Search Documents

By N. O. Taylor

THE failure, by swelling, of several cast aluminum-zinc, spiral, pump rods, used to circulate water in a constant-temperature bath, brought up the question as to whether the presence of tin in varying quantities would have any appreciable influence in controlling this action. Previous workers had found the same difficulty with aluminum-zinc alloys, due to their swelling in water or solutions of electrolyte^.^ It was known that pure aluminum was practically insoluble in concentrated sulfuric and nitric acids, presumably due to the formation of an oxidized film on the surface. Concentrated sulfuric acid had little or no effect on pure zinc and tin and concentrated hydrochloric acid would attack all three metals. These facts aroused curiosity as to the probable reaction of the ternary alloys of these metals, and tests were made to determine their resistivity to the action of common laboratory reagents. Samples, covering the entire range of the ternary series of aluminum, zinc and tin alloys, were made up from good grades of the commercial metals.2 The materials were melted, at as low temperatures as possible, in graphite crucibles in a gas-fired crucible furnace. Graphite crucibles were used in preference to clay, to prevent the absorption of silicon by the aluminum, as found by previous workers. The melted materials were stirred thoroughly with pine sticks in order to ensure complete mixing and the greatest possible freedom from oxidation, and were cast in sectional, iron molds giving bars % in. in diameter and 5 in. long.

Jan 1, 1927

By J. D. Livingston, H. E. Cline

The lamellar-dendritic transition in Sn-Pb alloys near the eutectic composition has been studied at high growth rates. Lamellar structures were found over a substantial range of tin-rich compositions, and this range extended to increasingly tin-rich concentrations as growth rate increased. These results are discussed in terms of stability and competitive-growth arguments. Various experimental and structural limitations to the rate of directional solidification are discussed. The rate of heat removal at the heat sink is the major experimental limitation. ReCENT interet1,2 in the use of fine composite structures produced by directional solidification of eutectic alloys makes it important to determine the range of composition and growth conditions that yield such microstructures. Because increasing growth velocities produce increasingly finer microstructures, it is particularly significant to determine the factors limiting the rate of solidification. Mollard and Flemings3 have shown that composite structures, free of primary dendrites, can be obtained in Sn-Pb alloys of off-eutectic composition. The composition range of composite structures was found to increase with increasing values of G/V, where G is the temperature gradient and V is the growth velocity. These results are in good quantitative agreement with an analysis of the stability of a planar eutectic interface.4 This analysis specifically predicts that over a small range of compositions stable lamellar structures will be obtained even for G/V = 0, hence, even at very high growth rates. The lamellar-dendritic transition in Sn-Pb alloys has also been analyzed with a model based on competitive growth between dendrites and the composite structure.576 This treatment, based on earlier work on organic eutetics,7 predicts that the composition range yielding composite structures in Sn-Pb will increase rapidly at high growth rates. An increase in the composition range of composite structures at high growth rates was recently observed in Cu-Pb alloys near the monotectic composition.8 In view of these results, and the predictions of the stability and competitivegrowth analyses, it was decided to study the lamellar-dendritic transition in Sn-Pb alloys at high growth rates. EXPERIMENTAL Using 99.999 pct pure materials, a series of Sn-Pb alloys were prepared containing 16.8 at. pct to 27.6 at. pct lead. (Eutectic composition is 26.1 at. pct Pb.) Ingots were extruded to 0.175 in. rod, and some rod was drawn to 0.070-in. wire. Directional solidification was accomplished in two different ways, Fig. 1. For growth rates up to 2 x 10-1 cm per sec, a 0.175 in. diam sample was placed in a graphite crucible 5 in. long with 0.250 in. OD and 0.035 in. walls. Samples were melted under flowing argon in a vertical, platinum-wound furnace, and solidified by driving the crucible downwards through a \ in. hole in a water-cooled copper toroid, Fig. l(a). An insulated chromel-alumel thermocouple was imbedded in the center of a representative sample, and moved with the sample during solidification. The local temperature is plotted against the distance travelled by the sample in Fig. 2. As the growth rate increased, the solid-liquid interface moved closer to the water-cooled toroid and the temperature gradient increased. At growth rates above 10-1' cm per sec, heat was not removed fast enough and the sample moved into the toroid in the liquid state. The curve for V = 2 x 10-1 cm per sec shows a plateau caused by incomplete removal of latent heat from the interface, a problem which will be discussed later. To improve the heat removal, the toroid was cooled by nitrogen gas precooled in liquid nitrogen. This allowed successful solidification at rates up to 2 x 10-1cm per sec. Higher solidification rates required still more effective heat removal. Samples 0.070 in. in diam were placed in graphite tubes 0.125 in. in diam with 0.020 in. walls. Instead of cooling by sliding contact with a cooled toroid, these thinner samples were sprayed or directly immersed into water, Fig. l(b). After solidification, samples were stored in liquid nitrogen until they could be examined metallographic-ally. The surface was prepared with a diamond-knife microtome, followed by a light etch. The presence or absence of tin dendrites, Fig. 3, or lead dendrites, Fig. 4, was noted by optical microscopy, usually of a transverse section near the center of the sample. Replicas of the surface were prepared and examined in an electron microscope to resolve the fine lamellar structures, Fig. 5. The structures observed at various compositions and growth rates are summarized in Fig. 6. Composite structures were observed at increasingly cin-rich compositions as growth rate increased. This transition from dendritic to composite structure with increasing growth rate was also demonstrated by solidifying half a sample at a slow rate and then suddenly increasing the growth rate by lifting the furnace and quenching the sample with a water spray. A longitudinal section of this sample, Fig. 7, shows that the tin dendrites, which extended ahead of the slow-moving composite interface, were bypassed by the composite when the growth rate was increased. The range of composite structures at high growth rates was limited by the appearance of primary lead dendrites on the tin-rich side of the eutectic composition. Observation of representative longitudinal

Jan 1, 1970

By Harold Markus, Gerhard Derge

THE first paper1 of this series described a technique of careful surface preparation by means of which reproducible results may be obtained from potential measurements of the behavior of tin in carbonate solutions with a pH range from 8.4 to 11.2. It then went on to establish the behavior of pure tin electrodes under these conditions and showed that the metal remains active at all times, though the steady potential attained after several hours decreases from I.I2[t] volts at a pH of 12.6 to 0.6 volts at a pH of 8.4. This behavior may serve as a norm with which all other data can be compared. In the second paper,2 small amounts of other anions were added to the carbonate solutions and the conclusion was reached that the common impurities encountered in alkaline materials packaged in tin do not increase corrosion. In fact, in some cases these anions may actually promote the formation of protective films. The present paper rounds out this survey by presenting data on the influence of cations added to the carbonate solutions, as well as the effect of alloy additions to the tin. In many cases the potential data are supplemented with weight-loss measurements. Information is also presented on the effects of some additional anions, the influence of gases above the electrolyte, the behavior of high-purity tin, and the effect of atmospheric oxidation on the corrosion resistance of the above-named alloys. Analysis of the entire body of data discloses some general rules applicable to corrosion in carbonate solutions. The experimental methods used are the same as those previously described. EXPERIMENTAL DATA Cations.-The carbonates of the cations K+, Li+, NH4+, which are soluble, were studied in the same way as the anions, by adding 0.01 mol of the metal carbonate to one liter of 0.2 M sodium carbonate solution, pH 11.2, or to 0.1 M sodium bicarbonate, pH 8.4. The other metallic carbonates are only slightly soluble, of the order of 0 7-3 mols per liter or less, and the sodium carbonate solutions were saturated by adding excess reagent several days before the experiment, shaking frequently, and filtering just before use. The chemicals were c.p. grade in each case except the indium salt. This salt was prepared by solution of the metal in hydrochloric acid and precipitation by addition of Na2CO3. These cations may be divided into two classes, according to their effect on the potential behavior of the tin: (I) normal, (2) passive. To offer a basis of comparison, curves I of Figs. I and 2 are given to illustrate the behavior of tin in carbonate solutions saturated with CaCO3. These curves are the

Jan 1, 1941

By Roman Y. Poderny, Vladimir V. Rjevskii

In the USSR, the Moscow Institute of Radio Electronics tronics and Mining Electro-Mechanics (MIRGEM) has started what it hopes will become a nationwide movement to educate mining students in the precise specialties that industry has come to require. Courses for mining engineers, the MIRGEM faculty proposes, should dovetail as exactly as possible with specific jobs available in the mining profession. Acting upon this thesis, MIRGEM revised its own curriculum in 1962 and has since presented an over-all plan for Soviet mining education before two mining school conferences as well as the Ministry of Higher Education and a number of major Soviet industrial ministries. The plan was universally approved with some suggested revisions. SOVIET MINING EDUCATION TODAY At present, mining education in the Soviet Union covers the exploitation of solid minerals and raw materials, including coal as well as ferrous and nonferrous metals. The extraction, storage, and refining of oil and gas is treated as a separate discipline. In all, there are 33 Soviet universities and institutes that train mining engineers for careers in the industrial, research and educational fields.

Jan 9, 1966

By W. W. Anderson

A formula for quantitative efficiency is proposed, in which the efficiency value is a function of the improperly distributed material at the, gravity of separation effected by the cleaning equipment. The misplaced material is expressed as a percentage of the total material discharged from the equipment. Numerous examples are given, demonstrating application of the formula to various types of separation, including multiple-product separations.

Jan 1, 1950

By G. M. BUTLER

TWENTY-ONE of the states in the Union, the Territory of Hawaii, and seven provinces of Canada now have in operation laws requiring that professional engineers be registered or licensed. In addition, two states require that civil engineers be registered, and one other state demands registration of structural engineers. Moreover, nearly every year sees additions made to the list. The registration movement, fostered by the American Association of Engineers, now has the powerful, energetic backing of the An1,erican Society of Civil Engineers, which is itself now fostering registration legislation, and there is a strong sentiment in favor of registration in the American Institute of Electrical Engineers and the American Society of Mechanical Engineers. Only in the American Institute of Mining and Metallurgical Engineers is anti-registration sentiment, strongly dominant, but many members of this organization are enthusiastic advocates of registration.

Jan 1, 1930

By A. E. Jenkins, L. A. Baker, N. A. Warner

Rates oj decarburization of levilated Fe-C droplets conlaining 5.5 to 0 pct C have been measured at 1660°C. Gas mixtures of 1, 10, and 100 pct 0, with helium diluenl were used at velocities of 12.5 and 62.5 cm per sec. Rates were independent of carbon concentration in the mell and in good agreement with the calculated rule of oxygen diffusion through the gas boundary layer. The effects of flow rale and total pressure are as predicled and the rates are approxitnalely 2.5 times those with CO2 as oxidant. The mass-transfer correlation used incorporaled the efject of natural convection as well as forced conrection. Graphile spheres are shown to oxidize at the same rate as Fe-C droplets under the same experimental codlions. It is concluded that, for high carbon concentrations in the melt, the rate of- decarburizalion is controlled wholly by the rate of gaseous diffusion. Rate measurements with pure CO, are reported for low carbon concentrations where CO bubbles nucleate within the droplet. Under these circumstances the decarburi-zation decreased with carbon concentration and it is proposed that carbon diffusion is significant in conlrolling the decnvburization rate. In an earlier paper1 decarburization rate measurements were reported for levitated Fe-C alloys at 1660°C but with CO2 as the oxidant. The decarburization rate was found to be independent of carbon concentration in the melt but slightly affected by total pressure. The authors were unable to explain the slight pressure effect but in all other respects the results were consistent with control by diffusion in the gas boundary layer. Subsequent work has been directed at finding the reason for the slight pressure effect and whether the kinetics with oxygen as oxidant parallel those with CO2. Recently Ito and Sano2 have shown that with water vapor-argon atmospheres the decarburization rate is gaseous diffusion controlled until an oxide film appears on the surface. In this work the melts were contained in crucibles. MASS TRANSFER IN THE GAS PHASE In the earlier analysis1 only forced-convection mass transfer was considered. Subsequent recognition of the existence of some free-convection mass transfer explained the observed small effect of total pressure on the decarburization rate. Steinberger and Treybal3 and Kinard, Manning, and Manning4 have developed correlations involving the linear addition of the contribution of radial diffusion, free and forced convection. Steinberger and Treybal&apos;s correlation was chosen as the most applicable to the present work since it correlated most of the data available in the literature and handled the low Reynolds number region exceptionally well. The correlation for (Gr&apos;Sc) < 108 is where Nu&apos; is the Nusselt number for mass transfer based upon the total surface of a sphere in an infinite medium, G&apos; is the mean Grashof number for mass transfer defined by Eq. [2], Sc is the Schmidt number (µ/pDAB)f, Re is the sphere Reynolds number (dpu,pf/µf), p is the viscosity of the gas (poise), p is the density of the gas (g cm-3), Dab is the binary diffusivity for the system A-B (sq cm sec-&apos;), dp is the sphere diameter (cm), u is the approach velocity of the gas (cm sec-I), and subscript f denotes the property value is computed at the film temperature Tf defined by Tf = +1/2(To + Tr) where To is the specimen temperature and T, is the approach gas temperature (oK). Natural convection occurs when inhomogeneities exist in gas density. These may be caused by concentration gradients, temperature gradients, or both. In the present work the temperature gradient between the sphere and the bulk gas was very large and in some cases, for example the runs with pure oxygen, the concentration gradient was also appreciable. The Grashof number defined by Mathers, Madden, and piret5 was used since it took account of both temperature and concentration gradients: where Gr&apos; is the Grashof number for mass transfer (p2fgd3|-yA-yA|/µ2f), Gr is the Grashof number for heat transfer (p2f gd3p|To - T,]/µ2fTf), Pr is the Prandtl number (cpµ/k)f, g is the acceleration due to gravity (cm sec-&apos;f, a is the concentration densification coefficient (1/p)(ap/ayA)T, yA is the mole fraction of component A at the gas-metal interface, yA is the mole fraction of component A in the bulk gas stream, cp is the heat capacity of the gas per unit mass at constant pressure (cal g-I OK-&apos;), and k is the thermal conductivity of the gas (cal cm-&apos; sec-1 OK-1). Mathers et al. tested this combined Grashof number

Jan 1, 1968

By James Bowron

CONSIDERING the importance of the steel trade and the strategic position occupied in it by the Birmingham District, it may be surprising to many to realize that even the first pig iron smelted with coke was made in Alabama on Feb. 28, 1876, although merchant pig iron had been produced in Rockwood, Tenn., in 1867, a plant which is still in active operation. The heavy deposit of Clinton ore extending from Pennsylvania into Alabama, varying greatly in accessibility on account of geological changes such as erosion or anticlinal upthrow, varies equally as much in thickness and in quality. The brown ores extensively scattered through the South also vary materially in quality, some being relatively low in phosphorus and high in manganese, and vice versa. The red ore varies materially in phosphorus, but the iron produced from these ores was always considered to be too high in phosphorus for treatment by acid Bessemer or open hearth and did not contain sufficient for the basic Bessemer process. Under these conditions there remained only the basic open hearth as a possibility, and for many years it appeared impossible to use it, because, with coke smelted iron, the silicon was too high to permit its use in basic lined furnaces.

Jan 1, 1924

CONTENTS PAGE FULTON, CHARLES H., and READ, J. BURNS-A New Roasting Furnace for Zinc Flotation Concentrate. Discussed by Charles H. Fulton, Arthur S. Dwight, B. M. O&apos;Harra, Kurt Stock 1 STOCK, KURT.-Redistillation of Zinc. Discussed by G. E. Dalbey, Kurt Stock.. 3 BEASLEY, F. E.-High Zinc in Lead Blast-furnace Slags. Discussed by R. C. Canby, R. L. Lloyd, C. R. Haywood, G. E. Dalbey, A. S. Dwight, E. P. Mathewson, A. L. Walker, B. M. O&apos;Harra, and C. P. Linville 4 STEELE, E. W.-Application of Pulverized Coal to Copper Refinery Furnaces. Discussed by F. R. Pyne, E. P. Mathewson 11 LINVILLE, C. P.-Recovery of Arsenic and Other Valuable Constituents from Speiss. Discussed by C. R. Hayward, C. P. Linville, G. E. Dalbey, A. S. Dwight, Edward F. Kern, Karl Eilers, E. P. Mathewson 12 A New Roasting Furnace for Zinc Flotation Concentrate Discussion of the paper of CHARLES H. FULTON and J. BURNS READ, presented at the New York Meeting, February, 1925, and issued, as Paper No. 1362-D, with MINING AND METALLURGY,. October, 1924. G. E. DALBEY, East Berlin, Conn. What would be the, effect on the formation of sulfates of an increased water vapor content in the roasting gases? CHARLES H. FULTON.-I cannot answer that from our experience. The question of the formation of sulfate in the roasting of zinc is mainly one of temperature and the concentration of S02 and S03 in the gases. We found we could roast almost completely to sulfate if the concentration was kept at the proper point. We, however, did not care to do this because we wished to make a 5 to 6 per cent. S02 gas for sulfuric-acid work. The sulfating of the zinc oxide in the proper concentration of gases goes on very rapidly. There are certain places in the furnace system such as the Cottrell and in a part of the dust chamber in which the roasted

Jan 6, 1925

By R. Gilman Brown

INTRODUCTION. MINES are interesting by reason of what they have done for man, or of what has been done for them by nature. Not all are interesting on both scores. Many profitable mines are commonplace to the geologist; and many presenting unique geological conditions have been sad failures commercially. The Standard group at Bodie has produced in 25 years, $14,500,000, paying $5,000,000 in dividends.&apos; On the other hand, this output has been mined (almost wholly above the 1,000-ft. level) from a system of more than 100 veins, ranging in thickness-from 0.5 in. of "specimen rock" to 30 ft. of clay and quartz; distributed through a zone about 2,000" ft. in width, and representing from three to five distinct periods of formation. This group, therefore, by reason of its industrial record as well as its geological features, may fairly be regarded as doubly interesting. The Bodie district occupies an island of recent (Tertiary) hornblende-andesite, surrounded by a complex of igneous rocks and breccias. It lies at the summit of the eastern foot-hills of the Sierra Nevada mountains, and within the Great Basin, a few miles from its western edge, marked here by Mono lake on the line of the Great Fault. The average elevation of the outcroppings of the veins may be taken at about 5,700 ft. The andesite projects from south to north in a great tongue, 12,000 ft. long and 5,000 ft. wide, reaching an extreme height at the northern end of perhaps 1,000 ft. above the adjoining small canyons. These separate it from the main mass of the foot-hill

Jul 1, 1907

By A. Manganwidjoyo, W. A. Wiebenga

The aim of this paper is to disclose some of the correlations between rock parameters, hidden in Wuerker&apos;s "Annotated Tables of Strength and Elastic Properties of Rocks," 1956. The empirical relations concern dry rocks of varying porosity. Curves and equations interrelating the specific gravity, compressive strength, bar velocity, and Poisson&apos;s ratio are presented. In 1956 Wuerker published his "Annotated Tables of Strength and Elastic Properties of Rock", in which various physical properties of rocks determined by different authorities, are tabulated systematically. The tables are primarily intended for use by mining-, quarrying- and ore-dressing engineers. Since the list of measured parameters for each type of rock includes properties such as — grain size, specific gravity, porosity, compressive strength, static elastic cons:ants (moduli of elasticity, rigidity, specific damping capacity and longitudinal bar velocity) the tables are also of considerable interest to the practical geophysicist. Correlations between rock parameters may enable geophysicists, geologists and civil engineers to transiate measurements from one parameter to another. Even if these translations are of limited accuracy, or valid only within certain specified ranges, they often serve a useful parpose. The aim of this paper is to disclose some of the correlations between rock parameters concealed in wuerker&apos;s Tables. Throughout this paper the following symbols and units are used unless otherwise stated: Sg is Specific gravity, the ratio of the density of a specimen to the density of water at 4°C. P is Porosity, in %, the ratio of the volume of voids in a specimen to its total volume. CS is Compressive strength in 1000 p.s.i., the stress under which a specimen will fracture when undergoing a standard compression test. V is Bar Velocity in kilo-feet/sec, the velocity of longitudinal seismic waves measured in a slender bar type specimen. Vc is Bulk or Constraint Velocity in kilo-feet/ sec, the velocity of longitudinal seismic waves measured in a very large specimen.+is Reciprocai bar velocity in millisecs/ft (1 millisec = 10-3 sec). cis Poisson&apos;s ratio, the ratio of the lateral to longitudinal strain of a body under longitudinal stress. CORRELATIONS Specific Gravity (Sg) vs. Porosity (P) Figure 1 is a diagram illustrating the relatiooship between specific gravity and porosity for approuirr~ately 70 samples of dry rocks. A curve fitted by estimation to this data yields the empirical formula: Sg =-0.0268P + 2.67 * 0.2 (1) Considering unit volume of a porogs specimen then

Jan 1, 1961

By W. E. D. Stokes

WHEN history is written, the year of the blitzkrieg will go down as giving aviation its greatest impetus. No perceptible drop in military business, even with cessation of hostilities abroad, seems likely. The combined air force of the U. S. Army and Navy on July 1 was approximately 5000 planes, as against 50,000 planes currently discussed as necessary. Observers at the fronts are giving designers and metallurgists back home some realistic ideas to shoot at. As conventional runways reveal the location of airports to enemy raiders, operating bases are now masked. Difficult, often muddy and rough landing strips, requiring strong landing gears and exacting take-off and maintenance characteristics, are the specifications of war. This is "old stuff" to numerous mining operators in mountainous jungle areas where gradients up to 8 per cent are in more or less common use in such mountain landing fields. Although airplane building is not readily adaptable to assembly-line methods, a trend towards mass productions is now in evidence. Incidentally, a U.S. Army "Curtiss P-40" requires about 10,000 man hours of work to complete and is tied together with 75,000 rivets. During the past year a number of aircraft factories adopted the "shot-

Jan 1, 1941

By S. A. TAYLOR

THERE is probably no other mineral industry of which the public has as much information and misinformation as it has of the coal industry. Unfortunately, however, the general public&apos;s knowledge of the coal industry, outside of the particular kind of coal it is accustomed to, by reason of use, is largely made up of information received from newspaper and popular magazine articles, in which the mine workers are depicted as overworked and mistreated men, and the coal operators as "coal barons." Those who have any specific knowledge of exact conditions in the coal industry know how unjust and un- fair such an opinion of the coal industry is, not only to the miner but to the operator as well. Many reporters and writers of magazine articles are misled by statements regarding the condition of the miners that are exaggerated and not founded on facts and, if an investigation of the conditions of the miner&apos;s work, his habitation and surroundings were fairly made, it would at least compel more truthful statements by those who write for public reading. That such an investigation would not reveal anything that was wrong, or anything to be censured or cured, no one, I think, would maintain, but I do think that any fair investigation of the facts would show that conditions in and around the newer and later-developed coal mines and communities would compare favorably with those of manufacturing districts, and that where the mines and com- munities are old and not very attractive places to work, or live in, they carry with them other considerations, compensating for these conditions, and cannot be remedied by reason of a lack of sufficient coal to warrant economically any costly changes.

Jan 1, 1926

By H. Wilhelm, E. L. Davis, W. A. Clark

MATHEMATICAL formulas for the analysis of the behavior of producing oil wells can be devised which will be correct for the assumed conditions. However, in an oil zone, variables always exist which are unknown, or to which. it is impractical to assign mathematical values. It seems apparent that one should reason back from observed facts to an analysis of causes, rather than start with a hypothetical reservoir with assumed properties and attempt to explain observed phenomena. In this paper we hope to throw some additional light on factors influencing production, especially edgewater behavior. OIL and gas are contained in reservoirs of either the sealed type or the edgewater type. In the former all the recoverable oil is produced by gas expansion only. In this type of reservoir, edgewater is not effective. This may be because of faulting or overlapping strata, or more often, probably, the edgewater pressure is ineffec¬tive on account of resistance or lack of head.

Jan 1, 1933

Jan 1, 1881

By R. S. McClellan

DURING the last year or so, with higher prices for gold and silver, many old properties in the West have come back to life. Almost every profitable producer in the old days has been considered, and the reasons for its shut-down investigated. If it seems likely that modern ore-finding, mining, and metallurgical methods, and S35 gold can again put the property on a profitable basis, someone can usually be found to back the venture. Methods of rejuvenation vary with the property, of course, but the following outline of what has been done with one group of mines in Idaho is fairly typical and may be suggestive to others. The Golden Chariot gold-silver properties, near Silver City, consist of seven old mines, working a vein system striking north and south, which had a productive length of some 3500 ft. The vein is a quartz-filled fissure with granite walls. Gold occurs in native, and with silver in the form of electrum which is the natural alloy of the two metals. Silver also occurs in a variety of sulfides. From 1064 to 1876, these old properties were worked intensively to an average depth of about 700 ft., through seven shafts which range in

Jan 1, 1934

By R. Webeler

In order to study the role of work hardening in the fatigue process, use was made of the great sensitivty of the resistivity of AuCu to cold work. A change of the resistivity of AuCu of the order of 1 to 2 pct at the temperature of liquid nitrogen was found to occur as a consequence of severe fatigue. ACCORDING to Orowan&apos;s theory,&apos; the process of fatigue In metals 1s associated with the production of a number of small regions which have undergone strain hardening. This phenomenon is supposed to occilr even if the stress applied during fatiguing is always smaller than the yield stress. In an attempt to verity the existence of such regions, Welber and Webeler&apos; undertook to detect the stored energy associated with severe fatigue in copper. Previous experiments" had shown that the energy stored in a sample of copper which has been cold worked by torsion is released in the temperature range between 150" and 250°C when the sample is heated from room temperature and that no more energy is released (or absorbed) between 250" and 450°C. In particular the stored energy amounted to 0.41 cal per g for a case in which the mechanical energy expended in twisting the sample was 11.9 cal per g. In the case of fatigued copper, however, no release of stored energy could be detected between 150" and 250°C, so that the experimental error of &0.02 cal per g represents an upper limit for the amount of energy stored in strain hardening., It seemed desirable to attack the problem in a new fashion. For this purpose, it was decided to make use of the fact that, if an alloy capable of undergoing the order-disorder transition is ordered and then cold worked, the resistivity, p, increases very greatly above the value for the ordered state even if the deformation is very small. Some insight into the nature of the fatigue process may be obtained then by measuring the resistivity of an ordered sample before and after subjecting it to fatigue. For reasons which will become apparent from the following remarks, considerably more can be learned by carrying out the resistivity measurements at two different temperatures. In the case of a material containing impurities, vacancies, dislocations, or other imperfections of essentially atomic dimensions, the resistivity, p, according to Matthiessen&apos;s rule, can be represented as a sum of two terms p = p, + p, where p, is the (temperature dependent) resistivity of the pure metal, and p, is the temperature independent contribution of the imperfections. Briefly, the physical basis for this rule is the following: The main contribution of the impurities in question to the resistivity results from the fact that they interrupt the periodicity of the lattice and thus scatter the conduction electrons with a probability which is almost independent of temperature. In order that this be the case, it is necessary that the&apos; extension of the impurities be small enough—roughly less than one electron mean free path—so that their main effect on the resistivity occurs for the foregoing reason. If an alloy like AuCu is partly or completely disordered by quenching from an appropriate temperature, Matthiessen&apos;s rule also applies to a very good approximation* with p, representing in this case the resistivity po of the ordered sample and p, the additional (temperature independent) resistivity due to the disorder. In general, the disorder can be represented in terms of atoms which are displaced from their "proper" positions in the superlattice and which thus qualitatively represent the imperfections in the superlattice responsible for the term p,. Since the misplaced atoms are distributed at random throughout the super-lattice, their contribution to the resistivity still can be considered in terms of the scattering of conduction electrons by lattice defects. The situation is somewhat more complex in the case of an alloy disordered by cold work because the process of disordering here does not involve a random redistribution of the atoms; however, Matthiessen&apos;s rule also holds in this case. Whenever Matthiessen&apos;s rule does apply, the values of the quantity /3 = (p? — /(T, — T,), where p, and p, are the values of the resistivity at two fixed temperatures, T, and T,, respectively, is constant (independent of p,) for a given alloy or metal. In particular, if a sample of AuCu is subjected to ordinary cold work, the value of /3 remains equal to Po, the value for the ordered material. According to Orowan&apos;s theory,&apos; as remarked before, a fatigued sample contains a large number of isolated severely cold-worked regions, which make up only a small proportion of the metal. Thus, if a sample of AuCu initially in the ordered state is fatigued, more or less disordered regions will be produced within the ordered material. If these regions are small enough so that Matthiessen&apos;s rule applies, then it follows from the previous discussion that /3 again will remain equal to Po. If the effect of fatigue is to produce cold-worked regions which are macroscopic—of the order of at least several electron mean free paths—the effective resistivity, p, has to be computed by use of the ordinary laws of large-scale electrodynamics. For the sake of simplicity, it will be assumed here that the cold-worked regions are completely disordered and have a resistivity, p,. For a given proportion A of disordered regions the effective resistivity, p, for the current in a given direction depends on the geometrical configuration of these regions. In any case, the value of p for such

Jan 1, 1956

By Sheldon P. Wirnpfen

AN extensive study of German underground manufacturing experience is being undertaken by the Air Materiel Command. Headquarters officials consider completely underground facilities one of the most effective means of protecting aircraft production against air attacks of the strength and type employed in World War II. Advantages accruing to underground manufacturing installations other than protection are, perhaps, a smaller maintenance problem and the possibility of using gravity flow on some production lines. Offsetting these advantages are the high cost of construction, problems of ventilation, and poor acoustics. Excavation costs might well be less than the cost of enclosing the same area on the surface, as new and better methods of rock drilling and transportation are developed. Certainly the amount of building materials used would be far less than in constructing a surface plant of the same dimensions. A fewer number of skilled workers would be required to perform the labor of excavation. Underground construction would

Jan 1, 1947

By Michael S. Koleda

Less than two years ago, the, Congress, with broad bipartisan support, passed the Energy Security Act of 1980. A decade marked by ten- fold increases in world oil prices and two major interruptions in oil flows from the Middle East had ended. An all-out national commitment to transform America&apos;s vast tar sands, oil shale and coal resources into conventional fuels had begun. The national synfuels effort was to be public-private cooperation at a scale unmatched in peace time. Private industry would own and operate the synthetic fuels facilities. Government would reduce market uncertainties to acceptable levels. The potential government commitment was substantial. Up to $88 billion would be available through the Synthetic Fuels Corporation, principally in the form of contingent financing. Billions more would be spent through Department of Energy programs. Additional incentives for alternate energy development were contained in the Energy Tax Act of 1978. The Energy Security Act clearly specified national synthetic fuels production objectives: 500,000 barrels per day by 1987 -- 2 million barrels per day by 1992. Finally, said Congress, Uncle Sam was going to do something about rapidly rising oil prices, uncertainties of energy supply, and the resulting disruption to the U. S. economy. Simply put, the purpose of the Energy Security Act of 1980 was to provide government guarantees sufficient to get synthetic fuels projects off the private sector drawing boards and into commercial production. Because of their huge cost, technological uncertainty, and lengthy pay-out period, these projects were always second place to projects of smaller size, known technology and more rapid pay-out. The Energy Security Act was the legal expression of public policy to bring the free-market synfuels timetable into line with the faster paced political timetable in the interest of national energy security.

Jan 1, 1982

By Roger K. Clifford, Gary W. Hudiburgh

The amine flotation of feldspar from a magnetite concentrate produced at a domestic concentrator was investigated using zeta potential measurements, Hallimond tube flotation tests, and laboratory-scale flotation tests. The point of zero charge of six feldspars (microcline, orthoclase, albite, anorthite, anorthoclase, and oligoclase) range from pH 1.4 to 2.5. Hallimond tube flotation tests using amine flotation reagents were performed on these feldspars and on gangue material (quartz, albite, and microcline) from the magnetite concentrating plant. Laboratory-scale (623 g and 2500 g) flotation tests were performed on the magnetite concentrate to float the feldspar. The effects of three different collectors, two levels of collector concentration, three pH levels, starch, HF acid and regrind were investigated.

Jan 1, 1977