall suggest later, considera-

Jan 1, 1967

By B. Haimson, C. Fairhurst

One of the main functions of rock mechanics research has been to find ways of determining in-situ stresses. Many methods have been suggested, the most significant ones calling for measurements inside bore- holes. These methods usually employ some instrumentation for the purpose of measuring hole deformation. Several years ago, a new method was suggested by Scheidegger,l based on previous work by Hubbert and Willis.2 It was the method of "hydraulic fracturing," which had been introduced by the oil industry in 1948 for the purpose of oil-well production stimulation. Basically, hydraulic fracturing consists of sealing off a section of a borehole, pumping in a fluid, and pressurizing it until fracture occurs. If pumping is continued vigorously, the fracture is opened up and extended. In an oil field, such an artificial fracture increases the overall permeability of the formation and usually enhances production. During the entire operation, the variation of pressure with time is ordinarily recorded. Hubbert,2 Scheidegger,1 Kehle,3 and others have shown that the recorded pressures can be theoretically related to the magnitudes of the principal in-situ stresses; the orientation of the fracture can often be used to determine the direction of the principal stresses. The advantage of hydraulic fracturing over the present in-situ stress determination methods is simplicity: no sophisticated instrumentation is required inside the borehole; hence, the stresses can be measured at any depth. Moreover, if the formation is impermeable to the fracturing fluid, no elastic constants of the rock are required in calculating the stresses, a

Jan 1, 1970

By V. F. Hollister

Although it is apparent that porphyry copper deposits may have formed in the Andean orogen from Permian time onward, commercial deposits thus far developed appear to have Cenozoic ages only. Following Chilean usage, the porphyry deposits are divided into either (1) a stockwork or (2) a tourmaline breccia model. As indicated by evidence cited in the paper, stockwork-type deposits tend to be related to major strike-slip structures which may be either transcurrent or transverse faults related to plate movements, while the tourmaline breccia type may more frequently form independently of regional faults. Stockwork types may be conjugate fractures that intersect and ramify as a network of veins and veinlets, cutting altered rock, and genetically related to a major regional fault, or in other cases they may reflect the intersection of two large fault structures. Circular fracture patterns may more rarely occur in stockwork deposits in response to a specific intrusion. Tourmaline breccia types are characterized by circular and radial fractures genetically connected in some way with touramline breccia pipe development or an intrusive piercement that preceded it. Each structural model contains mineralized intrusions which have a close time-space relationship to ore, and in each model mineral paragenesis is similar, regardless of age or location in the plate. Also, each model contains the same type of alteration halos (phyllic, argillic, propylitic) as are developed in intrusive centers in porphyry copper deposits found in North America. The potassic zone is exposed best in the older deposits. Examples of each type of deposit are illustrated, demonstrating the feature evolved.

Jan 1, 1975

By J. M. Davey

Lead-zinc sulphide ores at Mount Isa are currently treated at the rate of 180,000 long tons per 28 day period in the No. 2 Concentrator of Mount Isa Mines Limited. Prior to June 1966 lead-zinc ore was treated in part of the No. 1 Concentrator up to a rate of 70,000 long tons per period. Since 1955, two major changes in ore type being processed have occurred. Because of these changes, problems arising from treatment of the ore have altered and during the period several major changes in practice have been advocated and experimentally tested. Most of these flow sheets were developed with a view to overcoming one major problem in the ore. These were invariably abandoned as the Mount Isa lead-zinc ore contains a number of equally major problems all of which must be overcome in the treatment process. MINERALOGY The orebodies are situated in the Mount Isa Shale Group which is Proterozoic in age (Carpentarian System). The sediments consist dominantly of fine grained dolomitic, quartzo-feldspathic shales and siltstones. Specifically, the Mount Isa orebodies lie in the Urquhart shale formation which is characterised by sediments of high albite and orthoclase content denoting a large volcanic component. The Urquhart shales are approximately 3,500 feet thick and extend at least north and south of Mount Isa for 20 miles in each direction. In the area of the silver-lead-zinc orebodies the Urquhart shales are highly pyritic and have a relatively high carbon content. The

Jan 1, 1970

By J. Eldridge, K. L. Komarek

Activities of aluminum in solid Fe-Al alloys have been determined between 0 and 75 at, pct Al and 1100" and 1400°K by an isopiestic method in which iron specimens, heated in a temperature gradient, are equilibrated in a closed all-ceramic system with aluminum vapor. The activity of aluminum in these alloys shows a strong negative deviation from Raoult's law at low concentrations but increases rapidly above 40 at. pct Al. The enthalpy and entropy of mixing me both negative. For an alloy with equiatomic composition the values are: HM = -7300 cal and SM = -0.85 eu. Sodium chloride has been added at lower temperatures to accelerate the evaporation of aluminum. Equations have been derived to calculate activities of aluminum from experimental data. THE Fe-Al system has been the object of a great number of investigations.' Most of these studies have been concerned with the phase diagram and specifically with the order-disorder reactions in the range of solid solutions of aluminum in iron. The results have been compiled by Hansen2 and presented as a complete phase diagram, Fig. 1. More recently, Taylor and ones' have found that both ordered and disordered alloys can exist in the a field up to the solidus curve separated by a line starting at 18.75 at. pct Al at room temperature up to 37 at. pct Al at 1375°C. Chipman and coworkers4-7 have studied repeatedly the activity of aluminum in liquid dilute Fe-Al alloys. They have measured the distribution equilibrium of aluminum between liquid iron and

Jan 1, 1964

By Albert Phillips

As EARLY As 1824, Haidinger1 described crystals of native copper that were, according to Dana,2 "probably twinned parallel to the octahedral plane and normal to this axis." In 1837, Rose3 very clearly demonstrated that native copper crystals were commonly twinned on the octahedral plane. Lasaulx,4 in 1882, described polysynthetic octahedral twins and stated that enclosed twinning lamellae were observed. Even on crystals formed artificially by. electrolysis, twinning was observed as early as 1886, by Brown.5 Many other descriptions of twinning in native copper and in gold and silver are to be found in the literature, and in every case with which we are acquainted the twinning is conformable to the spinel law; i. e., the octahedral plane is both twinning and composition plane. Metallurgists have long been familiar with the straight-sided bars or bands that commonly occur within the irregularly outlined grains of metallic crystalline aggregates. They are certainly found in nearly all metals of the face-centered cubic type after cold working and annealing. If a specimen showing these bands is rotated, keeping the angle of incidence of the illuminating beam constant, they usually exchange color contrast periodically with their respective matrix crystals. Also slip lines, when produced in these specimens, nearly always show a change in direction upon passing through the bands, giving rise to the "stairway" effect often illustrated in metallurgical textbooks. Apparently the only quantitative observations on bands of this sort were made by Osmond and Cartaud6 on austenitic steel. They selected,

Jan 1, 1928

By Joseph Chalmers

PROBLEMS dealing with the movement or ,migration of fluids through porous beds have been the subject of much research. The subject is not peculiar to the production of oil and gas, as many investigators have studied the nature of this movement and its relationship to the problems of other industries. Darcy1 conducted a series of experiments relating to the percolation of water through filter beds. King2 carried on an extensive series of laboratory experiments with the object of formulating some conception of the rate of movement of water through soils and sand strata in the drainage of surface water into underground channels and subsequent recovery of this water through wells drilled into the source beds for irrigation purposes. Slichter3 undertook a study. of the same problem from a mathematical standpoint, and more recently Furnas4 has investigated the flow of gases through beds of broken solids with particular reference to blast-furnace operation. With specific reference to gas production, Muskat and Botset5 of the Gulf Research Laboratory undertook an experimental study to establish quantitatively the characteristics of and laws governing the flow of gases through consolidated and unconsolidated porous materials of fine texture with a view of predicting the performance of gas in an underground reservoir. There seems to be a general agreement that many of the relationships between the numerous factors influencing the flow of fluids through porous materials are far too complicated to be attacked by analytical methods based upon a knowledge of hydrodynamics. For gases, the laws of

Jan 1, 1932

By E. S. Tankins

The main purpose of this work was to study the effect of gold on the activity coefficient of oxygen in the liquid Fe-Au alloy and to determine how copper and silver change the activity coefficient of oxygen. A preliminary investigation has been made of equilibrium in the reaction of hydrogen with oxygen in some of the liquid gold alloys. The experimental method, which has been described in detail elsewhere,' consisted of bubbling accurately known H-A-water vapor mixtures through the Fe-Au alloys contained in alumina crucibles within a vertical closed furnace. When equilibrium was reached, the samples were quenched by rapidly lowering the crucible under an atmosphere of argon to a water cooled brass fixture at the bottom of the furnace tube. The melts were found to freeze from the top in less than 4 sec. The heats were carefully prepared for oxygen analysis. The oxygen content was determined by vacuum fusion analysis.' Only high purity electrolytic materials were used in this investigation. The activity and free energy of oxygen in the liquid iron alloys were studied by means of the reaction; The data for the 80 Fe-Au alloys, obtained as a function of temperature, are summarized in Table I and presented in Fig. 1, where log is plotted against . The results can be expressed by: The data were obtained using water vapor-hydrogen ratios between 0.04 and 0.30, and a 25 pct H2-75 pct A mixture. An oxygen content between 0.030 and 0.060

Jan 1, 1970

By T. M. Morris, F. M. Lewis, W. C. Lay, Gordon M. Bell

Part I of this chapter is concerned with the description of and metallurgical data pertaining to the flotation circuits used in the London mill of the Tennessee Copper Co., at Copperhill, Tenn. The ores treated at the London mill are massive complex sulfides, in which pyrrhotite and pyrite are the predominant minerals. Other sulfides are chalcopyrite and sphalerite; magnetite is also of economic value. The approximate mineralogical analysis of the ore is shown in Table 1. [ ] The chalcopyrite and sphalerite are closely associated with pyrrhotite as shown by the tracings of micrographs (Fig. I), which are representative of the mill feed. Fig. la illustrates the type of locking between pyrrhotite and chalcopyrite; Fig. lb illustrates the way in which sphalerite is attached. Thesephotographs indicate that it is not practical to break all of these attachments. Hence, in order to produce concentrates with satisfactory grades and recoveries, most of the locked chalcopyrite particles must be recovered into the copper concentrate, and the locked sphalerite-pyrrhotite particles must be separated from the iron concentrate. A copper concentrate, a zinc concentrate, and an iron concentrate are made. Typical metallurgical results are tabulated in Table 2. HISTORICAL In 1922 the London mill started as a copper concentrator, with a capacity of 300 tpd, and in 1926 an additional flotation circuit was added to recover the iron sulfide remaining in the copper tailing. In 1927 a zinc flotation circuit was installed between the copper and the iron flotation circuits. This procedure was not satisfactory because the iron recovery was low, due to the

Jan 1, 1962

By Clarence E. Sims

DURING the past several years the steel casting industry has made studies of heavy castings in which the test bar has been taken from heavy sections rather than from attached or separately cast coupons. It has been noted that the ductility properties of these heavy sections are often lower than those normally expected. Such lowered ductility is usually accompanied by a spotty test bar fracture and the ductility values often can be greatly improved if a low-temperature aging treatment is given to the casting. A loss of ductility of this type is considered "abnormal," since it is not accompanied by an increase of tensile strength or hardness, and "temporary" when the ductility can be restored by aging. The cure of such an abnormal condition represents a real improvement in the quality of the steel. Some hundreds of previous investigations, largely qualitative in nature, have established beyond reasonable doubt that hydrogen is normally present in newly manufactured steel and that this gas, in small amounts, can cause a temporary abnormal loss of ductility. The commonly observed association of high gas content and low ductility has given strong evidence for the presumption that hydrogen, possibly assisted by other gases, is the primary cause of the low ductility observed. Accordingly, the Steel Founders' Society of America has, since Nov. 1, 1944, sponsored investigations at Battelle Memorial Institute whose primary objective is to obtain quantitative information on the relation of the amount of hydrogen and nitrogen in steel, together with associated methods of steelmaking and treatment, to low-ductility effects and porosity.

Jan 1, 1947

By Philip Wilson

THE Province of British Columbia covers 382,000 sq. mi., about 250,000 sq. mi. of which have not been prospected. In fact, the coast country and the islands are so heavily timbered and the surface covered with so thick a mantle of soil, muskeg, and, over broad areas, glacial drift, that prospecting, and even trail breaking are extremely difficult. It is only along the coast or stream channels, or above the timber line, or where snow or rock slides have scoured the surface that rock outcrops can be found. Glaciers nestle in many of the cirques and fill the valleys in the higher ranges. Great ice sheets and perpetual snow persist in certain localities, thus reducing the exposed areas worth prospecting. Almost the entire country has been subjected to intense glaciation, so that the conspicuous oxidized outcrops of orebodies typical of the south-western United States and Mexico do not exist and surface bodies of enriched or oxidized ore are rare. With few exceptions, the mines1 of the Province are working primary ore. Developments have proved that some of these orebodies are large and important, although usually comparatively low in grade. Besides the few mines that have produced most of the minerals, there are many small mines, but their total output is unimportant. Considering the number of mines and prospects and the widespread mineralization, it is strange that no really great mines, comparable in size and richness with those in the western United States have been found.

Jan 8, 1922

YEARS ago, when metal mining was more an adventure than a well-organized business, it was often said (with some color of truth) that unless a mine could stand bad management or mismanagement, it was not much good. Today, the natural excellencies of an ore deposit are merely a challenge to the engineers to exploit it as skillfully, as efficiently, and as profit- ably as possible. A vast amount of competent and imaginative engineering management (which includes economic analysis no less than the technologic arts of mining ore and treating it) has been required to make New Cornelia the smooth-running and successful operation that can be seen at Ajo today. New Cornelia was acquired by the Phelps Dodge Corporation when it absorbed the Calumet and Arizona Mining Company in 1931. Next to Morenci, it doubtless is the corporation's biggest asset. It in no way detracts from the achievement of Phelps Dodge engineers to say that they had an admirable ore deposit to work on. New Cornelia ore, as mined, is relatively low in grade and the deposit is by no means the largest of the Porphyries; but it has these attractive features : (1) It is peculiarly suitable for opencut mining because: (a) The overburden of waste rock lying above the ore deposit was (it has long since disappeared) almost negligible. (b) The deposit is roughly circular in horizontal section, with the horizontal dimensions four to five times as great as the maximum thickness. (Nevertheless, eventually some underground mining may be desirable.)

Jan 1, 1957

By N. Brown, M. Herman

IT has been pointed out by Cottrell' and Fisher that long-range order would produce superdis-locations, consisting of two partial dislocations separated by an out-of-phase region. The mutual repulsion of the partial dislocations is balanced by the surface tension of the out-of-phase domain boundary joining the dislocations (Fig. 1). The calculation of the equilibrium spacing of the dislocations has yet to be made. The argument uses the Bragg and Williams theory of long-range order." The metal under consideration is the A-B, body-centered type, such as ß brass. The slip system is taken to be [Ill], (110). Since nearest-neighbor interactions are considered, only the atoms position in the two (110) planes adjoining the slip plane have to be labeled. Corner sites are called a and a' in the top and bottom (110) planes, respectively. Similarly ß and ß are the body-centered sites. Thus, a and ß and 0 and a sites are nearest neighbors. Assume that the bottom plane moves and the top plane is fixed during slip; the atoms in a and ß sites exchange sites but atoms in a and ß sites remain fixed. Fraction of A atoms in a sites, for example, is given by fa and fa. for the un-slipped and slipped condition, respectively. Similarly number of A atoms in the a sites is given by n, and n'a for the unslipped and slipped condition, respectively. As the dislocation moves into the ordered region the change in number of A-A bonds is given by

Jan 1, 1957

By Raimo Matikainen

Sublevel stoping has been used in Finland since the 1930's and today more than ten under- ground mines have adopted it as their main stoping method (Fig. I). Approximately 80% of the total underground tonnage is mined by sub- level stoping (Table 1) The first mines to introduce the sublevel stoping method in Finland were limestone mines. The development of sublevel stoping was very slow up to the mid 1960's when the switch to trackless mining started and the increase of mechanization lead to higher capacity and productivity. The method itself has been almost the same since the 1950's when long hole drilling was introduced. According to a future prognosis sublevel caving will give way to sub- level stoping; on the other hand, open pit mining will at the same time grow rapidly with some new mineral orebodies, which will he brought into production. Most Finnish orebodies are, however, only marginal ores and they could not support mining with more expensive methods than open pit mining or sublevel stoping. The future of sublevel stoping seems relatively bright. GEOLOGICAL AND ROCK MECHANICAL BACKGROUND The rock mechanical conditions in Finland are in general relatively good and the rocks firm. The compressive strength is normally 40 - 150 Mpa and modulus of elasticity 40 - 200 Gpa. Low values are common in altered and fractured rocks and near the ore contact Rock stress measurements have been carried out already for 20 years for mine design and monitoring purposes. The results of these measurements show that relatively high horizontal stresses seem to be common (Fig. 2).

Jan 1, 1981

By Hsun Hu

The formation of annealing textures in high-purity silver, from the various rolling textures obtanled in the course of texture transition, was studied. It was found that from a brass-type rolling texture the recrystallization texture is mainly (120) [211] type, which is quite different from the recrystallization texture of brass. From a predominantly copper-type rolling texture, the reclystallization texture is mainly (100) [001]. The recrystallization texture of silver- varies also with the degree of purity. In each case, however, the reorientation can be expressed as [Ill] rotations of 30° to 40°, which is consistent with the oriented growth theory of the formation of annealing textures. ThE recrystallization textures of rolled silver were studied long ago by Glocker and co-workers (1924-27) and were reported to be (113) [iil] upon annealing at low temperatures.1 Since that time, no further study of the recrystallization textures of silver, particularly with the modern techniques of quantitative texture determinations, has been reported in the literature. In a previous study2y3 it was found that the rolling texture of high-purity silver (99.999 +pct pure) is changed gradually from the common silver- or brass-type to the copper-type by raising the temperature of rolling from 0" to 200°C. The formation of annealing textures from the various rolling textures in the same material is, therefore, of considerable interest. The present paper constitutes the results of such a study. MATERIAL AND METHOD Specimens were taken from the same strips of high-purity silver* that were used previously for

Jan 1, 1962

By Bernard Schneider

The diversity of methods available to engineers and geologists for studying rock masses is a reflection of the fact that, despite the rapid and encouraging progress made over the last few years, there is still no unified and comprehensive method which can be used to predict the over- all behavior of a foundation. Nevertheless, it is agreed that the fundamental characteristic affecting the engineering properties of rock is fissuration, and this paper de- scribes a few new or improved methods of studying fissuration and its influence on major engineering factors such as permeability, deformability, or internal stresses in the rock volume. TESTS ON SAMPLES Conventional tests on samples using thin slices can be improved by staining the slices before cutting with certain ionic dyes which have an affinity for certain types of surface. This shows up the microdiscontinuities. For example (quoted terms are French trade names) : "Turquoise Motylhne JSA" will show up porous alteration of basic feldspars. "Vert brillant SA" is used for acid feldspars. "Fushine ASA" will show up voids in all rocks. A mixture of "Turquoise" and "Rhodamine BSA" will show up zones of alteration in all types of feldspars. With this technique, it is easy to make an optical classification of the different structural types, e.g.: (1) rocks completely free from voids; (2) rocks with microfissures, which in turn can be subdivided into (a) rocks with microfissures secant to the mineral structure, (b) rocks with microfissures parallel to the mineral structure, and (c) rocks with ran-

Jan 1, 1970

By Clemens Jones

An interesting paper by J. E. Merion and Edward Hart, in Volume I., No. 2, of the Journal of Analytical Chemistry, on the Decomposition of Blast-Furnace Cinder by Acid, describes a plan of sampling the cinder by means of a previously-heated iron bar thrust into the cinder car or into the cinder at the notch, and then allowed to cool, thus chilling the cinder which adheres to the bar, and rendering it decomposable by hydrochloric acid, of 1.12 sp. gr. A short series of results is given, from which the deduction follows that blast-furnace cinder " is decomposed perfectly when chilled." Where many silica determinations are to be made, this method, if reliable, would effect notable economy of time and reagents. The conversion of insoluble silicates by fusion with an alkaline carbonate, together with the subsequent solution, evaporation, drying, etc., is destined to remain the standard method. But all fusionmethods are time-consuming and expensive. Chilling appears to render the supplementary method available for all practical purposes, in the determination of silica in cinder. But, with a view of securing more evidence on the subject, and in view of the fact that uniform results were not obtained by employing this method, it was decided to test the method in the laboratory of the Thomas Iron Company where a large number of silica determinations are made. The experience met with may not be devoid of value, both theoretical and practical. Mr. Iles's paper, in the Chemical News, Volume L., 1881, doubtless suggested to several chemists, connected with iron metallurgical

Jan 1, 1888

IN GATHERING material for this chapter on Yerington and the one to follow on Silver Bell, the A.S.& R. project near Tucson, Arizona, I was fascinated at the way the two stories paralleled each other. For example, here are a few instances: (1) The first copper mining in the Yerington district of Nevada was in the late 1860's; the first in the Silver Bell area in 1873. (2) Each district was served by a branch railroad about 25 miles long from a main line of the Southern Pacific (by quizzical coincidence); and, in each instance, the railroad was later abandoned and torn up. (3) Each district had a sizable blast-furnace smelter ten or fifteen miles from the principal mines, and in each instance the smelter was later dismantled for junk. (4) Up to 1954, the Yerington district was credited with a production of 100,000,000 lb of copper; the Silver Bell district with 80,000,000 lb. (5) In each district the entire production had come from deposits other than the low-grade ore bodies now being exploited. (6) In each instance, existence of the low-grade deposits of the Porphyry type was recognized in the period circa1910-1914 and a substantial amount of exploratory drilling had been done, on one deposit at Yerington and on two at Silver Bell. (7) In each instance, the properties containing the Porphyry ore were acquired by a strong company (Anaconda Copper Mining Company at Yerington and American Smelt-

Jan 1, 1957

By Frank Van Horn

IT is customary to ascribe two general modes of occurrence to natural gas, namely shale. gas which, as the name indicates, is found in' shale, and reservoir gas, which occurs ill sandstone, conglomerate and dolomitic limestone. Both of these types are found in the Cleveland district. The shale gas has been produced on a small scale for a long period of years, probably dating back as far as 1883. Shale gas is a low-pressure gas, small in volume with variable pressure, and is limited to no definite horizon. It is generally independent of oil, may last for a long time, and is not dependent to any great extent on the structure of the rocks. There are many such wells in the district which range from 400 to 1,840 ft. in depth, although most have been completed at about 800 ft. This indicates that the wells pass through the Cleveland and Chagrin shales into the Huron or Portage shale of the Upper Devonian. During the last 2 years great interest has developed in a deeper-seated reservoir gas. What is commonly called reservoir gas is generally a high-pressure gas occurring in large volume at a definite horizon. Oil may, or may not, be associated with the gas, and in most regions in which reservoir gas is found, the geological structure is of great importance. This type of gas occurs in all large fields such as those of West Virginia which have been supplying Cleveland until the recent discovery of local gas at great depths in commercial amounts.

Jan 1, 1917