Search Documents

By J. B. Dyess

TARNISH films on some of the common metals (particularly on copper and silver) have been of much scientific and commercial concern for a long time, but before the development of the electrical method1 of measuring film thicknesses there was no satisfactory quantitative approach by which to study the separate parts of these complex films. This method has been adapted to the measurement of duplex (cuprous-cupric) oxide films on copper .2 In the present work it has been used to measure tarnish films on copper when they were mixtures of cuprous oxide and cuprous sulphide, and also when they contained cuprous oxide, cupric oxide and cuprous sulphide, each component part being measured at a different potential value. Oxide-coated copper specimens, prepared by heating copper in air at chosen temperatures for given periods, were exposed to moist hydrogen. sulphide in air to form the various oxide-sulphide films studied. The comparative resistances afforded by (1) different thicknesses of oxide films, and also (2) equal thicknesses of oxide and sulphide films, against severe attacks of hydrogen sulphide were measured. The electrical method requires that the time be observed for the cathodic reduction of each part of the film substance, and these respective time values multiplied by the constant current give the corresponding quantities of electricity expended. Then each millicoulomb per square centimeter represents a film thickness of T= MX10 8 2D X 96,494 X 103 (a) where M is weight of oxide (or sulphide) giving one gram-atom of oxygen (or sulphur) for cathodic reduction, D is density of the oxide (or sulphide) and t is the thickness in Angström units per millicoulomb per square centimeter. The value of t for cuprous sulphide (cubical) is 14.27, and is obtained by substituting 5.78 for D and 159.20 for M in equation a. Previous values2 of t for cuprous and cupric oxides (12.36 and 6.39, respectively) were used in the present work.

Jan 1, 1939

By L. A. Price

With increased stripping ratios and with dwindling ore content, the mining fraternity is increasingly turning to larger and larger equipment for profitable open pit operations. The availability of higher horsepower prime movers and increased-capacity electric transmissions using either wheel-mounted or axle-mounted traction motors makes a reality of single-axle, rear dump trucks having 150 to 250 ton capacity. The size of electric loading shovels is inherently geared to the size of haulage equipment. To work effectively with this new generation of trucks, the Harnischfeger Corporation has introduced its P&H Model 2800 with a capacity of 20 to 25 cu yd and a working weight of nearly 1,500,000 lb. The Model 2800, depicted in Figure 1 loading a 200 ton truck, has many new electric and mechanical features designed to give excellent production and low cost operation. Chief among the new features is the ELECTROTORQUE control system. Electrotorque is a completely static, solid state electronic system supplying controlled power both to the armatures and to the fields of the d-c shovel drive motors. It eliminates many major electrical rotating machines and their attendant maintenance. The system was developed jointly by ASEA of Sweden and Harnischfeger Corp.

Jan 1, 1970

By B. D. Lichter

In a previous paper, Oelsen, Schuermann, and Hey-nertl pointed out the possibility of obtaining complete thermodynamic functions for alloy systems from calorimetric measurements alone. Specifically, if the heat content of a heterogeneous, multicomponent system is known as a function of temperature and composition, then it is possible to derive the heats, entropies, and free energies of formation of liquid phases and of solid intermediate phases of fixed composition. The authors present equations and graphical techniques applicable to eutectic systems and systems with intermediate phases without solid solubility at lower temperatures. eijering has considered possible extension of the treatment to systems with complete solid-state miscibility at lower temperatures; however, experimental difficulties practically restrict the method to systems with very limited miscibility in the solid state. The purpose of this note is to present an alternative derivation of the heats and entropies of formation of liquid phases and of solid intermediate phases from heat-content measurements alone. Fig. 1 shows three types of phase diagram to which the analysis may be applied. If the heat content is determined as a function of composition x, at temperature T, we have quite generally and the heat of mixing of the liquid is obtained directly from heat-content measurements. If the temperature T lies in a two-phase region (solid-liquid) then

Jan 1, 1967

By Sherwin F. Kelly

Twenty five years of exploration has shown that the "geophysical dollar" is worth $1780 in the Orange Free State, $1488 on the Witwatersrand, $85 in Sweden, $28,000 in the Transvaal and $3500 or more in the U.S.

Jan 6, 1951

By Ling Yang, John Henderson

Self-diffusion coefficients of copper in molten copper have been measured by the capillary reservoir method in the temperature range 1140o to 1260°C. The results can be represented by the equation D = [(1.46 * 0.01) x 10-3) exp [(-9710 * 710)/RT] cm2/sec. The energy of activation agrees within the limit of experimental uncertainty with that for viscous flow. The relationship between the diffusivity and coefficient of viscosity is best described by the equation D = kT/4pnr cm2/sec. MEASUREMENT was made of the self-diffusion coefficient of copper in molten copper in the temperature range 1413º to 1533ºK, using the capillary reservoir technique and CU64 as the radioactive tracer.The procedures for filling the capillaries, making the diffusion run and evaluating Dcu from the counting results were the same as described previously.1,2 All experimental operations involving the melt were carried out in a purified argon atmosphere. A graphite crucible, enclosed in a McDanel tube, was used as a container for the melt because of its satisfactory nature as a refractory material and the low solubility of carbon in copper. Graphite was also used for the capillary material. A McDanel thermocouple sheath, to which graphite radiation shields were affixed, was used to hold the capillaries. By moving this sheath through a rubber seal at the top of the McDanel tube, the capillaries could be lowered into or raised out of the melt. A Globar furnace with a constant temperature zone (± 2°C) of 2 in. was used to heat the assembly. The temperature of the furnace was the equilibrium value corresponding to a given setting of the transformer. Temperature was measured with a Pt-10 pct Rh/Pt thermocouple and varied during a run

Jan 1, 1962

By M. J. Mullikin, J. B. Conway

Equations capable of representing combined first -and second-stage creep behavior include the Andrade, Cottrell-Aytekin, Garofalo, and de Lacombe equations along with a third-degree polynomial in t1/3. Employing some recent high- temperature creep data for arc-cast tungsten the effectiveness of these expressions was evaluated. It was found that, in this instance, the most accurate representations were afforded by the third-degree polynomial in t1/3 and the de Lacombe equation. Also noted was the fact that the Andrade equation gave results just slightly inferior to those obtained with the third-degree polynomial, definitely better than those due to the Cottrell-Aytekin equation, and slightly superior to those furnished by the Garofalo equation. EXPRESSIONS designed to describe combined first -and second-stage creep behavior must possess certain specific characteristics. At time zero the equation must reduce to a strain value corresponding to the instantaneous deformation on loading. Then in the early moments following load application transient-creep behavior must be described to reflect a creep rate which constantly decreases with time. And finally at larger time values linear (or at least nearly linear) strain-time behavior must be accounted for to yield the steady state or minimum creep rate. Some equations, such as the one based on the parabolic creep law, yield fairly satisfactory results in transient analyses but are not effective at all when combined first- and second-stage data are to be analyzed. Other equations give equally accurate results in both instances although in general the complexity of the equation is slightly increased. For example the Andrade1 equation: has found fairly general application in expressing first-stage creep behavior. Furthermore the contribution of the exponential term becomes more and more prominent as the time increases and causes this equation to exhibit a point of inflection at large values of time. With a proper selection of equation constants the curve can be made fairly flat in the region of the inflection point indicating a desirable equation form for combined first- and second-stage creep analysis. Another equation form with the proper characteristic is that of Cottrell and Aytekin:2 e =a +bt1/3 +ct [2] Obviously as time increases the first derivative of this expression approaches a constant value to suggest application to combined first- and second-stage creep analysis. Similarly a third-degree polynomial in t1/3: e -a + bt1/3 + ct2/3 +dt [3] has the same characteristics. Expressions of this type have been shown3 to be very effective in the analysis of transient-creep behavior and the fact that the first derivative has the same characteristic as Eq. [2] suggests use in the combined analysis.

Jan 1, 1967

By M. Cross

INTRODUCTION The results of the Japanese dissective investigations have [l-4] transformed our understanding of how the blast furnace operates. These studies revealed an internal structure of the furnace burden with five main zones, as illustrated in Figure 1. In the granular zone the charged material retains its structure whereas in the cohesive zone the iron ore particles are at advanced stages of reduction and form a semi-molten mass with a relatively high flow resistance. In the active coke zone molten iron and slag flow through a matrix of loosely packed coke. The raceway is a relatively small void space generated by displacement of coke due to the hot blast momentum, whilst the hearth is packed with coke, slag and molten iron. [ ] It is now well appreciated that furnace control is largely achieved and maintained by using the burden charge distribution to determine the gas glow distribution within the furnace and, hence, the shape and extent of the cohesive zone. In fact, Wakayama et a1 [5] of Nippon Steel Corporation state that optimum furnace operation is synonomous with the formation of a desirable cohesive zone shape, which in turn is almost solely determined by the burden charge distribution and its mechanical properties [6]. Much of the development work on operating furnaces since the dissective investigations has been oriented towards the identification of external furnace measures which reliably predict the shape of the cohesive zone. Currently the most popular measures are top gas temperature, velocity and CO/CO, ratio profiles [5]. More recently pressure distributions as evaluated from a series of wall measurements down the height of the furnace are also being utilised [7] to identify the position and shape of the cohesive zone. A great deal of emphasis has been placed upon achieving a consistent quality in the burden charge materials, establishing a suitable set of operating conditions and only making changes when forced to, ie., the operation for some reason moves outside a desired operating range or the production requirements change. Operational control schemes based upon this philosophy (eg., Kawasaki's GO-STOP system [8]) have been remarkably successful at achieving both high production rates and relatively low fuel costs. Mathematical models have long been used as tools to assist in the analysis of the blast furnace process. Although, the models have been useful in post-operative analysis and for identifying trends, etc., they have not proved reliable for detailed design criteria or as the basis for effective control schemes. Such mathematical models have moved from simple statistical correlation, through overall and stagewise heat-and-mass balance calcu-

Jan 1, 1984

By K. S. Seljesater

SINCE the development of dispersion-hardenable lead-antimony alloys1 in the laboratories of the Western Electric Co., Inc., studies have been made of the effect of various third constituents on these alloys.2 This paper covers a study of the effect of small amounts of arsenic. This element is important since it occurs as an impurity in many commercial antimonial leads and the results obtained are particularly interesting as indicating a class of addition agents which exert a stabilizing effect on dispersion-hardened alloys. EXPERIMENTAL In order to-study the effect ,of increasing amounts of arsenic, a series of alloys were made up containing 1 per cent. antimony, and arsenic varying from 0. to 0.10 per cent., the balance Doe Run lead (99.997 per FIG. 1..-CHANGE OF MICRO-BRINELL HARDNESS WITH TIME OF 1 PER CENT. LEAD-ANTIMONY ALLOY. cent. lead). The alloys were cast into bars 1 ½ in. wide by ¾ in. thick and cold-rolled to about 1/8 in. thickness. Three samples of each composition were annealed 1 hr. at 225° C. and quenched in water. One set was aged at room temperature, one at 50° C., and the third at 100° C., the

Jan 1, 1929

In any earth-moving operation, more profit may be earned or lost by equipment scheduling than by any other single facet of the project. Many now-defunct earth movers would have survived the cost-profit squeeze had they followed an efficient, cost saving, equipment scheduling program. The ideal program would have every item of the equipment fleet working all of the time. In practice this ideal situation is not possible. Several basic methods of equipment scheduling, with an infinite number of minor variations, are used. The first approach is the use of a "minimum equipment fleet," of which all items or equipment are scheduled each working shift.

Jan 10, 1967

By Kenneth F. Whinery, John M. Campbell

Basically, the Buckley-Leverett theory involves two systems which are similar in nature but are differentiated by time. These systems may be described by the fractional flow and frontal advance equations which essentially characterize the mechanics of oil movement while being expelled from the reservoir. The fractional flow equation originally developed by Leverettl may be expressed in the more usable form The development of this equation is based on Darcy's law describing fluid flow through porous media and applies to the flow at only one point (it is a point function). For simplification, the fractional flow equation is written in the above form because the capillary forces always increase the fractional flow of the displacing phase regardless of the direction of flow or the displacing phase. If, for simplicity, the effects due to gravity and capillary pressure differences are neglected, the fraction of the displacing fluid, f, at any point in the flowing stream is related to the properties of the system by 1 Thus, it is seen that in the absence of capillary and gravitational effects, fd for a given sand and fluids varies only with saturation and pressure. The magnitude of the viscosity ratio, —a has an effective range (range of about 30) in the system where gas is displacing oil and a much smaller range for water displacing oil. In order to make the fractional flow equation more versatile, it is necessary to connect the fractional flow at a given point and saturation with time. This problem was approached by Buckley and Leverett" who developed the frontal advance equation, Eq. 3 states that the rate of advance of a plane that has a fixed saturation, Sd, is proportional to the change in composition of the flow stream caused by a small change in the saturation of the displacing fluid. It is, essentially, a transformation of a material balance equation representing the net rate of accumulation of the displacing phase within a homogeneous sand block. This accumulation is proportional to the difference between the rate at which the displacing fluid enters the sand and that at which it leaves. Eq. 3 describes the velocity with which a plane of constant displacing phase saturation advances through a porous system. Buckley and Leverett," Babson,' Kern," Welge, and others have adequately discussed the basic mechanism and application of the fractional flow and frontal advance equations. APPLICATIONS OF THE FRONTAL ADVANCE THEORY TO PETROLEUM RECOVERY Two general applications of the Buckley-Leverett frontal advance theory involve the system in which the oil is being displaced by an expanding gas cap overlying the oil zone and that in which the oil is being displaced by water. Displacement by Gas in the Presence of an Immobile Water Saturation A system in which gas is the displacing phase may be thought of as having two forces effecting the displacement process. These forces are the gravitational force and that force exerted by the displacing gas. The gravitational effects control the displacing efficiency of the gas. The gravitational effect will be less at higher rates of flow, thereby reducing the effectiveness of the displacement of the oil by the gas. The more efficient displacements occur at flow rates which are less than the gravity free fall rate. Capillary forces can be neglected without materially changing the magnitude of the gas saturation. The Mile Six pool is used herein to illustrate the calculating procedures in evaluating gas drive-gravity drainage field perfomlance. These calculations represent the determination of the gas-oil contact when the distribution of the hydrocarbon pore volume is considered. Two methods

By J. B. Clark

In 1933, R. paris1 published a phase diagram for the entire Mg-Ca-Zn system. He reported the existence of a ternary intermetallic phase, Mg5Zn5Ca2, which formed a quasi-binary with the magnesium solid solution. Since then, no extensive work has been reported on the system. Recently however, indications of the existence of a second ternary in-termetallic phase in equilibrium with the magnesium solid solution led to a reinvestigation of the solid phase equilibria involving the magnesium solid solution. The 335°C (635°F) isothermal section was chosen for study. Metallography and powder X-ray diffraction were selected as the best mutually corroborating methods for determining the solid phase constitution. Seventy-six alloys were prepared from singly sublimed (99.95 pct) magnesium, electrolytic (99.95 pct) zinc and USP calcium. The analyses of some of the alloys are shown in Fig. 1. The alloys were melted in a graphite crucible under a chloride flu and chill cast in a split graphite mold. Dif-fusion couples (see Fig. 2) were prepared by casting molten Mg-20 wt pct Zn alloy around a cylinder of Mg-30 wt pct Ca alloy. The alloy samples and the diffusion couples were sealed under argon in Pyrex vials and annealed in a furnace capable of controlling within 1/2°C of 335°C. At the conclusion of the anneal, the alloy samples were quenched in ice water and the diffusion couples were air cooled. Procedures standard for magnesium alloys were used for metallographic examination. Powder X-ray diffraction patterns were taken on a G. E. camera with a 14.32 cm dim using nickel-filtered copper radiation. The redetermined 335°C (635°) section of the Mg-Ca-Zn phase diagram is shown in Fig. 1. TWO ternary intermetallic phases, designated w and

Jan 1, 1962

By D. G. Westlake

Levine has concluded that prismatic slip in titanium is controlled by two distinct thermally activated processes in the temperature ranges O° to 220°K and 220" to 300°K. We feel that his evidence is not convincing. He has drawn a curve through the plot of activation volume u* vs temperature T with a break at 22WK, Fig. 2. We believe that considering the possible experimental error apd the fact that there are only four points between 4° and 196°K, one could be justified to represent these points by the smooth curve we show as a solid line in Fig. 12. Levine believes that (8rf/aT)+ is discontinuous at 220°K, but he hints that he recognizes the possible doubt. We doubt seriously that the results shown in Fig. 1 indicate a discontinuity at 220°K. Certainly if he were justified in drawing a straight line through only four points on Fig. 2, we are even more justified in drawing straight lines through the seven points between 77" and 297°K on Figs. 1 and 3, because a straight line touches all seven of his circles. If his measurements of t were so precise that his decision to draw two curves in Fig. 3 is valid, then the experimental technique is deserving of further mention. We have drawn a smooth curve through the results in Fig. 3 and used this and the curve in Fig. 12 to obtain the values of shown in Fig. 13. Finding continuous is a contradiction of Fig. 4, which deserves comment itself. Levine obtained the solid circles in Fig. 4 using Fig. 2 and a smooth curve through the points shown in Fig. 3. We have replotted these solid circles in Fig. 14. We submit that there is no basis for his two straight lines (dashed in Fig. 14), and therefore have superimposed the curve that we believe is indicated. Certainly, there is reasonable doubt that a discontinuity in dH/dT exists at 220°K, even when one accepts Fig, 2. Furthermore, if one draws the straight lines indicated by least-squares treatments of the results presented as open circles in Fig. 4, their intersection is at about 196°K, not at 220°K as shown. Thus the alleged agreement between Figs. 3 and 4 with respect to "break" temperatures is not apparent. In Fig. 9, Levine has drawn a straight line very much different from the one indicated by a least-squares treatment. Obviously, he has done this because he recognized that H = 0 when T = 0. He is consistent in drawing the low-temperature curves in

Jan 1, 1968

By Jesus P. Manzano

The report of which this paper is a summary was made in 1890 for the Compania Investigadora Mexicana y Americana. Since the region examined covers 900 sq. kilom., chiefly of wooded arid rocky hills, almost without roads, and for the most part uninhabited, While the examination had to be made in two months, of which period more than 15 days were continuously rainy, I need not say that this account is not complete and thorough. I. Geography and Topography. The center of this zone, 19 kilom. SW. of San Luis Potosi, is situated in lat. 21° 24' N., and long. 2° 3' W. of Mexico City. The altitude ranges from 1866 m. (that of San Luis) to . 2816 m. (that of the Realito mountain), in the Sierra de Sail Luis. The topography is hilly—partly wooded, partly bare. The principal more level areas are the Bledos valley on the south, and portions of the haciendas of Tepetates, San Fran cisco and Santiago, on the west. The water-supply is scanty. The two streams that cross the Zone, the Santiago and Bledos rivers, carry water nearly the year through, though much reduced in the dry season. Other streams are torrents of less importance. All the waters of the valley and Sierra of Sail Luis arc absorbed or sink, not passing beyond Soledad de los Ranchos. The Continental di vide is within the Zone, some waters going west to the Pacific, others east to the Gulf of Mexico. II. Geology. Concerning the geology of this district I condense the fol lowing from the memoir, Las Minas de Guanajuato, prepared for the Minister of Fomento by Senor Pedro Lopez Monroy, mining engineer, with which I am entirely in accord. He says, ill substance:

Jan 1, 1902

By Ivan Simon, R. K. McConnell

Anticipating the availability of tiltmeters suitable for use in boreholes, this article proposes a method of using one or more of these meters to determine in situ stress distribution before and after mining operations. Several ways of using relief techniques to measure in situ stresses in rocks have been developed. These techniques, summarized by Merrill,1 involve measuring deformations which take place when a specimen of rock is wholly or partially isolated from the stress field in the surrounding rock. Measurements of rock deformation caused by stress relief from mining operations can, in principle, also be used to estimate in situ stress distributions. Müller2 has mentioned experiments being carried on in Austria with a "deformation indicator" to determine the tilting of holes drilled before a mine opening is made. Similar work using borehole extensometers has been reported by Potts? and Duvall4 has called attention to the possible use of tiltmeters in making these measurements. Considerable attention is now being paid to the use of tiltmeters in detecting rock deformation associated with fault movements, earthquakes, earth tides, etc. The instruments used for these measurements have usually been of the mercury tube, water tube, or quartz fiber type, but because of their large size, and/or fragile nature, such instruments would not be suitable for use in mining stress measurements. Recent instrumentation developments, however, give promise that rugged, sensitive tiltmeters small enough for use in boreholes may soon be available.' In anticipation of these developments, this article presents a number of calculations of the possibility of using one or more tiltmeters emplaced in a drill hole prior to mining operations to determine the in situ stress distribution both before and after a mining operation. Consider point p (x, z) near a tunnel of radius a

Jan 1, 1969

By E. P. Abrahamson II

The effect of transition elements which form binary solid solution upon the recrystallization temperature of zirconium has been investigated. All additions raised the recrystallization temperature. A correlation is obtained between the logarithm of the rate of change of recrystallization temperature with atomic percent solute and the free atom ground state electron configuration of the solute element. ThE work of Abrahamson, et al., on dilute binary solid-solution alloys indicated a correlation between the free-atom ground state electron configuration of the solute and either the brittle-ductile transition or recrystallization temperature. These studies were carried out on bcc base materials. The implication is that the outer s and d electrons of the solute are the prime determinant of the absolute rate of change of recrystallization or transition temperature. Furthermore, the limit of linearity has been shown to be a function of solute electron configuration for recrystallization in iron and vanadium. To date no Complete systematic recrystallization study of dilute binary zirconium base alloys has been made. It is the purpose of this study to note whether the change in solvent structure from bcc to hcp will influence the correlation. It was also desired to learn more of the role of the electron configuration of the solvent on recrystallization temperature. PROCEDURE All alloys were made using 99.87 pct Zr with 0.01 Cr, 0.04 Fe, 0.006 Hf, 0.003 Mg, 0.003 Mn, 0.003 N, and 0.080 0 (132 BHN). The solute elements were 99.9 pct pure. According to the published binary phase diagrams6 and metallographic examinations at X750, all alloys used were solid solutions. The alloys were arc melted and remelted six times in the form of cubic 200-g buttons under an argon atmosphere. They were then hot pressed at 950°C to 0.450 in., upset pressed to 0.350 in., and annealed at 800°C for 1 hr. The specimens were then Blanchard ground to 0.250 in., removing 0.050 in. from each side. The grain size of the material at this stage was found to be 8000 100 grains per sq mm. The specimens were then cold rolled to 0.130 in. and cold pressed to 0.125 in., yielding 50 1 pct cold work. All alloys were then chemically analyzed for the principal addition. The interstitial contents remained at the values of the starting material when checked on random alloy specimens. The rolled sheet was cut into 6.75 by 0.25-in. lengths and heat treated in a gradient furnace for 1 hr. The gradient was 250o to 900°C over the 6-in. length, recorded continuously by six thermocouples resting on each specimen. Control was 3oC, accomplished at the hot end. The recrystallization temperature was determined metallographically using polarized light. The criterion chosen was the point on the specimen showing the first recrystallized grain at a constant magnification, X200. Specimens were repeated, and the agreement was found to be 3°C. RESULTS Three different pure zirconium specimens were tested, and the recrystallization temperature was

Jan 1, 1962

A New Ingersoll-Rand Turbo Blower The Ingersoll-Rand Co. has added to its Turbo Compressors and Blowers a low-pressure machine t o handle volumes from 3,000 to 35,000 cu. ft. per minute at from 1-2 ½ lb. These are particularly adapted to such service as foundry cupola blowing, atomizing oil for oil burners, supplying blast to heating and annealing furnaces of various kinds, blowing air for water-gas generators, pneumatic conveying and ventilating. They are of the single stage, double flow type and are furnished either electric motor, steam turbine or water wheel driven.

Jan 6, 1916

By R. S. Montgomery

Laboratory experiments simulating rock drilling were conducted on a number of commercial grades of tungsten carbide in order to determine their wear rates when they are used as inserts in percussive rock drill bits. The test rock was Barre granite and tests were made at conditions similar to those of the carbide buttons near the periphery of a large, down-hole, button bit. In addition, some wear rate measurements were made at a low blow energy. Wear rates of these carbide buttons were an extremely sensitive function of their cobalt contents and hardnesses and were proportional to e-°.57Hup to a hardness of about 91 RA. The point of minimum wear rate, which occurs at about 92 RA, corresponds to the point of maximum compressive strength. Modern percussive rock drill bits have inserts of cemented tungsten carbide on their wear faces. These inserts have drastically reduced bit wear in comparison to that of earlier all steel bits. The most common cemented carbide grade used in percussive rock drill bits contains about ten weight percent cobalt, although grades containing more or less cobalt are also used. Contrary to the case with carbide in metal-cutting tools, alloying materials are rarely used in mining grades. There are a number of designs of rock bits in current use. The most common form is an X bit which has four chisel-form radial wings. The button bit is another important design and one which has been recently developed. This design uses a flat steel face studded with relatively small hemispherically tipped carbide buttons. These types are illustrated in Fig. 1. Studies have been made of the sliding wear of cemented tungsten carbide on rock 1-4 and multiple-impact fracture', 5-6, b~t there has been comparatively little published on the percussive wear of this material although the wear of the impact face is the most important. There is some available data on the rate of dulling of rock bit inserts in actual drilling 7 but no laboratory studies. Sliding wear studies are useful for understanding the wear of coal and mineral cutting tools and gauge wear of percussive drill bits. but the

Jan 1, 1970

By R. E. Hummel, J. W. Koger

IT is generally accepted that the martensitic start temperature (Ms) can be determined by resistivity measurements and is that temperature where the resistivity vs temperature curve on cooling first deviates from a straight line.1-4 Both Titchener and ever' and pops5 have used resistivity measurements to follow the martensitic transformation in b1 Cu-Zn and ternary Cu-Zn-based b-phase alloys, respectively. Actually because of the nature of their measurements the temperature of minimum resistivity (M) was used by these authors to determine "Ms" . Also, due to experimental difficulties in detecting M, with resistivity measurements, Pops and Massalski 8 determined M, by optical microscopy. The present communication is concerned with high-precision, low-temperature resistivity measurements which reveal a definite M, temperature which differs from the temperature of minimum resistivity (M). It is also shown that M is merely the result of the geometry of the percent-transformation curve and the temperature coefficient of resistivity of the alloy. In other words, it will be demonstrated that M has no apparent significance (except that it denotes a temperature at which some percent of martensite can be detected in a given alloy). Alloy specimens were made by melting 99.999 pct Cu and 99.9999 pct Zn in sealed and evacuated quartz tubes and homogenizing them at 601PC for 300 hr. After the alloy was cold-rolled into foils suitable for resistivity measurements, it was quenched in ice water from 871PC. The chemical analysis showed a zinc content of 38.8 wt pct. The cooling rate during the martensite transformation was 1°C per min and was controlled with a thermistor. Electrical resistivity measurements were made using a K-3 type potentiometer; the reproducibility of the resistivity values was better than 0.03 pct. Temperatures were measured with a thermocouple to an accuracy of better than 0.2° C. Fig. 1 shows the resistivity vs temperature curves of the martensitic transformation in B1 Cu-Zn for both cooling and heating. The starting point of the martensitic transformation (M,) was taken as that

Jan 1, 1968

By T. O. Allen, J. H. Atterbury

Laboratory and field tests during the past five years indicated considerable variation in the penetrating power of commercially available gun perforators. Many of the guns which achieved inadequate penetration in these tests have since been improved. However, recent productivity tests indicated the possibility of inadequate penetration or, at least, ineffective penetration in some wells. Laboratory experiments under simulated well conditions have demonstrated considerable plugging of the perforations, apparently as a result of factors associated with the shooting process and/or the drilling mud in the well at the time of perforating. The restrictions to flow per unit of hole depth caused by this plugging appears to be greater for jet perforators than for bullet guns of comparable diameter; however, because of the greater depth of penetration obtained with the jet guns, the total flow rates appear to he approximately equal. Limited testing with an experimental shaped charge suggests that less shot hole restriction and greater flow rates may result from larger-diameter perforations or other factors related to charge design. INTRODUCTION Gun perforating has been accepted for a number of years as a routine well completion method which is often preferred since it permits more selective operation of producing zones. Nevertheless, questions have continued to arise as to the effectiveness of the communication paths established between the productive formation and the interior of the casing. The basis for these questions has generally been failure to obtain anticipated fluid production rates through gun perforated completions in specific wells. These low productivities, together with the frequent recovery of bullets from well bores, were considered strong evidence of inadequate penetration. Laboratory investigations of the penetration performance of many of the bullet guns available as late as 1948 gave support to these indications. Subsequent electrical analog studiesl,2,3 indicated that the depth of penetration required to provide productivities equivalent to open hole was beyond the capacity of most bullet perforators evaluated in the early laboratory penetration tests. These results, together with the advent of the shaped charge in the field of oil well perforating, stimulated the interest of both oil operators and service companies in gun development. Improvements in gun design resulted in jet and bullet guns which appeared to be capable of providing sufficient penetration for most perforating jobs. However, some wells failed to yield satisfactory fluid production even after being perforated with the more powerful guns, again raising the question as to the effectiveness of the perforating operation. This fact, together with preliminary shooting into targets prepared with formation cores, indicated that factors associated with the perforating process and/or the fluids in the well bore at the time of shooting may reduce effective formation penetration and thereby decrease well productivity. These laboratory and field data prompted another phase in the investigation of the effectiveness of gun perforating: a program to determine the extent and seriousness of perforation plugging under simulated well conditions.

Jan 1, 1955

By J. H. Schulman, M. H. Buckenham

R. W. Christy (Manager of Sales, Sanitary Engineering Equipment, Link-Belt Co.) and C.D. Rubert (Barrett, Haentjens & Co.) — Messrs. King and Schepman have presented an excellent paper which outlines the general practice in the design of thickener mechanisms. Lifting devices, controls, special applications and underflow pumping arrangements have been reviewed in detail. Pumping arrangements were illustrated which eliminate the need for an expensive tunnel beneath the thickener floor. Most of those illustrated have the common feature of a relatively long underflow suction line extending from the hopper floor to the pump located on the bridge at the periphery of the tank. The authors limit these arrangements to comparatively dilute or thin slurrys. It is implied that dense and coarse concentrates, which are difficult to pump, cannot be handled unless a tunnel is constructed. Fig. 1 shows an underflow pump arrangement which negates the need for a tunnel but which permits the operator to convey a heavy dense slurry. The pump is mounted directly on the fixed hoist platform and the impeller is located at the base of the steel center column. Priming water is not needed. The column

Jan 1, 1963