Search Documents

By John B. Hastings

TEN miles from Hartsel, near Antelope springs, in Park county, Colorado, there is a large area of unconsolidated lake beds, which are interesting because at least a part of the lacustrine sands contains in the aggregate an immense amount of gold. During 1906, one of the arms of this dessicated lake was fairly well prospected with shafts and cuts by an Eastern company to test its value, as favorable amounts of gold had in some instances been found upon it. The claims of the company contain about 5,000 acres of the beds; but this is only a small portion of them, a south branch from a main body, which is at least 7 miles in diameter, with other and very wide lateral gulches, paralleling the one herein described on the east and west. A certain amount of digging and sampling was done in the outside areas; but the result was evidently unsatisfactory, since the work was discontinued. his section of Colorado has not been studied geologically, and the age of the ancient lake is unknown. It is probably Quaternary. I spent two weeks on the ground, in September and October, 1906, but was quite absorbed in the sampling. I looked, however, for terraces on the rim-rock and other evidences of movement and erosion, but did not find anything to denote an earlier age than the Quaternary. The granite rim-rock may be Archean; S. F. Emmons says that some of the granites in central Colorado are as old as that. The rim-rock as observed is a gray quartzose biotite-granite, except a small area in Sections 3 and 34, where it is a felsitic (?) breccia. The breccia is silicified by solfataric action at the corner near Shaft No. 7, in Section 34; but this action is older than the sands and does not extend to them. The shaft averaged 50c. per ton, more than twice as much as the rest.

Jan 5, 1908

By W. F., Dietrich

THIS paper deals with the- methods of mining the high-grade clays of California. Although the majority of the clay pits in the state are operated on a scale that is small by comparison with most metal mines, this very fact results in a diversity of methods and gives rise to problems of selection of the method best suited to given conditions. Two or three operators in California produce approximately 500 tons per day of a single kind of clay from a single pit. About five varieties of clay are mined on a scale of 200 to 400 tons per day; not over fifteen varieties are mined on a? scale of 50 to 200 tons per day; and more than 50 varieties are mined at a rate of less than 50 tons per day. It is the aim of this paper to delimit, insofar as the data at hand permit, the conditions and scale of operations that favor the selection of each dominant method of mining that is actually being applied at California properties. Details of the occurrence and utilization of the clays of California have been given in a recent bulletin and are not considered here.

Sep 1, 1928

By Chester O. Ensign

Many publications to date have advocated under- seas mining operations, optimistically overlooking the paucity of information on mineral distribution and the ocean environments in which minerals occur. Such articles (smattered with opinion, as is this article) are herein tempered by my more conservative views on the economics of mining under the seas. For purposes of this paper, underseas mining refers only to the deeper surficial deposits of the continental shelf and the deep sea floor, i.e., the deposits of phosphorite and manganese nodules.

Jan 9, 1966

By D. W. Brunton

THE maps of our large mines are usually prepared with the greatest care; and it is somewhat singular that, in comparison with the great amount of time and money spent in surveying and platting, so little actual use is made of them. Almost the only purpose for which a completed survey-map is afterwards consulted, is the determination of the relative position of the different workings to each other, and to the boundary-lines of the property. After the completion of such a map, it should be made the beginning of another, and in most cases a far more important, undertaking, namely, its utilization as -a starting-point for a complete inventory of the company's underground possessions. The ordinary mine-survey map, being nothing but a record of what has been done, is, in one sense, only ancient history. To increase its value, such additions should be made as will render it a complete statement of the amount and value of ore in sight at any particular time, and a guide for future develop¬ments. Comparatively little extra labor is involved in this undertaking, since the larger and most expensive part of the work has already been completed when the mine has been surveyed and mapped. The necessary additions consist in working out, and platting on the maps, the geology of the mine as exposed in the workings, in such a manner that the geological survey may be of daily use in the development and operation of the mine. The first step towards the production of a geological map consists in tracing individual level-sheets from the general or composite map. The area to be included, outside of the property in question, will depend very much on local conditions; but, for geological, legal and commercial reasons, it should be extended as far as reasonably practicable. The scale to be

Sep 1, 1905

By W. F. Domis, F. von Gemmingen, R. W. Whitmore, F. Garofalo

Constant-load creep-rupture tests at 1100°, 1300° and 1500°F were made on a Type-316, 18 Cr-8 Ni-ZMo, austenitic stainless steel to determine the relationship between ruptzire life and other aspects of creep behavior, The test program was designed on a statistical basis to check the variability of various creep properties and to determine emprically the dependence of minimutn creep rate and ruptzire life on initial stress, The dependence of the rupture life, tn, on the initial stress, a,, is found to be related to the stress dependence of the wrinimum creep rate, i,, and secondary creep strain, The instabilities or breaks found in the conventionual log - logt, plots can be traced to either a change in the linear dependence of log i, on log a, or to a change in secondary creep strain. In the alloy tested, rupture is found to be predowmanantly of the inter crystalline type, For this material, the secondary creep strain is -found to depend on the nature of the grain boundary precipitate, which affects grain boundary migration. It has been shown for a variety of metals and al tested at elevated temperatures under creep conditions that the empirical relationship exists between rupture life, tr, and minimum creep rate, i,. This relationship, in which C and a are in some cases independent of stress or temperature, shows in a general way that creep rupture depends on creep behavior prior to tertiary creep stage. To determine more fully the factors which control creep rupture requires, therefore, more knowledge of the relationship between rupture and creep behavior. To obtain such information, constant-load creep-rupture tests have been made on a Type-316, 18 Cr-8 Ni-2 Mo, austenitic stainless steel at 11000, 1300°, and 1500°F. These tests were designed on a statistical basis to determine the variability of the various creep properties measured and to determine empirically the stress dependence of minimum creep rate and rupture life. As a result of this work, various empirical relations have been established defining more closely the factor, C, in the relation between rupture life and minimum creep rate. This factor is found to be proportional to the amount of strain during secondary creep. The variation of secondary creep strain with rupture life and temperature is determined and its effect on rupture behavior discussed. The variability in minimum creep rate and rupture life is also dis- cussed and the dependence of these quantities on initial stress is interpreted. TEST MATERIAL AND TEST PROCEDURES The material tested is an austenitic stainless steel, AISI Type 316, of the following composition: C, 0.07 pct; Mn, 1.94 pct; P, 0.01 pct; S, 0.021 pct; Si, 0.38 pct; Cr, 18 pct; Ni, 11.4 pct; Mo, 2.15 pct; All 0.003 pct and N, 0.043 pct. The material was received as a hot-rolled 0.5-in. diam bar which was sectioned into 3.25 in. long blanks. Each blank was heat treated by holding 1/2 hr at 2000° F followed by water quenching. A 3/8-in. coupon was removed from each heat-treated blank and the microstructure was examined, the grain size determined, and the hardness measured. The microstructure was found to be uniform from blank to blank and the grain size was found to range from 4 to 6 ASTM numbers. Hardness, measured using a 20-kg load, varied between 127 and 148 Vpn. Tensile creep-rupture specimens having a 0.25 in. diam within a 1.5-in. reduced section were machined from the heat-treated blanks. Constant-load tests were made on these specimens at 1100°, 1300°, and 1500 F. Six specimens were tested at each stress level. Three creep-rupture machines were employed for tests at each temperature, two specimens being tested in each machine for each stress level. To minimize any effect due to local inhomogeneities along the length of the as-received bar the specimens were randomized before test. Each specimen was tested to rupture and in most cases an autographic extension-time curve was obtained. For very low stress levels at 1500°F no auto-

Jan 1, 1962

By B. C. H. Steele, C. B. Alcock

In choosing solid oxide electrolytes for use in the measurement of thermodynamic quantities at high temperatures, the two most important criteria are the values of the partial ionic and electronic conduc tizities. Measurements of these conducticities have been made for some Group IVA oxides and solid solutions of these oxides with CaO, Y2O3, and La2O3. The total conductivities as a function of temperature. oxygen partial pressure, and composition were determined, as well as the electromotive forces of cells in which the oxygen partial Pressures of the electrodes were between 10-7 and 10-29 atm at 1000°C. Additional factors that influence the experimental arrangements, such as the operating temperature, the appropviate cell atmosphere, and electrode kinetics, are also discussed. IT has long been recognized that galvanic cells incorporating solid electrolytes can possess many advantages for the measurement of high-temperature thermodynamic data. Unfortunately, the electrical-transport properties have only been established for a few solid electrolytes, although attempts have been made, and are still being made, to use such materials as porcelain' and magnesia.' Kuikkola and Wagner have discussed3 and demonstrated4 various applications of solid electrolytes, and, in particular, their work stimulated the electrochemical measurement of oxygen activities using cells incorporating the solid oxide electrolyte, Zr0.85Ca0.15O1.85 The excellent characteristics of this oxide electrolyte have been confirmed by the investigations of Kingery et al.5 (oxygen ion diffusion), Carter and Rhodes6 (zirconium and calcium ion diffusion), and Weissbart and Ruka7 (electronic transference number). However the observations of Peters and Mobius,8 later confirmed by Schmalzried,9 indicated that the electronic component of zirconia-based electrolytes could become significant at low oxygen chemical potentials. Under these conditions, thoria-based electrolytes have obvious advantages arising from their superior thermodynamic stability. It was known that certain thoria solid solutions possessed defect fluorite structures containing anionic vacancies (cf. Zro.85Cao.l50O1. 85), although data on their electrical properties were conflicting. Kiukkola and wagner4 concluded that thoria-based electrolytes exhibited appreciable electronic conductivity, whereas Peters and Mobius8 mentioned that the electronic conductivity only became important at high oxygen partial pressures, but gave no further details. In addition, both Kiukkola and wagner4 and Peters and Mann'" had determined the oxygen chemical potentials associated with the Fe-FeO, Co-COO, Ni-NiO, and Cu-Cu2O equilibria, and it was not known whether discrepancies in their results could be attributed to the different cell design, or the thoria-based electrolyte used by Peters and Mann. These uncertainties have been resolved during the present investigation into the measurement of low oxygen chemical potentials, and transport properties of the relevant oxide electrolytes are presented and discussed. Other experimental difficulties associated with low oxygen chemical potential measurements are also described, with particular reference to the Nb-O system. 1. THEORETICAL CONSIDERATIONS Oxide systems of potential use as solid electrolytes possess a large energy gap between the valence and conduction bands. Little is known about the defects present in these wide-gap metal oxides as a function of impurity content and deviations from stoichiom-etry, or the mechanisms by which electronic charges move in these solids. For these materials it is convenient to represent the measured conductivity as the the sum of three terms: where a, is the conductivity due to positive hole conduction (p type), and oe is the electronic conductivity due to electron conduction (n type). U there is a large concentration of ionic vacancies fixed by composition then the ionic contribution will not be a function of oxygen pressure. Although the possibility of a pressure-independent electronic component also cannot be ignored, it is likely that such a term would only become significant at very high temperatures, and in general the positive hole conduction will increase with increasing oxygen pressure, and the electron conduction will increase with decreasing oxygen pressure. It follows that the total conductivity is related to oxygen partial pressure as follows:

Jan 1, 1965

By A. D. Rovig, D. W. McGlashan, Donald M. Podobnik

Crystal-chemical and stntctural properties of sulfide minerals are considered. The information gained is to be used to interpret (I ) freshly broken mineral surfaces, (2) modifications of the mineral surfaces, and (3) reactions at the mineral surfaces. From these basic disciplines, concepts with regard to the changes that surfaces undergo, reactions that might take place, the geometry of the interface, the state of different atoms and ions in the interface, and other physical and chemical properties of an interface must be developed, weighed and applied. The authors first deal with these conceptual considerations from which hypotheses are set forth to describe the environ men tal-interfacial relationships for several sulfide minerals. Qualitative and quantitative explanation of par-ticulate solid separations are unknown entities because of the lack of adequate models and mathematical relationships to explain the activity occurring between the solid and liquid phases. It is a transitional region in which it is difficult to ascertain the mechanisms of adsorption of ions, molecules, etc., on mineral surfaces, as well as other secondary reactions which occur in interfacial regions. Thus, in this paper the authors deal with conceptual considerations from which hypotheses are set forth to describe the environmental-interfacial relationships for sulfide minerals. GENERAL CONSIDERATIONS Interfacial Reactions:Interfacial reactions are the cruxes of flotation schemes as well as other processes such as thickening, filtration and hydrometallurgy. However, as noted by Klassen and Mokrousov: 1 "The problems concerning the surfaces of natural minerals, the laws governing simultaneous adsorption from aqueous solution on these surfaces of a whole series of reagents, the laws of the surface reactions and the properties of water layers separating the minerals, are all known to a first approximation only." An investigator has the privilege of postulating methods of solid-liquid interfacial reactions. REACTIONS WITH WATER - Water consists of hydronium (H3 O 4) and hydroxyl (OH-) ions in the ionized state. That this is so forms the basis for the postulated reaction of the hydrated hydrogen ion with net-negative mineral surfaces as depicted in Fig. 1. In this case water is bonded to mineral surfaces through hydrogen-bridge-type bonds - possibly hydrogen bonds. Although bonding of the van der Waal type may be responsible for this reaction, it is most likely that stronger bonds are involved. Once firmly bonded to the surface, the water layer is known to be quite tenacious. It is further speculated that a shear plane exists at some distance (see Fig. 1) away from the mineral surface. Exact location of this plane is not known, but in all probability it will be positioned across a weak bond of the hydrogen-bond type where the surface-attached water is coordinated to the original hydrated hydrogen ion. REACTION WITH METAL IONS - Klassen and Mokrousov ' state: "The presence of an ion in water leads to an immediate formation around that ion of a highly condensed atmosphere of water dipoles and thus to hydration of the ion." The fact is known that multivalent cations are strongly hydrated, usually by six or eight molecules of water, and that anions are not so strongly hydrated. Conceding the fact that thermodynamics, concentration, pH, and physical considerations are of utmost importance in truly explaining a mechanism of metal ions reaction with a hydrated mineral surface, it does seem logical that the mechanism illustrated in Fig. 2 is feasible. In this reaction, the metal ion (M) is coordinated in one dimension - to the mineral-surface hydration layer. Note also that explanation of this reaction requires that the shear plane move to a less stable bond configuration; that is, the shear plane has moved to a position between the metal ion and the other coordinated water molecules which are more free to dissociate. Reactions as depicted in Fig. 2 should cause the formation of an apparent mineral surface which is net-positive. Immediately, it must be noted that measurements of apparent-mineral surfaces serve - within limits - to indicate a degree of ion-surface reaction capability. The major limiting factor he re is one related

Jan 1, 1970

By G. Bruggeman, K. G. Kreider

Grain boundary dij]usion coefficienls were measured in tungsten between 1400° and 2200° C and can be expressed by the equation sq cm per sec This activation energy confirms some eavlier estimates made .from tungsten sintering experiments. Grain boundary diffusion was found to occur in sub-bozrndavies having -misorientations of less than 10 deg. The actiuation energy for this subboundavy diffusion is equal to that for dijjusion in incoherent grain boundaries with in the limits of error. This is shown to be consistent with the dislocation model of Low-angle boundaries wheve diffusion occlcvs along- the dislocation 'YPipes" comprising -tile boundary. RECENT investigations of the sintering of tungsten powders all report activation energies which are considerably less than the activation energy for tungsten volume diffusion. Kothari' reports a value of 100 * 5 kcal per mole, Hayden and Brophy' obtained 90 kcal per mole, and Vasilos and smith3 found 110.7 kcal per mole from their sintering studies. Since most determinations of the activation energy for volume diffu-sion4-' fall between 120 and 160 kcal per mole (the true value seems most likely to be nearer 150 kcal per mole), the conclusion is drawn that the mass transport leading to densification during sintering is accomplished by grain boundary diffusion. This interpretation is consistent with various diffusion models of the sintering process. 10-12 Vasilos and Smith calculate diffusion coefficients from their data which fit the equation D * 1.36 x 10* exp(-llO,700/HD However, no direct measurements of tungsten grain boundary diffusion have been made. Furthermore, considerable disagreement exists between the directly measured values of tungsten volume diffusion.'-' In order to corroborate the inferred results of the sintering experiments concerning grain boundary diffusion and to provide accurate diffusion data essential to the analysis of the kinetics of creep, oxidation, precipitation, and so forth, the present work was undertaken to measure self-diffusion in single-crystal and polycrystalline tungsten between 1400" and 2200°C. It is within this temperature range that tungsten sintering is done, the re crystallization of tungsten occurs, and the widest application of tungsten as a high-temperature material will probably be made. EXPERIMENTAL PROCEDURE Radioactive WlE5 was produced by irradiating tungstic acid in a neutron flux of 1.2 x 1012 neutrons per sq cm per sec for 36 hr. A 2-week waiting period was allowed for the decay of w"~ also produced by the irradiation. (w"~ has a half-life of 24 hr.) The half-life of the remaining isotope was determined to be 75 days confirming the presence of w lE5 and the absence of any undesired radionuclide. Specimens 4 in. in diam and $ in. thick were cut from polycrystalline swaged tungsten rods (recrystal-lized) and from Linde single-crystal rods. Chemical analyses of these materials appear in Table I. Actually upon closer examination, the single-crystal specimens were found to consist of several subgrains separated primarily by tilt boundaries in which the misor-ientation ranged from 3 to 10 deg. Thus, it was possible to measure boundary diffusion coefficients in these low-angle subboundaries as well as in the incoherent boundaries of the polycrystalline specimens. The two faces of each specimen were ground flat and parallel within 0.0001 in. The radioactive tungstic acid was dissolved in concentrated ammonium hydroxide, placed on the ground flat of the specimen, and evaporated to dryness. The oxide was then reduced in hydrogen at 1000°C resulting in a layer of wlE5 approximately 1 p thick. The diffusion anneals were performed in vacuum in a tantalum resistance furnace. Time at temperature ranged from 10 hr at 1400°C to 2 hr at 2200°C. The penetration profile was determined by measuring the residual activity after successive removal of surface layers by grinding on metallographic polishing paper. Extreme care was exercised to insure that sections were always taken normal to the diffusion direction; this was verified repeatedly by checking that front and back surfaces of the specimen remained parallel. The activity was measured with an end-window Geiger-Mueller counter. The sides and edges of the specimen were well-shielded to eliminate possible effects due to surface diffusion. The weight of the

Jan 1, 1968

By Barry D. Lichter, Pierre Sommelet

High-temperature heat contents of InSb, GaSb, and AlSb were measured over the temperature range 400" to 1450°K using a diphenyl ether drop calorimeter. Smoothed ualues of the thermal properties, H$ - H:9s, have been derived and are tabulated at even temperature intervals. The heats of fusion of the three compounds were determined as, respectively, 5707 *100, 7780 * 100, and 9800 5 3011 cal per g-atorn at the determined melting points of 797" l°, 985" * , and 1330" * 5°K. The calculated entropies of fusion are, respectively, 7.16 0.12, 7.90 * 0.11, and 7.37 * 0.23 cal per deg per g-atotn. The heat capacities increase substantially on tnelting in contrast to the behauior of structurally related germanium and silicon. Deriations from the Kopp-Neumann rule are negative for solid compounds and positive for the liquid phases. Previously obsevrrd "post melting" in InSb is confirmed. The high-temperature thermal properties of 111-V compounds are presently not well-established, despite the technical importance of these semiconducting cbmpounds. Uncertainties in available heats of fusion and heat contents have seriously hampered thermo-chemical evaluations' and thermodynamic analyses of phase equilibria2"" in these systems. This paper reports results of high-temperature heat content investigations of InSb, GaSb, and AlSb measured in the range 400" to 1450°K employing a diphenyl ether drop calorimeter. Similar measurements for InAs and GaAs will be reported in a following publication.~ EXPERIMENTAL PROCEDURES Samples. High-purity samples of the compounds InSb and GaSb were supplied in the form of crushed crystal fragments by Dr. Carl Thurmond of the Bell Telephone Laboratories and in the form of single crystals by Dr. A. Strauss of the M.I.T. Lincoln Laboratory. Single-crystal samples of semiconductor-grade AlSb were supplied by Dr. W. P. Allred of the Bell and Howell Research Center. Chemical analyses indicated that all compounds were stoichiometric to *0.1 at. pct, which is within the experimental uncertainties of the analyses. Samples were crushed, weighed, and encapsulated in evacuated, thin-walled, fused silica capsules. The capsules were nearly identical in external shape, 2 cm by 2 cm diam, but varied in weight due to differences in wall thickness. One sample of AlSb was contained in a thin-walled, high-purity alumina cup encapsulated in silica and used for heat content determinations of liquid AlSb. The capsule materials showed no visual evidence of reaction with any of the compounds. The sample and capsule weights are given in Table I. Calorimeter. A Bunsen-type calorimeter, similar in design to a previously described instrument6 but employing diphenyl ether (C6H5)'0 as the calorimetric substance, was used for measurements of heat contents above 300.0°K, the melting point of diphenyl ether. Heat input to the calorimeter caused isothermal melting of diphenyl ether, and the resulting increase in volume was measured by displacement of mercury from the calorimeter into a 200 cm horizontal, calibrated capillary, 1.25 * 0.01 mm diam, or into a weighed beaker. The advantages of diphenyl ether over water have been previously pointed out7 and include: i) an increase by a factor of 3.5 in sensitivity as measured by the ratio of the volume change to the enthalpy change on fusion, ii) the smaller required extrapolation from the melting point to the standard temperature of 298.17"K, and iii) the positive volume change on fusion of diphenyl ether in contrast to the contraction which occurs on fusion of ice. Diphenyl ether was purified by fractional crystallization to 99.95 mol pct as determined from the melting point depression with fraction crystallized. During assembly of the calorimeter, the ether was repeatedly outgassed under high vacuum to remove dissolved air. The calorimeter receiving vessel consisted of an 8-in.-long by 1:-in.-diam copper tube with twelve horizontal 3-in.-diam radiator "fins" for dissipating heat to the surrounding mantle of diphenyl ether. Before forming the mantle the chamber surrounding the receiving vessel contained 3300 cu cm of liquid diphenyl ether above 250 cu cm of mercury which was

Jan 1, 1970

By N. E. Brown, F. L. Versnyder

THE apparent dependency of the electrical characteristics of hexagonal crystalline selenium on microstructure has aroused much interest in microscopical studies of selenium. Microscopic observations on the crystallization of selenium have been made by Escoffery and Halperin,' P. H. Keck,' and other investigators. It is the purpose of this paper to discuss the microstructural changes observed on polished cross-sections of single layers of selenium after various heat treatments. Observations were also made on crystallization of the free-surface layer of these deposits. In general, all of the transformations studied were either transformations of the vitreous selenium to hexagonal selenium or micro-structural transformation of the hexagonal selenium itself. Procedure The selenium used in this work was obtained from the American Smelting and Refining Co. and was approximately 99.96 pct pure. An intentional impurity of 1 part per 2,000 of bromine was added to the material prior to evaporation. A thickness of approximately 0.002 in. of this selenium was vapor deposited on an aluminum base plate. The maximum plate temperature during the vacuum vapor deposition was 140°C. Mounting of the cross-sectional specimens for metallographic study could not be done in plastic mounting media, as is customary, since temperatures in excess of 50°C would cause unwanted transformations. Consequently, a simple clamp-type device was used to mount the specimens for preparation. All grinding operations were then done carefully by hand in order that the specimen not become heated during this operation. Wet polishing was done on the conventional metallographic polishing laps, using successively finer grinding powders. An extremely careful polish is necessary, since observation and micrography of the specimens are done in the unetched condition under polarized light. The two observations of crystallization made on the free surface of vitreous selenium deposits (Figs. 4 and 5) were made on surfaces which were perpendicular to the cross-sections studied. These free-surface layers were examined directly, i.e., no pre- vious metallographic preparation, as obtained from the vacuum vapor deposition. Microscopic Observations A study was made of polished cross-sections of the vitreous selenium as-deposited. It was noted that in all cases there was columnar crystallization adjacent to the base plate, which appeared to occur during the vacuum deposition process. This observation has also been made by Keck? It also was observed that vagrant spherulitic crystallization occurred in the vitreous selenium. The term "vagrant" is used, since these spherulitic grains appear to crystallize at random throughout the vitreous selenium during the vacuum deposition process. Columnar crystallization at the A1-Se interface and a typical spherulite observed in a polished cross-section of "as-deposited" vitreous selenium may be seen in Fig. 1. Cross-sectional samples of vitreous selenium studied after heat treating individual samples for 20 min in 10" steps from 80" to 220°C revealed that crystallization—in this case, columnar crystal growth —proceeds from the aluminum base plate to the surface of the specimen (Fig. 2). Crystallization was microscopically observed to be complete after the 130°C heat treatment. Visual examination of the free surface of the specimen after the 130 °C heat treatment revealed the readily recognizable grey appearance of the completely crystallized selenium, in corroboration of the microstructural observations. No microstructural transformations then appeared to take place between 130" and 190°C. At 190°C the beginning of recrystallization appeared and proceeded until the columnar grain structure had been completely transformed to equiaxed grains between 210" and 220°C (Fig. 3). Naturally, the grain size of the recrystallized grains at the lower temperatures (190" to 210°C) was smaller than is illustrated in Fig. 3. In addition, polished cross-sections of deposits heat treated at 140°C for 10 min to cause complete crystallization and, subsequently, heat treated in 10" steps from 80" to 220°C for 20 min were studied. As expected, no microstructural transformations took place until the beginning of recrystallization was observed at 190°C. A comparison with the previously studied specimens revealed that recrystallization proceeded almost identically in the two experiments although in the first case the deposits were vitreous prior to the series of heat treatments and in the second case they had been crystallized by a previous heat treatment. By heat treating for longer times (180 min) at lower temperatures, the

Jan 1, 1956

By E. R. Helderman, C. Y. Ang, C. C. Nealey

Beryllium-base alloys have been successfully p7.-epared by the liquid-phase sintering technique. Depending orz the composition and amount of the intended liquid please, microstructures either single -phase or duplex in feature with randomly oriented grains have been obtained. Qualitative and semi-qualitative determination of distribution of alloying elements md microsegregations in some experi)uzental alloys haue been made by electron-micro-probe analysis in conjunction with microliardness testing and standard metallography. Tensile tests reoealed that some conzpositions possess attractive elastic properties with Young's mot1uli greater than 40 X 10' psi. In powder metallurgy, liquid-phase sintering is a process or phenomenon that has proven to be of practical value. For example, the heavy metals such as tungsten-copper-nickel, high-strength heavy gyro alloys,' heavy-duty electrical contacts,' and tungsten carbide tool materials are all products of liquid-phase sintering. Mechanisms involved in liquid-phase sintering, however, are not completely understood. Questions regarding the exact roles played by rearrangement of particles, liquid/vapor surface energy, solution and precipitation, and so forth, have not been completely answered. Evidence has been cited3 that at least volume shrinkage in the densification process is diffusion-controlled. It is possible that the predominant mechanisms for the complete densification and grain growth in a liquid-phase sintered system depend primarily on the alloy systems involved, in addition to processing conditions. Despite the lack of sound understanding of the mechanisms of the process, liquid-phase sintering has been and is being used to advantage either to synthesize microstructures for their special properties or to prepare alloys which are difficult to form by fusion process. Liquid-phase sintering of beryllium alloys was first attempted by Jones and Williams.4 They first tried infiltrating beryllium with magnesium, and then succeeded in preparing the alloy by sintering Be-Mg powder compact in molten magnesium bath. This investigation resulted in the identification of some Mg-Be intermediate phases. Crossley et a1.5 also used liquid-phase sintering technique in an attempt to produce ductile beryllium alloys for structural applications. The major liquid-phase components investigated by Crossley et al. were aluminum and silver with minor additives of germanium, calcium, lanthanum, cerium, and yttrium. The lack of wetting and the bleeding out of liquid phase were the difficulties encountered during experimentation. According to Hodge,6 the two compositions investigated by Crossley, which showed some promise based on compression tests, involved large amounts (over 35 wt pct) of silver, thus making them too heavy to be of practical interest to the aerospace industry and military users. The present investigation was prompted by the search for light-weight (density less than aluminum) beryllium alloys exhibiting small anisotropy in physical properties for precision inertial navigation instrument applications. In addition to isotropy, good structural properties such as high elastic modulus or desirable combination of mechanical and physical properties are also objectives of this investigation. The technique of liquid-phase sintering was chosen for its versatility in producing either duplex or homogeneous microstructures. This report is concerned with the use of copper and aluminum, with or without silicon addition, as the intended liquid phase, and the resultant micro-structures and some physical properties of the beryllium alloys. Qualitative and semiquantitative electron-microprobe analyses of some of the alloys are presented to illustrate the usefulness of this microanalytical technique for the identification of microconstituents and their distribution. EXPERIMENTAL PROCEDURES The beryllium powder used was -200 mesh Brush Beryllium Co. QMV NP-50 grade. Typical chemical analysis of the powder is shown in Table I. Commercial high-purity copper, aluminum, and silicon powders all screened to —100 mesh were used as additions. Mixed powder compositions were ball-milled in ceramic jars for 1/2 hr to ensure thorough blending. Milled powder was loaded either in 3/4-in.-diam button die or in Metal Powder Association flat tensile specimen die and compacted under top and bottom pressure. No lubricant or organic binder was used. Sintering was carried out in a quartz tube under a vacuum of 50 to 100 µ pressure. Surface hardness and some microhardness readings were taken on sintered specimens. Sintered density was

Jan 1, 1965

By R. Taggart, D. H. Polonis, W. C. Gallaugher

In the Ti-Cu system, the a' phase can be produced over a wide range of alloy composition witJwut the retention of measurable amounts of the ß or ? phases. This paper reports on the decomposition of this hexagonal martensite phase front the standpoint of solute corzcentratiorz, tempering temperature, and coherency strain condition. The mechanism of precipitation during tempering comprises localized precipitation which is followed by discontinuous precipitation if sufficient coherency strains are present. The localized precipitation process in hypoeutectoid alloys is described by the generalized Johnson-hiehl equation and an activation energy of 46,000 cal per mole. In hypereutectoid alloys the corresponcEing activation energy is 51,000 cal per mole. The rate-controlling process has been proposed as the difision of copper along a' platelet interfnces. SEVERAL investigations have been reported concerning the kinetics of decomposition of the mar-tensitic a' phase in titanium binary alloys.' In the Ti-Mo system,' two modes of a' decomposition have been observed in the presence of /3 phase; one of these involves the precipitation of fine a from a', and the other involves diffusion across the a'-ß interface. In studies of the Ti-Cr system, Rostoker2 did not detect the formation of TiCr2 during tempering. In Ti-Ni alloys,3 the intermediate phase Ti2Ni has been found to precipitate directly from a' along the interfaces between plates. With the exception of the study of Ti-Ni alloys the previous investigations of tempering phenomena in substitutional martensites are mainly qualitative and do not present a detailed description of the precipitation processes. The following limitations restrict the correlation of the microstruc-tural processes and reaction kinetics during tempering in most binary-alloy systems. 1) A mixture of at least two phases characterizes the constitution of quenched alloys. 2) Difficulties have been encountered in obtaining uniform structures throughout quenched samples. 3) The reaction products, and in particular their morphology. have not been clearly resolved. 4) The martensitic a' phase forms over only a limited composition range for most titanium-base binary alloys. Gomez and polonis4 showed that the Ti-Cu system provides an excellent basis for investigating the tempering of a' over a range of composition without the complication of retained P or the transition w phase. In the present work the effects of solute concentration, tempering temperature, and coherency strain conditions are considered with reference to the over-all precipitation process in quenched alloys of the Ti-Cu system. Both microstructural observations and kinetic data are correlated to define the rate-controlling processes which govern the observed localized and discontinuous precipitation reactions. An earlier paper5 was devoted to a discussion of the modes of heterogeneous nucleation of Ti2Cu from the martensitic a' structure. The present paper will therefore emphasize the progress of the tempering reaction beyond the initial stages. EXPERIMENTAL METHODS The Ti-Cu alloys for this study were prepared by conventional arc-melting procedures. Chemical analysis revealed that the alloy buttons contained approximately 0.02 wt pct 0, 0.04 wt pct N, and within 0.1 wt pct of the intended copper concentration. The progress of the tempering reaction was followed by means of electrical-resistance measurements utilizing a Kelvin double bridge, microhard-ness readings with a 400-g load, and X-ray dif-fractometry patterns to reveal line-broadening effects. Metallographic specimens examined at magnifications greater than X1000 were shadowed with germanium to reveal fine structural details. Direct carbon replicas were prepared for the electron-microscopy studies. EXPERIMENTAL RESULTS Property Changes. The changes of microhardness that accompany the precipitation of Ti2Cu from a' are shown in Figs. 1 and 2. As the solute concentration increases the peak hardness, for a given tempering temperature, increases. In alloys of given composition the time to reach the peak hardness agreed with the time to attain maximum X-ray diffraction peak breadth, as shown in Fig. 3. The maximum hardness and the maximum line breadth increased with lower tempering temperatures, and the time to reach the maximum also increased. The a' peaks broadened during the initial stages of tem-

Jan 1, 1965

By J. C. Cook

In solution-mining of underground salt and similar minerals, using drilled wells for access, it is desirable to monitor the lateral growth pattern of the resulting fluid-filled cavern. Therefore, a process of seismic surveying from the surface of the ground has been conceived in which the amplitudes of waves reflected from and transmitted through the soluble formation are measured. The large acoustic impedance contrast between solid and fluid should produce striking amplitude anomalies, especially if shear waves are employed, since thick fluid bodies are opaque to shear waves. Horizontally-polarized (SH) shear waves are best for preventing conversion to P waves at the numerous horizontal interfaces in the ground. Field tests to date have shown that a truck-mounted, half-ton hammer striking horizontally against the end of a trench produces usable SH-wave energy at lateral distances up to about 850 ft. Horizontally-directed explosive wave sources were effective to about 2000 ft. Conventional magnetic-tape recording and processing were used, but with the detecting geophones oriented to favor SH waves. An irregular solution cavity in bedded salt at 500-ft depth has apparently been located by SH-wave and SV-wave reflections. Further field work is planned to corroborate and extend this result. The Brine Cavity Research Group, an association of 11 chemical and salt producing companies, is supporting this work. Major deposits of salt in tabular beds lie beneath some 300,000 sq miles of land in the central and northeastern U.S. This salt is a basic source of soda ash and chlorine, and has been extracted as brine from drilled wells for about a century. During the past two decades, the U.S. solution-mining industry, following the lead of European operators, has greatly improved the extraction process through the application of engineering and science.' In 1957, the Brine Cavity Research Group, an association of 11 chemical and salt producing companies, was formed. This group proceeded to attack certain common problems through the support of research. An outstanding problem has been that of determining the shape and location of the growing solution cavities in the underground salt, so that measures can be taken to maintain operating efficiency. The problem has been partially solved by the Dowel1 sonar mapping service, which employs a pulse-echo device lowered into the cavity through the well.2 However, the working range of this equipment is at present insufficient for large cavities, and echoes are not returned from highly sloping walls nor from behind such obstructions as rock debris. Therefore, an independent means of mapping the cavity, for example, from the surface without interfering with operation of the well, would be desirable. THEORY OF THE METHOD Seismic waves are the only physical agent known to be capable of sufficient resolution and penetration to define typical solution cavities from the surface of the ground. The geometry is unfavorable: cavity widths are generally less than half their depths below the surface; resolution and lateral location of boundaries and channels to within 50 ft at depths of 500 to 3000 ft is desirable. Conventional seismic surveying, as used for petroleum prospecting, is probably not the answer: isopach mapping, for example, is not thought accurate enough to define the cavity by the slight additional delay time it would introduce (of the order of 0.005 sec for a 50 ft-thick cavity in hard Paleozoic rocks). Refraction surveying has also been considered, but seismic specialists see little promise in it for this problem. In 1957, in correspondence with industry personnel, the writer suggested a seismic method based upon careful measurement of reflection amplitudes. As Table I illustrates, seismic reflection coefficients r for typical brine-rock interfaces are considerably higher than those for typical interfaces between different kinds of solid rock. This fact can be utilized in two ways, illustrated in Fig. 1: 1) If the cavity roof is reasonably flat (which it may sometimes be since the unsaturated top brine will be in contact with an insoluble rock stratum), extra-strong seismic reflections will be received from the salt stratum where the solid has been replaced by liquid.

Jan 1, 1964

By E. S. Machlin, Morris Cohen

The martensite reaction in single crystals and polycrystals of 70 pct Fe-30 pct Ni alloys is shown to be autocatalytic in nature, producing bursts of transformation during cooling. The temperature of the first burst of transformation, called Mb, occurs below M, in these alloys. Experiments were devised to test the athermal embryo and strain embryo theories of martensite nucleation. The results indicate that internal strains, either within the virgin austenite or around existing martensitic plates, control the nucleation process in these alloys. Furthermore, the growth of martensitic plates is not limited by the attainment of an elastic balance with the austenitic matrix, but by the occurrence of plastic deformation at the martensite boundaries which interferes with the propagation mechanism. IN an investigation of the martensitic habit in single crystals of a 69 pct Fe-31 pct Ni alloy,' it was observed that about 25 pct of the austenite transformed during subatmospheric cooling within the time-interval of an audible click. This event proved quite spectacular: The shock wave sent out from the specimen freely suspended on a thread in the refrigerating liquid was occasionally sufficiently intense to shatter the Dewar container and to separate the toluene column in the immersed thermometer. The Present investigation was undertaken to determine- the kinetics and mechanism of this "burst" type of martensitic reaction. The analyses of the alloys studied are given in Table I. The composition of the single crystal specimens is designated by alloy A, while the polycrystal-line specimens were made of alloys B and C as noted in the text. The single crystals were prepared in a vacuum furnace, using a modified Bridgman technique. Most of these crystals were homogenized by holding for 24 hr at about 1300°C just after solidification. However, it may be emphasized here that the degree of homogenization was not a controlling factor in the subsequent experiments, inasmuch as specimens having different degrees of homogenization yielded the same results. All of the single crystals were fully austenitic as slowly cooled to room temperature. An illustration of the burst phenomenon is given in Fig. 1, which shows oscillograms of electrical resistivity and temperature vs. time during the continuous quenching of 1/16 in. wire specimens (alloy B) in a dry ice and acetone bath at —77°C. There are at least two observable bursts in this case, as indicated by the sharp decreases of resistance accompanying the sudden formation of substantial quantities of martensite. The thermal arrest during the quench probably corresponds to the larger burst. Usually the bursts are followed by more or less progressive transformation during continuous cooling. It will also be noted that the resistance continues to decrease after the specimen has reached the bath temperature. This isothermal change denotes the formation of martensite at constant temperature, and will be the subject of another paper. Examination of fiducial scratches on the surface of a transformed single crystal has shown2 that the scratches in adjoining nonparallel martensitic plates are usually bent in opposite directions, as though one plate forms in such a way as to relieve the matrix stresses set up by the adjacent plate. This, together with some of the results described in ref. 1, Table I. Compositions of Alloys Studied, in Percent Alloy Ni C N Mn Si P S Cr A 31±0.3 0.048 0.027 0.003 0.56 0.007 0.002 B 29.5±0.2 0.036 0.02 0.19 0.09 0.008 0.006 C 19.99 0.52 0.37 0.47 0.010 0.015 0.04 led to the tentative concept that a cooperative action exists which provides the impetus for much of the transformation that appears during the burst. The following series of experiments were performed in order to test this idea. Cooperative Nature of the Burst Two adjacent disks, Va in. thick x % in. diam, were cut from a single austenite crystal of alloy A using a jeweler's saw. One of the disks was then cut into 15 parts. Then 12 of the latter pieces and the second disk were austenitized (stress relieved) at 600°C for 30 min and water quenched to room temperature. The temperatures at which the first burst of transformation appeared were determined for

Jan 1, 1952

By P. R. Hines

Diphenyl guanidine is used as an accelerator in vulcanizing rubber. Other rubber accelerators are also flotation collectors, e.g., dithiocarbamate, thiazole, and the xanthates. Urea and its derivatives are good flotation collectors,' and guanidine is the nitrogen analog of urea. These two characteristics suggested testing diphenyl guanidine as a flotation collector. Diphenyl guanidine has been tried in flotation work previously, but references give no details.'.' Bunker Hill Co. of Kellogg, Idaho, supplied the ore sample used in these tests. The sample was typical of the ore milled in 1949 and contained 4.52 pct Pb and 1.08 pct Zn. A flotation test made by the author with potassium ethyl xanthate as a collector, the same flotation reagents, and the same grind employed in regular Bunker Hill mill practice was the standard for comparing results with the compounds and derivatives of guanidine. The compounds and derivatives of guanidine are only fair collectors of galena. However, if potassium ethyl xanthate were used in the galena float, its presence later in the sphalerite float would make it impossible to introduce another type of collector and be certain which collector contributed the result, so the compound or derivative of guanidine under test was used in both the galena and sphalerite floats in Table I. On both the galena and the sphalerite in the Bunker Hill ore, the depressing action of sodium cyanide and zinc sulfate is much greater with collectors of the guanidine type than with the xanthates. If the depressing agents are left out when a guanidine type of collector is used, but a pH of 8.6 is maintained with either lime or sodium carbonate, the depressing action is approximately the same as in the standard xanthate test. Consequently the depressing agents, sodium cyanide and zinc, were not used in the galena floats of tests 1226, 1228, and 1286, Table I, so the galena floats would be on a comparable basis with the standard xanthate test. As shown by the tests in Table I, the loss in the tail when diphenyl guanidine is used is 8.3 to 9.3 pct, as compared to 17.6 pct with potassium ethyl xanthate, or a recovery of 2.3 to 2.0 lb more zinc. Concentrate grade is 13.7 pct with potassium ethyl xanthate and increases to 22.9 and 31.8 pct with diphenyl guanidine, showing a much higher selectivity. Unless the Barrett's No. 4 coal tar creosote is considered to be a collector, no collector other than diphenyl guanidine is present in the tests, Nos. 1226, 1228, and 1286. Tests 1218, 1253, and 1263 in Table I1 were run to check the effect of the depressing agents used in flotation of the galena (sodium cyanide and zinc sulfate) upon subsequent flotation of sphalerite by diphenyl guanidine. Urea was substituted for potassium ethyl xanthate in tests 1253 and 1263 because it is a good collector for galena and a poor one for sphalerite, and the effect of the depressing agents is more marked with urea than with potassium ethyl xanthate. Test 1205 checks the effect of urea alone without any depressing agents when used for the flotation of galena. Table I1 shows that diphenyl guanidine as a collector for sphalerite is compatible with other flotation reagents used in floating galena. When the depressing agents sodium cyanide and zinc sulfate are used in the galena flotation step, the amount of lime in the sphalerite flotation must be increased (compare 1253 and 1263). Table I11 gives some of the compounds of guanidine which were tested and compared. Some of the compounds and derivatives of guanidine* are solu- * Diphenyl guanidine is in commercial production and is available on the market. ble in water and others are not. Those tested were fed dry. When an organic collector is promising, its compounds and derivatives should be tested and their comparative collecting power recorded. Eventually, in this way, it may be possible to discover some of the essential chemical characteristics of a good collector. For example, it is interesting to compare the diphenyl and dibutyl derivatives in Table IV with those of urea in Table 111, Example 3, U. S. Patent 2,664,198. All are good collectors. Table I shows some of the effects of lime on recovery of sphalerite by diphenyl guanidine. Table V

Jan 1, 1960

By Joseph Lindmayer, Karl M. Busen

If silicon is in contact with silicon oxide, a heterojunction is formed which induces an inversion layer ("channel"). Influences of impurities and structural parameters on the channel are discussed. There seems to be no relation between surface damage in silicon and the channel. Phosphorz~s doping of the silicon oxide has no pronounced effect on the channel. Channels which were well above the range predicted by the heterojunction model were related to the action of H* at the silicon/silicon oxide interface. Channels which were well below tlze range predicted by the heterojunc-tion model were related to a transition region in the oxide adjacent to the interface. In support of the assumed transition region and the H+ are the ex-periments described on the paper. Furthermore, the concept of metastable OH groups in silzca, known from other publications, has been used to explain certain channel characteristics by the formation and the accommodation of hydrogen in the silicon oxide. THE electrical characteristics of a semiconductor device in many cases are influenced by the conditions of its surface. Because these conditions often are changing with temperature, time, ambient, or other parameters, numerous attempts have been undertaken to stabilize them by suitable processes. Several years ago Atallal studied the silicon/silicon dioxide interface and since then increasing attention has been given to the silicon dioxide as a means to stabilize silicon surfaces. This led to the evolution of the planar silicon devices where oxide layers are used to protect places at which the junctions are intersecting the surface. The formation of the oxide layers on silicon can be carried out by a variety of processes: high-temperature thermal oxidation (exposing the silicon surface to oxidizing agents such as 02, HzO, COz), evaporation of SiOz, or anodic oxidation of silicon. Originally the oxides were considered able to "passivate" the silicon surface and it was understood that they 1) protected the surface against any influence from the ambient and 2) stabilized surface conditions which were necessary for proper device performance. It soon was realized that the second quality was not always obtainable: Atalla and Tannenbaum showed that, in the process of forming a layer on doped silicon by thermal oxida- tion, electrically active impurities in the silicon near the interface are redistributed, thus giving rise eventually to the formation of unwanted charge distributions. The degradation of planar junctions during reoxidation of silicon was observed by Barson et a. Surface studies with silicon planar junction structures indicated that the breakdown voltage depended on the kind of procedure which was applied during or after oxidation.*" Yamin and worthinge report on charge storage and dielectric properties of SiOz films at elevated temperatures. Another influential parameter on the silicon surface is discussed by Lindmayer and usen,' namely the appearance of a surface potential on silicon as a consequence of the heterojunction formed by the silicon/silicon oxide interface. In the present paper the influence of impurities and structural parameters in silicon oxide in connection with the heterojunction is a particular object of our investigations. I) EXPERIMENTAL The material used was 10 ohm-cm p-type silicon slices with either damaged surfaces (mechanically lapped or polished) or damage-free surfaces (chemically polished). The majority of the slices were oxidized for 1 hr and 20 min at 1250°C in a steam + oxygen atmosphere generated by passing O2 through HzO at 90°C (wet oxygen). This led to oxide layers of about 9000 A. On some slices oxide layers were grown in pure oxygen (dry oxygen). By a photoresist process a set of 20 by 200 mil windows was then etched out from the oxide layer. The pattern of the windows is shown in Fig. 1. In a subsequent process n-type pockets with surface concentrations between 2 x 10" and 5 x 10" cm"3 were formed by phosphorus diffusion. This allowed ohmic contacts between the silicon surface and tungsten probes which for electrical measurements were placed into two adjoining windows and

Jan 1, 1965

By A. D. K. Laird, C. A. Johnson

Drag coefficients for a cylinder being towed through water at constant velocity and also at constant linear acceleration were measured. Drag coefficients for constant velocity towing showed reasonable agreement with previous results. The drag coefficients found for constant acceleration showed little correlation with either the magnitude of the acceleration or the value of the modulus AD/V2 and tended to be slightly lower than those for constant velocity. INTRODUCTION For the design of offshore structures, wave forces acting on immersed cylinders are of importance. Several investigations have been made of these forces and of how they can be predicted from wave theories. A paper by Crooke' summarizes much of the work already done. More recent research by the Wave Research Laboratory at the University of California, Berkeley, has added much to the body of data collected under ocean wave conditions, but has not found a reliable method of force prediction from basic theories of wave motion. The present investigation is part of a long-range program to collect data with which to test current and future theories and correlations. The immediate objective was to measure drag forces on a circular cylinder subjected to linear accelerations over the range of Reynolds numbers between l04 and 105 where the drag coefficient was a constant for constant velocities. In particular, the effect of constant acceleration from rest and from uniform motion was to be investigated. The effect of acceleration may be evaluated in terms of drag coefficients. A useful resistance coefficient, C, is defined by the equation for total drag force, D, exerted by the fluid on the cylinder. DT =CSp V2/2.........(1) The coefficient C may be plotted as a function of the parameter AD/V2. Here D is the diameter and S is the projected area of the cylinder. The acceleration and velocity are A and V. The mass density of the fluid is p. An alternate drag coefficient, C, corresponds to the total force of the fluid opposing the motion minus the virtual mass force. This drag coefficient, arising from the velocity of the fluid, may be compared with that for the same cylinder in uniform motion. The similarities and differences between this coefficient as calculated for accelerated and for steady motion are of interest in the inverse process of predicting drag forces on cylinders under arbitrary conditions. One serious difficulty in this method is the specification of the virtual mass which depends also on the flow picture about the cylinder.1 EXPERIMENTAL EQUIPMENT The experiment was performed in the combination wave and towing tank at the Engineering Field Station of the University of California. The tank is 200 ft long, 8 ft wide, and 6 ft deep. The tow carriage is externally propelled by a cable, and the velocity of the carriage is maintained essentially constant by means of an am-plidyne. For the purpose of the present investigation, the speed control of the amplidyne was modified by inserting a linear speed control rheostat, which was rotated at a constant speed by a small d-c motor equipped with a slip-clutch. Accelerations which were constant over a reasonable length of time were thus produced. The magnitude of the acceleration depended upon the speed of the d-c motor and the limiting speed of the carriage. Data were obtained for a range of accelerations of 2 to 10 ft/sec,2 and a range of velocities of 2 to 15 ft/sec. An accelerometer (Statham Type C-2-350) with a range of ±2g was attached to the carriage and connected to a Brush analyzer and penmotor. A continuous coil of wire with 10 turns/ft wound around a fixed wooden form extending for a distance of 40 ft along the length of the tank was connected by an electrical contact mounted on the carriage to a Brush analyzer and penmotor, to give the time-position history for each run. The test cylinder was machined from solid aluminum alloy, 17-ST. to a diameter of 1.250 in., and could be

Jan 1, 1957

By N. E. Rogen, N. J. Grant

WHILE direct measurements of the growth of precipitate particles during aging is of fundamental value, few such measurements have been made. Direct measurements by means of optical or electron-microscopy and X-ray techniques are preferred, however, many of the aging studies have been based on indirect methods such as electrical resistivity and hardness. Because of the minute size of most precipitate particles (less than 1000A) the light microscope is of limited use while electron microscopy is subject to slowness, etching problems and consequent resolution problems. It is fortunate that alloys of the Nimonic type, based on Ni-Cr-Ti-Al, lend themselves to accurate and relatively easy particle size measurements. With proper balance of titanium and aluminum, the only aging precipitate is the gamma prime (r') Ni3,(Al, Ti)2 phase and this phase is the basis of the high-temperature strength of these allos.3-6 The Ni3(Al, Ti) phase is a face-centered-cubic, ordered structure with nickel atoms occupying the cube faces. Titanium atoms can replace three out of every five aluminum atoms and when substituting do so preferentially.2 Electron microscopy has shown that during aging of most of the commercial alloys of this type, precipitate particles are unusually uniform in size and distribution, and that the volume of (r') phase is large (20 pct).4,7 The aim of this investigation was to measure the growth of (y') phase during aging. In so doing, it was hoped that a clearer understanding of the aging process would be attained. X-ray line broadening was used as the measure of precipitate particle size. This technique was selected because it can measure and average the diameter of thousands of particles in one operation. The variations in hardness and matrix lattice parameter with aging were also studied and related to the particle size. EXPERIMENTAL PROCEDURE An alloy of the following composition was studied: Cr Ti A1 C Ni Wt pct 20.71 2.98 1.43 0.04 bal. At. pct 22.06 3.47 2.95 0.18 bal. The alloy, a 15- lb vacuum melt, was forged to 1/2-in. diam at a temperature of 1900" to 2200°F; was solution heat treated for 4 hr at 2000°F and water quenched; and was then aged in various ways. The ASTM grain size was 4 to 5. No (7') phase could be detected by X-ray analysis after solution treatment and electrolytic extraction. Aging was performed on 2-in. long specimens at 1400°, 1500°, and 1600°F for increasing times. One-half inch sections were removed after each time increment and were then electropolished in a solution of H3P04 saturated with chromium trioxide at a potential of 30 v and rectified with a tantalum electrode. Rockwell hardness measurements were taken using one side of the polished specimen. Matrix lattice parameter determinations were made on the other side using filtered chromium radiation references with the position of the (220) line of a silicon standard. To enable the precipitate particles of the (y') phase to be measured using X-ray line broadening techniques, it is first necessary to separate and concentrate this phase by electrolytic extraction. Extraction is necessary because the difference between matrix and precipitate lattice parameters is only approximately 0.5 pct and intensities of.the (y') phase lines are very weak relative to those of the matrix. The extraction techniques employed have been described before and found to produce a reasonably quantitative separation.398 A water solution of 15 pct H3Po4 is used at a current density of 0.5 amp per sq in. at 6 v. The precipitate particles are separated from the liquor by centrifuging and decanting and are then washed, dried and repowdered. A plot of the X-ray intensity vs diffraction angle for the (111) line of the precipitate particles was used as a measure of particle size. The intensity curve approximated the shape of Gaussian distribution function and its breadth was measured at the half height. The (220) line of a silicon standard was used to correct the measured line breadth for instrumental and other broadening errors. The Scherrer formula was used to calculate particle

Jan 1, 1961

By Elmer A. Jones

Development work in mines of St. Joseph Lead Co., Southeast Missouri, using trackless loading equipment shows definite advantages: Speed of cleaning, ability to work on steep grades and sharp crosscuts, good later tracking conditions, and possibility of wasting rock in old abandoned stopes.

Jan 1, 1950

By Stanley W. Ivosevic

The South-Central Osa Peninsula produced around 30,000 kg (100,000 troy oz) of gold since prehistoric times. Gold freed by erosion from quartz lodes in the Mesozoic Nicoya ophiolite complex was reconcentrated through three generations of Quaternary sedimentary deposits. Resultant gold placers grade upward from 1 g/m3 (0.03 troy oz/m3) and are of moderate size.

Jan 1, 1980