Search Documents

By J. J. Crowe, G. K. Burgess

PAGE, Theories of Allotropy of Iron........... 667 Previous Determinations of A2 and A3 in Iron........ 668 Critical Ranges as Determined by Expansion........ 669 Critical Ranges by Thermoelectric Observations........ Critical Ranges in Terms of Crystalline Structure....... 670 Critical Ranges as Detected by Mechanical Methods...... 670 Critical Ranges as Given by Electrical Resistance....... 670 Critical Ranges as Determined Magnetically........ 671 Critical Ranges as Determined Calorimetrically....... 673 Critical Ranges from Heating and Cooling Curves....... 673 Summary of Previous Determinations of A3 and A2 in Pure Iron.... 675 The Present Investigation............ 678 The Experimental Method........... 678 Arrangement of the Apparatus.......... 679 The Measurements of Temperaturc.......... 679 The Measurement of Time........... 679 The Thermocouples............ 681 Temperature Scale and Calibration of Thermocouples...... 681 Mounting of Thermocouples........... 682 The Differential Measurements.......... 682 The Furnace and Accessories........... 682 The Vacuum Pump............ 683 The Energy Supply............683 The Rheostat.............. 683 The Materials Investigated............ 685 Sources of Iron............. 685 Preparation and Description of Samples......... 685 Chemical Analyses............. 687 The Experimental Data............. 688 The Preliminary Observations.......... 688 The Definite Series............691 Description of the Plotted Curves........... 694 The Effect of Plotting at Different Intervals........ 694 The Curves of the Definite Series.......... 695 . The Curves of the Preliminary Series......... The Existence of Other Critical Ranges......... 696 The Microscopical Examination........... 697 Summary and Conclusions............ 698 Bibliography............... 701 Plates................ 704

Jan 1, 1914

By J. E. Hilliard, J. W. Cahn

calculation has been made of the standard deviations to be expected in the measurement of volume fractions by areal analysis, lineal analysis and four point-counting Procedures. The effect of experimetztal errors is not included. Our conclusion is that a point count using a two-dimensional grid will be the most efficient method of volume fraction analvsis providing the grid spacing IS coarse enough. The predicted standard deviation for such an analysis is shown to he in good agreement with that determined experimentally. A metallurgist wishing to estimate a structural property by means of quantitative metallography is often faced with a choice between several different procedures. In such a case, he will naturally wish to know: a) Which procedure is the most efficient in the sense of requiring the least effort for a given precision? b) For a given procedure, what are the conditions for maximum efficiency? c) Under these conditions, how many measurements are required to attain a given precision? It is our aim in this paper to provide at least partial answers to these queries as they relate to the estimation of volume fractions from measurements on a random two-dimensional section of an opaque specimen. The commonly used techniques1,2 for volume-fraction analyses are based on one or more of the following principles: i) For an areal or Delesse3 analysis: That the areal fraction of a three-dimensional feature intercepted by a random plane provides an unbiased estimate of the volume fraction of that feature. ii) For a lineal or Rosiwal4 analysis: That the fractional intercept on a line passing at random through a two-or three-dimensional feature provides an unbiased estimate of, respectively, the areal or volume fraction of that feature. iii) For a point-count analysis: That the fractional number of randomly or regularly dispersed points falling within the boundaries of a two-dimensional feature on a plane, or within the boundaries of a three-dimensional feature in a volume, provides an unbiased estimate of, respectively, the areal or volume fraction of that feature. The absence of bias referred to in these principles does not, of course, imply that the results of an analysis will be free of error, but only that the expected result is equal to the true one. Application of the foregoing principles provide the following six possible experimental procedures: a) An Areal Analysis—This involves the measurement with a planimeter (or other means) of the area of a constitutent intercepted by the plane of polish b) A Two-Dimensional Random Point Count—Apos-sible experimental procedure for this analysis is to superimpose a sheet of transparent graph paper on a micrograph, and then use a table of random numbers to select coordinates for the points. c) A Two-Dimensiotuzl Systematic Point Count-Similar to b) except that the points are distributed in a prescribed manner, usually at the corners of a lattice superimposed on a micrograph or the screen of a projection microscope. d)A Lineal Analysis—A measurement of the fractional line length intercepted. It is usually performed by traversing the specimen under the cross hairs of a microscope and recording the distance travelled in each constituent. e) 4 One-Dimensional Random-Point Count— This could be performed by traversing the specimen with stops at random intervals to identify the constituent then present under the cross hairs. f) A One-Dimensionul Systematic Point Count— Similar to e) except that the traverse is stopped at prescribed (usually equal) intervals. It will be noted that the point-counting procedures b) and c) can be regarded as methods of estimating the areal fraction. Similarly, e) and f) are indirect methods of making a lineal analysis. All of the six procedures described above involve at least one stage of sampling. Thus, quite apart from any experimental errors, there will always be a statistical uncertainty associated with the final results. It is with the calculation of this uncertainty that we will be concerned. To avoid unnecessary repetition, the statistical relationships that will be used in the calculations are collected together in the appendix. For a fuller discussion reference should be made to one of the many textbooks5,6 on statistics. For symbols relating to the specimen structure we will follow as far as possible the terminology used by Smith and Guttman.7

Jan 1, 1962

By Harvey Brooks

Jan 1, 1963

By F. E. Buch

THE Smelter is designed for a production capacity of 10,000 short tons of blister copper per month, when operating on the present concentrate grade. The Smelter lay-out is shown in Fig I. The major units of equipment comprise two reverberatory furnaces, three 13 by 30 ft Peirce-Smith converters, two straight line casting machines, one being served by a 13 by 30 ft holding furnace and the other by a ladle tilting quadrant, two converter ,aisle cranes and two converter blowers. The plant is compact and the general arrangement of standard gauge railway tracks and conveyor belts provides for a smooth flow of incoming materials and metallurgical products. Concentrate is received by conveyor belts and fluxes in standard railway trucks. The local track system is covered by an electric trolley locomotive. The Smelter treats a wet (10 pct moisture) flotation concentrate containing approximately 53 pct total copper and 0.9 pct oxide copper. The predominating minerals are chalcocite, chalcopyrite and bornite accompanied by small quantities of malachite and cuprite. The gangue is highly siliceous and requires limerock as a flux. Metallurgy would be straightforward were it not for the necessity for eliminating k bismuth which occurs as an impurity in the ore along with the copper. Directly or indirectly most of the Smelter problems can be traced to the necessity for bismuth removal. Copper recovery, based on new copper treated, averages 97.5 pct. GENERAL DESCRIPTION Flotation concentrate, containing to pct moisture, is conveyed from the filter plant to the smelter storage bins by conveyor belts, the material being weighed in transit by a revolving drum type of weigh-hopper manufactured by Samuel Denison and Son, Ltd. The weigher consists of a steel drum with dished ends carried on a horizontal shaft and rotated by an 8 hp squirrel-cage motor through a worm and spur reduction gear. A feed mouth in the drum permits of filling and discharging. The whole unit is supported on a framework resting on weighing levers, which in turn connect to transfer levers, thence to an indicator of the steelyard type situated 16 ft from the centre line of the drum. The indicator is of the "Denison" patent equilibrium controlled ticket stamping type, insuring mistake-proof records by a combination of electrical and mechanical movements which prevent the operator from printing until the cover enclosing the steelyard is closed and until the poise-weights have been set correctly to the weight of the hopper and contents. The machine is capable of weighing 30 short tons at a time but the usual load is 28 tons. After obtaining the gross weight the drum is rotated and discharged into a receiving bin situated below it. The empty drum is weighed and the net weight re-

Jan 1, 1947

By C. S. Simons

Manufacturers of filtering, thickening or clarifying equipment, have been active in developing machines to meet increasingly rigid operator requirements, and the innovations resulting from this effort are moving into commercial applications. In general, the results of these applications are reported to be good. Little has been reported on progress in theory. The growing insistence on the part of pollution control agencies that waste water discharged into streams contain less and less suspended solids is being felt by a broad cross section of industry. A new clarifier, based on the often rediscovered fact that suspended solids settle more rapidly in inclined channels, is being marketed by Neptune MicroFLOC of Corvallis, Ore. This unit employs modules of inclined tubes, mounted in the upper zone of the clarifier, which carry the water flow. These were developed for light solids, such as those encountered in domestic water treatment and in paper mill waste water. In these applications, flow rates up to about three times those permissible in conventional clarifiers are reported to give comparable overflow turbidity. By combining these units with mixed media filters, high clarity may be obtained with minimum capital. Use of such units in the metallurgical industry, particularly where water reuse or effluent quality is important, should grow.

Jan 1, 1970

Many definitions have been advanced and many limitations advocated in the use of the terms, veins, lodes and ledges. The following definitions appear to follow the best usage. [ ] A fissure vein, according to Lindgren, is a mineral mass tabular in form as a whole, though often irregular in detail, filling or accompanying a fracture or series of closely set and intimately related parallel fractures in the enclosing rock, the mineral mass having been formed later than both the country rock and the

Jan 1, 1932

By Courtenay de Kalb

REVISION of the United States mining law is needed. chiefly because of the following reasons: 1. The conceptions as to the characteristics of orebodies that were held at the time the statute of 1872 was enacted have since proved to be in many respects erroneous. 2. The operation of the existing law has been found to work unnecessary hardship upon many claimants to mineral land. 3. The existing statute fails in large degree to encourage development of mineral resources. 4. The existing law often produces conflict between placer and lode-claim rights, working unnecessary injustice to placer claimants. 5. The methods of establishing the rights of locators on United States mineral land are defective, and are not uniform throughout the States within which such lands exist. LAW OF THE APEX The objections to the so-called "law of the apex" are so well known as to require no detailed statement. It is sufficient to point out that the apex rule was based upon the notion that ore deposits consisted of well-formed veins included between definite walls, like the slice of ham in a sandwich. The fact is that veins conforming to that simple type are rare. Irregularity is the rule, and the chief metal production of the United States comes from masses which bear no resemblance to the tabular form of vein. Manifestly the law of the apex fails completely in such cases. Moreover, the tendency is constantly toward the exploitation of ores of lower grade than could formerly be worked, and such deposits exist mainly in the form of large irregular impregnated zones and masses, so that the future. development of our mineral resources would be continuously embarrassed by shadowy claims to extra-lateral rights by the locators of so-called apexes

Jan 2, 1915

By E. A. Gulbransen, W. S. Wysong

THE behavior of tungsten and its surface oxides in oxidizing and reducing atmospheres and in high vacua at elevated temperatures is a question of considerable technical importance. The use of tungsten as a metal or as an important component in alloys in high temperature oxidizing atmospheres has been limited because of the unprotective nature of its oxide film and the volatility of its oxide. This paper will present results of a microbalance study1,2 of the following problems: (I) the oxidation behavior in the temperature range of 25 to 550°C (2) the reduction with pure hydrogen of thin oxide films formed on tungsten, and (3) the volatility of thin oxide films on tungsten. Tungsten is an interesting metal to study for the following reasons: (1) although the oxide to metal volume ratio is greater than one, the oxide is not considered protective, (2) the metal readily oxidizes at temperatures from 300° to 550°C (3) the oxides W02 and WO3 are reduced at temperatures as low as 500°C. by hydrogen, and (4) the oxide W02 is volatile at temperatures from 800 to 1100°C. LITERATURE The oxidation of tungsten in its thin film range has not been studied critically. In the thick film range Dunn3 has made the only systematic study. He found the oxidation rate to obey the parabolic rate law in the temperature range of 700 to 900°C. The temperature variation of the oxidation rate constant was found to follow an exponential law of the Arrhenius type. An inflection was noticed in the temperature plot of the rate law constant at 850 to 900°C. This was attributed to a phase change in the oxides. Scheil4 has studied the oxidation rate at 500 and 700°C over long periods of time and found a linear rate law. This result was interpreted as evidence for the presence of a nonprotective film. Pilling and Bedworth5 analyses of the oxide volume to metal volume ratio would indicate that a compact protective film should form. McAdam and Geil6 have studied the oxidation of tungsten in the thin film range using the interference color method. A parabolic rate law was found. Their curves showed that tungsten oxidizes faster than nickel but more slowly than iron. The lattice structures found in the oxidation of tungsten surfaces have been studied by Hickman and Gulbransen.7 They have reported that W03 is the stable oxide in contact with the metallic substrate up to approximately 600°C while W02 forms first at 700°C. Hägg and Magneli8 have recently reported a study of the lattice structures observed in the tungsten oxides using the X-ray diffraction method. In addition to an a-phase W03 and a d-phase W02, they reported the existence of two new phases. A ß' phase, homogeneous between

Jan 1, 1947

By Sidney Powers

CONTENTS PAGE Distribution of fields 4 History of development 6 Origin of oil 7 Structure,, accumulation and migration 8 Reservoir rocks 9 Methods of drilling and exploration to Oil-field statistics 12 Description by regions: United States: Appalachian region 12 East-central states 17 Kansas 18 Oklahoma 19 Texas 24 Arkansas 32 Louisiana 33 Mississippi -.. 34 Rocky Mountain region 34 California : 37 Canada 41 Mexico 43 Cuba 46 Bibliography 46 THE purpose of this brief account of the occurrence of petroleum in North America is to make available to those who have a knowledge of geology, but who are not engaged in the petroleum industry, a few salient facts about the location of oil and gas fields, their productivity, the important structural types of accumulation and the age of the rocks containing petroleum. A few useful data and statistics are furnished, yet not complete statistics that are available elsewhere. Geology has been treated in simple terms because the reader is presumed to have little interest in the names of formations and of oil sands. Mineral deposits are more or less analogous. Whether oil or metals, minerals are found in rocks, largely in sedimentary rocks which carry water or have at one time carried it. A genetic or accumula-

Jan 1, 1931

By Walter V. Knopp, Laurence Delisle

The aim of this work was the preparation of nickel-steels from elemental metal powders by powder metallurgy techniques. It was known that plain carbon steels could be made from a mixtufe of iron powder and graphite and that the effect of carbon on iron in powder form was of the same nature as that produced in fusion metallurgy. The problem in making nickel steels from elemental powders consisted therefore in finding out whether sufficient diffusion of the nickel and other incidental metals . normally present in such steels could be induced in the solid state to modify the properties of plain carbon steels made from powders and produce the beneficial effect of alloying. The composition selected originally was that of an S.A.E. 2330 steel. Metal powders, in the proportion correspending to that composition, were mixed with graphite, pressed, and heated at different temperatures for different periods of time, to produce bonding of the metal particles and mutual diffusion of the various elements without melting. Temperatures up to 1325°C and sintering periods as long as 6 hr were first investigated because it was expected.that such conditions would produce maximum diffusion with an accompanying improvement in the properties of the alloy. It was found that, although diffusion proceeded to a large extent under the conditions investigated, it would not be complete unless sintering were carried out at a high temperature for much longer than 6 hr. Relatively high temperatures and long sintering times are objectionable from a practical point of view, particularly when a low COSt material is to be produced, because they necessitate the use of special, costly equipment. Work could be done to improve the diffusion of iron and nickel by changing conditions other than the sintering temperature and time, that is, finer primary or alloy powders could be used. However, a marked change in the properties of the steel had been observed even with only partial diffusion. It was thought, therefore, that instead of trying to improve the diffusion, advantage might be taken of its incompleteness to produce a special structure consisting, in the unquenched condition, of a hard constituent, rich in nickel, dispersed in a tough pearlitic matrix. Steels with such a structure, not readily obtainable by fusion, should have desirable mechanical properties. Besides, it should be possible to prepare them from elemelltal powders under economical conditions. This latter alternative was therefore adopted for the second phase of this work. This report is divided into four parts: I. General Procedure. 2. Effect of Sintering Temperature. 3. Effect of Varying the Nickel Content. 4. Effect of Alloying Elements. General Procedure The general technique of cold pressing as used in powder metallurgy was applied.

Jan 1, 1949

By Harry K. Ihrig

The hot-working of iron and steel is an art dating back to antiquity, but until about 25 years ago, relatively few alloying elements were used, and these were present only in small percentages. With the exception of sulphur, the amounts of other elements in steels did not markedly affect their hot-workability. The references in the literature on the effect of other elements on the hot-workability of steel are usually reports of failure of these steels in forging or rolling.1-8 With the increased use of alloying elements, and their use in larger amounts, it was observed that many of the new steels were red short in certain critical ranges or at all hot-working temperatures. The stainless steels are particularly difficult to hot-work. The determining of the correct conditions for piercing, rolling and forging of these alloys by experimentation in the mill often results in large losses of these expensive metals. It also is found that the hot-workability limits of many types vary from heat to heat, and hence poor results are obtained on changing to a new heat after a previous one has rolled satisfactorily. To determine the effect on hot-workability of iron to which various elements have been added, it was necessary to devise a method that could be used on small quantities of metal. In such a method, the minimum number of variables should be present, and the procedure should be simple, quick and correlatable with large-scale hot-working operations. Sauveur,9 in the first Henry Marion Howe lecture in 1924, described the effect of carbon on the ductility of steels in torsion near their critical points. He found that carbon increases the plasticity of gamma iron. In the 1930 Campbell Memorial lecture,10 he gives the effect of carbon, chromium, and chromium and nickel on the ductility of steels under 2000°F. in torsion. Ellis11 has studied the malleability of steels at various elevated temperatures by means of a single-blow drop-hammer test. In this test the percentage decrease in height of standard cylinders is taken as a measure of their malleability. He has shown that in the low-alloy steels studied, carbon has a greater effect than nickel, chromium and vanadium. In 1938 the first tests were run on a new quantitative hot-workability test in the laboratories of the Globe Steel Tubes CO. Thum12 mentioned it in 1940. An illustration of the apparatus was published in January 1942.'' The effect of a few alloying elements on the hot-workability of metals was shown in a description of the test in 1944.14 Description of Test Method The method adopted after a trial of several others is a rapid twisting of bars to failure in a furnace. The standard-size bar was chosen as 9/16 in. It is prepared from larger pieces by forging and cold-

Jan 1, 1947

By Harry K. Ihrig

The hot-working of iron and steel is an art dating back to antiquity, but until about 25 years ago, relatively few alloying elements were used, and these were present only in small percentages. With the exception of sulphur, the amounts of other elements in steels did not markedly affect their hot-workability. The references in the literature on the effect of other elements on the hot-workability of steel are usually reports of failure of these steels in forging or rolling.1-8 With the increased use of alloying elements, and their use in larger amounts, it was observed that many of the new steels were red short in certain critical ranges or at all hot-working temperatures. The stainless steels are particularly difficult to hot-work. The determining of the correct conditions for piercing, rolling and forging of these alloys by experimentation in the mill often results in large losses of these expensive metals. It also is found that the hot-workability limits of many types vary from heat to heat, and hence poor results are obtained on changing to a new heat after a previous one has rolled satisfactorily. To determine the effect on hot-workability of iron to which various elements have been added, it was necessary to devise a method that could be used on small quantities of metal. In such a method, the minimum number of variables should be present, and the procedure should be simple, quick and correlatable with large-scale hot-working operations. Sauveur,9 in the first Henry Marion Howe lecture in 1924, described the effect of carbon on the ductility of steels in torsion near their critical points. He found that carbon increases the plasticity of gamma iron. In the 1930 Campbell Memorial lecture,10 he gives the effect of carbon, chromium, and chromium and nickel on the ductility of steels under 2000°F. in torsion. Ellis11 has studied the malleability of steels at various elevated temperatures by means of a single-blow drop-hammer test. In this test the percentage decrease in height of standard cylinders is taken as a measure of their malleability. He has shown that in the low-alloy steels studied, carbon has a greater effect than nickel, chromium and vanadium. In 1938 the first tests were run on a new quantitative hot-workability test in the laboratories of the Globe Steel Tubes CO. Thum12 mentioned it in 1940. An illustration of the apparatus was published in January 1942.'' The effect of a few alloying elements on the hot-workability of metals was shown in a description of the test in 1944.14 Description of Test Method The method adopted after a trial of several others is a rapid twisting of bars to failure in a furnace. The standard-size bar was chosen as 9/16 in. It is prepared from larger pieces by forging and cold-

Jan 1, 1947

By R. A. L. Black, J. E. Jennings

The problems of slope stability in open cast mines are examined. A criterion, the instantaneous stripping ratio, is suggested for use in the design of pit slopes and as an index of control at all stages of the exploitation of the orebody. This criterion may also be related to safety and to the maximizing of profits. Two approaches to safe design of slopes, one from the point of view of soil mechanics and the other from the point of view of rock mechanics, are described and critically compared. The effect on slope stability of the regional tectonic stress field is discussed. Explanation is given of the application of the Terzaghi effective stress concept to problems in both soil and rock environments, including possible effects when borehole deformation techniques are used to measure stresses in rock in situ. A company embarking on open cast mining is faced with two basic questions: 1) will the venture be profitable and 2) can it be carried out with safety? The two questions are obviously interrelated because both depend upon the slope angles adopted for the pit. The cost of open cast mining depends largely upon the stripping ratio, defined as the volume of overburden that must be removed to the volume of ore recovered. The steeper the slope angles, the more favorable the stripping ratio, but the stability of the slopes, and therefore the safety of men and materials in the pit, require that the angles be made relatively flat. Consequently, the design depends upon a compromise: the slopes must be steep enough to result in economical mining and flat enough to ensure safety. Today there is a world trend towards deeper mining by open cast methods. This is mainly due to the higher cost of underground mining and the lower cost of open excavation resulting from the introduction of large modern earth and rock-moving machinery. Deeper open cast mining has led to a very great increase in the volumes of wasted overburden, and much thought is being given to the considerable economic benefits which would result if pit slopes could be made steeper by even one or two degrees. The result has been an increasing interest in research into slope stability problems in the expectation that the application of scientific principles will provide solutions leading both to economies and to more predictable operation of the mines. In at least four places, the U.S., Australia, Western Germany and Southern Africa, comprehensive investigations are at present in progress, and it is the object of this paper to review some of the more important aspects of these programs. RELATION BETWEEN ECONOMY OF OPERATION AND SLOPE ANGLES The main object of any industrial enterprise in a free economy is to make a profit. In mining, where profits must be made from a wasting capital asset, a further definition of the profit motive is imposed, namely that the economic aim should be to maximize the total possible profit. But since profits deferred for a number of years are not as valuable as profits that are immediately available, it is usual to discount deferred profits at some rate of interest which reflects their current or present value in the hands of the investor. Thus, in mining the logical aim can be defined more closely still: to maximize the present value of the total future profits. In commercial terms the present value represents the market value of the operation as a going concern. Many factors enter into the forecast of current and future profits. They include the volume of production, the price of the salable product and the cost of production. Current profits can be estimated with reasonable accuracy by the operating engineers; but it is the task of economists and management to assess future trends in the mineral markets and in the economy as a whole, and together with the engineers, they can then estimate the future cost and profitability of the mining operations. In open cast mining, the rate of ore production once decided on remains a virtually constant factor unless a major change in the capital structure of the mine is made. But one factor over which the operator has a considerable measure of control is the ratio of the volume of ore mined to the volume of waste over-

Jan 1, 1963

By C. M. Schwartz, A. E. Austin, W. B. Wilson

High-temperature X-ray diffraction studies were conducted with Th-U alloys with up to 10 wt pet U. The solid solubility of uranium in thorium as a function of temperature was determined by the method of lattice parameters. Thorium will dissolve up to 2.5 wt pet U at 950°, 4.5 wt pet U at 1150°, and 7.5 wt pet U at 1250°C. Determinations were made of the temperature of the transition of thorium and of the effect of uranium upon the transition. The a to ß transition for thorium was observed to occur at 1330' ±20°C. Mean coefficients of expansion were calculated for thorium and two alloys, and for ThO2 in contact with the thorium, using X-ray lattice-parameter data. Values obtained at 950° C for thorium and Tho2 were 12.1 and 9.40 X 10-6 per OC, respectively. Impurities obtained during the X-ray exposure were identified by diffraction and were essentially Tho2 and ThC, with two additional unknown phases being detected. The effect of the impurities upon the results is discussed. DIRECT investigation (i.e., high-temperature X-ray diffraction studies) of the phase diagram of thorium-rich uranium alloys has been shown to be necessary since recent work1 - has disclosed the presence of an allotropic transformation near 1400°C in pure thorium with the room temperature face-centered-cubic phase transforming to a body-cen-tered-cubic structure at the elevated temperature. The effect upon the transition of the addition of uranium to thorium and of the solubility of uranium in thorium at high temperatures remained unknown, yet was of interest in understanding fabrication procedures and elevated temperature use. The present work was undertaken to provide information in this area by determining the transition temperature, the effect of uranium on the transition temperature, and the solubility of uranium in thorium as a function of temperature. Experimental Work The high-temperature diffraction data were obtained using a camera especially designed for the purpose3 and capable of reaching temperatures in excess of 2000°C at pressures as low as 1 x 10." mm Hg. Temperature regulation was provided by regulating the power input to ±0.1 pet variation, and by regulating the water flow through the camera jacket to provide a constant thermal load. The X-ray sample was a rod nominally 80 mil diam, which was further turned down to 20 mil and then etched to 18 mil over 1/2 in. of one end. This was placed in the sample holder and mounted on the camera so that the smaller part was surrounded by a cylindrical tantalum-sheet radiation-type heating element. Diffraction from the sample was recorded on film after passing through a slot in the heating element and radiation-baffle shield and through beryllium vacuum windows. The X-ray film mounting was of the Straumanis type4 with a camera diameter of 114.59 mm. Since previous work of Chiotti' indicated that impurities considerably alter the transition temperature, chemical analysis of the arc melted iodide crystal-bar thorium samples was obtained prior to testing. The analysis disclosed the material to contain as low as 0.001 ±0,0002 wt pet H and 0.007 ±0.001 wt pet 0. Carbon was 0.003 wt pet and nitrogen less than 0.002 wt pet. This material was sealed in mild steel in an inert atmosphere and subsequently hot rolled to 3/8-in. diam rods at a temperature of 732°C. Following removal of the jacket, the material was pickled and cold swaged to 1/8-in. rods, from which the diffraction samples were prepared. The alloys were similarly prepared, with the uranium being added during arc melting. The uranium analyses of the alloys prepared appear in Table I. The experimental procedure for diffraction examination of the three samples of high-purity thorium differed from those of the Th-U alloys. The original practice, later modified, consisted of pumping down the camera with the diffusion pump on and then admitting liquid nitrogen to the cold trap of the system. This was modified for the Th-U alloys by maintaining liquid nitrogen in the cold trap at all times before and while the diffusion pump was heated. This minor change produced a reduction in the amount of carbon pickup by the sample during exposure to the diffusion-pump vapors. The sample was brought to the desired test temperature and exposed for 21/2 hr at pressures which were usually 2 x 10-6 mm Hg, or lower. Exposures were made at

Jan 1, 1959

By P. W. Neurath

IN recent years the domain theory of ferromag-netism has been put on a sound experimental and theoretical basis. But its application to one of the most widely used high quality magnetic materials, the cold-rolled grain-oriented 3 pct Si-Fe used in transformer cores, has been rather difficult because of the complexity of the domain structure of the poly crystalline sheet material. This paper presents some experimental data for this material, showing the relation between plastic and elastic stresses, 60-cycle watt losses, and the domain structure as observed visually. Only a very tentative qualitative explanation of the effects will be attempted. Some initial results were reported earlier.'

Jan 1, 1957

By K. J. Powers

The Mine Accident, Injury, Illness and Employment Database at the Mine Safety and Health Administration's Health and Safety Analysis Center is a computerized system that stores accident, injury, illness and employment data about all coal and metal/nonmetal mines in the United States. The paper discusses the system for collecting, storing, analyzing, and reporting this information and how these data are used in the ongoing effort to increase the health and safety in this nation's mines.

Jan 1, 1983

By A. R. Kaufman, P. Gordon

THE large-scale manufacture and use of uranium in conjunction with the atomic energy development during the war led to a need for knowing the equilibrium diagrams of uranium with various other metals. The alloys of uranium with aluminum and with iron were among the first that were studied for this purpose. Much of the work was done in the manner of a survey since it was necessary to determine the important features of the phase diagrams rather than to obtain completely detailed results. For this reason no attempt was made to locate exactly such features as liquidus lines, solid solubility limits and compound and eutectic compositions. It is believed, however, that there are no great inaccuracies in the diagrams reported here and that no important points were overlooked. Earlier work on alloys of uranium with aluminum and iron is almost nonexistent and in each case is considered to have been of little value by M. Hansen. It is interesting to note, however, that the compound UAl3 was first reported in 1902 by L. Guillet. Experimental Procedure Materials: The uranium used for making most of the aluminum alloys was obtained from material prepared by Metal Hydrides, Inc., and melted in vacuum at M.I.T. Because of the lack of an adequate supply of metal, it was necessary to use material from several different batches and hence it is impossible to state an exact analysis. However, a few results indicated about 0.01 to 0.03 pct iron and probably about 0.03 to 0.05 pct carbon. Toward the end of the work a small amount of metal was obtained from Brown University and from Iowa State College and this was used in determining the transformations in pure metal and in some dilute alloys. All of the aluminum used in this investigation came from a supply of high purity metal (greater than 99.9 pct aluminum) which was obtained through the courtesy of Dr. Mehl of the Carnegie Institute of Technology. The uranium used for making the alloys with iron was produced by the bomb reduction process which has been described by J. Chipman.² This metal, after vacuum melting, contained about 99.9 pct uranium by weight with carbon and iron as the chief impurities. Electrolytic iron containing about 0.012 pct carbon, 0.020 pct nickel and 0.009 pct copper was used in making the melts. Melting Equipment: The melting of the alloys went through a stage of development which culminated in the use of beryllia or beryllia-lined crucibles and in the use of high frequency heating in either vacuum or in an atmosphere of argon. It was found that uranium at a few hundred degrees above its melting point would pick up aluminum and to a lesser extent silicon from an alundum thimble while aluminum above 1000°C would extract silicon from the impure alundum. No reaction of either metal with beryllia was noted at temperatures as high as 1800°C. The distillation of aluminum from the aluminum-rich alloys was quite troublesome at temperatures above about 1300°C and was only partially avoided by the use of argon instead of vacuum. Melting in resistance furnaces,

Jan 1, 1951

By J. B. Morrow

WITH numerous plans under consideration for coal classification, and with the advent of the Bituminous Coal Code, the intelligent sam-pling of coal has become increasingly important. To us it is rather significant that there have been very few fundamental studies of coal sampling in American technical literature since those of E. G. Bailey, which appeared in the Journal of Industrial and Engineering Chemistry in March, 1909. He covered the subject up to that time so thoroughly and in such an excellent manner that perhaps many other later students have felt that they could add very little to his findings. The recent studies of the British Engineering Standards Association have indicated the possibility of a somewhat different interpretation of Bailey's results, permitting the taking of smaller samples, and perhaps it will now be helpful to reopen this question. C. W. H. Holmes, in an informative series of articles on coal sampling recently published in Colliery Engineering, makes two rather interesting statements, as follows: It is scarcely surprising to find a lack of interest and knowledge regarding the sampling of coal not only in the mining industry itself but also among consumers of industrial fuel: at its best coal sampling is a dirty business, regarded as a nuisance and an expense by the commercial man, and usually as a nuisance and nothing else by the chemist. The writer can conceive only two classes of people who have never experienced any difficulty in obtaining representative samples of coal from wagons; those who have never tried to, and those who have never had the necessity or desire to check the accuracy of their work. The primary purpose of this paper is to present some tabulated data of the more significant results of a sampling investigation undertaken during the last four years to obtain certain fundamental data on the variables connected with coal sampling and to point out that often assumptions have been made that are not in accordance with the facts. One of the standard sampling methods states:

Jan 1, 1935

By W. L. Saunders

It is now generally admitted by experts that at least so far as rapid progress is concerned the Alpine system of tunnel-driving is superior to any other. This is perhaps natural in view of the record of experience in driving tunnels through the Alps. These great mountain-chains cannot be treated in the ordinary way by shaft-sinking and driving headings, thus multiplying the points of attack. The work must be done from the ends only, hence speed in driving is of the utmost importance ; and, as necessity is the mother of invention, the concentration of effort to make progress has resulted in an organization and in mechanical appliances that have produced results so much in excess of the usual practice, even in America, that a discussion of the subject in detail should be of much value to the engineer and contractor. The first Alpine tunnel mas the Mont Cenis, length 7.5 miles, driven with a progress that averaged about 7.75 ft. per day. Next came the Saint Gothard, 9.5 niiles long, 18 ft. per day; Arlberg, 6.5 miles long, 27.25 ft. per day; Simplon, 12.25 miles long, 36 ft. per day. The figures represent progress when driving from two headings, so that by dividing them in two we get the daily single-heading progress. The latest of the Alpine tunnels is the Loetschberg, now being driven. In this work the world's record has been beaten by a single day's record in one heading of 36 ft. and by an average daily record in one heading of 29.5 feet. The Alpine range forms a natural barrier between a large section of northern and southern Europe. This range extends from the southeast of Prance to the frontier of Hungary, betveen Italy and the plains of sonthern Germany. The contour

Jan 1, 1912

By J. B. Newsom

SAFER, cheaper, and faster sinking of mine openings seems to have been realized with the completion of a borehole 5 ½ ft. in diameter and 1208 ft. deep, in Minnesota, during 1938. Moreover, as the opening is to be used solely for ventilation, its circular cross section, smooth walls and freedom from fire hazard recommend it in comparison with the usual timbered shafts of rectilinear cross section. It should be pointed out that a drill hole sunk without the use of explosives frequently will stand open without support, whereas a shaft sunk by standard procedure using dynamite usually must be timbered because of the wall-shattering effect of explosives. The saving in maintenance resulting from the elimination of timber is obvious. The work was done by Pickands Mather & Co. at its Zenith mine, Ely, Minn. This company wanted a ventilation opening capable of delivering 50,000 cu. ft. of air per minute to the fourteenth level, 1200 ft. below the surface. While several general articles1-3 have described the method used, detailed time and performance records have not been presented before. Moreover, with a method as new as this, it is important to compare the results attained under widely varying conditions. Among the new conditions faced at Ely were some extremely hard rock, a series of vertical fractures, seepage water, and some long stretches of sound rock which, combined with excellent equipment, gave a chance to operate without unusual delays. Developments in boring large holes have generally taken the obvious course of increasing the size of the equipment, a line of attack that has resulted in putting down 3-ft. diameter holes at damsites for studying the foundations4 and in drilling ventilation openings between levels at Butte. 5 Such drills operate from the collar of the hole, and the power from the drill is transmitted to the cutting tool through drill rods or pipes. In order to keep down the volume of rock that must be ground to sludge, the cores in large-diameter drilling are made as large in diameter as possible. Their large diameter increases their weight per foot of length, which

Jan 1, 1939