Search Documents

By H. R. Skewes

IN the course of small seale experiments on the electrodeposition, of copper, extremely brittle deposits were obtained from electrolytes prepared by leaching calcined chalcopyrite with aqueous sulfuric acid. It was not possible to strip the metal without fracture after it had been deposited from such electrolytes onto smooth oiled copper sheets, the usual plant procedure for the production of so-called starting sheets. The embrittlement did not occur with electrolytes made either by leaching the calcine with water or by treating an acid leachate to remove iron as hydrous ferric oxide. The electrolytes which produced brittle deposits were found to contain molybdenum in concentrations of 10 to 25 mg per 1, whereas those which produced ductile deposits contained <0.5 mg per 1. Synthetic electrolytes having the composition: Cu", 40 gpl; Fe", 0.5 to 1.0 gpl; Fe3+, 0.5 to 1.0 gpl; and H,SO,, 10 to 50 gpl, were prepared from reagent-grade salts; by adding ammonium molybdate, the embrittling effect of the higher concentrations of molybdenum (VI) was strikingly confirmed. The brittle deposits contained up to 0.03 pct Mo. The importance of oxidation state of the molybdenum was demonstrated when the electrolyte containing it was circulated continuously through a bed of fine copper metal during deposi- tion. Under these reducing conditions, the cathode deposit was ductile and molybdenum could not be detected. Molybdenum has not been recognized as one of the metals causing embrittlement of copper nor is it listed among the usual impurities. In most elec-trowinning plants there is a purification step which removes iron from the leachate before electrolysis. In these cases molybdenum would be coprecipitated with hydrous ferric oxide. In the case of the large leaching plant at Chuquicamata, Chile, where the leachate is reported to contain considerable molybdenum, it would be reduced to a lower oxidation state during removal of chlorine by means of cement copper. This may explain why the embrittling effect of molybdenum has not been reported previously. Moreover, in copper refining plants where soluble anodes have been prepared by a high temperature smelting process, it is most unlikely that any molybdenum would remain with the copper, whereas the calcines in this work were prepared in a fluidized bed reactor at a temperature not exceeding 720°C. Acknowledgment This work is part of an investigation on the roasting and extraction of copper from sulfide ores sponsored jointly by Mt. Morgan Ltd., Queensland, and the Mt. Lyell Mining and Railway Co. Ltd., Tasmania.

Jan 1, 1958

By G. B. Misra

Though resistance to flow offered by mine airways supported with timber sets has been an object of study over the last half century, no accurate relation has yet been established from which prediction of the resistance coefficient of a projected timbered airway can be made. Zenofontowa et al. developed an empirical relation, but this relation has not been found to satisfactorily correlate experimental data obtained by Sales and Hinsley. This led the author to develop a set of simple theoretical relations between the resistance coefficient of timbered airways and the various parameters affecting it, such as the type and spacing of sets as well as the shape and size of members forming the set. Experiments were designed with the help of a laboratory model airway to verify the validity of the relations developed. With the experiments conducted so far with 4, 3 and 1-piece sets of 3.4 x 3.4, 2..5 x 2.5, and 4.5 X 4.5-cm square-section timbers in a 45.8 x 38-cm model airway, the theoretical relations have been shown to hold.

Jan 1, 1972

By C. F. Cockrell, H. E. Shafer, J. W. Leonard

A significant technological development is discussed for the processing of certain power plant flyashes that are a problem because they contain a high water-soluble mineral content and yield inferior flyash-based brick. This development is based on the addition of hydrochloric acid to the flyash-bottom ash-sodium silicate blends used for the production of flyash-based structures. Favorable changes are evi-dent in sodium silicate consumption, where about half the amount used for making brick from normal flyash is required, processing costs, and strength and appearance of the resulting freshly formed green and fired structural products. In some high cost in-stances (above the $30 or less per thousand brick estimated for normal flyash), hydrochloric acid additions can replace or reduce other costly additives normally required for problem flyashes. This results in savings of as much as $9 per thousand brick. These developments offer promising possibilities for utilizing problem flyashes as well as flyashes which may come into contact with water soluble sulfur as a result of the eventual application of certain experimental air pollution control processes. Much of the research datal-6 accrued through work by the Coal Research Bureau of West Virginia University for the Department of Interior&apos;s Office of Coal Research on converting waste power coal ash to valuable brick and other structural products, can be categorized as follows: (1) general ash-to-brick tech- nology; (2) specific ash-to-brick optimization; (3) pilot plant progress; (4) production cost estimates. A summary of the progress on bench-scale experiments indicates that coal ash can yield two types of brick. An acceptable brick is obtained by mixing 73.6% fly-ash, 23.5% bottom ash and 2.9% sodium silicate solution (dry basis). Depending on the flyash and bottom ash used, optimum brick can be manufactured by mixing 72-77% flyash, 20-25% bottom ash and 2.3-3.0% sodium silicate (dry basis) with Na2O : SiO2 ratio varied according to the composition of the flyash used. These blends are thoroughly mixed and mechanically formed into green brick shapes at pressures ranging from 1000 to the more usual 3000 lb per sq in. The green shapes then are dried and fired at temperatures ranging from 1975-2150°F using clay brick cycles that are shorter than standard. Other findings reported to date indicate that when making optimum brick, it is necessary to carefully control the top size of the moisture-releasing bottom ash so that it falls between 8 and 30 mesh, depending on the flyash used. Moreover, the chemical composition of bottom ash and flyash have been found to be of little significance with the exception of a few problem flyashes which are the subject of this paper. Finally, the pilot plant, which was previously reported under construction, is now in operation. This will indicate, among other things, the cost of brick production, which was earlier estimated for non-problem flyashes at $30 or less per thousand brick. The foregoing bench-scale technology is applicable to all the initially tested ashes as well as to the majority of ashes examined during the course of research. However, a few of the ashes yield green and fired products that may be structurally inferior or unacceptable, necessitating excessive and diverse reagent addition, and/or may be coated with unsightly surface deposits. These problem ashes generally originate in certain areas of Illinois, western Ken-

Jan 1, 1969

By William B. Phillips

The possible sources of potash salts in the United States have been considered from many points of view during the last several years, but it is only within the last two or three months that the situation has become acute. We import from Germany, the only sourcc of large supply, more than $10,000,000 worth of potash salts annually, and this business has been badly crippled by the European war. If there was ever a time in our industrial existence when the necessity of providing for our own needs was more acute than it is now, we are not aware of it. One has only to study the price lists of chemicals sent out by the large supply houses to see the change wrought within a very short time. Whether or not these prices are to maintain for a considerable time, no one can say; but it appears to be probable that we shall not see prices materially lower for a period of uncomfortable length, to say the least. It is not my purpose at this time to discuss the various sources of supply of potash salts that have been suggested or recommended. Some of them might afford a pleasing relief but all of them combined would not affect the situation seriously. If we are to have our own sources of potash salts, they will have to compare, in some efficient manner, with the sources upon which we have drawn during the last 20 or 30 years; i.e., they must exist in minable quantities. It seems to me to be quite idle to speculate upon our domestic sources of potash if those sources are not of a character similar to those upon which we have so long depended. A few thousand or, perhaps, a few hundred thousand dollars&apos; worth of chemically derived potash may be produced under the stress of present conditions, but when we consider that each year demands more than $10,000,000 worth, we must look to underground sources; we must look to mines similar to the famous Stassfurt and Halle deposits. If we cannot mine potash salts, we shall have to do without them for a while.

Jan 1, 1915

By R. A. Morse, P. M. Bridges, L. E. Wilsey, Howard N. Hall, P. L. Terwilliger

Theoretical and experimental investigations of a constant pressure gravity drainage system are reported. Experimental data are presented to show that recovery to gas breakthrough by gravity drainage is inversely proportional to rate. The gravity drainage reference rate, which is numerically equal to the so-called "maximum theoretical rate of gravity drainage" is shown to have no particular significance from a recovery standpoint. Before this rate can be used as a basis of comparison for recoveries, it is necessary that the relative permeability and capillary pressure characteristics and displacing fluid viscosities be identical for the systems compared. A method is presented by which accurate prediction of the performance of a gravity drainage system can be made. Close agreement between experimental and calculated drainage performance shows that steady state relative permeability and static capillary pressure data can be used to describe fluid displacement behavior. The very wide range of liquid recoveries before gas breakthrough which result from production rate variation alone demonstrates the importance of this factor in planning depletion of a gravity drainage reservoir. Calculated results are presented which show that little additional recovery can be expected from a high pressure gravity drainage system between the times of gas breakthrough and attainment of such high gas/liquid ratios as to make further pressure maintenance impractical. INTRODUCTION It bas been recognized for some time that gravity forces play an important part in the recovery of oil from some types of reservoirs. Field experience has shown that under certain conditions, gravity drainage can result in very high oil recov- eries. Qualitative reasoning has led most engineers to the general conclusions that: (1) Where gravity drainage is important, the reservoir pressure should be maintained by gas injection at the crest of the structure to prevent shrinkage of the oil in place and to keep a low viscosity so the oil can drain at the fastest possible rate. (2) Recovery by gravity drainage is rate sensitive. A survey of the literature indicates that while considerable work has been done on the effects of gravity in oil production problems, no satisfactory method of calculating the performance of gravity drainage reservoirs has been reported.1,2,3,4,5 In the absence of any proven method of calculating reservoir performance, the level at which pressure should be maintained and the rate of production for most efficient operation has been open to debate. The limits and general character of the recovery us rate relationships are apparent from the following: As rates of production approach zero, oil will drain by virtue of its own weight fast enough that the saturation distribution is always approximately the same as the original static capillary distribution. That is, at the gas-oil contact the liquid saturation goes from 100 per cent to a value of perhaps 10 to 30 per cent in a very short distance, so that as production continues. a relatively sharp gas-oil contact moves down-structure, leaving a very low residual oil saturation in the originally oil saturated zone. At very high rates of production, the oil that drains by virtue of its own weight is negligible and recovery will approach that of a horizontal gas drive, leaving a much higher residual oil saturation. At intermediate rates of production. recovery should be between these extreme*. Despite the lack of quantitative methods, tentative agreement had been reached on the question of optimum producing rate. It has been generally concluded that rather sharp decrease in recovery would occur at rates of production above the "maximum rate of gravity drainage" and hence this rate should not be exceeded. The "maximum rate of gravity drainage" is defined as the rate of production from a 100 per cent

Jan 1, 1951

By L. E. Wilsey, R. A. Morse, P. L. Terwilliger, Howard N. Hall, P. M. Bridges

Theoretical and experimental investigations of a constant pressure gravity drainage system are reported. Experimental data are presented to show that recovery to gas breakthrough by gravity drainage is inversely proportional to rate. The gravity drainage reference rate, which is numerically equal to the so-called "maximum theoretical rate of gravity drainage" is shown to have no particular significance from a recovery standpoint. Before this rate can be used as a basis of comparison for recoveries, it is necessary that the relative permeability and capillary pressure characteristics and displacing fluid viscosities be identical for the systems compared. A method is presented by which accurate prediction of the performance of a gravity drainage system can be made. Close agreement between experimental and calculated drainage performance shows that steady state relative permeability and static capillary pressure data can be used to describe fluid displacement behavior. The very wide range of liquid recoveries before gas breakthrough which result from production rate variation alone demonstrates the importance of this factor in planning depletion of a gravity drainage reservoir. Calculated results are presented which show that little additional recovery can be expected from a high pressure gravity drainage system between the times of gas breakthrough and attainment of such high gas/liquid ratios as to make further pressure maintenance impractical. INTRODUCTION It bas been recognized for some time that gravity forces play an important part in the recovery of oil from some types of reservoirs. Field experience has shown that under certain conditions, gravity drainage can result in very high oil recov- eries. Qualitative reasoning has led most engineers to the general conclusions that: (1) Where gravity drainage is important, the reservoir pressure should be maintained by gas injection at the crest of the structure to prevent shrinkage of the oil in place and to keep a low viscosity so the oil can drain at the fastest possible rate. (2) Recovery by gravity drainage is rate sensitive. A survey of the literature indicates that while considerable work has been done on the effects of gravity in oil production problems, no satisfactory method of calculating the performance of gravity drainage reservoirs has been reported.1,2,3,4,5 In the absence of any proven method of calculating reservoir performance, the level at which pressure should be maintained and the rate of production for most efficient operation has been open to debate. The limits and general character of the recovery us rate relationships are apparent from the following: As rates of production approach zero, oil will drain by virtue of its own weight fast enough that the saturation distribution is always approximately the same as the original static capillary distribution. That is, at the gas-oil contact the liquid saturation goes from 100 per cent to a value of perhaps 10 to 30 per cent in a very short distance, so that as production continues. a relatively sharp gas-oil contact moves down-structure, leaving a very low residual oil saturation in the originally oil saturated zone. At very high rates of production, the oil that drains by virtue of its own weight is negligible and recovery will approach that of a horizontal gas drive, leaving a much higher residual oil saturation. At intermediate rates of production. recovery should be between these extreme*. Despite the lack of quantitative methods, tentative agreement had been reached on the question of optimum producing rate. It has been generally concluded that rather sharp decrease in recovery would occur at rates of production above the "maximum rate of gravity drainage" and hence this rate should not be exceeded. The "maximum rate of gravity drainage" is defined as the rate of production from a 100 per cent

Jan 1, 1951

THIS chapter and Chapter 19 deal with the heat quantities involved in open-hearth steelmaking, including the thermal efficiency of the furnace as a generator of high-temperature heat, the heat storage in the steel and slag produced and in the furnace walls, and the heats of the various chemical reactions involved in combustion, in the formation of slag, and the refining of steel. The fundamental laws to be considered are the first two laws of thermodynamics as applied to problems involving sensible and potential (or latent) heat only: 1. Heat input equals heat outflow plus storage. 2. Heat may be transferred only from a hotter body to a colder one. The first of these laws relates to the various heat quantities or the heat balance of the process. No one has as yet made an open-hearth heat balance that came out almost exactly balanced. The cause probably lies in the difficulties of accurate temperature and flow-rate measurements at the high temperatures involved and the inherent complexities in flow distribution and air leakage present in any real open-hearth furnace system. Some idea of the magnitude of the heat quantities involved can be obtained by a brief, crude outline of the heat balance of a 90-ton heat of steel. We will assume a 60 to 70 per cent hot- metal charge in a fairly fast working and only moderately efficient furnace, burning fuel oil, with a fuel consumption of around 4 million Btu per net ton of ingots produced. The time from start of charge to tap is 9 hr. During this period, the oil burned represents 360 million Btu and the sensible heat in the preheated air at the port ends is 117 million Btu, so that the total heat input at the ports is 477 million Btu. Heat stored in the steel and slag at the end of the heat, plus the various amounts absorbed by certain bath reactions, amounts to a total of 195 million Btu, but 120 million of this is supplied by the heat in the hot metal and by various heat-evolving reactions in the bath,

Jan 1, 1951

By H. K. Birnbaum, H. B. Aaron

he authors suggest that a number of the types of yield phenomena which have been observed in high-purity fcc metals are due to dislocation interactions bccurring at the surface of the crystals rather than due to volume effects. Since rather different inter-pretationS2,7,12,14,15,21-23 of these effects have been suggested, it is of some importance to ascertain the role of the surface in these yield phenomena. It should be first noted that the high-purity fcc metals appear to exhibit several distinct types of yield phenomena. The "unloading yield point" which is observed on reloading the specimen after removing the applied load has been found to be independent of the time of holding in the unloaded condition. If however the specimen is aged while under load and re-tested without removing the load, a yield point is observed which does depend on the aging time and tem-perature. Feng and Kramer suggest that the removal of the unloading yield point on removing sufficient material from the surface of the specimen indicates that the effect is associated with dislocation interactions at the specimen surface. Their observations are counter to those of Haasen and Kelly5 and Birnbaum.12 Since the unloading yield points are extremely small (-2 pct of the flow stress) the results of the surface removal will depend on whether the material is removed uniformly over the gage length. The introduction of small etch pits or the removal of more material from one portion of the specimen than from another will result in preferential yielding and obliteration of the yield point. With the normal electropolishing techniques it would be difficult to avoid these effects. The data obtained by Aaron and Birnbaum, Fig. 10, on aluminum polycrystalline specimens indicate that, although the unloading yield point and the strain-aging yield point are not simply additive, a time- and temperature-dependent yield point is observed under conditions where no creep is observed. This does not agree with the results of Feng and Kramer but does agree with the results on copper15 and gold.7~23 The source of the discrepancy may be the procedure used by Feng and Kramer to correct their time-dependent yield points for the effect of creep. Since the strain-aging yield point is not independent of the pre-aging strain rate, Fig. 11, the effects of creep cannot

Jan 1, 1967

By F. Peter

I. GENERAL INTRODUCTION. TECHNICAL progress takes place in two directions: the improvement of methods, affecting the quality of the product; and increase in the economy of operations, affecting its cost. In the iron-industry, practice is pretty well settled, and. revolutionary changes of method are, for the present, not to be expected. Hence, in this industry, the principal endeavor is to reduce costs by the use of labor-saving inventions, such as the machines brought into use during the last decade. But it is not alone necessary to reduce the labor-cost; complete economy requires also a saving in raw material. Under this head we may rank the coal employed as metallurgical fuel; and it follows that progress includes the economic use of fuel, so managed as not to injure quality of product. In the present paper it will be shown how, by suitable utilization of the heat from the furnace, a large portion of it may be made available for other purposes. Such utilization of waste-gases is important in all industries which employ furnaces (especially heating- and smelting-furnaces); and in the first rank of these stand the iron-, glass-, and porcelain-manufactures. The following pages are devoted chiefly to the waste-gases of smelting-works, and especially to those reverberatory-furnace gases which are not combustible.&apos;

Jan 12, 1913

By L. W. Legerwood

During the past three decades, the oil industry has expended increasing eflorts seeking improved drilling tools or systems to reduce drilling costs. The total cost of these efforts is unknown, but it certainly amounts 10 tens of millions of dollars. Most of the "new" system that past and present investigators have sought to develop actually are old public information. In seeking to implement new-systern concepts, investigators have tested the following: impact at frequencies ranging from 6 to 300 cycles per second; electrical, mechanical and hydraulic meam of actuating percussors; bit rotary speeds up to 2,000 rpm; electric and hydraulic bottom-hole means of rotating bits; bottom-hole machines with power outputs up to 400 hp; shock waves; explosives; high-velocity pellets; flame; arc; grinding wheels; abrasive jets; erosion by high-velocity gases; chemical attack; electric current; magnetic waves; retractable rock bits; reelable drill pipe; continuous coring with reverse circulation; and automation of drilling rigs. Table I shows how these investigations are grouped for discussion purposes in this paper. In spite of these efforts to discover new and improved systems, rotary drilling main;aim its economic leadership. Undoubtedly, rotary drilling costs will continue to be reduced by rigid application of the best available technology and by development of new rotary technology. In view of the extensive past development programs, however, significant long-range improvement appears to be a research, not a development problem. Research must postulate and prove theories and principles governing variour subsurface rock-failure processes pertinent to both rotary and new systems. Ah, research must produce physical and engineering data relative to these processes. When such information is available, earth boring will graduate from an art to a science. Major improvements in rotary drilling can then be expected, and the systematic evolution of an improved drilling method can be initiated—with a strong probability for success. Development of drilling methods other than rotary drilling has been one approach investigated by the industry as a means for reducing drilling costs. Major cost-reduction efforts, however, have been centered on engineering development work aimed at incremental improvements in rotary drilling. A relatively minor effort has been expended to establish basic physical principles and engineering data pertaining to the earth-boring process which can serve as a foundation for the development of cost-cutting drilling hardware. Current oil-industry economic trends have added impetus to the need for effective programs to reduce drilling costs. However, areas for expanded future efforts should be selected only after careful study of past investigations. It is the purpose of this paper to review past and Dresent industry efforts to develop new drilling tools or systems and to suggest areas where additional science is needed. Past reviews of drilling methods have been limited to a few processes prominent at the time the reviews were made. This paper seeks to present a concise, well organized review of all methods that have received actual development or test work. The preparation of a paper seeking to review all past developments is fraught with many difficulties, not the least of which are errors in or obsolesence of printed matter used as source material and the lack of data on industry developments which have not been published. Since de-

By John Cogan

Field observations were made of rock phenomena in shale, dolomite, and fractured quartzite in the Burgin Mine, Eureka, Utah. Draft closure rates were measured with extensometers and convergence gages. In addition the effects of hydraulic props upon the retardation of closure was also monitored. Drift closure rates were found to be constant and to vary between 0.32 x 10-8 min-1 for dolomite and 23.8 x 10-8 min-1 for soft shale. The installation of props set at constant load served to retard the closure rates. General results show closure to occur at a constant rate for all cases, to be non-uniform around the drift openings, and to be increasingly retarded toward a zero rate by increases in prop load.

Jan 1, 1979

By George Macready

TRINIDAD, British West Indies, is an island near the north coast of South America, situated between latitudes 10° and 11° N:, and. opposite the numerous outlets of the Orinoco River Delta. It is separated from Venezuela by the Gulf of Paria (salt, water) and straits over 5 mi. (8 km.) wide. The area of the island is approximately 1750 sq. mi. (453,- . 250 hectares) and the population is approximately 400,000. The climate is tropical with an annual rainfall of from 45 to 60 in. (114 to 152 cm.). The oil fields consist of several units, or fields, located in the southern half of the island. Approximately 90 per cent. of the total production has been yielded by fields situated within 7 mi: (11.3 km.) of the famous asphalt lake and on the southwest peninsula. The most important producing fields, or units, are the following, which are shown on the accompanying map: Brighton, or Pitch Lake Field, operated by the Trinidad Lake Petroleum Co., Ltd., is situated beside the famous Pitch Lake; it, even encroaches on the lake. Vessigny Field, operated by the Trinidad Lake Petroleum Co., Ltd., is situated 2 mi. (3.2 km.) south of Pitch Lake. Lot One Field, operated by the Petroleum Development Co., Ltd., the United British Oilfields of Trinidad, Ltd., and Stollmeyer, Ltd., is situated 3 mi. south of Pitch Lake upon Lot One of Morne 1&apos;Enfer Forest Reserve and adjoining properties. Parry Lands Field, operated by the United British Oilfields of Trinidad, Ltd., and the Petroleum Development Co., Ltd., is situated 3;2 mi. south of Pitch Lake on Lot Three of Morne l&apos;Enfer Forest Reserve and adjoining properties. Point Fortin Field, operated by the United British Oilfields of Trinidad, Ltd., is situated at Point Fortin, 6 mi. southwest of Pitch Lake. Fyzabad Field, operated by Trinidad Leaseholds, Ltd., is situated several miles southwest of Fyzabad Village and 6 mi. south-southeast of Pitch Lake. Barracpore Field, operated by Trinidad Leaseholds, Ltd., is situated several miles south of. San Fernando and 15 mi. (24.14 km.) east of Pitch Lake.

Jan 9, 1920

By John Birkinbine

Through the partiality of my fellow-members I have been able, during seven years&apos; service on the Council of the American Institute of Mining Engineers, to note the development of technical societies, a subject which commends itself as an appropriate theme for me, in retiring from the office of President, at a time when we meet in convention with Canadian technical societies. Our next assembly, called at Chicago at the time fixed for an International Engineering Congress, offers additional reason for the selection of this topic. If subsequent statements appear to give to the American Institute of Mining Engineers greater prominence than to kindred organizations, they may be excused upon the ground of long association with and loyalty to its members, and to a personal knowledge of their work. Besides, data as to its growth and development are more accessible; and at a meeting of the Institute features connected with it may be considered as of greater immediate interest than those affecting other organizations. The purpose of this address is, however, to use the record of the Institute as indicating a similar development of other technical societies, rather than to claim preeminence for any organization; the work of each must speak for it. There is a general tendency to form associations at the present time. Organizations have been created and are active in every profession and in all branches of labor, trade, industry, commerce, manufactures, science and art. A record of such associations and their aggregate membership would be startling, and would show how large a percentage of the population of North America is connected with one or more of them; but the figures cannot be even approximately estimated. The class of associations representing national, state, or local trade interests, such as boards of trade, chambers of commerce, etc., may be used as an illustration. A late report shows that in the

Jan 1, 1893

By C. W. MacGregor

THE observation of the flow layers, or Lüders&apos; lines, produced in mild steel when it is stressed into the plastic range often provides considerable useful information for the study of the fundamental mechanism of the plastic flow of metals. It is a commonly observed fact that as soon as the upper yield point in a mild-steel tensile-test bar is passed, an unstable condition develops in the equilibrium, the load on the testing machine drops and if the surface of the bar contains a thin mill scale, the latter begins to flake off rapidly along certain "lines." These "lines" are in reality traces of wedge-shaped flow layers and are formed by the intersection of the surface of slip and the surface of the bar. The average plane of the flow layer itself has been found by various experimenters to be inclined at an angle of approximately 45° to the axis of the test bar. In a body of more complicated shape stressed in possibly a different man-ner, the tangent planes to the flow layers at each point seem in many cases to be inclined at an angle of about 45° to the principal stress direc-tions at the point. As examples of the latter may be mentioned the logarithmic spirals obtained when a rivet hole is punched in a thin plate, or when a tube is subjected to internal pressure only, etc. Hence if the flow layers are observed from an experiment, the shear-stress trajectories -the curves indicating the directions of the maximum shearing stresses in the body-may then be approximately determined. Since the latter curves form an orthogonal family inclined at 45° to the principal stress directions, the family of principal stress trajectories, or the curves indicating the directions of the principal stresses, may be thus obtained. Although the discontinuous type of stress-strain curve at the yield point is commonly observed with test bars of mild steel, more recent experiments have shown that this is by no means the only material exhibiting this interesting phenomenon. A similar effect has been observed in zinc and cadmium crystals, by Becker and Orowan;1 in duralumin and other aluminum alloys, by Dawidenkow,2 Elam,3 Fell, and others; in copper and copper-alloy crystals, by Elam;5 in brass by Elam;5 in brass wires by deForest;6 in higher carbon steels, tungsten steel, and

Jan 1, 1939

By E. DeGolyer

I. INTRODUCTION VOLCANIC origin. was among the first of the theories advanced to account for the occurrence of the salt domes of the Gulf coastal plain, northern Louisiana., and eastern Texas, and it is still being re-stated in various forms by the most recent contributors to our knowledge of the geology of such deposits. Argument has been largely by analogy and attention has repeatedly been called to the Mexican oil fields, particularly those of the Tampico-Tuxpam region, because of the occurrence of oil in close proximity to volcanic plugs in those fields, an occurrence supposed to have some resemblance to the common occurrence of oil in the salt domes of the United States. The author, having spent several months of the past year in a general study of salt domes and in a detailed study of certain domes in the United States, and having been acquainted for some time with the exploration of similar domes in the Isthmus of Tehuantepec region, Mexico, and with the general geology of the Tampico-Tuxpam region, Mexico, has reviewed the various theories of volcanic origin for salt domes which have been advanced to the present time. The purpose of this paper is to present such review and to discuss the supposed Mexican analogy.

Jan 5, 1918

This report presents the comments of members of the Institute&apos;s Sub-committee on Physics of Mine Ventilation on the proposals of a special committee of the Institute of Mining Engineers (London). This report is as follows: THEORY OF MINE VENTILATION Abstract of a report submitted June 16, 1925, to the Council of The Institution of Mining Engineers by a Special Committee Laws of Flow of Aib The law of flow of air in mine galleries is, at present, expressed by two formulas differing slightly in shape but both derived from the original hydraulic formulas of Chezy and others. These formulas are: The Atlcinson Formula.—Pa = KsV2, which in transformation becomes a3 where P = pressure producing flow; K = coefficient of friction; s = surface of the mine galleries; V = velocity of flow; Q = rate of flow; a = area of mine galleries. This formula is especially applicable to mine galleries, but is unwieldy in application, as in many problems we are dealing with changes produced in the same set of airways when K, s, and a are assumed not to change, and the only variables are P and Q. Great uncertainty prevails as to the exact values to be assigned to the coefficient K in different types of airway, as different workers have given widely differing values. This formula assumes: (I) That resistance to flow is independent of the pressure within the gallery. (2) That changes in volume within the limits of pressure ordinarily met with may be neglected. (3) That changes in density and viscosity and mode of flow of the air may be neglected. (4) That the coefficient K is a constant. (5) That P is proportional to the square of the velocity. We cannot find any reliable experimental work leading us to conclude how far these assumptions are justifiable in mining practice. Equivalent Orifice Formula.—The fundamental form of this formula is Q = ~nA.\/2~11

Jan 1, 1927

By W. H. Emmons

MANY mineral veins occupy faults, and movements on certain warped fault planes have resulted in openings. On normal faults the [ ] steeper parts have the widest openings, and on reverse faults the flatter parts have the widest openings. Theoretically the width of the opening is the sine of the angle of deflection times the amount of movement on the fault plane, but actually the widths of some of the openings are probably less because of readjustments of walls along joints or of other readjustments. The first treatment of the subject seems to have been in a book on mineral veins by John Leithart, published in Newcastle, England, in 1838. Later the subject was treated in various texts published in Germany, in England, and elsewhere. The subject was not given much prominence in the earlier American literature on economic geology, but has interested several workers in that field in the past decade. In this paper examples of districts showing ore shoots on warped faults, with relations noted, are described. Fault veins of the three depth classes of veins are noted. Many epithermal veins are in normal faults, and commonly the larger ore shoots are in their steeper portions. Many mesothermal veins are in reverse faults and many others are in normal faults. The flatter parts of veins in reverse faults are commonly wider than the steeper parts, although they are not always as rich as the steeper segments of the veins. There are not many hypothermal veins in faults of measured displacement.

Jan 1, 1943

By V. Apraxine, J. Lakaye, J. J. Saquet, P. Troch

Union Minière du Haut-Katanga owns concessions for extracting copper and associated metals in the high plateau region of Katanga. The concession is about 188 miles long by 44 miles wide and has three principal areas: Southern area-The Prince Leopold mine is an underground operation from which a copper-zinc sulfide ore is extracted. The mine and associated concentrator are at Kipushi. Copper concentrates are smelted and converted to blister copper at the Lubumbashi smelter at Elizabethville.

Jan 12, 1962

By W. N. Lacey, B. H. Sage

THE results of an extensive experimental program relating to the effectiveness of gravel screens have been correlated. The factors considered in some detail include gravel size and condition of packing, sand size and size distribution, fluid velocity, fluid viscosity, and thickness and arrangement of gravel screens. Good agreement between calculated values based upon probability considerations and experimental results relating to the influence of the thickness of the gravel screen was obtained. All of these factors are treated in the correlation in order that their influence may be taken into account in ascertaining the characteristics of an effective gravel screen for a particular set of conditions. The details of the experimental program are not given in the present paper but a description of generalized behavior and typical experimental results are recorded in graphic form. INTRODUCTION Gravel screens have been placed in water and oil wells for a number of years1,2,3 with the dual objective of increasing the productivity and decreasing the entrance of sand into the well bore. An understanding of the factors controlling the effectiveness of gravel screens in this connection is of industrial interest because it will lead to the proper selection of gravel. Some of the fundamental considerations involved in the migration of sand through a coarser body of porous materials were investigated by Coberly and Wagner4 and further experimental work has been carried out by Gumpertz.5 Apparently the pertinent phenomena are somewhat complex and are influenced by many variables. The present paper deals with the prediction of the behavior of gravel screens under the conditions encountered in practice but does not attempt to discuss the experimental methods or results that were obtained as a background and upon which the prediction is based. INFLUENCE OF GRAVEL SCREENS UPON PRODUCTIVITY The use of a gravel screen may increase the productivity of a well by increasing its effective diameter, and this constitutes one of the objectives of its use. The permeability of most gravels and coarse sands that are employed in practice is so large compared to that of the sand in place that relatively little loss in production rate will arise from the use of material fine enough to cause the desired resistance to sand migration. For example, in Fig. I is depicted the approximate variation in the permeability of closely sized spherical gravels under the conditions of packing likely to be encountered in screens. The dotted lines indicate the variation that might be found because of differences in packing. It should be realized that the permeability is not a single-valued function of the. average grain diameter but is related to a large number of factors, including the size, the size distribution and the shapes of the particles. However, Fig. I does permit a rough estimation of the permeability of closely sized- spherical gravels and shows that the permeability with even the smaller particles is very large compared to that of most petroleum production horizons.

Jan 1, 1941

By L. L. Melton, W. T. Malone

Fluid mechanics research conducted with non-Newtonian fluid systems now permits prediction of the behavior of these fluid systems in both laminar and turbulent modes of flow through circular pipes. Present work concerns non-Newtonian fluid systems currently used in the hydraulic fracturing process. During fracturing treatments, an unsteady-state condition may frequently be encountered arising from. the reaction rate of a chemical additive. This condition must be evaluated in order to predict the actual behavior of a particular fluid during field application. Design and operation of the apparatus used to determine fluid-flow behavior permit obtaining data under such non-equilibrium conditions. This paper shows methods used to obtain rheology measurements, develop hydraulic relationships and evaluate chemical reactions producing unsteady-state conditions. Engineering application of this research is illustrated by employing measured rheological values and developed hydraulic retationships to produce frictional pressure loss (psi/100 ft) us flow rate (bbl/min) charts of common tubing and casing sizes for an example fracturing fluid. How these charts and chemical reaction rate information are then combined to predict actual turbulent hydraulic behavior during unsteady-state field conditions is also discussed INTRODUCTION Many fluids used in hydraulic fracturing contain chemical additives which impart non-Newtonian fluid properties that may drastically alter their hydraulic behavior. Equally drastic alteration in wellhead pressure, injection rate and hydraulic horsepower requirement may result from these fluid properties. Prior research conducted to relate non-Newtonian fluid properties with hydraulic behavior has not as yet produced a universal relationship, particularly for the turbulent flow region. which of the many Possible non-Newtonian fluid properties is responsible has not been conclusively established. A systematic description, suggested by Metzner, of the many possible non-Newtonian fluid properties exhibited by real-fluid behavior, and a current discussion of theoretical and applied aspects of non-Newtonian fluid technoloy can be found in Handbook of Fluid Dynamics. f Little or no research has previously been attempted with fluids exhibiting time - dependent properties. Addition of chemicals during a fracturing treatment is often accomplished by continuously mixing and displacing the fluid. This produces a time-dependent effect or unsteady-state condition while the fluid is progressing through surface and wellbore conductors. This condition is due to solution or chemical reaction of the additive. Considerable departure from conventional methods of obtaining and interpreting data was found necessary to consider these conditions. Therefore methods were developed to obtain hydraulic behavior information under these complex, unsteady-state conditions. Relationships presented in this paper to predict hydraulic behavior of non-Newtonian fluids in circular pipes were obtained by constructing and operating a small pipeline apparatus in the manner of a pilot-plant study. These relationships are suggested as scaleup equations and are not proposed as fundamental rheological parameters. While perhaps deficient from a fundamental research viewpoint, a pilot-plant study does permit the determination and convenient evaluation of variables pertinent to a process. A pilot-plant study can result in a valid engineering application procedure even when fundamental relationships are still undefined. An excellent series of articles by Bowen has appeared in the chemical engineering literature.2-8 These give a thorough review of proposed hydraulic relationships and their limitations for non-Newtonian fluid behavior in circular pipes. A graphical method is presented to scale up data for a fluid exhibiting an anomalous hydrau1ic behavior in the turbulent flow region. Considerable assistance has been obtained from these articles to interpret the anomalous behavior noted during this investigation. These articles also provided assurance that a pilot plant is a practical approach to evaluate the hydraulic behavior of non-Newtonian fracturing fluids. _____________

Jan 1, 1965