Search Documents

By D. K. Deardorff, Earl T. Hayes

An improved technique is described for the accurate determination of melting points of metals in the temperature range 1500' to 2500°C. The improvements consist of gradient heating and refinements in cavity preparation to obtain true black-body conditions. The melting point of hafnium, as determined by this method, is set at 2222°±30°C. This is over 200°C higher than one of the values reported earlier. Discrepancies in the previously reported values for the melting point of hafnium are explained. The melting points of zirconium and titanium are found to be 1855O±15OC and 1668°±10°C, respectively. Reproducibility of results was ±3OC. PRIMARILY, this report is being made to correct a 1975o±25oC1 value for the melting point of hafnium, and to present an improved method for melting point determination. As a matter of interest, the technique was also applied to determining the melting point of zirconium and titanium. There is a wide difference in the melting point of hafnium as reported by competent investigators. DeBoer and Fast' reported a value of 2230°±500C, and later work of McPherson, as reported by Aden-stedt, placed the melting point at 1975o±25oC. Zwikker" calculated that the melting point was 2430°C. In resolving this discrepancy, improvements were made in the procedure for determining the melting points of refractory metals in the range 1500" to 2500°C. Special techniques are necessary to determine the melting point of these metals accurately. Since the metals oxidize in air above 900oC, the determinations must be carried out in an inert gas or vacuum. Also, every known refractory contaminates them to some extent. In addition, the attainment of true black-body conditions is always difficult. DeBoer and Fast actually determined the melting point of Hf-Zr as-deposited iodide process alloys and extrapolated to 100 pet Hf. McPherson employed a tungsten wire suspension similar to that described by Schramm, Gordon, and Kaufmann,1 and used hafnium metal produced by the iodide process. There was no apparent reason for the wide spread in melting points, since the quality of the metal was very good and the work was under the direction of highly competent investigators. Retracing some of this work revealed one understandable error in the case of hafnium, and led to development of an improved technique for determining melting points of reactive metals in the range 1500" to 2500°C. Material Crystal bar hafnium, zirconium, and titanium were used for this work, with analyses as shown in Table I. The hafnium was of the highest purity that has been prepared, though not as pure as the zirconium and titanium. At the instigation of the Pittsburgh Area Office of the AEC, a special lot of Hfo2 was purified, converted to the tetraflouride, and bomb-reduced with calcium, all at the Iowa State College Laboratories. This crude hafnium metal was then refined by the iodide process at the Foote Mineral Co. All specimens were cut with a Sic wheel, ground, pickled, and dried carefully before use. Procedure General Tungsten Suspension Method—In this method, a small specimen is suspended by a fine tungsten wire in a slender, induction-heated tungsten or tantalum cylinder, all under vacuum. The melting point is determined by heating the specimen slowly while observing it with an optical pyrometer focused upon a portion of the specimen that radiates as a black body. This means that there should be no reflected radiation, either from colder objects near the pyrometer or from hotter surfaces. The induction heater would be the only hotter object and, if it is slender enough, the specimen will attain the same temperature. Often a slender hole is drilled into the specimen as a source of black-body radiation. This was the general method used by McPherson in obtaining his value of 1975°C for the melting point of hafnium. In trying to repeat this work, it was found that the points of contact between the

Jan 1, 1957

By J. Groyecki, M. Markuszewicz, J. Lassota, A. Zawada

The ratio of stable to unstable inclusions was found to ploy an essential role in the process of sccorldar-y recrystatlizalion in Si-Fe. The analysis of the free energy of inclusions in the range of heat-treatment of individual inclusions to be predicted. The effects MnS. ns inslable inclusions. were investigated. TO secure a high induction, the secondary recryslulliztt-lion associated wilh the texture is necessary. To obtain a low core loss an additional refiuing in the solid state is required. It has been found that sulfur can be more easily removed in racunm than in hydrogen and thai this process was hindered by the prescrzce of INCLUSIONS play an essential role in the development of cube-on-edge texture in Si-Fe. Their function consists in restraining the growth of primary grains up to about 900°C and in passing subsequently into solution at higher temperatures. This process is accompanied by the selective growth of secondary grains with (110)[001] orientation. The general effect of inclusions depends on such factors as the type of impurities, their amount. dispersion and stability, the conditions of diffusion in the space of lattice of metal, and the reactions at the metal/gas interface. In recent years, some of these factors were the subject of a special investigation. A positive influence of Mns, siN,' and vN3 has been established. The quantity of impurities4 and their dispersion5 have been found to be of major importance. Attention was called to the vital importance of diffusion and the conditions under which the impurities are removed from metal., It has also been demonstrated that in Fe-Si alloys by the techniques of powder metallurgy a special opportunity exists to obtain the (110)[001] type texture. 6 The aim of this work was to conduct qualitative investigations on the influence of inclusion stability on the development of cube-on-edge texture in a metal containing approximately 3 pct Si. Experiments were carried out on cast alloys and on those manufactured by powder-metallurgy techniques. The results obtained from these experiments were utilized to explain the phenomena involved and to analyze the relationships between stable and unstable inclusions and the magnetic properties of alloys. EXPERIMENTS AND RESULTS The raw materials used in these experiments were the powder of carbonyl iron with the analysis (in pct) 0.044 C, 0.01 Mn, 0.005 Si, 0.009 P, 0.002 S, traces of Cu, 0.06 Ni, 0.0015 Al, 0.03 Cr, 0.02 Mo, 0.01 Ti, 0.002 Co, traces of Pb, and the powder of silicon containing 94.14 Si, 0.003 S, 0.048 C. The powders were ground and mechanically mixed in 100-g batches. and then pressed at 9 tons per sq cm into 74 by 24 by 8 mm blocks. Sintering was carried out at 1100°C for 12 hr in vacuum (2 x lo-' Tr) or in hydrogen. In this instance the material was heated slowly and subjected to prolonged soaking at 350°, 650°, and 750 2C, respectively, to secure reduction of ferro-oxides. This was checked by making measurements of the dew point, which was found to change from -15" to -35°C after reduction. The compacts after sintering were hot-rolled to 2.4 mm, annealed at 800 C, and finally cold-reduced to 0.35 mm with intermediate annealing at 800°C at a gage of about 0.8 mm. Impurities were added in the powdered form and mixed with iron and silicon powders. Sulfur in the elemental state, electrolytic manganese, and pure aluminum oxide were employed. Besides, to obtain a material with low contents of impurities, especially

Jan 1, 1967

By Norman Braly

THE following is not offered as an extended paper on the subject of shaft sinking, but more as a description of the present practice of shaft sinking in the Butte district. The Anaconda company is sinking at present the following shafts: Badger State, Moose, Mountain Consolidated, Mountain View, Pennsyl-ania and Tropic. At the High Ore and Leonard mines the shafts are being deepened by sinking two compartments and will subsequently be enlarged to the full working size by raising alongside the compartments which are now being sunk. The following other companies are also sinking shafts: Butte-Alex Scott, Butte and Zenith City, Boston and Corbin, North Butte Mining Co. (at the Granite Mountain shaft), East Butte Co. (at the Pittsmont shaft), and the Rainbow Lode Development Co. Shaft Timbering. The shafts of the Butte district, generally speaking, are of three compartments arranged in a straight line, and the pump compartment is usually arranged for the use of an auxiliary hoisting cage, as well as for carrying pipe lines and electric wires. The Rainbow shaft is practically square, and of three compartments. The length of the shafts outside of timber will vary from 17 to 22 ft., and the width from 6 ft. 6 in. to 7 ft. Fir timber is used in all shaft work. This may be obtained from the Coast, when it is known as Coast fir, or from Idaho or Montana, when it is known as native fir. The native fir seems to be the tougher wood, but it is hard to obtain clear lumber in the lengths and sizes necessary for shaft work. Some of the shaft timber of the Anaconda company has been treated with creosote as a preservative, but this practice has not come into general use, as the ground of the camp is so heavy that the timbers usually crush before they rot. The size of timber most .used for shaft work is 12 by 12 in., while 10 by 12 in., 10 by 14 in. and 12 by 14 in. are used for some of the special pieces around the shaft. The new Leonard shaft is timbered with 14 by 14 in. wall plates throughout.

Jan 8, 1913

By E. R. Parker, D. L. Martin

In a previous paper one of the authors observed that the rate of cooling from the anneal prior to testing greatly influenced the life of copper under sustained load at 200°C. Furnace-cooled bars of oxygen-free copper (with and without silver) had a life four to twenty-five times that of the water-quenched specimens. The addition of 0.054 per cent silver to the oxygen-free copper increased the life at a stress of 20,000 lb. per sq. in. from about 2 hr. to 50 hr. Fractures in these bars were intercrystalline. An explanation was advanced to account for the profound influence of cooling rate on the rupture properties at 200°C. The suggestion offered was that at the high annealing temperature the minor constituents are distributed at random. By water quenching, this condition is maintained at room temperature, whereas furnace cooling permits some segregation at the grain boundaries. The higher concentration of the minor constituents in the grain boundaries results in a. strengthening, so that a longer life at a given stress and .temperature results. Small amounts of cadmium or manganese have also been found to increase the life of copper at 200°C., and to a much greater extent than silver.2 The increase in the long-time strength of copper resulting from small additions of cadmium or silver appears to be related, indirectly at least, to the higher softening temperatures of such alloys. The elements, such as silver or cadmium, which greatly increase the rupture life of copper also cause large increases in the softening temperature. As little as 0.05 per cent of cadmium or silver is sufficient to raise the softening temperature more than 100°.3,4 The effects of cooling rate and of minor constituents on the rupture properties are of considerable fundamental as well as practical interest; therefore a more detailed study of their nature was conducted and is reported in this paper. Experimental Procedure Materials The materials studied in this investigation may conveniently be classified in two groups: one consisting of a wide variety of commercial coppers, and the other composed of special high-purity, laboratory-prepared coppers. The commercial materials were tested to determine whether or not the effect of cooling rate occurred with all coppers, whereas the high-purity coppers were investigated in order to establish a basis for evaluating the effect of minor constituents on the rupture properties. In Table I are given the analyses of the coppers tested. The samples I to 6 are commercial materials and were obtained for the most part from stock supplies.*

Jan 1, 1944

By Robert Forsyth

As the latest plant on a large scale, the new Bessemer works of the North Chicago Rolling Mill Company, at South Chicago, presents some features of interest to steel-makers, I have ventured to lay before the Institute a short description of that plant, and some* remarks upon the practice there. At the time the South Chicago works were designed the adoption of the basic process in this country seemed imminent. Experience in Europe had demonstrated the perfect success of the process technically, and the question of its commercial value was one which, for any particular works, would have to be settled by its special advantages for procuring the necessary ores and basic materials. Under the circumstances, it was thought best at South Chicago to so arrange the plant as to allow the introdnction of the basic whenever it became advisable, and to make such other changes from the standard type of Bessemer plant as the state of the art seemed to demand and to foreshadow. As the use of metal direct from the blast furnace, while generally condemned by experts here, was in such successful practice in Europe (particularly in connection with the basic process), there was no doubt about its feasibility, while its economy in fuel and labor made it especially attractive to the Western manufacturer. It was accordingly decided to build a direct-metal plant adapted to the basic process. The ingots made were to be rolled into rails at one heat, and were to be of such size (12 inches square and long enough for three and four rails) as to be readily and quickly handled by the rolling machinery proposed. This small size of ingots, and the large number cast from each heat of 10 tons, made it necessary to provide a good deal of room in the casting-pit—much more than in any previons plant—and to put down extra facilities for handling ingots. To meet the delays incident to the basic process—to insure that one vessel should be always blowing if necessary, and to provide opportunity for current repairs to linings, etc.—it was decided that three vessels should be used, and, to properly concentrate the work of

Jan 1, 1884

By D. L. Martin, E. R. Parker

In a previous paper one of the authors observed that the rate of cooling from the anneal prior to testing greatly influenced the life of copper under sustained load at 200°C. Furnace-cooled bars of oxygen-free copper (with and without silver) had a life four to twenty-five times that of the water-quenched specimens. The addition of 0.054 per cent silver to the oxygen-free copper increased the life at a stress of 20,000 lb. per sq. in. from about 2 hr. to 50 hr. Fractures in these bars were intercrystalline. An explanation was advanced to account for the profound influence of cooling rate on the rupture properties at 200°C. The suggestion offered was that at the high annealing temperature the minor constituents are distributed at random. By water quenching, this condition is maintained at room temperature, whereas furnace cooling permits some segregation at the grain boundaries. The higher concentration of the minor constituents in the grain boundaries results in a. strengthening, so that a longer life at a given stress and .temperature results. Small amounts of cadmium or manganese have also been found to increase the life of copper at 200°C., and to a much greater extent than silver.2 The increase in the long-time strength of copper resulting from small additions of cadmium or silver appears to be related, indirectly at least, to the higher softening temperatures of such alloys. The elements, such as silver or cadmium, which greatly increase the rupture life of copper also cause large increases in the softening temperature. As little as 0.05 per cent of cadmium or silver is sufficient to raise the softening temperature more than 100°.3,4 The effects of cooling rate and of minor constituents on the rupture properties are of considerable fundamental as well as practical interest; therefore a more detailed study of their nature was conducted and is reported in this paper. Experimental Procedure Materials The materials studied in this investigation may conveniently be classified in two groups: one consisting of a wide variety of commercial coppers, and the other composed of special high-purity, laboratory-prepared coppers. The commercial materials were tested to determine whether or not the effect of cooling rate occurred with all coppers, whereas the high-purity coppers were investigated in order to establish a basis for evaluating the effect of minor constituents on the rupture properties. In Table I are given the analyses of the coppers tested. The samples I to 6 are commercial materials and were obtained for the most part from stock supplies.*

Jan 1, 1944

Discussion of the papers of Dorsey A. Lyon and Samuel S. Arentz, p. 789; S. E. Bretherton, p. 802; H. A. Wentworth, p. 809; and Richard D. Drvine, p. 814. GeoRge W. RiteR, Salt Lake City, Utah.—We have every reason to believe that oil flotation will soon come into general use as a final guard against slime losses in concentrating mills, not only in the case of zinc ores, but also in the case of other semi-precious ores. It also promises much as a primary process for the concentration of minerals that are not adapted to gravity methods. Moreover, modifications of the process involving selective or preferential flotation are gradually becoming understood, and will make it possible to eliminate pyrite and other minerals occurring as undesirable impurities in zinc concentrates. And what perhaps is of equal importance, further modifications promise an effective method of separating zinc blende from ores that are chiefly valuable for copper, lead, and precious metals, thereby making an asset out of zinc which has heretofore been a liability. The tendency of certain pulverized minerals to float on water, especially after having been in contact with grease, has been known to mill-men for a long time, and was formerly something to be deplored and to be striven against. All at once, this tendency has become a saving grace; and now, like tardy converts to a new faith, we are zealous advocates of something we once despised. I was once employed at a mine in the Tintic mining district of Utah— the old Eureka Hill property—where ores that were too low in value to warrant being sent to copper or lead smelters were treated in a combination mill. The ores contained gold, silver, lead, copper, zinc, manganese, arsenic, etc., in varying quantities and in varying mineral forms, mingled in a quartz and calcite gangue. The material was stamped fine and then concentrated on Frue vanners so as to make a smelting concentrate, after which the tailings were thickened and treated in amalgamating pans for the recovery of non-concentratable precious metals. In the amalgamating pans, under the influence of heat and agitation, a dark greasy froth or scum sometimes formed on the surface of the ore mixture. This froth or scum was composed mainly of mineral sulphides, and its occurrence might have meant only casual losses in the previous concentration, except that the phenomenon was accompanied by faulty amalgamation of the precious metals and by excessive losses in the mill tailings. Grease and oil, present by accident, were the cause of the trouble. Whether the intense vibration in the mill, due to the pounding of the heavy stamps, had caused small particles of grease to be shaken loose

Jan 1, 1915

LIST OF MEMBERS AND ASSOCIATES ARRANGED ACCORDING TO STATES AND TOWNS ALABAMA Aldrich, Aldrich, W F Anniston, Noble, A E, Smith, N B Aibacoche, Bradley, D II Bessemer, Fergusson, V Birmingham, Aldrich, T H, Aldrich, T H, Jr, Bowron, J, Bowron, C E, Davis, F H, Dimmick, F D, Hillman, McCarthy, M E , McCormack, McCrery, Ramsay, E, Shook, A M Bridge¬port, Wheeler, S K Ensley, McDonald, S, Shook, J W Fanbanks, Hamil¬ton, A L Helena, Squire, J Huntsville, Moss Lehigh, Toulmin Oxmoor, Green¬amyer, A G Plasma, Gage Rock Run, Garvin Sheffileld, Miller, D I Tuscaloesa, Lodge, J University, McCalley Woodward, Bukofzer, Woodward, A H ALASKA Dawson, Buck Douglas Island, Corbus, J P , Macdonald, J Hames, Le Wald, E A Jualin, Hoggatt, W B Juneau, Denby, Gaifield, Garside, Hamp¬ton, W H Rodman Bay, Phillpots Snettisham, Tisdale Sumdum, Thane Tel¬ler, Hirshberg, M R Treadwell City, Batcheller, J H , Kinzie Valdez, Esterly, G M Yukon, Dawson, Elmer, J M ARIZONA Bisbee, Clark, G C, Coombs, H L , Douglas, W, Hoatson, Parnall, S A, Pelton, R T, Ricketts, L D, Sherman, G F G, Smith, F W, Smith, H A Black Diamond, Bagge Blanchard, Cummins, Murray, J J Casa Grande, Rich¬mond, A B Clifton, Colquhoun, Grabill, Murray, H T , Plater, Smith, J D A, Veitch, Watson, W S Congress, Goodloe Crown King, Alexander, G E Douglas, Cornell, Kraemer, E L, Lee, G B, Rutherford, F Globe, Berray, Hoar, Snell Harrisburg, Smith, F C Jerome, Clark, W A, Thomas, C A Kingman, Treadwell, Wallace, J P Kirkland, Bretherton, G K Kofa, Lamp¬shire, J O , Pomeroy, H G Mayer, Haggott, E A Metca j, Blumenkranz, M , Forbes, D L H Morenca, Clark, C D, Fleming, J B, Honey man, Mills, C E, Wallace, L R Morristown, Stevens, H W Nogales, Glove, H G, Sandoval, A , Sandoval, P Octave, Rose, G W Phoenix, Armstrong, T , Butler, C E, Defty, Lindsay, L Prescott, Blauvelt, H , Bunker, C E, Claypool, W M , Drescher, F M , Fairbank, Nissen Tombstone, Gage, Poindexter, C L , Staunton, Walker, E W Troy, Cutting Tucson, Blake, W P, Burgess, De Lashmutt, I, McCleary, Mann, Prout, J W , Jr ARKANSAS Fayetteville, Purdue Fort Smith, Bache, F , Denman, H Little Rock, Fordyce, Scholz CALIFORNIA Alameda, Arents, King, L Arnador City, Downs, Tregloan Angeles Camp, Dig¬gles, R N , Kenney, C E Antioch, Belshaw Auburn, Coe, I J Ballarat, Thorns Berkeley, Abadie,, Christy, Dozier, Hall, F F , Hersam, Landfield, Lind¬say, L , Mansfield, N T, Morley, W S , Sharwood, W J Bag Oak Flat, Dron Bodae, Hamilton, W R, Hoover, T, Hoover, T J, Jackson, B L , Nutter , E, H Bullion, Power, H T Callahan, Scott, E H Campo Seco, Baird Cartero,

Jan 1, 1910

By J. D. Prater, H. R. Spedden, E. E. Malouf

With the expansion of copper leaching of the various mine wastes at the Kennecott properties, additional copper recovery facilities have been required. A research and development program has been pursued to determine a suitable economic approach to the processing of the additional leach solutions contemplated. lnvestigations on laboratory and pilot plant scales covered electrowinning, solvent extraction, launder and vat type cells, activated launders, precipitation drums, and precipitation cones. This paper contains information on the development and use of a new precipitation-cone-type copper recovery plant, which provides many advantages over older systems. The application of research findings to the old art of leaching copper from copper-bearing mine waste has resulted in a significant contribution of copper to over-all copper production. For example, at the completion of the current expansion program at the Kennecott properties in the United States, copper produced from waste dump leaching will amount to about 25% of the total production. Formerly only 2% was derived from this source. This planned expansion of copper leaching focused attention on the problem of developing more efficient methods for the recovery of copper from greatly increased volumes of copper-bearing solutions.1 The detailed investigations which have been made in laboratory pilot plant and plant tests for the recovery of copper from copper-bearing solutions have included electrowinning, solvent extraction, ion exchange and cementation with iron in launders, precipitation drums, activated launders, and precipitation cones. The results of these investigations have led to the development of a new precipitation cone-type copper recovery system providing many advantages over older methods. ELECTROWINNING OF COPPER FROM COPPER-BEARING SOLUTIONS The direct electrowinning of copper from relatively dilute solutions of copper-bearing mine water, namely solutions containing 10 to 20 lbs of copper per 1000 gal, has always been an attractive possibility.2,3 By this method, high-purity copper powder can be recovered with a power consumption of 3.5 kwh per Ib of copper. However, once the solution strength de-

Jan 1, 1967

By T. L. McCall

THE late Walter Herd1 in 1929 gave a full description of past and present conditions in No. 2 mine, Springhill, Nova Scotia, developed theories regarding the cause of these bumps and made certain suggestions regarding possible methods of future development. Recapitulating briefly from Mr. Herd's paper, the seam is bituminous coal, averages 9 ft. in thickness and has a well defined parting containing fusain about 14 in. from the roof. This roof coal is somewhat stronger than the rest of the seam and has a tendency to cling to the roof. The pitch of the seam where it is now being worked is about 20°. The first manifestations of bumps began when the room and pillar workings had reached a depth of cover of 1900 ft. and under continuously increasing depth of cover these bumps increased to such an extent, both in number and severity, that in the year 1924 it became apparent that some change in the system of extraction was necessary. After closely studying all the factors involved and benefiting largely by valuable out-side advice obtained by the Provincial Department of Mines of Nova Scotia,2 the system of working was changed from room and pillar to longwall retreating. Mr. Herd's paper described in detail three remarkable bumps in the year 1928 in April, July and October that affected the 5700-ft. and 5900-ft. East levels, the last bump being so severe both in intensity and in extent of damage done that this district was abandoned. The longwall workings to the west of the slope had been stopped in the year 1926 owing to an inbreak of water, coming from the flooded waste of No. 3 seam lying some 400 ft. vertically overhead. This inflow was not excessive, but a large quantity of water being impounded in the old workings it was considered advisable to take the prudent course and not incur the risk of possibly increasing the flow by further working. This district has remained idle ever since.

Jan 1, 1934

By J. A. Herrick

For a long time, especially in Europe, heavy pieces of forging, such as cannon, armor plates, marine shafting, etc., have been steadily augmented in size, more particularly since steel has been substituted for wrought iron. To keep pace with these forgings several very large hammers have been, from time to time, erected. The most powerful and thoroughly appointed of all now in operation is that designed and built by Messrs. Schneider & Co. at their' works at Creusot, and it is the design of this communication to give to the members of the Institute a concise description of this remarkable piece of mechanism, which I have taken from an article published in the Annales Industrielles. This hammer is rated nominally at 80-tons power, but its capacity is, in reality, far greater, as will be seen by the comparative figures given later. The complete plant, comprising the hammer, the cranes, the furnaces, and the building which shelters the whole, is distin-

Jan 1, 1880

By J. A. Herrick

FOR a long time, especially in Europe, heavy pieces of forgings, such as cannon, armor plates, marine shafting, etc., have been steadily augmented in size, more particularly since steel has been substituted for wrought iron. To keep pace with these forgings several, very large hammers have been, from time to time, erected. The most powerful and thoroughly appointed of all now in operation is that designed and built by Messrs. Schneider & Co. at their works at Creusot, and it is the design of this communication to give to the members of the Institute a concise description of this remarkable piece of mechanism, which I have taken from an article published in the Annales Industrielles. This hammer is rated nominally at 80-tons power, but its capacity is, in reality, far greater, as will be seen by the comparative figures given later. The complete plant, comprising the hammer, the cranes, the furnaces, and the building which shelters the whole, is distin-

Jan 1, 1880

By R. Woodward Moore

A graphical method of analyzing the data obtained from shallow earth-resistivity depth tests is presented. The method is based upon empirical results and has no theoretical basis. The usual apparent resistivity-electrode spacing curve is used together with a cumulative resistivity-electrode spacing curve plotted on the same sheet. The greatly reduced scale required for plotting the cumulative values of resistivity together with the effect of the summation of the individual resistivity values serves to minimize the effect of purely local surface anomalies and inadvertent errors of measurement. The point of intersection of tangents or straight lines drawn to intersect at zones of maximum curvature in the cumulative curve indicates the depth to the underlying material. Numerous figures are presented in which data from published reports and from recent field studies are analyzed and the results compared with actual depths established by borings or with depth values obtained by the use of theoretical methods of analysis. Smoothly rounded curves of apparent resistivity such as are often obtained in the field, and which have been a serious drawback to attempts to analyze the data empirically heretofore, appear to be susceptible to rather accurate analysis by the method described. The method is best suited to analyses involving shallow two-layer formations. It has been applied successfully, however, in analyzing the data obtained from tests made over shallow three-layer formations. As with most empirical methods, its chief advantage is its simplicity and ease of application. There have been published many papers that discuss the interpretation of data obtained from earth-resistivity tests when using the four-terminal method of electrode spacing developed by Wenner.' The majority of these have dealt with theoretical analyses for two-layer and three-layer formations. Some sets of "master curves" have been presented for use in analyzing field data to determine the depth to the first and possibly the second horizon below the earth's surface. Although practically all of these theoretical methods of analysis have appeared to have particular merit and some have been used successfully in practice, they have been found to be of little value where the local conditions surrounding the test failed to conform to those assumed in the theory. In certain fields, particularly in civil engineering, relatively shallow explorations are often involved and geophysical methods of test must compete with the direct methods of exploration ordinarily used. Only when it can be demonstrated that geophysical methods of test can materially reduce the time and cost of a given exploration project will the civil engineer abandon direct methods in favor of the interpretations of geophysical exploration data. Empirical methods of analyzing earth-resistivity data have been used in many instances in the past. Such methods have been employed for a number of years by the Public Roads Administration in research work relative to the application of

Jan 1, 1946

By R. Woodward Moore

A graphical method of analyzing the data obtained from shallow earth-resistivity depth tests is presented. The method is based upon empirical results and has no theoretical basis. The usual apparent resistivity-electrode spacing curve is used together with a cumulative resistivity-electrode spacing curve plotted on the same sheet. The greatly reduced scale required for plotting the cumulative values of resistivity together with the effect of the summation of the individual resistivity values serves to minimize the effect of purely local surface anomalies and inadvertent errors of measurement. The point of intersection of tangents or straight lines drawn to intersect at zones of maximum curvature in the cumulative curve indicates the depth to the underlying material. Numerous figures are presented in which data from published reports and from recent field studies are analyzed and the results compared with actual depths established by borings or with depth values obtained by the use of theoretical methods of analysis. Smoothly rounded curves of apparent resistivity such as are often obtained in the field, and which have been a serious drawback to attempts to analyze the data empirically heretofore, appear to be susceptible to rather accurate analysis by the method described. The method is best suited to analyses involving shallow two-layer formations. It has been applied successfully, however, in analyzing the data obtained from tests made over shallow three-layer formations. As with most empirical methods, its chief advantage is its simplicity and ease of application. There have been published many papers that discuss the interpretation of data obtained from earth-resistivity tests when using the four-terminal method of electrode spacing developed by Wenner.' The majority of these have dealt with theoretical analyses for two-layer and three-layer formations. Some sets of "master curves" have been presented for use in analyzing field data to determine the depth to the first and possibly the second horizon below the earth's surface. Although practically all of these theoretical methods of analysis have appeared to have particular merit and some have been used successfully in practice, they have been found to be of little value where the local conditions surrounding the test failed to conform to those assumed in the theory. In certain fields, particularly in civil engineering, relatively shallow explorations are often involved and geophysical methods of test must compete with the direct methods of exploration ordinarily used. Only when it can be demonstrated that geophysical methods of test can materially reduce the time and cost of a given exploration project will the civil engineer abandon direct methods in favor of the interpretations of geophysical exploration data. Empirical methods of analyzing earth-resistivity data have been used in many instances in the past. Such methods have been employed for a number of years by the Public Roads Administration in research work relative to the application of

Jan 1, 1946

By A. Keil

TO measure the absolute conductivity of metallic specimens it is generally necessary to have exact geometrical shapes and good electrical contact with the test-piece. To overcome limitations of the standard methods, an electronic conductivity-meter* Trade name, Sigmatest; model Dr. F. Forster; Reutlingen, Ger-many. has been developed, which works on the principle of inducing high frequency eddy-currents in the specimens and measuring the reaction of these curients on a measuring coil.',' To attach the instrument to the test specimen, a flat area of about 10 mm diam is all that is necessary. The reading is taken off a scale calibrated in pet of International Annealed Copper Standard. The induced eddy-currents are propagated in a circular motion parallel to the surface. Thickness of the layer included in a measurement depends on the frequency used. With a frequency of 60 kc per sec, the penetration of the currents was 0.8 mm at the upper limit of the scale, and 2 mm at the lower limit. The method is limited to nonferrous metals and other applications have been described elsewhere." The object of the present investigation was to detect the formation and growth of surface layers of differing conductivity, and to determine the depth to which these changes could be observed. A well known phenomenon which illustrates the problem is the internal oxidation of certain silver alloys containing base metal solutes, such as copper or cadmium, when they are annealed in an oxidizing atmosphere.4, 5 Until now, the only methods available for following these phenomenon have been metallo-graphic examination and hardness tests.0, 7 Changes in mechanical properties of copper alloys by internal oxidation were recently discussed in a more general way by Martin and Smith." When measuring these conductivity changes it must be remembered that the only absolute values of conductivity are those of 1) the nontreated homogeneous specimen, and 2) the final values obtained with a surface layer of depth comparable to the penetration of the eddy-currents. All intermediate values refer to the mixed conductivities of the transformed surface layer and the untransformed alloy, and are thus readings of relative value only. Experimental Results Specimens were annealed for 1/2 hr at 800°C in hydrogen, and the internal oxidation was carried out by thermal treatment in air at 800°C. Fig. 1 shows the results of the first series of experiments. With internal oxidation of a solid solution of 8 pet Cd in silver, the conductivity rises continuously until the surface layer formed has become thick enough to be the deciding factor (about 400µ). Precipitates of CdO are mainly in the form of points, Fig. 2, and, as a result, the electric contact between the silver crystals is not distorted by them. Brine11 tests were run with a 1.25 mm ball and a 7.812 kg load. The specimen annealed in hydrogen and oxidized to a depth of 400µ had a hardness of 40 Bhn,

Jan 1, 1959

By T. E. Leontis

The importance of magnesium alloys in the manufacture of aircraft engines has been realized for many years. A concentrated effort has been exerted in the laboratories of the Dow Chemical Co. to develop magnesium-base alloys with improved properties at elevated temperatures whereby greater advantage can be taken of the inherent lightness of these materials. In an earlier publication, attention was called to the superior tensile properties and resistance to creep of cerium-containing magnesium alloys at temperatures up to 700°F. More recently, additional data on magnesium-cerium alloys have been furnished by Murphy and Payne. The present paper deals with the mechanical properties of sand-cast magnesium alloys containing zinc, at temperatures up to 500°F. The study includes binary Mg-Znt alloys containing up to 10 pct zinc and several ternary and some polynary alloys based on the Mg-~Zn,f Mg-jZn, Mg-4.4211, Mg-6Zn, and Mg-roZn binaries. The compositional variation in the tensile properties, hardness, and creep at room and elevated temperatures, and in the electrical conductivity at room temperature has been determined. The results of these tests show that many zinc-containing magnesium alloys exhibit resistance to creep at elevated temperatures significantly higher than that of present commercial magnesium alloys, but lower than that of alloys of the magnesium-cerium type. In addition, they have high tensile properties at room and elevated temperatures and high conductivity. This combination of mechanical properties and conductivity indicates that these alloys should be given serious consideration for commercial applications involving exposure to temperatures higher than those to which present commercial magnesium alloys can be taken safely. Literature The properties of sand-cast magnesium alloys containing zinc as a principal alloying element have not been investigated very extensively, especially at elevated temperatures. The following remarks, which are confined to sand-cast alloys, will serve as a summary of the most important references on this phase of magnesium metallurgy. The first recorded determination of the tensile strength of binary Mg-Zn alloys as a function of zinc content was reported by Aitchison. Similar studies, including the measurement of elongation and hardness, have been performed by Gann and Winston,' Dumas and Rockaert, Haugh-ton and Prytherch,6 and by Spitaler, the last being reported by Beck.' A slight superiority in the tensile strength of chill-cent Mg + 8 es alloy Over the sand-cast alloy was noted by Maybrey.8 That alloys of magnesium containing 5 to 12 pct zinc

Jan 1, 1949

By Reuel A. Cochrane, Harry H. Angst

The successful exploitation by opencut methods of the low-grade porphyry copper deposits is due to the economical handling of large tonnages. Large tonnages are possible only if the rock material is broken so that the large power shovels can operate with minimum delays. This is particularly true at the New Cornelia mine, where the dense, hard, tough rock material creates problems not encountered in most of the porphyry copper mines. The introduction of churn drills at the New Cornelia for primary drilling, in 1936, necessitated a complete change in the methods of breaking ground as formerly air drills had been used. The blasting operations are of particular interest because of the handling of great quantities of high explosives in safely and efficiently fragmenting the hard rock material. Rock Formations At the New Cornelia mine the rocks are quartz monzonite with a diorite border facies intruding a rhyolitic series. Overlying these formations is a fanglomerate formation composed of boulders of monzonite, diorite, rhyolite, and other types of rock of unknown derivation. (The word "fanglomerate" is used in this paper in referring to the local conglomerate type of rock formations.) The ore body is approximately 4800 ft. long and 2800 ft. wide, and is of the disseminated type. Mineralization occurs principally in the quartz monzonite and to some extent in the adjacent diorite and rhyolite. The principal ore minerals are chalcopyrite, bornite, and a small amount of chalcocite. Over a considerable area the quartz monzonite is extremely hard and siliceous in character, owing to pegmatitic zones of alteration. The hardness of the ground depends on the intensity of the silicification. In a small area in the pit, the monzonite contains an abundance of pyrite accompanied by sericitization and is soft and easily fragmented. This is true also in the remaining oxidized portion of the ore body. The diorite and rhyolite formations, like the monzonite, vary from extremely hard to very soft material, but on the whole are easier to fragment than the monzonite. Jointing is prevalent in all the rock formations and plays an important role in the blasting efficiencies. In the fanglomerate formation, numerous well-defined joints, widely spaced, tend to make the ground blocky when blasted. This is a deterrent to good fragmentation. In the other rocks the joints are more numerous and are closely spaced, except in localized areas where the formations are extremely hard. These descriptions indicate that the lowest blasting efficiency will be obtained in the harder formations, from which the major portion of the mine production is obtained; namely, the monzonite and rhyolite. All rock formations mined at the New Cornelia pit are so hard that excavation

Jan 1, 1943

By Harry H. Angst, Reuel A. Cochrane

The successful exploitation by opencut methods of the low-grade porphyry copper deposits is due to the economical handling of large tonnages. Large tonnages are possible only if the rock material is broken so that the large power shovels can operate with minimum delays. This is particularly true at the New Cornelia mine, where the dense, hard, tough rock material creates problems not encountered in most of the porphyry copper mines. The introduction of churn drills at the New Cornelia for primary drilling, in 1936, necessitated a complete change in the methods of breaking ground as formerly air drills had been used. The blasting operations are of particular interest because of the handling of great quantities of high explosives in safely and efficiently fragmenting the hard rock material. Rock Formations At the New Cornelia mine the rocks are quartz monzonite with a diorite border facies intruding a rhyolitic series. Overlying these formations is a fanglomerate formation composed of boulders of monzonite, diorite, rhyolite, and other types of rock of unknown derivation. (The word "fanglomerate" is used in this paper in referring to the local conglomerate type of rock formations.) The ore body is approximately 4800 ft. long and 2800 ft. wide, and is of the disseminated type. Mineralization occurs principally in the quartz monzonite and to some extent in the adjacent diorite and rhyolite. The principal ore minerals are chalcopyrite, bornite, and a small amount of chalcocite. Over a considerable area the quartz monzonite is extremely hard and siliceous in character, owing to pegmatitic zones of alteration. The hardness of the ground depends on the intensity of the silicification. In a small area in the pit, the monzonite contains an abundance of pyrite accompanied by sericitization and is soft and easily fragmented. This is true also in the remaining oxidized portion of the ore body. The diorite and rhyolite formations, like the monzonite, vary from extremely hard to very soft material, but on the whole are easier to fragment than the monzonite. Jointing is prevalent in all the rock formations and plays an important role in the blasting efficiencies. In the fanglomerate formation, numerous well-defined joints, widely spaced, tend to make the ground blocky when blasted. This is a deterrent to good fragmentation. In the other rocks the joints are more numerous and are closely spaced, except in localized areas where the formations are extremely hard. These descriptions indicate that the lowest blasting efficiency will be obtained in the harder formations, from which the major portion of the mine production is obtained; namely, the monzonite and rhyolite. All rock formations mined at the New Cornelia pit are so hard that excavation

Jan 1, 1943

By M. R. Geer, H. F. Yancey

With the exception of pneumatic processes and a few special beneficiation methods of comparatively limited application, all mechanical coal-cleaning and mineral-dressing processes involve the admixture of solid particles with a liquid, generally water. Upon completion of the beneficia-tion process the solids must be reclaimed from the water. With coarse particles separation of solids from water is accomplished readily by the simple expedient of screening, but recovery of fine solids presents a much more difficult problem. Thickening and dewatering are practiced so generally, both within the mineral industry and elsewhere, that they have been the subject of study through the years and a number of processes for making the solid-liquid separation have been developed. Dorr-type thickeners have been standard equipment lor many years, and more recently driers employing centrifugal force have gained in popularity.' A cyclone device employed to thicken the loess suspension is a novel feature of the loess heavy-medium coal-cleaning process developed by the Netherlands State Mines in the thirties. The cyclone thickener was first mentioned by Driessen2 in 1939 in a paper describing the loess process and has been the subject of two more recent reports by the same author.3 The cyclone does not differ greatly from cyclone dust collectors used in this country for years, except that it is operated wet rather than dry. Advantages of the cyclone over other thickening devices are its simplicity of construction, high capacity, and the fact that, having no moving parts, it is simple and inexpensive to operate. The Bureau of Mines became interested in the cyclone after one of the present authors observed it in operation in the Netherlands in 1945. The first experimental work with the cyclone conducted by the Bureau of Mines was an investigation of the unit functioning as a heavy-medium cleaner for fine coal—a use for the cyclone that was conceived long after it had been perfected as a thickener. The results of this investigation were published last year.4 The present investigation deals exclusively with operation of the cyclone as a thickener. Object and Scope of Investigation Although the cyclone thickener has been dealt with in three reports by Driessen, its use as a thickener was not the principal subject of any of these reports and therefore neither the cyclone itself nor its operation was described completely. The design of the cyclone was described only in a very general way, only limited operating results were given, and virtually nothing was disclosed about the influence of the various possible operating variables. Moreover, the Netherlanders apparently had employed the cyclone exclusively for thickening loess and had not employed it On coal 'lurries. One English colliery has used a cyclone to thicken coal slurry,5 and as it appeared that

Jan 1, 1949

By R. G. Bowman

Discussions of processes for the manufacture of white lead generally open with the statement that white lead is the oldest chemical pigment known to man. This fact is of more than historical interest; in the light of the present extensive use of white lead, it indicates that the compound possesses characteristics that make it unique among white pigments, and superior to all in its particular field. A greater variety of processes have been proposed for manufacturing white lend than for any other one chemical compound. Only a few of these processes have come into commercial use, however, and a large part of the present production here and abroad is made by the process used in ancient times. The outstanding disadvantages of the old process are that it is slow and laborious, affords no control of the product, and yields at best an impure material lacking in uniformity. Improved processes, sometimes classed all together as "quick processes," have had as their main object the shortening of the time required. Most of them accomplish this and some have yielded a superior product as well, but only two or three are now in use commercially. For centuries the manufacture and mixing of paints have been treated as an art, and the practice has been much influenced by tradition and precedent. There is a reluctance to abandon old materials for this purpose, and as few new uses for white lead have been developed, the adoption of the quick processes has been slow. The electrolytic production of white lead is not new, a large number of processes and forms of apparatus have been proposed and patented within the past 25 years, all directed toward the production of white lead, wholly or in part, by electrolysis. One or two of these processes were tried commercially but proved unsuccessful. Process The Sperry process, used by the Anaconda Lead Products Co., is the invention of Elmer A. Sperry, and was worked out to a commercial basis at the East Chicago plant. It resembles, in a general way, earlier methods, but embodies the features that make it possible to operate

Jan 1, 1926