Search Documents

By D. C. Lindley, D. H. Gaucher

The displacement of oil by water in a waterflood project is accomplished by the action of transient viscous, gravitational and capillary forces which drive fluid through interconnecting pore spaces toward production wells. The relative importance of each of these forces to the effectiveness of the displacement and the production history depends on properties of the reservoir itself and the manner in which it is operated. There has been considerable discussion'-3 concerning the importance of these factors and the extent to which they control the performance of individual waterflood projects. No data have been presented, however, to demonstrate the effect on waterflood behavior of variations in rock permeability, water-injection rates and mobility ratios in three-dimensional reservoir systems in which viscous, gravitational and capillary forces are allowed to assume the proper relative influence on fluid flow. Much information relevant to water flooding has been gained from the study of field case histories. But, the complexity of the systems involved, the difficulty of defining geometry and obtaining sufficient data, and the fact that the same reservoir is never flooded twice with the same initial conditions, all obscure the role of process variables such as rate. Further, mathematical calculations of waterflood behavior are restricted at this time by available mathematical techniques to highly simplified situations. Scaled models, however, do offer an approach at the present time to evaluation of the effects of the pertinent variables. Several investigators have predicted prototype reservoir behavior from observations of model waterflood performance under a variety of conditions. Two-dimensional aspects of waterflood pattern efficiency have been investigated by Muskat, Aronofsky, Dyes, et al, raig, et al,' and Rapoport, et al. he effects of gravity segregation, viscous fingering and permeability stratification have also been studied in two-dimensional models. Craig, et al," studied the importance of gravitational forces on frontal displacement in three-dimensional models with wells on a five-spot pattern. This work in- vestigates the tendency for water to segregate in homogeneous reservoirs because of gravity and to under-run the oil for a range of water-inject ion rates. The effects of permeability stratifications were investigated by these authors using miscible fluids to simulate water-channeling through permeable strata in systems of negligible capillary force. In this investigation, a three-dimensional model of a five-spot pattern flood was designed to represent typical prototype conditions, and the sand and liquid properties were selected so that capillary, gravitational and viscous pressure gradients were scaled. It was not, however, possible to achieve exact similitude regarding viscous fingering when the more viscous oil was used. The effects of rock stratification on waterflood behavior were studied by changing both the permeability ratio and the position of the more permeable sand stratum in a two-layered, horizontal model. For each type of stratification, constant-rate floods were performed and the rates were varied, in separate experiments, over a tenfold range. To observe the effect of mobility ratio on flood performance, two series of constant-injection-rate floods were performed on the most highly stratified reservoir at a water-oil viscosity ratio of one.

By W. L. Saunders

IMPORTANCE OF ROCK DRILLING. IT has been estimated that the value of the mineral products of the United States is about $2,000,000,000 a year; that about $25,000,000 is expended. annually for explosives and that about double this sum is paid in wages where blasting is done. The value of the mineral products does not adequately express the importance of the industry involved in the excavation of rock and ore because of the enormous sums of money expended in tunnel driving, in quarries, and in open-cut excavation generally. We know that the Catskill Aqueduct in the neighborhood of New York, which is now nearing completion, has cost some $165,000,000 and that about one-third of this may be rated as rock excavation. These illustrations are given in order to call attention to the great importance of an industry the extension and development of which in our industrial life depend so much upon the economics of rock drilling. Reference has been made to the new Catskill Aqueduct. There are three aqueducts leading into New York, each built at periods separated by some 20 years of time. 'The first one, known as the Old Aqueduct, conveys the waters of the Croton river to New York City in a manner which reminds one of the old Roman aqueducts, the ruins of which are still in evidence. The engineers who laid out these old conduits sought to direct their lines around the hills and into the valleys, at all times avoiding the rock. When it was necessary to cross a river or a deep ravine, a bridge or causeway was constructed. High Bridge, over the Harlem river, is an arched masonry viaduct differing in no essential features from the aqueducts of the Romans. When the second Croton Aqueduct was built, about the year 1890, the art of drilling rock had been so far perfected, and the use of explosives, through the invention of dynamite, had become ,so general, that this waterway was planned and executed on straight lines, following rather than avoiding the rock. The second Croton Aqueduct is a tunnel through rock, about 32 miles in length; material gneiss, almost as hard as granite. Its construction was made practicable by sinking

Jan 9, 1913

By David Sinclair

THE dimensions and shapes of mine structures may at present be determined by (1) field experience, (2) structural calculations, and (3) barodynamic tests.§ None of these, however, provide information as to the stresses, their direction and distribution in a mine structure. For the design of pillars, the placing of openings relative to working places such as gangways, haulage levels, etc., this information is desirable. Photoelastic methods provide this and, while relatively new, their appli-cation in all engineering fields is assuming increasing importance. This paper, therefore, will present the method with a few applications to mining, and with sufficient reference for further study by the reader. PART I THE PHOTOELASTIC METHOD The photoelastic method of stress measurement determines the stress distribution in a two-dimensional model by optical means. It makes use of the fact that when a piece of isotropic transparent material, such as glass, celluloid, or Bakelite, is stressed and viewed in polarized** light a picture is seen which indicates by its color bands of light, or fringes, the magnitude of the stresses, their direction and their distribution.

Jan 1, 1940

By Stanley Reichert

The manganese deposits of the Embree Iron Co., Embreeville, Tenn., are thought to be fairly typical and representative of the East Tennessee type of deposit, and so to warrent rather detailed description. The methods used by the Embree Iron Co. for prospecting and mining, and to a lesser extent for milling; should therefore be applicable to other East Tennessee manganese deposits, as yet' undeveloped. Early History and Discovery of Manganese Brown iron ore (limonite) was mined by the Embree Iron Co. at various times from 1890 to 1910. The early method was simply pick-and-shovel mining in open pits. Later hydraulic giants were used and sluice lines carried the ore down the mountain slopes to log washers.. During this phase of mining, manganese ore was discovered under the iron ore in some of the pits. In other areas oxidized zinc ore was found under the iron. It thus happened that the valuable zinc deposits were discovered in 1914. During the World War period, from 1914 to 1918, there was sporadic prospecting for manganese ore among the abandoned iron workings, but the main activity then centered around the recently discovered lead and zinc deposits. It was not until 1934 that manganese mining began in earnest, under the supervision of R. D. Pritchett, Mine Superintendent. Geology of the Manganese Deposits United States Geological Survey Folios 151 (Roan Mountain) and 118 (Greeneville show that Bumpass Cove is a synclinal structure thrust faulted along the southeast flank, but with normal sequence of strata along the northwest flank. Fig, l. shows the areal geology of Bumpass Cove as taken from the folios superposed on the U.S.G.S. -T.V.A. 1/24,000 topographic maps of the Erwin and Telford 7 ½ minute sheets. The manganese mines occur near the contact of the unfaulted Shady dolomite and the Erwin quartzite. This contact zone is deeply weathered, with overburden averaging 40 to 60 ft. thick. The material overlying' the bedrock along this normal contact is a very tough, plastic clay, termed "buckfat" or "ocher" by the miners. It is not a true ocher, however, in the sense of having commercial value. The manganese deposits occur along this "ocher" band. Fig. 1 also shows how the manganese deposits occur along the broad topographic terrace between the 2100 and 2200-ft. contour lines. This terrace lies at the foot the Erwin quartz ridge. Apparently it is the topographic is expression of the deeply weathered zone along the Shady-Erwin contact.

Jan 1, 1941

By J. J. Friel, E. S. Erickson

Dolomite-fluxed pellets of various compositions were made from magnetite concentrate, hematite concentrate and a concentrate containing a natural mixture of both. Physical properties and reduction test results were used to ascertain proper compositions and firing temperatures. These pellets were subjected to physical tests and to reduction tests. Petrographic and electron microprobe examinations were made to evaluate the effect of composition and fining on the phase assemblage. We interpreted our test results in terms of chemistry and microstructure and related these to properties. This approach enabled w to determine the composition best suited to each of the three concentrates. Compared with acid pellets, dolomite- fluxed pellets of the optimum compositions had similar physical properties but swelled less, softened at a higher temperature, and reduced faster and more completely.

Jan 1, 1983

By L. A. Norman

ANOTHER chapter in the history of Mother Lode mining is being written by operations in the Old Eureka mine near Sutter Creek, Amador County, California. During a two-year period (1938-1939), 85,517 tons of ore averaging 0.62 oz. gold per ton were mined and milled, as compared to the production of approximately 210,000 tons of 0.315-oz. gold ore during the preceding seven years. This is a repetition of mining history in the Mother Lode, where a period of prosperity has followed a long period of lean production. The location of this new ore in the hitherto unproductive hanging-wall greenstones and its mining and geological developments are most interesting. HISTORY OF THE OLD EUREKA MINE The Old Eureka mine, also known as the Hayward, Eureka, Hetty Green and Amador Consolidated, is in the most productive 10-mile length of the 120-mile long Mother Lode of California. The mine was first opened in 1852 with operations more or less continuous for the next 30 years. Production during this period amounted to $12,000,000 from an ore shoot 500 ft. long, which bottomed 1700 ft. below the surface. The shaft was continued as a prospect to 2065 ft. on the incline, where work was stopped in 1881. The mine was sold in 1916 by Hetty Green and the shaft deepened to the 3500-ft. level (3212 ft. vertically) by the new owners. Drifts were run on the 1700, 2100, 3000 and 3500-ft. levels, together with approximately 1500 ft. of crosscuts. No ore was found and work was abandoned in 1921. The present owners, the Central Eureka Mining Co., purchased the mine in 1924 after threatened litigation over rights to the rich ore shoot being mined from the lower levels of the Central Eureka mine on the south. Rehabilitation of the shaft commenced in 1926 and in 1930 mining on the old 2100-ft. level was started. While efforts of the previous owners had been directed for the most part toward the area south of the Old Eureka shaft and adjacent to the productive Central Eureka mine, the present owners started drifting northward on the old 2100-ft. level. On the 2000-ft., 2100 and 2300-ft. levels, drifts were run in part along the

Jan 1, 1939

By E. P. Klier, Taylor Lyman

THE structures formed when austenite is quenched to subcritical temperatures and allowed to transform isothermally have been the subject of intensive study since the work of Davenport and Bain.1 Isothermal transformation diagrams summarizing the results of many of these studies have become widely familiar to metallurgists. Of particular interest to metallographers are the dark-etching, acicular products of transformation formed by isothermal reaction below the temperature of maximum velocity of the austenite to pearlite reaction. These products, the bainite structures, can be formed in a wide variety of steels. However, the constitution of bainite is not well understood and divergent views have been expressed as to its mode of formation. In this investigation a combination of dilatometric, microscopic and X-ray methods has been brought to bear upon the problem in the hope of some elucidation of the bainite reaction as it occurs in hypoeutectoid steels. MECHANISM OF BAINITE FORMATION Davenport and Bain1 considered the mechanism of bainite formation to consist of two steps-an allotropic transformation followed by precipitation of carbide. The separation in time of the two processes was considered to be very slight in the upper temperature range and very marked at temperatures just above the martensite range. This concept has been restated by Vilella, Guellich and Bain2 in the form of a definition of the acicular mode of transformation as: The successive, abrupt formation of flat plates of supersaturated ferrite along certain crystallographic planes of the austenite grains; this supersaturated ferrite begins at once to reject carbide particles, (not lamellae), at a rate depending upon temperature. In effect, this is the acicular mode of transformation, even though the temperature be such as to limit the actual life of the quasi-martensite to millionths of a second. The investigation of isothermal decomposition of austenite in certain alloy steels (notably those containing chromium or molybdenum) has revealed that there may be a range of temperatures between the pearlite and bainite reactions in which the austenite decomposes at a relatively low rate.3-6 Further, it is characteristic that in the second region of fast reaction the decomposition of the austenite is incomplete by one reaction but goes to completion by a second reaction. These observations led Wever7 to a description of the bainite reaction as follows: I. The reaction takes place by initial precipitation of a martensitic intermediate structure. 2. In the upper temperature range this structure readily decomposes into ferrite and cementite. In the lower range carbon separates in an unknown form. 3. In the upper temperature range the precipitated carbide nucleates the precipitation

Jan 1, 1944

By W. C. Ellis, M. E. Fine

INTRODUCTION IN the iron-cobalt system there are several property-composition relationships of theoretical importance. The alloys are ferromagnetic exhibiting a maximum saturation at approximately 33 at. pct cobalt;1 the interatomic distances at room temperature show large positive deviations from Vegard's rule;2 and in the region of 50 at. pct cobalt there is an order-disorder transition which has a large effect on other properties. The thermal expansion data for the system have been reported3,4.5,6 only from room temperature to 100°C, and for this temperature range a minimum in coefficient in the region of 50 at. pct cobalt is well established. 3,4,6 This paper reports the expansion properties in the iron-cobalt system for temperatures from 30 to 850°C, shows the correlation with other physical properties, and proposes an explanation for the interrelation. EXPERIMENTAL PROCEDURE The thermal expansivities of iron-cobalt alloys in 10 pct steps in composition were determined from 30 to about 850°C. The major series of alloys was prepared by induction melting from Armco iron and cobalt rondelles with the addition of about 0.6 wt pct manganese. This series was supplemented by three compositions: high purity electrolytic iron, high purity electrolytic cobalt, and an alloy of 52.1 wt pct cobalt prepared from the high purity electrolytic iron and electrolytic cobalt by vacuum-melting. The compositions of both series of alloys are given in Table I. The specimens for measurement were prepared from the cast ingots by first hot-swaging followed in most instances by cold-swaging to 0.180-in. diam rod. Some alloys in the region of 50 pct cobalt, because of inherent cold-brittleness, were swaged hot to the final diameter. The expansion specimens were approximately 2 ½ in. long with flat-ground and polished ends. Before measurement they were annealed in hydrogen for r hr at 900°C. In the apparatus used for the thermal expansivity measurements (Fig I), a modification of that designed by Hidnert and Sweeney,7 the differential expansion between the specimen and vitreous silica was measured by a dial micrometer reading to 0.001 mm. An invar fixture supported the dial gauge, and this fixture, in turn, was connected to a split invar collar which supported the outer silica tube. A pyrex "T" was placed over the outer silica tube and was sealed to the invar collar by Apiezon Q sealing compound. A movable hollow vitreous silica rod which rested on top of the test specimen slid through a flexible rubber diaphragm cemented to the top of the pyrex "T." The specimen rested on a vitreous silica pedestal fused into the outer tube and was kept centered by a silica sleeve. A non-oxidizing atmosphere was obtained by admitting hydrogen into the

Jan 1, 1948

By D. B. Hobbs, L. W. Kempf, R. S. Archer

SILICON is one of the most important elements in the metallurgy of aluminum. It is always present in small amounts in the ordinary grades of "pure" aluminum, and hence in all alloys made therefrom. Within the last few years binary alloys containing up to 13 per cent. of silicon have come into extensive use for castings. Silicon is also added, beyond the amount present as an impurity, in alloys containing one or more other elements such as copper, manganese, magnesium and nickel. The binary aluminum-silicon alloys are not yet heat treated to any extent in commercial practice, although, as will be shown, their properties are affected to a very considerable degree by heat treatment. There are other aluminum alloys that develop higher strength, but the special characteristics of the silicon alloys may well lead to the application of heat-treating processes on a commercial scale. The role of silicon in the heat treatment of aluminum alloys is more important than would be indicated by consideration of the binary alloys alone, because many of the alloys that are heat treated in regular commercial practice contain some silicon in addition to that derived from the aluminum ingot as an impurity. Among these may be mentioned the heat-treated 195 alloy castings, and the wrought alloys 25S, Special 17S and 51S of the Aluminum Co. of America, and the German wrought alloy, Lautal. It is the purpose of this paper to present the results of experimental work and the conclusions derived therefrom regarding the heat treatment of the binary aluminum-silicon alloys. The products heat treated included forgings, chill castings and both "normal" and "modified" sand castings. REVIEW OF LITERATURE The literature on the heat treatment of aluminum-silicon alloys is not very extensive. The following review gives the principal references of which the authors are aware, in which appreciable information may be found.

Jan 1, 1928

By K. G. Davis, P. Fryzuk

A study has been made of the effect of undercooling on the grain structure and solute distribution in small ingots of pure bismuth and of a 100 ppm Ag in bismuth alloy. Autoradiographic evidence shows that in undercooled melts a network of dendrites is formed throughout the melt immediately after nu-cleation. At large undercoolings the dendrites are very thin and closely spaced. The origin of the observed grain morphology can be explained on the basis of information about the mode of solidification revealed by the impurity substructure. WHILE a great number of studies of nucleation in undercooled molten metals have been made, comparatively little attention has been given to the mode of solidification from melts with large undercool- ings. Colligan and Bayles1 and Walker2 have measured the rate of advance of the solid-liquid interface in undercooled nickel melts, but the morphology of the solidifying material remained a matter of speculation. Fehling and Scheil3 have described the grain structure in ingots formed from undercooled melts of nickel, palladium, and copper, and a series of Ni-Cu and Ni-Pd alloys. At small undercoolings, equiaxed structures are observed, the grain diameter tending to increase as the temperature of nucleation is lowered. At greater undercoolings, a columnar structure is developed, while with still further undercooling there is a smaller grain size incorporating rather coarse subgrains. All-bright and Colligan4 examined the grain structure shown by ingots solidified from melts of nickel and of Ni-Ag alloy at an undercooling of 105°C, and concluded that considerable grain growth had taken place after solidification. The object of the present work is to correlate the mode of solidification from undercooled melts with both the grain structure and impurity segregation, using tracers to examine the latter.

Jan 1, 1965

By A. H. Daane, B. J. Beaudry

The Sc-Y and Sc-Zr systems were studied by thermal and X-ray methods. Both systems are characterized by complete solid solubility in the low temperature hexagonal form and in the high temperature bcc form. In the Sc-Y system, there is a minimum in the solidus at 50 at. pct and 1365°C, while the solidus in the Sc-Zr system follows a nearly straight line relationship between the melting point of scandium and zirconium. There is a minimum in the temperature of transition from hexagonal to bcc in the Sc-Y system at 43 at. pct Y and 1175°C; while the temperature of transition is raised in the Sc-Zr system to a maximum of 1415 °C at 30 at. pct Zr. INTEREST in the metals of the first transition series has usually stemmed from their useful properties; however, there is now a great deal of interest in determining the fundamental nature of these metals. Since scandium is the first of these transition metals, a study of the preparation and Properties1 and the alloying behavior of scandium2 was initiated. In a continuing study of the alloying behavior of scandium, the systems of scandium with zirconium and yttrium have been established. Extensive solid solubility in both the Sc-Zr and Sc-Y systems was expected from application of the classical rules of Hume-Rothery. Also, the modified Darken and Gurry plot as suggested by Gschneid-ner3 showed ideal conditions for solubility in the Sc-Zr system with less favorable conditions in the Sc-Y system. The effect of scandium on the transformation temperature of zirconium and yttrium was of interest, since a recent empirical observation by Uly and Burr4 predicted that the solute scandium would raise the transformation temperature of zirconium and lower the yttrium transformation. In addition to noting the validity of the above predictions, the SC-Y and Sc-Zr systems were established. EXPERIMENTAL METHODS Materials. The metals employed in this investigation were crystal bar zirconium, distilled scandium prepared by the method described by Spedding, et al.1 and yttrium prepared by the method described by Carlson, et a1.5 The major impurities present in these metals are listed in Table I in ppm. Alloy Preparation. All the alloys examined were initially formed by comelting the two metals in a nonconsumable electrode arc-melting furnace under an atmosphere of purified helium or argon. The buttons were inverted at least five times and re-melted each time to ensure homogeneity. During preparation of Sc-Zr alloys, approximately 1 wt pct was lost which was attributed entirely to the loss of scandium by distillation. When preparing Sc-Y alloys, approximately 1.5 wt pct was lost, but it was assumed that the intended composition was maintained, since the relative weight lost when arc melting the component metals was nearly the same. Samples weighing 15 to 20 g were prepared for time-temperature thermal analysis, while only 1- to 2-g samples were prepared for the optical pyrometer and X-ray diffraction studies. Thermal Methods. The solidus and the melting points of the metals were determined by an optical pyrometer method described previously.2 The temperatures at which the transformation from hexagonal to bcc occurs were determined by differential thermal analysis. Several points on the solidus and liquidus in the Sc-Y system were also determined by this method and are in good agreement with those obtained by the optical pyrometer method. The procedure followed in the preparation of samples for thermal analysis and the furnace used have been described elsewhere.2'6 Since a limited quantity of scandium was available, most of the alloys were not melted during thermal analysis, thus avoiding contamination by the crucible. The alloy could then be reused and the composition changed by adding the desired quantity of solute to obtain the next alloy. Heat Treatment and X-Ray Methods. In order to ensure homogeneity, the "as arc-melted" alloys Were wrapped in tantalum foil, sealed in quartz capsules and heated at 1100°C for 15 hr and then cooled at a rate of 8 deg per min. Samples for X-ray diffraction were filed from these heat-treated alloys, sealed in 1/8 in. by 1/2 in. tantalum capsules under

Jan 1, 1963

By G. G. Marino, J. W. Mahar

This paper provides an understanding of the behavior and potential damage of homes resulting from sag-type mine subsidence. This is done with extensive research of numerous case histories in Illinois collected by the authors. The house response to subsidence-induced ground displacements are summarized and evaluated. A damage level criteria, specifically developed for residential structures, is presented based primarily on repair costs. Damage levels and the associated subsidence profile characteristics for each case history are compared.

Jan 1, 1986

By M. H. Mueller, P. A. Beck, W. P. Chernock

HARRIS introduced the term inverse pole figure for the diagrams previously used by Barrett' to represent the volume fraction p(a,ß) of material in various orientations with respect to the fiber axis in a specimen with fiber texture. The direction of the fiber axis with respect to the crystal lattice is specified by the two independent angle variables a and ß. In such a diagram p gives the fiber axis density distribution over the various crystallographic directions. The p(a,ß) may be given in a two-dimensional diagram by means of contour lines (p=con-stant) in a stereographic projection. The inverse pole figure incorporates in a single contour line diagram all the information given conventionally in pole charts for various (hkl) reflections and, therefore, it represents a considerable degree of condensation. Also, it gives this information directly in terms of the volume fraction of the specimen in various orientations, and it obviates the necessity of referring back and forth between the various pole charts in an attempt to interpret them in terms of orientations. Inverse pole figures undoubtedly represent the most adequate method for describing a texture in a quantitative manner and, at least in the case of fiber textures, this method is certainly a practicable one. Harris described1 a simple procedure for determining at least the rough outlines of a quantitative inverse pole figure. This method depends on the measurement of the intensity of X-ray reflections from various (hkl) planes lying parallel to the same specimen surface. In the case of a rod, reflections from a plane specimen surface perpendicular to the rod axis (fiber texture axis) are to be used. Harris has shown that the measured intensities I,,, reflected by crystal planes (hkl), aligned perpendicularly to the fiber axis of a specimen with unknown fiber texture, and the corresponding intensity Iu nkl from a random specimen are related to the p(a,ß) value for the unknown texture by the following equation IAkl/I°Aklw=c/c°.p(a, ß) [1] where C and C° re parameters depending on the crystal imperfections (extinction), surface preparation (e.g., thickness of oxide layer), the absorption coefficient in the specimen, effective line breadth, and instrumental factors. The values of the variables a and ß1 defining the crystal orientation, depend only on the indices hkl of the reflecting plane perpendicular to the fiber axis. Since p, as described by Harris1, is normalized in such a way that upon integration over the total orientation range its mean value is 1, the parameter C/C may be calculated approximately by the summation of Eq. l over all available X-ray reflections hkl, corresponding to a set of discrete orientations (rather than by integration over the complete range of orientations represented by the continuous variables a and ß). From the summation of Eq. 1 1/n SI AKL/I° Akl = C/C. SP(a,ß)/n is obtained where, as stated above 2p(a,ß) =1. n Therefore

Jan 1, 1959

By Benjamin F. Merembeck

A mutispectral scanner (MSS) obtains remotely sensed data of the earth's surface in vector form, one vector element for each spectral sensing band of the MSS. Data generated by either airborne or orbiting MSS systems are organized in a lattice of scan lines and elements within scan lines. Each element, called a pixel, is represented by an observational vector and corresponds to a relatively small specific area on the ground. The total observations for a sensed scene frequently are in the millions and are composed of a number of populations, each representing a different land form category. Based on samples from the populations, the mean vectors, or spectral signatures, and the covariance matrices for the categories may be estimated. From these, an among category covariance matrix and a combined within category covariance matrix can be found. The total among category variance is the trace of the among category covariance matrix. Canonical analysis finds a linear transformation matrix such that the first transform variable accounts for the maximum possible part of the total among category variance. Similarly, the second transform variable, orthogonal to the first, accounts for the maximum possible part of the remainder of the total variance, and so on. Such transformation often results in over 95 percent of the total variance accounted for in the first three canonical variables, even though the initial number of spectral bands exceeded twenty. Transformation of bulk data into three canonical variates allows color map products to be developed by assigning each variable to a different basic color. Such color products are believed to be more useful for photo-interpretation than color products resulting from any combinations of three of the initial spectral bands.

Jan 1, 1977

By Raymond E. Birch, Oscar M. Wicken

THE mineral magnesite, formerly the source of nearly all magnesia, now shares this role with brucite, dolomite, and the world's natural and artificial brines. The mineral magnesite is the normal carbonate of magnesium, MgCO3, composed when pure of 47.6 pct MgO and 52.4 pct CO2. It is one of the calcite (CaCO3) group of rhombohedra1 car- bonates, which also includes dolomite, CaCO3.MgCO3, and siderite, FeCO3. Magnesite does not form an isomorphous series with calcite or dolomite; consequently, these lime-bearing carbonates commonly present in magnesite deposits are there only as mechanical mixtures. Magnesite and iron carbonates form a continuous isomorphous series and therefore are inseparable mechanically. The variety of magnesite known as breunnerite is an isomorphous mixture of iron and magnesium carbonates. Magnesite may be either crystalline or amorphous (cryptocrystalline). The former, which includes breunnerite, is often termed spathic magnesite. Crystalline magnesite varies from finely to coarsely crystal- line in texture and has a hardness of 3.5 to 4. The color is white, yellowish, blue-gray to drab, red, pink, black, or mottled. It is seldom found pure but usually contains variable amounts of iron, lime, silica, and sometimes manganese. The color cannot be used as an index of purity. The cryptocrystalline variety is perhaps the more common type but the crystalline variety usually occurs in larger deposits. The amorphous type is fine grained and compact, showing no cleavage. It is usually snow white but sometimes is light to pale orange yellow or buff, owing to impurities. The fracture is conchoidal to uneven and the hardness 3.5 to 5. Silica may be present as inclusions of serpentine, quartz, chalcedony, or other minerals. The lime and iron contents are usually low. In general, amorphous magnesite is somewhat purer than the crystalline variety. The specific gravity of cryptocrystalline magnesite is 2.90 to 3.00. Pure crystalline magnesite has shown a specific gravity of 3.02 but iron

Jan 1, 1949

By A. T. Aldred

HIS note reports the existence of several new scandium intermetallic compounds of the A2B and AB stoichiometries where the A element is scandium and the B element is from group VIII or IB of the periodic table. Alloys were arc melted from high-purity materials using 2-g charges. Typical lot analyses for the materials used are given in Table I. Chemical analyses were not made on the alloys as there was little or no weight loss on melting. After annealing the specimens for 14 days at 600°C and water quenching, metallographic and X-ray techniques were used to determine the occurrence of the various phases. Table II lists the relevant data for the A2B phases. The Ti2Ni structure,2 has ninety-six atoms in a face-centered cubic cell, whilst the Al2Cu structure is body-centered tetragonal.3 The occurrence and stability of the various A2B type phases in transition metal alloy systems has recently been considered by Nevitt.4 The Ti2 Ni-type phases occur over a relatively narrow range of radius ratios from 1.14-1.26 with A partners mainly from the titanium group and B partners predominantly from the cobalt group. This suggests that both a favorable relative size of the atoms and a favorable electron concentration are necessary conditions for the existence of this structure type. A12Cu-type phases involving Ti group elements as A partners are formed with B partners from the cobalt and nickel groups, predominantly the latter, and have a higher radius ratio (1.27-1.29) than the Ti2Ni-type phases. The occurrence of both Sc2Pd and Sc2Co can be rationalized in terms of these considerations but SczNi is anomalous because of its high radius ratio. The radius ratios are calculated from the Goldschmidt CN12 radii and it might be postulated that the scandium atom is reduced in size in the compound. Unfortunately the apparent atomic size of scandium in the compound cannot be calculated from a knowledge of the structure and lattice dimensions. The crystal structure of the Sc2Au compound could not be identified from the powder diffraction pattern, but it is interesting to note that it is isostructural with a series of A2Au phases where A is a rare earth element.5 Pertinent information concerning the AB phases found in this investigation is given in Table 111. All the phases have the ordered bcc CsCl structure. The occurrence and stability of CsC1-type phases have recently been discussed by Dwight,7 who concludes that the relative sizes of the atoms do not appear to be a controlling factor (the radius ratios of all the known phases vary between 0.985 and 1.439) but that the occurrence of the phase is predominantly dependent on the relative positions of the A and B partners in the periodic table. As a measure of the stability of a given CsCl phase it has been customary to define a lattice contraction on alloying, DAB — dAB, where DAB is the AB interatomic spacing as calculated from the Goldschmidt CN8 radii and dAB is the AB interatomic distance in the compound (= v3/2 ao). Values of the parameter DscB -dScB for the compounds found in this investigation are given in column 5 of Table III and are plotted in Fig. 1. If the lattice contraction does in fact reflect the stability of a phase then Fig. 1 shows two very interesting trends when the position of the B partner in the periodic table is considered. Firstly, within any given group the stability increases in order on going from the first to third long period. Secondly, within any given period the stability increases in order as the B partner is taken from the copper, nickel, and cobalt groups. In the case of the second long period, the lattice contraction reaches a maximum at ScRh and then decreases to ScRu. The same trend could

Jan 1, 1962

By L. C. Graton

The federal taxes on incomes and excess profits are of course heavy. In 1917, the value of the mineral production of the United States was a little in excess of $5,000,000,000. The total of federal taxes for that year, for the mineral producing companies, as computed by themselves, amounts, according to tentative compilations, to about $207,000,000, and the total for the comprehensive group of mineral and metal industries to about $766,000,000, which figures represent respectively 9.5 per cent. and 35.1 per cent. of the total tax paid by all corporations. Because of greater complexities in applying the revenue laws to mineral properties than to most other industries, opportunity is afforded for wide differences of view. The taxes indicated above, therefore, are not final and may conceivably be very materially increased. For 1918, the taxes are expected to be still greater, but no compilations are yet available. Taxes at a high rate are to continue indefinitely. The subject is clearly of gravest import to the mining industry in particular. The Commissioner of Internal Revenue, who is charged by law with the administration and collection of the taxes, is determined that these functions shall be performed in a just and businesslike way. Fairness and finality are to be the chief objectives. In view of the peculiar conditions that attach to the tax program as applied to mines and other wasting industries, like oil, gas, and timber, the Commissioner has resorted to professional advice and assistance by manning a Sub-division of Natural Resources with competent engineers, brought in from the several industries, into whose hands he has placed for solution the technical questions involved. These engineers have a two-fold duty: (1) to devote to the solution of these problems their own knowledge and experience; (2) through their acquaintance with their respective industries, and with the men engaged in those industries, to focus upon these problems, by conferences and otherwise, the best opinion of the country. The principal object of this paper is to acquaint the mining profession with the attitude of the

Jan 1, 1923

By L. C. Graton

The federal taxes on incomes and excess profits are of course heavy. In 1917, the value of the mineral production of the United States was a little in excess of $5,000,000,000. The total of federal taxes for that year, for the mineral producing companies, as computed by themselves, amounts, according to tentative compilations, to about $207,000,000, and the total for the comprehensive group of mineral and metal industries to about $766,000,000, which figures represent respectively 9.5 per cent. and 35.1 per cent. of the total tax paid by all corporations. Because of greater complexities in applying the revenue laws to mineral properties than to most other industries, opportunity is afforded for wide differences of view. The taxes indicated above, therefore, are not final and may conceivably be very materially increased. For 1918, the taxes are expected to be still greater, but no compilations are yet available. Taxes at a high rate are to continue indefinitely. The subject is clearly of gravest import to the mining industry in particular. The Commissioner of Internal Revenue, who is charged by law with the administration and collection of the taxes, is determined that these functions shall be performed in a just and businesslike way. Fairness and finality are to be the chief objectives. In view of the peculiar conditions that attach to the tax program as applied to mines and other wasting industries, like oil, gas, and timber, the Commissioner has resorted to professional advice and assistance by manning a Sub-division of Natural Resources with competent engineers, brought in from the several industries, into whose hands he has placed for solution the technical questions involved. These engineers have a two-fold duty: (1) to devote to the solution of these problems their own knowledge and experience; (2) through their acquaintance with their respective industries, and with the men engaged in those industries, to focus upon these problems, by conferences and otherwise, the best opinion of the country. The principal object of this paper is to acquaint the mining profession with the attitude of the

Jan 1, 1923

By R. D. Nelson, S. D. Dahlgren

The conditions of temperature, strain rate, and total strain favoring deformation by grain boundary sliding, slip, or deformation with concurrent recrystallization were evaluated for alpha plutonium. Grain boundary sliding and slip were studied by examining structures formed on polished surfaces with 4.5 pct compressive deformation. The conditions required for recrystallization were determined from compressive deformation us time curves. At 110" C and at a strain rate of 10&apos;per min, deformation was almost exclusively by grain boundary sliding whereas slip was the predominant deformation mode at -10°C and lo-&apos; per min. Defarmation at intermediate tenzperatures and strain rates produced structures showing mixtures of grain boundary sliding and slip. Recrystallization occurred concurrently with deformation only after a critical strain was reached. About 14, 6, and 3 pct strain was required at 105", llO°, and lZO°C, respectively, before recrystallization started, irrespective of the strain rate in the range of lo-&apos;1 to 10&apos;4 per nzin. L HE temperature and strain-rate dependency of the modes of plastic deformation were evaluated for high-purity as-cast alpha plutonium. The techniques used to study slip and grain boundary sliding were similar to those employed previously for alpha plutonium by Bronisz and Gorum,&apos; and spriet.&apos; Recrystallization was investigated using the methods reported by Nelson.3 Bronisz and Gorum&apos; found that slip occurred on more than one slip system at room temperature, and suggested that grain boundary sliding also contributed to the deformation. spriet2 found that deformation was predominantly by slip at room temperature, and observed one to three orientations of slip traces in individual grains. In addition, he deformed polished samples at 10O° C, but concluded that the deformation character of alpha plutonium at 100° C and at room temperature were not essentially different. Several investigators reported that twinning was only occasionally observed.1&apos;2&apos;4 Nelson3 recently found in creep tests that high-purity alpha plutonium would recrystallize concurrently with compressive deformation at temperatures between 25" and 115°C. EXPERIMENTAL PROCEDURE Electrorefined plutonium having less than 300 ppm total impurities was received from Los Alamos Scientific Laboratory in the form of +-in. diarn cast rods. Major impurities were americium, <I00 ppm, and tungsten, (60 ppm. Less than 25 ppm each of other impurities were present. The rods were cut into right half-cylinders 0.35 in. long and 0.25 in. in diam, and the flat faces along the cylinder axes were metal-lographically polished. To avoid loss of the metallo-graphic polish by oxidation, the polished samples were deformed in a silicone fluid heat treating medium contained in a chamber evacuated to a pressure of lo-&apos; torr. Deadweight loading was used to compress the samples between 4.5 and 20 pct at strain rates between 10"4 and lo- &apos; min-&apos;. Strain rates were determined by dividing the total deformation by the elapsed time of the test, even though the strain rate was not constant during deformation. Curves of strain vs time for samples deformed with a constant compressive stress3 show that the strain rate changes by less than a factor of four during the testing of a given sample, which is small compared to the three orders of magnitude change in strain rate investigated. Two samples were loaded into an ordinary metallographic mounting mold and impacted by striking the mold piston with one blow of a 2-lb hammer. Deformation temperatures for the two impact samples were 25" and 90°C. The samples, following deformation, were washed in carbon tetrachloride and their polished and deformed surfaces were immediately inspected metallographi-cally. Subsequently, the deformation structures were replicated with acetate replicating tape for later electron microscope examination, and the samples were then repolished and etched to reveal the microstruc-tures of the deformed metal. Second-stage carbon replicas were prepared from decontaminated acetate replicas using the procedure developed by Miller, Bierlein, and astel.&apos; Additional samples, which were 0.35 in. long by 0.25 in. in diam, were used to obtain constant load deformation vs time curves. These samples were deformed 10 to 20 pct with loads of 15 and 20,000 psi at 120°C; 30, 45, and 55,000 psi at 110°C; and 20 and 30,000 psi at 105°C. Samples were polished and etched to determine whether or not recrystallization or twinning had occurred during deformation. RESULTS AND DISCUSSION The experiments showed that alpha plutonium deforms by grain boundary sliding, slip, and deformation with concurrent recrystallization. Deformation by twinning was insignificant. Metallographic examination of polished and deformed surfaces revealed grain boundary sliding and slip. The start of recrystallization was ascertained from constant load deformation vs time curves. Deformed surface structures of samples compressed 4.5 pct under four different conditions of temperature and strain rate, Fig. 1, show how the deformation mode changes from predominantly grain boundary sliding to predominantly slip with increasing strain rate and decreasing temperature. Deformation at 110°C and 10" 4 min-&apos;, Fig. l(a), was predominantly by grain boundary sliding. Only a few slip traces can be seen in Fig. l(a).

Jan 1, 1969

By R. J. Wysor

Since the outbreak of the European war, few problems of raw-material supply have commanded more nation-wide attention than potash. It is well known that before the war the domestic production of potash was an insignificant percentage of the imports. The average annual importation of raw potash salts for several years prior to 1914 was slightly over 300,000 net tons, and of other potash manure salts about 700,000 tons. The sudden and almost total cessation of these imports created a unique and stringent situation. Methods of recovering potash from feldspar and other native mineral sources, and reclamation from hitherto waste products, have received a marked impetus. Soaring prices have been a keen incentive to research and industrial development. Although several brief articles concerning the possibilities of potash recovery have appeared in recent trade journals, it still may be a matter of some surprise to the average technical mind that potash might be reclaimed as a profitable byproduct in the manufacture of pig iron. At the present time it may be of special interest to present some data, largely of a technical nature, on this subject. A fairly thorough search of the literature reveals a number of articles concerning salts of the alkali metals in the blast furnace. Many of them deal with the theoretical rôle of alkali cyanides in the furnace. Several discuss the probable effect of the alkalies on the furnace brickwork. Two or three ambitious patents have been granted for reclaiming potash or other products from blast-furnace gas. However, we have heard nothing further as to the practical application of these patents. Little literature of importance has appeared during the last 10 years concerning alkalies in blast-furnace practice, and I have discovered no record whatsoever as to the actual sale or commercial disposal of flue dust for its potash content until this was inaugurated in our plant at Bethlehem. A bibliography of the most important articles discovered is appended. About 4 years ago, in the course of investigating blast-furnace stove efficiencies, I analyzed the fine, yellowish fume of which a considerable

Jan 1, 1917