Search Documents

By J. L. Huitt, J. L. Pekarek, D. K. Lowe

In a theoretical study of hydraulic jetting, the velocity of the abrasive material relative to the velocity of the fluid in the jet stream is analyzed as the jet stream moves through the convergent and straight sections of the nozzle and the region between the nozzle exit and target. The results revealed that the abrasive material exits from the jet nozzle at a lower velocity than the fluid. The exit pmticle velocity can be increased by increasing either the density of the fluid or the length of the nozzle, and/ or decreasing either the particle density or particle diameter. In the divergent jet stream, there exists a point after which the particle velocity exceeds that of the fluid. The relative velocities were considered in the derivation of an equation to predict cutting rate of a circumferential notch and maximum notch depth. Data of a general nature and data which substantiate the theoretical results were obtained experimentally. INTRODUCTION The use of a fluid containing an abrasive material has been an established technique for cleaning and cutting for many years. In the petroleum industry, the early effort to use this technique1 to perforate and/or to overcome wellbore damage met with only limited acceptance because of the short life of the jet nozzle. With the introduction of improved perforating techniques, and later, hydraulic fracturing, the use of hydraulic jetting as a well completion technique became even less appreciated. It was only in recent years that interest in hydraulic jetting was revived. Once this interest was revived, the results of surface tests stimulated the interest of the industry even more than the state of the technology probably warranted because many of the tests were not appropriate for down-hole conditions. However, because of the stimulated interest, the development of the jet nozzle progressed very rapidly to the point where the nozzle life was no longer a prob- lem. With this accomplished, the use of hydraulic jetting in well completion became an accepted practice in a short time. The purpose of this paper is to present a theoretical analysis of the hydraulic jet stream as it passes through the nozzle and travels to its target. With a better understanding of the jet stream and the effects of various parameters, the performance of the process can be predicted more accurately. Equations are presented for cutting rate as applied to circumferential wellbore notching that relate the jet stream make-up, notch configuration and formation material. Also, experimental data are presented on some factors pertinent to hydraulic notching that are not theoretically analyzed. RELATED STUDIES Most of the studiesl-5 reported in the recent literature have pertained to the more practical aspects of hydraulic jetting; i.e., the effects of certain parameters as interpreted from experimental results, and the application of hydraulic jetting in well completion. In reviewing the effects of various parameters, it is interesting to note the reported depths of penetration obtained under various imposed conditions. In general, the depths vary from a few inches to several feet; however, a depth of penetration of less than 6 in., as reported by Thompson,4 seems more realistic for the usual field practice of hydraulic jetting with sand in water for a period of 20 to 30 minutes. In addition to the practical aspects, the study of Brown and Loper5 included a theoretical approach to hydraulic jetting. Their study resulted in the development of a theoretical expression for the maximum depth of penetration if jetting were continued for an infinite time. An analysis of the equations presented reveals that the initial cutting rate is infinite. The equation expressing centerline velocity is that of Forstall and Gaylord,6 which is applicable for a jet stream exiting in a large stationary medium. Since practically all of the fluid pumped into a perforation (or cut) must flow back through the perforation prior to re-entering the wellbore, a description of the medium as finite and non-stationary seems more reasonable. Thus, in this

By H. C. H. Darley

The influence of particle size and concentration on the development of chip hold-down pressure (CHDP) was studied in an apparatus designed to measure the change of filtration rate during the first second of the filtration process. CHDP is controlled by the "bridging" particles (i.e., particles in the 50 to 0.2 micron range), whereas filter loss is controlled by the colloid fraction. The results indicated that a fast drilling fluid with a low filter loss could be obtained if the concentration of bridging solids and the viscosity were kept very low. A novel group of drilling fluids, which we have named colloid emulsions, was developed to meet the above requirements. These colloid emulsions are made by dispersing art oleophilic colloid in oil and emulsifying about 5 per cent of this dispersion in water or a dense brine. Good results have been obtained in field trials with emulsions which use asphalt as the oleophilic colloid. INTRODUCTION In recent years it has been found that fast rates of penetration can be maintained in hard formations by using "clear" water as a drilling fluid. In some cases, however, water cannot be used because the very high down-hole filter loss creates various difficulties in drilling, in logging, or in producing the well. It then becomes necessary to "mud up", which results in a decrease in drilling rate. The reason that mud decreases drilling rates is a complex subject which has been well covered by such authors as Garnier and van Lingen, Cunningham and Eenink,' and van Lingen.3 One of the principal factors involved is the tendency of the drilling fluid to develop a filter cake on the bottom of the hole. The pressure differential which develops across this filter cake opposes the action of the bit in dislodging chips from the rock. This pressure differential is referred to by Garnier and van Lingen' as the chip hold-down pressure, which is denoted by the initials CHDP in this paper. The work described in this paper was undertaken to develop a drilling fluid which would minimize CHDP but which would still have a low filter loss—in other words, a fluid which would deposit a filter cake on the sides but would lay little or no filter cake on the bottom of the hole. EVALUATION OF CHDP EXPERIMENTAL Conditions governing the growth of filter cake on the sides of the hole are obviously different from those on the bottom of the hole. On the sides of the hole, cake will form continuously but at a decreasing rate, until eventually the rate of growth will equal the rate of cake erosion by the mud stream.' On the bottom of the hole, each time a bit tooth dislodges a chip the cake is removed, a fresh rock surface is exposed, and the filtration process must start over again. Thus the CHDP is determined by the amount of cake which can form in the interval between successive tooth strikes at a particular spot, normally a fraction of a second. Our first step therefore was to study filtration rates over the first second or so of the filtration process. These tests were conducted in the simple type of dynamic filter cell shown in Figs. 1 and 2. In this cell the mud was filtered through a train of rock cores while rotating blades kept the mud flowing over the surface of the core. The procedure was to evacuate the cores to 0.05 mm of mercury, saturate with brine, and assemble in the holder under brine. The permeability of the core train was then determined. A plastic seal was placed on the face of the core train, and a rip cord was attached from the seal to one of the blades. At the start of the test, 500 psi was applied to the mud, and the meniscus in the capillary measuring tube was adjusted to zero. When the blades were started, t,he seal was ripped from the face of the core, and filtration began. The filtration rate was at first measured by photographing the advance of the meniscus in the capillary tube. Using

Jan 1, 1966

By J. W. Goss, M. J. Coolbaugh

Most grouting has been done to stop water flaw in mines and for stabilizing foundations of various man-made structures, a survey of the U.S. literature reveals. Apparently Sun Manuel is one of the first mines in this country to use grout extensively underground for strengthening and stabilizing ground in drifts, shafts, and stations. A comparison with other procedures as well as details of the Sun Manuel program are covered. The employment of pressure grouting as a ground stabilizer at the San Manuel Copper Corp. mine reduces delays in both development and production, lowers costs, and makes possible safer working conditions. It specifically reduces delays in haulage operations and permits the maintenance of normal ventilation. In development work this grouting allows faster excavation by cementing together highly fractured or broken ground that otherwise would require extensive cribbing or spiling. In drift repair, it consolidates the loose or fractured rock over the timber or steel drift supports, thus decreasing the frequency of repair, lessening the hazards from falling rock, and curtailing delays due to blockage of drifts by muckpiles and repair operations. Pressure grouting is the process of pumping an accurately controlled mixture of cement and water into loose, fractured, or porous rock. The ratio of water to cement varies according to the nature of the rock encountered, from the thinnest mixture of 30 gal of water per sack of cement, used to fill very fine fissures, to very thick grout of 5 gal of water per sack of cement, used to fill large fissures or extensive areas of loose, broken rock. The pumping pressures at San Manuel vary from about 100 to 1000 psi, depending upon the compactness of the rock, while at other mines the pressures sometimes go as high as 5000 psi. In order to grout an area in which ground water is encountered, the pumping pressure of the grout must be increased by an amount equal to the pressure of the ground water. GROUTING IN DEVELOPMENT WORK The areas under development at San Manuel include many sections of loose, highly fractured rock. Prior to the advent of the grouting program, drifts, shafts, and stations in these areas could not be excavated without utilizing extensive support such as cribbing, spiling, and breast boarding. This slowed down the development work and increased the costs considerably over that required for excavating in more competent ground. Now, when a particularly bad area is contacted, the mining is temporarily stopped while the bad portion of drift or shaft is grouted. After the grouting is completed, the excavating is resumed with an approximate decrease of 50 pct in lost time and costs. Grouting in Drifts and Turnouts: The grouting procedures and patterns used in drifts and turnouts are very similar. The standard procedure for grouting such a turnout is shown in Fig. 1. After the ground is supported as well as possible with cribbing or lagging, the gaps between the back lagging and side lagging are plugged with empty cement sacks or additional timber, if necessary. The ground surrounding the proposed turnout is then grouted in two stages. In the first stage, the broken and caved rock is drilled and grouted to a depth of 5 to 10 ft, depending on the depth of the broken rock. This stage forms a grouted seal that allows higher pressures to be used at depths beyond 10 ft without developing excessive leaks at the face. After a grout hole is drilled, a 10-ft long pipe is wedged tightly into it with empty cement sacks. Grout is then pumped into the hole until the pressure reaches 200 to 300 psi, and the pipe is subsequently removed if it hasn't become cemented in. No more than one hole at a time is drilled and grouted because the grout has a tendency to go from one hole into another, plugging up the latter. Five or six holes are usually adequate for the first 10 ft of grouting. Experience has shown bentonite to be a useful admixture to the grout, particularly when it is indicated that the grout is being lost into large fissures or voids. Bentonite increases the plasticity of the grout enabling it to remain in place more easily until it has begun to set. In the second stage, the longer holes are drilled through the previously grouted rock, after which the

Jan 1, 1961

By L. E. Murr, P. J. Smith

A study has been made by transmission electron microscopy of thin foils of 304 stainless steel fatigued external to the electron microscope in reversed bending, and of thin foils fatigued directly within the microscope in alternating tension. The build-up of stacking faults in the thin foils during fatigue zoas correlated with the dislocatirm structures found in thin films prepared fror fatigued bulk specimens. The performance of the special devices designed for fatigue of thin foils so outlined and the importance of alternative methods of preparation of more uniform fatigue specimens bY vapor deposition are emphasized. INVESTIGATIONS on fatigued bulk aluminum1,' and stainless stee13j4 have revealed the existence of dislocation substructure on examination by transmission electron microscopy of electrolytically thinned foils representative of these bulk specimens. While this technique has proved extremely valuable, it has several shortcomings. First, the method of fatiguing bulk specimens and then thinning to foil for electron-transmission observation allows only one observation of internal structure at any one portion of the fatigue life. Second, thinning the bulk fatigued specimens to foil results in the loss of at least one original surface. Thus, what one sees in the remaining electron-transparent sections is an internal dislocation or fault structure which in many cases cannot be correlated with the original surface markings. This is an undesirable feature, since it is well-known that metal surfaces play an important part in the fatigue process.5 An obvious third undesirable feature of the thinning-from-bulk technique is the fact that static observations have difficulty (in the case of fatigue) explaining the mechanism of a dynamic process. What is required then is a method whereby a selected thin area can be continuously observed either while undergoing cyclic deformation or at various fixed stages of fatigue deformation. While Murr and wilkov6 have reported some success with an apparatus designed to fatigue thin metal foils directly within the electron microscope, the nature of the specimen-mounting procedure and the mechanical features involved in the adaptation of the fatigue device to the electron microscope make this method difficult to operate. It was not possible, for example, to make frequent observations of a selected area because of difficulty in maintaining a chosen area in a stable viewing position inside the electron microscope. Except for the build-up of a dislocation substructure and what are commonly referred to as "slip striations", little else has been reported from observations on thin-foil sections prepared from bulk fatigue specimens. segal17 has found "slip striations" in stainless-steel fatigued specimens which were electropolished from both sides, but gave no explanation as to their origin or identity in terms of lattice imperfections. The research to be reported in this paper was undertaken with the following objectives in mind. First, an attempt was made to devise a technique or techniques whereby thin metal foils could be fatigued and repeatedly observed by transmission electron microscopy. Second, it was hoped that some correlation could be made between deformation striations found in fatigued thin transmission specimens and thin foils prepared from bulk fatigued specimens. These investigations illustrate quite convincingly that a feasible method is available for the direct study of the fatigue mechanism and similar dynamic phenomena in thin transmission specimens inside the electron microscope. I) EXPERIMENTAL METHODS Three modes of specimen fatigue and observation of fatigue damage were used. These involved fatigue of thin-foil specimens in a special arrangement external to the electron microscope and observation of a selected area at various stages in the fatigue life, the fatigue of thin-foil transmission specimens inside the electron microscope, and the fatigue of bulk specimens external to the electron microscope followed by thin-foil preparation for direct observation at predetermined stages. Design of the External Fatigue Clip and Specimen Holder for the Hitachi H.U.11 Electron Micro-scope. The purpose of the fatigue clip was to provide a reversed bending fatigue stress to a thin-foil transmission specimen outside the electron microscope. In order to accomplish this, a flat-bottomed, U-shaped brass clip was made as shown

Jan 1, 1965

By Leslie W. Austin

ROTARY kiln operators will agree that some of the most severe conditions a refractory must stand occur in the hot zone of a kiln burning Portland cement, dead burn dolomite, magnesite, periclase, and similar materials. Frequently the operator is faced with factors beyond his control which drastically shorten the life of refractories. Shutdown due to mechanical failure can be serious if the period is of sufficiently long duration to cause the dropping of coating or the loosening of the lining. A change in slurry can affect the coating and cause ring buildup. A change in type of fuel and its effect upon the flame can cause a shift in location of the hottest zone. Weekend shutdowns or any other interruption can cause the operator trouble and may damage the refractories, since stopping and starting a rotary kiln is certainly more difficult than stopping and starting a motor. Some operators have tried to set an estimate of damage for each shutdown in equivalent days of running time. Conditions affecting the refractory may be roughly grouped in four classes: chemical attack, mechanical stress, thermal shock, and abrasion. Chemical Attack: The drive to obtain maximum production through a kiln demands maximum operating temperatures, temperatures which are limited more by the ringing up or melting of the clinker. This can cause interface temperatures at the junction of coating and refractory which require the use of a basic kiln block to withstand the chemical attack. Chemical changes take place within the refractory itself, especially in chemically bonded or unburned kiln blocks: These changes cause the formation of the ceramic or burned bond. Migrating liquids or fluxes from the kiln charge have an effect within the refractory and lead to mineral or glass formation. The alkalies, sodium and potassium, migrate into the refractory as silicates, chlorides, sulphates or other salts. They may move under capillary action or may be caused to move by volatilization with condensation in the cooler portion. Mechanical Stress: Concentrated stress may be caused by several factors or combinations thereof. 1-The rings of refractories must be kept tight and rigid within the kiln, and this alone demands considerable force to hold the blocks in place. So that the force will not be concentrated, the blocks should fit the circle as perfectly as possible, with the faces in contact overall. 2-As the kiln is heated, thermal expansion takes place at the hot end of the kiln block. Since this disturbs the plane face it too can cause a concentrated stress at the two ends of the block, and shearing stress can be set up within the brick itself because of the difference in expansion between the two ends. 3-If a lining becomes loose and moves in the shell very severe stress can be set up, and as the kiln rotates this load changes and gives the effect of repeated loading. Permanent expansion of the refractory can also cause severe loading. 4-Not least important, flexing of the kiln is frequently the cause of concentrated stresses. Thermal Shock: Thermal shock, the result of heating and cooling too rapidly, occurs on starting and stopping or when a large patch of coating drops, exposing the bricks. Again, its destructive effect is often the result of phase change, liquid to solid or the reverse; dense refractories loaded with glass-forming impurities are particularly susceptible. Thermal shock is a problem with refractories set in the wall or roof of a stationary furnace, and becomes even more serious in a rotary kiln, the tendency to spall being magnified with movement and concentration of stress. Uniform rate of feed and loading insures both better coating and a more uniform stress. Abrasion: If the refractories do not take a coating, abrasion can become a most destructive factor. Movement of the lining in shell or movement of loose blocks causes abrasion, which is also most destructive if the refractories do not take a coating. An analysis of the problem of basic lining for the hot zone reveals, therefore, a number of desirable characteristics: high refractoriness, basic chemical reaction, resistance to spalling, good strength at all stages, ability to take coating, true sizing, volume stability, and abrasion resistance. Increased demand

Jan 1, 1952

By W. O. Philbrook, H. W. Hosking, N. B. Melcher

A simple and inexpensive mercury-tracer method has been develohed to study rates and Patterns of gas flow in blast furnaces. A Pulse of mercury is injected into the hot blast, and its arrival at the sampling Point is recorded by an electronic circuit that measures resonant absorbtion of ultraviolet light by mercury vapor in the gas aspirated .through the detecting. cell. A rapidly developing interest in blast-furnace technology in recent years has created a strong demand for precise knowledge of the rates and patterns of gas movement through the stock column. Classical fluid-flow theory cannot supply the desired information because the complexity of the blast-furnace situation precludes the accurate determination of many of the parameters required for solution of the equations. In fact some of the terms employed in fluid-flow treatments become almost meaningless under blast-furnace conditions. The void fraction of the stock column, for example, varies widely from place to place and is affected by the segregation of charge materials, attrition of lumps during descent, and channeling. Gas density varies with changes in local pressure, temperature, and composition, while viscosity varies with temperature and composition. Even if mean values for these functions were acceptable, they would be either impossible or extremely difficult to determine with a high degree of accuracy since the value of the mean for all gas properties would depend upon the flow distribution itself. Attempts to study gas movement by the pitot-tube determination of kinetic pressures have met with little acceptance. Reproducibility of results is extremely difficult to achieve in a situation where alignment of the tube orifice with respect to the flow direction in tortuous channels cannot be guaranteed. Because of these difficulties it would appear that progress can be achieved only with a direct method of measuring gas velocities and determining the shape of flow paths through the stock. The establishment of such a method is described in this paper. SELECTION OF METHOD Direct measurement suggests the use of a tracer by means of which the progress of a "parcel" of gas can be followed through the furnace. Several requirements must be met before any selected material can be considered a suitable tracer. First of all, it must be a substance not normally present in blastfurnace gas or dust; otherwise its presence in a gas sample will have little significance. It should be volatile at temperatures normally existing within the furnace, to ensure that it will travel with the gas, as a gas. It should possess special properties enabling its presence in the gas to be detected readily, and it should not undergo exchange reactions with any material normally present within the furnace, including refractories and coke as well as all components of the metal and slag. Radioactive materials naturally are considered because their radioactivity renders them susceptible to detection. However, of the many radioactive materials available, almost all are eliminated from final consideration by their unsuitability in terms of other properties. Radioactive silicon, carbon, calcium, phosphorus, and many others have been considered and discarded, either because they are not volatile over the whole range of significant temperatures, or because they could be expected to undergo exchange reactions with burden or refractory materials. Others which might be suitable in terms of these properties are eliminated because of a low activity, short half life, or the necessity for fragile counting apparatus. Of the many elements available in radioactive form, perhaps radon is the only one suitable for blast-furnace gas-flow studies. This has been used in several investigations1-4 with considerable success. The use of radiotracers has certain inherent disadvantages. One is the cost. An appreciable sum must be allowed for materials each time a test is made. Also, special methods of handling must be employed, and very often the progress of an investigation must be governed by the availability of isotopes and the delivery arrangements that can be made for them. An advantage is immediately gained if the tracer material can be a substance which can

Jan 1, 1960

By J. L. Walter, W. R. Hibbard

A GREAT deal of work has been done on the rolling of single crystals of iron. Barrett and evensoon studied end orientations of heavily cold-rolled iron crystals and found that some crystals maintained a sharp single orientation during rolling. Others rotated into two or more orientations, and some fragmented and approached the entire polycrystalline texture depending on the original orientation of both the normal and rolling directions. Barrett, Ansel, and Mehl2 studied iron-silicon alloys and found that the addition of silicon to the iron had little effect on heavily rolled polycrystalline material. Dunn3 has extensively studied the cold-rolling and recrystallization of silicon-iron single crystals. Dunn found that for single crystals having initial orientation between (110) [001] and (111) [112], the principalcomponent of the cold-rolled texture is (111) [112]. Koh and Dunn4 studied the cold-rolled textures of single crystals having initial orientations in the range (001) [110] to (111) [IT01 and found that these are stable end orientations. They also found that all orientations having a [110] direction parallel to the transverse direction rotate to either the (001) [110] or the (111) [112] stable end orientation except for orientations near (112) [11], which divide and produce a final texture consisting of (001) [110]and (111) [112] components. Crystals having a (111) <112>-type texture re-crystallized to a (120) [001] or (110) [001]-type texture. Crystals having orientations with a range of (001) to (335) in the rolling plane and [110] in the rolling direction recrystallized5 to a wide spread of the initial orientations resulting from a multiplicity of 30-deg rotations about several (110) poles. The present study was undertaken to relate other orientations of crystals of silicon-iron to their cold-rolling and recrystallization textures, so that one might rationalize polycrystalline recrystallization data on the basis of the known deformation texture and the behavior of single crystals in these orientations. PROCEDURE Samples were obtained from a cylindrical ingot of 3 pct silicon iron prepared as follows: Armco iron was melted with high-purity silicon flakes under an atmosphere of argon to minimize oxidation. The alloy was poured into a special mold to form an ingot which consisted partially of large columnar crystals. Plates were cut from the columnar portions of the ingot with the longitudinal direction parallel to the columnar axes and ground to 0.040 in. thick. The plates were heavily etched to a thickness of 0.032 in. to remove the cold-worked surface. Orientations of seventeen crystals were determined by Laue back-reflection techniques keeping the mean columnar axis as the reference direction. The plate was then cut in two, parallel to the columnar axis. One portion of the plate was rolled at room temperature parallel to the columnar axis to a reduction in thickness of 84 pct. The remaining portion of the plate was rolled also at room temperature across the columnar axis to a reduction of 66 pct, at which point the crystals began to separate at the boundaries. After rolling, nine individual crystals were removed from the strip by cutting along the crystal boundaries with a jeweler&apos;s saw. Fig. 1 shows the original orientations of the six crystals that were straight-rolled and of the three crystals (4, 7, and 8) that were cross-rolled. Each rolled crystal was carefully etched to approximately 0.002 in. thick. Textures of the cold-rolled crystals were determined by use of the diffractometer with a non-integrating sample holder. The pole figures were made for the (200) poles using molybdenum Ka radiation and were plotted by an automatic stereographic projection recorder.&apos; Spurious poles were determined by rerunning portions of the pole figures using strontium oxide to filter out the Ka radiation. The central portions of the pole figures have not been determined. The pole figures were completed to about 55 deg from the periphery at which point the sample holder interfered with passage of the beam. Following the determination of the cold-rolled

Jan 1, 1959

By M. R. Tek

A new method for correlating the data on multiphase flow through vertical pipe is presented. The correlation is based on a "two-phase f factor" concept which was developed and successfully applied to horizontal multiphase flow by Bertuzzi, Tek and Poettmann. Field data previously published on several flowing and gas-lift wells have been used as the basis for the developed correlation. The application of the method to actual two-phase flow problems indicate that this method is capable of predicting the pressure distribution in vertical multiphase flow strings well within the accuracy range usually desired for common engineering and design calculations. A new working chart developed for calculation of two-phase pressure gradients and a graphical step-by-step procedure for the computation of pressure distribution are presented along with an example problem. INTRODUCTION Multiphase flow through vertical pipe is encountered in many engineering installations. In petroleum, chemical process, nuclear engineering and many other industries, problems associated with simultaneous flow of two or more phases through vertical pipe have been of interest for a long time. This interest has increased considerably during recent years due to applications to new processes in petroleum production and refining and to problems of steam generation and heat removal from nuclear reactors. One prominent example of vertical two-phase flow is provided by the gas-lift process where oil, water and gas flow simultaneously. If the pressure profile in a gas-lift well can be predicted within reasonable accuracy, it would be possible to get good estimates of the power required to lift the oil, the optimum depth, the pressure and the rate at which to inject gas. Furthermore, the effect of production rate and tubing sizes on these quantities can be evaluated before any design decision is made on the installation and operation of the flow string. The majority of experimental work available in the literature deals with two-component systems where individual phase flow rates in and out of the pipe remain constant. The general problem of prediction of pressure drops in multiphase flow systems is very complicated. The co-existence of numerous flow patterns of widely different geometry and mechanism, conditions of surface instability and the nature of force fields acting upon the system are among the major difficulties commonly encountered. The classical approach of fluid dynamics which would be based upon the formulation and solution of Navier-Stokes equations has been found by many investigators completely devoid of any hope of success-—not only because of inherent nonlinearities but also because of insurmountable analytical difficulties standirng in the way of setting up the boundary conditions. The presence and effect of interfacial forces on mu1tiphase flow systems further complicate the theoretical approach. For these reasons, many investigators choose to adopt semi-empirical if not purely empirical approaches in order to obtain solutions of engineering utility. A prominent practical solution has been given by Poettmann and Carpenter&apos; in the form of an empirical correlation. In their paper, total flowing densities of fluids and solubility effects of gas in oil have been taken into account for the correlation of field data covering a wide range of operating conditions for oil wells. They treated the gas. oil and water as a single phase of combined propcrties and correlated the multiphase friction factor as a function of the product (pvd), i.e., density X velocity X diameter of the flow string. However, because the product (pvd) is dimensional while the frictior factor is dimensionless, the generality of their result&apos;s is somewhat restricted. It seems that the omission 01 viscosity effect may be one of the reasons for the scatter of data as shown in their correlation chart. The concepts of the "two-phase f factor" and the "two-phase Reynolds&apos; number function" were recently developed and successfully applied to correlate horizontal multphase flow by Bertuzzi, Tek and Poettmann.&apos; Recently, two new methods of correlation by Tek and Chan&apos; have been presented on simultaneous flow of liquid and gas through vertical pipe. These two methods of correlation and the working equations in field units necessary for their application are included in this paper. The extension of the conccpt of two-phasc Reynolds&apos; number function successfully developed for horizontal flow into vertical multiphase flow systems, development and evaluation of working charts permitting calculation of two-phase pressure gradients and

By K. Tangri, B. Swaroop

Simultaneous measurements of lattice (elastic) strain by X-ray line shift method and total strain with an electrical strain gage have been carried out on polycrystalli,ne nickel with the help of a specially designed tensometer attachment for the X-ray dif-fractometer. During the initial stages of deformation, the rate of increase in lattice strain closely follows the total strain until the plastic strain sets in. From then onwards, the two strains deviate from each other and with further increase in afiplied stress the rate of increase of lattice strain eventually decreases. Depending upon the mode of unloading, both compressive and tensile strains have been observed in nickel deformed up to 0.29 pct strain. These results have been explained on the basis of the effects of clustering of dislocations and also the production and behavior of point defects during loading and unloading, respectively. POLYCRYSTALS deformed plastically in a uniaxial tension test show residual lattice strains (hereafter referred to as RLS), which broaden the X-ray line profiles and shift their peak positions.&apos;&apos;4 It is known that uniform straining of a crystal lattice (macrostrain) produced movement of ddfraction line peaks, whereas nonuniform straining (microstrain) causes line broadening.= Though the nature and origin of RLS in deformed metals is not yet clearly understood, these are believed to be due to the presence of some form of a locked-up stress system. Several possible detailed interpretations6&apos;" of the stress system have been proposed by various workers and common to all these interpretations is the assumption that different parts of the aggregate have different tensile yield stresses; e.g., that a part A yields under a lower applied stress than a part B. Therefore, during the deformation process, the elastic strain in A will be less than that in B, and, after completion of deformation, B will tend to contract further than A but will be prevented from doing so by the restraining influence of A. Thus, when equilibrium is reached, A will be in compression while B is in tension. Although there is general agreement on the correctness of this argument, controversy still exists as to the exact nature of the parts A and B in a deformed metal. In an alternative approach to the creation of parts A and B, many other investigators have assumed that the RLS observed in unloaded specimens are in some way connected with the lack of proportionality between lattice strain and applied stress in the region above the yield stress." cullity13 has prepared a schematic summary of the results of previous workers, mainly Smith and Wood,2&apos;11 which suggests that, above the elastic limit, the lattice strain may increase less rapidly with respect to strain, or may even decrease with increase in applied stress. If the applied stress is then decreased, the lattice strain would decrease along a line parallel to the loading line in the elastic region and thus produce a compressive residual lattice strain after unloading. At equilibrium, to balance these compressive stresses? there would have to be regions under tensile stress which may well be the grain boundaries or the substructure walls formed during deformation. The present investigation was undertaken to gain a better understanding of the nature and origin of RLS and also to experimentally verify the salient features of this hypothesis. EXPERIMENTAL Stress and strain determinations were made with a specially constructed tensometer attachment for the X-ray diffractometer, Fig. 1: which permits the following measurements simultaneously on a sheet specimen under uniaxial tension at various stress levels during loading and unloading: a) lattice strains, E=. in a direction perpendicular to the direction of pulling (x direction) from shifts in X-ray line peak positions; b) the total strain, ex, in the direction of pulling. with the help of an electrical strain gage affixed to the back of the specimen directly below the area irradiated by X-rays: and c) the applied stress, with the help of a load cell which consisted of a calibrated stainless-steel sample of dimensions identical to those of the specimen under investigation, and to which it was coupled. Because of its high stacking fault energy.I4 nickel

Jan 1, 1970

By R. E. Jenkins

The Bell Canyon member of the Delaware Mountain group has yielded quite a large number of fields in which completion and production problems have been numerous and complex. Reserves are difficult to estimate due to the problem of evaluating the formation water saturation, and the feasibility of water flooding is questionable. Extensive laboratory investigations were undertaken to determine if normally measured rock and contained fluids properties could account for many of the peculiar characteristics of the formation. A statistical study or routine core-analysis data was made. Capillary-pressure data were obtained by several techniques. Fresh-water and brine permeabilities were measured and relative permeabilities of oil, water and gas were determined. Some qualitative wetta-bility tests were performed, and the petrography of a few thin sections was studied. The results of this work are presented, with typical or average data shown for each test. The permeability -to- water characteristic of the Delaware was found to be abnormally poor. Correlations of laboratory and field performance data indicate high water saturations in much of the formation. Pore geometry is highly uniform. INTRODUCTION The Delaware formation has undergone extensive exploration and development in the past few years. This has resulted in the discovery of quite a number of fields—producing oil for the most part. A large percentage of the productive wells have produced water along with the oil. Often there is no apparent pattern for the percentage of water cut experienced. In several instances vertical displacments of over 200 ft have been established between communicating wells in which the formation appears to be about the same, yet the structurally high wells yield a much higher water cut than the lower wells. Drill-stem tests have contributed little to well completion because they nearly always show small amounts of water (usually mud filtrate), regardless of what is produced later in the life of the well. Other formation evaluation methods have had no more than limited success in indicating ultimate productivity. Consequently, predicting the type of fluid productivity of Delaware wells has been very difficult. Hydraulic fracture treatments are almost universal, and unstimulated Delaware wells have not exhibited the productivity that normally would be expected of wells with the specific permeabilities encountered. Some operators have indicated that their Delaware wells need frequent re-stimulation. The uncertainty of reservoir water saturations reported for the Delaware has made difficult the task of evaluating oil in place in the reservoirs and estimating primary recovery. The unreliability of this data also will cause feasibility studies for water flooding or other secondary-recovery methods to be problematical. Several opinions have been voiced to explain why the Delaware performs as it does. Chronically poor well completions, dynamic water and tilted water tables, capillary inequi-libria, peculiar relative permeability characteristics and oil-wetness are among the suggested reasons. The dual purpose of this paper is (1) to describe the principal rock characteristics, and (2) to present an evaluation of those characteristics so that approaches can be made to explain the irrational behavior of wells completed in the Delaware. STUDY OF ROUTINE CORE-ANALYSIS DATA A statistical study of routine core-analysis data has been made to relate fundamental rock properties and characteristics of the formation to well productivity. For the most part, well production data were obtained from operators and augmented by production data from commercial information services. Only data which were available in detail and which were considered to be accurate were used. The core data used were obtained on samples from the perforated or open interval only and, thus, may not always represent the total productive interval in a well. All the core-analysis data included in this study are from the Bell Canyon member of the Delaware and were obtained by "plug-type" techniques, as opposed to whole-core or full-diameter techniques. Porosity values were obtained by the summation-of-fluids technique, permeability values are air permeabilities corrected for slippage to an equivalent liquid permeability, and the oil and water contents were determined by means of a high-temperature downdraft retort. All the procedures used are discussed at length in Ref. I. The core-analysis data were sorted

By H. L. Hartman

The drop tester has proved an invaluable tool for the investigation of percussion drilling in the laboratory in "slow motion". It has allowed the process of rock penetration by impact to be studied a single blow at a time. In the present work, the relation of cratering to indexing has been determined under conditions simulating those in the bottom of the hole at atmospheric pressure. Indexed blows form craters which are influenced by others adjacent to them. Two unique effects are involved: (1) the provision of additional free faces in proximity to the point of impact and (2) the creation of subsurface damage by the previous blow(s). Both have a pronounced influence on the volume of rock removed per blow, which governs the rate of penetration in actual drilling. The emphasis in this study was placed on determining effects of index distance and impact energy on crater volume when blows were struck on a previorusly "drilled" or damaged surface, a situation most representative of down-hole conditions. The results indicated that (I) the optimum index distance on a damaged surface is greater than on a fresh, undamaged rock surface; (2) the volume of rock broken at optimum index distance is about the same for both surface conditions with die-shaped chisels but tends to be greater on a cratered surface with wedges; (3) the optimum index distance and maximum crater volume are proportional to the energy level; (4) at a given energy level, the volume of rock broken by dies generally exceeds that by wedges; and (5) maximum crater volume varies, approximately, inversely with width of die but is nearly independent of included angle of wedge. INTRODUCTION This is the third of a series l,2 of papers reporting on one phase of a continuing program of drilling research being conducted in the Rock Mechanics Laboratory at The Pennsylvania State U. The phase under consideration is crater geometry — blow energy relations in percussion drilling. While the previous papers have discussed mainly craters produced by single blows, indexed-blow studies are the subject of this paper. The basic mechanism of drilling under study here — that of penetration of a chisel-shaped bit subjected to impact — is the one employed in probably 90 per cent of all rock drilling in mining, percussion drilling. It also forms the fundamental action in nearly all oil well drilling with the so-called rotary (roller-bit) method. Here, the action is more complex, however, and may in actuality comprise rotary-percussion drilling. Certainly, the down-hole air and mud hammer drills, which superimpose percussion on rotation, belong in this latter category. In any event, impact blows constitute one of the principal mechanisms in the vast majority of drilling, mining or petroleum, and it is essential in drilling research to study percussion in all its basic aspects. Percussion drilling can be simulated in the laboratory by means of an impact drop tester. Striking one blow at a time with chisel-shaped bits, the drop tester permits study of most of the parameters in the drilling process except blow frequency and the interrelationship of certain variables. Single-blow craters, the simplest to produce, allow the determination of basic relationships, such as volume vs blow energy; while indexed craters most closely resemble the action in real drilling and provide data for the establishment of optimum operating criteria. Indexed-blow craters are those which are influenced by others in proximity. The simplest case to visualize, and the one studied in detail here, is that in which a given crater is formed adjacent and parallel to a previous crater, such that the second crater breaks into the first. A more complex situation usually exists downhole, where indexing is achieved by rotation of a radial-winged or rolling-cutter bit. But, admittedly, the phenomenon of indexing is more likely to be understood eventually if it is first studied in its simplest form, that related to parallel craters. Limited research has been conducted on indexed blows. The most complete study was that by Simon, 3,4 who proposed universal indexing curves to relate the important variables. His work, however, was conducted entirely with rows of craters formed on a

By W. T. Weller

In Part I, a study of pressure build-up curves calculated for conditions under which both oil and gas flow led to the conclusion that the presence of a dispersed free gas phase in an oil reservoir must be taken into consideration to estimate accurately average reservoir pressure and permeability from build-up curves. Familiar methods based on the assumption of no free gas can be extended to the two-phase case by using total compressibility and mobility in place of single-fluid compressibility and mobility. These methods give correct values for average pressure and permeability when gas saturation is small. Errors become larger as the gas saturation increases. However, for the use to which the results will be put, the methods are satisfactory for reservoir engineering purposes. An improved method of calculating the performance of depletion-type reservoirs is presented in Part 2. Because the mathematical relationships describing simultaneous flow of oil and gas are quite involved. simplifying assumptions are made to provide means of obtaining approximate solutions of reasonable accuracy. One such approximate method now in use is the constant-GOR solution. It involves the assumption that at any instant, the ratio of total gas flow rate (both free and disolved) to oil flow rate is the same at all points in the reservoir. The approach is not applicable unless the free gar saturation in the reservoir is everywhere greater than the critical gas saturation. This paper presents a modification which, by avoiding the constant-GOR assumption, makes the method applicable to all reservoir conditions, and so far appears to be more accurate than the constant-GOR solution and to he comparable in required compuctation time. PART I— BUILD-UP CURVE ANALYSIS INTRODUCTION Pressure build-up characteristics of shut-in wells have been used for many years by engineers to evaluate average reservoir pressure, effective permeability thickness of the pay section, effectiveness of well completion (skin effect) and reservoir size. A number of methods of analysis have appeared from time to time."" Without exception, these methods are based on the assumption that the reservoir contains but one fluid of constant small compressibility and constant mobility. It has been suggesteda" hat these single-fluid methods may be applied to data from reservoirs containing both oil and gas by substitution of some effective total properties of the multiphase system in place of the corresponding single-phase properties. The present investigation was undertaken primarily to evaluate this approach. METHOD A number of theoretical build-up curves were calculated for conditions of two-phase flow, under the assumption of certain reservoir and fluid properties, and were analyzed by single-fluid methods with appropriate total compressibility and total mobility values for the corresponding single-fluid properties. Results of the analyses were compared with the assumed conditions. The theoretical build-up curves were completed by procedures similar to those of West, Garvin and Sheldon." Since these calculations require a considerable amount of computer time, an attempt was made to derive an approximate calculation method. The attempt was unsuccessful for calculating build-up curves, but the effort did result in a new approximate method of calculating the performance of solution gas drive reservoirs, which appears to be an improvement over the constant-GOR method" used previously (see Part 2). The West, Garvin and Sheldon calculations involved the following assumptions: (1) the reservoir is circular and completely bounded, with a completely penetrating well at its center; (2) the porous medium is uniform and iso-tropic, with a constant water saturation at all points; (3) gravity effects can be neglected; (4) compressibility of rock and water can be neglected; (5) the composition and equilibrium are constant for oil and gas; (6) the same pressure exists in both the oil phase and the gas phase; and (7) no afterproduction occurs, i.e., the well is shut in at the sand face for build-up. These assumptions make it possible to describe two-phase flow of oil and gas by the partial differential equations:

Jan 1, 1967

By J. E. Andersen, J. Halpern, C. S. Samis

In the presence of oxygen, galena is oxidized in an aqueous medium containing sodium hydroxide, in accordance with the following reaction: PbS + 2O2 + 3OH ? HPbO2 + SO4 = + H2O A novel method was devised for following this reaction which takes place in an autoclave under oxygen pressure, by measuring the concentration of HPbO2- in the solution with a cathode ray polarograph employing stationary platinum electrodes. Using this procedure a study was made of the kinetics of the reaction, in which the effect of a number of variables, including temperature, oxygen pressure, NaOH concentration, and agitation, on the rate, were determined. The results of this study are described and discussed, in terms of possible mechanisms for the reaction. IT is known that sulphide minerals can be oxidized in aqueous media in the presence of oxygen under pressure. Reactions of this type can be classified in two categories depending upon whether the products of oxidation are insoluble or soluble in the aqueous medium. An example of the first type of reaction is the oxidation of pyrite in alkaline solutions, giving rise to an insoluble iron oxide. The kinetics of this reaction have been investigated and its mechanism established.&apos; It has been applied in the oxidation of iron sulphides present in refractory gold ores to improve the subsequent recovery of gold by cyanida-tion.&apos; The second type of reaction finds application where it is desired to recover the metal by leaching during oxidation. In this case a medium is selected in which the oxidized mineral is soluble. For example, nickel, copper, and cobalt sulphide ores can be treated by oxidation in the presence of a solution of ammonia dissolving the nickel, copper, and cobalt as the metal ammine sulphate salts.:&apos; A similar treatment has also been reported to apply to zinc sulphide ores.&apos; It is known that lead sulphate is soluble in solutions of sodium hydroxide or ammonium acetate. It should therefore be possible to dissolve the lead from galena ores by aqueous oxidation with oxygen under pressure using either of these solutions. The applicability of the ammonium acetate treatment has been investigated and confirmed in a recent study.&apos; The present paper describes the results of a similar study in which the kinetics of the oxidation of galena in sodium hydroxide solutions have been investigated. The object of this investigation was pri- marily to obtain information of a fundamental nature relating to the kinetics and mechanism of this reaction. The use of pulps of comminuted ore in a study of this type is undesirable because of the difficulty in controlling and measuring the surface area. The measurements were therefore made using galena crystals of measured surface area and in this way absolute reaction rates were obtained. The reaction was found to proceed as follows: PbS + 2O2 + 3OH ? HPbO2 + SO4 + H2O [I] The products are sodium plumbite and sodium sulphate salts which dissolve in the aqueous solution. The reaction studies were carried out in an autoclave in which a desired pressure of oxygen was maintained. The reaction was followed by measuring the concentration of lead in the solution with a cathode ray polarograph. The results obtained in this investigation are presented and discussed in the present paper. Experimental Materials: The crystals of galena were obtained from Violamac Mines, Sandon, B. C. The following impurities were indicated by spectrographic analysis carried out by the Provincial Assay Office, Victoria, B. C.: Sn, 0.02 to 0.2 pct; Sb, 0.07 to 0.7; Zn, 0.01 to 0.1; Si, Fe, Mg, As, less than 0.05 pct; Ag, 126 oz per ton, the latter determined by standard fire-assaying procedure. After cutting a specimen measuring approximately 5x7x12 mm, the crystal surfaces were ground parallel to the 100 axes using No. 2 emery, washed with water, and the dimensions were measured with a micrometer. Oxygen gas was of commercial grade and supplied in cylinders by Canadian Liquid Air. Solutions were made up with chemicals of chemically pure grade and distilled water. Equipment: Autoclave: The autoclave used in these studies was constructed of stainless steel and

Jan 1, 1954

By J. L. Walter

Extra-low carbon iron sheet, when deformed and annealed, undergoes exaggerated or abnormal grain growth in the critically deformed regions of the sheet. This exaggerated pmth occurs, for low strains (3 to 6 pct), only in sheet which has a fine dispersion of precipitates in the subsurface region of the sheet and fewer and coarser precipitates in the sheet interior. These particles have been identified as manganese sulfides. Wing the anneal, grains near the surface are gvowth-inhibited by the fine particles but the grains in the interior are free to grow normally. With the additional driving force provided by the strain energy, the interior grains first grow into the small subsurface pains. Eventually, these growing grains grow completely through the sheet. Calculations of limiting grain sizes at various values of strain indicate that a volume fraction of precipitates in excess of 10-&apos; would be required to eliminate exaggerated growth in material strained to 10 pct. OPEN-COIL annealing has made decarburization of sheet steel both efficient and economically practical. Use of such material for porcelain-enameling stock is one of many possible applications of low-carbon iron since carbon in steel is deleterious to porcelain-enameling properties.&apos; However, the extra-low carbon iron presently available presents another problem, that of exaggerated grain growth in regions where the sheet has been deformed as by bending or stretching. In exaggerated grain growth a few grains start to absorb their neighbors and these may become very much larger than the average grains of the sheet. Other names for exaggerated grain growth are coarsening, critical grain growth, secondary recrystallization, abnormal grain growth, or discontinuous grain growth. While this grain growth does not affect the enameling qualities of the low-carbon iron sheet, their presence results in a marked reduction of tensile-yield strength in the region of the sheet containing the large grains. The loss of tensile yield strength may render the material unsuitable for many applications . This report describes the results of a study undertaken to determine the cause of the exaggerated grab growth in extra-1ow carbon iron and, if possi- ble, to prescribe practical procedures for its prevention. GENERAL THEORY The driving force for exaggerated grain growth is the grain boundary free energy. This driving force is proportional to (l/rl + l/r2) where rl and r2 are the mutually perpendicular radii of curvature of the boundary between the growing grain and the grain being consumed. Thus, the greater the difference in size between the growing grain and the matrix grains, the higher the driving force for grain growth. If, however, the matrix grains are free to grow simultaneously, the driving force for exaggerated growth will be diminished. Stability toward growth of the matrix grains may be caused by a) a strong single orientation texture (texture inhibition),&apos; b) a dispersed second phase,3"5 c) the thickness effect,&apos; or d) intergranular segregation.7"9 As exaggerated growth occurs when growth of the matrix grains has been slowed by the stabilizing processes mentioned above, there must be an additional factor acting to promote growth of a few of the grains to the point where they are enough larger than the matrix grains that boundary energy driving forces are sufficient to cause continued growth. For instance, at the annealing temperature, growth-inhibiting inclusions may slowly dissolve and coalesce. Eventually, a grain boundary becomes unlocked and migration occurs at the expense of neighboring grains. Or, an additional driving force may be supplied to some of the grains if the material is strained. Then, since some grains will be strained less than others, the difference in strain energy between adjacent grains may be sufficient to overcome boundary locking and allow growth of the grains with lower strain energies. In the present study, therefore, such factors as the presence or absence of dispersed phases, the nature of the exaggerated growth, and the effect of strain have been considered. EXPERIMENTAL PROCEDURE I) Material and Processing. Three types of low-carbon iron were used in this study; types A and B were commercial grades, each from a different supplier.* The precise details of the processing of

Jan 1, 1963

By D. W. White

The kinetics of isothermal transformation of ß-to-u uranium have been studied over a broad temperature range in alloys containing from 0.3 to 4.0 atomic pct Cr. Two modes of transformation are indicated by the existence of two C-curves in the TTT diagram. The upper temperature mode is regarded as a nucleation and growth mechanism, whose rate is controlled by diffusion of chromium in the ß phase matrix. The lower temperature mode is martensitic in nature. The M, temperature increases with decreasing chromium content, suggesting that the two transformation processes become synonymous in unalloyed uranium. URANIUM metal undergoes two allotropic transformations in the solid state. The a phase, orthorhombic in crystal structure,&apos; is stable from room temperature up to about 665°C. The ß phase, characterized by a complex tetragonal structure,&apos; prevails from 665" to about 770°C. The y phase is body-centered-cubic3 and is the stable modification from 770°C up to the melting point (about 1130"). In uranium of reasonable purity, neither of the two high temperature phases can be retained by quenching. However, the addition of certain alloying elements to uranium makes it possible to retain either the y-uranium phase or the ß-uranium phase at room temperature. Chromium alloyed in small amounts with uranium will permit retention of the ß-uranium phase in a metastable state at room temperature upon quenching from a ß-phase temperature.&apos; From available information&apos; on the equilibrium phase diagram for the U-Cr alloy system (Fig. I), it is to be expected that, however sluggish in its rate, the ß phase in such alloys should decompose eutectoidally to a phase and elemental chromium. It was the aim of this investigation to measure the rate and study the nature of this decomposition as a function of temperature and of chromium content. The investigation was reported in classified literature about five years ago and has recently been declassified for publication. In the meantime, there have appeared the papers of Holden,5 Mott and Haines,".&apos; and Butcher and Rowe8 ealing with the metallography and the crystallography of the ß-to-a transformation in U-Cr alloys. These investigators have confirmed several of the phenomenological observations that will be described in the present paper and have examined in considerable detail certain aspects of the transformation and its mechanism. Although all of these investigations have concerned themselves experimentally with U-Cr alloys for the most part, an important consequence has been a clearer understanding of the nature of the ß-to-a transformation in uranium metal itself. Experimental Procedure This investigation dealt with a series of uranium alloys varying in chromium content from 0.3 to 4.0 atomic pct (0.066 to 0.90 weight pct). On five of the alloys, rates of isothermal transformation from the ß to the a phase were measured over a wide temperature range, leading to the development of TTT (time-temperature-transformation) diagrams. Transformation rates were measured over certain narrow temperature ranges on additional alloys. The alloys were prepared by vacuum melting and casting, using zircon or magnesia crucibles and graphite molds. Electrolytic chromium was used as the alloying addition, and the uranium was Mallin-ckrodt biscuit metal that had been vacuum remelted and cropped to remove many of the nonmetallic impurities that had floated to the top of the ingot. The ingots, 3/4 or 1 in. diam, were reduced in size by swaging. Alloys containing less than about 2 atomic pct Cr were swaged at 250° to 275°C, with initial and intermediate anneals at 550°C after every 75 pct reduction in area. Alloys with higher amounts of chromium were swaged at 550" to 600°C, although at the smaller sizes some of them were reduced by the procedure used on the more dilute alloys. Before use as test specimens, the swaged rods were annealed at 700" to 720°C for several hours, followed by slow furnace-cooling. The purpose of the anneal was to achieve the maximum amount of solution of the available chromium into the ß phase, as well as to remove extensive preferred orientation. The isothermal transformation rates were measured dilatometrically, using a quenching dilatometer and an experimental technique similar to those employed by Davenport and Bain in their original work on the transformation kinetics of austenite in

Jan 1, 1956

By L. D. Lash, J. R. Ross

Discovery of scandium in the Vitro solvent extraction plant for uranium led to commercial recovery of the byproduct. Micro amounts of scandium were extracted with uranium by dodecyl phosphoric acid, but failed to follow ura-niuminto the hydrochloric acid strip solution and were eventually concentrated in the organic extractant. A fluoride strip system was developed to recover scandium from the solvent in concentrated form. High purity scandium oxide was then prepared in multi-pound lots by chemical separation techniques. The plant recovery operation, final product purification, and analytical procedures are described. Scandium is a pseudo-rare earth which is truly rare and expensive. It has special properties which may make it desirable even at the present price of $2750 per lb. Recently the price was lowered from $5000 per Ib which had prevailed since 1952, and it is anticipated that usage will be stimulated because of the lowered price. This metallic element is distributed widely in trace amounts in the rocks of the earth&apos;s crust. In addition to micro-amounts found in most uranium ores, concentrations of 50 to 100 ppm have been found in Colorado ferberite ore, lateritic nickel ore, heavy sandstone from Utah, Wyoming, and New Mexico, and various zircon sands and monazites from the western part of the U. S. Scandium has been found as an essential constituent of very few minerals, the most important being thortveitite, a scandium silicate. At the present time, this mineral commands a price more than twice that of gold. Chemically, scandium is in group 3A of the periodic table. It is closely associated with yttrium and the rare earths which it strongly resembles in its reactions. It has a valence of three and will form an insoluble hydroxide, fluoride, or oxalate under proper conditions, similar to the rare earths. Eight years before its discovery, scandium was predicted by Mendeleef who ascribed his eka-boron with properties nearly identical to the actual properties of scandium. Its position as the element with Atomic No. 21 and Atomic Weight 44.96 places it between calcium and titanium in Period 4 of the chart. The successful commercial application of scandium must depend on unique properties to justify use of this high cost substance. Greater consumption would allow additional price reductions, but scan- dium will remain a relatively high-priced commodity because of its inherent scarcity. Research reportedly has been oriented toward use of scandium as an agent to achieve high-temperature, low-density alloys with magnesium and tantalum.&apos; Also, the U.S. Air Force sponsored a project for production of research amounts of pure scandium metal.&apos; The oxide has been used experimentally in electronics, ceramics, and metallurgy. The various aspects of scandium are well covered in recent publications.s-5 CONCENTRATE RECOVERY Small amounts of scandium exist in uranium ores and are dissolved during an acid leach yielding up to 0.001 gpl Sc2O9. When Vitro converted their uranium plant from phosphate precipitation to solvent extraction: scandium was found to follow the uranium into the dodecyl phosphoric acid solvent (DDPA). However, scandium did not strip with uranium from the DDPA in hydrochloric acid, but remained in the solvent. Therefore, a concentration of scandium built up in the organic phase. Residues from the solvent were spectrographed by the U.S. Bureau of Mines and found to contain scandium. As a result of this discovery, provisions were made in the plant for recovery of scandium-bearing concentrates. Solvent extraction of uranium was added to a conventional acid leach process in a typical installation? The ore was crushed and ground, and then leached with dilute sulfuric acid. Addition of an oxidant such as sodium chlorate insured conversion of uranium minerals to a soluble form. At this point, the slurry was chemically reduced by a sulfide, such as sodium hydrosulfide, to remove substances such as ferric iron and molybdenum which were partially extracted by the solvent. The solids-liquid separation was accomplished by a four-stage counter cur rent decantation (CCD) thickener circuit. The uranium was extracted from pregnant liquor with 0.1M DDPA in kerosene and stripped with ION

Jan 1, 1961

By L. A. Panek

During the past three years, USBM has developed an apparatus and technique for direct measurement of existing pressure and change of pressure in mine rock. This relatively simple and inexpensive monitor is reliable for months after being installed. It is used to determine shift of ground pressure created by different sequences of mining, to ascertain the cause of rock failures, and to evaluate the need for artificial support. The technique has been employed to measure pressures in limestone, greywacke, concrete, diabase, and soft iron ore. When rock is subjected to a load it is deformed. Ordinarily this is observed in a mine as the displacement of one point with respect to another—the deflection of the roof, which may be observed as a convergence between roof and floor; or the extrusion of material from the rib, which may be observed as a decrease of the distance between the rib and the post of a timber set. The effect of excessive pressure may be a rockburst if the rock is strong, or it may be squeezing ground if the rock is soft. Some desirable effects of high stress (high in relation to strength) are the caving of roof in a longwall mining operation, the caving of ore in block caving, and the decrease in mechanical energy required to break down the mineral seam in a retreating pillar-robbing operation. In any case, whether the observable effect of rock load is desirable or undesirable, it is a displacement, and depends on the following four factors: 1) The structure—the size and shape of openings, pillars, and linings, the geologic bedding and jointing. 2) The mechanical properties of the rock—prin-cipally the strength, modulus of elasticity, and flow characteristics. 3) The load or applied stress—primary sources are the weight of superincumbent rock, which increases with depth, and unrelieved tectonic stresses; secondary sources are redistributed pressures caused by other nearby openings, especially large mined out zones (rock pressure depends partly on the rock structure created by mining). 4) Duration of load, related to the length of time the opening is exposed. CONTROL OF ROCK DISPLACEMENT Rock displacement can be controlled by control of these four factors. Consider now the means of exercising such control over these factors. Control of the structural features is obviously possible to a great extent, as such control is exercised largely by choosing the method of mining and the methods of natural and artificial support. Rock properties vary, even within a particular mine, but they are controllable only in the limited sense that control may be exercised by choosing the beds or zones to be mined so that rocks with undesirable properties will not occupy critical positions within the rock structure created by mining. Rock pressure is the most complex of the four factors through which ground control can be achieved because it is invisible, difficult to measure, and poorly understood. Rock pressure is controllable only to the extent that control is exercised on the rock structure created by mining. Considering openings within a particular mine, time of exposure varies, and is readily controllable because it is easily measured and easily understood — the longer an opening stands, the greater the likelihood of failure or excessive convergence. Control is exercised by choice of an appropriate sequence of driving openings of different classes, such as haul-ageways and rooms, which are required to remain well supported for different lengths of time under different conditions. Again, control is exercised through the method of mining. All controllable factors can be controlled by proper design of the mining method. The orientation and relative positions of the mine workings and the sequence of their excavation are likely to be much more important to ground control than is the design of artificial support. This implies that the major decisions in regard to ground control are made, knowingly or not, at the time the mining method is chosen. WHY MEASURE ROCK PRESSURE In addition to restrictions on the several factors, control implies the measurement of these factors in some sense, whether only qualitatively by visual observation, or by actual quantitative determination with a measuring instrument. Rock pressure is the most difficult of these factors to measure, largely because of the interaction between the measuring device and the rock. Nevertheless, the quantitative

Jan 1, 1961

By M. Hoch

Equations are derived from statistical considerations to represent the activities of each component of an interstitial solution, and of a compound with a wide homogeneity range as a function of composition and temperature, based on the interaction energies between the various components, Eij. The equations are checked on the binary systems Fe-C, Ta-H, and Y-H, the ternary systems Ti-O-H, liquid Fe-C-0, and the compounds TiO, MnO, COO, and YH,. In all cases the present model represents the experimental data well. THE aim of this paper is to derive from statistical considerations the thermodynamic behavior of non-substitutional solid solutions. "Nonsubstitutional solid solution" means either an interstitial solid solution (carbon in iron, oxygen and hydrogen in hexagonal and bcc titanium, and so forth) or deviation from stoichiornetry in compounds (introduction of vacancies—removal of atoms in one or both lattice sites of compounds FeO, MnO, TiO, NbO, YH2). wagnerl and Fowler and Guggenheim considered the theory of compounds with small deviation from stoichiometry; Anderson includes larger deviations from stoichiometry, the defect being present in one component only, as vacancy and interstitial. Rees considers only vacancies in one of the components and introduces various kinds of sites for the component where the defect occurs; the various sites interact with different energies, thus giving isotherms with two or more plateaus. Both Rees and Anderson are mainly occupied in determining the limits of two-phase regions, and the defect interaction energy is determined from the critical point. Darken and Gurry5 gave a brief treatment of carbon solution in iron; Speiser and spretnak calculated the configurational entropy for binary interstitial solid solutions by assuming that each interstitial atom in the solution excludes a certain number of neighboring interstitial sites from occupancy. Use will be made of this concept later. Hoch et al treated transition metal oxides of the NaCl-type structure, and also oxygen solution in titanium.&apos; The main aim was to determine the behavior of the activity of one of the components as a function of the composition in the single-phase region. In the present paper, the various interaction energies are discussed in detail and the similarity between interstitial solid solutions and deviation from stoichiometry in ionic compounds is shown. Both types of systems have in common that at least on one kind of lattice site only one kind of atom occurs; this gives a fixed frame to the system, permitting a much easier statistical treatment than for the substitu-tional solid solutions. (The theory is also applied to ternary systems.) The difference between an interstitial solution and deviation from stoichiometry can be explained as follows. In an interstitial solution in the pure or standard state the host atom or host structure is present alone and all the interstitial sites which are going to be filled when the interstitial atom is introduced are empty. The interstitial solution is now created by introducing atoms into this empty lattice. In the deviation from stoichiometry, both kinds of lattice sites are already occupied in a special fashion (all lattice sites occupied, or the same fraction of lattice sites empty, or one kind completely filled, the other only two-thirds). Deviation from stoichiometry removes atoms from lattice sites, adds them, or removes atoms from one kind of lattice site and introduces them on the other lattice site. Though both cases (interstitial solution and deviation from stoichiometry) lead almost to the same equations, they are treated separately. The treatment given below corresponds to the "regular solution"10 treatment of substitutional solid solutions. Speiser and spretnak&apos;s6 treatment is similar to the athermal solution in the substitutional use. a) INTERSTITIAL SOLID SOLUTIONS Theory. It will be assumed that there are N lat-tice sites occupied by the host atom (denoted by 1). Corresponding to those N lattice sites there are N octahedral and EN tetrahedral interstitial sites. If only one kind of interstitial atom is added, this in-

Jan 1, 1964

By Y. C. Kim, C. B. Manula

This paper is concerned with the details of the derivation of an operations research model, specifically linear programming, to solve production scheduling problems. While some results are presented for an actual study, the calculation of cases of a more general nature have not yet been completed. Production managers from those segments of the mining industry that experience a seasonal or highly variable sales demand find it rather difficult to develop overall producing plans for their organizations. In an attempt to solve this technical problem, demands are usually met by keeping production corresponding exactly to sales. This results in a fluctuating production schedule which is costly to maintain because of overtime premiums in periods of high requirements and because of costs associated with an idle mine plant during slack periods. An alternate solution may be to produce part of the desired amount and make up any deficiencies by using overproduction in previous time periods. This tends to smooth the production pattern through the use of a stockpile. However, because of associated storage costs, the solution may again be undesirable if it yields comparatively large surpluses. In general, this type of scheduling problem has an infinite number of solutions which satisfy the requirements. These are largely dependent on the extent to which an operation is geared to changes in production and on the size of its stockpiling facility. The determination of an efficient schedule is implied, therefore, as one lying between two extreme solutions, i.e., one that minimizes surpluses and one that minimizes output fluctuations. These conflicting objectives result in an economic balance problem between the costs of carrying surpluses forward from slack periods versus the cost of high production levels during peak demands. Various methods of operations research have been developed to handle problems whose genesis is explained above. It is very seldom, however, that these quantitative means are used in practice by the mining industry. Those who are familiar with mining operations know that most managers have not progressed satisfactorily in this area. Production planning systems which most mines employ today are often no more than rough records of management&apos;s mental planning. For small mines these means are normally sufficient; but as operations grow larger and become more complex, this type of planning ability is no longer adequate. Managers may find themselves losing control of cost relationships, taking longer to outline production sequences, and becoming forgetful of certain resource availabilities. ORIGIN AND SCOPE OF A SCHEDULING PROBLEM The more fundamental aspects of the production scheduling problem can be brought into focus by demonstrating how it exists in a bituminous coal mine* located in southwestern Pennsylvania. This mine, operating in the Pittsburgh seam, uses a definite room-and-pillar block system of mining, which is planned and carried out with only slight variations to meet local conditions. The coal seam, which is firm and varying in thickness from 8 to 9 ft with the bottom 6% ft being extracted, is under 500 ft of cover and opened by a shaft. The bulk of the coal (60%) is obtained from the pillaring activity with the mains and sections, which are considered primarily as development activities, contributing the balance of 12% and 28%, respectively. All coal is won by a ripper-type continuous miner in conjunction with shuttle-cars directly behind a loading machine. Track haulage is employed to move coal from these machine centers to the shaft bottom. The coal, thus mined, is shipped to one destination as part of a mixture of coals to be used in the making of steel. A material flow diagram of this distribution scheme is illustrated in Fig. 1. PROBLEM STATEMENT From the above types of shipments and mining limitations, the basic problem is to determine an economic means of producing and stockpiling a single coal product produced in three different machine centers (main, section, and pillar). Fig. 2 shows total demand for coal as a function of time. Because of the extremely high peak demands, slack period production must be stored and then distributed

Jan 1, 1969

By O. R. Morris, G. L. Hawkes

A galvanic cell, using as electrolyte a fused salt solution of calcium carbide and as electrodes carbon and a Fe-C alloy of known composition, has been set up to study the thermodynamics of Fe-C alloys in the temperature rmzge 800" to 1000°C. Time independence and reproducibility of the cell electromotive force were taken as evidence of the reversible behavior of the cell. Carbon was believed to be present in the electrolyte as the so-called acetylide ion, C;-. The plots of the cell electromotive force us temperature for a specific alloy composition were straight lines within the limits of experimental error. The average Partial molar enthalpy of carbon in iron relative to pure carbon was found to be +10,610 i 93 cal per g-atom C. Thermodynamic analysis of the data has led to the following equation for the carbon activity, ac, based upon pure carbon as the standard state: In ac = In Zc + 10,560/RT + (10.02 + 77O/T)ZC - 2.350 where ZC is the lattice ratio [nC/(nF, - nc )] and T is the absolute temperature. This equalion gives carbon activity values generally slightly lower than those from gas equilibration studies reported in the literature. METAL LOGRAPHIC examination of a polished cross section of the steel anode used in the electrolysis studies of fused salt solutions of calcium carbide by Morris and Harry revealed extensive carburization of the steel by the electrodeposited carbon. This carburization was reflected in the variability, with time, of the applied potential to the electrolysis cell, necessary to maintain a constant current density at the electrodes. This observation suggested the setting up of a galvanic cell of the "alloy concentration" type to study the thermodynamics of some metal-carbon alloys. Cells of this general type have been widely used for the study of alloy systems.2 In view of the availability of published data in respect of the austenite phase of the Fe-C system, it was decided to carry out measurements upon these alloys before proceeding to studies of less well documented systems. The galvanic cell may be written: where [C] is carbon dissolved in iron. The electrolyte was a fused salt solution of calcium carbide, containing some 5 to 10 mol pct of carbide. The cell reaction is believed to be: C(s)-[CI [I1 Carbon forms an interstitial solid solution in iron, with the atoms located in the octahedral interstices. In the fcc crystal structure of austenite there is one octahedral interstice per iron atom. Thus, the lattice ratio, ZC, shown by Gurney3 to be the fundamental concentration parameter in the context of interstitial solutions, is given by: where nc and nFe are the number of carbon and iron atoms, respectively. chipman4 has recently shown empirically the advantages of using this concentration parameter instead of the more usual atom ratio or atom fraction. The cell electromotive force, E, assuming reversible behavior, is related to the carbon potential or the partial molar free energy of carbon in the solid solution relative to pure carbon at the same temperature and pressure, GP at the composition ZC, by the equation: where z is the carbide ion valency and F is the Faraday constant. An activity of carbon, ac, in the solution relative to the value of unity assigned to pure carbon, and an activity coefficient, qC , are defined such that: where R is the gas constant and T the absolute temperature. GF is further related to the relative partial molar enthalpy Hm, and the temperature coefficient of the cell electromotive force, (aE/aT)Zc, by the equations: Measurement of the cell electromotive force thus enables calculation of the relative partial molar thermodynamic properties of carbon in iron, if z is known. At E = 0, the solid solution is in equilibrium with pure carbon. More convenient for many purposes is the standard state based upon the infinitely dilute solution, Henry&apos;s law. The relationship between the activity coefficient of carbon based upon this standard state, and that based upon the pure carbon standard state, qC , may be obtained by considering the free energy of transfer of carbon from the latter standard state to the former. The relationship is: where +:H is the activity coefficient of carbon in the hypothetical standard state based on a reference of

Jan 1, 1969