Search Documents

DAVID THOMAS 1871 R. W. RAYMOND 1872-1874 A. L. HOLLEY 1875 ABRAM S. HEWITT 1876 T. STERRY HUNT 1877 ECKLEY B. COXE 1878-1879 WILLIAM P. SHINN 1880 WILLIAM METCALF 1881 RICHARD P. ROTHWELL 1852 ROBERT W. HUNT 1883 JAMES C. BAYLES 1884-1855 ROBERT H. RICHARDS 1886 THOMAS EGLESTON 1887 WILLIAM B. POTTER 1888 RICHARD PEARCE 1889 ABRAM S. HEWITT 1890 JOHN BIRKINBINE 1891-1892 H. D4. HOWE 1893 JOHN FRITZ 1894 J. D. WEEKS 1895 E. O. SPILSBURY 1896 THOMAS M. DROWN 1897 CHARLES KIRCHHOFF 1898

Jan 1, 1942

By Paul Beck

WHILE the recrystallization properties of most of the practically important metals are known in considerable detail, those of lead are still relatively little known in spite of some valuable contributions in recent years. This condition probably is due to the difficulties involved in applying the usual methods of investigation. The microscopic method of discriminating between the elongated deformed grains of the familiar lenticular shape and the equiaxed recrys-tallized grains is not successful with fully refined lead: lenticular grains cannot be seen under the microscope with any amount of deformation whatever. The probable cause of this phenomenon was recognized long ago. With large deformation the time of recrystallization at room tem-perature is shorter than the period of preparation of the specimen for microscopic examination; with small deformation the deformed grains are not noticeably elongated in the first place. However, with small deformation the migration of the grain boundaries can be observed. The only systematic investigations yet published on the recrystallization of lead, those by R. S. Russell,1-3 make use of the conditions just described. Russell considered recrystallization completed when no further migration of boundaries could be observed. A serious objection to this method arises from the fact that there is no evidence to support the view that grain-boundary migration results only from recrystallization. If such migration does result from other sources after recrystallization is com-pleted-after the deformed grains have been replaced by new unde-formed grains-the "time of recrystallization" as determined by Russell may be too long. Furthermore, the method is subject to the above-mentioned limitation because of the unavoidable period of preparation of the sample. According to Russell, even with the fastest technique 5 min. elapsed before the deformed samples were ready for examination, and consequently no recrystallization time shorter than 5 min. could be measured.

Jan 1, 1939

By James Aston

A PROPER consideration of this subject is not confined to the technical channels of production and metallurgy. It concerns an industry, and should cover economic aspects which are of material importance in any program of development. The discussion may logically be treated under three subdivisions, as follows: (1) manufacture, (2) characteristics related to quality of material; (3) adaptability and exploitation of product. MANUFACTURE OF WROUGHT IRON The manufacture of wrought iron is the most ancient art of the ferrous metal industry. The eighty years or less of existence of processes identi-fied with our modern "Age of Steel" is a relatively brief interval com-pared with the several thousand years associated with the production of wrought iron by man. From the primitive early methods of production, manufacture for many centuries followed the line of direct reduction. There were developments as experience was gained through the years; but man's needs for a strong, ductile, forgeable product were met by reducing the ore to metallic iron in a single-stage operation. Following the development several centuries ago of what has become our modern blast-furnace operation, manufacture of wrought iron was gradually transformed into a two-stage method of first producing cast iron and then refining this to the desired degree of forgeability; the fore-runner in principle of today's scheme of manufacture of steel. The product retained the essential characteristics of highly refined base metal with iron-silicate slag incorporation, which were associated with the material resulting from direct reduction methods. Cort's invention of the puddling process in 1784 is a landmark in wrought-iron manufacture. It consisted essentially in adapting a coal-fired reverberatory furnace to the refining operation; thus lifting the industry out of the slough of

Jan 1, 1935

By Allen Garrison

A PREVIOUS paper1 reviewed some of the properties of clays and shales and presented some data on the nature of the gelling phenomenon. It included a brief discussion of origin of clays and shales, their com-position, structure, retention of water, ionization, base exchange, and the nature of the gelling of water suspensions, Other publications of the Institute2-8 have discussed the properties of clays and their relations to drilling-fluid behavior and control. It is the purpose of this article to present some new data obtained and arranged in a different manner and making possible a better understanding of the chemical reactions involved in the control of drilling-fluid characteristics during the normal drilling operations. EXPERIMENTAL PROCEDURE The difficulties involved in the measurements of the flow character-istics of plastic fluids are too familiar to recite, The possible applications of some of the well-known instruments to this problem have been ade-quately discussed by Hobson9 and he has given an excellent bibliography. Although there are many viscosimeters of varied design, none of them appear to fulfill the most obvious demands of accuracy in the measure-ment of clay or shale suspensions, Since the fluid characteristics are dependent on the rate of flow of the fluid, and the viscosity usually falls off very rapidly as the rate is increased, it is clear that the first require-ment is that the instrument shall be capable of a wide variety of speeds. The viscosity of the fluid at any fixed and constant rate of flow is also a function of time, so that the second demand is that the instrument shall be capable of a constant and continuous motion for a prolonged period of time.

Jan 1, 1939

By M. H. Sommer

MANY attempts have been made to develop a relation between the tensile properties and the deep-stamping qualities of metals com-monly used in deep drawing. These operations are generally performed cold and the metal is always stressed beyond the elastic limit. However, the problem cannot be readily solved without a proper investigation of (1) the relation between actual stress and actual strain in the plastic range and (2) the stresses that are set up in the metal during the process of deep stamping. Much work has been done in recent years to add to our knowledge on plastic deformation of metals and the shortcomings of the ordinary tensile test, particularly in the plastic range, have been sufficiently recognized. It has been widely acknowledged that the local contraction, which appears in a tensile test after the maximum load is reached, is not a general characteristic of the material but is peculiar to this form of testing. The plastic deformation of materials is explained by the slip of their crystals along certain planes and this rearrangement should be similar whether observed in a tensile, compression or torsion test, and if the results of any of these forms of testing show deviations, it must be due to other influences, as for example the local contraction in a tensile test. For this reason the tensile-test curve as obtained from the measurements taken on a tensile-test machine or registered by an autographic device has been supplemented by the so-called "actual stress-strain curve," which is constructed from the observed tensile-test data by eliminating the effect of local contraction and is in complete alignment with the stress-strain values obtained in a compression or torsion test. The actual stress-strain curve shows the increase of actual unit stress in relation to unit elongation beyond the yield point and

Jan 1, 1934

By R. M. Hudson

Equilibrium constants have been determined for the jeaction C (in steel) + H2O = CO + H2 as a function of carbon content (0.013 to 0.74 ujt pct) and temperature (1200° to 1800°F) by using a flow system in which the water-vapor content of various gas mixtures containing hydrogen, carbon monoxide, and nitrogen was systematically controlled. The equilibrium partial-pressure ratio K1 = PcoPH2/PH2O was obtained for two low-carbon steels and four Fe-C binaries from a series of runs made at each temperature. By comparison of Ki with the analogous ratio for the reaction C (graphite) + H2O = CO + H2, the activity of carbon in steel (ac) was comDuted for each temperature and carbon content studied. From these data values of the equilibrium constants for two other carburization-decarburiza-tion reactions of importance were estimated. The chemical compositions of the two steels and four Fe-C binaries used are given in Table I. Specimens of Steel E were cut from a 0.035-in.-thick commercially box-annealed and temper-rolled lot of a low-carbon low-metalloid steel. Steel F was a commercially hot-rolled rimmed steel that was cold-reduced at the Laboratory to a 0.059-in. thickness. Fe-C binaries A, B, C, and D were vacuum-melted and poured, hot-rolled, pickled, and cold-reduced at the Laboratory to furnish specimens 0.035 in. thick. Sheet specimens were cut from all lots to approximately 3/4 by 3 in. by gage and were vapor-degreased with trichlo-roethylene and weighed before heat treatment. Heat treatments were carried out in a hinged-top Hevi-Duty electric furnace with a Vycor-glass tube. When the furnace was at the desired

Jan 1, 1965

By A. A. Berk

LAGGING technology and the slow spread of information have been the chief obstacles to widespread participation in minimizing the industrial pollution load. These obstacles can be conquered by fact finding and applied research. There are three aspects to the problem of water-borne mineral waste: to minimize the amount being thrown away, to select a predisposal treatment, and to use the products or dispose of them. It is often possible to minimize the waste by making very minor changes in the process that produces it. For example, a manufacturer of automobile bumpers greatly reduced the dragout 'from a plating bath by modifying the design and position of two boltholes.' A plater of automobile hubcaps installed a drainage bar and decreased the loss of chrome-plating solution to the rinse water by about 80 pct.' The mill at a western mine found it possible to discard 60 to 70 pct of an ore with minimum treatment," so that the processing effort could be concentrated on a high-graded slime, with significant reduction in costs and improvement in recovery. The possibilities for waste reduction through process changes are limited only by the imagination. A recent patent points out the advantages of using No. 1 fuel oil instead of water in wet-process cement making;& the fuel oil presumably has better properties than water for this purpose and is said to be almost com'pletely recovered or utilized, so that there is no waterborne waste. Recycling to reduce wastes and improve process economy is very well illustrated in vanadium and uranium recoveries from relatively low grade ore. Ores containing 6 pct calcium carbonate were found to give poor vanadium recovery by the salt-roasting process because the vanadium was converted to water-insoluble calcium vanadate. Following the salt-roasting process, sulfuric acid was used to leach the uranium. Enough calcium sulfate was formed

Jan 1, 1958

By William Fink

Two of the aluminum-alloy systems previously studied-the alumi-num-titanium and the aluminum-chromium-exhibit a peritectic reaction at the extreme aluminum end of the diagram. Preliminary work indi-cated that the aluminum-zirconium and certain other aluminum systems were similar in this respect. The present paper, the twentieth of a series from the Aluminum Research Laboratories, reports the results of a recent investigation of equilibrium relations in aluminum-zirconium alloys of high purity, which confirm the preliminary observations. PREVIOUS INVESTIGATIONS There has been only one investigation of the aluminum end of the aluminum-zirconium system. Sykes1 prepared and studied alloys containing 0 to 70 per cent Zr. The lowering of the freezing point of aluminum by the addition of zirconium was found to be very little, if any (less than 2°C.). He placed the solid solubility of zirconium in aluminum at room temperature between 0.57 and 0.97 per cent. A few other investigators have attempted to determine the com-position of the intermetallic compounds occurring in this system. Hönigschmid2 obtained the compound ZrAl3 as a by-product during the preparation of ZrSi2. He made no attempt to prepare other aluminum-zir-conium compounds. Weiss and Newmann3 prepared an alloy by heating aluminum with a double fluoride of potassium and zirconium. When this alloy was treated consecutively with caustic soda and hydrochloric acid, there was a residue, which contained approximately 72 per cent Zr and 28 per cent Al (Zr3Al4). Marden and Rich4 prepared an alloy in the same way, treated it with caustic soda, and obtained a residue of silver-white crystals, which contained 70 per cent Zr and 30 per cent Al (Zr3Al4).

Jan 1, 1939

By Kenneth M. Bravinder, Jonathan E. Koogle, Dean H. Sheldon

The solution of subsurface geological problems requires an analysis of vertical and horizontal dimensional relationships. For many, the ability to visualize structures in three dimensions is not easily acquired, and for areas where the structural conditions are complicated by faulting the need arises for illustrative models. This has led to the many forms of peg models, in which the usual course of construction includes a peg for the well bore, and the suspension of strings from peg to peg to illustrate the formation correlation between wells, thus developing the usual folds and flexures. Such models proved unsatisfactory for the analysis of fault problems. Consideration was then given to the use of transparent materials. A model of the Dominguez oil field was constructed in 1935, which consisted of a series of glass panels irom well to well on which the formations were shown in color. This model, though serving its purpose at the time, proved to be impractical from the standpoints of cost, breakage hazard, and extreme difficulty in maintenance. The cost of materials was estimated to be approxi-mately $300, and the construction required the services of one man for a period of from 10 to 12 months. Maintenance after actual construction was an additional expense. Consideration was then given to the use of celluloid, and aiter some experimental work it was found that the advantages in its use were: (I) a short construction time, (2) ease of handling the material, (3) sec-tions are easily reworked, (4) low cost. Construction It would be of little value to recount here the difficulties encountered in the building of the first celluloid model. The conclusions drawn, however, suggest the following pro-cedure for those who contemplate the construction of such a model: 1. Determilzatiolz of the Scale.—Accurate geological interpretation requires the use of the same scale horizontally and vertically. It should be emphasized that the limited size of the celluloid sheets (20 by 48 in. maximum dimensions), the area to be studied, the maximum depths to be plotted, and area of possible future development are the controlling factors in adopting a scale to he used. 2. Construction of the Base.—A satisfac-tory base may be constructed by using two pieces of three-ply wood separated by strips of I by 2-in. material. This type of construction prevents warping of the base. The size of the base is determined by the dimensions of the area to be studied plus 5 in. on all sides. A map of the same scale as that adopted for the model, indicating the lines of section to be used, should be fastened to the base. 3. Constructiolt of the Frame (Fig. I).—In the construction of the frame the use of %-in. 0.d. pipe welded in a box shape is suggested, with two horizontal rods on each of the four sides, top and bottom. The top rod should be at least r in. higher than the

Jan 1, 1941

By Kenneth M. Bravinder, Jonathan E. Koogle, Dean H. Sheldon

The solution of subsurface geological problems requires an analysis of vertical and horizontal dimensional relationships. For many, the ability to visualize structures in three dimensions is not easily acquired, and for areas where the structural conditions are complicated by faulting the need arises for illustrative models. This has led to the many forms of peg models, in which the usual course of construction includes a peg for the well bore, and the suspension of strings from peg to peg to illustrate the formation correlation between wells, thus developing the usual folds and flexures. Such models proved unsatisfactory for the analysis of fault problems. Consideration was then given to the use of transparent materials. A model of the Dominguez oil field was constructed in 1935, which consisted of a series of glass panels irom well to well on which the formations were shown in color. This model, though serving its purpose at the time, proved to be impractical from the standpoints of cost, breakage hazard, and extreme difficulty in maintenance. The cost of materials was estimated to be approxi-mately $300, and the construction required the services of one man for a period of from 10 to 12 months. Maintenance after actual construction was an additional expense. Consideration was then given to the use of celluloid, and aiter some experimental work it was found that the advantages in its use were: (I) a short construction time, (2) ease of handling the material, (3) sec-tions are easily reworked, (4) low cost. Construction It would be of little value to recount here the difficulties encountered in the building of the first celluloid model. The conclusions drawn, however, suggest the following pro-cedure for those who contemplate the construction of such a model: 1. Determilzatiolz of the Scale.—Accurate geological interpretation requires the use of the same scale horizontally and vertically. It should be emphasized that the limited size of the celluloid sheets (20 by 48 in. maximum dimensions), the area to be studied, the maximum depths to be plotted, and area of possible future development are the controlling factors in adopting a scale to he used. 2. Construction of the Base.—A satisfac-tory base may be constructed by using two pieces of three-ply wood separated by strips of I by 2-in. material. This type of construction prevents warping of the base. The size of the base is determined by the dimensions of the area to be studied plus 5 in. on all sides. A map of the same scale as that adopted for the model, indicating the lines of section to be used, should be fastened to the base. 3. Constructiolt of the Frame (Fig. I).—In the construction of the frame the use of %-in. 0.d. pipe welded in a box shape is suggested, with two horizontal rods on each of the four sides, top and bottom. The top rod should be at least r in. higher than the

Jan 1, 1941

By Michel T. Halbouty

The area for which oil and gas developments in South Texas are reported for 1940 in this paper covers the same counties that were included in the reports for 1938 and 1939, with the addition of LaSalle County. LaSalle County is includcd in the Laredo district of South Texas, which totals seven counties for that district. The Corpus Christi district remains the same, with nine counties. The two districts together comprise what is known as the South Texas area for this report. Continued exploration along established trends and beyond proven field limits during 1940 provided South Texas with new fields and new producing levels at a rate of discovery fairly comparable with the high records set during recent years. The wells drilled in the counties within this district (including LaSalle) numbered 1656, approximately 8 per cent below the 1801 figure of last year. However, rank wildcats totaIed 336, an increase of 17.5 per cent compared to the 286 drilled in 1939. Therefore, since new field discoveries numbered 25 in 1940 against 29 in 1939, the rate of new field discoveries in 1940, based upon rank wildcats drilled, was I/I3.4 while that of 1939 was I/9.86, which shows a decrease of about 25 per cent in the rate of new fields. The rank wildcat tests in 1940 gave the following results: 18 produced oil, 4 produced distillate with gas, 3 produced. only gas, and 3r1 were dry holes (Table 5). Of the 1320 tests drilled in already proven fields or as extensions to pro+en areas (representing a decline of 12.8 per cent from last year's total of 1515 tests), 1048 produced oil or distillate, 60 produced gas and 212 were dry holes (Table 4). Of the producers, 50 found new sands or crude-in-distillate-sands in existing fields. Among the several fields subjected to extensive development were: Colorado, Jim Hogg County; East White Point, San Patricio and Nueces County; Rincon and Sun, Starr County; Glen, Webb and Zapata Counties; Wade City and Orange Grove, Jim Wells County; Stratton and South Clara Driscoll, Nueces County, and Aransas Pass, San Patricio and Aransas Counties. The development of important crude reserves on structures formerly considered primarily distillate fields has probably been the most important phase of the year's operations in South Texas. The Rincon, Stratton, Agua Dulce, Wade City, Odem and Robston fields provided the new crude sand discoveries. At some places crude production was opened by exploratory wells that found new sand horizons; in others by flank wells that found already discovered distillate sands sufficiently low to provide crude production. Rincon, Starr County, with its multiple sands, is now believed to be one of South Texas' largest crude-oil reserves. Offshore drilling showed important results during the year, including the discovery of two new submerged fields and the extension of the East White Point field into offshore Nueces County. The new marine fields are: East Flour Bluff) 76

Jan 1, 1941

By Michel T. Halbouty

The area for which oil and gas developments in South Texas are reported for 1940 in this paper covers the same counties that were included in the reports for 1938 and 1939, with the addition of LaSalle County. LaSalle County is includcd in the Laredo district of South Texas, which totals seven counties for that district. The Corpus Christi district remains the same, with nine counties. The two districts together comprise what is known as the South Texas area for this report. Continued exploration along established trends and beyond proven field limits during 1940 provided South Texas with new fields and new producing levels at a rate of discovery fairly comparable with the high records set during recent years. The wells drilled in the counties within this district (including LaSalle) numbered 1656, approximately 8 per cent below the 1801 figure of last year. However, rank wildcats totaIed 336, an increase of 17.5 per cent compared to the 286 drilled in 1939. Therefore, since new field discoveries numbered 25 in 1940 against 29 in 1939, the rate of new field discoveries in 1940, based upon rank wildcats drilled, was I/I3.4 while that of 1939 was I/9.86, which shows a decrease of about 25 per cent in the rate of new fields. The rank wildcat tests in 1940 gave the following results: 18 produced oil, 4 produced distillate with gas, 3 produced. only gas, and 3r1 were dry holes (Table 5). Of the 1320 tests drilled in already proven fields or as extensions to pro+en areas (representing a decline of 12.8 per cent from last year's total of 1515 tests), 1048 produced oil or distillate, 60 produced gas and 212 were dry holes (Table 4). Of the producers, 50 found new sands or crude-in-distillate-sands in existing fields. Among the several fields subjected to extensive development were: Colorado, Jim Hogg County; East White Point, San Patricio and Nueces County; Rincon and Sun, Starr County; Glen, Webb and Zapata Counties; Wade City and Orange Grove, Jim Wells County; Stratton and South Clara Driscoll, Nueces County, and Aransas Pass, San Patricio and Aransas Counties. The development of important crude reserves on structures formerly considered primarily distillate fields has probably been the most important phase of the year's operations in South Texas. The Rincon, Stratton, Agua Dulce, Wade City, Odem and Robston fields provided the new crude sand discoveries. At some places crude production was opened by exploratory wells that found new sand horizons; in others by flank wells that found already discovered distillate sands sufficiently low to provide crude production. Rincon, Starr County, with its multiple sands, is now believed to be one of South Texas' largest crude-oil reserves. Offshore drilling showed important results during the year, including the discovery of two new submerged fields and the extension of the East White Point field into offshore Nueces County. The new marine fields are: East Flour Bluff) 76

Jan 1, 1941

AS provided in Article VIII, Section 4 of the By- laws, the Papers and Publications Committee has formulated the following, rules of pro-cedure and submitted them to the Board of Directors for consideration and approval. In preparing these rules the committee, and an active subcommittee con-sisting of Messrs. Norris, Sharpless; Fohs and Wither-ell, have kept in mind the desirability of codifying the practice that has grown up through the now sev-eral years of experience of the committtee, without casting them in a mold so rigid as to be hampering. The problems of the Institute change from year to year and the methods of publication must change also to meet each new situation as it arises. "The estab-lishment of divisions and special volumes devoted to the papers. read before each required certain changes from former practice. These rules have been framed with this in view. The committee suggested, however, in its letter of transmittal, that the system will be made all the more workable if the Board will, as far as practicable, in making appointments to this committee, arrange for representation from each of the professional divisions and technical committees. It is understood that the chairman of the committee will be named by the Board. The rules regarding spe-cial volumes have been framed, keeping in mind the present policy of distribution, as already approved by the Directors under which the special volumes go only to the special. groups except on request. The committee has not attempted to provide rules governing consideration of any appeal made to the Board from one of its decisions, but its services and files will necessarily be at the full service of the Board in any such event. The rules which were ap-proved by the Board at its meeting on March 30, 1928, are as follows: Signed by C. S. Witherell, Chairman. (A) The authority of. the Committee on Papers and Pub-lications, hereinafter called the Committee, is defined in Art. VIII, Sec. 4 of the By-laws of the Institute, which reads as follows: "Papers and Publications: The Committee on Papers and Publications shall consist of the Secretary of the Institute, and at least twelve members of the Institute, to assist in passing on all papers offered for publication. They shall be appointed annually by the Board of Direc-tors, on recommendation of the President, and shall have authority, subject to appeal to the Board, to accept or reject papers for publication in the Transactions and Technical Publications of the Institute. The Commit-tee shall formulate a set of rules of procedure which, when approved by the Board, shall have the force of By-laws until revoked or amended." The policy of the Committee will be to uphold the ob-jects of -the Institute as set forth in the Constitution (Arti-cle 1, Sec. 2).

Jan 5, 1928

By Waldemar Gooskov

IN his well-known work,1 published in 1867, P. Ritter von Rittinger gives the following formula for the velocity of a particle settling in still water: v=C/D(a -1) and for average grains he assigns to the constant C a value of 2.44. As is well known, the value of C depends on the shape of the grains resulting from crushing, and it is obvious that values obtained for coal particles will not only be very different from those for ore particles but will even be characteristic of coal from a certain seam. The only way of finding an accurate value of C, applicable to conditions in Russia, where all coal-washing plants are built on German principles, is to conduct a series of tests of which the results will determine what value of C is to be used. In the investigation outlined in this paper the theories of Prof. Robert H. Richards2 were taken as the basis of the tests; the slimes were removed from the charges to eliminate the trouble of handling them; and to obtain accurate results free from errors inevitably resulting from human observation, photographic apparatus was used and a series of pictures taken which form the basis for constructing a suitable diagram of velocity vs. time.3

Jan 1, 1928

By Tadao Nagai, Masao Sato

Electrochemical measurements have been carried out in an auto- clave to investigate the electrochemistry of hydrogen precipitation of nickel from acetate buffered solution. After having previously obtained the rate equation for this reaction we have now made a concentrated effort to explain the rate equation electrochemically. A saturated NaC1-type Ag/AgC1 reference electrode has been improved so that it can be used in an autoclave. Polarization curves for the reaction, [H2=2H+ + 2e,] on nickel electrode were measured in solutions free from nickel ions at 185°C, and the parallel curves were obtained by changing PH2 and pH for normal and reverse reactions, respectively. Polarization curves in nickel solutions were complex, probably because the potential of hydrogen electrode is close to that of nickel and of the nickel surface altered during polarization. Then the nickel electrode potential and the reaction rate were measured simultaneously during pressure reduction at various hydrogen pressures and at various nickel concentrations. The reaction rates in terms of current density were plotted to obtain the local polarization curves for reactions Ni2+ + 2e ? Ni and H2 ?2H+ + 2e. The anodic and cathodic local polarization curves exhibit potential dependency. Therefore it is likely that the pres- sure reduction can be regarded as a coupled electrodes reaction.

Jan 1, 1973

By C. F. Floe, M. Cohen, M. B. Bever, V. G. Paranjpe

P. Coheur and L. Habraken—We read this paper with great interest and are glad to congratulate the authors for their valuable work, supplying an important contribution to the mechanism of tempering on the carbides in vanadium steels. We are in a good position to appreciate this work since we have been studying, for more than a year, Cr-Mo steels of a composition similar, but less highly alloyed (namely 0.1 pct C, 3 pct Cr, 1 pct Mo). Our results are quite in concordance with the authors', however, we wish to point out that it is very interesting to use equally the electron microscope in order to observe the variations of microstructure in steels. We have studied simultaneously the evolution of the carbides in situ with the electron microscope, and, after extraction, again with the electron microscope, and then with X-rays. The first results which we have obtained have been communicated at the Congress of Delft (July 1949) and at the "Journees de la Metallurgie" in Paris (October 1949). These may be summarized as follows: After tempering with varying either the tempering temperatures or the tempering times, the carbides show two evolutions. The first one is connected to the carbides existing in the steels, principally in the boundaries of the grains. For some groups of steels these carbides may coalesce and for other groups they may

Jan 1, 1951

By N. J. Grant, D. S. Bloom

P. Coheur and L. Habraken—We read this paper with great interest and are glad to congratulate the authors for their valuable work, supplying an important contribution to the mechanism of tempering on the carbides in vanadium steels. We are in a good position to appreciate this work since we have been studying, for more than a year, Cr-Mo steels of a composition similar, but less highly alloyed (namely 0.1 pct C, 3 pct Cr, 1 pct Mo). Our results are quite in concordance with the authors', however, we wish to point out that it is very interesting to use equally the electron microscope in order to observe the variations of microstructure in steels. We have studied simultaneously the evolution of the carbides in situ with the electron microscope, and, after extraction, again with the electron microscope, and then with X-rays. The first results which we have obtained have been communicated at the Congress of Delft (July 1949) and at the "Journees de la Metallurgie" in Paris (October 1949). These may be summarized as follows: After tempering with varying either the tempering temperatures or the tempering times, the carbides show two evolutions. The first one is connected to the carbides existing in the steels, principally in the boundaries of the grains. For some groups of steels these carbides may coalesce and for other groups they may

Jan 1, 1951

By D. L. Luffel

This paper presents two main developments: (1) a short, constantly accelerated centrifuge method of measuring drainage capillary pressure properties of cores, and (2) a new analytic method of treatment of centrifuge measurements to obtain saturation-capillary pressure relations. Toward the first objective, a clever experimental method is presented which is certainly more rapid than previous centrifuge methods. Toward the second objective, a new analytic method is derived to eliminate the approximate method of Hassler and runner. The derivation of this new analytic method, however, appears to be in error. The new analytic solution is developed as Eq. 5 in Appendix A. At the beginning of this derivation, the average wetting phase saturation of a core is expressed as, where is the centrifuge angular velocity. Eq. D1.2 makes explicit the dependence of S and S upon The second equation shown in Appendix A expresses the relation between the three variables Since for a given porous medium the saturation is uniquely related to capillary pressure, the functional dependence of S upon P is trivial, i.e., Pc.ri does not actually appear. Thus, the function 5 (r, ) may be expressed as a new function, S*, of PC, , alone The author transforms the variable of integration in Eq. Dl through use of Eq. D2 and writes

Jan 1, 1965

By B. Fagerberg, P. H. Fahlstrom

Crushing and grinding practice in Sweden follows closely the international pattern. Certain special circumstances, however, have had an influence on its development. Most mines are worked underground. These mines are either quite small or very large. Sulfide ores are commonly treated by custom milling and, apart from the cement industry, the rock species treated are hard and abrasive. Another important factor is the increasingly strict requirements placed on the mechanical condition of different products, especially lump ores and coarse iron-ore concentrates. Increasing requirements are being placed on the concentrate grade to suit the new steel processes. As a result, iron ore beneficiation has expanded considerably for the production of fine pelletizing concentrates. This applies especially to magnetite ores in the intermediate phosphorus range 0.1-1% P. In 1969, about 5.5 million tons of pellets will be manufactured. It should be pointed out, however, that fairly large quantities of coarse products are still being made at mills where the right conditions are available. Crushing and grinding is also of great importance in the production of rich concentrates at high recovery from sulfide ores. In fact, a large part of the development work on the concentration of sulfide ores has been devoted to the crushing and grinding processes. Boliden has played an important role in this connection.

Jan 10, 1969

By Carl Gatlin, S. Srini-Vasan

It is shown thar k k ratios cornputed on the as.sutnption that the average sandstone reservoir has a pore-size distribution characrerized by a linear 1/P saturatioN plo are in good agreewient with correspotlding k,,/k,, ratios obfairzed by Wahl, Mul-/ins and Elfrink by correlatiotz of field measurements. Methods of calculating relative permeability data have recently been reviewed and extended.' It was shown that for sandstone reservoirs where ' is approximately a linear function of effective saturation (as suggested first by Corey') it is possible to express relative permeabilities in very simple terms. For systems wetted by connate water and producing oil and gas (gas saturation growing at the expense of oil) the expression for the The accuracy of Eq. I has been frequently confirmed in our laboratories; because of its simplicity we make routine use of it in the analytical solution of proble~ns in reservoir engineering. Nevertheless, comparisons of the k,,,/k,, ratios yielded by Eq. 1 with appropriate reservoir data have been few. The publica- tion by Wahl, Mullins and ElfrinkV of an empirical equation for k,,/k,, ratios is thus of interest since this equation is specificalljl stated to be Vased on the correlation of field measurements made on sandstone reservoirs. Not surprisingly these authors found that it was necessary to