Search Documents

By H. W. Winkler, Discussion, V. L. Forsyth

The development of a new gar lift valve has removed many of the obstacles limiting over-all gas lift efficiency. The valve is pressure charged in place in a well, and operating pressure can be changed without pulling. Temperature and gas gradient compensation have been eliminated. Intermitting and constant flow installations, using conventional pressure-charged valves, are compared with designs incorporating the new automatic stabilizer controlled valve. Specific well performance data are presented. The means of obtaining and controlling multiple-point injection of gas are explained and contrasted with single point injection. The effect on small diameter strings and multiple string installations is discussed. The effect of flowing temperature gradient on a design using conventional pressure-charged valves, the limitations imposed by such temperature, and the obvious benefits which result from the use of automatic stabilizer controlled valves are shown. Reduction of gas requirements is stated mathematically and demonstrated with specific examples which are identified as to oil company and well. Increased fluid recovery resulting from greater drawdown is illustrated. The economic advantages are mentioned with emphasis on reduction of capital expenditures, as well as reduction in operating expenses. INTRODUCTION Much of the engineering and research work performed with gas lift has been based upon the supposition that under producing conditions gas would be injected at a single point in a well. Many tests were performed in determining the optimum size of the opening through which gas would be passed and the exact placement of the valve equipment. The objectives in a gas lift installation are to unload the well and to efficiently produce the well after it is unloaded. Until recently, the function of upper valves was simply to unload the well. An operating valve located at a proper place in a well served as a single injection point for lifting liquid to the surface. The basic problem in using such equipment is to arrive at operating depth with sufficient operating pressure to efficiently lift the liquid. Few gas lift installations are designed with all required well data available. However, regardless of the quality and availability of data, and regardless of the accuracy of the design, there is the practical problem of preparing and placing gas lift equipment in the well in exact accordance with the plans and intentions of the engineer. In recognition of these and many other problems, attention was directed toward a means of removing the need for temperature and gas gradient compensation, a way to change the gas lift installation to meet the changing requirements of the well itself, and a manner of compensating for changes in oil-water content, fluid volumes, PI, and bottom-hole pressure resulting from flood or repres-suring activity. A device which could actually set and change the operating pressure of gas lift valves in the well would meet most of these needs. There now exists a new gas lift valve which fulfills the original objectives and in so doing actually accomplishes much more. With this device, called an Automatic Stabilizer Controlled valve, there is an exact matching of valve operating pressure and well conditions. Gas is injected at more than one point in the well, thereby making controlled multiple-point injection of gas a reality. Installation calculations are materially simplified and the need for basic temperature and gas gradient data no longer exists. Section I—The Automatic Stabilizer Controlled Valve The operation of the ASC valve is more easily understood by first studying a conventional pressure-charged valve and then inserting the stabilizer element to observe the changes which result. Fig. 1 is a schematic of a conventional precharged pressure-operated valve. The pressure in the dome pd, acts downward, against the area of the bellows A,, to hold the valve closed. The resulting force Bf plus the spring effect of the bellows Sf represents the total force acting to close the valve. Correspondingly, the tubing pressure ptbg works upward against the port area Atbg and the casing pressure pc works upward against a portion of the area of the bellows

Jan 1, 1965

By C. S. Simons, G. Major-Marothy, M. A. K. Grice, D. A. Dahlstrom

The vacuum filter operating variables that influence cake moisture are discussed. The influence of temperature control, particularly through application of steam to the cake, is emphasized. Results of pilot plant studies on filtration of fine hematite concentrates are presented and discussed, and are shown to support the theoretically-derived conclusions. Results on fine magnetite concentrates are also used to support the argument. The relative merits of disc and drum filters from the standpoint of cake moisture are discussed. Moisture content has always been recognized as one of the most important properties of concentrates used as pellet plant feed. Most iron ore concentrates are produced by wet methods, and are finally de-watered on filters. Obviously, a real economic advantage accrues to the ability of control the moisture content of the filter cake within the range required for optimum pellet production. Another consideration, also, has been receiving increasing attention recently. Transoceanic shippers of concentrate cargoes are critically assessing the hazards of excess moisture. The nature and magnitude of these risks have been described, ' and it appears that their elimination may require that residual moisture be somewhat lower than the limit for proper pelletization. Coarse, very free-filtering materials, such as the products of spirals, are usually best handled on top-feed types of machines. The moisture content of the cake may be held at a specified value by proper design and operation, taking into account cake thickness, air-flow rate, and drainage time. Fine-grained concentrates, with which we will be concerned here, must be filtered on Drum or Agidisc machines. With many of these materials, it is possible, by proper design, to meet cake moisture requirements with a conventional filter station. The first installations to produce high-grade pellets from magnetic taconites fell in this class. In fact, the design criteria were developed in connection with operations of Reserve Mining Co. at Silver Bay, inn.,2 and these have been verified repeatedly in other mills. The trend today, however, is toward the production of more difficultly dewatered concentrates. This is due on the one hand to the increasing attention being given to non-magnetic ores, which tend to be far slimier, and therefore much more retentive of moisture, than the magnetites. On the other hand, the pressure to improve the grade of the magnetic ores is leading to finer grinds, which also are more difficult to dewater. In the latter case, the decision to improve grade in an existing operation by finer grinding for better liberation may lead to two unattractive alternatives: 1) substantially higher bentonite consumption, plus the risk of poorer quality pellets, from high cake moisture, or 2) installation of a thermal dryer. There is, however, a third alternative. In recent papers by two of the authors3,4 it was shown that for many materials a significant decrease in cake moisture can be obtained by applying live steam to the cake face during the drying part of the filter cycle. Further, this limited drying appears to have distinct economic advantages compared to thermal drying. It is the purpose of this paper to explore the third alternative. To do this, the results of an extensive pilot study of steam filtration of a hematite flotation concentrate will be critically examined. This study was sufficiently broad so that a number of alternate suggestions (besides steaming the cake) for reducing moisture content were tested, and comparative data for both Drum and Disc filters were obtained. The work was particularly interesting since the concentrate has a high Blaine surface, and is therefore particularly difficult to dewater to the levels required. FILTER CAKE MOISTURE The significant difference between concentrate filter cake as discharged from the filter, a cargo of that same filter cake during or after shipment, and a green ball formed from that filter cake is in the relative volume of voids, or porosity. In every case, the material is a collection of small solid particles held together by the cohesive forces of a liquid. The physical properties of the aggregate are determined by the

Jan 1, 1967

By J. D. Verhoeven

The effectiue distriblltion coefficient has been Measured in a series of vertical, normal freezing experirtzents with large current densities passing through the solid-liquid interface. The results indicate that the effect of the current on solute redistribution is due to electvotransport in the liquid. The high currents produced extensive mixing in the liquid which was considerably reduced by solidifying in small lubing. Analysis of the convection indicates that it probably vesulls from a horizontal temperature gradient produced by the Joule heating- of the electvic crirver~t. Due to the strong dependence of this convection upon the specimen radius, it is conclnded that only for specit~ens with radii of less than somewhere between 1 and 2 mm wilt electric field freezing be getlerally effec-tire at enhancing the purification of zone-melting experittierats in loe-melting alloys. Experiments on 0.8-mm lubes illustrate some interesting potential applications of this techniqne as a means of solute control on smcrll specimens. In a number of papers published within the last few years'-4 it has been found that passage of large dc currents through the solid-liquid interface of a freezing alloy produces a change in the solute redistribution accompanying the solidification. It had been predicted theoretically by Hucke et al.s and by Pfann and Wagner that such an effect would occur as the result of electrotransport within the liquid boundary layer at the solid-liquid interface. These authors independently derived the following relation between the effective distribution coefficient and the variables of the process: Where k0 is the equilibrium distribution coefficient, V is the mobility of the solute relative to the solvent, E is the electric field intensity, D is the solute diffusion coefficient, R is the rate of interface motion, and 6 is the boundary layer thickness. Both groups of authors show that this equation predicts the possibility of extending the purification ability of zone-melting experiments by the addition of an electric current. However, there are other effects in addition to electro-transport which could be produced by the high dc current and might, perhaps, invalidate the applicability of Eq. [I]. For example, high electric current might affect the interface reaction or perhaps the equilibrium distribution which was assumed to exist at the interface. It was the purpose of this work to determine the applicability of Eq. [I] by systematically investigating a simple system for which all of the necessary parameters were known. It was of particular interest for speculating on the potential usefulness of this technique to determine the maximum practical field intensities obtainable, and the effect of these high fields upon convective mixing in the liquid. The initial work in this study was published in a previous paper3 which will be referred to as I. In that work, a current density of 2000 amps per sq cm was used with specimen diameters of 5 mm. The results gave a qualitative confirmation of Eq. [I.], and also showed that a large amount of convective mixing was produced in the liquid by the current. The present study is an extension of that work to smaller specimen diameters and higher current densities. Two points were overlooked in I and will be emphasized here: a) the value of ko has not been well-established in the Sn-Bi system and b) the observed convection could be due to thermal convection produced from the Joule heating. EVALUATION OF k0 To evaluate Eq. [ I.] it is necessary to know the value of the equilibrium distribution coefficient, k,. Tn I the value of k, was taken as 0.3 from a published phase diagram.7 According to ansen' the best data on the phase boundaries of the Sn-Bi system are those of Davidson.5 The data of Davidson give a k, value ranging from 0.21 to 0.25 for the compositions studied in this work, or an average value of around 0.23. In a recent publication, Rigaud and Tougas'10 determined ko by means of a solidification technique. For an alloy of approximately the same composition as that used in this work they obtained a ko value of 0.39. Hence, there is considerable uncertainty in the value of ko and, consequently, a series of experiments were made to determine k, more accurately.

Jan 1, 1968

By Adrian C. Dorenfeld, Theodore Balberyszski, Strathmore R. B. Cooke

This paper reports results of studies of sulfidiza-tion of base-metal oxides and silicates with gaseous sulfur, hydrogen sulfide gas and pyrite and of their subsequent flotation with xanthate collectors. It has been established that a 100% conversion of the oxides of lead, zinc, copper and manganese into their respective sulfides is possible and is a function of reaction time and temperature. Sulfidization of chrysocolla (with malachite and azurite inclusions) resulted in a product containing covellite, chalcocite and digenite in proportions depending on conditions of sulfidization. Reacting cassiterite with gaseous sulfur, H2S or pyrite at various reaction temperatures resulted in its partial conversion to a tin sulfide. Flotation of the products of sulfidization indicated that their behavior is similar to that of natural sulfide minerals, the recovery being a function of the con-version of the oxides to their respective sulfides. The gradual depletion of high-grade sulfide mineral deposits has turned the attention of the mineral industry to the recovery of metals from the oxides and silicates. Anionic (fatty acid) and cationic collectors have in some cases made flotation of nonsulfides possible, although, in general, flotation of oxide ores is not as yet an economic process. Consequently, many attempts have been made to sulfidize the surface of the relevant oxide mineral and thus make it amenable to to In recent years, Bautista and sollenberger4 have investigated the conversion of a number of oxides to sulfides by reacting them with molten sulfur. This paper presents the results of .investigations carried out at the School of Mineral and Metallurgical Engineering at the University of Minnesota to study the flotation characteristics of some sulfidized minerals. It is divided into two parts: The first describes the sulfidization of a number of oxides and a silicate, and the second presents the flotation behavior of the products of sulfidization. SULFIDIZATION OF METAL OXIDES AND SILICATES Experimental Procedure: SULFIDIZATION WITH HYDROGEN SULFIDE GAS — Sulfidization with H2S gas was carried out in a horizontal tube furnace (Fig. 1). The temperature of the furnace was regulated by means of a Variac and determined with a chromel-alumel thermocouple. The constant temperature zone in the furnace was about 6 in. in length, and it was within this zone that the experiments were carried out. The gases employed were supplied from standard compressed gas cylinders, and passed through a glass-wool filtering tower before entering the Pyrex reaction tube. Gaseous products were bubbled through a water tower (used as a flow indicator) and excess H2S was burned off at the end of the outlet tube. Samples of reagents or minerals were placed in a 3-in. Alundum boat and inserted within the constant temperature zone of the furnace. Nitrogen gas (6 ppm O2 content) was passed through the tubes at room temperature to remove air in the tube, and continued to pass while the furnace was heating up. When the required temperature was reached, H2S was allowed to enter the tube and the supply of nitrogen was shut off. At the end of the reaction period, the reverse procedure was carried out, the samples being cooled to room temperature in a nitrogen atmosphere. The flow rate of H2S gas was maintained fairly constant in all experiments, although the rate was not determined. SULFIDIZATION WITH SULFUR POWDER - To study the sulfidization of minerals with sulfur (liquid or gaseous), samples of the mineral, together with a measured quantity of sulfur powder, were placed in a stainless steel (SS316) reaction vessel (Fig. 2). The reaction vessel was heated in a vertical resistance coil furnace, the temperature being regulated through a Variac. At the end of the experiment the vessel was cooled to room temperature before the sample was removed. Cooled products were leached with CS2 to remove any free sulfur. SULFIDIZATION OF TIN CONCENTRATES - Fifty gram samples of sulfidized tin ore were prepared by mixing -48 mesh Bolivian tin concentrate with -48 mesh Ottawa sand in various proportions and sulfi-dizing these samples with H2S in the horizontal tube

Jan 1, 1969

By M. W. Burkart, B. Lustman

Uranium-base alloys exposed to high temperature water fail either by uniform oxidation or by sudden cracking and disintegration of the metal. The disintegration results from the oxidation of a second phase which is precipitated during the corrosion process. The precipitate has been identified as a metastable hydride of uranium. URANIUM-BASE alloys consisting of the body-centered-cubic ? phase are susceptible to two different modes of corrosion failure when exposed to high temperature water. In the first process, a smooth oxide film is formed on the metal surface which continually flakes off during exposure and results in a uniform weight loss of the specimen. The oxide is present as a thin, adherent layer whose thickness remains approximately constant. As the metal oxidizes during corrosion, a nonadherent layer is built up on this film and continually sloughs off. Coincident with the uniform corrosion just mentioned, another process occurs which eventually leads to failure of the metal by cracking and general disintegration. The failure takes place during a relatively short time compared to the total exposure. To distinguish this type of failure from the uniform corrosion, the cracking or disintegration of the metal will be referred to as discontinuous failure. For the ? phase uranium alloys it is discontinuous failure rather than uniform corrosion that limits the useful corrosion life of the alloy. This paper will be concerned primarily with the mechanism of discontinuous failure. Physical Changes During Corrosion—The alloys used in this investigation were ? phase uranium alloys containing 7 to 12 wt pet Mo or Cb. The preparation of the alloys, the method of corrosion testing, and the actual corrosion results are presented in another paper.' The ? quenching treatment consists of annealing the alloy for 24 hr at 900°C in a sealed Vycor glass tube filled with helium and then water quenching to room temperature without breaking the tube. The corrosion behavior typical of a ? phase uranium alloy is shown in Fig. 1. This specimen was a U-12 wt pet Mo alloy tested in pressurized, degassed water at 650°F. The corrosion rate was practically constant at 0.28 mg per sq cm per hr or increased slightly until about 15 to 20 days of exposure, when the onset of discontinuous failure occurred in this particular sample, and the specimen soon began to crack and disintegrate. The simultaneous increase in the observed corrosion rate is a result of the increased area of exposure due to cracking of the specimen. The microstructure of a specimen that failed by cracking is shown in Fig. 2. The presence of a plate-like precipitate can readily be seen. Metallographic examination of corrosion specimens reveals that the onset of discontinuous failure is always preceded by the formation of a plate-like second phase in the ? uranium matrix. Hydrogen analyses of specimens periodically withdrawn from corrosion test reveal that the hydrogen content of the alloy increases on exposure to the high temperature water, as shown in Fig. 3. The hydrogen is available as a corrosion product resulting from the formation of UO2 by the reaction of the alloy with water. Specimens analyzed just prior to discontinuous failure contained as much as 1200 ppm H, whereas the plate-like phase appears to precipitate out at a hydrogen concentration of between 10 and 25 ppm. The observed increase in hydrogen content prior to and during the formation of the plate-like precipitate suggests that this constituent may be a hydride of uranium. Additional evidence linking the identity of this phase to a hydride is that it can be removed by vacuum annealing at temperatures of 100°C and above. Decomposition products of the ? phase would certainly not dissolve at such temperatures, nor could other likely products of corrosion, such as oxides, be dissipated at any of the test temperatures. The precipitation and growth of the second phase during corrosion is accompanied by an increase in hardness of the specimen. The hardness increase results from the dispersion of the harder precipitated

Jan 1, 1959

By H. A. Kendall, W. C. Goins

Several investigations in recent years have shown that drilling rates are increased significantly with increased hydraulic horsepower. But, there has been no over-all method of designing jet-bit programs that efficiently uses the surface power. A study of present practices indicates that frequently as little as 50 per cent of the possible effects at the bit are used. Some observers have indicated that the best utilization of hydraulic horsepower (maximum effect on drilling rate) occurs when the bit hydraulic horsepower is maximum; others have stated that jet impact force is more important, and others have believed that maximum jet velocity is required. Limited efforts to date have shown some optimum conditions for bit hydraulic horsepower and impact, but these conditions cannot exist during drilling of a large part of the hole and do not provide a basis for designing a complete jet-bit program. This paper shows the maximum obtainable bit horsepower, impact force and jet velocity at all depths, taking into account the limitations of the pump, piping, hole and minimum circulating rate for adequate cuttings removal. Ranges of operation are developed; and flow rates, surface pressure and bit pressures are specified for each range to provide a maximum of any one of the desired effects. It also is shown that, by proper selection of nozzle sizes and by following the rules presented, the maximum obtainable quantities can be effectively utilized from surface to total depth. Finally, a simple graphical method of selecting nozzle sizes and flow rates is presented which can be used with familiar bit-company hydraulic tables and calculators to design jet-bit programs for maximum bit hydraulic horsepower, impact or jet velocity, as desired. These programs make most effective use of the pumps. Heretofore, there was no method available for designing field tests which adequately separated the effects of bit horsepower, impact and jet velocity. The programs and procedures developed in the paper are dissimilar and, when used in future field testing, should demonstrate which program is the most important in obtaining the fastest drilling rate. INTRODUCTION During the past decade, rig hydraulics has come into increasing prominence. There has been a definite trend toward providing higher horsepower pumps, jet-type bits have had increased use, numerous investigators"" have reported increased drilling rates as a result of increased hydraulics, and bit manufacturers have provided tablesa-" and calculators that are now commonly used 10 design jet-bit programs. Opinion has varied as to the hydraulic quantity which has the great- est effect on drilling rate. Papers and data have been presented that show pump horsepower,'9 it hydraulic horsepower and jet impact force,' each to be the most significant factor affecting drilling rate. Examinatibn of jet-bit programs of the bit companies indicates emphasis on jet velocity. Only pump horsepower can be eliminated because it can be used to produce any one of the bit effects which, a priori, must be more relevant factors. This contradictory state of opinion and practice regarding the bit effects is unfortunate, but several published references have been concerned with making one or another of the factors maximum; and, because these in each case have given results applicable to only intervals of the hole drilled, there seems to be ample reason to complete the previous efforts. It also is believed that the differences in programs for each effect, where they exist, should be delineated so that future use may determine which hydraulic effect is the more relevant. It is the purpose of this paper to: (1) show the theoretical maximum bit hydraulic horsepower, jet impact force and jet velocity available at all depths, taking into consideration all necessary restrictions on operating conditions; (2) illustrate procedures by which the maximum available horsepower, impact force or veIocity may be obtained; and (3) present a graphical method for rapid selection of jet-nozzle sizes and flow rates to be used with conventional procedures to design jet-bit programs for maximum bit horsepower, impact force or velocity as desired.

By J. C. Yannopoulos, N. J. Themelis

Ah electronic thermogravirnetric balance was used to measure the veductioiz rule o single cirpric oxide particles suspended in a stream of hydrogen. Very jzne thermocouples embedded in lie center and at the surface of the sphere recorded the variation of terw perature during reduction. In contrast to iron oxide reduction, where in most instances the rate of interface reactiokl is controlling, the heat- and mass-transfer phenotnena play a predolrinant role in the reduction of cupric oxide. The correlation of experitnental data or tnass lransfev lhrough the boundary layer at Reynolds nunlber 0-4 50 was as jollocs: ThE reduction of cupric oxide by hydrogen is represented by the equation: It is a highly exothermic reaction and the amount of heat released varies only slightly with temperature (-21,430 cal per g-mole at 400°C). Most of the published studies on this system have been conducted at temperatures in the range of 34 to 280c.l-&apos; The concensus of opinion has been that at temperatures below 200°C the reaction is preceded by an induction period during which there is very little or no reduction. The length of this period diminishes as the temperature of the reaction is increased1l5 and aseawa found that at 280°C reduction starts practically immediately when the oxide is exposed to hydrogen gas. The existence of an induction, or incubation, period has led experimenters to believe that the reduction of CuO by hydrogen is catalyzed by metallic copper.&apos; Boldurev and rmolaev found that mechanical additions of powdered copper to oxide did not affect its reduction, although metallic copper produced during the reduction seemed to have a catalytic effect. At least three other authors2&apos;5&apos;7 have reported that addition of copper had no effect on the rate of reduction. Pease and alor&apos; observed that water vapor had a strong inhibiting effect on the reduction at 1503C, but its effect was greatly diminished at 200 C. Pavlychenko and Rubinchik5 studied this reaction at 159 to 235 C and found that, once the reaction had been initiated, there was no inhibiting effect due to the introduction of water in the hydrogen stream; at temperatures above 183°C there was no inhibiting effect due to water vapor, either before or during reaction. The same authors noted that the rate of reduction was independent of pressure in the range of 200 to 700 mm Hg. aseawa investigated the kinetics of the CuO-Hz system at 160 to 280°C and estimated the apparent activation energy at 14,000 cal per g-mole. A similar value (13,500 1200 cal per g-mole) was reported by ond&apos; in the temperature range 148 to 216°C. Bond also reported that there was no incubation period and that water vapor had no inhibiting effect on reduction at temperatures above 190 C. The above studies have been conducted at temperatures below 280°C and the physical configuration of the system under investigation has not been defined adequately. However, it is well-known that the mechanism of gas-solid reactions depends on a number of in series physical and chemical rate prcesses.&apos;&apos; It is, therefore, essential to include among the experimental factors the geometry of the solid system and the mass-transport characteristics of the reducing gas. Scott studied the reduction of packed beds of cupric oxide cylinders by Hz-He streams of very low hydrogen concentrations at temperatures 400 to 600 C, pressure of 10 to 30 atm, and gas velocity from 0.18 to 5.8 ft per sec (3 < Rep < 30). The reduction rate was found to be mainly controlled by diffusion through the boundary layer and through the pores of the reduced copper phase. The following correlation was proposed: Scott in an earlier work studied the reduction of fixed beds of cupric oxide wire and found that the rate of flow of the gas stream through the bed had a controlling effect on the rate of reduction. The same mass-transfer phenomenon was observed by Bond and clark13 on a similar reduction system. The analogy between mass and heat transfer through the boundary layer which exists between a solid surface and the bulk stream stems from the similarity of the differential equations representing these phenomena

Jan 1, 1967

By K. H. Kilgren

At high formation pressures the distillate produced from a gas-condensate reservoir may be black in color. In this event the dense gas phase existing above the dew point is correspondingly dark. Volumetric phase data and an analysis of a reservoir fluid exhibiting these characteristics, together with a description of the visual equilibrium cell in which these observations were made, are presented in this paper. INTRODUCTION Previously the author, like many others in the oil and gas industry perhaps, tacitly assumed that the expressions black or dark oil system, crude oil system and bubble-point system were synonymous. Crude oil reservoir fluids are bubble-point systems and yield a black or dark stock-tank oil of relatively low API gravity. Conversely, a clear or amber colored trap distillate of high API gravity is assumed indicative of a dew point system or a gas-condensate reservoir fluid. This broad classification appears satisfactory for shallow reservoirs, but as the following study demonstrates, may be misleading when applied to deep reservoirs. Theoretically, there is no reason to exclude the possibility of producing a dark, low-gravity distillate from a gas-condensate reservoir. At sufficiently high values of pressure and temperature, heavy, dark-colored hydrocarbons may exist in the vapor state of a multi-component system. If enough dark-colored components are present in the reservoir vapor phase, the resulting condensate will be dark. The reservoir fluid investigated in the present study supports this contention. Stock-tank production was black in color and measured 29" APT gravity. From outward appearances, the liquid closely resembled a medium gravity crude oil. Experimental measurements proved the reservoir fluid was in reality a gas-condensate system. Volumetric phase data for this high-pressure system and a description of the visual cell in which the study was conducted successfully are presented in this paper. THEORY Phase behavior of a reservoir fluid can be predicted accurately with reference to a pressure-temperature phase diagram. If the reservoir temperature is lower than the critical temperature of the hydrocarbon fluid in place, bubble-point behavior will be observed. If the reservoir temperature lies between the critical and cricondentherm temperature, dew point behavior and retrograde condensation will occur. For reservoir temperatures above the cri- condentherm, only a single gas phase can exist in the reservoir regardless of pressure. Providing the composition of the reservoir fluid were known, it would be possible to predict the critical temperature and estimate the phase behavior from equilibrium relationships. However, the usual practice is to obtain a sample of reservoir fluid, subject it to varying pressures at the reservoir temperature and observe the phase behavior experimentally. The latter method was used to obtain the data reported here. WELL AND TRAPPING INFORMATION A summary of pertinent data for the well from which the reservoir fluid was sampled is presented in Table 1. This well is located offshore Louisiana. Except for the pressure which substantially exceeds hydrostatic pressure, the information does not appear unusual. Prior to the sampling program, the well was produced for 22 hours at a stock tank oil rate of 139 B/D. Average trapping conditions and gauging data for the six-hour test period that followed are summarized in Table 2. Samples of the first-stage trap gas and liquid were obtained during the latter portion of the test period. Ambient temperature remained 5 to 10F below trap temperature and presented no problem for sampling. Surface wind and moderate foaming of stock-tank oil presented some difficulty in obtaining accurate stock-tank gauges. SAMPLE ANALYSIS Compositions of the gas and liquid samples are shown in Table 3. The trap gas was analyzed by isothermal chromatography which revealed only a trace of heptane in the stream. The trap liquid was initially analyzed by low-temperature fractional distillation, yielding a bottom product of heptane and heavier components. Specific gravity of this fraction was measured and the mol weight was determined by freezing point depression. The hexane and lighter overhead gas collected during distillation was

Jan 1, 1967

By Robert E. Green, Robert A. Swanson

Ultrasonic attenuation and stress were measured simultaneously as a function of strain for aluminum single crystals tested in compression. The propagation mode and polarization of the ultrasonic waves were chosen with reference to the theoretical analysis presented in Part I. Good experimental agreement was found with this theory and with earlier experimental work in tensile tests. Support is given to the contention that ultrasonic -attenuation measurements are much more sensitive to the early stages of plastic deformation than are conventional stress -strain measurements. Dislocation meclzanisms are suggested which are compatible with both the present and the earlier experimental observations. A brief historical introduction of previous work concerned with the study of dislocation motion by ultrasonic-attenuation measurements has been given in Part I. The purpose of the present experimental investigation was to make use of the theoretical considerations from Part I in order to gain further knowledge concerning dislocation motions during plastic deformation. Emphasis was placed on the choice of propagation modes and polarization of the waves, such that interactions between these waves and dislocation movement on a specific slip system could be investigated. EXPERIMENTAL PROCEDURE Since the primary concern of this investigation was dislocation damping, other sources of damping were eliminated as much as possible. The test specimens were 0.5-in.-diam single crystals of 99.99+ pct pure aluminum grown from the melt by a modified Bridgman technique. Ultrasonic-attenuation measurements were made at a frequency of 10 megacycles per sec using a Style 56A001 Ultrasonic Attenuation Comparator manufactured by Sperry Products Inc. after a design by Chick, An- derson, and Truell.1 At this frequency the particle vibrations are essentially adiabatic and thermo-elastic damping should be absent. This frequency was selected since it was one of the frequencies used by Hikata et al.2 n conjunction with tensile tests on aluminum crystals, thus allowing direct comparison with this work. The use of quartz-crystal transducers insures that the amplitude of vibration is not sufficient to cause the break away of the dislocation loops from weak pinning points. The quartz-crystal transducers used all possessed a resonance frequency of 10 megacycles per sec and were thin circular discs 0.375 in. in diameter. X-cut crystals were used to generate the longitudinal waves and AC-cut crystals to generate the transverse waves. Aluminum was chosen as the basic material because it is a typical fcc metal whose deformation behavior is well-known and because the most recent work at the time the present research was initiated was that by Hikata et al. who used aluminum. The present tests were run in compression to see if such tests could be satisfactorily run in compression without being severely masked by grip effects.. A second reason was to compare the results in compression with those of the tension experiments of Hikata et at. Finally, shorter specimens could be run in compression with less over-all damping than in tension. All of the aluminum-crystal test specimens used were oriented for plastic deformation by single slip; i.e., they possessed the orientation having a maximum Schmid factor of 0.5. Because of the well-known time dependence 3 of plastic strain at constant stress, the test specimens were subjected to a quasi-static loading. Previous investigations4-&apos; have indicated that attenuation after plastic deformation is also time-dependent, so any continuous loading of the specimen would show that changes in attenuation were also a function of strain rate. By loading the specimen to a given stress level and holding it constant until the recovery process was essentially complete, the time dependence was eliminated. The quartz transducer was permanently bonded to the aluminum crystal using Eastman 910 cement. Excess cement was removed from around the quartz with DMF (dimethyl formamide). Eastman 910 was found to be far superior for bonding, especially with regard to the shear-wave transducer, since it formed a solid bond which readily supports shear-wave propagation. The solid bond formed by the Eastman 910 cement also insured that the quartz

Jan 1, 1964

By F. E. Jaumot, R. L. Smith

Self-diffusion in zinc at temperatures below 200°C has been studied using both single crystal and polycrystal samples. Anomalous results were obtained for single crystal samples, the data indicating that in some cases grain boundary diffusion predominated. These anomalous results are presumed to be due to low angle lineage boundaries in the single crystals. When volume diffusion occurred in either single or polycrystal samples, the values for the diffusion coefficient were as much as several orders of magnitude larger than would be expected from high temperature data. ONSIDERABLE work has been done on self-^-*diffusion at temperatures in the neighborhood of two thirds of the melting temperature (in OK) and higher, but very little has been done at lower temperatures. This is particularly true of self-diffusion in single crystals. This paper reports work on self-diffusion in zinc at temperatures below 200 °C where both polycrystalline and single crystal samples have been used. The measurements were made using both the sectioning and absorption techniques. The experiments on diffusion at low temperatures were initiated primarily for three reasons: to obtain data from single crystal diffusion covering a wide range of temperatures, to obtain values of the activation energy for grain boundary diffusion, and to obtain, if possible, a lower limit to the temperatures at which the absorption technique may be used. It is possible to determine whether volume or grain boundary diffusion predominates at low temperatures by analyzing the manner in which the concentration of the diffusing atoms varies with the depth of penetration. The analysis is possible only for the sectioning technique. For volume diffusion and for the boundary conditions of the present experiment, the curve of the logarithm of the concentration, C, vs the square of the penetration depth, x, is a straight line with the slope proportional to — 1/D. If grain boundary diffusion predominates, Fisher&apos; has shown that a curve of In C vs the first power of the penetration depth should be a straight line. This linear dependence of concentration on depth has been observed experimentally by several investigators. (See, for example, refs. 3 and 4.) Following Fisher&apos;s analysis, the grain boundary diffusion coefficient can be written as where 8 is the grain boundary width, D, is the volume diffusion coefficient at the temperature involved, t is the time of diffusion, C is the concentration of diffusing material, and x is the depth of penetration. A more general analysis employing the same model as Fisher&apos;s but with fewer assumptions has been given by Whipple.&apos; In contrast to Fisher&apos;s analysis the more general analysis of Whipple does not always yield a straight line relation between In C and x. Recently Turnbull and Hoffman have discussed both analyses and have applied the Fisher-Whipple model to a more refined dislocation model of the grain boundary. They have also discussed the possibility of a large effect of grain boundary direction on diffusion. In the case of the absorption technique, for which results are also given, one simply gets a value for the diffusion coefficient with no indication of the predominating mechanism. Experimental Techniques Single crystals of 99.99+ pct Zn were grown using a modified Bridgman method. Polycrystal samples were prepared in three grain sizes (small, about 4 mm2; medium, about 9 mm&apos;; and large, about 25 mmz) by quenching, air cooling, and furnace cooling. The grains of the polycrystalline samples tended to be columnar, with some preferred texture such that the c-axis was inclined at about 20" to 25" from the normal to the diffusion face, particularly in the medium and large grain size samples. The samples were cut from the rod, polished, and heavily etched, and faces cut accurately parallel using a jeweler&apos;s lathe. They were again etched to remove the lathe smear and annealed for 3 hr at 250" to 300°C. After annealing, they were etched, examined, and the orientation determined by Laue back reflection photographs. They were then electroplated with Zn. The plated surfaces were examined for uniformity; nonuniform coatings were removed by etching and the samples replated without additional preparation. For the diffusion anneals, the samples were placed in pairs, with active faces together, in evacuated Pyrex tubes. Constant temperature baths were used, and the variation in temperature did not exceed ±l°C, Diffusion runs were made at l00°,

Jan 1, 1957

By Kenneth A. Moon

An exact statistical treatment of a one-dimensional model is used as a basis for evoluating the reliability of certain simplified expressions for the activity of the solute in interstitial solutions, including one obtained from the exact expression by setting the repulsive interaction equal to infinity. The latter approximation is found to be satisfactory at low and moderate concentration if the repulsive interaction is large, even though not infinite. A similar expression (identical if the co-odination number is two) is derived from the quasichemical expression of Lacher, and is recommended as the best available expression for the excess configurational entropy of interstitial solutions with excluded sites. Some reasonable models are discussed, and the nature of the saturated solutions is determined by inspection. Some of the models reduce to the one -dimensional case. An analysis is given of the excess partial entropy of hydrogen in V-H; Nb-H; and To-H solutions. MOST treatments of the statistical thermodynamics of interstitial solid solutions have followed the classic paper1 of Lacher in making the simplifying assumption that the configurational entropy of the solution is ideal. However, it is becoming increasingly apparent that there are many interstitial solutions with very large so lute-solute repulsions, and for these the assumption of ideal entropy is not valid or useful. It is important to realize that with substitutional solutions large repulsions between the component atoms must lead to phase separation, whereas in interstitial solutions the free energy of the solution is not drastically increased by large solute-solute repulsions until intrinsic saturation is reached at the concentration where further solute would be forced to enter a site in which it would experience the repulsive effect of one or more solute atoms already present. In the limiting case of an infinitely large repulsive interaction, the excess free energy would be attributable entirely to excess entropy, the enthalpy of mixing being zero. AS will be shown below, even if the repulsions are less than infinite, a treatment based on an assumption of infinite repulsions may be very satisfactory up to moderately high concentrations of the interstitial component. Often in solutions where large repulsive interactions exist, there are also small interactions — often attractive—between solute atoms in configurations other than that corresponding to the large repulsion. In such cases the excess free energy will consist of an excess entropy term attributable to the large repulsive interactions, and an enthalpy term corresponding to the other small interactions. Nomenclature to differentiate succinctly between important cases would be a convenience. In this paper the nomenclature shown in Table I will be used. In Table I, and in the preceeding discussion, excess quantities are defined in terms of standard states which are pure solid solvent and pure (possibly hypothetical) solid saturated phase of the structure in question. In practice, it is more convenient to choose the interstitial element as a component, and its conventional standard state. This will add a composition-independent term to the excess entropy and the enthalpy. The earliest paper known to the present author which treats the thermodynamics of athermal interstitial solutions was given by schei12 in 1951, but the statistical derivations in that paper are open to criticism. Speiser and Spretnak were the first to give a correct statistical treatment,3 limited, however, to concentrations sufficiently low that the number of empty sites excluded from occupancy by more than one filled site is negligible. The purpose of the present paper is to extend the statistical treatment to more concentrated solutions, and to examine the magnitude of the errors introduced by assuming that the repulsive interactions are infinite when in fact they must be finite. THE QUASICHEMICAL APPROXIMATION Fortunately, a standard method already exists for taking into account the effect of large interactions upon the entropy of mixing. This is the quasi-chemical method, in which the probability of existence of a given pair of solute atoms in a certain proximate configuration is assumed to be proportional to exp(-w/kT), where w is the energy increase of the solution when the two atoms are moved from isolated locations in the solution to the configuration in question. A quasichemical treatment of interstitial solutions was given in 1937 in a widely neglected paper by Lacher.4 The result comes out

Jan 1, 1963

By G. J. Dickman, W. N. Thomas

The factors involved in selecting, a drive system for a grinding mill, including gearing arrangement, motor selection, and electric-supply system limitations are reviewed. Equipment costs are evaluated on a dollar per horsepower basis and starting performance is analyzed, the latter making use of a recently developed computer program. The present interest in large-diameter grinding mills and the rapidly rising cost of the drive in proportion to the cost of the mill establishes a need to explore the drive system in detail. The drive for a 7 to 8,000 hp mill will cost from $350 to $600,000 which represents nearly half the total cost of the mill package, and requires as much building space as the mill proper. Some of the drive components require a longer time to manufacture and the installation time and costs are equal to those for the mill. It is apparent that the drive has become a dominant factor in the overall mill design consideration. A new plant requires a tremendous investment in both time and money. With the high degree of competition in the mining industry, low capital cost is an exceedingly important factor in the development of a project. It is just as important, however, to insure that the equipment is going to perform satisfactorily for the anticipated life of the project without adding unplanned operating, maintenance, and replacement costs. This is the position in which the engineer or designer usually finds himself and is really one of his primary functionsestablishing a realistic compromise between cost and performance. Large primary grinding mills can represent a major portion of the cost of a plant and the drive system accounts for a substantial part of this cost. These facts justify a careful analysis of the drive requirements and all of the factors involved in ultimately arriving at the best system for the lowest cost. A number of excellent papers have been published on various aspects of mill drives. The authors have used information from these papers in making a study of a drive for a 7600-hp, 32 x 12-ft autogenous mill. This was a broad investigation, including mechanical and electrical design, layout, performance, and maintenance considerations, and overall economics leading to the selection of the optimum system for that mill. This paper was developed from the study and includes information applicable to large mills in general. For a successful and economical application, the drive must be considered as a system and all of the components analyzed to determine their effect on the system. This requires the participation of the mill designer, gear, and other mechanical component manufacturers, motor manufacturer, plant designer, and operator. A careful analysis of the mill torque requirements is first necessary to provide a basis for selection of the mechanical and electrical drive components. Because of manufacturing limitations on the size and capacity of gearing available for these low-speed applications, an evaluation of costs for various gear ratios and configurations in conjunction with motor speeds is required. Consultation with the power-supply company is necessary to determine limitations on motor-starting disturbances and to analyze operating costs on the basis of existing rate structures and low characteristics. Finally, consideration must be given to the drive arrangement and its affect on plant layout, space requirements, and location of auxiliary equipment for the selected process. There are presently three basic schemes for driving a mill. The first is a direct drive by a motor operating at mill speed with no gearing. The second is by a higher-speed motor through a trunnion-connected gear drive. The third is by a motor through the more conventional pinion and ring-gear with the option of an interposing gear box to permit greater motor speed than pinion shaft speed. [(Fig. 1.)] Several manufacturers have or are presently developing motors which drive the mill directly without the use of gears. One arrangement has the motor armature intimately surrounding the mill shell-discharge spout or extension of the trunnion journal. The motor stator is then supported independently and surrounds the shell or trunnion-mounted rotor. Another variation utilizes an independent mill-speed motor connected to the trunnion by a drive shaft and flexible couplings.

Jan 1, 1972

By Y. Shimomura, M. Serizawa, Y. Takahashi, K. Miyagawa

The "semi-pellet" sintering method developed and currently being used at the Fuji Iron & Steel&apos;s Hirohata Works is discusssd. It is shown that the method makes fine-sized material easily sinterable and increases sinter production. The operation can be incorporated readily into conventional sintering plants. Sintering plant raw materials currently being used in the Hirohata Works consist of 40 pct pyrite cinder, 40 pct fines resulting from crushing and screening of imported ores, and 20 pct others, such as mill scale and iron sands. Pyrite cinder, a major component in the sinter feed, has been getting finer since 1952, due to the increased grinding required for the improvement of the results in the iron sulfide flotation and to the adoption of FluoSolid roasters in sul-furic acid plants; some fines pass 100-mesh sieve almost completely. Increased use of the fine-sized pyrite cinders in the sinter raw mix resulted in such difficulties as decreased bed permeability, uneven firing conditions, and low yield. In an attempt to study the cause and to find a remedy for this problem, a series of experiments were made, using an 80-kg experimental sintering pan. As a result it was established that, by rolling the fine-sized pyrite cinders into small balls of 10 to 3 mm diam (hereafter called semi-pellets) and mixing them into the sinter raw mix, the bed permeability was improved, the sintering time shortened, and the yield and production rate increased. It is proposed that this new method be called the semi-pellet sintem&apos;ng. In recent years the pelletizing process has taken the spotlight in the agglomeration field for treating fine-sized ores here in Japan as well as in the U.S. and Europe. This process produces pellets suitable for the blast furnace charge as such, and consists of three major operations: fine grinding, balling, and firing. With regard to the firing technique, some problems still appear unsolved. In the semi-pellet sintering, however, several ad- vantages can be claimed: the balling operation is relatively simple because only small-sized balls are shown to be acceptable and the operation can be readily incorporated into the conventional sintering plant, since only balling, not grinding or firing, equipment is needed. Basic test work on the process was initiated in 1954 and favorable results were obtained. Accordingly a pilot plant was built in 1955 and the test work was continued. The semi-pellets thus prepared in the pilot plant were tested further by USing them in the actual sintering pan and their beneficial effects ascertained. In late 1956 a drum-type balling machine (2.4X4 m) was installed and it went into operation in April 1957 in conjunction with the Greenawalt sintering plant (8 pans having dimensions of 7.2 m in length, 3 m in width, and 0.3 m in depth). In October 1958 a cone-type pelletizer, with a 2.2 m diam, and later a disk-type pelletizer were further added in the plant. In the DL sintering plant (2000 tpd), newly built in July, 1960, four disk-type pelletizers (3.2 m diam, 10 tph capacity) were installed. By mixing the semi-pellets thus prepared with the feed, the sintering operation was found to be greatly improved. The results of the basic test work, and the equipment and operation of the semi-pellet sintering operation at the Hirohata Works will be described. ON THE SINTERING CHARACTERISTICS OF FINE SIZED PYRITE CINDERS To ascertain the effect of addition of fine-sized pyrite cinders on the sintering characteristics, a series of measurements on bed permeability was carried out by varying the size distribution of pyrite cinders. The composition of the raw mix used in the tests was fixed at 50 pct pyrite cinder, 20 pct Larap magnetite fines, 30 pct sinter return, and 5 pct coke; only the size distribution of the pyrite cinder was varied. Also the moisture content was changed at each size distribution. The results are given in Fig. 1. For all pyrite cinders tested the bed

Jan 1, 1961

By F. D. Hoyt, H. L. Hartman

The development of new processes and methods by The Pennsylvania State University to improve slate quarrying technology has centered in recent years on cutting and sawing stone in the quarry to eliminate a second cutting process in the mill. Two machines exhibit promise for this work: 1) a circular saw mounting diamonds or hard inserts to produce smaller sizes of stone and 2) a chain saw with insert cutting teeth to produce stone in the larger dimensions. Prototype machines have been constructed and tested in several Pennsylvania slate quarries, and one commercial installation has been operated for several months with a circular diamond saw. Other kinds of dimension stones may be cut by these saws. Research at Penn State has begun to study the fundamental cutting action of rotary tools or saws in slate and other dimension stones. A laboratory drill press is being instrumented to permit thrust-torque-rotational speed us penetration rate studies of single tooth cutting surfaces on stone. Machinability studies of slate conducted with tungsten-carbide inserts have been performed. The dimension stone industry generally accepts the rather basic premise that the larger the block removed from the quarry, the more practical and economical the operation. Thus, the concept of cutting to size any dimension stone while it remains in place in the parent bed would receive little consideration from the majority of members of the industry. However, the slate industry, which is usually considered a separate member of the dimension stone family, is pioneering in the development of an in-place sawing method. Before any final decision can be reached concerning a proposed new system, it is essential to take a long, hard look at the present method of operation in order to determine if the new system is indeed an improvement or even desirable. In the following section is a brief description of present quarry practice in the slate quarries of eastern Pennsylvania. PRESENT METHOD OF QUARRYING SLATE In the numerous slate quarries of Lehigh and Northampton Counties of Pennsylvania, the grain and cleavage of the slate are most often at right angles to each other; if a third surface is broken at right angles to these two natural planes of weakness, blocks of more or less rectangular shape can be separated.&apos; In conventional quarrying a large calyx core drill prepares holes of 36-in. diam in which wire-saw standards are positioned. By wire sawing between strategically located core-drill holes, large sinks or benches of virgin slate are opened up. The sides freed by wire sawing will vary from quarry to quarry but generally are rectangular in shape with dimensions averaging 20 ft in length and about 15 ft in depth. Some quarries are fortunate in having a joint or natural parting to work to, which of course diminishes the amount of core drilling and wire sawing required. Once the various benches have been developed either through wire sawing alone or through a combination of wire sawing and natural jointing planes, the block removal proceeds in the following manner. A plug hole is drilled in the block with a compressed-air hammer and a feathering chisel is inserted in the hole to cause a fracture of the rock either with or against the grain as indicated by the positioning of the so-called feathers. This operation is referred to as sculping. After a block has been freed with and against the grain by means of wedging from the cross fracture with long bars or levers, the block is further freed along the cleavage plane by shimming it up with small wooden pieces in an operation known as styling. A large steel loading chain is wrapped around a block thus freed and the chain is attached to the wheel of an overhead cable. The block is then hoisted vertically to the cableway and moved along this cableway laterally to the lip or edge of the quarry. From here it is unloaded onto a rail car or truck for transportation to the processing mill. Except for occasional blasting to free stubborn blocks,

Jan 1, 1961

By H. S. Thomsen, W. C. Duesterhoeft, R. E. Hartline

The attenuation and phase shift which formations produce in the electromagnetic field of an induction-type electrical well-logging instrument are great enough to substantially affect the response of the tool to formation conductivity under normal logging conditions. The application of the general equations for the propagation of an electromagnetic field in a conductive medium to the transmitter-receiver coil pair of an induction-logging-tool coil system gives an expression for the response which properly takes the propagation effects into account. A comparison of a calculation of this type with the response computed from the commonly used geometric factor concept, which does not include the propagation effect, leads to a factor Go representing the ratio of the responses computed by the two methods. The value of Go decreases not only with increasing formation conductivity, but also with increasing transmitter-to-detector coil spacing. For a single coil pair with a 40-in. spacing, the value of Go is 0.972 in a 20-millimho/m formation. The value is reduced to 0.915 and 0.812 for conductivities of 200 and 1,000 millimhos/m. As a result, the basic signal generated by the induction-logging coil system is not linearly related to formation conductivity as expected from the geometric factor concept. A uniform conductivity scale can be obtained only by adding a suitable nonlinear element to the recording system. The addition of auxiliary coils, having spacings less than the main-coil span, to achieve focusing results in an even greater departure of the basic signal from linearity with conductivity. The solution of the field equations near the interface between two formations of different conductivity gives the curve shape on an induction logging tool in crossing the interface. The addition of auxiliary coils to achieve focusing can add anomalous character to the curve shape in crossing the interface, which might be mistaken for lithological detail. Preliminary calculations which include the propagation effects in the determination of the conductivity correction for thin beds lead to correction factors which are substantially smaller than those obtained from geometric factor considerations. It is apparent that thin-bed corrections derived from geometric factor calculations are of doubtful validity. INTRODUCTION Although the electromagnetic induction type of electrical well log has been used for a number of years and has gained general acceptance in quantitative well-log interpretation, no technically complete investigation of the mechanism and of its operation has been published. The studies which have been presented are based upon the premise that neither the shape nor the intensity of the induction field of the logging tool is in any way affected by the electrical characteristics of the formation. From the inception of induction logging it has been recognized that under some formation conditions the performance of the instrument could be expected to be substantially different from that predicted by the simplified analysis. This anomalous performance has been called "skin effect" since it is the result of the same phenomenon which causes high-frequency alternating currents to flow only near the surface of metallic conductors. In the range of conductivities encountered in the sediments, the formation actually does not exhibit the sharply defined conducting "skin" shown by metals. The gradual modification of the distribution of the currents in the formation, produced by the induction field of the logging tool, is the direct result of phenomena associated with the propagation of the electromagnetic field through the formation. Therefore, it can be much more appropriately described as the "propagation effect". One purpose of this paper is to review the results of a solution of the equations for the performance of a single transmitter-receiver coil pair induction-logging system which takes into account the propagation effect, showing the manner in which the tool performance established by this analysis differs from that derived from the less comprehensive analyses currently in use. PRINCIPLE OF OPERATION OF THE INDUCTION LOGGING INSTRUMENT The high-frequency alternating current which is maintained at a constant value in the transmitter coil

By F. C. Pittman, D. W. Harriman, J. C. St. John

This paper mentions briefly the history of hydraulic jetting as applied to perforating and fracture initiation. It points out the advantages of hydraulic perforation and undercutting as an aid for creating a fracture at the point desired rather than depending upon the weakest point in the formation for breakdown. It describes early experimental work with jet nozzles in search of better nozzle materials. The effect of splash-back damage and its subsequent influence on jet body and tool design during this work is discussed. A series of cutting-rate curves for jets cutting steel and steel-cement-formation combinations is presented to show the effect of hydrostatic head and the point of diminishing returns with respect to cutting time. There is a series of photographs showing various types of rock formation in which perforation and undercutting tests were made. These stones were drilled and the casing cemented in place as in an actual well. The casing was perforated and circularly cut as if preparing for a fracturing job. The conclusion reached in the paper is that hydraulic jetting with sand-laden fluid can be used for perforating and undercutting casing, cement and formation rock for the intended purpose of inducing the formation to fracture at a desired point. INTRODUCTION Hydraulic jetting as a means of cleaning a formation during acidizing has been used for many years. The acid-jet gun was used to clean formation and for drilling cement from casing with acid. This tool was dropped to a seating ring installed on the tubing and could be retrieved by reverse circulation or wire line. In this process, the fluids were directed against the formation to clean and penetrate beyond the mud-damaged area. After the development of the hydraulic fracturing process, interest in jetting the formation with abrasive-laden fluid was renewed. The cutting action of abrasive fluid on pumping equipment, which is a well known problem, has been utilized to perforate and undercut casing, tubing and formation. In this process, surface areas are provided in the formation on which the frac- turing pressures may work to produce a fracture at the location desired. EQUIPMENT The tools used consist of bodies containing two, three or four jets in a single horizontal plane equally spaced around the circumference. The body is threaded to the end of a string of tubing and run into the well. In addition, an expendable tool is available that may be left in the hole after perforating and produced through until necessary to remove the tubing. The bottom of each tool is equipped with a ball-type back-pressure valve. The ball can be reversed to the surface and recovered. This allows reverse circulation so that loose sand which accumulated below the tool while jetting may be removed before the fracturing job. The present jetting tools are of such length that, when screwed together, the jets fall on 12-in. spacing. ANALYSIS OF THE PROBLEM Early work with nozzles indicated that hardened steel was not a suitable material for jets and that more durable material would be required. Ceramics were tried and found to be superior to steel but still too shortlived for most applications. Tungsten carbide, which was tried and found to be the best material available, is now being used for jet nozzles. Analysis of the problems presented by this process indicated that the following information was needed. 1. The effect of submergence on a jet stream and the effect of submergence on the cutting rate of a jet stream. 2. The cutting rate and depth of a jet stream in steel. 3. The cutting rate in various formations and point of diminishing returns. 4. Size of hole or slot cut in a pipe by a given jet. 5. Fluids and sands used. 6. The flow of various weight fluids through the jet nozzle and the discharge coefficients. 7. The type cut formed in the formation by the jet stream. 8. The stretch and contraction of tubing due to temperature and pressure. The cutting effect of a jet stream on a target in the atmosphere is rapid and spectacular as most of the

By W. R. Hibbard Jr., R. W. Guard, N. G. Ainslie

Evidence is presented that copper-base solid solutions of different solutes having equal grain sizes, no preferred crystal-lographic orientation, equal electron-atom ratios, and, within experimental scatter, identical initial yield strengths, need not have identical stress-strain curves at strains larger than about 0.04. The stress-strain behavior is rationalized in terms of the proposed Suzuki chemical interaction between solute atoms and extended dislocations using what is thought to be a somewhat different means of representing stress-strain data. ALTHOUGH the effect: of alloying element upon the strength characteristics of sold solutions is a subject which has received considerable attention in the past, the exact relationships between the common deformation parameters and certain common variables are not really known in some cases. As a result some of the experiments reported in the literature in which these variables are inadequately controlled lose some of their persuasion regarding underlying principles. Nonetheless, facts are known which bear pointing up: When the true stress, a, and true plastic strain, E, of tensile deformatic~n are plotted on a double logarithmic coordinate system, one may observe a straight-line relationship at strains greater than 0.02. The form of the curve in the linear region is given by a = Ken! where a represents true stress, E, true strain, and K and tn, constants. If the relationship holds, K and m define the flow characteristics of the material being tested. m and K, however, may vary with other parameters. Hollomon found that in a-brass, m is influenced by grain size. French and HibbardZ found in alloys of copper that inverse relationships existed between m and 1) the solute concentration for a given solute, 2) the 0.01 yield strength, and 3) the constantK. Lacy and Gensamer3 observed (du/d~) (= U/Em) to increase with increasing values of K in systems of alloyed ferrites (although with considerable scatter of data which may be attributed to uncontrolled grain size). Brick, Martin, and Angier* deduced in copper-base alloys a straight-line relationship (with some scatter) between the change in the Dph number due to solid-solution strengthening and the change in the Dph number due to work hardening which suggested that copper-base alloys having equal yield strengths might have identical stress-strain curves in the plastic flow regions. French and HibbardZ concluded that the yield strength of copper-base solid solutions is the proper basis for comparing the effects of solute elements. Also, Allen, Schofield, and ate&apos; showed that, within their experimental variation, copper-base alloys of zinc, gallium, germanium, and arsenic having the same electron-atom ratios have the same true-stress true-plastic strain curves. Dorn, Pietrokowsky, and ~ietz&apos; also found that with aluminum-base alloys the stress-strain curves in the flow regions are approximately the same if "equivalent" concentrations of alloying elements are used. Solute valence and lattice parameter distortion were the parameters used to determine equivalency. The present report describes an investigation in which an attempt was made to obtain copper-base solid-solution alloys of four solute elements having within close tolerances equal grain sizes and yield strengths, and to see if the level of yield strength does indeed define the flow curve regardless of solute type. During analysis of the data certain unexpected features of the stress-strain curves became apparent which gave rise to some speculation and are discussed at length in the paragraphs that follow. EXPERIMENTAL PROCEDURES Alloy Preparation—Using the data of French and HibbardZ as a first approximation, four different binary copper-base alioys were designed so as to have the same yield strength. In addition, other alloys were prepared in which the solute aoncentrations varied slightly from those calculated above so as to span a range of yield strengths, see Table L The yield strengths of all alloys prepared except the copper-tin alloys were subsequently found to Lie fairly close to one another. The copper used in the alloys was produced by the American Smelting and Refining Co. and was of very high purity (99.999 pct). The alloy additions and their initial purities are as follows:

Jan 1, 1960

By C. B. Sclar and

A graphical solution is presented for the equation v =v &-cU where vb is the volume of liquid b of density 6 that must be added to liquid a of volume va and density d, in order to obtain a heavy-liquid solution of preferred density dm for mineral fractionation. The equation is valid only for pairs of liquids whose volumes are additive, but empirical density-composi-tion data show that this condition is met over wide compositional ranges by all of the heavy solutions that are commonly used for mineralogical analysis. The chart is a nomograph which consists of two horizontal volume scales ad a vertical density scale arranged so that one volume scale occurs on each side of the density scale. All the scales are linear. For two liquids of density d, and &, respectively, each volume scale has an independent level on the density scale, ad the graphical solution for vb on the nomograph is obtained by construction of one straight line. The chart can be prepared easily to cover any density range with any desired accuracy by proper selection of the scales. Heavy-liquid separation of particulate samples is an indispensable analytical procedure in the mineralogical and mineral-process ing laboratory. Heavy liquids may be used 1) to isolate specific minerals in the form of high purity products or to fractionate samples into several products with density limits for petrographic, chemical, spectrographic, and X-ray diffraction analysis,&apos;-&apos; 2) to determine the density of minerals,&apos;-l4 3) to facilitate the recognition and identification of optically similar associated minerals,15 and 4) to determine quantitatively the degree of liberation of ore minerals in ores and mill products at various limiting sizes." The preparation and recovery of heavy liquids suitable for mineralogical analysis are discussed fully in the literature and operational procedures and special equipment for heavy-liquid separation are described in numerous references.&apos;747837&apos; 13,18,25-42 Useful tabulations of heavy liquids for mineralogical analysis are given by Tickell, Mil-ner,&apos; Twenhofel and Tyler,&apos; and Lange and a very complete up-to-date list of minerals arranged according to increasing density is given by Mursky and Thompson. USEFULNESS OF THE DENSITY CHART For any particulate sample, the limiting densities selected for its fractionation by means of heavy- liquid separation depend on the respective densities of the constituent minerals and the specific objectives of the separation. In many instances, the densities of readily available and practicable heavy liquids do not coincide with those that are required, and suitable liquids of the proper density are obtained by dilution with miscible liquids. In the general case, one may wish to mix either a pure liquid (A) or a solution of two miscible liquids (AP,,) of known density with either a pure liquid (B) or a different solution of the two miscible liquids (A,B,) of higher or lower density in order to obtain a final liquid of the preferred density. In conventional practice, the latter is reached empirically by trial-and-error addition of increments of one liquid to the other. The density of the final solution may be determined either by accurately weighing a known volume of the final liquid,&apos;&apos; 532;4;40, or by means of I)a Westphal balance, 2)a hydrometer, a refractometer in the case of binary liquid systems for which density-refractive index data are available,15 4) natural or synthetic .indicators of known density, a pycno-meter. Like all trial-and-error methods, these procedures are time consuming and many require special equipment which may not be available, The purpose of this paper is to show that the volume of a liquid of known density which is to be added to another liquid of known volume and density in order to obtain a solution with an intermediate preferred density may be determined rapidly and accurately by a graphical method provided that the two liquids form ideal or quasi-ideal solutions whose volumes are additive. Empirical data47&apos;8~&apos;8~4B&apos;49 show that solutions prepared from pairs of miscible

Jan 1, 1961

By F. V. Lenel, G. S. Ansell, J. A. Dromsky

The growth of aluminum oxide particles in a nickel matrix was studied eve?. the temperature vange of 2140° to 2470°F. The instability of the dispersed alumina was shown to be independent of the crystal structure of the alumina. The activation energy for the growth of the dispersed alumina was found to be 84.7 1 2.0 kcal. The particle radius increased as a function of time. These results indicate that the growth is not diffusion controlled. It is believed that the rate controlling mechanism is the dissolution of the aluminum and oxygen atoms into the nickel lattice. THE strength properties of alloys which consist of a finely dispersed second phase in a metallic matrix depend upon the spacing between the second phase particles. It is therefore desirable to achieve very fine dispersions in these alloys. Furthermore, to retain the properties these very fine dispersions must be stable during fabrication and service of the alloys. The best known of the dispersion strengthened materials, the SAP type alloys, which consist of a dispersion of aluminurn oxide in aluminum, have exceptionally good stability up to the melting point of aluminum. There is evidence, however, that other dispersion strengthened alloys, even those consisting of refractory oxides in a metal matrix, may be less stable. This investigation is concerned with the stability of Ni-Al2O3 alloys in the temperature range in which these alloys are usually fabricated. The mechanical properties of Ni-Al2O3 alloys at elevated temperatures have been previously investigated by Crelnens and rant,&apos; and Gregory and Goetzel.2 The behavior of these alloys in stress rupture tests appears to indicate that at temperatures below 1800°F they are highly stable. There is some doubt, however, as to their stability at the higher temperatures used during the conventional fabrication. Cremens and Grant, in preparing their test alloys, cousolidated, by powder metallurgical techniques, nickel powders as fine as 0.13 µ diam and alumina powders as fine as 0.018 µ. Metallo- graphic examination of the alloys following fabrication revealed that none had interparticle spacings of less than 2 µ. Considering the size of the original component powder particles, it is likely that the dispersions coarsened during fabrication. Gregory and Goetzel, in their studies of extruded alloys of 80 pct Ni—-20 pct Cr matrixes with nonmetallic dispersion, observed a definite coarsening of the alumina dispersions in alloys sintered at 2280°F as cantrasted to those sintered at 2000oF. Similar observations on the spheroidization and growth of thoria particles finely dispersed in a nickel matrix were made by D. K. Worn and S. F. Marton.3 As a result of such coarsening, much of the effort expended in the preparation of very fine powder mixtures would be lost. The mechanical properties of the alloys which had experienced coarsening would be expected to be poorer than if the original dispersions had been retained. EXPERIMENTAL PROCEDURE Ni-Al2O3 alloys were produced from powder prepared by a coprecipitation technique. Aluminum hydroxide and nickel hydroxide were coprecipitated from chloride solutions of the metals. The mixed hydroxides were calcined to form metal oxides and the nickel oxide in the mixture was selectively reduced to nickel by treating it in hydrogen. Specimens were compacted from the resultant powder which consisted of a fine, uniform mixture of aluminum oxide and nickel particles. The compacts were sintered by resistance hot pressing4, a densification technique which requires exposure times of the order of only a second or less at elevated temperatures. A conventional sintering process was not used, since the temperature required for densification would have to be in the region in which the stability of the dispersion was to be studied. A series of hot pressed specimens were treated in hydrogen at temperatures from 2140o to 2470°F (1171o to 1355oC, for times up to 120 hr. Changes in the microstructures were studied by electron microscopy using the two-stage preshadowed carbon replica method.5 In performing a lineal analysis on a series of micrographs from each specimen it was found more convenient to determine the mean free path between alumina particles rather than particle radii as the parameter of growth. Although these quantities are directly proportional for only spherical particles, the alumina particles in these alloys

Jan 1, 1962

By K. W. Smith, E. A. Thomas

Various grades of synthetic mullite have been developed in recent years to replace or supplement natural sources of mullite deriued from the mullite group of minerals consisting of sillimanite, kyanite, and andalusite. Raw materials and heat treating processes used in making synthetic mullite are described. Chemical and physical data are given for typical grades and crystalline structure is illustrated with micrographs. Use of synthetic mullite as a refractory material in the glass and metallurgical industries is discussed. Mullite (3A12O3.2siO2), the only stable compound formed in the alumina-silica system, is usually present to some degree in all aluminum silicate ceramic products. The formation of mullite is considered beneficial to give rigidity to the structure and is dependent upon the ratio of Al2O3 to SiO2 in the original composition, particle size, degree of mixing, firing temperature, cooling rate, and the presence of auxiliary glass-forming fluxes. Mullite may also be formed at the reaction interface of fire clay or alumina-type refractories in contact with glass or slag melts. The term synthetic mullite is commonly used today to identify a class of sintered and fused aggregates or grains in the alumina-silica system having a highly developed mullite structure but derived mainly from raw materials other than the sillimanite group of minerals. Within the past 15 years extensive research has been done to develop economical processes to form sintered synthetic mullite aggregate to replace calcined Indian kyanite in super-refractories. Severa1 brands of such mullite are now being produced in commerical quantity and finding extensive use in refractories. Based on the service results of such refractories in many applications throughout the metallurgical, ceramic, and glass industry these developments have been considered successful and suitable substitutes for Indian kyanite now appear assured. EARLY DEVELOPMENT The conversion of kyanite, sillimanite and anda-lusite minerals of the sillimanite group to mullite and their use in refractories and porcelain have been discussed quite extensively in the literature by peck,&apos; Grieg,&apos; Riddle and Foster,3 Bowen and Grieg,4 and others and will only be mentioned here for reference to compare properties with synthetic mullite. In 1928, curtis5 reported on the development of a high temperature gas-converter process for forming synthetic mullite. The raw materials were derived mainly from lumps of high alumina clay of the correct natural composition or blends of clays and alumina that was interground and briquetted to form a suitable charge to maintain a surface combustion firing within the converter. Curtis was, no doubt, the first to illustrate by micrographs in natural color the crystalline structure of mullite derived from kyanite and mullite derived by sintering clay and alumina mixtures at temperatures above cone 32 (3123°F) and by electric fusion. In 1937, sei16 was issued a patent covering the use of a mixture of alumina-silica minerals and alumina in the proportion to form a mullite-yielding material at temperatures in excess of 3100&apos; F. During the period from 1930 to 1940, economic conditions were not favorable for the production of synthetic mullite mainly due to an adequate supply of good grades of Indian kyanite ore suitable for conversion to mullite. Uncertain conditions on availability of the Indian kyanite during the early stages of World War II fostered further study on the development of synthetic substitutes. In 1943, McVay and wilson7 reported on an extensive investigation of domestic substitute materials. Their work covered essentially the use of mixtures of electric furnace mullite, calcined topaz, and calcined domestic kyanite. Compositions were found that gave equivalent or better hot load strength than Indian kyanite in mullite-type brick compositions; however, the calcining of the topaz presented certain physical and chemical problems on the disposition of silicofluoride and hydrofluoric acid while the high cost of electric furnace mullite was a limiting factor. In this work it was pointed out that water-quenched fused mullite was found to be unstable on reheat and gave poor hot load strength due to excessive glass present whereas the slow cooled or annealed mullite contained large crystals of mullite and corundum with little glass and gave superior results.

Jan 1, 1961