Search Documents

By M. H. Gaskell, D. C. Lindley

Small, steeply inclined reservoirs without natural water drives often are found associated with salt domes or other highly faulted structures. Frequently, only one well may be economically justified in these reservoirs, from which oil is produced by an expanding gas-cap drive or by a dissolved-gas drive. Although a large fraction of the oil upstructure from the well may be recovered during primary depletion, only a small fraction of the downdip oil can be produced because of gravity effects. This downdip oil has been defined as cellar oil991 in contradistinction to "attic oil" which is the oil above the structurally highest well in reservoirs where a natural water drive is present. In this study, two methods of producing cellar oil by water flooding a one-well reservoir were investigated by means of a laboratory model. This model was scaled to represent a prototype reservoir having an area of 30 acres, a permeability of 500 md, and a thickness and dip of 30 ft and 30°, respectively. One method considered, the simultaneous injection of water and production of oil from a single well, would require that the lower portion of the productive interval of a well be completed for water injection and the upper portion for oil production. The other method considered, intermittent injection, would involve alternate injection of water into and production of oil from a single well. Injection of water into the formation would repressure the reservoir, causing gas to go back into solution. Since some of the injected water would flow updip from the well, water injection usually would be followed by a waiting period during which the water could drain from above the wellbore. Production of oil by gravity drainage and gas-cap drive could be initiated when water drainage became sufficiently complete. The amount of water produced along with the oil would naturally depend on how soon after water injection ceased that production was started. This process could be repeated in cycles until oil could no longer be produced economically. Of these two methods, the intermittent injection technique would be simpler to put into operation since it does not require a dual completion. Also, it is probably more generally applicable than the simultaneous injection-production method. It is to be expected that in some reservoirs the rock and fluid properties would be such that practical oil-production rates could not be achieved by the simultaneous technique. However, in reservoirs where the simultaneous method will result in practical rates of oil production, it does have the advantage of permitting immediate, continuous oil production; whereas in the intermittent method, oil production is interrupted by periods of water injection and drainage. It was the objective of this study to determine whether these two methods of cellar oil production are practical for the representative prototype investigated and to evaluate their relative merits. DESIGN OF LABORATORY MODEL SCALING REQUIREMENTS The prototype reservoir and fluids were selected to have the dimensions and physical properties shown in Table 1. The laboratory model was then designed in accordance with well known scaling criteria, as discussed by Croes, et al,2 except for one modification. According to Croes, et al, one requirement of scaling a laboratory model to a reservoir prototype is that both the relative permeabilities and dimensionless capillary pressure be the same functions of water saturation for the model and the prototype. Since unconsolidated sand packs are used in the laboratory model to represent the consolidated porous media of the prototype, it is virtually impossible to satisfy this requirement. Much of the difficulty stems from the fact that unconsolidated sands usually exhibit lower residual oil and connate-water saturations than do reservoir rocks. To satisfy the scaling requirement as nearly as possible, Perkins and Collins' have suggested that the relative permeabilities be re-defined as

By A. S. Michaels, M. C. Porter, A. Stancell

Previous laboratory studies have demonstrated that the injection of small quantities of reverse wetting agents during water displacement can increase oil recovery from unconsolidated porous media.9 In the present investigation, an attempt has been made to determine more fully the effects of reverse wetting treatments and to clarify the mechanism by which increased oil recovery is effected. Water-oil displacements were performed in beds of 140-200 mesh silica sand. Hexylamine slugs (injected after 0.25 pore volume of water throughput), when adequate in size and concentration, were effective in promoting additional oil recovery. Their effectiveness increased with the quantity of amine injected. However, slugs of sufficient size and concentration to stimulate oil production at water flow rates of 34 ft/day did not do so at 4 ft/day. Visual studies in a glass grid micromodel have shown that the stimulation of oil production, via ayueous hexylamine, is a result of transient changes in the oil wettability of the pore walls. if the amine slug is of sufficient size and concentration to induce significant changes in the adhesion-tension, large continuous oil masses will be formed. if the superficial water velocity is high enough to result in rapid desorption of the amine, a favorable "wettobility gradient" may be established across the masses; under such conditions, high oil mobility is observed, and increased oil recovery results. INTRODUCTION It is generally agreed that the efficiency of oil displacement by water in porous media is limited in part by capillary forces which cause the retention of isolated masses of oil — resulting in the so-called "irreducible minimum oil saturation". Recent estimates10 indicate that there are about 220 billion bbl of petroleum in United States reservoirs which are not economically recoverable with present techniques (such as water flooding). This amounts to almost five times the known recoverable reserves. It has been recognized for some time that a suitable alteration in the water-oil interfacial tension and/or the contact angle, as measured between the water-oil interface and the solid surface, should result in better displacement efficiency. Surface active agents can be used as interfacial tension depressants to accomplish this objective,1,2,7 but unfortunately, the additional oil recovery is seldom commensurate with the treatment cost. In contrast to interfacial tension depressants, the effect of contact angle alterations on water-oil displacements has received relatively little attention in the literature. It is known that the wettability affects the displacement process.3,4,11 Displacements in water-wet systems generally result in lower residual oil saturations than those in oil-wet systems. The effect of "'transient" wettability alterations concurrent with the displacement process have been investigated by Wagner, Leach and coworkers,4,11 wherein it has been demonstrated that the establishment of water-wet conditions during water flooding of oil-wet, oil-saturated porous media is accompanied by significant increase in oil displacement efficiency. Michaels and Timminss studied the effects of transient contact angle alterations resulting from chromatographic transport of reverse wetting agents through unconsolidated sand. It was demonstrated that chromatographic transport of short-chain (C4 through C8) primary aliphatic amines can improve oil recovery and that the recovery increases with the quantity of amine injected (i.e., with either the amine concentration or the volume of the slug injected). Circumstantial evidence indicated that the increased displacement efficiency resulted primarily from transient changes in wettability of the porous medium. In the Present investigation. additional information has been obtained on the effects of reverse wetting treatments and the mechanism by which increased oil recovery is accomplished. Hexylamine slugs of varying size and concentration were chromato-

Jan 1, 1965

By Arthur H. Wilson

INTRODUCTION The stratified deposits of the coal measures are strongly laminated and exhibit a high degree of anisotropy. The stronger rocks in the sequence possess joints and shear planes, the coal itself has a closely spaced cleat pattern, and the softer rocks are capable of flowage. To calculate the general distribution of stress in such a medium by analytical means based on the theories of elasticity is difficult, and has not yet been satisfactorily achieved. Nevertheless, some estimate is required to aid the design of supporting pillars and permit the correct siting of main roadways. This is important when laying out districts for longwall extraction, particularly if the results of previous experience are not available in the area to be exploited. Although elastic stress analyses, including finite element analysis, may not be very appropriate, the basic equilibrium conditions will apply. These, combined with logical deductions based on observed fact, can be used to give appropriate solutions which experience has shown to be capable of giving acceptable results in the design of pillars associated with longwall workings. Constancy of cover load is one of the fundamental equilibrium conditions. When mining below ground, the cover is not removed, therefore the average vertical load after mining must equal the initial cover load. If mining produces a local decrease in load in any particular area, it must be balanced by an equivalent increase in load nearby. Bending moments in the strata above are capable of compensating for the turning moments which this redistribution of load may produce, and the existence of a "rear abutment", much discussed between 1950 and 1960, is not an essential equilibrium requirement. If the distribution of vertical stress is plotted three-dimensionally, then the load on any small element of area 6S will be o.6S, where o is the average stress. This also represents the volume of the "stress envelope" which lies above 6s. By making the individual areas very small and summing together, it is possible to show that the total load on any particular area can be found by calculating the volume of the stress distribution envelope which lies above it. A similar consideration applies to the stress distribution in a two-dimensional situation. If the stress distribution curve is drawn, then the area below any portion will represent the load per unit depth of section. For example, Figure 1 represents the possible stress distribution across a caved waste and associated ribside. If AW is the load deficiency [ ] These loads must balance, therefore area AW = AS, and if one can be deduced, the other will then be known. Attempts have been made to measure stress distributions in the ribside and in the waste. Stress meters in soft rocks such as the coal measures have not proved very effective. Those based on the measurement of strain have experienced difficulty in strata capable of flowage, high modulus stress meters suffer from cross sensitivity, and overcoming to obtain absolute stress is almost impossible. Load measuring instruments left in the waste have also proved largely ineffective, mainly as a result of the difficulties of protecting the leads in a caving environment. Certain logical deductions, however, can be made about the conditions in the waste. CONDITIONS IN THE WASTE Over the area of the waste the surface trough which develops is remarkably consistent, despite the geological variations which occur from coalfield to coalfield. In Britain, an accuracy of 210% is claimed for subsidence prediction based on width of extraction and depth of cover (National Coal Board, 1975). The subsidence in the USA is more variable (Adamek and Jeran, 1981), particularly with respect to the point of inflexion, but the same general pattern occurs. At the shallower depths the somewhat harder roof strata involved in the caving in the USA may suffer less compaction, giving reduced values of subsidence. Subsidence at intermediate horizons below the surface

Jan 1, 1982

By Donald A. Corrigan, John Chipman

It is shown that the heat of solution of nitrogen in liquid-iron alloys is Proportional to the interaction coefficient. This proportionality forms the basis for a method of predicting nilrogen solubility at any temperature when the interaction coefficient is knoun at 1600°C ov when the solubility is known at some one temperature. A method for predicting the solubility of nitrogen in liquid steels, including alloy steels, was proposed some years ago by Langenberg.' Since the data available at that time were restricted to temperatures of about 1600°C, his predictions were similarly restricted. More recently, Nelssonz devised an approximate method for estimating nitrogen solubilities at higher temperatures. It is the purpose of the present paper to present a method by which the solubility of nitrogen at any temperature within the steelmaking range may be predicted from the known interaction coefficients at 1600°C. Nitrogen in iron and in all of the alloys to be considered here is known to obey Sieverts' Law; hence the activity of nitrogen in an alloy of fixed composition is proportional to its concentration, here expressed in weight percent. The activity of nitrogen is defined as equal to its weight percent in the binary Fe-N solution at any temperature. Its activity coefficient in any alloy is the comparison being made at equal values of T and PN2. In all alloys the activity coefficient changes with composition, log fN being a linear function of the percent of alloying element at low concentrations. In the following calculations the alloy compositions are restricted to those in which this linear relation is exhibited. For most systems this is a fairly wide range, for example up to 5 pct V and to 10 pct Cr or Ni. For this composition range. complex alloy is the same as that in the Fe-N-j ternary solution. Langenberg's method of prediction was based on Eq. [3], the values of log fN for various additions being taken from a graph. Instead of using the simple addition indicated in Eq. [3], he used a more complex method suggested for Fe-S-j alloys by Morris and Buehl.3 For the composition ranges in which Eq. [2] is valid the two methods are equivalent. Nelson extended the prediction to other temperatures on the assumption that logfN is inversely proportional to absolute temperature. It may be shown that inverse proportionality would result if the partial molal entropy of nitrogen were unaffected by addition of the alloy element, an assumption which Nelson designated as a "regular" solution. It has been shown recently by the authors4 that this assumption is not a good approximation. The heat of solution of nitrogen (N2) in an alloy may be obtained if the solubility is known as a function of temperature. Measurements of this nature have been reported recently by Beer5 for Fe-Mn alloys, by Nelsson2 for Fe-C, by El Tayeb and parlee6 for Fe-V, and by Pehlke and Elliott7 for many alloys embracing a wide range of compositions. In connection with the work of the last named authors it is noted that their Fig. 22 gives the heat effect per half mole rather than per mole of N2. In using their data we have shifted some of their values slightly by using the best straight line in preference to their curve. Their data, supplemented by others from the literature, are summarized in Table I. In Fig. 1 the heat of solution of nitrogen is shown as a function of composition for the several alloy systems. The difference between the heat effect in the alloy. AH; and that in pure

Jan 1, 1965

By J. R. Dawson, J. A. Glunt

VESTA No. 4 and 5 mines supply most of the high volatile coal required for Jones & Laughlin's byproduct coke plants. Until 1944 all coal produced in these mines was loaded by hand. Pressure to mechanize at Vesta was brought on by the manpower shortage in World War 11, and in 1943 a decision was made to change to mechanical loading. It was the opinion of those concerned that by use of selective mining the coal would be clean enough to be processed by the existing preparation plants. At that time coal cleaning at Jones & Laughlin consisted of hand picking the larger sizes at the mine tipples and wet washing at plants located at the Pittsburgh and Aliquippa Works. A typical section of the Pittsburgh seam as it occurs at Vesta is shown in Fig. 1. The 14 to 16 in. of drawslate immediately over the coal is too soft to be used for roof and must be taken down, leaving the rooster coal just above for roof. In selective mining an attempt is made to mine the coal under the drawslate first and then load out the drawslate separately as refuse. In full seam mining slate and coal are shot down at the same time and loaded out. Mechanical loading at Vesta created new problems. It was found that selective mining, even when carefully applied, increased the refuse in the raw coal to such an extent that the washers at the mills were unable to handle it. Large tonnages of refuse were being transported, a reject disposal problem was created, and good metallurgical coal was being loaded out and lost. In addition, the selective method handicapped operation of the loading machines. Fig. 2 shows how the ash content of the raw coal increased as mechanization proceeded at No. 5 mine. New Preparation Plant: After an exhaustive study of this situation by J & L management, is was decided that a preparation plant should be constructed at the mines, capable of handling full seam mined coal and large enough to process full production of both No. 4 and No. 5 mines. It was decided that from the standpoint of inside operation and haulage the new plant should be located as near as possible to the old No. 5 tipple on the Monongahela River near Vestaburg. Full seam mining at Vesta could be expected to produce a tremendous volume of refuse along with the coal, since 14 to 16 in. of slate would be mined with an average 78 in. of coal. Disposal of this refuse required serious consideration in selecting a plant site. The only area near Vestaburg large enough for disposal of the plant refuse was across the Monongahela River at LaBelle. Ample space was available here, and construction at this location would not interfere with operation at the No. 5 tipple. It had been noted over the years that the sulfur content of the coal produced at Vesta was gradually increasing, and there was every indication that this increase could be expected to continue as the mines developed further from the river. It was decided to construct a three-part separation plant with complete blending facilities to produce both metallurgical and steam coal. In this system an attempt is made to reduce the sulfur in the metallurgical coal in a secondary cleaning process. Construction of the new preparation plant got under way early in 1947 and continued until the spring of 1950. The plant was designed to handle 2400 tph of raw coal containing 30 to 35 pct refuse. Cost of outside buildings and equipment was about $14 million. Total cost of the plant, together with improvements and changes made at this time, was approximately $21 million.

Jan 1, 1957

By R. Sporcic, P. J. Mudra

During the past year personnel of the Roof Control Research Group of the Bureau of Mines designed and developed encapsulated hydraulic cells for measuring pressure changes in coal in situ. Preliminary results from feasibility tests in progress in the laboratory and field indicate that the cells respond favorably to changes in pressures associated with a coal-mining environment. The ultimate objective is to use these cells to obtain engineering information relating to coal bump or coal outburst phenomena. Mining research has experienced a remarkable growth during the past decade and from all indications should surge forward at even a greater pace in the future. This increased interest in mining research has been brought about by the ever-multiplying number of technical problems being encountered by the mining industry in its effort to produce pay-dirt tonnages safely and economically from greater underground and surface pit depths. Among the various divisions in the field of mining research, the study of ground stress has received a large part of the overall attention. Numerous technical papers have been written with regard to ground stress conditions around mine openings and yet the total usable knowledge concerning this subject is extremely limited. Research teams around the world are endeavoring to bridge the gap between theoretical and laboratory approaches and the solution to design problems in the field. The problem of ground stress is not a new one for the coal mining industry. Operators in both eastern and western coal fields of the United States as well as in many foreign countries have long been plagued with a number of ground stress problems, one of which is commonly referred to as the coal-mine bump. This term or phenomenon has been aptly defined by earlier investigators as the violent and sudden failure of coal and adjacent rock. Direct results of such failures have been the loss of human lives and thou- sands upon thousands of dollars of sustained mine damages. In an effort to alleviate the magnitude and frequency of these failures, mine operators have employed and are presently employing various corrective techniques. These include: Inducing failure in heavily stressed areas by augering large-diameter holes into stressed pillars, using extensively yield-able steel arches in both long-term haulage and short-term face entries, backfilling unused or abandoned entries with mine waste to gain additional support, and using systematic pillar coal panel extraction techniques including mechanized longwall mining. The Health and Safety Activity of the Bureau of Mines has for a number of years contributed considerable time, funds, and talent in an effort to define better the ground stress problems associated with coal-mine bumps. As a part of this investigative program, in situ ground pressures are presently being studied in coal mines located in West Virginia and Utah. The description and development of the device being used to measure these pressures is the specific topic of this paper. CHOICE OF INSTRUMENTATION After consideration and evaluation of the various instruments and techniques that are being used by researchers in the field of rock mechanics to detetmine in situ stresses, a simple hydraulic system was selected for detailed investigation. Aside from simplicity, a hydraulic system is relatively inexpensive and also eliminates the need for electricity in its installation and operation. The hydraulic device referred to is, in essence, a simple unidirectional pressure-measuring cell. Hydraulic cells, which had been used for measurement of pressures in hard rock, were investigated but found not entirely suitable for use in coal, particularly since they involved (1) preparation and emplacement of cement grout at the test site, and (2) a waiting period before the cells became operational. At the outset, it was decided that certain design parameters be established. The cell should be simple and inexpensive, constructed of materials readily obtainable and easily built in the laboratory or field by unskilled labor. It was further decided that it was desirable to encapsulate the cell in a suitable mate-

Jan 1, 1963

By A. S. McLatchie, R. A. Hemstock, J. W. Young

Much attention has been given in the past few years to methods of increasing the recovery of oil from proven reserves. Numerous laboratories have made investigations to evaluate the possibilities of increased oil recovery by high-pressure injection of dry gas, injection of a propane slug followed by dry gas, solvent flooding. and by the injection at relatively low pressures of gases enriched with ethane and propane. Several years ago, Whorton and Kie-schnick' published the results of laboratory studies on high-pressure gas injection which showed that, in the case of light oils, recoveries could be considerably increased by sweeping the reservoir with dry gas at pressures in excess of 3,000 psig. The increase was attributed by those authors to the vaporization of oil at the invading gas front and viscosity and solubility effects produced at the front by the invading gas. Later, Stone and Crump' presented the results of a series of displacement experiments in which a light under-saturated crude oil was displaced from sand-packed columns with unusually high recoveries when the displacing gas was a rich condensate or a dry gas enriched with ethane or propane. They also conducted similar experiments at higher pressure on heavy undersa tu rated crude oil, although in this case the increase in recovery was not as great as in the case of the light oils. In both cases, viscosity reduction and swelling of the by-passed oil behind the invading gas front were believed to be responsible for the more favorable recovery of the original oil in place. Within the past year, other investigators", ' have presented the results of laboratory studies of miscible slug and solvent flooding recovery processes. This paper describes the laboratory methods developed for evaluating benefits to be obtained by enriched gas drive in specific reservoirs, and presents the results of several displacements of crude oils which possess a wide range of physical properties. The displacements were conducted at reservoir conditions of temperature and pressure. The apparatus used in the following experiments consisted of a sand-packed tube which served as the model reservoir, a cylinder of injection fluid, and a mercury pump. The stainless steel tube, 8 ft long and 0.53 in. I- was packed with a graded quartz sand. The high-pressure pump discharged mercury into the bottom of the injection fluid cylinder at a constant rate as low as 1 cc/hr. The average porosity and permeability of the sand column were 34.6 per cent and 3.25 darcies, respectively. In each case the tube was charged by the displacement of salt water by the reservoir oil under consideration. Recently a project was initiated to evaluate oil recovery by enriched gas drive from three oil reservoirs. Samples from a fourth reservoir (in this case high-viscosity oil) were studied with a view to obtaining recovery information of general applicability to low-grade, high-viscosity crudes. The oils from these four reservoirs exhibited a wide range of physical properties, and the reservoir conditions of pressure and temperature simulated in the laboratory represented several typical field conditions under which enriched gas drive might be employed. One of the reservoirs selected for laboratory displacement experiments produced an intermediate-gravity crude (29.6" API) by solution gas drive and a weak water drive. A low recovery in the range of 10 to 20 per cent was anticipated. Four displacement experiments were made to determine the effect of injection gas composition and initial gas saturation upon recovery of oil from the laboratory model. Two types of reservoir oil were used in these experiments. In the first run, a desaturated crude with a bubble point of 395 psi was charged to the tube. In the three subsequent runs, a simulated original reservoir oil was charged at 2,000 psi and produced by solution gas drive to 300 psi before beginning gas injec-

By Robert C. Emmett, Donald A. Dahlstrom

FOR many years gravitational classification has been employed as a basic tool in beneficiation of minerals and coal. While improvements have been made to increase efficiency and fields of application, the basic flow pattern has remained relatively unchanged in most gravitational classifiers. Feed slurry is introduced into a settling pool wherein the coarser solids settle against either an upward or horizontal fluid current, or a combination of both, and are withdrawn in a concentrated underflow stream. The finer solids below the classification point possess too low a settling velocity and thus are primarily swept out through a weir overflow by the bulk of the fluid. Because of its simplicity, efficiency, and low power and maintenance costs, gravitational classification finds a wide acceptance for separations in the range of 20 to 325 mesh. Two factors resulting from the basic flow pattern employed in gravitational classification present difficult problems for certain installations. If classification at 60 to 200 mesh of separation is desired, capacity in terms of gallons of overflow per minute per square foot of settling pool area must be low to allow required solids to settle to the underflow. If a thousand or more gal per min of feed slurry must be handled, either a very large classifier or a number of smaller units must be employed, taking up floor space and head room. Examples of this are the large classifiers, wetting tanks, or settling tanks used in the coal industry for recovery of process water from fine solids. Units as large as 50 or 60 ft in diam and 60 ft high, requiring substantial amounts of steel, are not uncommon. A second factor is the lack of self-regulation in gravitational classification. As overflow rate increases, mesh of separation increases correspond-ingly. This normally heightens difficulties of bene-ficiation. If a fine mesh of separation is required at varying feed rates, the problem is more than doubled in complexity. One of the primary advantages of gravitational classification is low power requirement. Gravity feeds or very low pressure heads are employed. However, fluid energy is still present in the inlet stream and provision must be made to dissipate it properly to obtain uniform upward or horizontal currents. Rather than waste this energy, it would be desirable to utilize it to secure a greater degree of self-regulation and simultaneously increase classification capacity per square foot of area. A free vortex could be realized by a tangential entry of feed, resulting in generation of centrifugal force to complement force of gravity in its action. With greater force it should be possible to gain finer separation at any overflow rate per square foot of settling pool area as compared with conventional gravitational classification. Furthermore, as feed rate increases, centrifugal force will also increase and at least partially offset faster currents sweeping solid particles to the overflow. A more stable classification point should result. The liquid-solid cyclone is the most common application of a free vortex in the beneficiation field.' Many previous papers have emphasized uniformity of flow pattern within the cyclone which is largely responsible for the sharp classification that can be obtained.'-4 If a free vortex can be maintained in a non-pressurized vessel with a free surface it may be possible to realize a third advantage of sharper classification. This open-top cyclone would then achieve a minimum energy loss comparable to that with conventional classifiers, and a mesh of separation coarser than 150 mesh, extending the range of application of the free vortex. This is not presently possible with ordinary cyclones. To test the applicability of the free vortex to gravitational classification, a 30-in. diameter open-top cyclone was constructed at Northwestern University. The cylindrical section was 30 in. high and the conical section included an angle of 60". The feed nozzle was a standard 4-in. pipe entering tan-gentially, with centerline 17 1/2 in. below the top of the cyclone. The conical section was flanged near

Jan 1, 1954

By M. Prats

The effect of a sand-filled vertical fracture of limited radial extent and finite capacity (fracture capacity is the product of the permeability and width of the fracture) on the flow behavior of a cylindrical reservoir producing an incompressible fluid through a centrally located well has been investigated mathematically. The shape of the lines of equal pressure near the fracture is essentially independent of the size of the reservoir, provided that the field radius is of the order of the fracture length or larger. For reasonable values of production rates and of fluid, reservoir and fracture properties, the total pressure drop between the end of the fracture and the well is gelrerally negligible compared with the pressure drop in the reservoir. With regard to production response, the effect of vertical fractures can be represented by the production response of an equivalent or effective well radius. For a high-capacity fracture, the effective well radius is a quarter of the total fracture length, decreasing with the fracture capacity. When invasion effects are simulated by decreasing the width of the damaged zone with distance from the well, the effect of formation damage around a fracture on the production response is not so seriolls as indicated by the literature. This suggests that frac fluids with a conventional filter-loss response are better than high-spurt-loss frac fluids, provided the effective permeability of the damaged zone is the same. INTRODUCTION This paper considers the effect of the fracture capacity, as well as the formation damage which can result from fracture treatments, on the productive capacity of vertically fractured wells. Other publications, notably those of van Poollen,l,2 consider these same effects. In addition to providing more general results for vertical fractures than are available from the liter- ature, the present paper gives the equivalent well radius of fractures having different lengths and capacities and, also, includes pressure distributions in and around the fractures. The effect of a damaged zone around a fracture on the production response was not found to be so great as that reported by van Poollen. 2 This difference probably stems from the fact that we consider a damaged zone which is widest (but is still small) near the well and thins out toward the extremities of the fracture, whereas van Poollen considers a damaged zone having a uniform width for the entire fracture length. Simple, but adequate, equations which describe the effect of these variables on production response are presented (in Appendixes A and B). Thus, results can easily be extended to values of the variables not specifically considered here. IDEALIZATION AND DESCRIPTION OF THE FRACTURED SYSTEM It is assumed that a horizontal oil-producing layer of constant thickness and of uniform porosity and permeability is bounded above and below by impermeable strata. The liquid is incompressible. It is assumed that, after the well is fractured, the cylindrical outer "boundary" is at a uniform potential, provided that it is not too near the fracture. The fracture system is represented by a single, plane, vertical fracture of limited radial extent, bounded by the impermeable matrix above and below the producing layer (reservoir).3 Fig. 1 indicates the general three-dimensional geometry of the fractured reservoir described above. If gravity effects are neglected, the flaw behavior in the reservoir will be independent of the vertical position ill the oil sand. This means that the flow behavior in the fractured reservoir can be described by the two-dimensional flow behavior shown in the horizontal cross section of the reservoir, Fig. 2. PARAMETERS The effect of a fracture on the pressure distribution in the fracture itself and in an otherwise undamaged (no skin) reservoir indicates that the pressure distribution is a function of three parameters.

By C. Chu

A theoretical investigation has been made of the forward combustion process using a one-dimensional linear mathematical model, taking into consideration the effect of the vaporization-condensation which occurs on the leading edge of the heat wave. This work involves the solution of five coupled partial differential equations. Besides the vaporization-condensation phenomenon, these equations account for conduction, convection, combustion, heat loss, diffusion and bulk fluid flow. For the one-dimensional linear model studied, the vaporization-condensation phenomenon does not induce appreciable change in the temperature at the combustion front; and its primary effect is to create a steam plateau and to increase the length of the heated zone ahead of the combustion front. This effect becomes more pronounced at lower pressures, higher porosities or reduced gas saturations. The peak temperature and the temperature profile on the leading edge of the heat wave stabilize after a certain period. The length of the steam bank remains practically constant, although the length of the water bank increases as the heat wave advances. INTRODUCTION The existence of the vaporization-condensation phenomenon in the heat-wave process and the important role played by the phenomenon have been recognized by several investigators. Kuhn and Kochl stated that steam plateaus were frequently observed on the temperature records of their experiments. The steam plateaus were attributed primarily to the vaporization and subsequent condensation of the interstitial water existing in the oil sand. Szasz2 suggested that both lighter hydrocarbons and water are vaporized on the leading edge of the heat wave, carried forward in the gas stream, and then condensed to create banks of oil and water. Martin et al suggested that the vaporization-condensation phenomenon is one of the main mechanisms of the heat-wave process, along with thermal expansion and viscosity reduction. Wilson et al. reported the existence of a steam plateau several inches in length in their small-scale tube-run experiments. However, this important phenomenon has never been taken into consideration in the numerous theoretical analyses by various authors. 5 The purpose of this work was to study the thermal aspects of a linear heat wave, taking into consideration the vaporization-condensation on the leading edge of the wave, to determine the effect of this phenomenon on the temperature profile of the reservoir, and to investigate how this effect varies when other process variables are changed. THEORY We consider a reservoir of porous medium of cross-sectional area A, extending from x = 0 to x = L. This reservoir contains, aside from the solid matrix itself, a gas phase and a "combined liquid phase" which is a combination of two immiscible liquid phases — namely, an oil phase and a water phase. The oil present in the reservoir is assumed to consist of three fractions, a noncondensable gas, a nondistillable residuum, and a vaporizable oil fraction which may be present in both the gas phase and liquid phase. Before the heat-wave process begins, preheating has taken place and has imparted an initial temperature distribution T,(x) to the reservoir. At the start of the process, a stream of oxygen-bearing gas is introduced through the face at x = 0. This gas supports the combustion of the residual fuel and supplies the heat throughout the process. In order to develop a tractable system of equations, the model properties are postulated as follows: (1) the system is isotropic and homogeneous; (2) there is a uniform fuel content throughout the reservoir; (3) combustion takes place in a moving vertical planar region of infinitesimal thickness; (4) the temperatures of the fluids and the solid matrix are identical; (5) radiation is negligible; (6) the gas and liquid saturations are uniform throughout the reservoir and remain unchanged

Jan 1, 1965

By H. Bartholomew, L. Bernstein

Experirmental bonds of Ag-In SLID to gold, copper, nickel, Kovar, Dumet, nickel-plated molybdenum, ALL-Pt vrzetallizing on ceramic, and nickel-plated Mo-Ti metallizing on Al2O3 ceramic have been made and exalnined. Metallographic taper sections were made of all bonds for Phase identification. In addition, failuve temperatltres were determined for bonds heated undev shear load. Sowe bonds were subjected to electvon-probe microanalysis. The ternary SLID system Ag-In-Sn was similarly evaluated. Plwtonticrogaphs and electron-probe data are discussed and related to over-all phase diagrams , diffusion effects, and wetting properties of the liquid. The rates of diffusion andor compound formation of gold, silver, and copper in indium and In-Sn liquids are found to descend in that order, as measured by the relatzve thickness of phase layers in the interfaces of bonds made at 200to 400°C. It is concluded that the SLID process enables one to produce bonds which are stable at high temperatures, after having been fabricated at low temperatures, and meet most requirements for application in interconnection, silicon bonding, or hermetic sealing of electronic devices. In a previous publication by one of the authors, the theory and principle of SLID bonding in simple binary systems was discussed. SLID bonding can be defined as a joining process using a preform with a laminated structure: a low-melting material clad on a high-melting core. During the bonding cycle a metallurgical transformation occurs such that the resultant structure can withstand, without reliquefying, temperatures higher than those at which the bond was made. The phases present in the joint interface region are high-melting compounds or, if equilibrium is reached, solid solution. Properties will depend on the phases present, ultimately approaching those of the solid substrate core of the SLID preform. The high-temperature strength of bonds made in these systems was correlated to phase identification in the interfacial bond regions from metallographic cross sections and electron-probe X-ray microanalysis data. When complex electronic components are assembled, multiphase systems result at the interfaces of bond regions. In these ternary and higher-order systems very little diffusion and phase-diagram data is available with which to predict the nature of the interfacia1 region that will result from conventional fabrication processes and subsequent field use of the component. Clarke and Rhines did early work in the field using the Al-Mg-Zn system as a vehicle. Guy and co-workers studied a portion of the Cu-Zn-Ni system and some mathematical4 and general5 aspects of multiphase diffusion. irkald' and coworkerse recently studied diffusion in the Cu-Zn-Sn system. No diffusion studies have been made on ternary systems directly applicable to this investigation but some phase diagrams are available: g-u-n, u-i-n, and CU-i-n. I) DESCRIPTION AND EXPERIMENTAL PROCEDURE The elements Au, Ag, Cu, Ni, In, and Sn are found in alloy systems commonly used in fabricating and assembling electronic components. Reference to the appropriate phase diagrams9 and the previous publication will indicate that the binary systems of any of the two low-melting elements, indium and tin, with any one of the other four higher-melting elements are capable of producing SLID bonds. It is not unreasonable to assume that any ternary or higher-order alloy system containing at least one of the elements gold, silver, copper, or nickel and one or both of the elements indium and tin could be used to produce bonds which are stable at high temperatures, after having been fabricated at low temperatures. Indeed, the liquidus contours and isothermal sections of those phase diagrams available7 do so indicate. The parameters affecting the bond and the equipment used in evaluating the bond were described in an earlier paper.' The current investigation used the

Jan 1, 1967

By Fernando A. Buttazzoni, Jorge C. Munita

INTRODUCTION To provide a background for discussing long-range financial and operational planning in the mining industry, we would like to begin by describing the role of planning in Codelco. Having taken part in Codelco's planning process since its inception in 1976, we believe that useful conclusions may be drawn for the experience we shall relate. Although Codelco is a state-owned copper producer with an important role in the Chilean economy, and is consequently very much at the core of national economic planning, the following discussion is not related to government planning but to planning in an operationally and commercially autonomous business concern with all the characteristics of a private enterprise. The only way in which Codelco differs from private business is that its financial successes or failures have a more direct impact on the countryls ability to participate in international trade, to meet its international financial commitments and to achieve economic and social growth. Thus, what follows is a presentation of the conceptual features of the planning process at Codelco and a description of the current state of planning in the company. It is understood that certain conceptual components are basic to any formal strategic planning process, and that the components of Codelco's planning process are therefore generally applicable in similar companies. First, the mission and scope of operation of the company must be defined, and goals must be set to achieve leadership in the business activities in which it engages. Having set this framework, the company must constantly scrutinize those internal elements and conditions that are essential to fulfill its mission and achieve leadership. In Codelco this means considering the actions which can best serve to define future capacities, taking into account declining ore grades and determining optimal production levels; watching over the productivity and skills of its labor force, and; keeping abreast of technological developments in non-ferrous mining and processing. If the company is proficient in these three areas, it will be cost efficient and there- fore competitive. Codelco must also watch over the business environment in which it operates. The company sells concentrate, blister and fire-refined copper, wirebar, cathodes and wire rod and must study the behavior of the market to attune its product mix to the demand existing for these various commodities in the international market and the copper consuming industries in general. By examining the internal and external environment in which the company conducts its production and commercial operations, it is able to diagnose its strengths and weaknesses, to identify the hazards it must overcome to stay ahead in the copper trade, and to take full advantage of business opportunities as they arise. CHARACTERISTICS OF CODELCO-CHILE Although our subject is Codelco, readers should keep in mind that there are many other copper producing operations in Chile, all in the private sector, and many valuable deposits that may be exploited in the future. Codelco is the only public sector copper producer, although there is one other state enterprise that operates smelting and refining facilities principally to serve a large number of very small producers of copper concentrate. In the mid-19801s, Codelco is the largest copper mining company of the world and the largest producer and exporter of copper with yearly sales totalling close to US$ 1.8 billion in 1983. Moreover, it is a highly profitable copper company at a time when the world copper industry as a whole has reported losses for several years. Codelco-Chile is a fairly new organization. The history of the four mining operations it manages is much longer: El Teniente was opened in 1912, Chuquicamata in 1915, Salavador in 1959 -- with installations of the old Potrerillos mine dating from 1927 -- and Andina in 1970. Having had separate owners, the management systems of the

Jan 1, 1985

By Thomas C. Wilder

ALTHOUGH there is an abundance of thermodynamic information available in the literature today, no experimental data on the standard molar properties of formation of zinc oxide have ever been reported for the temperature range 419.5" to 908°C. This is the temperature range for which zinc metal is a liquid. so that the formation reaction is: Data have been reported for Reaction [I] where zinc is a solid or a gas. Maier. Parks, and nderson' measured the electromotive force of the cell: in order to obtain the free energy of the reaction: over a limited temperature range. With the known properties of H2O, those of ZnO were calculated. These workers found that t;j of ZnO is -75,930 ± 150 cal per gfw and Mtf is-83,000 300 cal per gfw at 25°C. akolkin made similar measurements to obtain ilF7 and AH; of -75,870 and -82,540 cal per dw respectively at the same temperature. Truesdale and arirlg and Kitchener and 1gnatowicz4 measured the equilibrium of the reactions: respectively, in order to determine Ff of ZnO from the known values of CO, CO2, and H/X The thermodynamic properties of ZnO, presumably taken from the above investigations, are tabulated by Kubaschewski and vans' and Wicks and Block" The latter reference also gives values for the range where zinc is a liquid. These numbers are probably acquired from the known extremities of the range plus Cp data of the components. In the present work the electromotive force of the cell: was measured in order to calculate the properties of ZnO from the well known values of NiO for the temperature range where zinc is a liquid. In Cell [B] the cathode reaction is: and at the anode: The overall reaction is: for which the free energy change is: where is the electromotive force in volts of cell [B] after correction for the Pt-Ta thermocouple. The standard molar free energy of formation of NiO is very well known as a function of temperature. Kiukkola and agner's data are used in most tabulations. The error is probably less than I00 cal per gfw, The latter authors were the first to use solid mixed oxide electrolytes in galvanic cells. Their work with NiO and other oxides was performed with cells similar to Cell [B] using a variety of reference electrodes of fixed oxygen potential. There may be a small composition range for which either NiO, ZnO or both exist. If nonstoichiometry does exist for these oxides, then the properties described herein are those for the metal saturated compositions. The simple cell design was the same as described elsewheres except that the molten metal electrode was about 125 g of pure zinc including a small (0.25 to 0.50 g) amount of ZnO. The mixture of pure nickel and NiO powders making up the reference electrode was contained in a tube of the ZrOl + CaO electrolyte which was immersed in the molten zinc. A platinum contact was made to the reference electrode; tantalum to the zinc. A refractory cement plug was necessary at the open end of the electrolyte tube in order to prevent zinc vapor from contaminating the reference electrode. Experimental details such as the vessel containing the cell, furnace, temperature control and measurement, and electromotive force determinations of the cell have all been outlined previously. The temperature was varied randomly in the range between the freezing and boiling points of zinc. After each temperature change, time was allowed for the drift at the new temperature to be less than +;"c whereupon a series of three cell readings was taken at least 10

Jan 1, 1970

By F. R. Scauzillo

Equilibrium data which should be useful in the design and/or evaluation of glycol dehydration units were prepared from an analysis of various published data and the correlation of these data by the use of the thermo-dynamic equilibrium ratio. The equilibrium ratios of water are used to solve the glycol absorber problem; such solutions are necessary to define the number of trays and the glycol circulation rate needed to meet drying requirements. Activity coefficients were obtained which relate directly to the equilibrium ratios of water in the water-TEG-natural gas system. These activity coefficients have been used to calculate the equilibrium dew points for aqueous TEG concentrations of 60 to 99.9 weight per cent for the temperature range of 40° to 120° F. They also provide a means of calculating equilibrium ratios for water in the water-TEG-natural gas system; this applies to any desired TEG concentration and to the temperature range from 40° to 120°F. INTRODUCTION During the last several years, the drying of natural gas with aqueous triethylene-glycol (TEG) solutions has become very prominent. Most users of TEG as a drying agent have been satisfied with the performance of TEG solutions at the conditions used; however, there always has been some discussion of the drying ability of TEG solutions at conditions not commonly encountered such as temperatures below 50° or 60°F, but more particularly temperatures above 100°F, and pressures above 1,000 psia. Today, when higher wellhead temperatures such as 120°F are more commonly encountered many are skeptical of TEG's ability to dry sufficiently well to provide dew points around 32°F, which is generally the maximum tolerable when attempting to dry a gas to contract specifications of 7 Ib/MMscf. These views probably have evolved to some extent from the days when suppliers would not guarantee dew-point depressions in excess of 65° to 75 °OF. Also, the feelings about TEG drying may have arisen from the lack of information about the equilibrium relation of water in the drying operations. Porter and Reid' have reported equilibrium data for a 95 per cent TEG solution, while Townsend2 reported equilibrium data for 95, 98 and 100 per cent TEG solutions. Townsend also presented a calculational method which obtains activity coefficients in the liquid phase and, subsequently, the equilibrium water content of a saturated gas over glycol from published3 atmospheric dew points. Wise, Puck and Failey' presented activity data for the water-TEG system at atmospheric pressure. In the past, the equilibrium ratios published for water in a 95 per cent by weight aqueous TEG solution have been used indiscriminately by many for all concentrations of TEG encountered in gas drying operations. Since essentially all such gas operations require the use of more concentrated TEG solutions, a study was undertaken to correlate the existing equilibrium data for aqueous TEG and gas systems and to provide some means of calculating the equilibrium ratio of water in the natural gas-water-TEG system where TEG concentrations were other than 95 per cent. The data presented herein consider only the equilibrium drying ability of the TEG solutions and do not consider the effect of temperature and pressure on the tray eficiency of contactors. In other words, this paper is concerned primarily with the development of the equilibrium relationship between water in the dried natural gas and the water in the lean TEG entering the top tray of the absorber. BASIC EQUILIBRIUM RELATIONS A relationship which relates the K value of water in the natural gas-water-TEG system to the vapor pressure of water at the system temperature, the total pressure of the system and the activities of the liquid and gas phases has been evaluated. It is well known that, for any component of a mixture at equilibrium between a gas phase and a liquid phase,

By Pol Duwez

The effect of the rate of cooling on titanium, zirconium, and thallium has been measured. For titanium-molybdenum alloys, it has been shown that for molybdenum concentration up to 8 pct the rate of cooling has no effect on the transformation temperature, but this temperature decreases progressively with increasing molybdenum content. HIGH strength to weight ratio and remarkable corrosion resistance have often been advanced as the main reasons for the present widespread interest in titanium. For the physical metallurgist, the existence of an allotropic transformation in titanium is another important factor. As in the case of iron, an allotropic transformation may be the fundamental property upon which the response of Ti-base alloys to heat treatment will depend. It is therefore important to study the mechanism of the allotropic transformation in pure titanium and the effect of alloying elements on this transformation. The existence of an allotropic transformation in titanium was reported in 1931 by Schulze.' Later, De Boer et al.' determined the transformation temperature from a discontinuity in the electrical resistivity at 882"42O°C. According to recent work," the transformation temperature is 882.5"&1°C. The crystal structure of the room temperature a phase is hexagonal close-packed and the high temperature fi phase is body-centered cubic.' It is well known that the high temperature /3 phase of pure titanium cannot be retained by quenching to room temperature. Several investigators'-' have shown that in alloys of titanium with metals which are soluble in the @ phase (for example, nickel, molybdenum, chromium, or manganese), the /3 structure can be retained, providing the concentration of the alloying element is greater than a certain critical value. Below this critical value, the alloys transform during quenching, at least partially, into a supersaturated solid solution having the a. structure. This behavior is very similar to that found in some iron binary alloys (Fe-Ni and Fe-Mh, for example) and is an indication that the transformation might occur by means of a shear mechanism analogous to that observed in the austenite-martensite reaction. The present investigation is mostly concerned with the effect of the rate of cooling on the /3 to a transformation. In the first portion of this paper, the results obtained on pure titanium are described. Two other pure metals, zirconium and thallium, were also investigated, because they both have an allotropic transformation like titanium, from an hexagonal close-packed to a body-centered cubic structure. For purposes of comparison, the effect of rate of cooling of the y to a transformation of iron was included in the experimental program. The second part of this paper deals with Ti-Mo alloys. The equilibrium phase boundaries involving the solid state reactions on the Ti-rich side of the system were determined and a study was made of the effect of the rate of cooling on the transformation of the high temperature /3 solid solution. Experimental Procedure Since the main object of the present investigation was the determination of the effect of the rate of cooling on a transformation temperature, the best technique available was that used by Greninger" in his study of the martensite arrest in carbon steels. This method consists of heating a very small sample of metal to which fine thermocouple wires are .attached, cooling the sample rapidly by means of a blast of helium, and recording the temperature vs. time curve on an oscillograph. The apparatus used in the present experiments was very similar to that described by Greninger, except that the heating coil was made of molybdenum wire (0.040 in. in diam) and the assembly was placed in a bell jar under vacuum of 10" mm Hg or less. The specimen con-

Jan 1, 1952

By F. W. Jessen, H. Kazemi

A washing technique has been developed to form a spherical cavity in massive salt. The technique is, basically, a process of controlling the fluid motion in the cavity, the concentration distribution of brine, the rate of dissolution at the walls of the cavity, and the particular settings of the wash pipe, or pipes (inlet and outlet pipe) employed. For a particular arrangement of tubing and casing, fresh water enters from the casing annulus at a position above the bottom of the tubing, and the dissolved material leaves the cavity through the tubing near the bottom of the projected hole. The initial configuration of the cavity is cylindrical, representing the drilled hole situated at the axis of the projected cavity. As washing progresses the original hole is enlarged radially (any direction perpendicular to the axis of the hole). An inert fluid (generally a hydrocarbon, natural gas, or air) which serves as a blanket is injected through the annular space between the original hole and the casing. The controlled downward motion of this blanket maintains the upper edge of the brine region that is expanding on the surface of the projected sphere. A large spherical glass container and a radial model were used to investigate the flow patterns and the concentration distribution of brine occurring during the progress of solution of the salt. Aluminum flakes and dye were injected and flow patterns were observed and recorded on motion picture film. Based on the results of these model studies and other work carried out in this laboratory, the controlled washing technique was formulated. INTRODUCTION Underground cavities leached in salt beds and salt domes have been used extensively for storing hydrocarbons. Little attention has been focused on the shape of the cavities as long as large volumes were obtained and the cavities were structurally stable. The general process involves circulating fresh water and removing brine. Two distinctly different circulating systems can be employed, each of which yields characteristically different shapes. By far the most generally accepted method of washing storage caverns in salt domes is the direct circulation system. Water is introduced through the innermost pipe of a concentric pipe system, and brine is withdrawn through the annulus. In the reverse-circulation method, water enters through the annulus and is discharged through the smallesc tubing string. The size of the operation, and hence the size of tubing and casing used, depends on such factors as cavity volume, length of hole, availability of water, disposal of brine and power requirements. Underground caverns are from 100 to 1,000 ft or more in length, and when completed vary from 40 to 100 ft in diameter, providing storage of 100,000 bbl or more. The volumes of water required per volume of salt removed vary from 6 to 7 for the reverse circulation method to 10 to 11 for the direct circulation method. Up to 80,000 BWPD are often circulated. In the direct circulation method, because water enters near the bottom of the projected cavity, solution of salt is greatest at this point, particularly in view of the fact that when the washing is begun turbulent flow undoubtedly exists in the immediate vicinity of the discharge of the inlet water. As the diameter of the hole increases, flow rates also are increased, so perhaps the condition of fluid turbulence is maintained for some time. During the later stages of leaching, when capacity of equipment may be the limiting factor in maintaining flow rates, there may still exist some turbulence adjacent to the point of influx; however, for the most part laminar flow conditions prevail. There appears, therefore, rather good evidence to indicate that the state of fluid motion is responsible for the typically shaped cavity which results from such washing — namely a cylindrical form, generally somewhat larger at the bottom than at the top. Depending on the number of so-called stages which might be employed, the walls or surfaces of the salt diminish rather uniformly from bottom to

Jan 1, 1965

By T. J. Whalen, M. Humenik

The liquid surface tension of copper-nickel ad copper-nickel-titanium-carbon alloys and the wettability of titanium caybyde by these alloys have been measuhed. It was found that the surface tensions of the binary copper-nickel alloys Lie on a smooth curve between the end members, copper and nickel. The addition of small amounts of titanium and carbon has nO effect on the surface tensions of copper-nickel alloys. Small additions of nickel to copper significantly reduce the contact angle of Ike alloy with titanium carbide. From a Gibbs treatment, nickel is shown to be adsorbed at the titanium carbide-alloy interface. X HE microstructure of two-phase materials has been shown to be influenced largely by the interfacial energies between the phases present.' , In systems prepared by powder metallurgy techniques and densi-fied in the presence of liquid phase, a precise analysis of microstructure and interfacial energy relationships requires a knowledge of the solid-solid interface energies and liquid-solid interface energies. However, marly metal-nonmetal systems are characterized by the "sweating" of the liquid during sintering, and in these systems wettability is a principal consideration. The wetting in turn is dictated by the various interface energies of the system, as shown in Fig. 1 for a liquid drop formed on a solid substrate. The equation which expresses the vectorial balance of surface forces in the horizontal plane, at the point of contact, A, is given by: where ssv = solid-vapor interface energy sSL = solid-liquid interface energy sLV= liquid-vapor interface energy 6 = contact angle measured through the liquid phase. The angle and the surface tension, slv, can be measured accurately by the sessile drop method.3, The absolute value of the surface energy of the solid cannot be determined by this method, but with reasonable changes in the composition of the liquid only, the value of ssv can be considered constant. The changes in contact angle, then, can be attributed to changes in sSL and sLV and since sLV can be measured, the changes in sSL can be determined. Several studies have indicated that the surface and bulk properties of solid alloys can be correlated with electronic structure. The catalytic activity of copper-nickel alloys was reported to follow the dband vacancies in these alloys.5 Nickel has been considered to have 0.6 holes per atom in the d-band. The addition of copper to nickel is thought to bring about a filling of the d-band of nickel, since each copper atom contributes one electron. Thus, at an atomic concentration of 60 Cu-40 Ni (62 wt pct Cu-38 wt pct Ni) the d-band is believed to be full, and magnetic measurements support this view.6 If the electronic structure is influencing a property of the alloy, this property should show some sort of discontinuity as the composition changes from one side of the 60 Cu-40 Ni composition to the other. Since the catalytic activity can be considered as a surface property of the alloy, it is logical to assume that other surface properties, such as surface tension, may also be influenced by electronic structure. The suggestion has been made that there is a correlation between the solid titanium carbide-liquid Cu-Ni alloy interfacial energy and d-band filling.7 One purpose of this investigation was to determine if the changes taking place in the electronic structure with compositional changes in the solid copper-nickel alloys were reflected in the surface tension values of the liquid alloys. Such a change, if present, would lend support to the suggestion that one can refer to discrete energy bands in the liquid state. Other purposes of the present study were to investigate in detail the wettability in the system copper-nickel-titanium carbide, and to discuss the possible processes which take place during wetting in this system.

Jan 1, 1961

By W. S. Gatley, F. C. Appl

This paper presents a combined analytical and experimental study of chisel penetration vs time during chisel impact on rock, a problem of fundamental importance in improving the performance of roller-cone bits or percussion drilling toots. For a given force-time relationship between chisel and rock, the problem of determining the penetration (displacement) vs time of the chisel is formidable. This is so because the rock is a nonlinear system with distributed mass and distributed damping (friction, dissipation of energy due to rupture, etc.). Since the literature does not contain adaptable solutions, the rock behavior to impact was simulated approximately by an "equivalent" lumped system, that is, an "equivalent" mass, spring, dashpot system. With this assumption, an analytical solution was found for chisel penetration vs time due to a sinusoidal load between chisel and rock. From this solution were found curves, in terms of dimension-less variables, for the maximum depth of penetration vs the frequency of the sinusoidal loading and for the energy transfer vs frequency. The results of this analysis were used to predict the penetration rate of rotary rock bits us rotary speed. The curve indicated that an optimum speed exists. To verify this analysis, an experimental apparatus was constructed and used to apply a sinusoidal pulse to a chisel penetrating a rock specimen under atmospheric conditions. Strain gauges were mounted on the chisel shank and a velocity transducer was mounted between the chisel and the rock surface. The velocity was integrated electrically and picked up simultaneously with the strain gauge signal on an oscilloscope. Permanent records were made photographically to provide simultaneous records of force us time and penetration us time. In comparing the experimental results for limestone and dolomite with the theoretical results, good agreement was found in the frequency range of the experiments. Unfortunately, the inertia effect (peak penetration) indicated by the theory occurs at a frequency much higher than could be obtained experimentally with the apparatus constructed. A "rate-of-loading" effect is indicated theoretically, but has not yet been verified experimentally. INTRODUCTION The process of drilling with percussion tools or rotary rock bits is basically related to the transient response of rock to surface impact. Each time a bit tooth contacts the rock, high stresses are developed which result in penetration and rock removal. As the tooth moves on, stresses are relieved and a new cycle begins as the next tooth contacts the rock. Thus the drilling process, which consists of an endless succession of these cycles, can be studied in terms of a single cycle. It is apparent, therefore, that the study of single-chisel impact on rock is fundamentally important in improving the performance of roller-cone and percussive-type drills. Previous studies in this area have been conducted by Simon1 and Hartman2 by means of drop tests. In these tests a chisel was attached to a weight and allowed to fall, due to the force of gravity, so that the chisel was driven into a rock specimen upon impact. Strain gauges were attached to the chisel shank and the resulting force-vs-time curves were recorded photographically from an oscilloscope screen. The depth of penetration and crater dimensions were also measured. These tests have provided much valuable information but, as mentioned by the investigators, have not provided complete information on the effect of "rate of loading'! This is partly due to the fact that the chisel motion during drop tests is not a controlled motion which can be varied in form and frequency. Therefore, it seemed that additional information could be obtained by studying chisel impact under conditions where both the motion and the frequency of loading could be controlled. This paper presents a combined analytical and exper-

By J. L. Lytton, T. E. Tietz

The recovery of flour stress of recrylstallized are-cast molyhdenum after 10 pet prestrain at 150°C was studied for recovery temperatures of 725o 801o and 901oC. The yield phenomenon observed after recovery was such that the yield drop diminished and disappeared as recovery proceeded. A fractional flow-stress recovery parameter fr, was developed and it was shown that, independent of recovery ternperatzwe, equal f, values of about 0.16 produced superposition of stress-strain curves except for the initial yield phenomenon. The activation energy for low degrees oj recovery was found to he 32,600 cal per mole, in close agreement with a reported valzie for difjzdsion of carbon in molybdenum. For values of fr greater than about 0.15 where recovery was thought to predominate over strain aging, the activation energy varied from 43,600 to 82,500 cal per mole and increased with increasing recovery and recovery temperature. A 10 pet pre-strain shifted the ductile-brittle transition temperature, as indicated by tensile elongation, from 10°C. to about -22"C. A 100-hr recovery anneal at 801oC was shown to shift the transition temperature to about —5oC, the major shift occurring during the first hour of recovery. ThE recovery of cold-worked metals is accompanied by changes in the arrangement of the dislocations generated during cold work. In recent years, the use of transmission electron microscopy has allowed direct observation of some of the dislocation configurations formed, such as "tangles", networks, cells, subboundaries, and loops. These observations have recently been reviewed by Keh and Weissmann.' Accordingly, some understanding has been gained concerning the nature of the dislocation rearrangements involved. The relationship between recovery and the decrease of mechanical strength, however, has only recently been explored. Previous efforts of the authors were directed toward investigating the decrease of tensile flow stress of aluminum and Al-1 pet Mg during recovery2 and the effects of concurrent elastic and plastic strain on the flow-stress recovery of aluminum.3 In addition, an investigation of the effect of four different solute additions on the tensile flow-stress recovery of aluminum has been made.4 Many important metals, however, have the bee crystal structure, e.g., iron, molybdenum, tungsten, vanadium, columbium, tantalum, and chromium. These metals might be expected to behave differently during recovery from those with other crystal structures for two reasons. First, the previous and present investigations of aluminum and its alloys have shown that tensile flow-stress recovery is strongly affected by foreign atoms in the lattice. In the bee metals, interstitial impurities are usually present and might be expected to have various effects upon both flow behavior and recovery. For example, heterogeneous yielding might occur during prestraining. The diffusion of these interstitials can also relock dislocations during recovery so that a yield point might be obtained upon restraining (strain aging). Second, some of the bee metals (e.g., iron, molybdenum, and tungsten) undergo the familiar structure-sensitive ductility transition and exhibit brittle fracture at suitably low temperatures. It is of considerable interest to determine the effects of recovery on the transition temperature of such metals. The purpose of the present investigation was to extend our knowledge of flow-stress recovery to the bee metals and to study the effects of recovery on the ductile-brittle transition temperature. Unalloyed recrystallized are-cast molybdenum was chosen as a test material, since it exhibits a well-defined ductility transition near room temperature. As in the previous studies, the degree of recovery was measured in terms of the decrease of tensile flow stress. Prestraining and restraining were carried out at 150°C to avoid the possibility of brittle fracture. EXPERIMENTAL PROCEDURE The are-cast molybdenum sheet used in this investigation was obtained from the Climax Molybdenum Co. of Michigan. It was 0.060 in. thick by 10

Jan 1, 1964

By John F. Elliott, Robert D. Pehlke

The rate of reaction of nitrogen with liquid iron and with binary alloys of iron and Al, Cb, Cr, Ni, O, S, Si, and W were measured. The surface active elements, oxygen and sulfur, decrease the rate markedly. The other alloying elements have very little effect on the rate except when they function as deoxidizers, The rates of absorption and de-sorption were found to be equal. Several possible reaction mechanisms which may control the rate are considered. In order to describe completely the behavior of nitrogen in steelmaking processes, the mechanisms of mass transfer between the gaseous and liquid phases, nitrogen and iron, respectively, must be understood. A kinetic study to determine the nature of these mass transfer processes was undertaken, and the results of that investigation are presented in this paper. Specifically, the study was directed toward determining the influence of alloying elements on the rates at which pure nitrogen gas at constant pressure is absorbed and desorbed by liquid iron solutions: A previous paper1 reported measurements of the equilibrium solubility of nitrogen in liquid binary iron alloys. The experimental data are presented and discussed first and then several possible rate limiting mechanisms are considered. PREVIOUS RESEARCH The results of several investigations on the rate of absorption of nitrogen by liquid iron and iron alloys have been reported.2-14 There is little agreement on the rate coefficients among these studies because of the influence of geometry on the experimental system and of the purity of the liquid iron. The rate was found to be influenced by alloying content for the binary liquid iron systems: Fe-Al,2 Fe-C,4,6 Fe-Cr,4,5,8 Fe-Mn,5 Fe-Ni,5,8 Fe-O,9,10 Fe-O,9,10 and Fe-Si.2,6,7,11 Several investigators12"15 have reported that the rate of nitrogen absorption is increased in a reducing gas mixture and decreased in an oxidizing atmosphere. A mechanism for the retardation by oxygen of the absorption of nitrogen has been described by Naeser18 as the formation of an iron oxide film at the gas-metal interface. The film slows the absorption rate until it disolves in the metal, thus permitting nitrogen to enter the liquid iron. Karwat17 discussed the influence of oxygen in terms of the formation of gaseous molecules of nitrous oxide which represent a higher energy form than the nitrogen and oxygen or the oxidizing gas and consequently constitute an energy barrier for the process. Fischer and Hoffmann10 showed that the oxygen markedly reduces the rate of absorption of nitrogen, the rate constant being one order of magnitude smaller in liquid iron containing 0.15 to 0.24 pct 0 as compared to that in melts containing 0.001 to 0.02 pct 0. Although Chipman and Murphy2 reported that the rate of absorption of nitrogen in liquid iron was essentially independent of temperature, Eklund3 found that the rate increases strongly with increasing temperature as did Kootz4 and Saito.5,6 Karnaukhov and Morozov7 also reported a large temperature coefficient, but related it to increased stirring at higher power inputs in an inductively heated system. All of the authors above have treated their results assuming that the reaction is diffusion controlled, that the surface reaction is in equilibrium with nitrogen gas, and that a "first order" reaction takes place. Karnaukhov and Morozov7 and Humbert; who studied the rate of absorption in a closed system by observing pressure changes in the system as a function of time, concluded that their results best fit a diffusion-type analysis. This was further verified by von Bogdandy, Dick, and stranski18 and Fischer and Hoffmann10 who found the initial rate of

Jan 1, 1963