Search Documents

By J. Steininger

The Hallimond tube flotation of sphalerite and pyrite with sulfhydryl collectors has been found to be inhibited near neutral pH in the presence of copper salts. Alkalimetric titration studies of the reactions between collector and activator indicate that this effect is apparently related to the formation of basic copper collector complexes. The conditions of formation of these compounds and their stability are in good agreement with the depression observed in flotation experiments. The general procedure employed in the flotation of zinc sulfide minerals requires activation of the mineral surface by heavy metal ions, usually copper, which react more easily than zinc with the common short-chain ionic sulfhydryl collectors.' Commercially, zinc flotation is carried out under alkaline conditions (pH 7 to 10.5), but small-scale experiments indicate that zinc sulfide minerals can also be activated and collected under acid conditions. Selectivity, however, becomes poor at low pH and undesirable materials such as pyrite, silicates and carbonates tend to report in the float. Several years ago, Wark and Sutherland~, measured the contact angles of air bubbles on copper-activated sphalerite immersed in various sulfhydryl collector solutions. When represented, as in Fig. 1, on pH-sodium cyanide diagrams, the results are characterized by 'islands' of non-contact near neutral pH and

Jan 1, 1969

By N. V. Hansell

l. INTRODUCTION. THE last few years have shown an increasing interest in the subject of beneficiating iron-ores -in all iron-producing countries. In the United States, this movement has been slower than in certain parts of Europe, for the obvious reason that the abundance and relative cheapness of the Lake Superior iron ores has hindered the development of enterprises for the preparation of low-grade ores. Gradually, however, conditions have changed. The world's consumption of iron is increasing enormously. Being in 1900 about 40,000,000 tons, in 1910 ii was already 60,000000; and there is no reason to doubt that for the near future the increase in iron-consumption will continue at the same rapid rate, especially with, the development of China, certain parts of Africa, and other regions which have hardly been touched as yet by modern industrialism. It is. therefore, not surprising that apprehension is felt that the known available iron-ore resources of the world are gradually being depleted. Signs of this feeling are the recent investigation, under the direction of the U. S. Geological Survey, of the iron-ore resources of the United States, and the estimate presented to the last International Geological Congress, at Stockholm, Sweden, of the iron-ore resources of the world. These investigations have emphasized the fact that the known high-grade ore-deposits are limited in extent, and will, at a not distant future, be exhausted, compelling the iron industry to depend for raw material on the enormous deposits of low-grade ores which are distributed over almost all the world. The discovery of new deposits of high-grade ore, in countries not yet thoroughly explored, will not materially change this prospect. Of course, the part which such new deposits will play in the future cannot be forecast. The difficulty and cost of transportation will probably exclude many of them from use at the present centers of the iron industry.

May 1, 1912

By G. H. BUCHANAN

ALTHOUGH the nomenclature of the chemical tools of flotation is probably familiar to you, it will do no harm to review it; . In order to make the terms more real I have employed an illustration which likens flotation to an old-fashioned balloon ascension, such as we witnessed in boyhood at the county fair. The mineral to be floated is the aeronaut, conspicuous in his gilt-spangled tights, who is to be separated from you and me and the other small boys who are standing about, said boys being the g-a-n-g-u-e, or g-a-n-g, as we would have spelled it. The oil film surrounding the bubble is the counterpart of the silken fabric of the balloon, and bubble and balloon will rise for. the same reason, namely. that the fluid outside it is heavier than the fluid within. In flotation reagent nomenclature the material of which the bubble is made is called the "frother.",

Jan 1, 1930

By C. A. Heiland

NOT only has the demonstration of progress in all fields of science been characteristic of the Chicago "Century of Progress," but the manner in which the fundamentals of these sciences have been displayed captivated the visitor's eye and ear at the same time. The average individual is interested most in progress which concerns his every-day life. He is fairly well educated in medicine, biology and certain aspects of physics. But how raw materials and chiefly minerals occur, how they are located, taken out of the ground and refined, is something which appears to be more remote from the every-day line of interest, and about which, therefore, the public knows comparatively little. This is particularly true of the oil industry, although it ranks in size second only to agriculture in the United States. In appreciation of the tremendous educational value which a complete exhibit on all phases of the mineral industries would have, both mining and metallurgical as well as oil inter¬ests took steps early to make these exhibits at Chicago a reality. The board of directors of the A. I. M. E. authorized an advisory committee to the Museum of Science and Industry early in 1932. It is divided into four subcommittees - for geology and petroleum, for metal mining, for coal mining, and for metallurgy respectively. The entire committee held its first meeting in Chicago on April 11 and 12, 1932, to advise with the Museum's officials and experts about the most advantageous arrangement of the minerals industries' and geology exhibits.

Jan 1, 1933

By C. W. MacGregor

IN the testing of materials there exist various methods of recording graphically the behavior of a material subjected to tensile stress. Prob-ably the most common method is to plot the tensile stress So, obtained by dividing the load P by the original area of cross section AO at the start of the test, as a function of the strain ?o, which is obtained by dividing the ?Lo or the change in the gauge length by the original gauge length Lo. A list of the symbols used here is given in Table 1. This method, while it has proved useful in the routine testing and comparison of various materials, does not have a very sound physical basis, as was first pointed out by P. Ludwik1, and consequently does not afford a very deep insight into the true physical behavior of the material under stress. Among the objections to this method may be mentioned: (1) that by dividing the load P at any stage of the test by the original area Ao a fictitious stress is obtained, which does not actually exist; (2) that the strain ?o = ?Lo /Lo is not an exact expression for the true strain for large values of ?Lo in per cent of Lo; (3) that when necking starts the strain varies considerably along the gauge length and the above expression no longer gives the true strain existing at any point on the outside of the bar; and (4) that the axial strain varies over the cross section of the necked portion and ?o does not represent an average of these strains over the cross section. Stresses taken from such a diagram would be only approximate and, if used to compare results of a test on a given material under simple tension with results obtained under combined stresses, certain errors would he thus introduced. In order to overcome some of these objections, various methods have been suggested, both as to the quantities to be measured and as to their graphical representation. In some cases the so-called "true stress," obtained by dividing the load P by the actual area of cross section A existing when the load P was applied, is plotted as a function of the strain

Jan 1, 1937

By Goodman, Richard E.

A complete rational analysis for design of excavation slopes and loaded rock masses is a desirable but perhaps unattainable goal. Irregular external and internal boundary conditions, poor understanding of failure criteria for large masses of rock, capricious material properties, and the importance of indeterminate forces and inaccessible and virtually un- sampleable rock defects emphasize the importance of experience in this aspect of rock engineering. The experience must be correlated with geological factors. In certain regions the accumulation of such experience through the observation of existing rock slopes in various formations constitutes an important aspect of studies for design of rock excavations.

Jan 1, 1969

By GEORGE A. KIERSCH

The awesome destructive power of known and projected weapons of war presages a new need for geologists and engineers, who may be called upon to locate vital industry underground, thereby protecting it from sky-borne destruction. The Corps of Engineers is now conducting special tests to establish design standards covering the general field of underground installations as well as surveys a of construction methods and the operational hazards connected with such plants. National planning must dictate a policy that is either tactical, where surface manufactured parts; are stored underground and during art emergency assembled, or operational with both the manufacturing and assemblage completed in subsurface plants. Both plans of operation require the use of subterranean plants. Relocation of vital plants underground will probably involve only a small percentage of the production capacity of this nation. The cost of rebuilding in new location will obviously limit its adoption

Jan 1, 1949

By E. P. Fleming

COMPARED to the situation abroad, the domestic industry continues to lag both as regards the production and consumption of newly mined lead. During 1938 we produced and consumed slightly over 20 per cent of the world output, whereas ten years ago the figure was nearly double this pro- portion. Labor difficulties and absence of demand were chiefly responsible for the general inactivity. In the foreign field, in spite of low metal prices, production and consumption of lead equaled or exceeded all previous records. Practically all the large companies, with the exception of those in Spain, increased operations, though it should be noted that the foreign lead mines have higher-grade ores than domestic mines. In view of the rapid expansion of the foreign industry, it is natural to expect greater progress abroad, particularly in process metallurgy.

Jan 1, 1939

By AIME AIME

COMMITTEES. LOCAL COMMITTEE.-R. C. Crawford, Chairman; Harrison W. Craver, Secretary; Julian Kennedy, Taylor Allderdice, E. W. Pargny, Charles L. Miller, W. H. Rea, S. A. Taylor, M. E. Wadsworth, W. A1. Henderon, A. C. Dinkey, W. L, Jones, E. L. Messier, George Mesta, J. H. Jones, G. H. Riley, S. L. Goodale, D. W. McNaugher. LADIES' COMMITTEE.-Mrs. Taylor Allderdice, Chairman; Mrs. Julian Kennedy, Mr. R. C. Crawford, Mrs. E. M. Herr, Airs. J. W. Marsh, Mrs. T. A. Mellon, Mrs. G. P. Bassett, Jr., Airs. D. M. Clemson, Mr. Charles L. Miller, Mrs. V. L. P. Shriver, Mrs. W. A. Bostwick, Mrs. A. C.. Dinkey, Mrs. A. P. Childs, Jr., Mrs. F. R. Dravo, Mrs. Hermon Griffin, Mrs. W. H. Nimmick, Mrs. F. H. Lloyd, Mrs. S. G. Cooper, Mrs. S. H. Church, Mrs. E. N. Ohl. The Institute Headquarters was established at the Hotel Schenley, where a bureau of information was maintained for the benefit of the visiting members and guests of the party during the time of the meeting. TECHNICAL SESSIONS. The first session, held Tuesday evening, Mar. 1, 1910, in the large lecture hall of the Carnegie Institute, was called to order by Harrison W. Craver, Secretary of the Local Committee. Mr. Craver introduced Dr. John A. Brashear, who extended to the members and guests a hearty welcome to the city of Pittsburg, to which David W. Brunton, President of the Institute, responded. The following papers were presented in oral abstract by the authors: Biographical Notice of Dr. Charles B. Dudley, by Dr. R. W. Raymond, New York, N. Y. Biographical Notice of William Metcalf, by Col. II. P. Bope, Pittsburg, Pa. Development of Hindered Settling Apparatus, by Robert H. Richards, Boston, Mass. (Illustrated by lantern-slides.) A Few Mining Districts in the Argentine Republic, South America, by Z. S. Beyl. (Illustrated by lantern. slides.)

Apr 1, 1910

By M. A. Grossmann

THE hardenability of most steels can be predicted within 10 to 15 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as-quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a ''pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain sue may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter"; namely, the diameter of bar, in inches, that will just harden all the way through (absence of un- hardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test. The data bring out certain features rather clearly. For example: I. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals," are known; thus an "incidental" chromium content of 0.20 per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybde- num when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful as wouldappear to be common experience; observe that an increase from no manganese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.20 per cent Mo provides a factor of 1.63, an increase of over 60 per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added " 20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the first small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater hardenability will be obtained by using, for example, 0.5 per cent of each than by using 1.0 per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost lo per cent in hardenability (in these units); this, however, does not apply to certain steels of high hardenability. It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome- molybdenum and chrome-vanadium steels, undissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum possible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the absence of Cr, and V up to 0.04 per cent), the charts provide reasonable approximations. The precise figures on the charts are suggested as tentative, subject to some modification as more data accumulate, but the fundamental concept appears to be supported by tests made on a wide variety of steels, a few of the correlations being shown in Fig. I.

Jan 1, 1942

By M. A. Grossman

THE hardenability of most steels can be predicted within 10 to 15 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a "pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain size may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter"; namely, the diameter of bar, in inches, that will just harden all the way through (absence of unhardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test. The data bring out certain features rather clearly. For example: I. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals," are known; thus an "incidental" chromium content of o.-2o per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybdenum when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful as would appear to be common experience; observe that an increase from no manganese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.2o per cent Mo provides a factor of 1.63, an increase of over 6o per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added "20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the first small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater harden ability will be obtained by using, for example, o.5 per cent of each than by using 1.0 per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost 10 per cent in hardenability (in these units); this, however, does not apply to certain steels of high hardenability. It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome-molybdenum and chrome-vanadium steels, undissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum possible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the absence of Cr, and V up to 0.04 per cent), the charts provide reasonable approximations. The precise figures on the charts are suggested as tentative, subject to some modification as more data accumulate, but the fundamental concept appears to be supported by tests made on a wide variety of steels, a few of the correlations being shown in Fig. I.

Jan 1, 1942

By D. E. Wolfson, D. A. Reynolds, F. W. Smith

IN 1948 the U. S. Bureau of Mines began a three-phase program to evaluate the extent and quality of U. S. coking coal: 1) a factual appraisal of known recoverable reserves in beds of mineable thickness, 2) a study of preparation characteristics, and 3) a study of carbonization properties. A previous paper presented the methods used in assessing reserves.' Although this investigation is only partly completed, data on coking properties of the Pittsburgh district coals are now available. The results are presented in this article. When coals are selected for manufacture of metallurgical coke more factors must be considered than for any other major use, as no basic industry requires coal of such high quality and uniformity. This is particularly true in the Pittsburgh district, where blast furnace practice is based on use of cokes from high quality coals. Although it is true that inferior coals are carbonized in other industrial areas, both here and abroad, the Pittsburgh coals are the best economically obtainable in the required tonnages, even though they are not the most desirable for metallurgical use. In the general evaluation of suitability of coals for coke making, particular attention is given to: 1) reserve, 2) ash and sulfur content, 3) inherent properties of forming strong, well fused coke, 4) expanding characteristics, and 5) blending properties. Items 1 and 2 are covered in detail in the first two phases of the survey, and coking behavior is considered in items 3 through 5. Problems is Coal Evaluation: Although not all coal beds of immediate or potential use to the coking industry in the Pittsburgh area have been tested for their coking properties, enough tests have been made to permit certain generalized statements. Virtually all the coals that will be used in this district are from the Appalachian region, and except for high oxygen coals from outcrops or stripping operations, they are coking coals. Hence the evaluation problem is not so much that of distinguishing between coking and noncoking coals as attempting to measure quantitatively differences in the coking and expanding properties of the better coking coals. Quantitative differentiation between good coking coals, is complex, since differences in their coking abilities are frequently of about the same magnitude as the precision of the test. Small-scale tests are generally unsuitable for measuring these slight differences, and there has been gradual acceptance of pilot-scale tests. Test Methods Employed: All the data reported here were obtained in two units known as the Bureau of Mines-American Gas Association (BM-AGA) carbonization apparatus and the sole-heated expansion oven. The BM-AGA unit, which consists essentially of a cylindrical steel retort about 18 in. diam and 26 in. high, carbonizes enough coal (180 lb) to allow evaluation of the coke by standard methods of the American Society for Testing Materials. The BM-AGA carbonization procedure and methods of testing the gas, liquid, and solid products have been described.' Expanding characteristics of the coals were determined in the sole-heated expansion oven," wherein the coal charge, heated from the bottom only, is carbonized under a constant applied force and the linear expansion or contraction is measured. Although results in this oven have never been quantitatively correlated with the expansion behavior of coals in conventional slot ovens, they are useful in assessing expansion behavior. In this report discussion will be confined to results obtained from these pilot-scale units, although the following data are available for most coals: proximate and ultimate analyses, free swelling index, agglutinating value, and plasticity. Sources of Coals Tested: In selection of coals for coke manufacture, economic considerations are as important as quality, and each coke plant balances these two factors to meet requirements of the most satisfactory coke at lowest price. Although these economic factors may in some instances outbalance small differences in coke quality, they are usually specific to each coke plant and cannot be given in any general statement. Recognizing that coal and plant operating costs are beyond the scope of the survey, the USBM evaluates the coking quality of various coals without regard to their competitive economic status. For the purpose of this article, coals of interest to the Pittsburgh district are arbitrarily defined as

Jan 1, 1958

By George Krauss, M. Cohen

The reverse martensitic transfomzation (i.e., the conversion of martensite to austenite on heating) was investigated in Fe-Ni alloys containing 30.5 to 33.5 wt pct Ni. The reversed austenite was found to be sufficiently distorted to exhibit marked differences in mechanical properties and to undergo recovery and re crystallization on further heating. In particular, the yield strength of the reversed austenite was as much as 2.5 times higher than that of the virgin austenite: with five cycles of the direct and reverse martensitic transformation, the yield strength was 2.6 times higher. There was an accompanying decrease in strain-hardening capacity and in stable ductility or uniform elongation. The recrystallization was observed to follow sigmoidal kinetics, but was characterized by an abnormal1y large temperature dependence which was evidently due to carbon segregation at the migrating grain boundaries. Upon recrystallization, the strength Properties reverted to those of the virgin austenite, but the ductility did not fully recover until the annealing temperature was further raised to dissipate the carbon segregation at the grain boundaries. The transformation of reversed austenite to produce second-generation martensite resulted in an unusually imperfect structure, thereby leaditg to additional strengthening. Horlleuer, the martensitic phase was much less responsive in this respect than was the austenite. MOST martensitic transformations are capable of undergoing a reverse transformation back to the austenitic phase on heating.&apos; This reaction, like the direct transformation to martensite on cooling, is usually athermal. In analogy with the Ms andMf temperatures for the martensitic transformation (where M, > Mf), the reverse transformation is characterized by the As andAf temperatures (where As<Af). It is well-known that the finish (Af) of the martensite-to-austenite reaction on heating may occur at a temperature where austenite is not stable relative to other phases in the equilibrium diagram.&apos; Reverse martensitic transformations have been found to influence the properties of the parent austenitic phase in a number of ferrous alloys. The austenite thus produced after one or more reversals is significantly altered in strength, microstruc-ture, diffusivity, and annealing characteristics compared to well-annealed, virgin austenite. The first detailed observations of such phenomena were made by Wasserman3 on an Fe-30 wt pct alloy. He found that the reversed austenite (i.e., austenite formed by the reverse martensitic transformation) was much stronger than the original austenite, and the second-generation martensite (i.e., martensite produced from the reversed austenite) was somewhat stronger than the first-generation martensite. On heating the reversed austenite, recrystallization occurred in a manner similar to that of a cold-worked metal; the Laue spots sharpened and the strength decreased.4 In recent years, Russian workers have shown considerable interest in these reverse martensitic transformations. Most of such investigations5-10 have been concerned with the stabilization of reversed austenite relative to subsequent martensitic transformation, and because of its unusual nature, this phenomenon will be discussed in detail elsewhere." On the other hand, the annealing behavior of reversed austenite and the attendant variation in properties have received little attention beyond the experiments of Wasserman.3,4 Gridnev eta1.,8 in one of the few such studies. followed the hardness change of reversed austenite as a function of time at three annealing temperatures. The marked strengthening of austenite achieved by the reverse martensitic transformation has been referred to as "transformation strengthening" by Wasserman3,4 and as "phase hardening" by Malyshev et a1.7,9,10 to differentiate it from hardening produced by cold working. Both groups of investigators noted that further strengthening of the austenite could be attained by repeated or cyclic transformations, but the first cycle resulted in the most pronounced effect. Evidence of the altered microstructure of reversed austenite has been reported by Maximova and Nikonorova6 and by Edmonson and KO.12 The former found that reversed austenite was much more sensitive to etching than the original austenite, and the latter authors observed a (&apos;ghost" structure resembling martensite in certain areas of the reversed austenite. Enhancement of the self-diffusion rate in reversed

Jan 1, 1962

By C. H. Keplinger

WARTIME factors have strengthened the production engineering consciousness of the petroleum industry. The basic principles of sound oil-production technology have been accepted as the standard by the industry and the governmental co-ordinating agencies. Every effort is being made to furnish larger quantities of petroleum with a minimum expenditure of materials and under strict conservation practices. The sphere of influence of production engineering extends from fundamental reservoir control of withdrawal rates and reservoir pressures to bolstering production from stripper wells. Serious transportation difficulties in moving oil to the East Coast have stimulated secondary recovery operations in the Appalachian and East Central oil-producing states. Diminishing discovery of new oil reserves by exploration activities increases the importance of promoting efficient oil-producing methods and practices throughout all productive areas in the United Nations.

Jan 1, 1943

By E. D. Gardner

AGAIN in 1945, the fourth year of World War 11, the American mining industry met the necessary demand made upon it for metals. Lack of labor prevented full production in some districts; maximum output, however, was maintained with the man power available. Development work and maintenance of mechanical equipment were neglected in favor of immediate production. Drafting of the younger men continued throughout the year, and the loss of personnel to war industries with higher wage rates continued up to "V-J" Day, Aug. 14. Labor shortages were more critical in 1945 than in 1944 though the man-power situation eased for some districts in the last quarter of the year. The trend in mining for the most part was to increase tons per man-shift by continued increased mechanization and refinements in methods and practices; larger equipment was installed where practicable. Labor shortages, together with the current higher wage rates, have advanced mechanization several years ahead of normal progress. The manpower shortage and the employment of inexperienced men had the effect of decreasing the average efficiency of the individual workman, but this condition was largely balanced by improved organization, greater efforts to improve labor relationship, and increased use of incentive pay systems. Safety instruction was emphasized, personnel contacts were increased, and more frequent foremen meetings were held to clarify contract agreements. Many of the large companies maintained schools to train green workmen.

Jan 1, 1946

By R. M. Genevray, M. B. Bever, E. J. Suoninen

THE martensitic transformation in the ß-phase of the Cu-Zn system has been the subject of several investigations. The transformation is known to be reversible and to be affected by stress. Its temperature range has been determined as a function of composition. In the investigation reported here, the effect of tensile stresses on the transformation was investigated quantitatively. Some information was also obtained on the thermoelastic behavior of the martensite formed in the first stages of the transformation. Most of the experiments were done with alloy E of an earlier investigation;&apos; this alloy analyzed 60.49 pct Cu and 39.51 pet Zn by weight. The methods of shaping and heat treatment were also essentially the same as those previously used. The stress was applied to the specimen immersed in a cooling liquid. The transformation was followed by measuring the electrical resistance with a Kelvin bridge and the elongation with a cathetometer. Fig. 1 shows the M, temperature as a function of stress. Resistance and strain measurements gave essentially identical values. The results suggest a roughly linear relation between M. and in the range investigated, up to 12 kg s mm". At higher stresses, plastic deformation begins to interfere seriously with this relationship. The increase of M, with stress is consistent with published work on the effect of stress on the martensitic transformation. The slope of the curve, 4°C per kg mm ", is of the same order of magnitude as the corresponding value calculated for steel.&apos; Fig. 1 also shows the difference, AM, between the temperature of 50 pct transformation on cooling, as measured by changes in length, and that of 50 pct reverse transformation on heating. This difference, which may be considered a measure of the hysteresis, increases with stress; the decrease at highest stresses is probably associated with plastic deformation. Preliminary work using only resistance measurements was done with an alloy containing 60.15 pct Cu and 39.79 pct Zn by weight. The results indicated higher values o-F M, in agreement with the known variation of M. with composition.&apos; The effect of stress on M, (2°C per kg mm-&apos;) was of the same order of magnitude as that shown in Fig. 1 for composition E. An increase in hysteresis with stress was also found. The following experiment was made in order to investigate a partially transformed structure. A specimen of alloy E was cooled to — 85°C under a stress of 4.7 kg mm-&apos;. Under these conditions, the martensitic transformation started but did not go to completion. The stress was then released and the specimen cooled to — 105°C. Fig. 2 shows the measured elongation c. The first change in the slope of the curve indicates the beginning of the transformation under stress. Removing the load at —85°C caused a decrease in length to the value corresponding to the elastic elongation of the parent phase resulting from the applied stress. Hence, the marten-site formed in the first part of the experiment apparently disappears completely and without hysteresis upon the release of the stress. The increase in length on further cooling indicates renewed formation of martensite. These conclusions are consistent with the concept of "thermoelastic" martensite," which has been confirmed by test." Acknowledgments The authors are greatly indebted to Professor M. Cohen for his advice and encouragement. They also thank F. Paxton for assistance. Thanks are due the American Brass Co. which supplied the alloys. References E. Kaminsky and G. V. Kurdjumov: Zhur. Tekhn. Fiziki SSSR (1936) 6, p. 984. A. B. Greninger and V. G. Mooradian: Trans. AIME (1938) 128, p. 337. "J. E. Reynolds, Jr. and M. B. Bever: Trans. AIME (1952) 194, p. 1065; Journal of Metals (October 1952). &apos;A. L. Titchener and M. B. Bever: Trai~s. AIME (1954) 200, p. 303; Journal of Metals (February 1954). " 3. A. Kulin, M. Cohen, and B. L. Averbach: Trans. AIME (1952) 194. p. 661; Journal of Metals (June 1952). "J. K. Pate1 and M. Cohen: Acta Metallurgica (1953) 1, p. 531. &apos;C. Crussard: Comptes Rendus (1953) 237, p. 1709. &apos; G. V. Kurdjumov: Zhur. Tekhn. Fiziki SSSR (1948) 18, p. 999. G. V. Kurdjumov and L. G. Khandros: Dokl Akad. Nouk. SSSR (1949) 66. p. 211.

Jan 1, 1957

By Jack M. Swales

Kermac Potash Co., the newest American entry in a rapidly expanding industry, has come on the scene with notable variations in conventional shaft-sinking and mining techniques. Located in the famed potash producing district east of Carlsbad, N. Mex., Kermac started up its mine in November, 1965, to supply ore to the company&apos;s 500,000-tpy potash crystallization refinery. In so doing, the company (1) drilled the first large diameter mine shaft in the potash industry and (2) has employed new continuous miners especially adapted for use in thin potash beds. REACHING THE ORE ZONE In its initial mine planning, Kermac, a partnership owned jointly by Kerr-McGee Corp. and the National Farmers Union Development Corp., considered it imperative that the shafts be sunk and equipped as soon as possible and that the mine be developed sufficiently to insure a constant ore feed to the mill when the unit was placed on stream. After examining the alternative sinking techniques available to it, the company decided to accept a proposal by Big Hole Drillers, Inc., to drill the shaft from the surface through various formations of sandstones, siltstone, shales, anhydrite, limestones, dolomite and salts to the potash ore zone.

Jan 12, 1966

EXECUTIVE COMMITTEES OF LOCAL SECTIONS Arizona E. P. MATHEWSON, Chairman W. V. DECAMP, First Vice-chairman F. W. MACLENNAN, Second Vice-chairman E. D. GARDNER, Secretary-Treasurer, U. S. Bureau Of Mines, Tucson, Ariz. MICHAEL CURLEY J. P. HODGSON HENRY F.1 ASTER CLYDE E. WEED Boston Meets first Monday each winter month GEORGE A. PACKARD, Chairman FRANKLIN B. RICHARDS, Vice-chairman F. LEROY FOSTER, Secretary-Treasurer Rooms 8-219 Mass. Inst. of Tech., Cambridge, Mass. G. W. METCALFE D. H. MCLAUGHLIN

Jan 1, 1932

By Tenney, J. B.

DEVELOPMENT of complex ores in the south- western part of the Rocky Mountain region has been retarded by the prohibitive distance to the nearest suitable zinc treatment plants. In the north- western and central Rocky Mountains the building, cluring tlie past decade, of electrolytic zinc plants at Anaconda, Great Falls, Trail, and Burke has tremendously stimulated the mining and exploiting of such .ores, greatly increasing the production of lead, zinc, copper, gold, and silver. Selective flotation permits the making of high-grade led, copper, and zinc concentrates. If the zinc concentrates could be made free from lead, copper, gold, and silver, they could be shipped economically to Mid- Western retort plants designed for such concentrates. Unfortunately a considerable proportion of the precious metal content accompanies the zinc blende in the ores of this region. Although some of it is saved in &apos;retort residues, the treatment cost is thereby increased so materially and the proportion saved so small, that .concentrates of ordinary grade cannot stand treatment charges and freight.

Sep 1, 1928

By Henry S. Munroe

THE earliest accounts we have of Japan represent the country as having great mineral wealth, especially of precious and useful metals. Marco Polo, the Venetian traveller, in the thirteenth century, writes of "Zipangu:” "They have gold in greatest abundance, its sources being inexhaustible. The king does not allow of its being exported. To this circumstance we are to attribute the extraordinary richness of the sovereign&apos;s palace. The entire roof is covered with a plating of gold. . . . The ceilings of the halls are of the same precious metal ; many of the apartments have tables of pure gold of considerable thickness, and the windows also have golden ornaments." Marco Polo also gives an account of an unsuccessful Tartar expedition against Japan, prompted by the supposed great wealth of the country. Columbus also, as well as many other explorers, were attracted and encouraged by these prevalent reports of the wealth of the islands of Zipangu. Kaempfer, writing in 1727, speaks of the great mineral wealth of Japan, and especially of the abundance of gold, which, he says, is found in many provinces. The Portuguese and Dutch, while they had trading-posts in Japan, furnished tangible evidence of the truth of the early reports. Between 1550 and 1639 the Portuguese merchants sent home from Japan nearly three hundred million dollars&apos; worth of bullion, most of which was gold. As the relative value of equal weights of gold and silver was then six to one, while in Europe, at the same time, it was nearly twelve to one, the exchange of silver bullion for gold was by no means an unimportant part of their business. After the Portuguese, the Dutch continued the exportation of bullion, and the exchange of silver for gold, though with less profit, as the relative value of gold increased with the demand. Between 1649 and 1671 the Dutch traders sent home over two hundred million dollars in bullion, of which, however, nearly two-thirds was silver. In 1671 the Japanese government, alarmed at the rapid rate at which the precious metals were leaving the country, issued an edict forbidding the exportation of gold or silver, under heavy penalties, which had the immediate effect of stopping this trade. Besides bullion, copper formed at this time a most important article of export. According to Dr. Geerts,* who has examined the old * Transactions Asiatic Society of Japan, vol. iii, p. 41.

Jan 1, 1877