Search Documents

By A. P. Young, F. C. Holden

IN many of the early investigations of the aging of titanium alloys, it was observed that the retained beta phase could be aged to a high hardness without an apparent change in microstructure; moreover, in some alloys it was found that even a very rapid quench produced beta having an anomalously high hardness. What appeared to be hard beta phase was designated as "beta prime," to distinguish it from the softer normal retained beta phase. Frost and co-workers'.' demonstrated that the increased hardness is caused by the formation of a metastable phase, omega, which can be identified from its X-ray diffraction pattern. This reaction also has been studied by Brotzen, et a1.,3 and the structure of the omega phase has been published by Silcock, et al.," and by Austin and Doig.3 The X-ray diffraction analysis by Austin and Doig indicated that omega is low in alloy content, approaching the composition of the stable alpha. The aging process proceeds by the path Thus, overaging results in the formation of alpha and the ultimate disappearance of omega. This is accompanied by a decrease in hardness and a recovery of ductility. The present work represents a study of the aging process in a high-purity Ti-6.4 Mn alloy, in which optical and electron microscopy, X-ray diffraction, and hardness data were correlated. The specimens, 1/8-in. sections cut from 1/4-in.-diam rod, were heated in argon to a temperature just into the beta field (810°C), held for 1 hr, and water-quenched. The aging samples were heated in air for 1 hr at 300 to 500°C. The specimens were ground and mechanically polished, finishing with alternate etching and polishing on a slow-speed wheel to remove disturbed metal from the surface. The surface finally was swab-etched, rinsed with tap water, and air-dried. The etchant used was an aqueous solution containing 1 1/2 pct HF and 3 1/2 pct HNO3. This procedure is identical with that used for preparing metallographic specimens, except that the optimum degree of final etching required for electron microscopy may vary from that used for light microscopy. Metal replicas, backed with silica, were prepared from plastic strip-pings for examination with the electron microscope. Complete details of the procedures used for preparing these replicas are available elsewhere." Fig. 1 shows a comparison between the structures revealed by the electron microscope and those obtained by conventional light microscopy. Hardness and X-ray diffraction data are listed in Table I. No evidence of a second phase is apparent in the optical micrographs for the as-quenched sample, or for the specimens aged at 300 or 400°C; fine alpha particles can be seen in the specimen aged at 500°C. In the electron micrographs, visible equiaxed pocks appear in the as-quenched specimen, and, with increasing density, in the samples aged at 300 and 400°C. After aging at 500°C, the structure becomes markedly coarser and develops an oriented appearance of a second phase, coincident with the appearance of visible alpha particles in the light micrographs. These observations are confirmed by X-ray diffraction and hardness data. In these specimens, aged for 1 hr, the intensity of the omega pattern increases to a maximum at the 400°C aging temperature, corresponding to maximum hardness and the maximum density of pocks in the electron micrographs. At this point the beta phase shows a definite enrichment in Mn. At 500°C, little or no omega re-

Jan 1, 1959

In the special number of the magazine Ocl und Kohle (Oct. 22, 1940) dedicated to the petroleum industry of southeastern Europe, there appeared several articles relating to Yugos1avia.t In the first article the author calls attention to the fact that there are two fields in Yugoslavia that have been explored and exploited by more than 100 wells at variable depths during the last 50 years. These are on the Island of Mura, at the confluence of the Mura and the Drave. Additional exploration drilling in various other parts of the country has been without result, but certain ones of these explorations have revealed the existence of gas horizons that have some value, which are being used for industrial purposes. Table I shows the production of oil and gas between the years 1900 and 1939. TaBle —Production of Oil ad Gas in Yugoslavia . n,i Natural Natural Years oil Years Gas, Cu. Years Gas, Cu. Meters Meters T900-1929 10,000 1923 507,000 1934 1,388,000 1930 277 1924 567,000 1935 1,401,000 1931 202 I92S 691,000 I936 1,483,000 t932 289 19261 1.472,000 1937 1,841,000 1933 629 1927! 1,732,000 193s 2,431,000 1934 324 1928 2,515,000 1939 2,628,000 1935 260 1929 4,700,000 1936 137 I93O 5.345,200 1937 463 1931 6,376,153 1938 1,091 1932 1,661,737 1939 1,114 1933 959,574 The number of wells drilled from 1884 to the present time was in the neighborhood of zoo and the total footage drilled was 65,000 m. up to July I940 They may be divided roughly as follows: 12 wells in the region produce natural gas; 134 wells in the two old fields of the Island of Mura and about zo wells for the exploration of the zone of the Flysch, in Bosnia. The depths of 50 of these wells was roo to 200 m.; the depths of 50 wells oil the Island of Mura ran from zoo to 500 m.; of 2 ; wells, 500 to I000 m.; of ro wells from rooo to 2000 meters. The deepest well drilling in Yugoslavia has reached 2000 in. In the Valley of Morave, in the region of Selnica, I00 km. south of Nish, there have been discovered asphalt-bearing limestones, which contain about 15 per cent asphalt and are associated with bituminous clays. Later, at Paclenica, important deposits of natural gas were found. A zone rich in gas and oil seepages runs through Pracec, Miklenska, Bujavica, etc. The author studied these regions from the point of view of stratigraphy and tectonics. The anticlines and gas-bearing domes are concentrated in two zones: the region of the Drave (Island of Mura) and the region of the Save, southeast of zagreb, which contains the gas field in exploitation in the region of Bujavica. A full description of the productive region of the Island of Mura has been given by Egon Bohm, a geologist, in the second article mentioned. This includes a history of the exploration and exploitation that took place under Hungarian rule in this region. The most important exploration was effected between 1884 and 1885 by Stavenov and Stinger, of Vienna. In 1927 work was done in the same region by Anton Raky, a well-known explorer who makes work of this kind his specialty.

Jan 1, 1941

In the special number of the magazine Ocl und Kohle (Oct. 22, 1940) dedicated to the petroleum industry of southeastern Europe, there appeared several articles relating to Yugos1avia.t In the first article the author calls attention to the fact that there are two fields in Yugoslavia that have been explored and exploited by more than 100 wells at variable depths during the last 50 years. These are on the Island of Mura, at the confluence of the Mura and the Drave. Additional exploration drilling in various other parts of the country has been without result, but certain ones of these explorations have revealed the existence of gas horizons that have some value, which are being used for industrial purposes. Table I shows the production of oil and gas between the years 1900 and 1939. TaBle —Production of Oil ad Gas in Yugoslavia . n,i Natural Natural Years oil Years Gas, Cu. Years Gas, Cu. Meters Meters T900-1929 10,000 1923 507,000 1934 1,388,000 1930 277 1924 567,000 1935 1,401,000 1931 202 I92S 691,000 I936 1,483,000 t932 289 19261 1.472,000 1937 1,841,000 1933 629 1927! 1,732,000 193s 2,431,000 1934 324 1928 2,515,000 1939 2,628,000 1935 260 1929 4,700,000 1936 137 I93O 5.345,200 1937 463 1931 6,376,153 1938 1,091 1932 1,661,737 1939 1,114 1933 959,574 The number of wells drilled from 1884 to the present time was in the neighborhood of zoo and the total footage drilled was 65,000 m. up to July I940 They may be divided roughly as follows: 12 wells in the region produce natural gas; 134 wells in the two old fields of the Island of Mura and about zo wells for the exploration of the zone of the Flysch, in Bosnia. The depths of 50 of these wells was roo to 200 m.; the depths of 50 wells oil the Island of Mura ran from zoo to 500 m.; of 2 ; wells, 500 to I000 m.; of ro wells from rooo to 2000 meters. The deepest well drilling in Yugoslavia has reached 2000 in. In the Valley of Morave, in the region of Selnica, I00 km. south of Nish, there have been discovered asphalt-bearing limestones, which contain about 15 per cent asphalt and are associated with bituminous clays. Later, at Paclenica, important deposits of natural gas were found. A zone rich in gas and oil seepages runs through Pracec, Miklenska, Bujavica, etc. The author studied these regions from the point of view of stratigraphy and tectonics. The anticlines and gas-bearing domes are concentrated in two zones: the region of the Drave (Island of Mura) and the region of the Save, southeast of zagreb, which contains the gas field in exploitation in the region of Bujavica. A full description of the productive region of the Island of Mura has been given by Egon Bohm, a geologist, in the second article mentioned. This includes a history of the exploration and exploitation that took place under Hungarian rule in this region. The most important exploration was effected between 1884 and 1885 by Stavenov and Stinger, of Vienna. In 1927 work was done in the same region by Anton Raky, a well-known explorer who makes work of this kind his specialty.

Jan 1, 1941

By W. A. Backofen, D. Lee

Tlze condition of superplasticity or neck-resistanl flow that results front high strain-rate sensitivity has been observed in isothermal tension tests on several titanium alloys and one of zirconium hi general, il was associated with reasonably fine-grain micro-structures being stvained in the transformation range at rates below i - 10 -3 sec-&apos;. The metallographic mean-free path, L, was measured at room temperature after rapid cooling from the temperature of test-ing. The flow stress of Ti-GAL-4V at 950°C was proportional to La at different constanl <; the value of a decreased with increasing. E but at E< 1.5 x 10-4 sec-1 it varied only from 0.9 to 1.25. The findings were interpreted to mean that viscous boundary shear is the rate-controlling process of deformation at high levels of strain rate sensitivity in these materials. Elongation of over 1000 pet could be obtained, but a1 temperatures so high and rates so low that any practical application of the full effect would probably be difficult. As the transformation range was narrowed, by turning from Ti-6AL-4V to Ti-5Al-2.5sn to nomznally pure titanium, the allowable temperature varialion was correspondingly reduced. Superplasticily was not found in Armco iron, presumably because the transformation range was too narrow to allow the developtnenl of a reasonably stable microstructure for isolhermal lesting. THE work represented by this paper grew out of a recent study of texture hardening in a(hcp) titanium and zirconium-alloy sheet,&apos; of which part has now been published.2 It was found that, with heating, the tensile plastic-anisotropy index, R,* was decreased from well above 1 towards 1 as the temperature range for the a(hcp) -ß(bcc) phase change was entered. The clearest example of that trend is illustrated with previously unpublished data in Fig. 1. It might have been thought that such a development resulted simply from introduction of the cubic and therefore plastically less anisotropic phase. However, the accompanying change in the index of tensile strain-rate sensitivity, m = a log a/a log E, was rapidly upwards, to a high of 0.85 in some cases (also illustrated in Fig. 1). At the same time, the total tensile elongation rose to a maximum and the flow strength dropped away as R (and m) approached 1. Taken together, the observations cannot be understood as resulting from the presence of cubic phase, per se. It has been concluded instead that they reflect the largely noncrystallographic deformation which characterizes superplasticity. As demonstrated in other recent work? a necessary condition for super-plasticity is strain-rate sensitivity of flow stress sufficiently high that m is above a lower limit of -0.3. The origin of large m has been traced, in turn, to grain size so small that a substantial amount of viscous deformation is introduced by such processes as Nabarro-Herring diffusional flow4 and/or grain boundary shear.5,6 Because of problems in the processing of titanium and zirconium alloys—problems of high strength, limited ductility, and excessive springback, originating largely in slip resistance-it was natural to wonder if something useful might be done with superplasticity in those materials. Therefore experiments were made for more closely identifying and generally bounding the phenomenon with temperature and strain-rate limits, before attempting to decide about its exploitation. The results are being reported here. EXPERIMENTAL Materials. The two of primary interest were the titanium alloys of nominal composition (in wt pct) 5A1-2.5Sn and 6A1-4V. Others were a 4A1-1/4O2 titanium alloy, titanium of commercial purity (RC-70), Zircaloy-4. and Armco iron. All were received as annealed 3/16 in. thick sheet, except RC-70 which was & in. thick, and tested in that condition. Details of transformation temperature and grain size are given in Table I. The results of dilatometry for the measurement of transformation temperatures were unsatisfactory. Data were finally obtained by metallographic examination of each specimen after test, to determine from the amount of transformed 4 where the specimen had been heated in relation to the critical temperatures. Results were in reasonable agreement with information from the supplier. Strip tensile specimens were of full sheet thickness and taken along the rolling direction, except for those

Jan 1, 1968

By F. Claisse, R. Angers

Self-diffusion in iron has been measured during rapid a-r transformations using a variant of the Kryukou and Zhukhovitskii diffusion method. The study was performed by thermally cycling iron foils (1 to 6 cpm) through the transformation (=910°C). Some foils have been subjected to over 1000 cycles and some have spent more than 15 pct of their total diffusion time in the process of transformation. The experimental results show that the a-r transformation has no measurable effect on self-diffusion in iron. The study is completed by a quantitative analysis of mechanisms which can affect the diffusion rate during the transformation. The analysis confirms the experimental results. SINCE diffusion is an important factor in many solid-state transformations, it is of interest to study how it is affected by the stresses generated during these transformations. Clinard and Sherby1&apos;2 were the first to make a study along these lines. They measured diffusion coefficients in Fe-FeCoV couples subjected to slow thermal cycling (1.5 cph) through the a-r transformation range. They found an enhancement of diffusion by a factor of about two. The purpose of the present paper is to report measurements of the self-diffusion coefficient of iron during much more rapid thermal cyclings (1 to 6 cpm) through the a-r transformation (-910°C). These more rapid cyclings produce higher strain rates during the transformation and should emphasize any possible influence of transformation upon diffusion. EXPERIMENTAL Iron foils, 25 to 35 µ thick, were cold-rolled from 99.92 pct pure iron and annealed in pure helium for 2 hr at 870°C; the resulting grain diameter was about 150 µ. Specimens 0.5 by 8 cm were cut from the foils and I7e55 was vapor deposited on one of their surfaces. A 38 gage alumel-chrome1 thermocouple was spot welded in the middle of one of the specimen long edges, Fig. 1. Two 38 gage chrome1 wires were also spot welded along the same edge on each side of the thermocouple; they were placed 2.5 cm apart and used for electrical resistance measurements. In order to prevent twisting and crumpling, the specimens were pinched between two quartz plates 0.1 by 1 by 7 cm and the assembly was close fitted into a 1 cm ID quartz tube. Four holes were drilled through the tube to let the 38 gage wires out: these were connected to the recording equipment by means of extension wires. 20-gage nickel wires fixed at both ends of the specimens were used to thermally cycle the foils by Joule heating. The above described device was placed in a 2.7 cm ID quartz tube which in turn was placed in a tubular furnace. Either a pure helium atmosphere or circulating hydrogen was used during the experiments. Specimens were subjected to thermal cycles between a minimum temperature To and a maximum temperature Tm at rates ranging from 1 to 6 cpm. This was obtained by maintaining the furnace at a constant temperature near the minimum temperature To and periodically passing an electric current through the specimen. Cooling was achieved by heat losses to the surroundings. The forms and periods of cycles were varied from one specimen to another; however, each specimen was subjected to one type of cycle only. The temperature and electrical resistance variations of the specimens were recorded as a function of time. The temperature curves were used for diffusion calculations while the electrical resistance curves were used to monitor the transformation and to determine its starting point and its approximate duration. Diffusion was measured by the method developed by Kryukov and zhukhovitskii3 and modified by Angers and Claisse.4,5 In this method a metallic foil is coated on one side with a radioactive isotope and the activity is measured periodically on both sides during the diffusion anneal. The following equation then holds: where: I1 Activity on the surface on which the deposit is made. I, Activity on the opposite surface. t Diffusion time. B Constant. D Diffusion coefficient. d Foil thickness including the deposit. G(t) A function of time; it is a second order correction term which is given graphically in Refs. 4 and 5. The diffusion coefficient D is found by plotting ln[(Il - I2)/(I1 + I,)] -G(t) against t; the resulting slope m leads to an accurate calculation of D through Eq. [2]. The effect of the a-r transformation on diffusion is expressed by the ratio DT/DU where:

Jan 1, 1970

By R. W. Regehr, R. A. Burmeister

Epitaxial growth of GaAs 1-xPx on germanium substrates was achieved using an open tube vapor transport system. The compositional range of 0.3 < x < 0.4 was examined. The best results were obtained with (311) orientation of the germanium substrate. The physical and chemical properties of the resulting layers were investigated using several techniques. Spectrographic analyses of the layers indicate substantial incorporation of germanium into the GaAs t-X Px layer. Evidence is presented which indicates that this incorporation occurs via a vapor phase transport process rather than by solid phase dijfu-sion. Electrical measurements suggest that the germanium thus incorporated behaves predominantly as a deep donor in the compositional range of 0.33 < x * 0.40 and has a deleterious effect upon the luminescent properties of GaAs1-x Px. The increasing technological importance of GaAs1-xPx for use in light-emitting devices has led to an evaluation of several aspects of existing growth processes. The method most commonly used to prepare GaAs1-xPx for electroluminescent device applications is vapor phase epitaxial growth on GaAs substrates.&apos;-4 In a typical electroluminescent diode structure the active region of the diode is entirely within the epitaxial layer and thus the electrical properties of the substrate are relatively unimportant since it is effectively a simple series resistance (assuming hetero-junction effects to be negligible). The use of germanium rather than GaAs as the substrate material is of interest for several reasons. First, GaAs of reasonable structural quality has been epitaxially grown on germanium4-2 and it is reasonable to expect that GaAs1-xPx could subsequently be deposited on the GaAs layer. Second, germanium substrates are readily available with both lower dislocation densities and larger areas than GaAs. Finally, single crystals of germanium are more economical than GaAs single crystals. The principal objective of the present investigation was to test the feasibility of growing GaAs1-xPx epi-taxially on germanium substrates, and to evaluate the properties of such layers with regard to electroluminescent device requirements. The approach used was to a) demonstrate epitaxial growth of GaAs1-xPx on germanium, and b) characterize the relevant structural, electrical, and optical properties of the GaAs1-xPx layers. The possibility of germanium incorporation into the grown layers was of special interest since there was some indication of this in previous studies of GaAs growth on germanium.5&apos;11,12 Although a study of the electrical properties of germanium in GaAs1-xPx was not an intent of this investigation, several features of the electrical properties of the layers grown in the present study which appear to be due to germanium are described. EXPERIMENTAL PROCEDURE The open-tube vapor transport system used for the epitaxial growth of GaAs1-xPx is illustrated in Fig. 1. This system utilizes the GaC1-GaC13 transport reaction and is similar in most respects to the larger system described elsewhere.&apos; The germanium substrates were n-type, with a resistivity of 40 ohm-cm (Eagle-Picher Co.). These were cut to the orientations of {100), {111), and (3111, and were mechanically polished and chemically etched in CP-4 (5 min at 0°C) prior to growth. In some cases, a GaAs substrate was employed in addition to the germanium. The orientation of the latter was {loo}, and they were also mechanically polished and chemically etched prior to growth. The initial composition of the deposited layer was pure GaAs. After approximately 10 microns of GaAs was deposited on the germanium substrate, the phosphorus content of the layer was gradually increased over a distance of approximately 15 microns to the desired concentration and maintained at this value throughout the remainder of the growth. Typical operating parameters used during growth are given in Table I. Selenium was used as a n-type dopant in several runs to facilitate comparison of the electrical properties of the layers grown on germanium with those of layers grown on GaAs substrates, which are usually doped with selenium. The concentration of H2Se in the gas phase was adjusted to a value which would normally yield a carrier density of 1 to 5 x 101 7 at room temperature in layers grown on GaAs substrates. The terminal surfaces of the epitaxial layers were examined by optical microscopy for structural characteristics. Laue back-reflection photographs (Cu radi-ation) were also made on the terminal surface to verify the epitaxial nature of the deposit. After these steps

Jan 1, 1970

By N. S. Stoloff, R. G. Davies

A study has been made of the efject oj different dislocation-precipitate interactions upon the temperature dependence of the flow stress of aged Ni-14 at. pct A1 alloy. It is observed that when the dislocations bow between widely spaced (-20004 coherent Ni3Al particles the flow stress decreases with increasing temperature in the normal way. However, when the dislocations cut closely spaced (-5004 particles the flow stress is independent of temperature from -100 to 600°C, due to a balance between softening of the matrix and an increase in strength of the particles with increasing temperature. The retention of strength at high tempera-tures of commercial nickel-base alloys, which are strengthened by the precipitation of a phase based upon Ni3Al, is thought to be due to the unusual strength properties of Ni3Al. The flow stress of Ni3Al increases continuous1y from -196"C to a maximum at -600"C. It is concluded from a series of thermal-mechanical tests that the sevenfold increase in flow stress over this temperature interval is due to a lattice effect and is not diffusion-controlled. The flow stress of precipitation- or dispersion-hardened materials depends on the resistance to dislocation motion within the matrix and the extra energy required for dislocations to bow between or to cut particles. If the dislocations bow between the particles or if the strength of the cut particles is constant with temperature, then the flow stress of the precipitation-hardened alloy must decrease with increasing temperature due at least to the decrease in elastic modulus of the material. There will be softening also from thermally activated cross-slip or climb, offering an additional degree of freedom for dislocations to avoid particles. For example, in the case of nickel containing a dispersion of thoria,&apos; which most probably deforms by dislocations bowing between particles, the flow stress decreases by about 50 pct between 25" and 650°C. In A1-Cu alloys2 aged to produce the 8" precipitate, dislocations cut the particles, and the flow stress decreases by about 20 pct between -269" and 25°C. However, many commercial high-temperature nickel-base alloys, for example Inconel-X and Udimet-700, exhibit little or no decrease in flow stress with increasing temperature up to about 700°C. A characteristic feature of these alloys is that they are strengthened by the precipitation of a phase based upon Ni3A1. Guard and westbrook4 and flinn&apos; have shown that Ni3Al (and alloys in which a third element such as molybdenum or iron is substituted for part of the aluminum) is unusual in that the hardness and flow stress increase with temperature to a maximum at about 600°C. For the flow stress of a precipitation-hardened alloy to be independent of temperature we propose that the particles must be cut by dislocations moving through the matrix and that the strength of the particle must increase with increasing temperature. Theories of precipitation hardening do not take into account the flow stress of the dispersed particles that are cut during deformation; the only dissipative process usually considered7 is the creation of interface within the particle and between the precipitate and matrix. The purpose of the present investigation has been to study in detail the temperature dependence of the flow stress of a nickel-base alloy strengthened by the precipitation of Ni3Al in two structural conditions such that when deformation occurs it does so by dislocations a) bowing between the particles and b) cutting the particles, respectively. A simple binary Ni-14 at. pct A1 alloy was chosen because considerable information is already available for this system concerning phase equilibria and precipitation reactions and rates.&apos; Dislocation-precipitate interactions in the binary alloy should be similar to those in the more complex commercial alloys. In addition, the mechanical and physical properties of NisAl were studied in detail in the hope of elucidating the mechanism by which the strength increases with increasing temperature up to 600°C. EXPERIMENTAL PROCEDURE For the study of the effect of precipitation of Ni3A1 upon the temperature dependence of the flow stress, an alloy containing 14 at. pct A1 was utilized; a Ni-8 at. pct A1 solid-solution alloy was employed as a comparison material. Vacuum-cast ingots were hot-rolled at 1000°C and cylindrical compression samples, 0.20 in. diam by 0.40 in. high, were prepared from the 1/4-in.-diam rod. Specimens were recrystallized and solution-treated at 1000°C for 1/2 hr and then water-quenched. A preliminary study revealed that, when the Ni-14 at. pct A1 alloy was aged for 1 hr at 700°C, significant precipitation hardening was obtained, and that the structure was free from grain boundary discontinuous precipitation; an overaged condition was produced by annealing the aged specimens at 850°C for 1 hr. To circumvent the difficulties involved in the hot rolling and swaging of Ni3A1, compression samples,

Jan 1, 1965

By L. J. West, R. M. Perrry

This chapter describes the rock mechanics studies performed for a high cut at a nuclear power station in Pennsylvania. Two units presently are being constructed on the Susquehanna River. When these units are completed, they will generate approximately 2100 MW of electricity. It was necessary to excavate about 1 million cu yd of rock to prepare the site. This excavation resulted in a high cut on the west and north sides of the station area with a maximum height of about 200 ft. The location of the high cut with respect to the plant facilities is shown on Fig. 1. The recommended slope angles ranged from 1 ½ (horizontal) to 1 (vertical) for the upper residual soil to ½ to 1 for the deeper competent rock. Because of the significant height of this cut and the fact that the slope is immediately adjacent to the proposed nuclear facilities, extensive stability analyses were performed prior to, during, and after excavation to evaluate the steepest angle at which the slopes could be safely cut. The studies consisted of evaluating both qualitatively and quantitatively all apparent factors which could affect the stability of the slopes. These factors include the strength of the material, the zones of weak material which are present along the planes of schistosity, the prominent joint systems, the ground water, and postulated seismic effects. FIELD AND LABORATORY STUDIES A comprehensive program of field explorations was performed to evaluate the geologic characteristics of this site. This program consisted

Jan 1, 1970

By M. J. Ginsberg, N. A. Gokcen

THE preliminary study of electrochemical desul-furization performed by Ohtani and Gokcen1 left a number of points concerning the process to be investigated. Two of these were i) the determination of the effect of greater current and voltage on the desulfurizing Flower of acid slags (% CaO/% SiO2- 1) and ii) the possibility of the loss of silica in slag by the reactions 2C (in metal) + SiO2 (slag) = Si (in metal) + 2CO(g) and C + SiO2 (in slag) = SiO(g) + cO(g) proceeding to a point at which the composition of the slag was sufficiently altered toward the basic side so a1.s to noticeably affect the rate of de-sulfurization. The apparatus and the procedure used in the present investigation were the same as those used by Ohtani and Gokcen, except the control circuit was connected to 120 v dc instead of 24 v dc and thereby allowed greater freedom in choosing the values of both current and voltage. The graphite crucible containing the melt and serving as the cathode was 3-in. high, and was of 1 1/2-in. ID with a graphite bar of 3/8-in. diam and 8-in. length threaded into the bottom for electrical connection. This was placed into a magnesja outer crucible with a hole in the bottom and alumina insulation was packed between the two crucibles. A charge consisting of 180 g of

Jan 1, 1962

By F. A. Crossley

The additions: o, Sn, Zr, Cb, Mo, and V were studied for their effects on the a/a + Ti3A1 boundary of Ti-A1 base ternary alloys. These additions were chosen because of their importance to commercial titanium alloy practice—oxygen as the major impurity (in terms of influence on mechanical properties) and the others as major alloying additions. The composition and temperature ranges of investigation varied according to the system as shown in Table I. The principal means of investigation was light-microscopy. The basis of the ternary studies was the recently determined titanium-rich end of the Ti-A1 system.&apos; MATERIALS, METHODS, AND PROCEDURES Ingots were prepared in 15 g size for all alloys except those of the Ti-Al-Mo and Ti-A1-V systems which were prepared in 20 g size. These alloys were prepared from high-purity, electrolytically refined titanium obtained from the Bureau of Mines, Boulder City Metallurgical Laboratory, Boulder City, Col., and Chicago Development Corp., Riverdale, Md., for the 15 g and 20 g ingots, respectively. The alloying additions were obtained from commercial sources, and were at least of 99.9 pct purity, except the V-15 wt pct A1 master alloy for vanadium additions. This alloy was of 98.2 pct purity; the major impurities were 0.37 wt pct Fe and 0.38 wt pct Si. The ingots were prepared by multiple melting in a nonconsum-able-electrode arc furnace. The ingots were covered with Markal coating "CR-T22" (Markal Co., Chicago) to protect them from scaling. Markal coating is applied as a slurry of solids in a volatile carrier liquid. The coated article is air dried. Upon heating to the hot working temperature the coating fuses to form a glassy, protective film. The ingots were heated to 1000°C and rolled to 0.16 in. thickness, reheating after each pass. The glassy film was removed by sand blasting. Ten mils were removed from all surfaces by grinding and/or pickling (3 pct HF, 30 pct HN03, balance water). Grinding was always followed by pickling to remove traces of the grindmg medium. Hydrogen removal was accomplished by vacuum annealing at 1000°C for 2 hr to a final pressure of about 0.02 µ Hg. This was followed by annealing in evacuated Vycor bulbs (800°C, 2 hr, ice brine quenched (IBQ)) in order to maximize ductility. The materials were then lightly pickled and cold rolled to 0.12 in. thickness or cracking, whichever occurred first. After rolling, 1/2 by 1/4 in. specimens were cut for the equilibration anneals given in Table 11 and carried out as previously described.1 Final polishing of the specimens for metallographic examination was done by electrolytic means. Specimens were first examined without etching under bright field and polarized light illumination, for this is the only means of detecting the "two-phase" phenomenon.1,2 The term "two-phase syndrome" refers to Ti-A1 al-loys which appear on the bases of their chemical, phys-ical, and mechanical properties, to be two-phase, but are actually single phase and inhomogeneous in composition. Since processing and heat treatment of the alloys of the first group were completed before the two-phase syndrome was discovered, a number of the specimens were found to exhibit this phenomenon—80 pct of those of the Ti-Al-Zr system, 5 pct of those of the Ti-Al-Sn system, 30 pct of those of the Ti-Al-Zr system. The affected specimens were homogenized by heating above the ß transus temperature and quenching. The heat treatment and working schedules to accomplish this are given in Table 111. After rolling, specimens were pickled (3 pctHF, 30 pct HNO3 in water) to remove 1 to 2 mils from the

Jan 1, 1970

By Adam L. Wesner, A. C. Richardson

This paper describes the development of a continuous float-and-sink process to produce coal low enough in ash content to be suitable for production of electrodes. The cleaned coal had a combined iron and silicon content of 0.239 pct. The efficiency of recovery was 84 pct. DURING World War I1 the demand for electrode carbon was greater than could be met by the supply of petroleum coke available for this use. It was believed that coke made from an extremely low-ash coal might be a suitable substitute for petroleum coke. Requirements for electrode carbon to be used for the production of aluminum are that the silicon plus iron content shall be not more than 0.14 pct of the coke. However, during the period when petroleum coke was in short supply, it appeared that relaxations of the specifications might be allowed to permit 0.4 pct iron plus silicon in the coke. For this work, the specifications were that the coal should contain less than 1 pct of ash, and the combined iron and silicon content of the coal should not exceed 0.28 pct. Heavy-liquid separations made on a number of coals showed that if certain size fractions of some coals Were separated at low specific gravities the resulting float products would meet the required specifications. The objective of this work was to develop a continuous, commercially feasible process for producing low-ash coal. After consideration of various processes, the method chosen was a float-and-sink separation using a solution of calcium chloride as the separating medium. Eagle Seam coal was used for the experiments. The —10 +35 mesh fraction was found to be the most promising feed for producing the low-ash content coal. A batch of 30 tons of — --in. coal was screened at 10 and 35 mesh; the yield of —10 +35 mesh was 20 pct of the feed. This fraction comprised the feed for the separation tests. In spite of the fact that this portion was screened a second time at 35 mesh, the coal still contained 16 pct that was finer than 35 mesh. Three-fourths of the undersize was in the —35 +48 mesh range. A representative portion of the —10 +35 mesh fraction was subjected to batch float-and-sink separations to determine the best gravity to be used in the continuous tests to obtain a high recovery of low-ash content coal. The heavy liquid used was a mixture of carbon tetrachloride and benzene which assured complete wetting of all of the particles. As usual in batch separations, adequate time was allowed for each separation so that even the near gravity particles had ample time to separate. The separations were made at increments of 0.01 sp gr from 1.25 to 1.28 and also at 1.32 and 1.59. Each specific-gravity increment was assayed for ash content. From these data it was concluded that 1.27 sp gr was best for the continuous separation of the coal. The products from the batch separation were composited into float 1.27 and sink 1.27 sp-gr fractions; these were assayed for ash, iron, and silicon. Table I shows the results of the batch separations. The composite float 1.27 fraction contained 66.04 pct of the total weight, and had an analysis of 0.79 pct ash, 0.073 pct iron, and 0.112 pct silicon, or 0.185 pct iron and silicon combined. These data are indicative of the results possible if a perfect separation is made at 1.27 sp gr under static conditions. Inasmuch as the method under investigation is a dynamic system these results could not be obtained. It remained to be determined, however, just how close to the theoretical results the actual continuous separation would be.

Jan 1, 1953

By Adam L. Wesner, A. C. Richardson

This paper describes the development of a continuous float-and-sink process to produce coal low enough in ash content to be suitable for production of electrodes. The cleaned coal had a combined iron and silicon content of 0.239 pct. The efficiency of recovery was 84 pct. DURING World War I1 the demand for electrode carbon was greater than could be met by the supply of petroleum coke available for this use. It was believed that coke made from an extremely low-ash coal might be a suitable substitute for petroleum coke. Requirements for electrode carbon to be used for the production of aluminum are that the silicon plus iron content shall be not more than 0.14 pct of the coke. However, during the period when petroleum coke was in short supply, it appeared that relaxations of the specifications might be allowed to permit 0.4 pct iron plus silicon in the coke. For this work, the specifications were that the coal should contain less than 1 pct of ash, and the combined iron and silicon content of the coal should not exceed 0.28 pct. Heavy-liquid separations made on a number of coals showed that if certain size fractions of some coals Were separated at low specific gravities the resulting float products would meet the required specifications. The objective of this work was to develop a continuous, commercially feasible process for producing low-ash coal. After consideration of various processes, the method chosen was a float-and-sink separation using a solution of calcium chloride as the separating medium. Eagle Seam coal was used for the experiments. The —10 +35 mesh fraction was found to be the most promising feed for producing the low-ash content coal. A batch of 30 tons of — --in. coal was screened at 10 and 35 mesh; the yield of —10 +35 mesh was 20 pct of the feed. This fraction comprised the feed for the separation tests. In spite of the fact that this portion was screened a second time at 35 mesh, the coal still contained 16 pct that was finer than 35 mesh. Three-fourths of the undersize was in the —35 +48 mesh range. A representative portion of the —10 +35 mesh fraction was subjected to batch float-and-sink separations to determine the best gravity to be used in the continuous tests to obtain a high recovery of low-ash content coal. The heavy liquid used was a mixture of carbon tetrachloride and benzene which assured complete wetting of all of the particles. As usual in batch separations, adequate time was allowed for each separation so that even the near gravity particles had ample time to separate. The separations were made at increments of 0.01 sp gr from 1.25 to 1.28 and also at 1.32 and 1.59. Each specific-gravity increment was assayed for ash content. From these data it was concluded that 1.27 sp gr was best for the continuous separation of the coal. The products from the batch separation were composited into float 1.27 and sink 1.27 sp-gr fractions; these were assayed for ash, iron, and silicon. Table I shows the results of the batch separations. The composite float 1.27 fraction contained 66.04 pct of the total weight, and had an analysis of 0.79 pct ash, 0.073 pct iron, and 0.112 pct silicon, or 0.185 pct iron and silicon combined. These data are indicative of the results possible if a perfect separation is made at 1.27 sp gr under static conditions. Inasmuch as the method under investigation is a dynamic system these results could not be obtained. It remained to be determined, however, just how close to the theoretical results the actual continuous separation would be.

Jan 1, 1953

By N. A. D. Parlee, I. D. Shah

THIS communication reports the results of some work done on the effect of gold, palladium, and platinum on the liquid-gas-solid equilibrium in the Ag-O system,1,2 see Fig. 1. Recently several investigators3, 4, 5 have reported the effects of gold, palladium, platinum, and copper on the solubility of oxygen in liquid silver. This communication represents only a portion of the work done here on the solubility of oxygen in liquid silver and liquid Ag-Au, Ag-Pd, and Ag-Pt alloyss—the greater part having already been reprted. The apparatus, materials, and procedures used were similar to those of earlier work.&apos; l The main precautions observed in obtaining these freezing points at constant temperature and PO2 = 1 atm were as follows: 1) The points were approached very slowly from higher temperatures. 2) In the very near vicinity of the L-G-S equilibrium point precautions were taken to see that the melt was in equilibrium with oxygen at one atm. Equilibrium was considered to have been attained when no more absorption of oxygen was observed in the last 15 min at a fixed temperature. 3) In the case of these alloys, the freezing point of the melt at 1 atm of oxygen and the equilibrium amount of oxygen absorbed by the liquid "infinitesimally" above this point were determined by lowering the temperature in very, very small steps, equilibrating at

Jan 1, 1969

By E. Miller, K. Komarek, W. Johnson

The activity of aluminum in solid Cr-A1 alloys has been measured by an isopiestic technique between Cr-A1890&apos; and 1126" and 13 and 80 at. pct Al. The integral free energy of mixing has a minimum value of —5600 cal per g-atom at 59 at. pct Al. The maximum solid solubility of aluminum in chromium was determined to be 43 at. pct Al, and the composition limits of the compounds CrA14, Cr4A19, and Cr5Al, at 1000"~ were found to be 79 to 80, 66 to 70, and 59 to 63 at. pct Al, respectively. The thermodynamic properties of the Cr-A1 system have been investigated as part of a thermodynamic study of aluminum-transition metal systems.172 Little information is available on the equilibrium properties of the Cr-A1 system. The heats of formation of solid Cr-A1 alloys have been determined by Kubaschewski and Haymer at 600" and low-temperature specific heat data have also been obtained.~ More extensive work has been performed on the phase diagram, and a compilation has been provided by Hansen and Anderko,~ their phase diagram at elevated temperatures being essentially based on the work of Bradley and LU.~ The high-temperature portion of the phase diagram shows an intermediate phase CrA14 decomposing peritectically at 1018°C and existing at 82 at. pct A1 at 1000°C. They also identified the compounds with solubility limits of 72 to 75 at. pct A1 at 1000°C, and Cr5A1,, existing at 61 at. pct A1 at 1000°C. The maximum solid solubility of aluminum in chromium at 1000°C was found to be 46 at. pct Al. These elevated-temperature data were obtained by examination of quenched samples and were considered as less precise than the lower-temperature data. Koester, Wachtel, and Grube7 have revised the phase diagram as a result of their magnetic susceptibility and X-ray study. The results of this work differ appreciably from those of Bradley and Lu at temperatures above 800°C. The CrA1, compound is given as existing between 79 and 81 at. pct A1 at 1000°C, and they do not indicate the presence of a CrA13 phase reported by Bradley and Lu. They also report the compound Cr4Alg as having solubility limits of 66 to 70 at. pct A1 at 1000°C, while Bradley and Lu show this compound stable only up to 870°C. Koester et al. state that the high-temperature modification of the compound Cr5A18 is stable down to 1125"C, and not 980°C as stated by Bradley and Lu, and that the low-temperature modification of Cr5Al, has a range of homogeneity of 58 to 63 at. pct A1 at 1000°C. They also report that the maximum solid solubility of aluminum in chromium is 43 at. pct A1 at 1000°C. APPARATUS AND EXPERIMENTAL PROCEDURE An isopiestic method was employed which has been successfully applied to the determination of aluminum activities in solid ~e-All and Ni-Al alloys. Alloy specimens were held at different positions in a temperature gradient and were equilibrated with aluminum vapor from an aluminum reservoir kept at the temperature minimum of an impressed thermal gradient in a closed alumina system. Diffusion of aluminum into the specimens occurred until equilibrium was reached, at which the partial pressure of aluminum in each of the specimens was given by the vapor pressure of the pure aluminum reservoir. The activity of aluminum referred to liquid aluminum as the standard state in a given equilibrated sample at temperature T could therefore be expressed by: vapor pressure of pure aluminum at _ the temperature of the reservoir Vapor pressure of pure liquid aluminum, at specimen temperature T Since both the temperature of the aluminum reservoir and the specimen temperatures were determined experimentally, and the vapor pressure of pure aluminum is known as a function of temperature,&apos; the activity of aluminum in a given aluminum alloy of known composition could be calculated. Initial runs were made with samples consisting of pure chromium chips placed in alumina crucibles. These runs exhibited large inconsistencies, indicating that equilibrium was not attained. High aluminum content Cr-A1 alloy powders were therefore substituted for the pure chromium specimens. The starting composition of the alloys was adjusted through experimentation until the concentration change necessary to attain equilibrium was small. In this manner, consistent results were obtained in reasonable times. SPECIMEN PREPARATION Alloy specimens were prepared from chromium of 99.997 pct minimum metallic purity: with 0.028 to 0.038 pct H, 0.0002 pct N, and 0.27 to 0.46 pct 0 (Aviquipo, Inc.). The aluminum had a purity of 99.99+ pct and the following impurities: 0.003 pct Cu; 0.002 pct S; 0.002 pct Fe; 0.001 pct Pb; 0.001 pct Ga (Aluminum Corp. of America). Alloy powders were prepared from weighed mixtures of chromium and aluminum by double-arc melt-

Jan 1, 1969

The Johns Hopkins Press, Johns Hopkins University, Baltimore, Md The Johns Hopkins Press has issued a number of books as The Johns Hopkins University Studies in Geology Five of the studies are paleontological in character; five are on geology: No. 1, The geology of the Corocoro copper district of Bolivia, by J. T Singewald, Jr and E W. Berry, $1 50, 2, The geology and paleontology of the Huancavehca mercury district, by E W Berry and J T Singewald, Jr $1 50, 6, Contributions to the geology and paleontology of South America, by E W. Berry and F M Swartz, 3175, 7, The geology of the Island of Trinidad, B W I, by G A Waring, with notes on the paleontology by G. D Harris, $1 75, 8, Fifty years&apos; progress in geology, 1876-1926 Papers presented at the Geological Conference during the 50th Anniversary of the Johns Hopkins University, $1 50 An additional publication on geology is. Notes on the minerals occurring in the neighborhood of Baltimore, by G H Williams, 25 cents. In the list of Doctors&apos; Dissertations available from the University are found all theses on geology and mineralogy, about 90 in number, from 1886 on Authors of many of these have since made great names for themselves in the fields of geology and mineralogy. Most of the theses have been published as papers by other agencies and, as such, will be found under other headings in this directory

Jan 1, 1933

1. What Effect Has Sulfur Or Vanadium (In The Oil) On The Steel With Your Burner? 2. Also, what is the decibel rating on the floor when your burner is on? AUTHORS&apos; REPLY 1. There is no effect. 2. The decibel rating is 98-99 decibels.

Jan 1, 1972

Suggestions for Directorial representatives should be submitted by the District Committees between November 1 of the year indicated and the following Annual Meeting District 1 New York Section (Each Year) District 2 Boston (1950) Pennsylvania Anthracite (1951) Lehigh Valley (1952) Philadelphia (1953) Connecticut (1954) Adirondack (1955)

Jan 1, 1952

By R. G. Ward, John Henderson

It has been shown1 that the observed density1-&apos; of liquid iron silicates in contact with solid iron depends upon whether nitrogen or argon is used to protect the experimental system from oxidation. These densities have been measured by the maximum bubble-pressure method, in five different labora-

Jan 1, 1965

By P Shenon

THE Elk City district is in north-central Idaho about 60 miles east of Grangeville and near the headwaters of the South Fork of the Clearwater River (Fig. 1). At the height of its boom in the early sixties, Elk City had a population of more than 2000 people.1 Published estimates of the placer production from the district range from $10,000,000 to $18,500,000. Although the first quartz-vein location was made as early as 1870, very little gold was extracted from quartz ores until after the completion of the American Eagle mill in 1902. Between 1902 and 1932 a total of from $750,000 to $1,000,000 was taken from about six properties.

Jan 1, 1934

By W. R. Webster

SINCE the delivery of our paper on Some Comparative Properties of Tough-pitch and Phosphorized Copper,1 a new brand known as "oxygen-free high-conductivity copper" (brand OFHC) has become available to consumers. It was thought desirable to make a comparison between the properties of this material and those of the materials covered by our original paper and its discussion. FIG. 1.-CHARACTERISTIC ANNEALING CURVES OF VARIOUS TYPES OF COPPER. Preliminary tests had indicated some notable differences. A billet of oxygen-free high-conductivity copper was taken from regular production. A chemical analysis of the particular billet was not made, but the producer of the material has given as typical the analysis shown in Table 1. The

Jan 1, 1933