Search Documents

By R. G. Powell, R. Schuhmann, E. J. Michal

Liquidus surfaces in the ternary system FeO-Fe2O3-SiO2, were determined from 1250' to 1450°C by the procedure of equilibrating small samples in platinum crucibles, quenching, and microscopic examination. The experimental results were combined with previously published information to construct a ternary diagram for the system showing the entire temperature-composition range of stability of iron silicate slags. Metallurgical applications of the diagram, especially in copper smelting, are discussed briefly. IRON oxides are almost unique among the common oxide constituents of metallurgical slags in that the iron occurs in two different states of oxidation, ferrous and ferric. Moreover, in liquid slags the degree of oxidation of the iron is readily changed by reactions of the slags with oxidizing agents or reducing agents. This behavior of iron oxides in slags accounts, for example, for the effective transfer of large quantities of oxygen through slag layers in open hearth steelmaking. In this process, oxygen supplied by reactions at the gas-slag interface is dissolved in the slag with the oxidation of ferrous iron to ferric. Ferric oxide is transported across the slag layer by convection, and at the slag-metal interface the oxygen reacts with liquid metal while the ferric iron is reduced back to the ferrous state. Another group of processes in which variation in degree of oxidation of iron has great practical importance is in copper smelting. In matte smelting and converting, such large proportions of the iron are oxidized to the ferric state that problems are encountered in preventing or controlling the formation of solid magnetite. The ferrous-ferric relationship also affects the attack of iron oxides on high-SiO2 refractories, which appears to be most severe under reducing conditions for which ferrous iron predominates. Darken and Gurry' determined the chemical properties and phase equilibria of pure iron oxide slags. Their data show that iron oxide melts can have compositions ranging almost all the way from FeO to Fe2O3. The melts of lowest oxygen contents, which exist in equilibrium with metallic iron, approach ferrous oxide in composition but still have a small percentage of ferric oxide. The melts of highest oxygen contents, which have oxygen dissociation pressures of 1 atm, are above magnetite in oxygen content, with over two-thirds of the iron in the ferric state. The previously established phase diagrams for silicate slag systems all show FeO as the iron oxide component. However, Bowen and Schairer? who determined the FeO-SiO2 diagram and many of the other diagrams used by slag chemists, have been careful to point out that their systems always contained both ferrous and ferric iron. Thus, their data are for limiting mixtures with minimum contents of ferric iron, obtained by melting and equilibration in iron crucibles. Under these conditions, the Fe2O3 percentages found by analysis were small enough to justify simplification of the published phase diagrams by calculating the Fe2O3 to equivalent FeO and ignoring Fe2O3 as an additional component. On the basis of experimental measurements of melting points of iron oxides on silica in the presence of various gas mixtures, Darken3 worked out phase diagrams for the Fe-Si-0 system which show the important phase equilibria in terms of temperature and gas composition. This study clarified many aspects of the application of the phase rule to the FeO-Fe2Oa-SiO2 system and was an important basing

Jan 1, 1954

By Norman Weiss, H. W. Kaanta

CUSTOM ores reach across the New Mexican mesa to American Smelting & Refining Co.'s new lead-zinc mill at Deming. The influx of ores justified increasing mill capacity from 12,000 tons per month to 20,000 tons per month with the installation of a second milling section. Deming mill has met a complex material handling problem with the successful instrumentation of modern machinery and knowledge. A tight, compact plant does a big job with the aid of the latest ore moving equipment. Location and Layout The mill is located three miles northwest of Deming in the tumbleweed covered valley of the Mimbres River, 30 miles north of the Mexican border. Deming has a population of 4000 and is about halfway between Lordsburg and Las Cruces and 54 miles southeast of Silver City. The AT&SF and the SP railroads and U.S. Highways 70, 80, and 260, cut across the mesa to the town. Asarco mill station is east of the AT&SF single track, and north of Deming. The nearly level terrain is covered with fine sand supporting only yucca and tumbleweed. Compacted gravel at depth affords excellent foundation bearing. The climate is semi-arid, but the district is underlain by water-bearing strata. Tailing disposal space is plentiful. The Deming site appeared favorable because of easy rail and highway access, central location in a mining district, excellent climate, plentiful water supply, space for all present and future requirements, and proximity to a town. The milling plant is a 250-ft square. The rail spur forms the west side; sampling plant, fine-ore conveyor and bins are on the east; track hopper, primary conveyor, and crushing plant lie on the south; and the mill building completes the north side of the square. Construction The mill site was chosen and the land purchased in 1,946 and 1947. Design began in 1948, and Stearns-Roger Mfg. Co. of Denver started construction in June 1949 completing work in April 1950. Construction is steel and concrete throughout, with main concrete floors supported on cellular steel beams. The building is covered by galvanized corrugated iron, attached to the frame by welded Nelson studs, and made dust tight at the joints with roofing paper and asphalt sealing compound. Crushing and Sampling Custom ores, delivered to the mill by railroad cars or trucks, are weighed on arrival. A Robbins car shaker dumps the ore into a 100-ton capacity steel hopper. Adjacent is a 40-ton truck hopper. Three 36-in. Pioneer apron feeders supply ore from the receiving hoppers to a 36-in. conveyor which runs to the crushing plant. A tramp-iron detector protects the primary crusher except when handling magnetite containing ores. A 2 ½ -in. spaced grizzly precedes the primary Traylor 24x36 in. jaw crusher set at 4 in. A Symons 4-ft cone crusher in closed circuit with 48x78 in. Robbins Gyrex screen completes crushing to 5/8 in. The discharges of both crushers drop upon a common conveyor, which, after gaining sufficient elevation, transfers ore to a return conveyor. This return conveyor passes under a suspended magnet and over a magnetic head pulley to the Gyrex screen. Screen undersize is conveyed by a 20-in. belt to the sampling plant. Crushing rate varies from 60 to 90 tons per hour. Ores containing magnetite and pyrrhotite nullify the magnetic detector and overload the magnets

Jan 1, 1952

By P. Shahinian, R. L. Stegman, M. R. Achter

Creep strength has been determined as a function of oxygen pressure for nickel at 510" and 600°C. Creep-rupture life drops from its highest value at the ultimate vacuum of 10-7 torr to a high pressure plateau of nearly constant life which, at 600°C, commences at torr. This behavior is described in terms of a model that relates surface gas adsorption and the generation of fresh crack surfaces. In a calculation based a this model the predicted pressure beyond which the creep strength should not decrease further has been found to agree well with the observed value. The introduction of oxygen during creep in vacuum was found to cause a prompt rise of the creep rate. The magnitude of the environmental effect was much less than generally observed in fatigue and this is attributed to the diffarent crack morphologies in creep and fatigue. GASEOUS environments are known to affect creep resistance adversely1-5 but the effects have received less attention than the much larger ones in fatigue. At low temperatures it has been shown for nickel that the creep rates are faster and the rupture lives are shorter in air than in vacuum and that these environmental effects can be correlated with faster crack growth rates in the reactive environment.' In support of a mechanism of gas adsorption at the crack tip to explain the above effects, a calculation based on kinetic gas theory showed that surface coverage by gas was not as rapid as the exposure of fresh metal at the crack tip in the ultimate vacuum but was in air.7 In fatigue a number of investigations have demonstrated that the reduction of life with gas pressure usually follows a step curve with most of the reduction occurring in a transition range at intermediate pressures and little or no change at high and low pressure.8 There have been no studies, however, in which creep strength has been determined as a function of reactive gas pressure to see whether similar effects would be found. This investigation was undertaken to study the kinetics of the environmental effect in the creep of nickel. EXPERIMENTAL PROCEDURES The environmental creep apparatus was constructed to minimize many of the experimental conditions which can cause scatter in data. Dead weight loading is employed and weights are contained within the environmental chamber to eliminate bellows and the necessity for compensation for gas pressure changes. Elongation over the specimen gage length is recorded from a Riehle Model DV Controlled Environment Extensometer which provides readout to 2.5 x 10- in. Temperature is monitored and controlled from a thermocouple at- tached to the specimen gage length to +0.5oC or better. The freon trapped oil diffusion pump vacuum system included an auxiliary liquid nitrogen trap and, with a wide range variable conductance leak valve, pressures from the ultimate vacuum of 10"7 to l03 torr of any desired gas are obtainable. Pressure is measured by means of a hot filament ionization gage below 10"3 torr and a NRC Model 530 Alphatron Vacuum Gauge above 10-3 torr. The oxygen, which was leaked into the environmental chamber, was an Aviator's Grade of 99.5 pct purity with a dew point of -80°F. Analysis of the nominal 99.8 pct Ni showed the following percentages of major impurities: 0.02 C, 4.01 Mn, 0.005 Si, 0.01 Cu, 0.02 Fe, and 0.034 Mg. Cylindrical specimens were machined with a 0.180

Jan 1, 1970

By M. King Hubbert, David G. Willis

A theoretical examination of the fracturing of rocks by means of pressure applied in boreholes leads to the conclusion that, regardless of whether the fracturing fluid be of the penetrating or non-penetrating type, the fractures produced should be approximately perpendicular to the axis of least stress. The general state of stress underground is that in which the three principal stresses are unequal. For tectonically relaxed areas characterized by normal faulting, the least stress should be horizontal; the fractures produced should be vertical with the injection pressure less than that of the overburden. In areas of active tectonic compression, the least stress should be vertical and equal to the pressure of the overburden; the fractures should be horizontal with injection pressures equal to or greater than the pressure of the overburden. Horizontal fractures cannot be produced by hydraulic pressures less than the total pressure of the overburden. These conclusions are compatible with field experience in fracturing and with the results of laboratory experimentation. INTRODUCTION The hydraulic-fracturing technique of well stimulation is one of the major developments in petroleum engineering of the last decade. The technique was introduced to the petroleum industry in a paper by J. B. Clark,' of the Stanolind Oil and Gas Co. in 1948, and since then its use has progressively expanded so that by the end of 1955 more than 100,000 individual treatments had been performed. The technique itself is mechanically related to three other phenomena concerning which ah extensive literature had previously developed. These are: (1) pressure parting in water injection wells in secondary-recovery operations, (2) lost circulation during drilling, and (3) the breakdown of formations during squeeze-cementing operations, all of which appear to involve the formation of open fractures by pressure applied in a wellbore. The most popular interpretation of this mechanism has been that the pressure had parted the formation along a bedding plane and lifted the overburden, notwithstanding the fact that in the great majority of cases where pressures were known they were significantly less than those due to the total weight of the overburden as determined from its density. Prior to 1948, this prevalent opinion had already been queried by Dickey and Andresen,2 in a study of pressure parting; and by Walker,"' who, in studies of squeeze cementing, pointed out that the pressures required were mostly less than those of the overburden, and inferred that the fractures should be vertical. J. B. Clark,' in his paper introducing hydraulic fracturing, and later Howard and Fast," and Scott, Bearden, and Howard," also of Stanolind, postulated that the entire weight of the overburden need not be lifted in producing horizontal fractures, but that it was only necessary to- lift an "effective overburden," requiring a correspondingly lower pressure. Hubbert,7 in discussing the paper by Scott and associates, pointed out that the normal state of stress underground is one of unequal principal stresses; and in tectonically relaxed areas, characterized by normal faults, the least stress should be horizontal. Therefore, in most cases, fracturing should be possible with pressure less than that of the overburden and, moreover, such fractures should be vertical. Harrison, Kieschnick, and McGuire,8 also on the expectation that the least principal stress should be horizontal, argued strongly in favor of vertical fracturing. Scott, Bearden, and Howard6 observed that, when

Jan 1, 1958

By R. E. Cole, A. M. Gaudin

OLEIC acid, a standard flotation reagent, has generally been preferred to other fatty acids. Because oleic acid differs from saturated fatty acids by the presence of one carbon-to-carbon double bond and because the flotation operation is one in which extremely intimate exposure of the reagent to oxygen is obtained, it appeared possible that the value of oleic acid as a flotation collector was related to the oxidizability of its double bond. To test this hypothesis, the floated mineral, fluor-ite, was leached with a solvent capable of extracting the adsorbed reagent and the extract was analyzed.' Results show that oleic acid is not oxidized during flotation, although some oxidation can be obtained if the flotation operation is repeated many times and if oxygen in place of air is employed as the gas during flotation. Incidentally, it was found that lino-leic acid which has two nonconjugated double bonds is not affected appreciably more than oleic acid. Linolenic acid which has three nonconjugated double bonds is measurably altered even during one flotation step, using air. The fatty acids used, from the Hormel Foundation, were of the highest purity. The quantity of fatty acids employed in each test was sufficient to float the mineral, but less than the theoretical amount required to form a monolayer at the mineral surface. The purpose of this limitation was to eliminate droplets of oil smeared on the adsorbate-covered mineral surface. The mineral was dried in vacuum at about 60 °C. Effective leaching was obtained by use of a solution of 1 pct hydrochloric acid in absolute alcohol. The extract was separated from the solvent by distillation, with final recovery of the extract in carbon tetrachloride. The identity of the extract was tested by a combination of analytical procedures including infrared spectroscopy, saponification number, iodine number, and index of refraction. At the outset, great hopes for accurate quantification of oleic acid oxidation had been entertained in regard to the method of infra-red spectroscopy. Unfortunately, because the double bond in the oleic acid is so sym- metrically located at the center of the molecule that it provides very weak absorption bands, accurate quantitative analyses were not obtained. Nevertheless, infra-red spectrograms suggested the absence of double-bond oxidation during flotation. Iodine number, semi-micro method, provided a critical test of the extent to which fatty acids oxidized during flotation, see Table I. The index of refraction was used in a qualitative rather than quantitative fashion, and its findings corroborated those obtained by the iodine-number method. It is concluded, in the case of fluorite and C-18 fatty acids having one or two nonconjugated double bonds, that there is practically no change of the fatty acid molecule or ion during the flotation operation. It would appear, therefore, that the extraordinary utility of these reagents is related to some property of the compounds other than the oxidizability of their double bonds. Acknowledgment The research reported herewith was sponsored by the Research Division, U. S. Atomic Energy Commission, and for this help the authors express their appreciation. Reference 'R. E. Cole: "Double-Bond Reactivity of Oleic Acid During Flotation." Thesis submitted in partial fulfillment of the requirements for the degree of M.S. at the Massachusetts Institute of Technology.

Jan 1, 1954

By G. H. Kennedy, H. E. Criner

CYCLONE thickeners are "hydraulic centrifuges" designed either to produce a maximum practical separation between the water and solids of a feed slurry or to classify the slurry solids according to particle settling rate. The possibilities of utilizing the thickener to "close" plant water circuits have been investigated. Since the thickener becomes an integral part of the plant water circuit when installed, the basic means by which the solids content of all circulating water systems must be controlled is reviewed. All coal not separated from the circulating water by means of dewatering screens or settling devices must be bled from the plant at the same rate as they are being fed or created by degradation. If this were not true, the circulated volume would finally be completely filled with solids. If the rate of bleed is low, the solids concentration in the bleed and circulating water generally will be high. To keep a reasonable circulating water concentration, large amounts of fresh water must be supplied and the bleed rate must be high. These conditions are usually undesirable because of the difficulty in securing fresh water, the loss of large quantities of coal, and the pollution of nearby streams. Thickeners are the primary stage in the separation of the water contained in the bleed from the coal. Since a thickener, when operating with reasonable efficiency, usually cannot be expected to deliver an underflow containing less than 50 pct water, secondary dewatering devices such as a slurry screen or vacuum filter must be used to separate additional water from the bleed. The surface area required by the filter or screen will be nearly proportional to the total water which must be handled, and therefore the thickener becomes necessary to hold down the original cost. The water separated from the coal is then returned to the plant circuit to maintain the water balance and thus becomes the source of fresh water. It is not necessary to return clear water to the plant to maintain control of the circulating water concentration. It is only necessary that the bleed dewatering devices remove coal in all sizes at a rate equal to that at which these sizes are entering the circulating water. However, practically speaking, in order to maintain low solids concentration, it is usually necessary that the thickener have good recovery characteristics on bituminous coals in those sizes down to 400-mesh. The thickener can remove the smaller sizes from the closed-circuit system at the "solids in" rate and prevent their "build up" in the circulating water as shown in Fig. 1. With the portion of the feed water going directly to the underflow, comes the very fine solids not concentrated by the cyclone. All the larger solids are removed from the feed and delivered in a concentrated condition at the underflow. To apply thickeners with some reasonable assurance that operating requirements will be met, it is necessary to know the rate at which solids of all sizes must be removed from the circulating water and to know the thickener characteristics. The required removal rate of fine solids not recovered by other dewatering devices may be estimated from the size distribution and tonnage of the plant feed with a reasonable allowance for degradation in the circulating water system. A more reliable estimate may be secured by sampling the plant bleed water during a constant load period.

Jan 1, 1952

By L. W. Saperstein, D. Yeung, L. B. Phelps

Introduction The success of preventive methods for the mitigation of coal mine drainage formation will require a marriage of the minimization of initial coal mine drainage formation, the minimization of toxic fluid formation after toxic material disposal, the minimization of the mobilization and transpor¬tation of formed toxic fluids, and the maximization of the rate of diultion and attenuation of the formed toxic fluids. This paper contributes to the understanding of factors af¬fecting mobilization and dilution and attenuation of formed toxic fluids. When water containing a salt content different from in situ pore water in the soil is passed through a body of soil, the concentration of salts in the outflow will gradually change composition in a manner that depends on the kinds of hydraulic processes that occur in the soil. These processes are molecular diffusion, lateral dispersion, longitudinal dispersion, chemical reactions or exchange, physical adsorp¬tion, and biological retardation. This note considers only the first three processes. These three microscopic processes can be analyzed statistically on a probability basis. Such results, confirmed experimentally, indicate that a tracer introduced instantaneously as a point source will tend to form a Gaussian normal distribution as it moves downstream (Todd, 1964). Dilution During Flow The closed-form soltuion for pulse or instantaneous injec¬tion of a tracer during confined flow in a homogeneous porous medium shows that the maximum tracer concen¬tration at a point in space, x, after the time interval, t*, is given by [ ] where Aa is the effective flow cross-sectional area; A is the column cross-sectional area; a is soil porosity; M is mass of the injected tracer; C is concentration of the tracer in the permeating fluid and is a function of x and t*; D is the longitudinal dispersion coefficient; and va is the interstitial fluid velocity (Klotz and Moser, 1974). Therefore, the following conclusion can be made: • For a medium with a constant longitudinal dispersion coefficient, D, a constant soil porosity, a, a constant cross¬sectional area, A, and a fixed mass of injected tracer, M, Cmax will decrease as the time of peak outflow concen¬tration t* increases. • For a medium with a constant longitudinal dispersion coefficient, D, a constant soil porosity, a, a constant cross¬sectional area, A, a fixed mass of injected tracer, M, and a constant interstitial fluid velocity, va Cmax will decrease as the distance of travel, x, increases. • For a medium of constant cross sectional area, A, con¬stant soil porosity, a, a constant mass of injected tracer, M, and a fixed distance of travel, x, Cmax will decrease as D/va increases. Klotz and Moser (1974) concluded that D is about proportional to no.3 where r) is the kinematic viscosity; D is about proportional to a-3 where a is soil porosity; D in¬creases with increasing grain size; D increases as grains become less spherical; D increases with greater grain rough¬ness and angularity; D increases with increasing uniformity coefficient; and D is significantly affected by grain size and uniformity coefficient. The remaining parameters are not significant. Numerical Simulation Studies Numerical simulation studies were used to investigate the nature of flow and the optimum length of a toxic package within a saturated porous medium of fixed dimensions and configuration (Fig. 1). The width and position of the package was maintained constant (Phelps et al., 1981). Results indicate that if the package extends throughout the length of the model, the flow is vertically downward and

Jan 1, 1984

By Wei-Kao Lu

A general rate equation is derived for gas -solid reactions in metallurgical processes by considering the contributions of chemical reaction at inter-phase boundaries and diffusion through the solid product layer simultaneously. This equation takes care of the whole range continuously from purely diffusion control to purely chemical reaction control. The parabolic law,' McKewan's equationa derived with the assumption of interface area control and the equation derived by Kawasaki et al. with the assumption of purely diffusion control are found as the limiting cases of the corresponding forms of the general rate equation. Many metallurgical processes involving gas-solid reactions have been extensively studied. The common examples of these processes include the reduction of oxides to metallic products, the roasting of sulfides to oxides or chlorides and the oxidation of metals. Gas-solid reactions consist of at least two kinds of steps; one involves the transport of reactant and product to and from the reaction zone and the other is the chemical reaction taking place at the interphase boundaries. In the limiting cases one or the other of the above mentioned steps will be much slower than the other and is then rate controlling. For example, the oxidation of metals is diffusion controlled and obeys the parabolic law.' On the other hand, if the diffusion rate is much larger than the chemical reaction rate then it will be controlled by the chemical reaction rate. This latter case occurs for the reduction of iron oxides studied by McKewan. If the rate of diffusion and of the chemical reaction have the same order of magnitude, a more detailed analysis is necessary. Thus at the beginning of the reaction when the solid and gaseous reactants are in direct contact, the reaction should be chemical reaction rate controlled as no diffusion process is involved. At the other extreme as the reaction zone moves further into the solid, the diffusion distance becomes greater and the diffusion rate continuously decreases. Eventually, therefore, for a sufficiently large sample the rate must become diffusion controlled. As the transition from one controlling step to the other must be continuous, we cannot describe this transition period by either of the two limiting cases. In this paper the author attempts to derive a general rate equation for gas-solid reaction systems. This is effected by considering the rates of diffusion and chemical reaction simultaneously from the state of pure diffusion control to pure chemical reaction control. I) DERIVATION The system under consideration is made of at least three phases, namely the gaseous one, the solid reactant, and the solid product as shown in Fig. 1. The notations are listed at the end of the paper. The mass transfer process involves the diffusion of reactants and products across the solid product layer. It is reasonable to consider that no chemical reaction will take place in the solid product layer with respect to both gaseous reactant and product. For the characteristics of local equilibrium of the system, the diffusion process is really in a quasi-steady-state. It will be proved in the following paragraphs. Then we can invoke the law of conservation of mass valid for all chemical species passing through the layer. The solid reactant sphere has an initial radius, ro, after a fraction of completeness of the reaction, the unreacted core has a radius ri, where r, is in the solid product region. Let Cg be the activity of gaseous reactant in the

Jan 1, 1963

By Pramod C. Thakur

Introduction Methane is contained under pressure within the fractures and adsorbed on the surface of the coal seams and adjacent strata. It is released into the mine atmosphere during mining of the seam creating explosive gas-air mixtures. Large volumes of air, sometimes as high as 20 tons of air for each ton of coal mined, are circulated constantly to dilute and carry away methane from coal mines. Removal of methane from solid coal, wherever high methane emissions occur, has been discussed by Spindler and Poundstone (1960) and Thakur and Davis (1977). Methane control in longwall gobs is much more complicated. As longwall mining progresses, the overburden continually subsides, and the immediate roof caves behind the roof supports. Even the underlying strata heave and open up communication channels feeding gas to the longwall gobs. The pressure of gas in the underlying and overlying strata is usually higher than the ambient air pressure in the mine. Thus the mine workings become natural pressure sinks, into which gas flows from the entire disturbed zone. Winter (1975) defines this zone as the "gas emission space". Depending on the number of gas-bearing zones in the gas emission space and their gas contents, the total methane emission from longwall gobs could vary from a few to more than one hundred cubic meters of gas per ton of mined coal. Hence the ventilation of longwall faces demands a large quantity of air. This ventilation need is further enhanced by high air losses specially on caving faces (with no stowing of the gobs). The old system of longwall ventilation, the 'U' pattern, where all the air was brought down one gate road and exited through the other gate road, loses large quantities of air through gobs giving a high methane concentration at the return end of the face. The 'Y' ventilation pattern where intake air is brought down both head and tail gate roads relieves the situation to some extent but, on most longwalls, some kind of methane control is still needed. With the onset of longwall mining in Europe several decades ago, the initial work on methane control on longwall has naturally been done there. The basic principle of methane control has always been, and still remains, some means of "bypassing methane from the gas emission space without letting it mix with the mine air". In most cases the bypassing mechanism is either a strategically located borehole or a roadway. A successful methane control program depends on the following basic premises: a. Determination of the geometry of the gas emission space and location of gas bearing horizons therein. b. Estimation of the rate of methane influx into the longwall gob. c. A scheme to bypass the gas in the most economic and efficient manner and thus prevent it from entering the mine atmosphere. In successful methane drainage programs a high proportion, usually between 50 and 70 percent, of the total gas emissions in a working district is removed before it can enter the mine airways. Advantages of methane drainage can be summarized as: 1. Generally reduced methane levels in the mine leading to increased safety and productivity. 2. Reduced air requirements and corresponding savings in ventilation horsepower. 3. Faster rate of advance for development headings and economy in the size of headings. 4. Possible use of mine gas as an additional source of fuel. The purpose of this paper is to briefly review the geometry of gas emission space and methane influx therein and discuss more successful European and U.S. longwall gob gas control techniques.

Jan 1, 1981

By M. T. Simnad, C. E. Birchenall, M. H. Davis

The transport mechanisms previously proposed in wustite and hematite have been confirmed by movement of inert markers during the growth of these phases. By similar measurements the mechanism for magnetite has been determined. The rates of growth of multilayer scales on iron, magnetite and hematite on wustite, and hematite on magnetite have been measured. All rates are found to be diffusion controlled under the conditions of the experiments. MANY studies have been made of the rate of oxidation of iron in both the low temperature, film-forming region and the high temperature scaling range. The interpretation of the results has been greatly complicated by the formation of multi-layered scales containing the various phases of iron oxides. In most cases no attempt has been made to determine the composition of the scale and its dependence on time of oxidation in a quantitative manner. However, several recent studies'" have taken this variable into account. It is generally agreed that the growth of thick scales on iron follows a parabolic rate law for the increase of total thickness. In the thin film region agreement has been claimed with parabolic equations of various forms and with logarithmic equations. The discussion here will be concerned only with the formation of scales of considerable thickness, greater than several microns, although some of the conclusions may be applicable to thin films. A brief survey will be given of the solid phases of the iron-oxygen system, the stability of wiistite in bulk and in thin films, the relative densities of iron in the metal and oxides, and the kinetics of forma- tion of oxide scales on iron. New experimental results will be introduced at several points during the discussion, and an attempt will be made to formulate a mechanistic picture consistent with these observations. The experimental techniques are described in an appendix. Iron-Oxygen System Fig. la shows the iron-oxygen phase diagram. Wüstite ("FeO"): The lowest of the oxides has a NaCl type cubic lattice formed by close-packing of the relatively large oxide ions with the smaller iron ions arranged in the interstices. The ionic radius for 0' is about 1.3 A, while Fe++ has a radius of about 0.8A and Fe"' about 0.7A. Its range of existence on the phase diagram is very wide for an ionic material of this type and does not seem to include the stoi-chiometric composition FeO. These deviations appear to be well established as vacancies on iron lattice sites by the comparison of lattice parameters and densities for a series of compositions by Jette and Foote.4 The limits of the field are disputed, but the work which seems most reliable" indicates vacancies in from 5 pct to more than 12 pct of the iron sites. In order for the crystal to be electrically neutral, there must be electron holes which correspond to the formation of trivalent iron ions equal to twice the number of vacancies. Magnetite ("Fe³O4"): Considerable disagreement also exists in the literature about the stable range of the Fe³O4 field. Some diagrams show the Fe³O4 composition to be lower in oxygen than the formula indicates, but Schenck6 gives a diagram from the

Jan 1, 1952

By C. J. Ramsburg

THE construction and operation of by-product coke-oven plants in America are essential to strong national defense and of the greatest importance to many widely diversified undertakings as well as to safety and health. CARBONIZATION PROCESS Coal used under a boiler or in a locomotive is consumed by combustion. Coal used in a by-product oven is distilled or carbonized, meaning that heat is applied to the coal, out of contact with air, causing a distillation that removes the volatile matter in the coal in the form of gas and vapor, leaving coke as a final product. From the gas and vapor distilled from the coal, many valuable substances can be secured, known as by-products. Hence the name "by-product oven." The simplest example of this principle can be shown by means of an ordinary clay pipe. If powdered coal is placed in the bowl of the pipe, the opening of the bowl is plugged with clay, and the bowl placed in a flame, the bowl will become hot, transferring the heat through the wall of the bowl to the coal within. When this coal attains a temperature of about 950°F., gas will begin to pour out of the pipe stem, and this gas may be lighted. A black liquid also will exude from the stem of the pipe. This is tar mixed with certain other products. What remains in the bowl after distillation is coke. A coke oven corresponds to the bowl of the pipe. A modern oven of the latest type is a refractory brick chamber approximately 42 ft. long and 14 ft. high, averaging 18 in. in width. The oven is filled with coal through closable charging holes in the oven top. Each end of the oven consists entirely of a self-sealing door, the removal of which permits the finished coke to be discharged by means of a power-operated pusher machine. The ovens are built in batteries, and the heating is effected by gas burned in vertical flues in the oven walls, each set of flues heating the walls of two adjacent ovens. Such ovens carbonize a charge of approximately 18 tons of coal in 18 hr., or have a daily throughput of 24 tons per oven, producing about I 7 tons of coke. In times of need, the output may be increased by raising the temperature of flues, thus shortening the coking time. There is one great essential difference in principle between distillation in a clay pipe and in a coke oven. In the 18-in. oven, the distillation proceeds from two parallel walls held at a high temperature (over 2000°F.) and instead of all the coal being heated at once, the distillation is a progressive one creeping inward. The average travel of this heating is 1/2 in. per hour from each vertical wall, and as the volatile products are formed progressively they must push away from the interior toward the wall through the previously formed hot coke, then up the walls and over the top of the coal charge, finally escaping through the outlet pipe. This results in a cracking of the components into many different and valuable substances not formed when the carbonizing temperature is low.

Jan 1, 1942

By H. R. Stahl

The ore of the Southeast Missouri lead district consists essentially of galena in dolomitic limestone. The galena usually is in a very finely disseminated condition. The experience of recent years in the concentrating plants of the St. Joseph Lead Co. has shown that dry crushing carried to a point where about 90 per cent of the ore passes a 14-mesh screen liberates the larger portion of the galena, and minimizes further necessary reduction in rod or ball mills. Concentration practice has attempted to carry size reduction to a point where economic unlocking of the galena is obtained, without causing undue sliming of the very friable galena. While 60 per cent of the tonnage of the district is treated by the flotation process, only 40 per cent of the total concentrates is produced by that means, as efforts have always been made to keep the grade and tonnage of flotation feed as low as possible. The milling practice of the district for some years has recognized the generally accepted idea of better selective grinding in rod mills as compared with ball mills, with the attendant decrease in production of fines. The function of rod and ball mills in the various concentrating plants is the grinding of table middlings and coarse tailings that carry lead values too high to be discarded. The simplified flowsheet in Fig. I illustrates the place of grinding mills in the circuit. The arrangement of classi- fiers, tables and mills constitutes a closed circuit within somewhat flexible limits. In 1937 experiments were conducted in replacing the ball charge in a 6 by 4-ft. ball mill with rods 2 in. in diameter and 51 in. long. This step was taken with some hesitancy, as it was easy to picture a mass of tangled and crossed rods. However, no difficulties developed, and after a short trial period, six more ball mills were converted to rod mills. These mills are of the spur gear and pinion, belt-driven type, using in most cases a 75-hp. motor and having a 9½-in. open trunnion discharge. As ball mills, they carried a charge of 16,000 to 20,000 lb. of balls, 2 in. in original size. The feed to the mills was dewatered by dewatering wheels and introduced at 70 to 75 per cent solids, with a single scoop feeder. One change in mill design was found advisable when rods were introduced. The existing end liners had an outward flare of 3½ in. in 12 in. These were replaced by linings having vertical interior faces, in order to prevent undue end travel of the rods. This change gave an effective working length of 52¾ in. inside the mill. No alterations were made in the shell liners, which are of the smooth type, made of manganese steel 2 in. in original thickness. The rods at present in use are 51 in. long and 1¾ in. in diameter. The composition has been varied at times; at present they contain 0.70 per cent carbon and 0.70 per cent manganese. Some breakage and etching occurs as the rods become small, but this is considered preferable to using softer rods, which may kink and cause tangling of the charge. The mill charges

Jan 1, 1947

The Goodman Mfg. Co., Chicago, builders of underground electric mining machinery, celebrated its 50th Anniversary on April 23rd. The company has a complete line of cutting machines, loaders, conveyors, locomotives, and shuttle cars for service in both coal and metal mines. The Joy Mfg. Co. has received, under the provisions of the Economic Cooperation Administration, an initial order in excess of $1,000,000 for equipment to be used in the mechanization of iron ore mines in France. While the equipment will be used in various privately owned mines, the order was placed through the French Society for the Development of Mechanical Mining. Included in the equipment are the company's recently developed hard rock loaders and shuttle cars. American Brake Shoe Co. has consolidated all operations of its Canadian subsidiaries into one corporation, the Dominion Brake Shoe Co. Ltd., Montreal, Canada. The products of Dominion Brake Shoe include brake shoes, track equipment, manganese steel castings, automotive brake lining, air compressors, and paint spray equipment. Exhibits of more than 2000 electrical products, processes, and techniques, ranging from precise aircraft instruments to complex working models of steel mill, textile and other industry equipment, will be displayed in the "More Power To America Special" when it makes its nationwide tour this spring. C. H. Lang, Vice-President in charge of sales for General Electric's apparatus department, said that the train will visit the country's key industrial centers for inspection by utility and industrial executives and municipal leaders. The train will be hauled by an Alco¬G-E two-unit, 4000-hp., Diesel-electric locomotive which in itself will be part of the unusual series of displays. Sizing of Excavators and Hauling Equipment. The Power Crane and Shovel Association has released a 24-page bulletin dealing with the proper sizing of excavators and hauling equipment, Technical Bulletin No. 3. Rubber Conveyor Belting. "Installation, Care and Maintenance of Rubber Conveyor Belting" is the title of a booklet just published by the Carlyle Rubber Co., New York. Power Transformers. The manufacturing procedure of Allis-Chalmers small power transformers is described in a new 28-page bulletin, 61B6094A, covering the core and coil unit, no-load tap changer, tank construction, cooling methods, oil preserving systems, bushings, terminal compartments, indicators and testing of transformers. Safety Equipment. General Scientific Equipment Co., Philadelphia, has released a 46-page, fully illustrated catalog on personal protective equipment and industrial safety devices. This new catalog covers respiratory devices, eye protection, hats, gloves, carboy pumps, drum pumps, and miscellaneous safety equipment for use in mines, industries, etc. Osmosalts. The Osmose Wood Preserving Co., Buffalo, N. Y., has issued a bulletin on Osmosalts, the wood preservative which, say the manufacturers, makes timber last three to five times longer, slashes maintenace costs, stops rot, and resists wood-destroying insects. Jigs. The Dorr Co. has acquired the Pan American jigs and they are now known as the Dorrco-Pan American jigs. Originally developed as a gold-saving device for dredges, the simplicity, ease of operation. efficiency, and negligible maintenance of these jigs have resulted in wide adoption on all types of placer operations, in the closed grinding circuits of gold mills, and on many applications where a coarse bed concentrate is separated from the ore gangue.

Jan 5, 1950

By H. R. Stahl

The ore of the Southeast Missouri lead district consists essentially of galena in dolomitic limestone. The galena usually is in a very finely disseminated condition. The experience of recent years in the concentrating plants of the St. Joseph Lead Co. has shown that dry crushing carried to a point where about 90 per cent of the ore passes a 14-mesh screen liberates the larger portion of the galena, and minimizes further necessary reduction in rod or ball mills. Concentration practice has attempted to carry size reduction to a point where economic unlocking of the galena is obtained, without causing undue sliming of the very friable galena. While 60 per cent of the tonnage of the district is treated by the flotation process, only 40 per cent of the total concentrates is produced by that means, as efforts have always been made to keep the grade and tonnage of flotation feed as low as possible. The milling practice of the district for some years has recognized the generally accepted idea of better selective grinding in rod mills as compared with ball mills, with the attendant decrease in production of fines. The function of rod and ball mills in the various concentrating plants is the grinding of table middlings and coarse tailings that carry lead values too high to be discarded. The simplified flowsheet in Fig. I illustrates the place of grinding mills in the circuit. The arrangement of classi- fiers, tables and mills constitutes a closed circuit within somewhat flexible limits. In 1937 experiments were conducted in replacing the ball charge in a 6 by 4-ft. ball mill with rods 2 in. in diameter and 51 in. long. This step was taken with some hesitancy, as it was easy to picture a mass of tangled and crossed rods. However, no difficulties developed, and after a short trial period, six more ball mills were converted to rod mills. These mills are of the spur gear and pinion, belt-driven type, using in most cases a 75-hp. motor and having a 9½-in. open trunnion discharge. As ball mills, they carried a charge of 16,000 to 20,000 lb. of balls, 2 in. in original size. The feed to the mills was dewatered by dewatering wheels and introduced at 70 to 75 per cent solids, with a single scoop feeder. One change in mill design was found advisable when rods were introduced. The existing end liners had an outward flare of 3½ in. in 12 in. These were replaced by linings having vertical interior faces, in order to prevent undue end travel of the rods. This change gave an effective working length of 52¾ in. inside the mill. No alterations were made in the shell liners, which are of the smooth type, made of manganese steel 2 in. in original thickness. The rods at present in use are 51 in. long and 1¾ in. in diameter. The composition has been varied at times; at present they contain 0.70 per cent carbon and 0.70 per cent manganese. Some breakage and etching occurs as the rods become small, but this is considered preferable to using softer rods, which may kink and cause tangling of the charge. The mill charges

Jan 1, 1947

By J. Szekely, R. G. Carr

A method is presented which allows the extension of the Ergun equation for the description of gas flow through packed beds in a nonisothermal regime. The pressure profile in the packed bed is calculated by the establishment of a differential energy balance and the iterative integration of the integral equation thus obtained. The predicted values of the pressure distribution were found to be in excellent agreement with those measured experimentally, under carefully controlled conditions. MANY metallurgical processes are carried out in systems in which a gas stream and particular solids are contacted in a packed bed arrangement under strongly nonisothermal conditions. Ore sintering, the firing of pellets, the operation of regenerators, blast furnace technology may be quoted as examples. Although many aspects of these systems have been extensively studied, an important variable, the pressure distribution and the relationship between pressure head and flow rate, received only little attention to date. The purpose of the paper is to present a brief survey of relevant previous work, followed by a more rigorously formulated model, together with experimental results that afford ready comparison of theoretical prediction with measurement. PREVIOUS WORK A great deal of information is available in the chemical engineering literature on flow phenomena in porous media.' The experimental results pertaining to gas flow were generally interpreted in terms of models based on the analogy with the flow through a pipe of an incompressible, isothermal fluid. Of the numerous, semiempirical correlations that have been proposed to relate pressure drop to the volumetric flow rate, the Ergun equation2 is generally regarded as the most satisfactory: The strong nonisothermality of the metallurgical systems previously mentioned would render the direct applicability of Eq. [I] rather doubtful as both density and viscosity are temperature-dependent. Ergun has used Eq. [I] for estimating the pressure drop in the stack region in the blast furnace by neglecting the viscous term and evaluating the gas density at the integral mean temperature.3 His calculations showed a rather variable agreement with measurements and it was uncertain whether the discrepancy found was attributable to the model or to the inaccuracies often inherent in measurements on an industrial scale. Other work on nonisothermal systems includes studies of the pressure distribution in sinter beds, notably by Voice et a1.4 and Mitchell.5 Mitchell developed a method involving the subdivision of the bed into several zones and assigning average property values (temperature, gas density, and so forth) to each zone. The pressure drop was then calculated for each zone by using an expression analogous to Eq. [I]. This method was an improvement over that described by Voice et al., but even here prediction and measurement differed by as much as 30 pct in certain cases. It would appear that no really satisfactory methods are available for the prediction of pressure drop in packed beds with a strongly nonisothermal regime. The method involving subdivision of the bed into small enough sections, that may be regarded as isothermal, would show promise; however its validity has to be tested by both a rigorous formulation and comparison with experimental data obtained under controlled conditions. In the following a formulation is presented together with experimental data allowing ready practical evaluation of the theory. FORMULATION The mechanical energy balance over an infinitesimal section of a packed bed may be written as follows:

Jan 1, 1969

By M. F. McCarty, R. S. Olson

New organic flocculants of high-molecular weight are replacing lime, glue, and starch in liquid-solid separation. Of these synthetic materials, poly-acrylamides are outstanding. Polyacrylamides form a class of compounds varying widely in composition and activity. Separan 2610, one of the first of these flocculants' released to the mining industry in 1954, is described' as a high-molecular weight polymer of acrylamide with or without a copolymer material and with some replacement of amide by carboxylic groups. MECHANISM OF FLOCCULATION In practice, flocculation makes solids settle faster and filter better. But two opposing factors control it. The random motion that causes particles to collide favors Van der Waals' forces, which hold the particles together. The effect of zeta potential opposes this contact, and particles are mutually repelled. Flocculation can be achieved by reducing the magnitude of the zeta potential; this is the mechanism of flocculation by lime addition. The way in which polyacrylamides accomplish flocculation is not fully understood, but the action is undoubtedly comp1ex and probably varies considerably depending on the system. To begin with, the active groups of these compounds have an extremely high affinity for solid surfaces, probably by hydrogen bonding." Initially some active groups of the molecule attach themselves to the solids with a large portion of the molecule extending into the solution. Two particles can become tied together by long flocculant molecules in the following ways—by bonding between the active groups of two flocculant molecules on different particles, or by an extended molecule from one particle attaching itself directly to the surface of the other particles." These flocculant bridges prevent the particles from moving apart through random motion, but when such motion moves them together other active groups on the flocculant bridge bond to the solids, holding them in the closer position. This process is repeated until the particles are close together. Although bridging is probably a major flocculation mechanism, it is not the only phenomenon involved. Relatively neutral acrylamide flocculants reduce the magnitude of the zeta potential by increasing the viscosity of solution in the immediate vicinity of the solid surface which contains the mobile counter ions of the double layer. In other words, it moves the shear surface which bounds the zeta potential out into the solution containing counter ions which tend to neutralize the zeta potential. This effect is probably more pronounced during the initial adsorption period, before the flocculant molecules are pulled close to the solid. In some cases the slight charge of the polyacry-lamide molecule tends to neutralize a zeta potential. However, this is not a primary flocculation mechanism, as evidenced by the fact that the polyacrylamides will flocculate solids with either positive or negative zeta potential. Adsorption of polyacrylamide flocculants by a solid is substantially an irreversible reaction. Since the flocculant molecule is attached to the particle surface by many active groups of high bonding strength, desorption would require the simultaneous breaking of many bonds—an unlikely occurrence. UNIQUE PROPERTIES The irreversible adsorption of certain polyacrylamides, the flocculant's high affinity for solid surfaces and its rapid adsorption make it effective, but these unique properties require special techniques to achieve maximum flocculation. If flocculants of this type are added to a pulp as a relatively concentrated solution, the solids in the

Jan 1, 1960

By Richard R. Bains

"When l hear - I normally remember 10 percent When I hear and see - I can remember 15 to 25 percent When I hear, see, and do - I usually remember up to 50 percent" While this is not a truism in relation to each and every individual; on the average, this is the case. If we use this as a premise in training operator and maintenance personnel, then it must be obvious that we can't rely on a mere presentation, even one which includes the needed classroom participation and/or hands on work, to do a thorough job and to make this personnel totally proficient - 100 percent proficient. We have to have some other device some other means to make this a continuing process, a process wherein the people can grow in knowledge while performing their normal duties. We have to feel that the words "normal duties" are the key to the whole program. If you would ask a crusher operator what his duty is, he might say "To run this crusher so that we produce 250 tons per hour of a minus 13mm (minus 1/2 ") product." A maintenance man could say "To fix the unit when there is a problem." Both of these answers are legitimate but, they are only a part of the total picture. In order for each of these individuals to do the best job, he must know not just the specifics about the machine he works with or on - he must know the interrelation of all the machinery in the crushing circuit - how the efficiency of each machine affects the others - why a minor problem on one piece of equipment can generate a major problem for another unit which follows it or precedes it. In short, you cannot separate machine operation and maintenance from the application of the equipment in the crushing circuit - and obtaining this knowledge must be a part of the normal duty of crushing plant personnel. As an example a crusher - any crusher - is designed to crush oversize material. It is not designed to accept feed which is already at or less than the required product size. If sized material goes to the crusher, increase wear results by using the crusher as a chute or the crushing chamber can be clogged up with the fines. This latter point is particularly true with cone crushers, especially in the third (Short Head) stage of crushing. When a Gyradisc is used (fourth stage crushing) it is even more critical that the product be removed before the material goes to the crusher. The crusher cannot control this - the screen ahead of the crusher does. The screen must be of adequate size and be functioning properly to allow the crusher to work at optimum. Screening is both an art and a science. Since there are so many variables which affect the output of the screen, it is always best to have a screen which is larger than the sizing calculations dictate. The screens are the most important elements in the circuit. Without screens, specification materials cannot be made and the size of the screen will ultimately aid or hinder your ability to get the most production possible out of the plant. There is a formula available from all screen manufacturers which is designed to calculate the proper screen size. It takes into consideration the

Jan 1, 1982

By D. H. Gray, G. Bergamini, I. Fatt

A method developed by soil scientists for measuring permeability anisotropy of soils has been adapted for use in studies of sandstone permeability aniso-tmpy. Studies on Berea and Bandera sandstone show that permeability of these materials decreases upon application of simulated overburden pressure. Permeability reduction of Berea and Grubb sandstone cores subjected to simulated overburden pressure is shown to be a function of the ratio of radial to axial stress. INTRODUCTION The effects of mechanical stress on reservoir rock parameters are now generally accepted as being important in reservoir engineering calculations. In several oil fields the unique behavior of the reservoir has been attributed to the influence of overburden pressure or internal fluid pressure on rock permeability or fluid content. l Although the gross effects of overburden pressure on permeability, porosity, waterflood efficiency, electrical resistance and sonic velocity have now been established,3-9 there are some very interesting, and perhaps important, details of rock behavior under stress that have not heretofore been studied. In this paper we will show that permeability anistropy of several sandstones is a function of overburden pressure. We will also show that permeability reduction of cylindrical samples of two sandstones, when subjected to mechanical stress, is a function of the ratio of radial to axial stress. Most studies of overburden pressure effects made in the past have attempted to duplicate reservoir conditions by applying hydrostatic external pressure on all surfaces of the sample. Assuming perfect elasticity, that is, no viscoelastic flow during geological time, reservoir rock in situ cannot be under hydrostatic stress as is apparent from the value of 0.25 for Poisson's ratio for most rock. In the absence of tectonic forces the horizontal stress component If there are directional permeability effects, as has been reported from field and laboratory studies, l0,11 then one would expect hydrostatic stress as used in the laboratory to give a different permeability reduction from that occurring under reservoir stress conditions. The influence of stress on directional permeability was measured by a modification of the method first described by Maasland and Kirkham for use on soil samples.12 Their method permits calculation of the permeabilities along each of the three mutually perpendicular axes of a cubic sample. The modification reported in this paper extends the method to observing these permeabilities when the sample is under hydrostatic stress. The Hassler sleeve type of core holder is satisfactory for studying overburden pressure effects on permeability if a known force is applied to the end plugs. Wyble6 used a sleeve core holder but did not load the end plugs. In this paper we combine sleeve pressure and axial force to give permeability changes which we believe are close to those occurring in reservoirs when reservoir pressure changes. The combination of sleeve pressure and axial force assumes, however, that the sleeve pressure simulates both vertical stress and horizontal stress in one direction. METHOD PERMEABILITY ANISOTROPY The Maasland and Kirkhaml2 method of measuring permeability anisotropy uses a cube of porous material which is Open On three faces and has discs with a Center hole for an air inlet cemented to the other three mutually perpendicular faces (Fig. 1). The rate at which air pressure falls in a bottle of known volume, and pressure slightly above atmospheric, when the bottle discharges through each disc, is

By G. Thodos, R. B. Grieves

A method has been developed For predicting the critical temperatures and critical pressures of binary mixtures of carbon dioxide, hydrogen sulfide, nitrogen, hydrogen, carbon monoxide and oxygen with the normal paraffin hydrocarbons. For carbon-dioxide and hydrogen-sulfide systems, relations are presented that take into account the peculiar behavior of mixtures with closely boiling components, such as carbon dioxide-ethane and hydrogen sulfide-propane mixtures which exhibit minimum critical temperature points. For hydrogen, nitrogen and carbon-monoxide systems, the extreme critical behavior caused by wide differences in pure component properties is established In addition, those fixed gas-paraffin systems which resemble paraffin-paraffin systems are also accounted for. For a mixture of known composition, the pure component critical temperatures, critical pressures and normal boiling points are all that are required to determine its critical point. Graphical relations are presented relating Tc and PC , of the mixture to the pure component properties. From the treatment of 12 carbon-dioxide and hydrogen-sulfide systems reported in the literature (74 mixtures), the expected error lor the critical temperature is approximately 1.5 per cent, and for the critical pressure, approximately 2 per cent. From the treatment of six hydrogen, nitrogen and carbon-monoxide systems reported in the literature (30 mixtures), the expected error for both the critical temperature and critical pressure is approximately 2.5 per cent. The relationships, which have been developed with only normal paraffins as the hydrocarbon components, may be extended to those isoparaffins and olefins which fall within the allowable volatility ranges. INTRODUCTION Many of the fixed gases — carbon dioxide, hydrogen sulfide, nitrogen, hydrogen, carbon monoxide and oxygen — occur in natural mixtures with hydrocarbons. Carbon dioxide and hydrogen sulfide are frequent components of the fluids produced from underground petroleum reservoirs. Nitrogen, carbon dioxide and hydrogen sulfide are present in varying quantities in most natural gases and gas-condensate well effluents. Hydrogen mixtures are of considerable interest in many phases of refining processes of petroleum. The determination of the critical temperatures and critical pressures of such mixtures is of value in vapor-liquid equilibrium studies, for the prediction of the characteristics of underground reservoirs, and for reduced-state correlations of PVT, transport and thermodynamic properties. The accurate estimation of the critical point for binary mixtures is an important initial step toward a complete analysis for the establishment of the critical temperatures and pressures of multi-component mixtures. Methods for predicting the critical temperatures and critical pressures of binary hydrocarbon systems have already been presented in the literature.8 It is possible to apply these existing methods to fixed gas-paraffin mixtures, but due to their unusual critical behavior, values calculated deviate considerably from experimental values. For systems containing trace quantities of the fixed gases, these methods are acceptable; however, for systems containing more than 5 mol per cent of the fixed gases, these utterly fail to produce reasonable critical values. Consequently, in this study a method has been developed for handling such binary mixtures over the entire composition range. CARBON-DIOXIDE AND HYDROGEN-SULFIDE SYSTEMS The critical behavior and the vapor pressure behavior of mixtures of carbon dioxide and hydrogen sulfide with paraffinic hydrocarbons may be quite similar or quite dissimilar to that of paraffin-paraffin mixtures, depending on the volatilities of the components involved. The critical temperature and normal boiling point of carbon dioxide are very close to the corresponding values for ethane, while its critical pressure is considerably higher than that of ethane. The normal boiling point of

By Jei Y. Choi, P. G. Shewmon

Using a scratch smoothing technique, the magnitude and the ratio of the surface diffusion coefficients (D,) in two orthogonal directions have been measured on copper for over 100 different surface orientations. Anisotropy was found for all surface orientations except those lying near the (100) and (111); however, these anisotropies were rarely greater than 2.0. The direction of maximum D, appears to coincide with the direction of step edges on any given surface, and if no such steps exist, no anisotropy is found. Thus the jump frequency along a step edge is shown to be faster than the frequency of a jump over the step. The values of Ds and AH for the (100) and the (111) orientations agree quite well with those obtained earlier by the grain boundary grooving technique. It is proven that the directions of maximum and minimum D, (the principal axes) for any surface orientation are known if the perfectly ordered plane corresponding to the given surface orientation possesses a plane of mirror symmetry. Thus the principal axes of D, for orientations lying along the sides of the unit stereo-graphic triangle are always known independent of the extent of thermal disorder or impurity adsorption. The merits and shortcomings of King and Mullins' recently published equations relating Ds to the rate of scratch smoothing are discussed. 1N an earlier paper the authors have reported the variation of the surface diffusion coefficient (Ds) with surface orientation on copper.' In that study Ds was determined from the rate of growth of grain boundary grooves on symmetric bicrystals. This gave values of Ds from 850° to 1070°C in a given direction on each of the six surfaces. It was found that the activation energy for surface diffusion was essentially the same for all six surfaces. The theory developed to explain these data assumed that the free energy of any given type of surface site depends only on the number of nearest neighbors the atom has. This same theory predicted that on any given surface Ds should be independent of direction. The primary aim of this study was to check the validity of this prediction for a wide range of surface orientations on copper. The growth of grain boundary grooves is ideal for studying Ds in a given direction on a given surface over a range of temperatures, because the same specimen can be repolished and used again. However, there is considerable work involved in growing a symmetric bicrystal, and for a survey of Ds in two or more directions on many surface orientations, the technique would be arduous. A better technique appeared to be the scratch method used primarily by Mykura. 2 If a scratch is placed in a surface whose surface tension is independent of orientation, the surface will smooth out in time under the influence of surface tension. To determine D, from this flattening, Blakely and Mykura2 used an approximate solution which was assumed to describe the rate of flattening. Recently King and Mullins3 (hereinafter K and M) have given a more exact analysis of the flattening of an isolated scratch. A second aim of this paper was to check the validity of this newer analysis and compare the values of Ds determined thereby with the values obtained from grain boundary grooving techniques. EXPERIMENTAL PROCEDURE In an effort to work with a particular predetermined surface orientation, light orthogonal scratches

Jan 1, 1963