Search Documents

By Joseph C. Buchen

In principle, productiorl of salt from sea water is a simple operation. The sun and wind cause evaporation of sea water trapped in ponds, and what is left is principally salt. Commercial production, however, requires consideration of many factors. First is a high consistent annual rate of evaporation, as well as large areas of suitable low-lying ground close to economical shipping facilities. The south end of San Francisco Bay has these requisites. Large ponds are built, by using clamshell dredges to build up levees to a height of approximately 3 ft. on ground usually lower than sea level, so that the water may be taken in through tide gates without pumping. Ponds are divided into extremely large concentrating ponds and smeller crystallizing ponds. Approximately ten times more area is required for concentrating than for crystallizing. The concentrating ponds are irregular in shape and size but the crystallizing ponds are rectangular and fairly regular in size, to aid in harvesting. The ocean water is taken into the first of a series of concentrating ponds and gradually moved forward from pond to pond as it increase:: in density, reaehing the crystallizing area as a saturated brine. This brine is pumped into the crystallizer at the beginning of the net evaporating season, usually in May, and further evaporation causes its sodium chloride content to deposit on the bottoms of the ponds. The brine must be drawn off and a fresh supply added from time to time to prevent other undesirable salts from depositing with the sodium chloride. Harvesting usually begins near the end of August and now is accomplished almost entirely by mechanical means. After harvesting, the salt is stored in large sbockpiles until required for shipping or refining. The greatest amount is used for industrial purposes and is shipped without any processing other than screening, but all salt for domestic use produced by the Leslie Salt Co. is refined by the racuum process, giving a produet consistently testing over 09.9 per cent sodium chloride.

Jan 1, 1938

By George S. Koch

Since 1882, world zinc production has increased. In contrast, US zinc production rose until about 1915, but since then has remained nearly constant, with a slight tendency to decrease. Production from the Tri-State district, the largest early source of zinc in the US, has gone down steadily; this decline has been balanced by a growth in the rate of other districts. These changes in US production are due to economic, not geological, factors. Recent exploration has located large minable ore bodies: additional deposits will undoubtedly be found in the stratabound carbonate rock and volcanogenic environments. A statistical analysis of the exploration effort in the Middle Tennessee district indicates that new discoveries can be expected there. Thus, the US is in an early stage of the production cycle for zinc. Of major mining districts in the US, only the Tri-State is exhausted under current economic conditions; large zinc resources of low-grade material, which would repay mining at higher prices or improved technology, are known to exist in that district .

Jan 1, 1982

By Craig R. Barrett, Oleg D. Sherby

The creep characteristics of four pure metals with widely Varying stacking-fault energies (silver, copper, nickel, and aluminum) were evaluated above 0.5Tm. Creep tests were performed under conditions of constant atomic diffusivity and constant stress over the elaslic modulus. The sleady-state creep rate, Es, was found to he a funclion of the THE most common empirical representation of the steady-state creep rate, Es, at high temperatures and intermediate stresses is of the form where a is the applied stress, E is an elastic constant, A and n are constants (n is typically stacking-fault energ, y, such that Es is proportional to y3,5. In addition, it was uncovered that the primary creep strain and the strain to fracture increased with increasing y, and that the ratio of initial to steady-state creep rate decreased with increasing y. about 5), Q is the activation energy for creep (usually equal to that for self-diffusion), and kT has its usual meaning. sherbyl and McLean and ale' have used this expression to correlate creep data for a number of pure metals. An interesting aspect of Eq. [I] is the absence of any dependence on the stacking-fault energy. While most creep data seem to obey the stress and temperature dependence predicted by Eq. [I], when data for several metals are put on a master plot they do not fall on a common line but form a band. The width of this band corresponds to a variation in Es of 102 to l03. sherbyl attempted to explain this band by assuming that a grain-size effect was present which led to the observed variation. On the other hand, Felt-

Jan 1, 1965

By Charles E. Locke

IN gathering material for this review the aid of the individual members of the Milling Committee was invoked and the assistance received is hereby most grate- fully acknowledged. The replies were much alike; almost everyone stated that in 1932 his operations had been cur- tailed or stopped entirely, that the only activity and progress were in milling gold ores, and that the Hadsel mill' looked like a coming machine in the crushing and grinding field. However, further inquiry and search have shown that the year was not quite so barren of developments as the foregoing statement would indicate.

Jan 1, 1933

By Gerald, Sherman

INCREASED production and con¬sumption of all metals, indicate the progress of industry toward that condition formerly thought to be normal. With no market limitations on silver and gold the two new precious-metal mines, the Silver Queen (now the Golden Queen), in southern California, and the Sunshine, at Kellogg in northern Idaho have made progress toward a high routine production. The Golden Queen 300-ton mill is finished and ready. The Sunshine mill has been enlarged and production is now at the rate of 500 tons per day of high-grade silver ore. The Hecla Mining Co. is developing the Polaris vein, which should be the extension of the Sunshine to the east. Some rich ore is reported. The developments of the' East African Gold Fields, Ltd., in the Lupa gold field of Tanganyika Territory, have made good progress, but operation in an isolated locality is not rapid and a large plant will be required. There have been no other discoveries reported that can be compared with the three mentioned, but production has increased, with greater capacity in dredging equipment and underground mines more adequately prepared for production.

Jan 1, 1936

New Products Equipment

Jan 7, 1950

Jan 1, 1970

By Stanley J. Gasior, Albert J. Forney, Joseph H. Field

Most bituminous coal mined near Eastern industrial areas requiring high-Btu pipeline gas is caking and therefore unsuitable for fixed-bed pres- sure gasification by present techniques. If the caking property of such coal can be destroyed, the resulting fuel can be gasified in a fixed bed at pressure with steam and oxygen as a preliminary step in making a high-Btu gas. To find a practical way to convert strongly caking coals of granular or small lump size to noncaking fuel was the object of this study. In previous work, strongly caking coals of 1/8- to 1½ -in. size were converted to a noncaking coal char by treatment in a static bed in about 3 hours1 and coal of 18-100 Tyler mesh in a fluidized bed in about 5 min.2 An inert gas such as steam, nitrogen, carbon dioxide or a mixture of all three with a small amount of oxygen was used in both studies. In our work a strongly caking bituminous coal from the Pittsburgh seam of 4-8 Tyler mesh size was converted to a noncaking form in free-fall in about 2 sec by dropping it through a countercurrent flow of steam containing 4% to 7% oxygen at 1150º-1200°F and 300 psig. This method should also be applicable to smaller-sized material.

Jan 3, 1965

By Graham Bright

Before the arrival of central-station power, all coal and metal mines generated their own power and, in many cases, these isolated power plants gave a fair continuity of service. In coal mines that produce considerable gas, it is essential that power be available at all times for operating the ventilating fan and the hoist, if the mine is of the shaft type. In the case of an isolated power plant, if trouble should develop with the fan the men can be hoisted quickly when the mine is of the shaft type. On the other hand, if trouble develops with the hoist, the fan can be kept in operation, and there will be no necessity of haste in getting the men from the mine. Now that central-station power is being used so extensively for mine service, the continuity of service with gaseous mines is very important. : Inherently, the central station is much more reliable than any isolated plant, but trouble may occur on the transmission lines which may prevent the transmission of power for a considerable time. : Some mines have kept their steam equipment intact and ready for operation in case the purchased power should fail. This is expensive procedure, for the boiler plant must be fired at all times so that the emergency power will be quickly available. In a number of instances, gasoline-engine driven generators have been installed to furnish emergency power for the service hoist. As most service hoists are of the alternating-current type, the generator of the gasoline-engine driven set is usually of the a.c. type and is arranged to drive the service hoist motor at full speed, or an extra motor that can be thrown into gear on either the main or service hoist and the hoist operated at a greatly reduced speed. This arrangement is used because it is difficult and expensive to obtain and install large gasoline-engine driven units. The author has recently developed a plan by which the main hoist and the fan can both be operated at reduced speeds, in case of loss of power from a central-station power system. In this plan a gasoline-engine

Jan 1, 1923

By Graham Bright

Before the arrival of central-station power, all coal and metal mines generated their own power and, in many cases, these isolated power plants gave a fair continuity of service. In coal mines that produce considerable gas, it is essential that power be available at all times for operating the ventilating fan and the hoist, if the mine is of the shaft type. In the case of an isolated power plant, if trouble should develop with the fan the men can be hoisted quickly when the mine is of the shaft type. On the other hand, if trouble develops with the hoist, the fan can be kept in operation, and there will be no necessity of haste in getting the men from the mine. Now that central-station power is being used so extensively for mine service, the continuity of service with gaseous mines is very important. : Inherently, the central station is much more reliable than any isolated plant, but trouble may occur on the transmission lines which may prevent the transmission of power for a considerable time. : Some mines have kept their steam equipment intact and ready for operation in case the purchased power should fail. This is expensive procedure, for the boiler plant must be fired at all times so that the emergency power will be quickly available. In a number of instances, gasoline-engine driven generators have been installed to furnish emergency power for the service hoist. As most service hoists are of the alternating-current type, the generator of the gasoline-engine driven set is usually of the a.c. type and is arranged to drive the service hoist motor at full speed, or an extra motor that can be thrown into gear on either the main or service hoist and the hoist operated at a greatly reduced speed. This arrangement is used because it is difficult and expensive to obtain and install large gasoline-engine driven units. The author has recently developed a plan by which the main hoist and the fan can both be operated at reduced speeds, in case of loss of power from a central-station power system. In this plan a gasoline-engine

Jan 1, 1923

By Roger L. Goin

Maintaining smooth haulage roads is a key to significant cost savings at Kennecott Copper Corp.'s Bing- ham Canyon copper mine, located near Salt Lake City, Utah. The truck operations section of the mine moves an estimated 300,000 tpd of waste plus some ore to maintain a balanced production cycle. A three-year truck replacement program has produced a dramatic new look in both size and capacity of the truck fleet. Currently there are 95 haulage trucks in the Bingham fleet with capacities up to 150 t. The trend towards the larger haulage units places greater importance on overall truck availability. The impact of a 150-t truck being out of service is far more critical than with the former 65 or 85-t units.

Jan 12, 1974

By V. GUDKOV

THE iron-ore deposits of Russia were estimated at 2,200,000,000 by the Russian Geological Survey, in 1910; but this estimate must be considered as being far too low. The estimate for Siberia, which had been explored very little for iron ore, was placed at about 27,000,000 tons. The exploration, in 1912-14, of the three iron deposits-Blagodat, Baakal and Kamensk-raised the estimate of the iron-ore reserves or the Urals from 282,000,000 tons to about 400,000,000 tons. Conservative estimates of the explored deposits made by the writer in 1915, gave the following figures: Southern Russia 900,000,000 tons, Ural Mountains 500,000,000 tons, Central Russia 900,000,- 000 tons, Siberia 100,000,000 tons, Caucasus 20,000,000 tons, or a total of 2,420,000,000 tons of iron ore, or 1,200,000,000 tons of pig iron.

Jan 1, 1921

By H. Sigurdson, C. H. Moore

Extensive studies have been carried out on electric furnace and blast furnace slags obtained in the winning of iron from its ores. These slags normally consist of elements of the gangue minerals present in the ores, as well as the added flux materials. In consequence, melts of CaO, MgO, Al2O3 and SiO2 can be considered as representing typical slag compositions. When a slag of this composition cools, it usually crystallizes according to predictions possible from an equilibrium diagram of these constituents, providing the melt is not undercooled to form glass. The melt is either viscous or fluid, depending upon the ratio of binary cations to silica, and crystallizes easily or forms a glass for the same reasons. If the melt is not overheated so that carbides of the metal components of the slag are formed and if the composition of the slag is so adjusted that it has a high fluidity, liquid equilibrium is attained and the slag can be held in a liquid state for extended periods of time. Upon tapping, the slag crystallizes into minerals, the type and proportion of which are determined by the melt composition. Since equilibrium is attained, the holding period is not critical. In melts containing a large increment of titanium, however, the normal slag procedures are not applicable. Titanium, as one of the atomic transition elements, is, at elevated temperatures, capable of being reduced to form metalloid compounds much more readily than the refractory oxides present in normal slags. In consequence, an oxide melt containing titanium never reaches equilibrium in a reducing environment, but continues to shift its composition until cooled. If melts of this nature are cooled and samples submitted to metal-lographic and X ray analysis the course of reaction and crystallization in this type of slag can be determined. Preparation of Slag The slags investigated fell into the system CaO-MgO-TiO2-Al2O3-SiO2 and were produced from ilmenite ores reduced by carbon in an electric furnace. Since the equilibrium series1 and the laboratory smelting of ilmenite2 are described in two of the accompanying papers, detailed description of the smelting procedure is not required here. However, certain essentials must be mentioned. Two types of melts were used to produce slags studied in this investigation. The first series of smelts made to determine proper flux addition were produced in a 4 lb Ajax induction furnace. The charge, consisting of ore with the proper flux addition, was heated in a graphite crucible until fluid, held fluid for a sufficient time period to obtain 1-5 pct FeO content, and poured. Because of the small size of the charge only the final sample of these melts could be examined. In the melts made in the 50 lb arc furnace, however, grab samples taken at 10 min. intervals between time of initial melting and final pouring were available for examination. These samples allowed a much clearer picture of the course of reaction and crystallization. amounts of ferrous oxide and reduced titanium compounds is opaque to transmitted light. Therefore, all petro-graphic studies had to be made on polished slag sections. A representative sample of slag was cut or broken, mounted in a thermosetting plastic, ground flat using 400 grit silicon carbide, the coarse scratches removed with 600 grit silicon carbide and polished on billiard cloth using levigated alumina. Rouge was avoided because of the entrainment of the red particles in pores in the slag, causing a possible confusion with some of the mineral phases. In order to prevent sample projection above the plastic surface red bakelite was used to hold the sample, and backed up with clear lucite. In this manner sample labels could be permanently retained in the mounting. The polished samples were examined on a Bausch and Lomb metallograph at magnifications of 250 X, 500 X, 1000 X and 1800 X. The instrument was equipped for examination of specimens under bright field illumination and with crossed nicols. A magenta tint plate to aid in color tone differentiation was also used. Petrology of Slags In order to determine the composition and mineral relatinos of a previously unreported system petrologically, it is essential that the starting composition, reaction temperature and final composition be known. The chemical composition of the ilmenite ore used in these smelts is given in Table 1, and the complete analysis of a typical high titanium, low iron slag is given in Table 2. In the winning of TiO2 from ilmenite by a smelting process it is necessary to produce a slag which will melt at an economically feasible temperature, remain molten as the iron is removed by reduction, be fluid enough to be readily removed from the furnace, contain a high percentage of TiO2 and a low percentage of reduced titanium com-

Jan 1, 1950

EUGENE McAULIFFE, * St. Louis, Mo.-The method employed by the Engineer's Committee in arriving at a proper selling price for coal and coke represents hard painstaking effort based on a thoroughly scientific foundation; and the United States Fuel Administration can well point with pride to the work of this committee. The results so obtained placed

Jan 12, 1918

By P. I. Lipman

Largely forgotten by today's environmentalists and mineralogists is a pioneer scientist of the nineteenth century named Ellen Swallow. Fortunately, the memory of her accomplishments has been resurrected by Robert Clarke in his biography, Ellen Swallow: The Woman Who Founded Ecology. Her direct contributions to the field of mining included authoring First Lessons in Minerals and an analysis of the rare mineral samarskite which indicated the presence of an insoluble residue; her findings led to the eventual discovery of samarium and gadolinium. While enjoying the distinction of being the first woman student at the Massachusetts Institute of Technology, she successfully isolated vanadium in an ore which other experts had examined without detecting the metal.

Jan 1, 1974

By George W. Riter

(Canal zone meeting, November, 1910.) A DISTINGUISHED engineer, the active head of a large mining company, has said that surveying attains the dignity of a profession only in the hands of a few men-the few who know how to keep notes that will be understood by even a novice without further word of explanation. Of all mine-records, survey notes are perhaps the most important. The maps made from them serve as a working-guide, and as framework for other data ; and when, from any cause, access to underground workings is shut off, the surveyor's record often becomes invaluable. So seldom does a surveyor have a chance to check underground surveys by making a closure, that he is compelled to rely on the precision of each step of his work for the accuracy of the final result. When data are fully recorded on the spot, the notes, even in the hands of second parties, become evidence of the care and precision with which the surveying was done. It is worth a great deal to be able to pick up the work of a former surveyor where it was left o$; and to be able to carry it forward without retracing from the beginning. The purpose of this paper is to describe the survey-note system of a mine now under my direction, in which underground surveys had to be relied upon entirely for the proper division of rich ore-bodies between neighbors, thereby placing a premium on accurate surveying and permanent records. In survey-work, it soon turns out that paper is the least item of expense, and that little is gained by trying to economize note-book space. For many purposes it is best to record notes on cards or loose-leaves, which may be left in the office at the end of the day's work, and need not be carried into the mine again, there to become smeared with grime and grease. With the loose-leaf or card system, all notes relating to the same local-

Apr 1, 1911

By GEO H. DEIKE

NOT much activity has been evident during the past year in the establishment of co-operative scholarships but the interest among the coal-mining companies is more pronounced than ever. This is apparent from the replies received to a letter sent out by the Committee on the Promotion of Student Interest in Coal Mining to over 120 coalmine operating officials. With that letter was forwarded a bulletin issued by the school of mineral industries of The Pennsylvania State College entitled ?Industrial Scholarships ? a Partnership of Industry and Education.? In that circular was outlined the need for trained men in the war and postwar world, and particularly as such demands pertain to the growth of the mineral industries.

Jan 1, 1943

Objective stockpile goals have been met for antimony, bismuth, fluorspar, and iridium, while those for bauxite, cadmium, copper, lead, zinc, manganese, mercury, platinum, tin, and vanadium have not, according to a report by the Munitions Board. Total materials under inventory and contract represent about 78 pct of entire stockpile goals, the report stated. Frobisher, Ltd., of Canada has been given permission to survey power possibilities in certain lake and river basins in the Yukon believed to have a potential of 5 million he. Canadian Resources Minister, Robert Winters, also announced that his Government has rejected a bid by Aluminum Co. of America concerning use of Canadian waters to power a proposed Alaska aluminum project. Alcoa is reported hopeful of resuming negotiations.

Jan 3, 1953

By J. Gordon Parr, D. H. Polonis

RYSTALLOGRAPHIC relationships between martensitic a' (close-packed-hexagonal) and retained fi (body-centered-cubic) have been studied in binary alloys of titanium with manganese, molyb- denum, chromium, and iron.'" In these investigations, the habit planes of the martensitic phase were determined, as well as the orientation relationships between martensitic and parent phases. In each alloy

Jan 1, 1957

By C. C. Clark, J. R. Mihalisin, K. G. Carroll

OBSERVATIONS made in this paper were for the purpose of exploring the anomalous behavior of a particular heat of Type 310 stainless steel. The alloy, of nominal composition 25 pct Cr, 20 pct Ni, was observed to form a grain boundary precipitate at exceedingly high rates. A sheet of this metal, 0.060 in. thick, after cooling in air from 2000°F showed the presence of the grain boundary material, whereas none was found after water-quenching from the same temperature. X-ray techniques were applied without success and, in view of the ex-

Jan 1, 1958