Search Documents

ALABAMA Anniston.-Bretz, J A Carnngton, F G Gerber, A B Ashland -Barton J Sturdevant, J C Bessemer -Abbott, C E Ball, T L Ferguson, V Salmon, H S Schaber, C F Thompson, N E Whatley, W J Birmingham.-Adams, J H -Aldrich, T H Aldrich, T H , Jr ALASKA Anchorage -Dyer, B W. Parker, H C Smith, S S Chichagof.-Baumann, H N , Jr Copper River.-Douglass, W C Cordova.-Hazelet, G C Fairbanks -Davis, J A Hyder -Pitt, D L Juneau -Jackson, G. T Murphy, R E R..11 ti At i

Jan 1, 1923

By Henry Fay

THE erosion of guns is a complex problem which can be solved only by a detailed study of all the factors involved. In the present paper it is proposed to submit the results of observations and experiments which have extended over several years. Certain facts have been established and preliminary reports have been published.' Conclusions have been reached since then which, it is believed, are worth presenting for the purpose of promoting discussion, and with the hope that ultimately the whole truth will be known. The particular phase of the problem which will be presented here is the hardening of the inner surface of the gun tube. It has been known for a long time that after firing a large caliber gun for some time, the surface of the metal becomes hard and brittle, cracks, and wears away.2 The character of this phenomenon may be learned by an examination of some results which are typical, obtained from a detailed study of a 12-in. gun. The gun was trepanned and rings representing various sections of the gun were cut out for examination. The first ring represented the metal at the muzzle end, and the other rings were removed at approximately 120, 240, 325 and 337 in., respectively, toward the breech end. The appearance of the surface of the metal in the different sections is shown in Fig. 1. The greatest amount of wear and maximum amount of hard surface layer was found in section marked E, which is nearest the powder chamber and at the beginning of the rifling; the maximum amount of cracking in D; the maximum amount of copper deposition in C. Section B showed heat cracks on both lands and grooves, and section A showed heat cracks on the driving edge of the lands only. There was much flow of metal in both sections E and D, and there was progressively less effect noticeable toward the muzzle end. The polished cross-section of these same pieces is shown in Fig. 2. The

Jan 12, 1916

By R. W. Moore, A. B. Kinzel

Although the iron-carbon diagram has undergone many changes in the last 20 years, the region below the eutectoid line and up to approximately 1.7 per cent carbon has been little affected. This region is generally considered to consist of cenlentite and ferrite. Graphite has been noted occasionally in the hypereutectoid steel region, and the ready formation of graphite nodules in malleable cast iron is a phenomenon difficult to interpret in the light of cementite, supposedly stable at sub-eutectoid temperatures. In this case the graphite formation has been partly explained by the presence of silicon, and many have believed that silicon acts to change the stable state rather than to accelerate reactions so as to arrive at the stable state in a briefer period of time. Consideration of this phenomenon indicates that cementite is not the stable phase in the temperature composition zone referred to. In the course of examining a low-carbon steel tube taken from a petroleum cracking still, which had been in service for approximately three years at temperatures somewhat below the eutectoid temperature, observations were made that shed light on this entire subject. The tube in question analyzed:' C, 0.15 per cent; Mn, 0.49; Si, 0.02; S, 0.023; P, 0.015. The microstructure of the tube after service is shown In Figs. 1 and 2. From these it is evident that cementite as such is absent, and that in its place nodular graphite has been formed. In order to check this observation further, samples taken from the tube were heated at 850" C. for varying periods of time. The small samples were put into a large hot furnace, and the total time is recorded. The structure of the sample after 5 min. at 850" C. is shown in Figs. 3 and 4, and the nest of pearlite surrounding the graphite nodules is most satisfactory evidence of the character of the nodules. As the length of time of heating at this temperature increases, the pearlitic zone increases, with final restoration

Jan 1, 1935

By R. W. Moore, A. B. Kinzel

Although the iron-carbon diagram has undergone many changes in the last 20 years, the region below the eutectoid line and up to approximately 1.7 per cent carbon has been little affected. This region is generally considered to consist of cenlentite and ferrite. Graphite has been noted occasionally in the hypereutectoid steel region, and the ready formation of graphite nodules in malleable cast iron is a phenomenon difficult to interpret in the light of cementite, supposedly stable at sub-eutectoid temperatures. In this case the graphite formation has been partly explained by the presence of silicon, and many have believed that silicon acts to change the stable state rather than to accelerate reactions so as to arrive at the stable state in a briefer period of time. Consideration of this phenomenon indicates that cementite is not the stable phase in the temperature composition zone referred to. In the course of examining a low-carbon steel tube taken from a petroleum cracking still, which had been in service for approximately three years at temperatures somewhat below the eutectoid temperature, observations were made that shed light on this entire subject. The tube in question analyzed:' C, 0.15 per cent; Mn, 0.49; Si, 0.02; S, 0.023; P, 0.015. The microstructure of the tube after service is shown In Figs. 1 and 2. From these it is evident that cementite as such is absent, and that in its place nodular graphite has been formed. In order to check this observation further, samples taken from the tube were heated at 850" C. for varying periods of time. The small samples were put into a large hot furnace, and the total time is recorded. The structure of the sample after 5 min. at 850" C. is shown in Figs. 3 and 4, and the nest of pearlite surrounding the graphite nodules is most satisfactory evidence of the character of the nodules. As the length of time of heating at this temperature increases, the pearlitic zone increases, with final restoration

Jan 1, 1935

By G. F. Comstock

THE subject of transverse fissures in steel rails has been discussed very thoroughly in recent years from various points of view and the final opinions expressed may be roughly classified into two groups: (1) That these fissures are the result merely of fatigue of the steel and are independent of the quality of the metal. (2) That the quality of the metal and the mill practice must have something to do with them. The first point of view was most-ably and logically presented by J. E. Howard,1 and in the discussion of this paper, as well as in several other preceding publications, Dr. P. H. Dudley, Consulting Engineer of the New York Central Lines, has strongly defended the other opinion.2 The steel makers of the country have naturally rallied under Mr. Howard's banner, hoping to place the entire blame for these. failures upon the railroads with their high wheel-loads, hard steel, heavy traffic, and sometimes inferior roach-bed; while the railroad men,, on the other hand, have been busy accumulating statistics and records in the effort to find an actual reason in the rails themselves that would account for the seemingly haphazard occurrence of transverse fissures under varying conditions and at widely separated points. The view that these fissures were due merely to normal fatigue under alternating stresses seemed most reasonable to the writer until quite recently, because from work clone in this laboratory, as well as the work of other investigators of the problem, no structural differences, in the vast majority of cases, were found between metal at the nuclei of transverse fissures and metal at similar positions in the same rails or in other rails that had not developed fissures. . Within the last year or two, however, since the method of etching polished sections for the microscope with a cupric chloride solution has been tried systematically. on lengthwise sections, passing through the nuclei of transverse fissures, evidence

Jan 11, 1918

By H. J. Hand

Statistical methods are becoming increasingly important for interpreting routine reports, or for analyzing special test data in industrial plants, such as steel plants. They have already become practically a necessity to the plant metallurgist. A paper by Chancellor, 1 written in 1933, gives many examples of the benefits the plant metallurgist can derive from the use of these methods. The present paper discusses applications of importance to many others who must analyze reports in the steel plant, as well as other examples of interest to metallurgists. Statistical Methods Logically Suited to Plant Problems.—Statistical methods are not new as a branch of mathematics. Until comparatively recently, however, practical applications were confined mainly to actuarial science, biology, and economics; fields in which an observed result is obviously influenced (and often determined) by a complicated set of variables more or less constantly tending to affect it. As pointed out by Daeves,2 a decade or more ago, problems in industry are basically similar to those in these other fields in that a given result is at least partly due to that chance combination of causes happening to be present at the time. When trying to do the same thing repeatedly, constant results are never attained; they vary about the desired result with more or less well defined mathematical regularity. Such a condition arises out of the great number of factors tending to affect the final result. If statistical methods are so valuable to the biologist or economist, why then should they not also be of great value to plant managers and engineers, and to all who must interpret reports from various sources in the industrial plant? Within the last few years, industry has become conscious of this situation, and the use of these methods has been rapidly expanding in such p1ants. Many Useful Statistical Devices Available.—Many statistical methods of attack are available for the analysis of plant data. It is the object of

Jan 1, 1938

By H. J. Hand

Statistical methods are becoming increasingly important for interpreting routine reports, or for analyzing special test data in industrial plants, such as steel plants. They have already become practically a necessity to the plant metallurgist. A paper by Chancellor, 1 written in 1933, gives many examples of the benefits the plant metallurgist can derive from the use of these methods. The present paper discusses applications of importance to many others who must analyze reports in the steel plant, as well as other examples of interest to metallurgists. Statistical Methods Logically Suited to Plant Problems.—Statistical methods are not new as a branch of mathematics. Until comparatively recently, however, practical applications were confined mainly to actuarial science, biology, and economics; fields in which an observed result is obviously influenced (and often determined) by a complicated set of variables more or less constantly tending to affect it. As pointed out by Daeves,2 a decade or more ago, problems in industry are basically similar to those in these other fields in that a given result is at least partly due to that chance combination of causes happening to be present at the time. When trying to do the same thing repeatedly, constant results are never attained; they vary about the desired result with more or less well defined mathematical regularity. Such a condition arises out of the great number of factors tending to affect the final result. If statistical methods are so valuable to the biologist or economist, why then should they not also be of great value to plant managers and engineers, and to all who must interpret reports from various sources in the industrial plant? Within the last few years, industry has become conscious of this situation, and the use of these methods has been rapidly expanding in such p1ants. Many Useful Statistical Devices Available.—Many statistical methods of attack are available for the analysis of plant data. It is the object of

Jan 1, 1938

By Allen L. Hatch

A survey of all phases of the world's lead and zinc production in 1968 from ore through to refined metal was conducted by sending questionnaires to individual companies and the results of this survey are tabulated at the end of the paper. The paper goes on to review changes in the geographical distribution of the world's lead and zinc mine and metal production and in the trading patterns of raw materials, present and future utilization of metal production capacity, developments in metal smelting and refining processes and the growing importance of marketing, product development and research in the 1950's and 1960's.

Jan 1, 1970

By P. A. Vukmanic, M. Gensamer

Only recently has it been realized that preferred orientations are common in hot-rolled steels. In a recent paper, N. P. Gossl stated that hot-rolled mild steel exhibits a texture different from that characteristic of cold-rolled steel. No complete study of these hot-rolling textures has been reported using the pole-figure method of Wever. The material used in the work reported in this paper was the same material used by Gensamer and Mehl2 in a recent study of preferred orientations in cold-rolled steel, to which reference may be made for the composition and thermal history of the steel. Automobile-body sheet bar 1/4 in. thick was hot-rolled at two temperatures, 780' and 910' C. (1436' and 1669' F.). These temperatures refer to the temperature of the furnace in which the steel was heated; after each pass the steel was returned to the furnace and held there long enough to return to temperature. Although no accurate method was used to measure the temperature after each pass, it was estimated by color that only a slight drop in temperature occurred. In order to determine the effect of any preferred orientation that might have persisted through the normalizing treatment, one specimen at each temperature was rolled in the same direction as the original working direction and the other at right angles to it. The total reduction in each case was 85 per cent, the specimens having been reduced from 0.250 to 0.0375 in. in five passes. Final cooling was in air. Pinhole reflection photograms were taken of all four specimens, with the rolling direction vertical and the X-ray beam at an angle of 7' with the transverse direction (the transverse direction is defined as that direction in the rolling plane perpendicular to the rolling direction). These photograms, taken with a Mo target at 35 kv., are reproduced in Figs. 1, 2, 3 and 4. They show that a more pronounced texture was developed by the low-temperature rolling (780' C.), and that of the two

Jan 1, 1937

By R. W. Raymond

(Pittsburg Meeting, March,1910.) THE Giroux Consolidated Mines Co. is equipping a five-compartment shaft at Kimberly, Nev., which will serve the Alpha mice. The depth of this shaft, January, 1910, is 963 ft., and of this depth 948 ft. was opened by raising, 15 ft. of sinking was done so that the bearers, collar-set, and three shaft-sets might be installed and concreted, and with this done it was possible to erect the necessary surface-equipment for resuming shaft-timbering on the completion of the raise. The arrangement of the shaft-timbering is shown in Fig. 1. At the 1,000-ft. level of the Alpha, and 750 ft. SW. from the Alpha shaft, a 14- by 18-ft. station was cut, and a 25-h-p. air-hoist *as installed. From here the raising commenced on July 5, 1909. The raise was cut approximately 13 by 21. ft. in area, and supported by timbering with square sets, illustrated in Fig. 2, which shows the division into four compartments. The end compartments, which were used as chutes, had the center girts heavier than in the others on account of the wear from falling rock. The chute-lining was braced by inserting 8- by 8-in. stiffeners parallel to and half way between successive caps. Similarly, the lagging on the wall sides of the cage-way and the compartment for pipes and ladder was stiffened with 4- by 6-in. timbers. In the pipe-and-ladder compartment the chute-stiffeners were reinforced with 8- by 8-in, struts, and as the cage-way was partitioned off by braced lining, there was practically no chance of rock entering the ladder-way in case a chute burst into the cage-way. Over the two center compartments the last two, sets were always bulkheaded with 8- by 12-in. timbers, shown in Fig. 3, and from the lower bulkhead the cage sheave-wheel was suspended. After a round of holes had been blasted and the loose

Jun 1, 1910

By Ralph Smith

DEVELOPMENT of the lime industry in Ste, Genevieve County began in a crude way in 1840. According to information furnished by the Missouri Bureau of Geology, in the early days small vertical kilns built of stone were used, and wood was the fuel. Modern development began in 1904 when one company introduced steel shells lined with firebrick. Within a few years two more companies erected similar plants, and in 1925 a fourth company began operations. Thus there are today four lime companies at Ste. Genevieve, all operating at high capacity and with a gradually increasing production. GEOLOGY The limestone of Ste. Genevieve County, which has the chemical composition and purity required for lime burning, is the upper 80 or 90 ft. of Spergen formation. The Missouri Bureau of Geology, in its geological map of Ste. Genevieve County, gives the Spergen formation a total thickness of 160 ft., but only the upper portion is pure enough for lime burning, with an average raw-stone analysis of 98.7 per cent CaCO3; 0,35 Si02; 0,3 R203; 0.35 MgCO3; 0.3 SO3. The Spergen, one member of the Meramac group, Iowa series, of the Mississippian system, underlies an area approximately 12 miles long north and south, by 5 miles wide east and west (Fig. 1) in Ste. Genevieve County. The entire eastern two-thirds of Ste. Genevieve County is sedimentary, the formations dipping gently toward the east on an average grade of about 4 per cent, or 2 ½ °. Thus the outcrops of the various sedimentaries run approxi-mately north and south. A line running west from Ste. Genevieve crosses the outcrops of the sedimentaries, ranging from the top of the Mississippian to the Ozarkian geological system in a space of 12 miles. Thus with the gentle dip of 2 1/2° the 160-ft. thickness of the Spergen formation stretches out in its outcrop so that it is approximately one mile

Jan 1, 1938

By C. E. Shoenfelt, E. W. Krampert

The major oil discovery in 1938 for Wyoming was the General Petroleum Corporation's So. 1 Government, C.NW.SE. of sec. 21-35N-77W, on the Cole Creek structure in central Wyoming, 14 miles northeast of Casper. This well found commercial oil production in basal Cloverly sand (Lakota) at 7978 ft. and was completed on May 28, 1938, at 8019 ft., 3 ft. in Morrison shale. It had an initial produrtion of 10 bbl. of oil an hour but at the end of a 7-day test made 336 bbl. of oil in 24 hr. During 1938, the well produced a total of 23,161 bbl. of oil. It has been agitated about 10 days out of each month to provide fuel for lease and drilling operations, the balance of the time it has been shut in pending the completion of the second well on the structure. The Cole Creek oil is of intermediate base and has an A.P.I. gravity of 32.7". The record of the well contains the "tops" listed in the accompanying tabulation. Tops in General Petroleum Corporation's No. 1 Government Well Feet 2210 Top of the Mesa Verde (Teapot sandstone) 2960 Top Steele shale 4500 Shannon sand; good show of oil and gas 6740 Top Frontier sand; some oil saturation 6840 Halliburton test of Froutier did not show much oil, but at 6878 ft. the oil showing amounted to 50 barrels 6878-7051 Shale 7051-7062 Sand with some oil saturation 7062-7920 Shale (sandy phase of Thermopolis shale 7779 to 7788 ft.) 7920-7926 Sand (Muddy); oil-saturated 7926-7974 Shale 7974-7979 Hard, coarse, limy sand (Dakota); some oil saturation 7979-7997 Soft sand; high oil saturation 7997-8002 Shale with pyrites 8002-8016 Sand (Lakota) 8016-8019 Variegated Morrison shale 5600 Elevation Lance Creek Field.—Important extensions to the Lance Creek field in eastern Wyoming were made in 1938 by the completion of a number of

Jan 1, 1939

By C. E. Shoenfelt, E. W. Krampert

The major oil discovery in 1938 for Wyoming was the General Petroleum Corporation's So. 1 Government, C.NW.SE. of sec. 21-35N-77W, on the Cole Creek structure in central Wyoming, 14 miles northeast of Casper. This well found commercial oil production in basal Cloverly sand (Lakota) at 7978 ft. and was completed on May 28, 1938, at 8019 ft., 3 ft. in Morrison shale. It had an initial produrtion of 10 bbl. of oil an hour but at the end of a 7-day test made 336 bbl. of oil in 24 hr. During 1938, the well produced a total of 23,161 bbl. of oil. It has been agitated about 10 days out of each month to provide fuel for lease and drilling operations, the balance of the time it has been shut in pending the completion of the second well on the structure. The Cole Creek oil is of intermediate base and has an A.P.I. gravity of 32.7". The record of the well contains the "tops" listed in the accompanying tabulation. Tops in General Petroleum Corporation's No. 1 Government Well Feet 2210 Top of the Mesa Verde (Teapot sandstone) 2960 Top Steele shale 4500 Shannon sand; good show of oil and gas 6740 Top Frontier sand; some oil saturation 6840 Halliburton test of Froutier did not show much oil, but at 6878 ft. the oil showing amounted to 50 barrels 6878-7051 Shale 7051-7062 Sand with some oil saturation 7062-7920 Shale (sandy phase of Thermopolis shale 7779 to 7788 ft.) 7920-7926 Sand (Muddy); oil-saturated 7926-7974 Shale 7974-7979 Hard, coarse, limy sand (Dakota); some oil saturation 7979-7997 Soft sand; high oil saturation 7997-8002 Shale with pyrites 8002-8016 Sand (Lakota) 8016-8019 Variegated Morrison shale 5600 Elevation Lance Creek Field.—Important extensions to the Lance Creek field in eastern Wyoming were made in 1938 by the completion of a number of

Jan 1, 1939

By Arthur F. Taggart, Herbert H. Kellogg, Nathaniel Arbiter

The experimental work herein described is presented in support of the following broad hypothesis: Conditioning of metals and metallic sulphides by amine collectors involves metathetic reaction at the solid surface between the collector and an oxidized metallic compound, to produce a coating comprising an amine-bearing compound of low solubility in the system. The type of reaction is different in acid and in basic solutions; both types may occur simultaneously in near-neutral pulps. Experimental The experiments comprise contact-angle tests with a variety of metals and metallic sulphides and extraction teats on ground chalcocite. Contact-angle tests were made principally on metals. Covellite paralleled metallic copper in amine solution at pH 8.8 (Table 3) and in alkaline water, but maintained an angle of about 70° in Io-3 HCl solution, where metallic copper lost its angle. The tests with anionic collectors (Table I) indicate that the behavior of metals in general is parallel to that of their minerals in anionic solutions. It is believed that this is generally true with cationic collectors also, but the covellite test is a warning against a broad assumption to this effect. All test specimens were mounted in Transoptic.* All tests in conditioning solution were preceded by a test in distilled water; cleaning and polishing were continued in every case until the angle in water was zero. Subsequent transfers into and out of solutions and test cells were made in such a way as to prevent exposure of the surface to air.1 The amine used was primary laurylamine, Armour and Co., AM-1120. It was used in the form of the hydrochloride, obtained by precipitation with gaseous hydrochloric acid from an ether solution of the amine, and purified by two recrystallizations from ether-alcoho1.2 Inorganic and other test reagents were standard laboratory grades. Temperatures were not controlled; the probable range of test-solution temperatures is 650 to 80°F.

Jan 1, 1943

By Herbert H. Kellogg, Nathaniel Arbiter, Arthur F. Taggart

The experimental work herein described is presented in support of the following broad hypothesis: Conditioning of metals and metallic sulphides by amine collectors involves metathetic reaction at the solid surface between the collector and an oxidized metallic compound, to produce a coating comprising an amine-bearing compound of low solubility in the system. The type of reaction is different in acid and in basic solutions; both types may occur simultaneously in near-neutral pulps. Experimental The experiments comprise contact-angle tests with a variety of metals and metallic sulphides and extraction teats on ground chalcocite. Contact-angle tests were made principally on metals. Covellite paralleled metallic copper in amine solution at pH 8.8 (Table 3) and in alkaline water, but maintained an angle of about 70° in Io-3 HCl solution, where metallic copper lost its angle. The tests with anionic collectors (Table I) indicate that the behavior of metals in general is parallel to that of their minerals in anionic solutions. It is believed that this is generally true with cationic collectors also, but the covellite test is a warning against a broad assumption to this effect. All test specimens were mounted in Transoptic.* All tests in conditioning solution were preceded by a test in distilled water; cleaning and polishing were continued in every case until the angle in water was zero. Subsequent transfers into and out of solutions and test cells were made in such a way as to prevent exposure of the surface to air.1 The amine used was primary laurylamine, Armour and Co., AM-1120. It was used in the form of the hydrochloride, obtained by precipitation with gaseous hydrochloric acid from an ether solution of the amine, and purified by two recrystallizations from ether-alcoho1.2 Inorganic and other test reagents were standard laboratory grades. Temperatures were not controlled; the probable range of test-solution temperatures is 650 to 80°F.

Jan 1, 1943

By E. E. Malouf

With the continued development of low-grade porphyry copper deposits by open pit mining, substantial amounts of copper-bearing strip material have been accumulated in waste dumps adjacent to the many large mines. Since the end of World War II, the production of copper from leaching these copper-bearing wastes increased from approximately 4% of the total copper production to 10% by the early 1960's. Projected increases will probably raise this figure to 20 to 30% by the early 1970's. Furthermore, a gradual recognition of the economic feasibility of leaching mined-out areas is evident and will undoubtedly contribute additional production. Waste dumps in canyons and gulches on the periphery of open pit mines, mine stopes, caved areas, and abandoned open pits often contain substantial quantities of leachable rock ranging in concentration from 0.1 to 0.4% copper. Recent developments in the leaching of copper, mainly the recognition of bacterial oxidation of sulfide minerals combined with better under- standing of the control of the salt content of the leach solutions, both by adjusting the pH and/or by hydrolysis, are resulting in a greatly expanded recovery of copper from these hitherto uneconomic mine rejects. 11.5-1. Mechanism of Leaching. Leaching processes for the extraction of metal values from mine ore or waste may be classified for convenience as either chemical leaching or bacterial leaching. Chemical leaching is considered to be the extraction of soluble salts by metathesis in acidic, basic, or neutral water solutions. The reactions involved may be evaluated by chemical thermodynamics. Bacterial leaching, although a chemical process, is dependent on biological catalysis and this is generally a much more complex process. This justifies its separate treatment in the application to leaching. Acid ferric sulfate solutions are commonly employed in the mining industry to leach valuable metals from metal sulfide ores. The leaching mechanism is a reduction-oxidation reaction in which minerals are oxidized at the expense of ferric sulfate. Such chemical leaching is profitable when

Jan 1, 1968

By Thomas D. West

A short time ago, I had occasion to cast iron plates 1 in. thick, direct from metal containing Si, 0.51; 8, 0.045; Mn, 0.75; and P, 0.094 per cent. Much to my astonishment, I found that there was no trouble in planing them; whereas, if cupolaimetal of like composition had been used,*the planing would have been a difficult operation. I have often noticed a greater fluidity or " life " in furnace-metal, as compared with the cupola-product. Iron can be seen flowing down the furnace-runners from 50 to 100 ft., and reaching the last pig-bed in satisfactory condition, while cupola-metal might have solidified before it had flowed so far. I have seen Bessemer iron, which, on account of its low phosphorus-content, does not have the " life " of ordinary foundry-iron, held in a 30-ton ladle for nearly an hour and a half; and after skimming off the coke-dust, it still had to be cooled off' considerably before being cast. As a general proposition, it is known that the lower sulphur-content and the frequently higher temperature of direct-metal, compared with the same iron remelted in the cupola, has much to do with its greater life; yet some problems connected with this phenomenon seem to call for further study. For instance, furnace-metal containing more than 1 per cent. of silicon holds carbon, which is separated later as "kish." This separation does not take place to any great degree while the metal is very hot; but during its gradual cooling, at times, the kish is given off in such large quantities as to cover the ground from 20 to 30 ft. around the ladle. In making castings of direct-metal, especially with a high content of silicon, the separation of kish becomes an annoyance. Perhaps this throwing out of the excess of carbon makes the life of the metal shorter, after it has been remelted in a

Jan 1, 1905

By G. Derge, Lo Ching Chang

The chemical and physical propertties of slag systems are of special interest to metallurgists, for nearly all metals are in contact with molten slags during the primary reduction from their ores and then during the subsequent refining and alloying processes that determine their ultimate use. These processes are carried out at high temperatures and involve such complex chemical systems that funda-mental scientific knowledge of the Properties and behavior of these slags is inadequate. Various hypotheses have been Proposed to explain known slag characteristics. The commonest of these regard the molten slag as constituted of compounds that are dissociated in varying degrees into their constituent oxides, as illustrated by Schenckl and the recent Papers of Chipman and co-authors. Another proposal is that these compounds dissociate by com-plete6 or partial ionization, the evidence for which has been reviewed by Martin and Derge.? whatever hypothesis is favored, the exact formulation of these compounds is incomplete. It is based on three principal types of information: 1. Studies of solidified 51% samples by X ray diffraction, petrography, and similar methods that can be used at room temperature. The correlation of this information with the high-temperature properties of the molten slag is uncertain. 2. Studies of slag-metal equilibria, which have the advantage of providing observations on the molten slag at high temperature. However, even these data present problems of interpretation because they require a complete knowledge of the metal phase. 3. Direct measurements of properties of molten slag at the temperature of greatest metallurgical interest. Viscosity, electrical conductivity, specific heats, and similar properties have been measured, but the data of this type are widely scattered and frequently difficult to interpret. Additional direct measurements of properties of molten slag that can be interpreted in terms of chemical behavior are required, and this paper shows that the standard physical-chemical measurement of reversible electrode potentials, which measure the activity of specific constituents, is a fruitful source of such information. The purpose of this investigation, therefore, was to find an electrode combination that would yield reversible electromotive force measurements when dipped into the molten slag to be studied. Slags of the systems cao-sio2 and cao-120,-SiO2 were chosen for study because graphite containers could be used and the data could be correlated with those for viscosity, conductivity, and other proper-

Jan 1, 1948

By G. Derge

The chemical and physical propertties of slag systems are of special interest to metallurgists, for nearly all metals are in contact with molten slags during the primary reduction from their ores and then during the subsequent refining and alloying processes that determine their ultimate use. These processes are carried out at high temperatures and involve such complex chemical systems that funda-mental scientific knowledge of the Properties and behavior of these slags is inadequate. Various hypotheses have been Proposed to explain known slag characteristics. The commonest of these regard the molten slag as constituted of compounds that are dissociated in varying degrees into their constituent oxides, as illustrated by Schenckl and the recent Papers of Chipman and co-authors. Another proposal is that these compounds dissociate by com-plete6 or partial ionization, the evidence for which has been reviewed by Martin and Derge.? whatever hypothesis is favored, the exact formulation of these compounds is incomplete. It is based on three principal types of information: 1. Studies of solidified 51% samples by X ray diffraction, petrography, and similar methods that can be used at room temperature. The correlation of this information with the high-temperature properties of the molten slag is uncertain. 2. Studies of slag-metal equilibria, which have the advantage of providing observations on the molten slag at high temperature. However, even these data present problems of interpretation because they require a complete knowledge of the metal phase. 3. Direct measurements of properties of molten slag at the temperature of greatest metallurgical interest. Viscosity, electrical conductivity, specific heats, and similar properties have been measured, but the data of this type are widely scattered and frequently difficult to interpret. Additional direct measurements of properties of molten slag that can be interpreted in terms of chemical behavior are required, and this paper shows that the standard physical-chemical measurement of reversible electrode potentials, which measure the activity of specific constituents, is a fruitful source of such information. The purpose of this investigation, therefore, was to find an electrode combination that would yield reversible electromotive force measurements when dipped into the molten slag to be studied. Slags of the systems cao-sio2 and cao-120,-SiO2 were chosen for study because graphite containers could be used and the data could be correlated with those for viscosity, conductivity, and other proper-

Jan 1, 1948

By Pei-Yung Huang, Carle R. Hayward

IN order to understand more fully the actual state of copper lost in copper reverberatory slags, a systematic study on the various reactions between certain metallurgically important copper compounds and synthetic copper reverberatory slags was undertaken by the authors in the Massachusetts Institute of Technology from 1942 to 1945.1 This paper, being only a part of the work completed, is published first because it furnishes the first experimental evidence of the formation of copper ferrite from reactions between cuprous oxide and copper reverberatory slags. CHOICE OF SLAG COMPOSITION The choice of the composition of the synthetic reverberatory slags to be used was much deliberated. Commercial copper reverberatory slags, neglecting minor constituents, average:2.3 45 to 47 pct FeO; 38 to 42 pct Si02; 5 to 6 pct CaO; 5 to 6 pct A1203. Since the ternary system CaO-FeO-SiO2 has been much more thoroughly studied4 and is much simpler than the quaternary system CaO-FeO-Si02-A1203, it was decided to use calcium oxide only instead of calcium oxide and alumina in the synthesis of the slags. Fortunately the composition of the average copper reverberatory slag with calcium oxide substituted for alumina lies in the region of the phase diagram clarified by the investigators. A survey of the phase diagram (Fig I) suggested two compositions: (I) the com¬position near the invariant point S, which is made up of 46 pct ferrous oxide, 37 pct silica and 17 pct calcium oxide; (2) the composition near the invariant point K with 45.5 pct ferrous oxide, 43 pct silica and 11.5 pct calcium oxide. Composition S has the advantage that the percentages of ferrous oxide and of silica almost exactly coincide with those of the average reverberatory slags, and that of the lowest melting point (1093° ± 3°C) in the whole ternary system. The calcium oxide content, however, obviously is high. Since we have already substituted calcium oxide for alumina, and since calcium oxide is more basic than alumina, the resulting slag is decidedly too basic. Composition K has a slightly higher melting point (1105° ± 3°C) and a higher silica content, but this is preferred because the slag is saturated with respect to tridymite and thus should not corrode siliceous refractories. Besides, it is less basic than composition S. The final slag composition, therefore, was chosen to

Jan 1, 1947