Search Documents

By Daryl R. Tweeton, Jerry R. Riding, Grant Buma, Frank J. Rosswog

In situ solution mining of uranium has environmental advantages over conventional mining. The leaching of uranium, however, alters the ground-water quality in the aquifer where the mining occurs. Currently, regulations require that the ground water be restored to approximately its original condition. This paper, a summary of a study funded by the Bureau of Mines, reviews the state of the art in restoring ground-water quality after in situ uranium leaching. Current restoration practices discussed include disposal of liquid wastes in deep disposal wells and evaporation ponds, producing from all wells during restoration, and recirculating water purified in surface plants. Methods for predicting the effectiveness and cost of current techniques are presented. Possible alternative techniques are also described. Two restoration operations are discussed.

Jan 1, 1979

By M. G. Fowler

A GENERAL decline in copper production for most American producers occurred during the past year as a result of shortage in available labor. Few noteworthy technical developments have been reported; undoubtedly, many changes and improvements have been made but have not been reported because of lack of time. During the war years through 1944 the pressure for sustained high production has been of prime importance and during 1945, with slackening of production, many operators were faced with the problem of catching up on repairs and maintenance of plants, with inadequate labor supply. In hydrometallurgy there were some important developments that undoubtedly will be reported during 1946. Several operators in the Southwest have instituted experimental leaching programs to exploit low-grade oxidized and mixed ore bodies. The Bureau of Mines is conducting pilot-plant experimental work to determine the possibility of producing a satisfactory sponge iron at an attractive cost from deposits of iron ore and coal in Arizona. The sponge iron would be used for the production of cement cop¬per. The cell house of the Inspiration Consolidated Copper Co. at Inspiration,

Jan 1, 1946

By C. E. Shoenfelt

The year 1939 witnessed the rapid development of several of the more important Rocky Mountain oil and gas areas and the discovery of new oil and gas fields. As a further result of an active year, many oil fields had their productive limits greatly extended or responded to deeper drilling with oil production in lower horizons. In Colorado there was a substantial increase in refinery capacity, with three new units constructed. Its contribution to the crude-oil supply was an important extension of the producing area of a Western Slope field and a deeper oil-producing horizon in an old field east of the Front Range. Occurrences of gas were reported in two wells in northwestern Colorado, but severe winter weather prevented tests and the value of these discoveries cannot be determined at this time. Montana's northern fields were extended and a number of record wells were completed. The North Cut Bank area gives promise of wide expansion in 1940. The gas-producing area of Wyoming's Elk Basin field was extended into Montana on the north plunge of the anticline. The most important developments in Wyoming oil fields in 1939 were extensions to the producing area of Lance Creek and the discovery of a deeper pay in the Tensleep formation at Wertz dome. A new gas field at Horn Valley in the south central part of the state was the only new field discovered, but wildcatting was at low ebb in Wyoming in 1939. Colorado In Colorado, the year 1939 saw the completion of several interesting tests, but largely with negative results. Oil was discovered, however, in a deeper sand in the old Fort Collins field and the productive area of the Wilson Creek field was extended. Gas had been noted in two Western Slope wells, at Yellowjacket-Buford and at Trull, but their volumes had not been determined at the end of the year. Of principal interest, however, were the failures, descriptions of which will be given presently. One of these established a new depth record for Colorado.

Jan 1, 1940

By C. E. Shoenfelt

The year 1939 witnessed the rapid development of several of the more important Rocky Mountain oil and gas areas and the discovery of new oil and gas fields. As a further result of an active year, many oil fields had their productive limits greatly extended or responded to deeper drilling with oil production in lower horizons. In Colorado there was a substantial increase in refinery capacity, with three new units constructed. Its contribution to the crude-oil supply was an important extension of the producing area of a Western Slope field and a deeper oil-producing horizon in an old field east of the Front Range. Occurrences of gas were reported in two wells in northwestern Colorado, but severe winter weather prevented tests and the value of these discoveries cannot be determined at this time. Montana's northern fields were extended and a number of record wells were completed. The North Cut Bank area gives promise of wide expansion in 1940. The gas-producing area of Wyoming's Elk Basin field was extended into Montana on the north plunge of the anticline. The most important developments in Wyoming oil fields in 1939 were extensions to the producing area of Lance Creek and the discovery of a deeper pay in the Tensleep formation at Wertz dome. A new gas field at Horn Valley in the south central part of the state was the only new field discovered, but wildcatting was at low ebb in Wyoming in 1939. Colorado In Colorado, the year 1939 saw the completion of several interesting tests, but largely with negative results. Oil was discovered, however, in a deeper sand in the old Fort Collins field and the productive area of the Wilson Creek field was extended. Gas had been noted in two Western Slope wells, at Yellowjacket-Buford and at Trull, but their volumes had not been determined at the end of the year. Of principal interest, however, were the failures, descriptions of which will be given presently. One of these established a new depth record for Colorado.

Jan 1, 1940

By C. G. Fink

A PART of the material incorporated in this paper was derived from the studies of ancient metal objects examined by the authors from time to time for museums and art collectors, in order to verify the age of the metal. The data thus accumulated during several years was systemati-cally surveyed and supplemented by new material obtained in examina-tion of a set of specimens that had been generously donated by museums for this study. Altogether over 50 pieces were investigated, of which 39 are described in this paper. Every specimen is at least 1500 years old; the majority are considerably older. Exact conditions to which these bronze and copper objects were exposed in the ground are unknown, unfortunately. It is safe to say that exposure conditions did not remain constant during the long period of burial. Although the collection of specimens studied represents a wide variation in location and age of the objects, as well as in the nature and composition of the metals, it was found that fundamental changes in the metal structure were limited to a few typical cases which, therefore, may be considered as more or less general. The authors' chief aim was to study the effect of extremely long periods of corrosion on the structure of bronze and copper.

Jan 1, 1936

By Richard H. Sprute, Dennis J. Kelsh

Slow-settling, fine-grained suspensions can often be dewatered and densified by applying direct current between buried electrodes. Although water removal rates and power expenditures depend on physical and chemical properties of the treated slurries, metal mine tailings from Idaho, Colorado, and Mexico have responded well in laboratory testing, as have 29 samples of ultrafine coal waste from mines in nine states. This Bureau of Mines report reviews field tests at two Idaho metal mines and describes the recent installation at the Henderson molybdenum mine near Empire, Colorado, and the treatment of coal sludge at a Clinchfield Coal Co. preparation plant near Dante, Virginia.

Jan 1, 1980

By Tell Ertl, Ernest E. Burgh

INTRODUCTION THE Bureau of Mines is operating an oil-shale mine 10 miles west of Rifle, Colo., as part of its Synthetic Liquid Fuels program. The purpose of operating this mine is twofold: First, to supply oil shale to an experimental processing plant; and second, to develop practices and select methods for mining oil shale on a commercial scale at the lowest practicable cost. The second purpose-that of finding out how to mine oil shale most cheaply-entails considerable mining research. Since the drilling of oil shale probably will be one of the major items of the mining cost, factors that influence drilling speeds were investigated. One phase of the drilling program was the development of a successful hard-surfaced rock-drill bit1 that can be used for drilling long holes in oil shale without changing bits. During that phase, drilling speeds were measured and drill cuttings were collected for assay and for screen sizing. When the cuttings from the individual tests were compared, a definite relationship was shown to exist between the drilling speed and the coarseness of the drill cuttings. PROCEDURE Measurement of Drilling Speeds All drilling in the tests was done with a Model UMB-D-99W Gardner-Denver wagon drill. Round-lugged drill steel, 1 ¼ in. in diameter was used in 6, 12, and 18 ft lengths with 2 1/8 -in. Timken H-type bits hard-faced with acetylene tube borium. The tests were made in the lower adit of the Bureau of Mines oil-shale mine; the grade of the oil shale drilled ranged from 18.6 to 42.7 gal per ton. During the experiments air pressure varied between 75 and 90 psi while water pressure remained fairly constant at 75 psi. All holes were drilled almost horizontally. Each drill hole was thoroughly cleaned of cuttings after being collared. The advance of the drill along the carriage was measured and recorded as the drilling speed in inches per minute. Method of Collecting Cuttings To facilitate the collection of cuttings, each drill hole was collared in a smooth, vertical portion of the oil-shale breast (Fig 1). A galvanized-steel sheet was fastened to the breast below the area in which the hole was to be drilled. The cuttings washed out of the drill hole by the drilling water were guided by the steel sheet into a wooden box. The cuttings that remained in the drill hole after the drill was withdrawn were scraped out and placed in the same box as the cuttings washed out of the hole. After the cuttings from a 1-min. drilling interval were collected, they were placed in flat metal pans. The fines were allowed to settle and the clear water was decanted. The cuttings then were dried in the sun.

Jan 1, 1947

By R. Schuhmann

Available thermodynamic data applicable to copper smelting systems are collected and tabulated, and the important gaps are pointed out. A few examples are given of estimations which can be made from the available data. An experimental research program is proposed to supply the thermodynamic data that appear most essential to better quantitative understanding of the chemistry of copper smelting. The proposed program is designed also to shed specific light on the practical problems of slag losses and magnetite behavior. OPPER smelting, from flotation concentrates to V-/ blister copper, is conspicuous among the large scale chemical processes which are conducted with only relatively incomplete knowledge of the physical chemistry involved. For example, no common metallurgy text explains adequately why copper enters the matte phase while iron enters only to the extent that sulphur is left over after satisfying the copper. Explaining this important phenomenon as a manifestation of the greater affinity of sulphur for copper than for iron is unsound because the affinities of copper and iron for sulphur are about the same at smelting temperatures. As will be shown, other affinities are really decisive in the relatively clear-cut separation of copper in the matte. In contrast, thermodynamic studies have contributed much to our understanding of copper refining, zinc oxide reduction, magnesium production, steelmaking, etc. For each of these processes, the important reactions are clearly recognized, and fair to good quantitative values of the free-energy changes and equilibrium constants are available. Such data have proved to be of constantly increasing practical value in process development and improvement. Work in other fields has furnished much thermodynamic data applicable to copper smelting systems. In fact, several promising starts have been made in applying such data to specific smelting problems. Kelleyl made an appraisal of the possibilities of recovering elementary sulphur from low grade matte. His calculations and compilations of thermodynamic data have represented the starting point for much of the work in this field, including the present survey. Huang and Hayward2 nd Aksoy3 used thermodynamic methods in the study of copper losses in reverberatory slags. Peretti4 used thermodynamic data in explaining the chemistry of converting. The recent publications of Darken and Gurry"." and of Darken,' dealing with the iron-oxygen and iron-silicon-oxygen systems, respectively, present equilibrium data that are applicable to copper smelting systems. Also additional data were reported recently on the affinity of sulphur for copper, manganese, and iron8 and on the sulphur pressures of iron-sulphur melts." The survey presented in this paper was made as the basis for planning an experimental program on the thermodynamics of copper smelting. Few researches on the chemistry of copper smelting have been reported in recent years, so that a reappraisal and coordination of old and new data are essential if further work is to take the directions of maximum value. The experimental program is now in progress, and the plan of attack is outlined at the end of this paper. Progressive Oxidation and Desulphurization of Copper-bearing Liquid Phases: The chemical activities of sulphur and oxygen are two of the most important thermodynamic yardsticks to be applied to copper smelting processes. Virtually the entire smelting and refining sequence involves a series of systems characterized by decreasing sulphur activity and increasing oxygen activity. In this section, therefore, an attempt is made to define and explain these activities in terms of equilibrium partial pressures of SO2, s2, and O,. Also, estimates of these quantities are presented, the estimates being based largely on calculations presented in a later section of this paper. The sequence of steps from raw flotation concentrate to fully oxidized copper ready for poling involves progressive and controlled oxidation. Iron is oxidized and enters the slag. Sulphur is oxidized and leaves in the gas. Table I summarizes several important features of this oxidation and desulphurization sequence, starting at the beginning of the matte blow in the converter. The top line gives in order the principal smelting and refining stages up to fully oxidized copper, plus the additional step, not used commercially, of oxidizing all the way to Cu,O. In the second line are shown the principal copper-bearing liquid phases which characterize the process. Through most of the sequence the copper

Jan 1, 1951

By B. D. Cullity, S. S. Hsu

The stress distribution at the surface of a twisted cylinder is analyzed along the boundary of a slip plane of arbitrary orientation and this analysis is applied to the torsion of cylindrical crystals of magnesium. A criterion for slip is developed and the critical resolved shear stress of magnesium in torsion is found to be 0.038 kg per sq mm. The mechanism of torsional deformation in magnesium and aluminum is described, as well as the relaxation of a twisted crystal at elevated temperatures. THERE has been considerable fundamental study A of the mechanism of slip occurring during deformation in tension and compression but comparatively little attention has been paid to the mechanism of torsional deformation. This paper is concerned with the way in which a single crystal deforms in static torsion and with the phenomenon of untwisting which a twisted crystal undergoes during annealing. Particular attention is paid to the application of the critical resolved shear stress law to torsional deformation. Probably the most likely mode of torsional deformation that can be imagined consists of rotation of one part of the crystal relative to another on the active slip plane. Here the most interesting feature is the slip direction. If a cylindrical single crystal is twisted about its axis and if, to consider the simplest case, the active slip plane is normal to the specimen axis, then the direction of gross slip at any point must always be at right angles to the radius drawn to that point. It follows that the crystallographic direction of slip must be continually changing, in sharp contrast to slip in tension which occurs in a crystallographically constant direction. Extensive investigations of slip in torsion have been made by Gough and his associates.' They made torsional fatigue tests on metal single crystals belonging to a number of different crystal systems and observed, with a microscope, the appearance of slip lines on the surface and of strain markings on the transverse cross section of cylindrical specimens. They concluded that the critical resolved shear stress law was just as valid in torsion as in tension, in the sense that slip occurred on that plane and in that direction in which the resolved shear stress was a maximum. They also established that the operative slip planes and directions were the same as in tension. They did not, however, measure the critical resolved shear stress in torsion nor, in fact, did they establish that a critical value of the resolved shear stress was necessary for the initiation of slip. Their investigations were, moreover, restricted to torsional fatigue tests which necessarily involve small strain amplitudes. Wilman,' studying crystal growth and the abraded surfaces of crystals, observed crystal fragments

Jan 1, 1955

By Frederick T. Fischer

INTRODUCTION Post-Lower Ordovician karstification on a continental scale produced a wide-spread paleoaquifer in the upper portion of the Knox Group of the Southeastern United States. The presence of economic zinc deposits in the Knox of Tennessee is considered to be a con- sequence of this paleoaquifer(1). During The New Jersey Zinc Company's initial exploration of the middle Tennessee region the known artesian nature of modern Knox water and its potentially adverse effect upon mining activities was a matter of concern. This concern intensified as a mining situation appeared imminent and a program of hydrologic investigation was begun in early 1969 and continued through August 1972. The preliminary findings of this work were reported at the AIME World Symposium on Mining and Metallurgy of Lead & Zinc in 1970(2). This paper presents additional data acquired during subsequent stages of the program and relates the hydrologic relationships to the overall geologic framework of the area. PHYSICAL GEOGRAPHY The Elmwood mine is 85km east of Nashville and 8km southeast of Carthage in Smith County, Tennessee (Figure 1). Its physiographic location is in the Central Basin of Tennessee, a basin resulting from erosional breaching across the Nashville Dome of the Mississippian strata which now form the bordering Highland Rims. Both the Central Basin and Highland Rims are divisions of the Interior Low- lands Province. Outcropping rock units of the Central Basin are predominantly Middle Ordovician limestones with scattered high hilltops capped by Devonian and Mississippian strata. One outlier

Jan 1, 1977

By John Devine

DURING the past few years the Bureau of Mines has been studying hydrogen-sulfide corrosion in the petroleum and natural-gas industries. Early work was confined to investigating the various practical, or operat-ing, factors that control the corrosion reaction when ordinary mild steel is being attacked. In that work it was shown that, if the optimum operating conditions1 are obtainable, . gas containing hydrogen sulfide can be handled at ordinary temperatures without serious corrosion resulting. However, frequently "sour" gas must be handled under other than optimum operating conditions, and combating corrosion then becomes a problem to be considered more during the construction of a system than during its subsequent operation. That is, where economi-cally practicable in such cases the designer will seek to substitute for mild steel other steels or ferrous metals more resistant to corrosion by hydro-gen sulfide. The comparative resistance of various commercial steels and alloy steels to corrosion by hydrogen sulfide at elevated temperatures has been reported systematically by previous investigators,2 but similar information for corrosion at ordinary temperatures is available only from scattered sources, representing different methods of testing. As the value of comparative corrosion tests depends largely upon the use of a

Jan 1, 1934

INTERNATIONAL GEOLOGICAL CONGRESS. (For further particulars apply to the Secretary, 12th International Geological Congress, Victoria Memorial Museum, Ottawa, Canada ; cable address, Geocong, Ottawa.) The Coal Resources of the World.-Three quarto volumes of about 400 pages each, 8 1/4 by 10 3/4 in., and an atlas of about 70 maps in colors, 13 1/3 by 19 1/2 in., bound in heavy paper cover. Edition limited to 3,000 copies, One thousand copies will be reserved for members of the International Geological Congress, and the remainder of the edition will be distributed in the order in which applications are received. Price, $35 per set. Ready in July, 1913. This book is an inquiry made upon the initiative of the Executive Committee of the Twelfth International Geological Congress, with the assistance of geological surveys and mining geologists of different countries, published by: Morang & Co., Ltd., Toronto, Canada. Headquarters During Session at Toronto. The headquarters will be a t the University of Toronto, where there will be a branch post-office open at all hours and at which registered mail may be received or despatched, money orders sent or cashed, etc. A hank will be established at which money may be exchanged. A typewriting service will be maintained, also a telephone service and messenger service. Railway and steamship agents will also be in attendance. A restaurant service providing luncheon in the middle of the day will be arranged.

Jan 8, 1913

By R. R. Templeton

THE year 1924 was particularly notable in the petroleum industry of California as it was a period in which extensive town-lot drilling, with attendant overproduction and allied problems, virtually ceased and the industry returned to a nearly normal condition. Nearly all major field operations were conducted by large operating and marketing companies; in contrast to 1922 and 1923 field operations, when small promotion companies set the pace and forced the large companies to follow. The outstanding features of petroleum development were: 1. The three major fields of 1923, namely Huntington Beach, Long Beach, and Santa Fe Springs, declined from a production of 13,042,939 bbl., in January, to 6,764,417 bbl., in December, a drop of nearly 52 per cent: During this period, Huntington Beach declined 35 per cent., Long Beach 42 per cent., and Santa Fe Springs 63 per cent. 2. Methods of pumping deep wells were improved in some particulars; this contributed toward sustaining the productions of these three famous fields above what was predicted. 3. Of the fields producing previous to 1924, only three increased in production to any appreciable degree, during the year, as the result of bringing in new wells. These fields are Dominguez, Torrance, and Wheeler Ridge. Dominguez, discovered in September, 1923, produced 56,851 bbl. in January and increased regularly to a production of 1,641,042 bbl. in December. Torrance increased from a production of 972,261 bbl. in January, to 1,783,670 bbl., in May, and then declined to 1,393,215 bbl. in December. Wheeler Ridge, discovered in January, 1923, produced 23,254 bbl., in January, 1924, increased to a high of 33,678 bbl., in September, and declined to 27,430 bbl. in December. 4. Nearly all the production that had been shut-in during 1923 was opened in 1924, except some wells chiefly in Coalinga, Fullerton, and Santa Maria districts. The opening up of this shut-in production, combined with the increased productions from Dominguez and Torrance, were the chief factors that held the rate of decline for the state to a gentle slope.

Jan 7, 1925

Jan 1, 1911

By F. L. Wolf, G. E. Alderson

The reclaiming of nietallics from slag and sweepings is of vital interest to every brass-foundry man, but the first cost and interest on the investment often make it prohibitive for the small foundry to enjoy the benefits of a complete concentrating unit. However, the cost of such an installation and the cost of operation are often exaggerated to such an extent that foundries dispose of their copper-bearing refuse at a great loss. This paper gives the actual costs and the returns obtained in the reclaiming plant used at the Ohio Brass Co. This plant is divided into two sections—the preliminary treatment and concentrating departments. In the former occur the screening, crushing, and hand-picking operations whereby rnost of the non-valuable and heavy metallic constituents are removed. The concentrating equipment consists of an elevator, bins, jigs, ball-mill, arid table. Preliminary Treatment The preliminary treatment varies, depending on whether the material is slag, foundry-floor sweepings, or brass casting-floor sweepings. Material of the first class is produced from the operation of six Steele-Harvey and six Schwartz furnaces; the second class represents sweepings from an average of thirty-five. molding floors per day: and the last is collected around the sprue cutters and knockout bench. Treatment of Slag The slag, analyzing 30 to 40 per cent. copper, is passed over a 3-mesh yard screen (Tyler standard mesh) stretched on an inclined rectangular frame supported by adjustable legs and equipped with a hopper which directs the undersize into a barrow. The fine product, running about 20 per cent. copper and representing 20 to 25 per cent. of the total slag, goes direct to a storage bin for concentrator frrd. The oversize is charged into a No. 2 Hill cinder crusher, which takes 175 to 200 11,. to a charge and crushes two charges per hour through 'a No. 4 riddle. It

Jan 1, 1921

NEW MEMBERS The following list comprises the names of those persons who became members during the period Dec. 10, 1915 to Jan. 10, 1916. ANDERSON, FRANK BASIL, Min. Engr., Sampler, Copper Queen Cons. Min. Co., Bisbee, Ariz. BAILEY, LEWIS NEWTON, Min. -Engr 4227 St. James Place, Sail Diego, Cal. BELL, JAMES E., Min. Engr., Care Chile Exploration Co., Chuquicamata, Chile, South America. BONILLAS, YGNACIO SAFFORD, Min. Geol., Copper Queen Cons. Min. Co., Bisbee, Ariz. BRADLEY, GEORGE OLIVER, Mech. Engr Hobart Bldg., San Francisco, Cal. CLARK, GEORGE L., Min. Engr Vipond Mine, Schumacher, Ont., Canada. CONKLING, RICHARD A., Geol., Roxana Petroleum Co. of Oklahoma, Tulsa, Okla. GOHRING, W. B.. Geol., Supt. of Mines, Calumet and Arizona Min. Co., Warren, Ariz.

Jan 2, 1916

By P. R. Kalischer

IN the production of alloys by powder metallurgical processes it is often necessary or desirable to include one or more components that tend to form very stable oxides Included in this group of metals are aluminum, manganese, magnesium, silicon, and a few others In many cases it is not necessary for the sintered compact to have full density and the other physical characteristics of a cast alloy and in that event no undue precautions need be taken If, however, it s required that the sintered part be entirely homogeneous, and have maximum density and physical properties, some method must be found to reduce the surface films of oxide, which are always present on the metals, and for the metals mentioned above this is always extremely difficult, if not impossible Since the production of high-density alloys is of particular interest to powder metallurgists, some experiments were undertaken to devise methods of reducing the refractory oxides For this work, alloys of iron, nickel, and aluminum were chosen because aluminum oxide is one of the most stable oxides and because these alloys in the right compositions form excellent permanent magnets All of the pertinent properties of the magnets could be accurately and delicately measured by density measurements and magnetic tests of sufficient scope to give a complete demagnetization curve From such a curve the maximum coercive force, residual magnetism, and energy products could be obtained and compared with the same properties for a cast material Any lack of homogeneity, density, or solid diffusion would be immediately apparent as a decrease in the magnetic properties NATURE AND REMOVAL OF SURFACE BARRIERS The early work of the present investigation was based upon published processes In the published information it was claimed that by intimately mixing iron, nickel, and iron-aluminum alloy (50 per cent Fe, 50 per cent Al) powders, compressing such a mixture into the desired shape and size, and then sintering (heating to a temperature below the melting point of the component metals) in hydrogen at 1200ºC or higher, a sound, homogeneous article could be made having the desired physical size, shape, and strength, and good magnetic characteristics However, this early work showed clearly that something in the powder compress was inhibiting diffusion and the process was almost entirely unworkable In the initial phase of the investigation samples of iron powder, nickel powder, and iron-aluminum alloy powder were pressed into separate bars and sintered in hydrogen Both the iron and nickel powders sintered

Jan 1, 1941

By I. Iwasaki, K. Adam

During wet grinding the electrochemical interactions between grinding media and pyrrhotite not only accelerate media wear but also adversely affect the suede mineral's flotation response. A possible remedy of the adverse effects on floatability by applying electric potentials to grinding media was examined. Flotation tests, Auger electron spectroscopy, and X-ray photoelectron spectroscopy were used to study pyrrhotite surface properties. Although anodic polarization of the steels increased metal loss by corrosion, pyrrhotite flotation recovery was increased. In the case of cathodic polarization, flotation recovery improved somewhat in a narrow range of overpotentials. At higher cathodic overpotentials, however, mineral floatability was progressively lowered although the corrosive wear of grinding media might be reduced.

Jan 1, 1985

By N. E. Norman, R. Stier

The mining industry is continually seeking out new and better underground mining techniques. One of the most recent-also, perhaps, the most significant-of the new concepts in underground mining is the use of mechanical rock-boring machines. And one of the problems that concerns us all in this matter is the cost of mechanical rock tunneling. To help answer the oft-quoted question "What will it cost me?" the following pages deal with the operating costs of so-called "medium to medium hard rock" boring machines-i.e., those designed to meet the drilling requirements in 8000 psi to 25,000 psi rock. A few machines are capable of drilling hard rock above 25,000 psi, but the economics of mechanical tunneling in rock that hard is limited at the present time. [ ] For mechanical rock tunneling, there are five main cost factors influencing the expense: Capital Investment, Cutters, Labor, Power Requirements, and Maintenance. These factors give us a good basic picture of the cost of excavation, although muck handling, erecting supports, and other costs directly related to conventional tunneling and mechanical boring enter into the final picture.

Jan 6, 1967

By Edward Martinez

Although the copper segregation process has been known as a method for treating oxide copper ores since the 1920's, the reactions involved in this process are still a matter of conjecture. However, the evidence turned up in a recent series of experiments at Asarco's Central Research Laboratories strongly indicates that some of the proposed reactions may not be occurring. Experimental work on oxide copper ores from the Sagasca mines in Chile led to the discovery of the copper segregation process in 1923. It was found that the reduction of the copper with coal at about 700°C occurred on the surface of the coal instead of remaining disseminated in the ore. The unusual behavior of the copper, which caused it to migrate from the ore particles to the coal, was traced to the presence of a small quantity of sodium chloride occurring in the ore. Further experiments with oxide copper ores proved that the presence of a halide, either occurring naturally or admixed with the ore, caused the copper to migrate from the ore particles and to segregate in the charge.

Jan 8, 1966