Search Documents

By Charles Wert

THE diffusion and precipitation of carbon and nitrogen in a iron have previously been investigated using the internal friction as a measuring tool.' Most of this work has been done on rather pure iron; no effect was observed which would indicate that either of these phenomena is affected by the rather small amounts of impurity found in these samples of iron. Fastz observed, however, that both the diffusion rate and the aging properties of nitrogen in iron were sensibly changed by the addition of Vz pet Mn. The diffusion rate at a given temperature is reduced and the nucleation of nitrides is apparently changed somewhat. He observed no such changes for carbon in this alloy. Later Dijkstra and Sladek" extended these observations on nitrogen to other alloys of iron. They found that metals other than manganese also influence the behavior of nitrogen in iron; chromium, molybdenum and especially vanadium affect the diffusion and precipitation of nitrogen even more than manganese does. Their results have been verified in all essential details by this author, who finds in addition that small additions of nickel have about the same effect on the diffusion of nitrogen as the same amount of manganese. The present work was undertaken to study the effect on carbon in iron of these alloying elements. The alloys used had two sources. The material used as a "standard" (designated Fe in this paper) in the measurements was some iron supplied by J. K. Stanley, of Westinghouse Electric Corp., who reported 0.01 pct 0, as the only major impurity. He also made up an alloy of 0.26 pct Ni and one of 0.9 pct Mo using this same iron as a base. They were supplied by him in 2 lb billets, which were sawed into rods and cold formed into 0.030 in. wires for measurement. The alloys of chromium, manganese, and vanadium were prepared by the metallurgy section of the Institute for the Study of Metals, University of Chicago, by adding these metals in turn to vacuum melts of National Research Corp. iron. The small castings prepared in this way were also cold formed into 0.030 in. wires. After these wires had been prepared they were decarburized for 30 min at 730°C in wet Hz. After this treatment, no trace of carbon (as measured by internal friction) could be found. All specimens were then carburized for about 15 min at 710°C and water quenched. By this treatment the internal friction at 40°C was raised to a Q-' ~ 0.015. The diffusion of carbon in these alloys was studied by observing the shape and position of the internal friction peak at 0.9 cycles per sec. These measurements were made using a torsional pendulum in a manner described earlier.' The data are plotted in Fig. 1. It is seen that there is no apparent difference in internal friction between the various alloys. This is in marked distinction to the broadening and shift-

Jan 1, 1953

By Leo H. Glanville

Until 1934, natural ventilation was depended upon in the mine of the Climax Molybdenum Co. at Climax, Colorado. In that year a 7-ft. axial-flow, low-pressure fan was installed as an exhausting unit. In 1936, three more fans of the same kind were installed, all as exhausting units, with a total capacity of 115 000 cu, ft. per min., and since then fans and sprays have been added as required. Atmospheric Conditions Adverse atmospheric conditions at this elevation of 11,500 ft. account in part for difficulty in maintaining adequate ventilation throughout the mine. Barometric pressures range from 18.99 to 20.01 in. of mercury; the norma1 average being 19.70 in. Air weight is 0.051 lb. per cu. ft., and humidity is low—about a 30 per cent yearly average. This makes the use of mechanical humidity aids mandatory the Year around to prevent excessive dryness of the mine workings and the resultant dust hazard. The yearly temperature range is from minus 24" to 75°F.; typically, in February 1942 the mean low was minus 3.25°F. and the mean high, 21.3°F. In August the mean low was 34.8°F.; the mean high, 64.26°F. Even during the summer month air filtration through the openings of the cave area is 32°F., owing to accumulation of snow in the glory hole and in Part to glacial ice, which, combined with a rock temperature of 39°F. on the upper levels (elevation 11,945 ft.) and 42°F. on the main haulage level (elevation 11,470 ft.], makes it difficult to maintain a comfortable working temperature. The one advantage in ventilation of mine workings at the altitude of the Climax mine is that the power required to circulate a given air volume is 32 per cent less than would be required at sea level. Problems since 1936 the mine management has studied intensively plans for providing adequate ventilation for the entire mine for its expected life. As the ore breaks into large pieces, much secondary blasting is necessary, therefore there is a considerable amount of smoke, gas and dust, which requires circulation of a large amount of air to remove the contamination, It is undesirable to use haulage drifts and manways as air passages because some would be passageways for contaminated air also, and there would be undesirable high velocities in some drifts. High velocities and large volumes of subfreezing air dry out the passageways through which they pass, and thus increase the amount of dust. Regulating doors in haulage drifts are difficult of upkeep and interfere with production. It was decided as a general principle to distribute fresh air to each working place at low velocities and low pressures and to remove contaminated air as soon as possible with a minimum of travel through working places.

Jan 1, 1943

By Leo H. Glanville

Until 1934, natural ventilation was depended upon in the mine of the Climax Molybdenum Co. at Climax, Colorado. In that year a 7-ft. axial-flow, low-pressure fan was installed as an exhausting unit. In 1936, three more fans of the same kind were installed, all as exhausting units, with a total capacity of 115 000 cu, ft. per min., and since then fans and sprays have been added as required. Atmospheric Conditions Adverse atmospheric conditions at this elevation of 11,500 ft. account in part for difficulty in maintaining adequate ventilation throughout the mine. Barometric pressures range from 18.99 to 20.01 in. of mercury; the norma1 average being 19.70 in. Air weight is 0.051 lb. per cu. ft., and humidity is low—about a 30 per cent yearly average. This makes the use of mechanical humidity aids mandatory the Year around to prevent excessive dryness of the mine workings and the resultant dust hazard. The yearly temperature range is from minus 24" to 75°F.; typically, in February 1942 the mean low was minus 3.25°F. and the mean high, 21.3°F. In August the mean low was 34.8°F.; the mean high, 64.26°F. Even during the summer month air filtration through the openings of the cave area is 32°F., owing to accumulation of snow in the glory hole and in Part to glacial ice, which, combined with a rock temperature of 39°F. on the upper levels (elevation 11,945 ft.) and 42°F. on the main haulage level (elevation 11,470 ft.], makes it difficult to maintain a comfortable working temperature. The one advantage in ventilation of mine workings at the altitude of the Climax mine is that the power required to circulate a given air volume is 32 per cent less than would be required at sea level. Problems since 1936 the mine management has studied intensively plans for providing adequate ventilation for the entire mine for its expected life. As the ore breaks into large pieces, much secondary blasting is necessary, therefore there is a considerable amount of smoke, gas and dust, which requires circulation of a large amount of air to remove the contamination, It is undesirable to use haulage drifts and manways as air passages because some would be passageways for contaminated air also, and there would be undesirable high velocities in some drifts. High velocities and large volumes of subfreezing air dry out the passageways through which they pass, and thus increase the amount of dust. Regulating doors in haulage drifts are difficult of upkeep and interfere with production. It was decided as a general principle to distribute fresh air to each working place at low velocities and low pressures and to remove contaminated air as soon as possible with a minimum of travel through working places.

Jan 1, 1943

By Alexander B. Morris

Studies such as the investigations into the solubility of gases in crude oil under various conditions, which have been carried on during the past three or four years, are very interesting from an academic point of view, but this consideration alone is hardly sufficient to warrant the large contributions from the industry necessary to maintain them. Some definite benefit to the industry as a whole should be forthcoming. The purpose of this paper is to direct the attention of company engineers, and company executives, to some of the ways in which the information gained from these studies can be made directly profitable. This work has two principal economic aspects. One affects the investment budget, and through it the financial requirements of the companies. The other affects operations, and through this course is reflected in current earnings. It will be shown that, as a direct result of the investigations into gas solubility, undertaken in the recent past by various investigators, it is now possible: 1. To determine more accurately the amount of reservoir oil originally present. 2. To obtain closer control on operating conditions, to effect more economical recovery. 3. To predict earlier and more dependably when and how much surface lifting equipment will be needed. 4. To reduce, or entirely avoid the very large investment in gasoline recovery equipment now frequently found necessary. 5. To control the gravity of the pipe-line oil so as to secure the greatest possible revenue from the products of the well. 6. To effect the recovery of a large amount of gasoline now wasted while the practicability of a gasoline recovery system is being decided. 7. To plan operations, by comparison with the history of old properties operated without this new information, so as to avoid the mistakes of ignorance made in the past. These points will be discussed in the following pages, though not necessarily in the order stated. There is so much overlapping of the points themselves, and of the data from which they have been drawn as conclusions, that to treat them in any particular order would require

Jan 1, 1935

By Johann F. Kerl

Autogenous batch grinding tests were performed in laboratory-scale tumbling mills with magnetite, limestone, and sandstone pebbles. The influence of pebble size, feed size, mill speed and loading, and grinding time on the fineness of grinding was investigated. Comparisons were made with the results from ball mill grinding experiments.

Jan 1, 1972

By Robert Archer

IT is now well known that the structure of aluminum-silicon alloys can be refined in a rather remarkable manner, with consequent improvement of physical properties, by certain treatments applied to the molten metal shortly before casting. The differences between the treated and the untreated alloys are so marked that special terms are used to distinguish them, the untreated alloys being referred to as "normal" and the treated alloys as "modified." The first practical method of accomplishing this result was that of A. Pacz,1 which consists in treating the molten metal with a, salt flux of which the, active ingredient is sodium fluoride. The result can also be brought about, and in a more economical manner, by the addition of small quantities of metallic sodium (or potassium) to the molten alloy shortly before casting.2 The action of the Pacz flux evidently consists essentially in the production of free sodium by the reaction of sodium fluoride with aluminum. The changing of a normal alloy to a modified alloy is referred to as "modification' and any process for accomplishing this result is a "modifying" process. Modified aluminum-silicon alloys were introduced several years ago, and it has been demonstrated both in the laboratory and in commercial practice that it is no simple matter to produce castings having the maximum or nearly the maximum properties which under favorable circumstances can be obtained. The alloys are rather sensitive to small changes in chemical composition, and the modifying process must be carried out in a very particular manner to obtain the best results. Extensive experimental work has been carried out in the laboratories of the Aluminum Company of America with the object of determining the conditions that must be observed to make these alloys of the greatest possible

Jan 2, 1926

By David White

ATTENTION has been given to the sources and supply of the raw vegetal matter and. the conditions of its submission to the process of sedimentation. An original and most valuable review has been made of the more important or significant chemical compounds originally contained in the organic debris, and of the biochemical changes-undergone by the latter during deposition. Consideration also has been given to the factors controlling the selective biochemical decomposition, in whole or in part, of :this debris, and the deposition, as, sediments, of the undecomposed plant structures and compounds, together with more or less of the so-called "ulmic," or "humic," organic decomposition products in colloidal solution.1 BIOCHEMICAL CHANGES END IN PEAT FORMATION The biochemical process terminates in the peat stage of coal formation, and with the cessation of this process organic sedimentation is completed. All subsequent changes result from geological causes and conditions. The deposits are in the form of peats of different types, organic muds, oozes, etc. They are essentially uncompressed and are wholly unconsolidated, and their water content is great, amounting to over 85 per cent. near the surface of the deposit. Many of the chemical compounds remain as in the once living organisms; others are biochemically broken down and new ones formed.

Jan 2, 1925

By M. G. Corson

INFORMATION regarding the use of manganese alloys has hitherto been incomplete and available only from widely scattered sources. This paper attempts a systematic description of properties and uses of alloys other than manganese bronze, manganin and duralumin, which are probably the only non-ferrous alloys associated with manganese in the minds of most metallurgists.1 PROPERTIES OF MANGANESE Manganese can react either acid or basic; it is hard to obtain in the pure state; it has two different crystalline lattice structures, both of the cubic system, one stable above 850° C. and the other below 650° C., both coexisting in the intermediate range. Although the commercial product is hard and brittle, the pure metal seems to be ductile. In fact Zhemchuzhny, in Russia, was able to obtain ductile manganese and draw it to fine wires by the simple expedient of adding about 3 per cent. copper to the alumino-thermic product. Copper most probably brings the sili-cides, aluminides, nitrides and carbides present in the commercial product into a much less harmful form of distribution. One industrial use that can be foreseen for wrought manganese articles is as anodes for electrolytic processes in sulfate and nitrate solutions, particularly with high voltages. A practically insoluble skin of manganese peroxide is likely to form in such cases and an insoluble and strong anode material will be available.

Jan 5, 1927

By H. K. Birnbaum

The termination of a twin lamella in the interior of a crystal requires accommodation of the strains at the tip of the twin which result from coherency of the twin and matrix. In zinc and magnesium crystals,

Jan 1, 1960

By J. W. Leonard, J. C. Anderson, C. T. Holland

PREPARATION CONTROL IN UNDERGROUND MINING Selective Mining According to district Depending upon the particular geographic loca- tion or seam characteristics, modern raw coal preparation practices can be used to obtain improved product quality and uniformity. Nevertheless, certain coal markets may require only marginal quality while others may require very high quality, and these objectives may be sought by commencing the preparation of coal underground at the "working face." Under- ground preparation involves choosing those portions of the seam which can be cleaned to satisfy predetermined market requirements involving ( 1 ) maintenance of uniformity in chemical quality, (2) elimination of removable impurities, (3) control of sizes and size ratios, and (4) control of moisture. The methods employed to attain these objectives vary widely with the (1 ) seam under development, (2) mining equipment available, and (3) changing trends in the consuming markets. When a mining property is opened and development progresses from one section to another, the (1) petrography of the coal in the seam does not remain uniform, (2) character of roof and floor are subject to change, and (3) character and prevalence of mineral impurities are subject to considerable variation. The quality of coal shipped to market from any mine depends upon intelligent foresight, planning, execution, and supervision. Mining becomes a highly technical art. The quality of coal as determined by chemical and petrographic analysis is without question one of the most important considerations in the development and life of any coal-mining property. Variations in such proper- ties as volatile matter, ash, sulfur, Btu content, and petrography are of considerable interest, and to a limited extent so are such properties as phosphorous content, free swelling index, plasticity, hardness, pressure formation during coking, and ash composition. The maximum and minimum specifications of these characteristics as established by competitive market conditions place definite limits on the marketability of a coal.

Jan 1, 1979

Escalating energy costs and tough environmental standards were two major factors affecting the minerals processing area in 1978 For the most part, new startups and research and development initiatives were directed toward improving process dynamics, investigating alternative processing strategy, and lowering unit costs. In the flotation area, the trend to larger machines continued. Scientific investigation of the modeling and process control of flotation was apparent, as was the research and development of new flotation reagents.

Jan 5, 1979

By Donald A. Dahlstrom

In 1961 it became increasingly more evident that significant technological changes must be made in minerals beneficiation. The status quo in technology in today's competitive markets will not be tolerated. Higher productivity, greater recoveries and newer and better products must be sought and incorporated with lower operating costs. In other words, "when you build a new mill, don't build an old mill." Recommended reading for proof of the vital necessity of new methods and techniques is in the September 1961 issue of MINING ENGINEERING. The article by one of MBD's cherished and true veterans, E. H. Rose, is entitled "Iron Ore: The BIG Picture". Because of new beneficiation methods for iron ores, nearly 47 million tons of plus 60% iron concentrates will be produced and another 40.1 million tons of capacity will be under construction or committed. Thus in a relatively short period, 87 million tons of this high-grade iron concentrate with record low silica will be available. As Mr. Rose also points out, "in gross tons, without allowance for better grade, this is the equivalent of almost exactly two-thirds of all iron ore used for all purposes in the U.S. and Canada in the peak years of 1953 or 1957." Needless to say, improved mineral beneficiation methods have had far more reaching effects than just the production of higher grade iron concentrate.

Jan 2, 1962

Jan 1, 1916

By Samuel Hoyt

THE writer has long been interested in seeking an explanation of the upper heat effect in the copper-tin alloys over the a + ß range, first described in 1913. These notes are offered, not at all as the final explanation of this heat effect, but rather to indicate certain progress which has been made toward establishing what happens over this temperature interval. While working on the thermal analysis of the copper-rich kalchoids (copper-tin-zinc alloys), it was noted that those alloys containing major portions of tin and minor portions of zinc exhibited two marked heat effects, one at about 520° C. and the other at about 600° C., instead of the single effect which is generally observed in either of the two binary series. This matter was discussed with Dr. Guertler, who suggested that a heat effect at about 600° C. in the pure copper-tin alloys might be expected. This led to a more searching examination of the thermal critical points in the pure copper-tin alloys, with the result that a marked, although somewhat weak, heat effect was located at about 600°. Somewhat later, this upper heat effect was discussed with Dr. Burgess, and it was requested that the Bureau of Standards make heating and cooling curves of one of these alloys for the purpose of removing any possible doubt as to the actual presence of the heat effect. Results obtained by the Bureau are given in Plate I. In an earlier paper1 differential curves were published showing that the heat effect occurred at constant temperature over the a + ß range and increased in magnitude with the amount of a up to a point somewhat above 20 per cent. tin. No heat effect was noticed at this temperature in the eutectoid alloy. The existence of this heat effect seems to require a modification of the present copper-tin diagram in the a + ß field, and it has been the object of the work here presented to secure the evidence upon which such a change should be based.

Jan 12, 1918

By Frank Rieber

THE discovery that strongly magnetic bodies localized near the surface of the earth could be detected by the distortion which they produced in the resultant magnetic field marked the beginning of magnetic surveying methods. From an original ability to detect bodies of magnetic iron ore and the like when located very close to the, surface, these methods have been extended until today they promise to give much information with regard to the structure of such slightly magnetic material as sedimentary rock containing only a very small proportion of iron.1 The recent extensions have been made possible through the development of more delicate instruments, and of methods for their use. From the original compass and dip needle, the design of apparatus has progressed until equipment Is typified by magnetic balances capable of measuring the components of the earth's field to an extremely high degree of accuracy. It seems unlikely that the limit of such instrumental development has been reached. Just as the change from compass and dip needle has enabled the location of relatively minor changes in magnetic materials, so additional developments in the direction of increased sensitivity, as well as in greater dependability and constancy of operation, should reveal positively many slight changes which either escape notice in the present surveys or are so small that they cannot with certainty be separated from uncontrollable errors due to inconstant operation of the equipment. The ability to read smaller and smaller variations does not mean, of course, that deductions as to the causes of these variations will be made as accurately and definitely as -is possible with the more pronounced anomalies.

Jan 1, 1928

By R. M. Howe, J. Spotts McDowell

Preparation and Use.—Magnesite is an important refractory in open-hearth, heating, and electric furnaces for steel-making and in many of those employed in the metallurgy of copper and lead. It is sold in the form of brick, finely ground "furnace magnesite" for bricklaying, and dead-burned grains for making and repairing furnace bottoms. The latter are a mixture of granules varying in size from pieces of about 5/8 in. (1.6 cm.) diameter to very fine but sandy particles. Dead-burned magnesite results from calcining the crude or lightly burned mineral at a temperaturc that will not merely drive off practically all the CO2, but will also cause sintering of the particles. During this process the pieces shrink considerably and become hard, dense, and inert to atmospheric moisture and CO2; under-burned material, on the other hand, will hydrate on exposure to the air. A small percentage of ferric oxide seems to be necessary for the production of a satisfactory sinter; from 4.5 to 8 per cent. in the dead-burned grains is considered the most desirable amount. Dolomite has been little used for brickmaking in the United States, but it is prepared for use in the granular condition calcined or "double-burned" and is the principal ingredient of several materials offered for sale under various trade names for refractory purposes. Dolomitic refractories are almost wholly confined to the open-hearth and electric furnaces, where they are used for fettling and as substitutes for magnesite. Much more magnesite and dolomite are used for basic open-hearth steel-making than for all other refractory purposes. The hearth of the furnace is usually built up of magnesite brick and dead-burned grain magnesite so laid that the brick base is protected by a working bottom of the granular material. The latter is sintered into place in layers 1/2 to 1 in: (1.25 to 2.5 cm.) thick to a total depth of 12 to 18 in. (30 to 45 cm.) at the center of the furnace. After each heat, burned dolomite is thrown against the banks as high as it will stick, and all holes in the bottom are Glled. At most plants such holes, at the end of each week, are also carefully filled with dead-burned grain magnesite. For temporary

Jan 1, 1920

By Kenneth R. Hancock

Iron oxides are unique in that they are the only significant colored mineral found in a natural state suitable for use as a pigment after being pulverized to pigmentary size. The current world production of iron oxide pigments is estimated by the author to be between 499 and 590 kt (550,000 and 650,000 st) based on 1979 data. The fact that highly colored natural deposits of iron ore are found throughout the world accounts for its use in prehistoric man's artistic cave paintings. These early artists did not realize that they had established man's first paint test fence which now has some 20,000 years of exposure. In addition to abundance, constituting about 7 % of the earth's crust, iron oxides have the advantages of low cost, permanency, and are not toxic. Through the centuries, succeeding civilizations have utilized iron oxides as a major source for decoration and protection when coloring was desired. In the last century the chemical industry has improved on nature by developing a complete range of synthetic iron oxide pigments which surpass the pigments produced from natural iron ores in uniformity, color quality, and chemical purity. In the United States alone, the combined production of natural and synthetic iron oxides produced sales of over $28,000,000 in 1970 (Stipp, 1970) and increasing to $97 million by 1980 (Spinrad, 1980). Nomenclature With the increasing importance of the synthetic iron oxides it is necessary to make a distinction between the natural or mineral pigments and the synthetic pigments. Natural pigments are those products which are derived from selected ores and should not be confused with iron ores mined for steel production. Iron ores that are mined for steel must be capable of being mined and reduced to iron on a commercial basis. These ores are selected on the basis of iron content and processing economics. It is therefore unusual when iron ores for steel production are suitable for use as mineral pigments. Natural pigment ore sources are selected for their special physical-chemical properties and can command a premium price. Synthetic pigments, and in this instance iron oxides, are those pigments produced from basic chemicals. Through chemical synthesis pigmentary sized particles are produced as opposed to comminution, the major procedure common to all natural iron oxide pigments. Classification An important characteristic of a pigment is its color and, therefore, a logical separation can be made on this basis. A. Yellow Iron Oxide Pigments 1. Natural mineral origin a) Goethite b) Lepidocrocite c) Ochres d) Siennas e) Limonite 2. Synthetic pigments a) Goethite B. Red Iron Oxide Pigments 1. Natural mineral origin a) Hematite b) Siderite (calcined) c) Pyrites (calcined) 2. Synthetic pigments a) Hematite C. Brown Iron Oxide Pigments 1. Natural mineral origin a) Umbers b) Limonite (calcined) c) Siderite (calcined) d) Goethite (bog ore or sulfur mud) 2. Synthetic pigments a) Blends of hematite, goethite, and magnetite

Jan 1, 1983

MINING ENGINEERING presents the annual membership report of the Society of Mining Engineers; see page 147.

Jan 7, 1964

By D. J. McAdam

As shown in three recent papers by the author, in two papers by McAdam and Mebs, and in a paper by McAdam, Mebs, and Geil," the technical cohesive strength of a metal, in any particular state as regards mechanical treatment and heat-treatment, cannot be represented by a single stress value, but must be represented by a diagram with the principal stressest as coordinates. Each point on the boundary of such a diagram represents a technical cohesion limit. The technical cohesive strength thus comprises an infinite number of technical cohesion limits, each representing fracture under a specific stress combination. Moreover, neither the yield strength1 nor the ultimate strength can be represented completely by a single stress value, but must be represented by a diagram with the principal stresses as coordinates. All combinations of the principal stresses may be classified in three groups as illustrated by Fig. I. Fig. Ia shows three typical stress combinations with no two principal stresses equal. The magnitude of each principal stress is indicated qualitatively by the length of the arrow. Arrows pointing away from the cube indicate tensile stresses; arrows pointing toward the cube indicate compressive stresses. Typical stress combinations with two principal stresses equal are illustrated in Figs. rb and Ic. Such stress combinations would be produced by subjecting a cylinder to combinations of uniform axial and radial stresses. The uniform radial stress may be resolved into two equal principal stresses. with the mutually perpendicular directions rotatable around the axis of the cylinder. Fig. ib shows stress combinations with Sz equal to The greatest principal stress is in the axial direction, and the stress combination tends to cause either absolute or relative increase in length.* Fig. u shows stress combinations with S2 equal to St. The greatest principal stress is in the radial direction, and the combination tends to cause either absolute or relative decrease in length. The complete representation of either technical cohesive strength, yield strength, or ultimate strength generally requires a three-dimensional diagram. When two of the principal stresses are kept equal, however, the strength of a metal may be represented by a two-dimensional diagram with the coordinates representing the axial and radial stresses.6-II In this paper, attention will be confined almost entirely to stress combinations with two of the prin-

Jan 1, 1945

By C. R. Hayward

CARLE R. HAYWARD.-I do not want it understood that I think that the conclusion that the time of tempering temperature is immaterial has been definitely proven, but since these are the first definite figures put out, I thought before continuing on more work ourselves, it would be well to present them as progress and for information. J. A. MATHEWS, Syracuse, N. Y.-I think that if Prof. Hayward would consult the paper of Profs. Barus and Strouhal,1 1885, he would find about 250 pages, mostly figures, on this subject, in which they investigated the tempering effect by electrical and magnetic methods. There are so many figures in the paper that it is very difficult reading. One point particularly brought out was that even at a low temperature, such as the boiling point of alcohol, about 60° C., there is a tempering effect, increasing up to 4 hr. One reason they obtained those results, with which the present authors are at variance, was that they started with a high-carbon steel which hardens thoroughly, whereas the steel Prof. Hayward and his collaborator used was a comparatively mild steel which does not take a great deal of hardening. About 3 years ago Mr. Stagg and I published 2 a few figures bearing on the same subject, but we used .a low-carbon alloy steel of high tempering qualities and found a great deal of improvement, particularly in ductility, by continuing the drawing up to 4 hr. We used a chrome-vanadium steel showing after heat treatment 250,000 tensile strength. On short drawing, we got almost no ductility, but by continuing to 4 hr., we raised it to 12 per cent. I believe Prof. Hayward's results are due to using comparatively mild steel, whereas Prof. Barus used drill rod and carried out a, wonderfully exhaustive

Jan 4, 1917