Search Documents

By A. E. Powers

YEARS of experience and research have shown that molybdenum, tungsten, and vanadium are among the most useful and effective elements in augmenting the high-temperature strength of heat-treatable, ferritic steels. Grün, for example, in conducting an early survey of the strengthening effects of various elements in annealed, low-carbon steel at 750° and 930°F (400° and 500°C), found molybdenum and vanadium to be the most effective.' Holtmann comprehensively studied the strengthening effects of molybdenum and vanadium in quenched and tempered steels at 930°F as a function of microstructure and carbon content.' He found creep strength to be related to the saturation of the austenite at the austenitizing temperature, such that strength is increased by alloying until the y loop is reached—the terminus of complete austenitization. Beyond this degree of alloying, the inability to heat treat will result in lower strength, at least for low and moderate creep temperatures. Tungsten, owing to higher cost than molybdenum, has been little used in ferritic high-temperature steels. As a result, very few investigations have been made of its high-temperature strengthening ability, and reliable data on its effectiveness are not available. Grün rated tungsten far less effective than molybdenum at 930°F (500°C) on a weight-percentage basis.' However, Tammann has found that tungsten is as effective as molybdenum in raising the recrystallization temperature of iron. For this reason Smith, in a review of the subject, has advocated a re-examination of the influence of tungsten on the high-temperature strength of steel.' In any study of the effects of alloying additions on high-temperature properties, recognition must be made of the many variables involved, some of which can be controlled but have been ignored in innumerable investigations of the past, and some of which are difficult or even impossible to control. One cannot, for example, assign a definite strengthening index to any one alloying element, for this will be dependent upon the microstructure (heat treatment and mechanical treatment), testing con- ditions (temperature, time, and stress), and the complete composition of the steel (accompanying alloying elements, impurities, etc.). One ever-appear ing variable, hardness or tensile strength at room temperature, may be eliminated by heat treating all of the alloys to a single hardness level. An attempt may be made to control the variable of primary quenched structure by oil or water quenching the test specimen. The control of such variables may not be possible in cases of widely varying compositions, but at least such deviations should be recognized. Material and Procedure The alloys, made as 30-lb ingots in an induction furnace, all had the same base composition of about 0.18 pct C, 0.85 pct Mn, and 0.48 pct Si. They were grouped as follows: Mo Group—Containing up to 5.2 pct Mo. W Group-Containing up to 6.0 pct W. V Group—Containing up to 3.3 pct V. Mo-V Group—Containing up to 2.7 pct Mo and up to 1.4 pct V. Mo-W Group—Containing up to 2.5 pct Mo and up to 2.5 pct W. The steels, listed in Table I, were forged to ¾ in. sq bars and the material for the high-temperature, rupture-test specimens was further swaged to %-in. round bars.

Jan 1, 1957

By Morris E. Fine, Richard A. Kloske

The stress-strain beha1,ior in tension of Au-Ag alloy single crystals containing nominally 1,3, 5, 95, 97, and 9.9 at. pct Ag was studied uS strain role and lektlperalure down lo 4.2K. A slrain aging yield hob lc,rrs observed on aging under stress in the temperature range 30° lo 75°C. The species diffusing to the dislocation is thought to be a divacancy-solute complex wilh /he. solute then pinning the dislocation by short-Range ovdering and possibly Suzuki locking. At room tempevullcve the critical reso1ved shear stress .follo~c.s an empirical equation of the form tc = A +Bc' where A and B are 90 and 420 ,g per sy mm tor gold base alloys and 60 and 510 g p~r sq )11ttz .tor si1ver base alloys. This strengthening was attributed to a long-range size ejtect. The alloy slrenglliening at i.2'K is greafer than at room temperature. The additional atrloutzf was altribuled lo a uwak skovl-range i?~levacIion between the solute and dislocallon cove. The activation energy .tor deformation a/ 4.Z0h7 decreases on alloying. 11 increases irr other fee systetns. hi the 5 at. pcl Air-Ag- alloy in pmvlicular there is very extensive easy glide and lavge overshooting- of the synmetry line at 4.Z°K. There is also u sharp decrease in the vale of. strain hardenitlg near the widdle of stage II with the new rate bezng abold the sarne as tlzal In easy glide. This uws attributed to a sudden reduction of activity on the pvitrrarg sgstertr. In Au-Ag alloys the critical resolved shear stress Tc. at room temperature is essentially a parabolic function of atomic concentration:' the 50 at. pct Ag-50 at. pct Au alloy is about 10 times stronger than the pure metals. This strengthening occurs in spite of the similarity in valence and atomic size. Solid-solution strengthening in fcc metals is characteristically greater at low temperatures than at room temperature. In Ag-10 at. pct Au and Au-10 at. pet Ag; r, (20.4K)/Tc (300°K) is 2.3 and 2.5. respectively.- compared to 1.2 in pure silver.3 Suzuki' and Flinn5 explained the alloy strengthening at room temperature as a combination of Suzuki locking and short-range order hardening. The agreement between the computed and measured strengthening was very good: however, in Ag base-A1 alloys Hendrickson and Fine6 concluded that Suzuki locking resulted mainly in a yield drop effect. Recent reviews of the solid-solution strengthening in fcc metals by Fleischer2 and Haasen8, 9attributed the strengthening at room tenl-perature to the combined effect of atom nlisfit and change in shear modulus 011 the long-range stress field surrounding a dislocation. The parameter used by Fleischer was The shear tnoduli of Ag-0 to 6 at. pct Au alloys were measured by Pur-wins. Labusch. and Haasen.In While addition of 4 at. pct Au caused an appreciable increase in the C,, elastic constant. there was a decrease on increasing the solute to 6 at. pct Au: C,, and C :: were not measured in the 6 at. pct alloy. The greater solution hardening at low temperatures implies the presence of short-range interactions between the solute atoms and dislocations These include size and electronegativity effects. Whether the extra alloy strengthening at low temperatures is due to locking or friction hardening is still a controversy."".' In the present research the stress-strain behavior of Au-Ag single crystals containing 1 to 5 at. pct Ag and 1 to 5 at. pct Au was measured vs strain rate and temperature down to 4.2' K. Particular attention was paid to yield drop effects. These have not been previously reported. PROCEDURES The alloys were supplied by the Engelhard Industries. Inc.. as strips 0.050 by 0.250 by 12 in. The compositions are given in Table I. Single crystals were grown under static vacuum using a traveling molten zone technique. Crucibles shaped to the size of the strips were made of high-purity graphite prebaked for 24 hr at 1100°C in vacuum. The crucible and its charge were placed in

Jan 1, 1970

By Frederick Prime

The first catalogue of Geological Reports of the United States was prepared by Prof. 0. C. Marsh, and published in the American Journal of Science and Ark for 1567, vol. xliii, second series. Since then the list has more than doubled, and it was thought that the publication of a new catalogue, brought clown to date, would be useful to many of the members of the Institute of Mining Engineers. The compiler will be most thankful to have any omissions or inaccuracies in the list sent to him, to be published as a supplement in the next volume of the Transactions. Especially to have the correct title, number of pages, plates, and maps of any volume on the list to which an * is prefixed, as he has been unable to personally consult such works. A preliminary list was issued last February, which has been almost doubled by the kindness of many friends. The writer desires more especially to express the obligations he is under to the following gentlemen : The Chief of Engineers, U. S. A.; Principal Dawson, Mr. G. M. Dawson, Drs. R. J. Harrington and T. Sterry Hunt, of Montreal; Mr. H. Engelmann, of La Salle, Ill.; Dr. F. V. Hayden and Prof. J. W. Powell, U. S. Department of the Interior; Prof. E. W. Hilgard, University of California; Prof. Henry Y. Hind, Windsor, N. S.; Prof. C. H. Hitchcock, of Dartmouth College; Mr. Henry A. Holmes, State Librarian, Albany; Maj. Jed. Hotchkiss, Staunton, Va.; Prof. W. C. Kerr, Raleigh, N. C.; Dr. J. S. Newberry, of Columbia College ; Prof. W. H. Pettee, of the University of Michigan ; Dr. Samuel H. Scudder, Prof. N. S. Shaler, and Prof. J. D. Whitney, of Harvard College; Mr. Sanderson Smith and Prof'. J. J. Stevenson, of New York; Mr. Addison Van Name, of Yale College, and Lieut. Geo. M. Wheeler, U. S. Engineers.

Jan 1, 1879

By E. T. Turkdogan, J. H. Swisher

The solubility of oxygen in zone-refined iron was determined in the temperature range.from 881" to 1350°C. The solubility in a iron at 881°C ms found to be about 2 to 3 ppm; in y iron, the solubility was found to increase from about 2 to 3 ppm at 950°C to about 25 ppm at 1350°C. The permeability of oxygen in an iron -0.1 pct Al alloy was determined in the y iron range, using an internal oxidation technique. By combining the permeability and solubility data, the diffzisivity of oxygen in y and a iron was calculated. The oxygen diffusivity in solid iron may be s~immarized as follows: 8820 For 6 iron and IN a recent paper, Hepworth, Smith, and Turkdogan1 reported on the solubility, permeability, and diffusivity of oxygen in 6 iron, together with permeability data for oxygen in a iron. In the present investigation, similar measurements were made in the ? phase region. In addition, a solubility measurement was performed in the a phase region to permit calculation of the diffusivity of oxygen in a, iron. References to early work on this subject are given in the previous publication.' EXPERIMENTAL Solubility Measurements. The oxygen solubility was determined by equilibrating cylindrical samples 0.3 in. diam by 14 in. long of zone-refined iron in water vapor-hydrogen gas mixtures. The zone-refined iron was prepared by B. F. Oliver of this laboratory, using an apparatus and technique described elsewhere.2'3 Six zone-melting passes were used to achieve a total impurity level of about 30 ppm. Of this 30 ppm, the combined nickel and cobalt content was about 20 ppm, oxygen was 4 ppm, and all oxidizable impurities less than 1 pprn each. A vertical resistance furnace wound with molybdenum wire was used for the experiments. The temperature was measured before and after each experiment with a Pt/Pt-10 pct Rh thermocouple. In the gas train, flow rates of hydrogen and argon were measured with capillary flow meters, and the resulting mixtures were passed through a column containing 90 pct oxalic acid dihydrate and 10 pct anhydrous oxalic acid to obtain predetermined ratios of H2O to H2. The vapor pressure of H2O above this mixture as a function of temperature is well-known.4 The exit gas was ana- lyzed periodically for H2O, and good agreement (+3 pct) with the calculated composition was obtained. The zone-refined iron specimens were held in the furnace for a sufficient length of time for equilibration, e.g., 18 hr at 1350°C and 1 week at 881°C, then quenched in a brine solution. After removing the surface oxide from the samples by machining, duplicate analyses were obtained by a combined vacuum fusion-infrared method; oxygen analysis was reproducible within 2 ppm. Permeability Measurements. The permeability of oxygen in alloys containing about 0.1 pct A1 was determined by internal oxidation and measurement of the subscale thickness as a function of time. The experimental alloys were prepared by adding aluminum to electrolytic iron (grade 104A plastiron) that had previously been vacuum-carbon deoxidized. The resulting ingots contained about 20 ppm O, 100 pprn C, 40 pprn Si, 50 ppm Mo, 20 ppm P, 20 ppm S, and 20 pprn Zr as the principal impurities. After hot rolling the ingots to 1-in.-thick slabs, specimens were machined from the stock in the form of rectangular plates, 4 by 5 by 2 in. The general procedure for the permeability experiments was the same as those for the solubility measurements. The specimens were cooled in a reducing atmosphere rather than quenched, however, in order to maintain a clean surface for measurement of the sub-scale thickness. This measurement was made on a polished cross section of each specimen, using a microscope with a micrometer stage. The inclusions formed at the lowest temperature 1033°C were too small to be seen with an optical microscope. An electron micrograph showing the size and shape of individual particles is shown in Fig. 1. The dark band in the picture is a boundary between two subgrains. The subscale thickness in these samples was measured with an optical microscope after heavily etching in 2 pct nital, which gave contrast between the subscale and the unoxidized zone.

Jan 1, 1968

By A. C. Freeze

The first use of electric punched card accounting machines as an aid in calculating reserves at the Sullivan mine in Kimberly, B.C., was made in January, 1948. At that time their use was limited to totalling individual reserve blocks for the various reserve classes and for calculating total metal content. The immediate objective was to increase speed, improve accuracy, and to effect some savings in labor that could be employed more usefully elsewhere. It was recognized also that the potential for achieving even greater advantages was excellent. The initial experiment proved so successful that it was inevitable that the use of the method would expand. Thus, for the past nine years assay data from core hole and development headings have been processed by these machines and the results integrated with the program of calculating reserves. It was also learned that the machines could store and classify a large amount of other information concerning the mining characteristics of each reserve block in addition to tonnage and metal content. This has proven very useful for the preparation of monthly production reports as well as in long term planning, in forecasting production schedules, and in analysing the results achieved.

Jan 4, 1961

By F. W. McQuiston

Teamwork is the key to an efficient organization. Cooperation among mining staff members is an obligation owed to the company. The more cooperation the metallurgist receives from underground, the higher milling yield will be, which in turn makes for a greater mine profit. There is no pay for metal left in mill tailings. The metallurgist is not in a position to be of help to either the geologist or mining engineer, but can receive valuable assistance from both. Therefore, the metallurgist must win underground cooperation. The mining engineer is usually interested in geology because of its relation to ore control; in milling because that is where the rock goes. However, any overlapping of interest between geologist and metallurgist is quite remote.

Jul 1, 1956

By M. L. Holzworth, Joseph C. Kremer, Paul A. Beck, L. J. Demer

FOR alloys which are in practice heat treated to obtain increased strength, such as steels, duralumin, copper-beryllium, and others, the treatment usually involves heating to a relatively high temperature. At such temperatures the grain size of the product is largely determined by grain growth. Even in metals and alloys annealed merely to relieve work hardening, recrystallization is generally followed by a certain amount of grain growth. Thus, effective grain size control, which is often of great practical importance in manufacturing processes, depends on the grain growth behavior of the material used. Despite its importance, grain growth has been the subject of few investigations of a fundamental nature. The term "grain growth" has been used to designate a group of related, but distinctly different, phenomena. The two most important and best known of this group are illustrated by the following example. Curve a in Fig r shows the increase of the average grain size of a copper-beryllium alloy, containing 2 pct Be and 0.15 pct Co, with increasing annealing temperature. The time of annealing was 2 hrs. The grain size was quite uniform in all specimens. The results of a similar experiment with an alloy containing 2 pct Be and 0.31 pct Co are shown by curve b. It is seen that for any annealing temperature below T. the grain size was smaller than in the previous case. Grain growth became slower with the higher Co content. This "inhibiting" effect of the higher Co addition was associated with the appearance in the microstructure of fine, light blue particles of the CoBe phase. Up to temperature T. the structure of the inhibited alloy (curve b) was just as uniform as the structures represented by curve a. However, after annealing at T, or at higher temperatures, the inhibited alloy showed some extremely large grains (much larger than the grain sizes developed by the uninhibited alloy with low Co content) mixed with the small grains according to curve b. The presence of these mixed or "duplex" structures is indicated in Fig 11 by the vertical lines branching off curve b. The type of grain growth occurring in uninhibited Cu-Be alloys (curve a) has has been most frequently and best investigated in brass. This type has been designated as "normal grain growth," while the grain growth phenomena occurring in inhibited materials were, at times, referred to as "abnormal grain growth." However, since the latter term has been applied occasionally to the phenomenon of critical recrystallization, which also results in large grains although by an entirely different mechanism, in the present paper a different nomenclature has been adopted in order to avoid confusion. Typical of the grain growth in uninhibited metals and alloys is the continuous

Jan 1, 1947

The first discovery of gold in Montana is credited to François Finlay, a half-breed, from the Red River country, in Canada; he went to California during the early days and learned there how to wash the gold from placer deposits; then, on his return, he crossed Montana and found gold on the western slope of the Rocky Mountains, on Gold creek, a minor tributary of the Hell Gate river, in what is now Deer Lodge county. That was in 1852.* Finlay did not find enough gold to induce him to continue at work, but six years later a group of miners, led by the brothers James Stuart and Granville Stuart prospected on this same creek, obtaining about ten cents to the pan. They, however, were harassed by the Blackfeet Indians, and they were also handicapped by lack of proper tools; so they too desisted from further operations. Two years later, in 1860, Henry Thomas started to work on Gold creek with three sluice-boxes hewn out of green timber that he cut on the spot. With this simple apparatus he won from $1.50 to $2.00 per day. This may be considered the fist instance of systematic mining in Montana. Meanwhile the Stuarts went to Fort Bridger, in southwestern Wyoming, where they remained as traders until 1861, when, again lured by the gleam of gold, they returned to the valley of the Deer Lodge and resumed prospecting, using 10 sluice-boxes that were brought from Walla Walla, in Washington, 425 miles distant. In the summer of 1862 they were joined by many others, chiefly from Colorado, in consequence of an exchange of

Jan 1, 1932

By Robert Glass Cleland

THE THIRD and most important item on the Phelps Dodge agenda for the development of new ore supplies involved the site of the company's initial venture into Arizona, the old mining camp of Morenci. By the purchase of the Arizona Copper Company's holdings in 1921, Phelps Dodge had obtained control of virtually the entire Morenci district, including town, public utilities, and, above all, the huge mineralized area that had once been divided between numerous competing companies. Because of this rigid concentration of ownership in the hands of one organization, Phelps Dodge was able to plan and successfully carry out a program of greater magnitude than any Arizona mining company had previously under- taken. The immense deposit of low-grade ore, usually referred to as the Clay Orebody, had been known to the mining companies of Morenci for many years. Pioneer exploratory work, both by the Arizona Copper Company and later by Phelps Dodge, revealed that the deposit, mostly of light-gray porphyry rock, lay under a hard capping from two hundred to five hundred feet thick. An intensive drilling

Jan 1, 1952

By Shosei Serata

Stress control methods of mining have been developed separately in at least four different parts of the world in entirely different types of mining -- coal, trona, salt and potash -- during the decade of the 1960s. They all utilized yield pillars as tools for ground control. Today, yield pillars are becoming widely used in under- ground mines in a variety of geological conditions. Stress control methods are effective in stabilizing openings in weak, complex grounds, especially at greater depths. Their advantage is that they utilize existing ground media to stabilize mine openings by altering the stress distribution patterns around the openings, by controlling design parameters such as room width, pillar geometry, and excavation sequence, rather than by using a conventional means of artificial ground support such as roof bolts, cribbing, or arches. Stress control methods, therefore, are suitable for both advance and retreat mining, including total extraction mining. Adaptation of these methods results in substantially greater safety, productivity, and ecnomy over conventional methods. These methods are based on scrutiny of the actual stress conditions in the ground, by both in-situ measurement and computer simulation. This paper provides a summary of stress control methods as developed over the last ten years. The field examples are limited largely to salt and potash mining applications, although the method has been used successfully in other mining applications. The examples illustrate that stress control methods actually address general ground weakness problems -- separation at discontinuity planes, swelling by shale expansion, deterioration by brittle fracture, and interference by ground water. That is, although the principle is developed mainly with reference to salt and potash applications, it is generally applicable to weak ground.

Jan 1, 1983

By E. O. Wagner, V. F. Parry, W. S. Landers

Development work has shown that the yield of primary tar from coal is proportional to the heat in the volatile matter of the coal and that the yield of tar from noncoking coals may vary from 10 to 45 gal per ton on the ash-free and moisture-free basis. Pilot plant operations have proved that 100 to 135 pct of the bench-scale carbonization-assay yield of tar can be obtained. FOLLOWING investigations by the Denver Bureau of Mines on drying fine coal in the entrained state,'. ' Texas Power & Light Co. employed the fluidized technique to upgrade Texas lignite for use in power plants. Because of the rapidly rising cost of natural gas in Texas the company agreed to cooperate with the Bureau of Mines in studying further the upgrading of lignite by low-temperature carbonization, since potential value of the tar would help offset the cost of fuel. Considerable interest was aroused, therefore, when Aluminum Co. of America decided to use dried lignite in its 240,000-kw power plant at Rockdale, Texas, operated by Texas Power & Light. Carbonization of coal before burning in a power plant is not new. Plants in Germany have been operated for many years on carbonized brown coal and lignite briquets produced in large integrated plants. Large-scale experiments in carbonizing pulverized coal with hot flue gases were made 30 years ago at Milwaukee," and many inventors have proposed other processes. In the U. S., technical and economic problems have prevented successful operation of large plants on carbonized coal. but new techniques of handling solids in fluidized beds may overcome these difficulties, particularly if the higher volatile noncoking coals are used. Any bituminous material will decompose when heated to about 900°F to yield primary tar, gas, and char. The quantity of tar obtained from various coals depends on their rank and volatile content and to some extent on rate and method of heating. The liquid products derived from thermal decomposition of peat, brown coal. lignites, oil shale, and noncoking bituminous coals can be easily liberated by rapidly heating these materials in a fluidized bed at about 500°C (932°F). Since it takes only a few minutes to heat small particles of fuel to carbonizing temperature in a fluidized bed, processing plants can be built to handle up to 50 tph at relatively low cost. The pioneering development work being conducted at Rockdale, Texas, by Alcoa and Texas Power & Light will solve many engineering problems of such operations. The Bureau of Mines at Denver has studied the carbonizing properties of several hundred coals by small scale assay at 500°C, deriving a simple correlation between the potential yield of tar and the proximate analysis. This correlation, shown in Fig. 1, compares the heat in the volatile matter of the coal with the potential yield of primary tar. The yield of primary tar varies from 12 to 50 gal per ton of pure coal." About the same amount of heat is needed to * MAF equals moisture-and-ash-free basis. distil any dry coal at 500°C, and the time required to carbonize a given particle size is about the same for any coal. It is therefore obvious that coals rich in volatile matter will show the greatest profits when processed. Texas lignites are rich in volatile matter, which contributes some 5700 Btu per lb of MAF coal, and the potential primary tar and oil yield from this lignite averages 12 pct by weight or 27 gal per ton from the pure lignite. Texas lignites are considerably richer in potential tar than lignites of North Dakota and Montana. During 1950 the Bureau of Mines conducted many experiments on carbonizing fine dry coal in the entrained state, publishing a report4 n major features of pilot and commercial-size units required to carry out the process. Additional experimental work has been done at Denver and the pilot plant has been improved, particularly the facilities for studying removal of fine dusts from tar vapors and gases at high temperatures by electrostatic precipitation. A number of materials have been carbonized, including sawdust, peat, brown coal, Brazilian oil shale, lignites, and the lower rank bituminous coals having noncoking properties. Straight coking coals cannot

Jan 1, 1957

NEW YORK MEETING PAGE Winchell, H. V.-Geology of Pachuca and El Oro, Mexico. Discussed by Frederick MacCoy, Robert Hawxhurst, Jr 2 WILKES-BARRE MEETING Kynor, Herbert D.-Mechanical Mining of Anthracite. Discussed by C. Evans, Jr., S. J. Jennings, W. J. Richards, Geo. S. Rice, and the author 3 Stein, C. H.-Ashley Planes for Handling Freight Traffic. Discussed by Graham Bright, Douglas Bunting, S. J. Jennings, R. V. Norris, C. H. Strange, Edwin Ludlow, W. J. Richards, and the author 3 Markle, Donald.-Anthracoal: A New Domestic and Metallurgical Fuel. Discussed by William Griffith, Edwin Ludlow, E. M. Chance, Charles Dorrance, E. W. Parker, G. H. Ashley, C. A. Burdick, Geo. S. Rice, and the author :.. 7 Griffen, John.-Slush Problem in Anthracite Preparation. Discussed by Henry Flood, Jr 11 Eavenson, H. N.-Lynch Plant of United States Coal and Coke Co. Discussed by E. V. d'Invilliers, C. Evans, Jr., Graham Bright, Geo. S. Rice, Geo. Otis Smith, A. M. Rodgers, C. T. Starr, C. A. Burdick, and the author 15 Bunting, Douglas.-Mine Fires Extinguished by Sealing. Discussed by Geo. S. Rice, J. B. Warriner, H. H. Otto, Edwin Ludlow, E. M. Chance, F. B. Nold, H. M. Chance, W. L. Jacobus, J. A. S. Ritson, R. D. Hall, Geo. S. Rice, and the author 18 Bright, Graham.-Determination of Electrical Equipment for a Mine Hoist. Discussed by F. L. Stone, Geo. S. Rice, L. F. Mitten, and the author 34

Jan 12, 1921

By David White

In these days, when detailed investigations of stratigraphy, structure, and sand conditions so frequently result in the discovery of new oil fields, and applause from oil companies and the public, geologists do well to walk humbly, and punctiliously to admit that the geologic principles controlling the distribution of oil and gas have as yet been discovered only in part, and that what remains yet to be learned is probably vastly more than what is already known. The few experiments already attempted have been fragmentary, and somewhat desultory, and however positive each of us may be with respect to certain theoretical conclusions, many of the fundamental questions as to the origin and mode of occurrence of petroleum are subject to radical disagreement. Of the chemical changes attending the generation of petroleum from organic matter, little is actually known. Most of the postulated formulas are liable to be misleading, through ignorance of essential factors. Open-minded-ness is therefore a prime essential at the present stage of our science. Nevertheless, adopting the hypothesis that oil originates in some manner fundamentally connected with the organic theory, and in possible departure from such open-mindedness, the writer will pay no attention to the so-called inorganic theory, since every attempt to apply this theory to the study of old oil fields, or to the discovery of new ones, affords cumulative evidence of its inadequacy. In this paper, some of the factors affecting the occurrence of petroleum that the writer believes worthy of consideration by the prospector for oil in any new region will be discussed. Some of these, which arc less generaLly understood, will be considercd somewhat in detail. Other points, the significance of which cannot now be determined, require more field study, and for that reason are here brought to the attention of the field geologist. On the other hand, certain theoretical points which do not bear especially on the oil possibilities of a new region will be given little or no attention. The main topics that will be discussed are: (1) sufficiency of carbonaceous detritus and residues in the oil-forming rocks; (2) stage of carbonization of the organic matter in the oil-bearing formations; (3) folding of the strata; (4) thickness of sedimentary formations; (5) conditions of deposition.

Jan 1, 1921

By James F. Kemp

The Bulletin of the Institute for March, 1911, is chiefly devoted to papers upon the iron ores of northeastern Cuba. At that time information about the new developments in the peculiar brown hematites of the region was becoming widely circulated and interest was especially keen. For some years exploration had been conducted with pits and trenches and so great an area had been shown to contain ore in the Mayari, Moa, and Cubitas or San Felipe districts, that the reserves conveniently situated for the consumption of American furnaces were estimated as quite two billions of tons. In the subjoined footnote will be found a list of the principal papers of special interest which have already been published.' The further remark may, however, be made that the

Jan 1, 1915

By H. Margolin, E. Ence

Two versions of the Ti-Mn binary diagram have been published recently.' , -0th diagrams show two compounds in the region between 40 and 70 wt pct Mn, but disagree as to the reaction in which these compounds are involved. The investigation of the manganese-rich portion of the Ti-Mn binary diagram was undertaken at New York University as part of an investigation of ternary systems with titanium and manganese in order to determine which of the proposed diagrams is correct. A number of alloys between 31 and 70 pct Mn were prepared in a manner similar to that described by Cadoff and Nielsen; except that low currents (110 amp in argon atmosphere) and long melting times (up to 20 min) were used to prepare the alloys. Compositions were determined from weight-loss data, assuming all loss as due to manganese. Heat treatments were carried out with relatively large pieces, since there was a tendency for manganese to be lost during heat treatment. When X-ray diffraction data was to be obtained, the central parts of heat-treated specimens were used to make filings or powders which were not heat treated. Specimens were heat treated from the as-cast state. Heat-treatment times were as follows: 1150°C, 1 day; ll00°C, 2 days; 1000°C, 5 days; and 900°C, 15 days. It should be noted that equilibrium was not attained at 900°, 1000°, and in one case, at 1150°C. Metallographic specimens were electrolytically polished and strain etched by a technique described elsewhere.' At least four, and possibly six, phases were found in the region investigated. On the basis of information available at this time, a completely self-consistent diagram cannot be constructed, and therefore data are presented only for those phases which have been identified by both X-ray and microstruc-ture. Of the compounds detected, the one highest in manganese is the Laves phase, TiMn,, which is hexagonal with a MgZn, type of structure.V he diffraction data for TiMn2 from a 70 pct Mn alloy annealed at 1150°C are shown in Table I. The c/a ratio and parameters of TiMn2 agree well with those of Wall-baum hnd Rostoker et al. The values obtained here are c/a = 1.641, a = 4.825A. Another compound is the y-phase which is estimated to contain about 60 pct Mn. The y-phase has a structure which is identical to that of TiMn, with c/a = 1.639, a = 4.906Å. The fact that y has a Laves-type lattice would suggest that TiMn, has a range of solubility which extends from the composition of TiMn2 (69.6 Mn) to that of y (60 pct Mn). However, this could not account for microstructures which, in the 60 to 70 pct Mn region, show several phases in both the as-cast state and after annealing at 1150°C. Fig. 1 shows a two-phase structure of a 60 pct Mn alloy annealed at 1150°C. The phases present are y (white) and e (dark). If y were TiMn, then, according to Rostoker et al.,' the second phase of Fig. 1 should be P-Ti. The diffraction data for the 60 pct Mn alloy of Fig. 1 are shown in Table I. The starred d-values are from the e-phase and these lines do not correspond to those of &Ti. Comparison of as-cast and 1150°C microstructures of the 60 pct Mn alloy indicates that e precipitated from y. Since y has a

Jan 1, 1955

By A. H. Tousley, C. L. Vickers

The author presents a history of the development of the Port of Long Beach from its beginning in 1905 to the present construction of a new bulk loading facility. In describing this new facility, emphasis is placed on such aspects as rail car and truck handling, gravity yard, rotary car dumping, bottom dumping, car dumping equipment, feeding and conveying, ship-loader-stockpiler, stockpiling and reclaim, dust control, and construction problems. Development of the Port of Long Beach, Calif. (see Fig. I), began in 1905. In that year private Long Beach interests acquired 800 acres of marshland in the Inner Harbor area and initiated a program of channel dredging and land reclamation. Efforts to establish a municipal port began a short time later and culminated in the opening of Pier 1 in 1911. An event of even greater significance to the port future also occurred in 1911. This was the tideland grant enactment by the state legislature that conveyed to the city of Long Beach all of the state's rights in the tidelands located within the city boundaries. The grant stipulated that all revenue produced from the tidelands be used for the development of navigation, commerce, and fisheries. During the next 15 years up to 1926, the port's commercial growth was steady, although relatively slow. During this period, several fundamental steps in the development of a major harbor were accomplished. These included the creation of the Board of Harbor Commissioners in 1917, the dredging of the Inner Harbor and entrance channel to accommodate deep draft vessels, and the correction of a serious silting problem through construction of the Los Angeles River Flood Control Channel. These efforts bore fruit during the ensuing 10 years in the establishment of more than $30,000,000 worth of industrial plants and private marine terminals in the Inner Harbor. Commerce over municipal wharves also increased more rapidly, and it became necessary to start the development of the harbor in a seaward direction. In 1936, oil was discovered in the harbor area, and the first Harbor Dept. well was brought in 2 years later. It soon became evident that the city of Long Beach would receive substantial revenue that, under the terms of the state grant of 1911, must be used in the development of the port. It was further realized that to properly guide and coordinate such development, a long range comprehensive plan was essential. The Board of Harbor Commissions contracted with G. F. Nicholson and J. F. Collins, consulting engineers, for the preparation of such a report that was completed in 1940. The Nicholson-Collins report proposed the development of an East Basin, between the entrance channel and the Los Angeles River, and a West Basin in the area now occupied by the Long Beach Naval Shipyard. Twenty full-size berths were to be provided in the East Basin and more than fifty berths in the West Basin. The report recommended extensive modern terminal facilities for handling waterborne cargo. Attention was given to improvement of the street and highway system to give better vehicular access and to avoid congestion within the port. To a large extent the recommendations of the Nicholson-Collins report were followed in the subsequent development of the East Basin. This development was greatly accelerated by World War 11, with its need for increased oil production and additional shipping facilities. The wartime and immediate postwar construction was largely concentrated on Pier A, with the development of Piers B, C and D following in more recent years. An important factor in the planning of these piers was their dual function as oil drilling sites and cargo piers. The Navy's acquisition of the West Basin area made it necessary to depart from the Nicholson-Collins plan and find other areas for future expansion. At the present time only one Inner Harbor Port-owned area having protected deep water frontage remains undeveloped. This is the property fronting on Channel 2 in the Inner Harbor acquired in December 1957, from Pacific Dock and Terminal Co. The growth of the port has been in a southerly direction since the construction of the Long Beach Naval Shipyard in the West Basin area. Recent extension of Piers F, G and J into the ocean follows typical port construction methods developed during the expansion of the Middle Harbor during the last 20 years.

Jan 1, 1963

By E. B. Harden, J. H. Harden

The practical use to which topographical models or relief-maps have been put, has within the last few years taken a wider range. They are rapidly coming into favor for other than purely scientific purposes, and their value for illustration and instruction is being more fully appreciated. Topographical maps; representing by contour-curve lines the elevations and depressions of the earth's surface, are now demanded in engineering work of nearly every description, and afford a ready means of bringing out the configuration of the country in a simple manner. A beautiful example of recent topographical mapping is seen in the seventeen sheets just issued by the Geological Survey of New Jersey. By reason of the inability of unskilled persons to understand the nature of a topographical map, it is sometimes necessary to con struct the same in relief, with the rivers, canals, railroads, etc., delin eated upon it. With the aid of such a map, problems in engineer ing science which would otherwise require expert assistance to explain them, are reduced to a simple and understandable form. Relief-maps are also of value to the geologist in working out the geological structure. To the instructor they present the most ready and efficient means of imparting clear and accurate knowledge of topography and kindred subjects. To the lawyer they are invalua ble in enabling him to bring into the court-room a representation of a part of the country with all its features accurately shown, to ex plain to the court and jury the special points about which litigation is pending and which would otherwise require long and laborious description. The application of the topographical map to business purposes is shown in a relief constructed by the writers for the Cumberland Valley Railroad Company and used by that company in the various ways of calling attention to the desirability of its route. This model is based partly on actual survey and partly on sketch topography. The horizontal scale is ,%, the vertical 1/19,200 of

Jan 1, 1888

By J. Rogers. K. L. Sutherland, E. E. Wark, I. W. Wark

Soaps have hem used as collectors for many years, but only in the last eight years have other long-chain paraffin salts been used. It may be anticipated that these newer collectors will be used mainly with nonsulphide minerals, for which the xan-thates and similar compounds are of little value. On the other hand, the xanthates are both cheap and effective for sulphide ores and seem likely to retain their present cminence in this field. During 1938 and 1939 two of us (E. E. W. and I. W. W.) commenced a comprehensive investigation of the principles underlying the use of paraffin chain salts as flotation reagents. This research was sponsored jointly by the University of Melbourne and a group of Australian mining companies. † A broad, semiquantitative survey was then made of the field covered in the present paper. This was followed in 1940 by further work by one of us (K. L. S.). In 1941 the investigation was taken over by the Division of Industrial Chemistry of the Commonwealth Council for Scientific and Industrial Research, Australia. Discovery of some principles upon which are based the flotation of minerals by paraffin chain salts was followed by their application in the development of processes for the recovery of certain strategic minerals from their ores. Promising results in the flotation of cassiterite from various ores will be described in a subsequent paper. The Paraffin Chain Salts 'he basic requirements for a "collector " in flotation are that it should form a film over the surface of the mineral to be floated, and that this film should be orientated so that hydrocarbon (nonpolar) groups form the effective surface. When modified in this way, the mineral surface possesses some degree of air avidity. All investigators would agree with Taggart, Taylor and Ince23 that such a film can be produced only if the collector compound contains an active (polar) group to attract it to the mineral surface as well as the nonpolar group. One section of this large class of polar-nonpolar compounds is the paraffin chain salts: CH3(CH2)nX where .X signifies a polar group that ionizes in aqueous solution. Though the compound can ionize, it may be a weak or a strong electrolyte, and the hydrocarbon chain may be in the cation or the anion (Table I). Many compounds of similar constitution are available, but the usual polar groups are: -Co2Na, -So3Na, -So4Na, — PO4Na2, or an aminonitrogen group, the

Jan 1, 1947

By E. E. Wark, I. W. Wark, J. Rogers. K. L. Sutherland

Soaps have hem used as collectors for many years, but only in the last eight years have other long-chain paraffin salts been used. It may be anticipated that these newer collectors will be used mainly with nonsulphide minerals, for which the xan-thates and similar compounds are of little value. On the other hand, the xanthates are both cheap and effective for sulphide ores and seem likely to retain their present cminence in this field. During 1938 and 1939 two of us (E. E. W. and I. W. W.) commenced a comprehensive investigation of the principles underlying the use of paraffin chain salts as flotation reagents. This research was sponsored jointly by the University of Melbourne and a group of Australian mining companies. † A broad, semiquantitative survey was then made of the field covered in the present paper. This was followed in 1940 by further work by one of us (K. L. S.). In 1941 the investigation was taken over by the Division of Industrial Chemistry of the Commonwealth Council for Scientific and Industrial Research, Australia. Discovery of some principles upon which are based the flotation of minerals by paraffin chain salts was followed by their application in the development of processes for the recovery of certain strategic minerals from their ores. Promising results in the flotation of cassiterite from various ores will be described in a subsequent paper. The Paraffin Chain Salts 'he basic requirements for a "collector " in flotation are that it should form a film over the surface of the mineral to be floated, and that this film should be orientated so that hydrocarbon (nonpolar) groups form the effective surface. When modified in this way, the mineral surface possesses some degree of air avidity. All investigators would agree with Taggart, Taylor and Ince23 that such a film can be produced only if the collector compound contains an active (polar) group to attract it to the mineral surface as well as the nonpolar group. One section of this large class of polar-nonpolar compounds is the paraffin chain salts: CH3(CH2)nX where .X signifies a polar group that ionizes in aqueous solution. Though the compound can ionize, it may be a weak or a strong electrolyte, and the hydrocarbon chain may be in the cation or the anion (Table I). Many compounds of similar constitution are available, but the usual polar groups are: -Co2Na, -So3Na, -So4Na, — PO4Na2, or an aminonitrogen group, the

Jan 1, 1947

By C. H. Chou, A. Sauveur

The senior author of this paper has expressed the belief that when gamma iron transforms into alpha iron on reaching the A3 point, each gamma grain does not change bodily into one or more alpha grains but that the alpha phase forms first at the boundaries and along the crystallo-graphic planes of the austenite grains.1 To quote: On cooling through the point As, at about 900° C, iron passes from the gamma condition to a new allotropic form generally designated as alpha. This transformation, however, is not instantaneous. There are good reasons for believing that it begins at the grain boundaries and along the octahedral planes of the crystals and that it progresses until each grain of gamma iron is changed into a grain of alpha iron, the resulting structure being similar to that of gamma iron. Were it possible to retain

Jan 1, 1929