Search Documents

By H. W. McQuaid, E. W. Ehn

It is usually assumed that chemical specifications are sufficient for steel to be used for case carburizing, and if the steel analyzes within the ordinary limits specified for steel for this purpose, no difficulty traceable to the steel used should be encountered in obtaining satisfactory results in the case carburizing and hardening. Much work has been done to determine the effect of various alloying elements on the rate of carbon penetration, etc. but, to our knowledge, little if anything has been published in regard to the effeet of the quality of the steel on the final results in the hardening of case-carburized steel parts. The writers believe that the structure of the case both before and after quenching is greatly affected by the actual condition of the steel itself as made, and that for good results in the case-carburizing and hardening departments, the steel should be of the best possible quality as regards non-metallic impurities. It is the purpose of this paper to prove that the presence of excess dissolved oxides in the steel, as made in the melting furnace, affects permanently the results obtained in carburizing and hardening and that it is possible that the presence of dissolved oxide call result in total unfit-ness of low-carbon steel for case hardening purposes. When races and rolls for roller bearings are made from a low-carbon steel, case carburized and hardened, it is of primary importance that the results of this treatment be of the highest quality. It is necessary, therefore, that in the case-carburizing work each detail be rigorously checked to avoid any defects which would cause the loss of much time and material. The case carburizing with which this paper deals was done in under-fired oil furnaces. The temperature of each furnace is controlled by means of a platinum platinum-rhodium thermocouple, in connection with a potentiometer indicator and potentiometer recorder. The temperature of each furnace is registered every 15 min. by an operator, who is continually checked by the automatic recorders.

Jan 1, 1922

By J. B. Clemmer, P. E. Churchward, C. Rampacek

A cyclic method for processing manganese ores using sodium sulphate as the basic reagent is described. Sodium sulphate is electrolyzed in a diaphragm cell to give an anolyte-containing agentisdescribed.Sodiumsulphuric acid and a catholyte-containing iselectrolyzedincaustic soda, a part of which is carbonated in a cyclic manner to form soda ash. The reduced ore is leached with the anolyte to dissolve the manganese and the impurities are precipitated by addition of catholyte. Manganese in the pregnant todissolvethemanganeseandtheimpuritiessolution is precipitated as synthetic rhodochrosite with a carbonated catholyte, and sodium sulphate is regenerated. Calcining the manganese carbonate gives a high grade product and the carbon dioxide is returned to the carbonation step. The results of laboratory tests using cells equipped with synthetic-fiber diaphragms and permselective membranes, which permit transfer of anions or cations during electrolysis, are described. A METHOD which has been considered for pro-cessing manganese ores under emergency conditions to recover a product suitable for smelting to ferromanganese involves reductive roasting of the ore for leaching with dilute sulphuric acid followed by precipitation of the manganese from the purified pregnant solution with sodium carbonate. Although the process is operable and involves no novel or untried steps, it is noncyclic in regard to reagents. Research seemed warranted to determine if a cyclic process could be developed by electrolyzing the sodium sulphate formed during precipitation of the manganese with soda ash to regenerate sulphuric acid and sodium hydroxide. Reduced ore would be leached with acid anolyte to dissolve the manganese. The iron, alumina, and other dissolved impurities would be precipitated with the caustic catholyte, and the manganese in the purified pregnant solution would be precipitated as artificial rhodochrosite with carbonated catholyte to regenerate simultaneously sodium sulphate for electrolysis. Waste boiler gas and CO, from calcining the manganese precipitate would be recycled for carbonation of the caustic catholyte. There is a surprising lack of data in the technical literature on diaphragm electrolysis of sodium sulphate. One of the more comprehensive papers, by Atwell and Fuwa, describes the problem involved in electrolyzing byproduct sodium sulphate from the viscose process with particular regard to the design and operation of asbestos diaphragm cells. Frisk' also investigated electrolysis of sodium sulphate from viscose-spinning baths to recover caustic soda and sulphuric acid. The objective in these investigations was to produce, by electrolysis and evaporation, a concentrated caustic-soda solution and a sulphuric-acid solution low in sodium sulphate. Because of these requirements, the process was not too attractive despite a favorable yield of caustic and acid with a reasonable power consumption. Because strong acid and base are not required for processing manganese ores and nonelectrolyzed sodium sulphate is not objectionable in either reagent, the present problem was somewhat simpler than that of these investigators. The purpose of this report is to summarize briefly the results of laboratory electrolysis of commercial sodium sulphate in diaphragm cells of different types and the application of the acid and caustic for processing manganese ores in a cyclic manner. Electrolysis in Permeable Diaphragm Cells The principal problem in electrolyzing sodium sulphate in a permeable diaphragm cell is to prevent mixing of the acid and base formed in the anode and cathode compartments. It is not enough to separate the anolyte and catholyte by a single diaphragm. A three-compartment cell in which the sodium-sulphate solution is fed to the center compartment and flows through the permeable diaphragms to the anode and cathode compartments is more efficient electrically. Diaphragms should be porous enough to allow flow of solution to outer compartments but tight enough to prevent gross mixing of the anolyte and catholyte. In addition to being resistant to acid and alkali, the diaphragms should offer minimum resistance to the flow of current. It is also important that the electrolyte contain a high concentration of sodium sulphate to furnish an abundance of sodium and sulphate ions and thereby decrease the current carried by hydrogen and hydroxyl ions. A practical limitation of sodium-sulphate concentration is imposed by the decreased solubility of sodium sulphate with decreasing temperature. At 20°C, a concentration of 200 g per liter sodium sulphate can be maintained. Little is gained in conductivity by using a concentration greater than 200 g per liter. The small-scale continuous electrolysis tests were made in a 12x12 in. open-top bakelite cell equipped

Jan 1, 1956

By J. Chipman, G. G. Hatch

One of the important functions of the iron blast furnace is the desulphur-ization of pig iron before it enters the steelmaking furnaces. However, the increasing concentrations of sulphur in the metallurgical coke, source of approximately 90 pct of the sulphur present in the blast furnace charge, and demands for higher rates of production within recent years have increased the need for greater desulphurization within the iron blast furnace. Furnace operators are beginning to look for desulphurizing agents other than blast furnace slag to accomplish the desired degree of desulphurization. A considerable amount of work has been done on desulphurization outside the furnace with soda ash, calcium carbide and various synthetic slags. Whether the desulphurization of pig iron is accomplished wholly inside the furnace or partly inside and the remainder outside, will be determined by the economics involved. Regardless of which is the case, it is believed that it is necessary to have a better understanding of the physical chemistry of desulphurization by blast furnace slags. To this end, it is the object of the present investigation to attempt what is believed to be the first equilibrium study of the distribution of sulphur between liquid pig iron and a wide range of blast furnace slag compositions. Review of Literature There is a considerable amount of information in the literature concerning the desulphurizing power of iron blast furnace slags, the solubility of various sulphides in the slags, and the effect on desulphurization of temperature, of elements dissolved in the liquid iron, and of viscosity. However, there is nothing to indicate that the equilibrium distribution of sulphur between liquid iron saturated with carbon and iron blast furnace slags has been studied experimentally. Wentrupl has made probably the most detailed study of the desulphurization of pig iron to date. He considered that there are three distinct aspects involved, namely: 1. Desulphurization within the blast furnace (by lime and manganese). 2. Subsequent desulphurization by manganese. 3. The effect of subsidiary reactions on the desulphurization by manganese. The experimental work carried out by Wentrup was devoted mainly to obtaining a better understanding of how desulphurization by manganese was accomplished in the mixer and the ladle. Particular attention was given to the part played by carbon, silicon, and phosphorus associated with manganese in the iron, and the effect of temperature on desulphurization. The experimental results indicated that desulphurization by manganese is purely a process of crystallization of manganese sulphide. The addition of silicon to iron melts containing 3.5 pct carbon and less than 0.5 pct manganese had no noticeable effect on desulphurization, but with 1-2 pct manganese the silicon additions improved the desulphurization. Additions of phosphorus also resulted in improved desulphurizati011 by manganese, but the effect was not as marked as in the case of silicon. It was also found that desulphurization by manganese was further improved by lowering the temperature. In order to explain desulphurization inside the blast furnace, Wentrup considered the system iron, sulphur, calcium, oxygen, manganese. (silicon). The distribution of sulphur between the metal and slag was represented by the following equation: (SS) _ (S)Fe + (S)Ca + (S)Mn .... [S] = [s] [1] The parentheses and the brackets represent the equilibrium concentrations in weight per cent of the slag and metal constituents, respectively. Since FeS D (FeS) _ (FeS) (S)Fe LfeS - [FeS] [S] [2] (CaO) + S e (FeO) + (S)Ca _ (FeO)(S)Ca. (S)Ca _ (CaO) Kl = (CaO)[S] [S] ~K1(FeO) [3] Mn + S D (S)Mn (S)Mn (S)Mn K' = [MnpT "1ST = *lIMnJ !4) Substitution of Eq 2, 3, and 4 into Eq 1 resulted in if = L- + *> (Sol + K^ (S) [51 Eq 5 was used to calcu1;lte -f^j and [S] at 1480°C for slags containing 30-50 pct lime, 0.1-2.5 pct iron oxide, 0-26 pct silica, 2 pct sulphur and iron analyzing 1.5 pct manganese. The value for LFaB at 1480°C was found to be equal to 4.5, based on the experimental work of Bardenheuer and Geller.2 The results of the calculations are shown in Table 1. Although the slags are hypothetical and do not represent the range of compositions found in ordinary blast furnace practice, the calculations indicate that lime is effective in controlling desulphurization only if the iron oxide and silica contents of the slag are kept low. Schenck3 did not claim K1 to be a true equilibrium constant, but an empirical value which varied with the silica content of the slag.

Jan 1, 1950

By M. H. Yoo

Possible interactions of the perfect dislocations of six slip systems or the c dislocation with the (10i2f (ioii), {ioIi}(ioiZ), {1122}(1123), and {1121}(ii26) type twins in hcp metals have been analyzed from the crystallographic and the energetic points of view. Twenty-six distinct types of possible interactions were identified, and those selected based on crystallographic constraints were examined for their energetic feasibilities by use of the anisotropic energy factors. No long-range elastic interaction exists for a dislocation when its Burgers vector is parallel to the twin interface. Under a suitable applied stress, a screw dislocation can cross slip at the twin interface. For basal mixed dislocations in cadmium and zinc, the interaction with {1012} twins is found to be attractive, indicating that incorporation of these dislocations into the twins is energetically feasible and that twin growth will result. On the other hand, the interaction between both basal and Prism mixed dislocations and the {1012} and (1121) twins is found to be repulsive in Mg, Co, Re, Zr, Ti, Hf, and Be. This indicates that under an applied stress a local stress concentration will develop due to a dislocation pileup at the interface, which may result in a site for either the nucleation of other twins or the formation of a crack, depending on the cleavage strength. WHEN a metal undergoes plastic deformation, a certain configuration of slip dislocations will result in a state of dislocation pileup against an obstacle. The stress concentration thus developed may enhance the process of twin nucleation and also twin growth. Furthermore, once formed and dispersed in the crystal, twins can act as effective barriers against slip dislocations. The degree of such mutual influence or interrelation between slip and twinning is generally known to be pronounced in the case of hcp, metals. It is also known that deformation by twinning occurs more commonly in hexagonal metals than in cubic metals. In fact, under suitable stress states, all hexagonal metals exhibit {1012) <1011> type twinning.&apos; In addition to this common type, deformation by (1151) <1126> type twinning occurs in zirconium, titanium, and rhenium, which show remarkable ductility.&apos; The importance of twinning during general deformation to the ductility of hcp polycrystals has been briefly discussed in recent review works.2&apos;3 The purpose of this paper is to analyze the interaction between slip dislocations and twins in the hcp structure and to discuss the nucleation and growth processes of twinning and the role of twinning in the <"°" noil) o, 1/3[112O] (OOO2) 1/3[1123] Fig. l—-Slip systems in hcp structure. ductility of hexagonal metals. The problem will be discussed from the geometric and the energetic points of view in a manner similar to that of the previous work on zinc.4 Since hcp crystals deform by several slip and twin systems, numerous interactions result as possibilities. The Burgers vectors of six slip systems and the c dislocation shown in Fig. 1 and the four twin systems listed in Table I are considered here. A complete tabulation of the possible interactions is followed by discussion of those that are more likely to occur on the basis of crystallographic constraints and energetic considerations. 1) CRYSTALLOGRAPHY OF TWINNING The crystallographic elements, K1, K2, n1, and n2, for the four compound twin systems are now well established.= A unit cell with the base vectors n1, and n2 is shown in Fig. 2 for each twin system. The unit cell before twinning is shown in solid line, and the corresponding unit cell after twinning is shown in dashed line. Also shown in Fig. 2 are the following crystallographic parameters: S is the plane of shear, d the interspacing of the twin habit planes K1,Ø Iis the acute angle between n1, and n 2, e is a numerical factor, and q is the number of K, lattice planes intersected by 17&apos;. These parameters can be expressed in terms of the axial ratio, y = c/a, as listed in Table 11. The macroscopic shear strain of twinning, s, and the magnitude of a "unit twin dis-l~cation,"4 bt, are also expressed in terms of y and given in Table 11. In Table 11, K1 and q1 are given in both Miller-Bravais and Miller indices. In double lattice structures, shuffling of atoms in addition to a homogeneous shear of the lattice is generally required if the original crystal structure is to be restored after twinning. The extent of current understanding on this problem of atom shuffling is per- Table I. Four Twin Systems in Hcp Structure

Jan 1, 1970

By G. F. Olsen

ON superficial consideration a technical library might be considered a luxury to the business institution that possesses one. After all, public libraries and research institutions probably contain all the data that would be found in a private technical library, and able consultants are available both within and without a company. In all probability the technical men of a company have in their combined personal libraries sufficient information to answer most inquiries. Nevertheless, possession of such a department is of real economic benefit because of the time it saves its users, because it prevents expensive duplication of technical literature in a company, and lastly, but most important, be- cause it makes readily available a central storehouse of technical facts classified and indexed to meet the demands of the industry or industries concerned.

Jan 1, 1940

By H. A. J. Wilkens, H. B. C. Nitze

From time to time papers treating of specific cases of Southern gold-mines and mining have appeared in the Transactions of this Institute, as well as in other journals and publications. Mr. George I?. Becker, of the United States Geological Survey, made a reconnaissance of the Southern Appalachian gold-belt during the fall of 1894; the results of his investigations are published under the title of "A Reconnoissance of the GoldFields of the Southern Appalachians," in the Sixteenth Annual Report of the Director of the United States Geological Survey, 1894-95 : Part III., " Mineral Resources of the United States." Mr. Becker has treated the subject mainly in a scientific geological manner. We present this paper to the members of the Institute as requested by the Secretary last May, with the object of covering the ground from a more practical and technical standpoint. The notes for this paper were made in a large measure from personal observations, gained chiefly during the past summer on a trip through the field. In connection with this trip we collected a suite of typical hand-specimens, representing the gold-ores and wall-rock from the more important localities. This collection forms a part of the exhibit

Jan 1, 1896

By Albert Brokaw

THE so-called ?paraffin dirt" of the Gulf Coast oil fields has been con¬sidered an indication of the possible presence of oil and gas, and not a few wells have been brought in solely on the basis of such evidence. In a sense, it may be empirically justified as evidence of the presence of oil or gas, though it cannot be said to be infallible. If the writer is correctly informed, its association with oil and gas was pointed out by Lee Hager some years ago, and while it is commonly mentioned by geologists and operators in conversation, no discussion seems to have found its way into print. The present interpretation is based on laboratory study rather than on field investigation, and is put forth with the hope of stimulating discussion which shall lead to more complete understanding. The term "paraffin dirt" has been applied to soils with a peculiar texture, which has been described&apos; as "curdy" or "rubbery." When moist, the material breaks much after the fashion of "green" cheese. It is rubbery under compression, but does not resemble rubber in tenacity or cohesion. When dry, the material ranges from hard clods to a horny mass of high tensile strength. The shrinkage in drying is very great, especially in the hornlike matter. The moist material ranges in color from dark brown in the specimens rich in organic matter to grayish in specimens containing more inorganic matter. All of the specimens studied were readily attacked by molds, which in some cases grew in great profusion on the samples. Samples exhibited a rather characteristic "swampy" or "mucky" odor when wet, and a characteristic odor of humic soils when moist.

Jan 4, 1918

By Louis E. Reber

Jan 1, 1922

By PAUL DYER MERICA

PAUL DYER MERICA, who has been awarded the James Douglas Gold Medal for his achievements in non-ferrous metallurgy, is a Hoosier, having been born at Warsaw, Ind., in 1889. His father, a clergyman and educator, was president of the University of Wyoming from 1908 to 1913. After graduating from the University of Wisconsin in 1908, young Merica (not yet twenty years of age) went to China, where he was professor of chemistry in Chekiang Provincial College, Hangchow, until 1911. He then went to Germany to s t u d y and was fortunate enough to receive his Ph.D. from the University of Berlin just a few months before the outbreak of the World War in 1914. Returning to America, his first position was as special investigator at the En¬gineering Experiment Station of the University of Illinois, but before the year was out he joined the staff of the U. S. Bureau of Standards as associate physicist. Since 1918, he has been superintendent of research for the International Nickel Co. His work during those years is excellently summarized in the following quotation from the statement of Zay Jeffries recommending him for the award.

Jan 1, 1929

By R. E. Heithecker

Almost every oil well drilled into limestone formations in Kansas is treated with hydrochloric (muriatic) acid upon completion: to increase potential capacity of well and thereby increase its "daily allowable" production; to shorten time required to produce recoverable oil; and to increase quantity of oil recovered ultimately from reservoir. Acid treating marked a forward step in the producing fields of Kansas; in fact, many old limestone fields that almost had reached their economic producing limit were "rejuvenated" with acid and their capacities to produce increased several times. It also caused a marked increase in the ultimate oil recovery of some old and nearly depleted fields of Kansas. The effect of the acid was due to the cleaning-out action by the acid at the face of the limestone, the enlargement of the small drainage channels, and the apparent penetration of the acid to previously undrained porous and saturated strata. Studies of the effects of acid were made in the Fairport field, three groups of wells in the El Dorado field and the Shutts field. Estimation of increased recoveries resulting from acid in these fields and groups of wells ranged from 1000 to 2400 bbI. per acre. Limestone structures that had been tested by drilling and found noncommercial were later completed as commerical oil-producing formations through the use of acid. The Kansas City formation, Valley Center field of Kansas, is an example. Increased oil production and revenue from the old fields justified the reconditioning of equipment, which in most cases had become in poor mechanical condition. The first treatment with hydrochloric acid of an oil well in Kansas was in October 1932, and by the end of 1937 almost 6000 wells had been treated. Many wells were treated more than once and the total number of treatments exceeded 8000 by the end of 1937. Approximately 12 3/4 million gallons of acid was required for these treatments. The report includes 15 illustrations and 16 tables.

Jan 1, 1939

By R. E. Heithecker

Almost every oil well drilled into limestone formations in Kansas is treated with hydrochloric (muriatic) acid upon completion: to increase potential capacity of well and thereby increase its "daily allowable" production; to shorten time required to produce recoverable oil; and to increase quantity of oil recovered ultimately from reservoir. Acid treating marked a forward step in the producing fields of Kansas; in fact, many old limestone fields that almost had reached their economic producing limit were "rejuvenated" with acid and their capacities to produce increased several times. It also caused a marked increase in the ultimate oil recovery of some old and nearly depleted fields of Kansas. The effect of the acid was due to the cleaning-out action by the acid at the face of the limestone, the enlargement of the small drainage channels, and the apparent penetration of the acid to previously undrained porous and saturated strata. Studies of the effects of acid were made in the Fairport field, three groups of wells in the El Dorado field and the Shutts field. Estimation of increased recoveries resulting from acid in these fields and groups of wells ranged from 1000 to 2400 bbI. per acre. Limestone structures that had been tested by drilling and found noncommercial were later completed as commerical oil-producing formations through the use of acid. The Kansas City formation, Valley Center field of Kansas, is an example. Increased oil production and revenue from the old fields justified the reconditioning of equipment, which in most cases had become in poor mechanical condition. The first treatment with hydrochloric acid of an oil well in Kansas was in October 1932, and by the end of 1937 almost 6000 wells had been treated. Many wells were treated more than once and the total number of treatments exceeded 8000 by the end of 1937. Approximately 12 3/4 million gallons of acid was required for these treatments. The report includes 15 illustrations and 16 tables.

Jan 1, 1939

SUDBURY ore processed by International Nickel Co. of Canada Ltd. was recovered for many years as two mill concentrates, one primarily of copper, and the other mixed pentlandite-pyrrhotite, But, Since iron content of the nickeliferous pyrrhotite concentrate was ten times its nickel value, capacity of smelting was limited by the need for slagging the excess iron. A process for recovering the iron con- tent was developed after some years of research and a $20-million plant was constructed to employ the new method. Built near Copper Cliff, Ont., the plant started operation early in 1956, scheduled for separate treatment of 365,000 tons of pyrrhotite each year. It is only the first unit of an installation which will have a capacity of more than 1 million tons per year of pyrrhotite. By early 1958, production totaled more than 200,000 long tons of 68 pct Fe pellets containing 0.003 pct P, 1.5 pct SiO2, 0.01 pct S, and 0.15 pct Ni.

Jan 8, 1958

By H. I. Aaronson, C. Wells

THIS is a preliminary report on a detailed metal- lographic investigation of the bainite reaction in a plain carbon hypoeutectoid steel. In view of the current interest in the bainite reaction and of the controversies which still exist about even the basic phenomenology of this mode of transformation, it was considered desirable to present a summary of the more important results obtained to date prior to the completion of this investigation. The steel used contained 0.29 pct C, 0.76 pct Mn, 0.25 pct Si, 0.005 pct P, and 0.007 pct S. The alloy was homogenized for 48 hr at 1250°C. Individual specimens were then austenitized for 30 min at 1300°C and isothermally transformed for various times at temperatures above and within the bainite region, ranging from 775" through 500°C at intervals of 25°C. These specimens were carefully examined on a research metallograph; a few specimens of especial interest were also studied electron microscopically.&apos; Bainite may be defined as the aggregate structure resulting from the precipitation of carbides from supersaturated ferrite which formed by nucleation and diffusion-limited growth. Two groups of experimental observations made during the present study provide support for this mechanism of the bainite reaction: 1—at 625°C, partial conversion of pro-eutectoid ferrite to bainite began after more than 99 pct of the austenite had decomposed and 2—the precipitation of bainitic carbides occurred only within the ferrite phase. The proeutectoid ferrite and the bainite reactions in the steel studied were found to be morphologically continuous. Following the classification scheme of Mehl and Dube,2 three principal morphologies of proeutectoid ferrite were identified in the temperature region (625" to 550°C) in which the two reactions blend—grain boundary allotriomorphs," * Grain boundary allotriomorphs are crystals which nucleate at and grow preferentially along matrix grain boundaries. Widmanstaetten side plates, and intragranular plates. Carbide precipitation converted these morphologies into their bainitic equivalents with increasing isothermal reaction time. Conversion took place more rapidly as the reaction temperature was reduced. The replacement of supersaturated ferrite by bainite, however, did not occur uniformly even within individual austenite grains and was noticeably incomplete at higher transformation temperatures, e.g., 625° to 575°C. The ferritic and bainitic forms of a given morphology thus were frequently found to coexist, often inextricably intermixed, in a given specimen. At 625" and 600°C, the conversion of ferrite to bainite was clearly seen to have occurred entirely by the nucleation of carbides at ferrite/ferrite boundaries, as shown in Fig. 1. The nature of the loci at which carbides formed at lower temperatures was often difficult to ascertain with a light microscope, although the alignment in rows of many of the carbides, illustrated in Fig. 2, suggested that nucleation had again occurred at grain boundaries or subboundaries within the ferrite. Application of the electron microscope confirmed this deduction for bainitic structures formed at these temperatures, as shown in Fig. 3. The dense black appearance of bainite formed at very low reaction temperatures in higher carbon steels3 indicates, however, that isolated lattice defects within ferrite crystals prob-

Jan 1, 1956

By William M. Baldwin

Jan 1, 1946

By William M. Baldwin

Jan 1, 1946

By H. Vincent Wallace

ALTHOUGH it is universally accepted that free oxygen is A necessary in a cyanide solution for the dissolution of gold and silver-in accordance with Elsner&apos;s equation that 2Au + 4KCN + 0 + H20 = 2KAu (CN), + 2KOH- little has been written and insufficient attention paid to the drop in extraction due apparently to loss of dissolved oxygen in mill solutions. Aeration or oxygenation of cyanide solutions has been more or less successfully accomplished by various types of agitators such as the Dorr (with or without air lifts), Pachuca tanks and more recently "Turbo-mixers" and Denver "Super- agitators"; also by the introduction of chemical oxidizing agents such as Solozone (Na,O,) . At the Wright-Hargreaves and other mines in the Kirkland Lake camp, the introduction of this reagent at the rate of about 1.25 oz. per ton of ore applied to the feed of the ball mills has certainly been beneficial.

Jan 1, 1932

By Gilbert E. Doan

WHEN metallurgists and other engineers meet their college classmates or former teachers, the conversation will frequently become reminiscent and finally turn to engineering education. These graduates have tested the value of their college training in the hurly-burly of the outside world so respectful attention is due their opinions, which, strangely enough, fall into two opposite categories. A member of one group expresses a deep-seated conviction that engineers should have a fuller foundation of physical chemistry, another asks for a more thorough training in mathematics, others wish a more thorough grounding in refractories, a series of courses in petroleum engineering, or in electric welding. Each alumnus of this group

Jan 1, 1937

By R. Chanchani

Single and mixed mineral flotation behavior and the mechanisms for the loss of selectivity in 1:1 and 95:5 apatite: dolomite mineral mixtures are presented. Loss of selectivity in mixed mineral systems is attributed to depletion of oleate ions available for adsorption by bulk precipitation with calcium and magnesium ions dissolved from dolomite. Flotation after two-stage conditioning was found to be a potential technique to separate dolomite from apatite. This method involves conditioning at pH 10 followed by reconditioning at a lower pH. The results indicate that selective flotation of dolomite, a minor mineral in south Florida phosphate deposits, could be obtained by reconditioning at pH below 4.5. Higher selectivity was observed for mixed minerals as compared to that of single minerals.

Jan 1, 1986

By D. R. Walker, M. C. Shaw

Dimitri Kececioglu (Allis-Chalmers Manufacturing Co., Milwaukee)—The idea of applying metal cutting theory to comminution and vice versa is very impressive. Among others, the demarcation of wheel-grinding data into two regions, namely Kick&apos;s and Rittinger&apos;s, draws attention here. A study of Figs. 6 to 9 shows the following: In Fig. 6, 1 point out of 8; in Fig. 7, 4 points out of 26; in Fig. 8 only 1 point out of 13; and in Fig. 9 practically none out of 13 points fall out of curve No. 2. Also when grinding particles smaller than 5x10." in. it is difficult to measure very accurately the grinding forces, chip geometry, and particle size. In view of the above it would be difficult to make a positive and distinct demarcation of the Wheel-grinding data into two regions, namely, Kick&apos;s and Rittinger&apos;s. The idea of using machine grinding to determine the comminution properties of materials is indeed unique. The following cautions come to mind, however, regarding applicability of machine grinding data to comminution: 1—Grinding gives uniform particle size, whereas comminution gives a variety of particle sizes in the same process. The fact that grinding gives uniform particle size is not necessarily an advantage because in comminution the overall energy under actual comminution is desired and comminution invariably results in the production of a variety of particle sizes. 2—In grinding, a small particle is ground off a comparatively large surface. In comminution small bodies are broken down to smaller bodies. This makes it difficult to establish a concept of reduction ratio in machine grinding. 3—The mechanics of machine grinding involve direct shearing action under very high strain and comparatively high compression at the shear zone, whereas: comminution involves direct dynamic compression and surface friction with comparatively little strain and shear. Consequently the mechanics of machine grinding appear to be different from those involved in comminution. Hence one might arrive at erroneous con- clusions when comminution characteristics are eval-uated from machine grinding results. It is noticed also that functions other &apos;than Eq. 16 which do not involve the concept of direct proportionality of useful energy input to new surface area created (Eq. 2 and particularly Eq. 12) may be derived to fit the, data of curve No. 2. One such relationship may be u = ct-", where c is a positive constant and n is a positive constant less than unity. This, of course, is made possible because data of a very small range. of particle size are being fitted by the curves of No. 2 and the hereby suggested relationship. A sound comminution theory should be applicable to a relatively large range of particle size. George B. Clark (Department of Mining Engineering, University of Illinois)—While the experimental work of Walker and Shawin this article is of intrinsic value in revealing certain fundamental aspects of machine grinding, milling, and related processes and in adding to the store of information concerning the comminution of solid materials by this particular process, it appears doubtful that the results of their research can be employed to verify either Kick&apos;s or Rittinger&apos;s theories. Both these laws were originally developed and proposed on the basis of very simple, idealized hypotheses. The creation of parallel idealized physical laboratory conditions which would be required for either their proof or disproof appear to be well beyond the scope of human ingenuity, at least at present. One great weakness of the imputed verification is that the spread of the points plotted on the graphs is not sufficient to permit accurate &apos;curve fitting. The range of particle sizes included in the belt and wheel grinding is not extensive enough to show any general trends, particularly for the horizontal portion of the curves, said to represent Kick&apos;s laws. That the milling; grinding, and turning data obtained by Walker and Shaw for both metals and minerals happen to comply with. certain interpretations of these two theories under certain specialized conditions

Jan 1, 1955

By G. V. Sullivan, B. E. Davis, T. O. Llewellyn

The Bureau of Mines, US Department of the Interior, conducted studies to recover phosphate from four dolomitic southern Florida deposits not currently mined. The samples contained 5.8-10.2% P205 and 1.7-4.8% MgO. Chemical analyses of sized fractions indicated that no pebble concentrate, +1.2 mm (+14 mesh) could be produced from these samples. A scheme was developed that consisted of desliming, grinding, scrubbing, and redesliming the ore to produce a flotation feed. Conventional one-step fatty acid fuel oil batch flotation tests on the samples resulted in concentrates containing 29.0-31.3% P205 at flotation recoveries ranging from 72.4 to 96.1% of the flotation feed. The MgO content of the concentrates ranged from 0.47 to 1.36%. Continuous flotation of the Manatee No. 2 sample indicated that commercial-grade phosphate concentrates analyzing 31.3% P205 and 0.55% MgO could be produced with a flotation recovery of 89.9%. The MgO content of concentrates obtained from the Manatee No. 1 and Hardee samples was 1.20 -1.36 %, respectively. Leaching with aqueous SO2 reduced the MgO content of these phosphate concentrates to 0.5 and 0.8%, but with a concomitant loss in phosphate recovery of about 10%.

Jan 1, 1985