Search Documents

By Herbert A. Everest

The idea of economical production is usually associated with large operations, tonnages, and mines, with even larger capital behind them. , Nevertheless many small mines operate in the shadow of large competitors and make a good showing on the capital invested despite larger overhead expenses. For the purpose of this discussion I will divide the cost of production into classes, and specify opposite each the approximate percentagc expended thereon: 1. Labor, including miners and company men; 60 to 75 per cent. 2. Development, including all necessary .yardage, room turning, crosscuts, etc.; 7 to 12 per cent. 3. Deadwork, covering payment to miners for handling falls, draw-slate, or faults, rock work, water, and in general, all nonproductive labor; 3 to 7 per cent. 4. Supplies: mine timbers, oil, brattice material, lumber, cement, and repairs to equipment; 2 to 6 per cent. 5. Expense: management, selling, office, taxes, etc.; 1 to 5 per cent. 6. Depreciation of coal reserves and royalties; 6 to 10 per cent. 7. Depreciation of equipment and interest on capital invested; 1 to 3 per cent. 8. Fuel; ½ to 1½ per cent. The labor cost for a small mine is relatively much lower than for a large mine, particularly the sum paid to company men. Idle-pay expense is cut to a minimum; the labor item being larger than all the others together, a saving in labor makes a decided showing on the total cost. The development charges in small and large mines are about the same. There should be a small showing on the deadwork item in favor of the small mine. The unit cost for supplies is usually small in the small mine. The operator of the small mine finds, owing to a limited tonnage, that the expenses of management, selling, etc., are abnormally high. The item, depreciation of coal reserves and royalties, is usually about

Jan 1, 1916

By P. A. Toynbee, D. G. Wilson

The combustion performance of sub-bituminous slack coal is greatly improved by the removal of the smaller size fractions. Screening processes are not well suited to the size separation, at 1/8 in. or 1/16 in., with coals which are normally wet, and the use of an alternative size-separation device has been investigated. It is felt that this classifier might be applied equally well to other minerals in cases such as this, where precise size limits are not essential. Coal is dropped as a curtain onto a curved metal plate, shaped rather like a ski-jump. The smaller particles, slowed up in their free fall to the plate and also by contact with the metal, leave the plate with a lower horizontal velocity; they can be separated from the larger particles by virtue of their shorter trajectory. The principle of the classifier is obvious from the diagram (see Fig. 1) which shows also the positions, relative to the curved plate, of the point of coal feed and of the dividing plate which separates the streams of coal particles. The horizontal distance between the curved plate and the dividing plate is varied in the tests. It is designated in the general case, by X. Tests were carried out using slack coal with a free moisture content higher than that expected in any commercial operation. The results given in Table I. show the percentage recovery of upgraded product, and the cumulative screen analysis of both the upgraded and reject material, for three different positions of the dividing plate. The results show, for example, that the original coal can be upgraded, with a recovery of 80%, to reduce the minus 1/8 in. frac-

Jan 1, 1965

By Robert E. Hochscheid

The subject article appears in the February, 1978, edition of Mining Engineering, and on page 190 carries the statement, "As most operators know, in a Water-Only cyclone, ability to adjust the vortex finder is quite important due to the sensitivity of this type of operations to variance in feed conditions and having to take them apart to make this adjustment is always a nuisance." Our experience as a manufacturer and supplier of Water Only cyclones does not agree with the above statement, and we offer the following brief discussion. Our company finds that the sensitivity of the Water-Only cyclone is a function of the fineness of the coal being washed, with the sensitivity to vortex finder length being greatest for coals coarser than 3/4-in. and virtually insensitive to raw coal finer than 1 mm. For coals finer than 1 mm, we find that we can use the shortest standard vortex finder in either our 10- or 15- in. Water Only cyclone without exception. For coals 5/8-in. x 1 mm ceramic vortex finders of fixed length have been satisfactory in all cases following an initial testing period in which the length was determined. Coals coarser that 5/8-in. are more sensitive to the vortex finder length, and two installations handling coals coarser than 1-in. continued to experiment with vortex finders of various lengths long after the initial startup period. For coals of all sizes, final adjustment of product quality has been achieved by determining the optimum size of apex orifice, which is accessible and readily changed, if necessary. Comments above assume no unusual change in the coal being washed or the required quality of clean coal.

Jan 1, 1979

ARTHUR PHILLIPS,* Bridgeport, Conn. (written discussion?).-It is to, be regretted that the very valuable paper by Messrs. Bassett and Davis did not appear in the early war period. The data presented would have been of inestimable service to inspectors, of cartridge brass who, admittedly, had little or no knowledge regarding the relation of grain size to temperature of anneal, and no real appreciation of, the significance of the Brinell hardness test. The paper is of considerable interest to, metallurgists also. WALTER R. HIBBARD, ? Bridgeport. Conn. (written discussion§).-The writer has carefully studied Messrs. Bassett and Davis's paper with considerable interest, inasmuch as our laboratory has tested cartridge brass by means of a Brinell machine. In March, 1917, at the suggestion of the Technical Department of the American Brass Co., we started a comparison of grain-size measurements and Brinell hardness of-cartridge brass with a gage of 0.1 in. or greater. This was continued until March, 1918, when we adopted the Brinell hardness test as standard for brass 0.1 in. gage or greater, and discontinued grain-size measurements upon this metal. The data collected during the test showed that the Brinell hardness indicated more accurately how the metal acted in actual working operations. It was also more reliable because two manipulators check themselves closer by the Brinell test than by the grain-size measurements. It also consumed less time in making the tests. Alfred V. de Forest, formerly assistant research engineer of our laboratories, has described the apparatus and some of the checking results in a paper read June, 1918, before the American Society for Testing Materials.1 The writer hopes that a more satisfactory. method for testing cartridge brass and gilding in gages thinner than 0.1 in. may be devised than the present method of grain-size measurements.

Jan 3, 1919

By Leonard Obert

Before 1957 a number of investigators reported stress determinations made on or near the surface of underground excavations. The usual procedure was to measure surface strains and to calculate the stresses using laboratory-determined values of the elastic constants of the rock. In some instances strain gages were stress-relieved so that the measured stress was absolute. Also, several investigators reported near-surface absolute stress determinations made by the flat-jack procedure. In 1958, Hast1 described a procedure for making absolute stress determinations within a body of rock. In this procedure a diametral deformation gage was placed in a borehole and then the borehole was overcored to produce stress relief. The secondary principal stresses in the plane normal to the axis of the borehole were calculated from measured deformations and the elastic constants of the rock. During the past nine years a number of investigations have been reported1-20 in which this technique, or modifications of it, have been reported. Both the stress distribution in the walls of underground openings and the stress field at points as great as 200 ft from these openings have been determined. Considered collectively, these reports shed some light on the nature of the stress distributions in the proximity of underground openings and on the stress field, that is, the state of stress outside of the zone of influence created by openings. To summarize these findings first consider the stress distribution in the wall and structural components of openings. Fig. 1 (a) shows a typical theoretical stress distribution curve in a linear-elastic, isotropic, homogeneous material. Fig. 1 (b) is an idealized measured stress distribution curve for the same opening in a relatively unfractured uniform, but brittle,

Jan 1, 1967

By L. M. Howe, J. Gordon Parr, E. Saarema

THE decreasing solid solubility limit at the titanium-rich end of the Ti-Cu constitutional diagram,' Fig. 1, suggests the possibility that titanium-rich alloys may be age-hardenable. However, results obtained by Holden et al. reproduced in Fig. 2 show that after quenching from 790°C the age-hardening of an alloy containing 1.7 pet Cu is very slight, while a 0.8 pet alloy decreases in hardness, during heat treatment at 400°C. It was believed possible that powder samples of alloys might show different results from the lump samples used by Holden et al., since small particles are often more sensitive to diffusion processes than larger samples. Consequently, a 1.9 pet (by weight) Cu alloy was made by the technique of levitation melting," checked for homogeneity, and filings of 48-65 Tyler screen size were cut from it for aging experiments. The filings were helium-quenched (by a technique described previously)' from 790°C, sealed in vacuo in silica tubes and aged at temperatures of 400°, 450°, and 500°C. Microscopic and X-ray examinations failed to reveal any structural changes during the aging process. This is not too surprising since early stages of precipitation do not usually manifest themselves in ways that are readily detectable by metallographic methods, and the extent of precipitation on overaging a 1.9 pet alloy is very small. However, hardness readings (taken on a Bergs-man micro hardness tester, using a 25 g load applied to a diamond indenter) do show a hardness peak at each aging temperature, Fig. 3. About a dozen readings were taken on each heat treated sample; the highest reading and the lowest reading were ignored and an average taken of the remaining values. In

Jan 1, 1957

By William E. Hubbard

The production of the Texas Panhandle1 up to Jan. 1, 1932, was slightly under 179,000,000 bbl., 90 per cent of which came from Hutchin-son and Gray counties. About 21,500,000 bbl. were produced during 1931. This was about 35 per cent less than the 1930 production and the smallest annual production since the first boom started seven years ago. The present daily production is slightly under 55,000 bbl., which is the production permitted under statewide curtailment. The assumed potential for the purpose of curtailment is 108,708 bbl. and the actual capacity of the wells is probably in the neighborhood of 75,000 barrels. The total initial production of the oil wells completed in 1931 was 40,714 bbl. from 117 wells or 347 bbl. per well as compared to a 511-bbl. average from the 304 oil wells drilled during the preceding year. Gray County led with 71 completions and a total initial production of 29,209 barrels. Completions Two hundred wells were completed in the Panhandle in 1931, as against 526 in 1930. Of the year's completions, 117 were oil wells, 77 produced gas, and but six were dry holes. Of the 3197 wells drilled in the Panhandle to date, 2944 have produced oil, gas, or both, making the ratio of dry holes to producers about 1:11.7. Ignoring the 64 dry holes drilled in nonproductive counties the ratio becomes 190:2944 or 1:15.5, which is somewhat more favorable than that obtained at the end of 1930. Of the oil wells completed 374 have been plugged. Although it is but five years since the peak of drilling operations more than one-fifth of the oil wells in Hutchinson County have been plugged. The percentage of total wells plugged to total completed oil wells, by counties,

Jan 1, 1932

By J. A. Ede

The object of the writer is to call attention to a rather unique aggregation of economic products distributed over a line of succeeding formations about 3 mi. long, to be seen within a few miles of La Salle, Ill. Fig. 1 is an ideal section of the stratification exposed and exploited along a distance of 3 1/5 mi. in a southwesterly direction from the quarry of the Utica Hydraulic Cement Co. located near the historic site of Kaskaskia village to the Oglesby shaft at Oglesby. No attempt has been made to cover the whole field, special mention only being made (with the exception of two places) of the operations found along the course or parallel to the direction assumed in the ideal section. I have used Fig. 2, after J. R. Bent and De Witt Kelly, to locate the relation of the La Salle anticline to the coal mines of this district and to show the operation of No. 1 and 3 mincs of the Illinois Zinc Co. Anticline and the Rock Formations Owing to the structural deformation between La Salle and Utica, the older rocks of the state are exposed to the surface along the northern embankment and the bottoms of the Illinois River valley near the latter place. At; the Illinois Zinc Co. works, Sec. 16, Tp. 33, R 1, a well for water mas sunk 1828 ft. and samples taken every 10 ft. of the ground penetrated; duplicates were sent to Mr. Cady of the Illinois Geological Survey. A general compilation or synopsis study of this section is here presented. As the well is over 1 mi. west of the Western limb of the anticline, the section affords some reliable data. These samples were studied and interpreted by H. M. DuBois as Lower Magnesian, and by G. H. Cady as the Lower Magnesian. The results are given in Fig. 3. The most interesting geological feature of this district is the La Salle anticline. In 1865, Leo les Quereux, looking at Split Rock, asked how it happened that the upper coal measures overlie strata of the Lower Silurian and what has become of the formations which are generally found intermediate—the Upper Silurian, the Devonian and sub-carboniferous, and the lower member of the coal measures?

Jan 1, 1920

By Richard E. Gray, Robert W. Bruhn

INTRODUCTION Underground coal mining has been practiced in the United States for over 200 years. Much early mining was not as efficient as today and unrecovered coal pillars, often of variable size and spacing, remain to support the overlying strata after mining has ceased. These conditions constitute a potential subsidence problem since the pillars will eventually fail. The possibility of subsidence above an abandoned mine must be anticipated except when total extraction has been achieved, permitting subsidence concurrent with mining, or when large coal pillars which have an adequate factor of safety for long-term support remain in the mine. Coal is found in 37 states and is mined under- ground in 22 states (HRB Singer, Inc. 1980). Underground mining produced 40 percent of the 7.5 x 10" kg. (830,000,000 tons) of U. S. coal mined in 1980 (Keystone, 1981). There are approximately 70,000 abandoned or inactive underground coal mines in the United States and approximately 2000 active underground coal mines (NAS/NAE, 1975). Underground coal mining in the United States will eventually extend beneath 162 x 109m2 (40 million acres). Thirty-two billion m2 (8 million acres) are already undermined (HRB Singer, 1977). Subsidence due to mining has affected more than 8 x 109m2 (2 million acres) in 30 states, 7.7 x 10 9m2 (1.9 million acres) from bituminous coal mining and the remainder primarily from anthracite mining (Johnson and Hiller, 1979). Subsidence from all other underground mines has affected only 6.9 x 10 7m2 (17,000 acres) (Johnson and Miller, 1979). Subsidence appears to be particularly widespread in two states, Pennsylvania and Illinois, although serious subsidence is found in localized areas of numerous other states (HRB- Singer, Inc. 1977). Host underground coal mining has occurred in the eastern United States, where the U. S. Bureau of Mines estimates 1.6 x 109m2 (398,600 acres) in urban areas in 18 states (out of a total 1.7 x 109m2 1418,400 acres]) are threatened by subsidence (Table 1) (Johnson and Miller, 1979). Pennsylvania and West Virginia contain 57 percent of the total threatened areas. The U.S. Bureau of Mines estimates the total cost to stabilize the estimated 1.7 x lo9m2 (418,400 acres) of subsidence prone urban land located above abandoned mines is over $12.5 billion (1978 costs).

Jan 1, 1982

By John Dasher, Wilfred L. Freyberger, James H. Pannell, A. M. Gaudin

WHEN beryllium is bombarded by gamma rays under suitable conditions it evolves neutrons. This nuclear reaction, Bes + y + n + Be", [I] is utilized in the process that is described in this paper. The equation, which physicists often abbreviate to Bevy, n)Be" shows that a photon, y, is absorbed by the Be- sotope of beryllium which then emits a neutron, n, leaving Be8 as a residue." It has been determined that the threshold for this reaction is 1.63 mev; that is, gamma rays having an energy less than 1.63 million electron volts do not have enough energy to remove a neutron from the beryllium nucleus. The threshold value for the beryllium (y, n) reaction is lower than that for any other element. The next most sensitive element is heavy hydrogen (deuterium) whose gamma neutron reaction, D2 (-y, n) H1, has a threshold of 2.2 mev. Thus, gamma rays having an intensity between 1.63 and 2.2 mev will evolve neutrons from beryllium and from beryllium only. Nuclear reactions can be considered as occurring between a projectile and a target. The probability of the occurrence of any such encounter can be expressed in terms of the "cross section" of the target nucleus for the projectile and projectile energy. This cross section, then, is the area normal to the path of the projectile controlled by the target for the purpose of the reaction under consideration. Cross sections are usually expressed in barns, in which a barn is lo-" sq cm. The cross section for Eq 1 is very small, even for nuclear reactions, and of the order of 10"3 barns. It is therefore necessary that a high flux of gamma radiation at the appropriate energy be used to obtain an appreciable neutron yield. In view of the nuclear properties of beryllium it seemed that if pieces of beryllium ore on a moving belt were bombarded with an intense beam of gamma rays, those pieces which are rich in beryllium minerals would emit neutrons at a sufficiently high rate to make it possible to detect that emission, and to use it to actuate a mechanical device for removal of the active from the barren particles. The principal economic source of beryllium is the mineral, beryl. Beryl occurs mainly in pegmatites which are characteristically coarse grained. The suitability of mechanical concentration depends upon the size at which the desired mineral can be liber-

Jan 1, 1951

By James H. Pannell, John Dasher, Wilfred L. Freyberger, A. M. Gaudin

WHEN beryllium is bombarded by gamma rays under suitable conditions it evolves neutrons. This nuclear reaction, Bes + y + n + Be", [I] is utilized in the process that is described in this paper. The equation, which physicists often abbreviate to Bevy, n)Be" shows that a photon, y, is absorbed by the Be- sotope of beryllium which then emits a neutron, n, leaving Be8 as a residue." It has been determined that the threshold for this reaction is 1.63 mev; that is, gamma rays having an energy less than 1.63 million electron volts do not have enough energy to remove a neutron from the beryllium nucleus. The threshold value for the beryllium (y, n) reaction is lower than that for any other element. The next most sensitive element is heavy hydrogen (deuterium) whose gamma neutron reaction, D2 (-y, n) H1, has a threshold of 2.2 mev. Thus, gamma rays having an intensity between 1.63 and 2.2 mev will evolve neutrons from beryllium and from beryllium only. Nuclear reactions can be considered as occurring between a projectile and a target. The probability of the occurrence of any such encounter can be expressed in terms of the "cross section" of the target nucleus for the projectile and projectile energy. This cross section, then, is the area normal to the path of the projectile controlled by the target for the purpose of the reaction under consideration. Cross sections are usually expressed in barns, in which a barn is lo-" sq cm. The cross section for Eq 1 is very small, even for nuclear reactions, and of the order of 10"3 barns. It is therefore necessary that a high flux of gamma radiation at the appropriate energy be used to obtain an appreciable neutron yield. In view of the nuclear properties of beryllium it seemed that if pieces of beryllium ore on a moving belt were bombarded with an intense beam of gamma rays, those pieces which are rich in beryllium minerals would emit neutrons at a sufficiently high rate to make it possible to detect that emission, and to use it to actuate a mechanical device for removal of the active from the barren particles. The principal economic source of beryllium is the mineral, beryl. Beryl occurs mainly in pegmatites which are characteristically coarse grained. The suitability of mechanical concentration depends upon the size at which the desired mineral can be liber-

Jan 1, 1951

By Martin T. Broome

INTRODUCTION The Luanshya Mine is situated in the southern part of the Zambian Copperbelt. The copper ore deposit is stratiform, and is preserved in a synclinorium known as the Roan/ Muliashi basin. Roan shaft (formally called No.14 shaft) is located at the eastern end of the syncline and is theoldest of the presently operating hoisting shafts, being sunk during the 1930's. It presently hoists some 45 per- cent of the total Luanshya Mine production. A cross-section through the shaft is shown in figure 1. The ore formation on the south limb is unmined on this section because until recently it was believed that such mining might cause damage to the shaft. This paper examines the influences of adjacent mining on this so-called 'shaft pillar', and describes the mechanics of subsidence of the pillar itself. GEOLOGY AND STRUCTURE Figure 1 shows the general form of folding in the vicinity of Roan shaft. The north and south limbs of the main syncline approach parallelism, with the bottom of the trough fairly smoothly rounded. The axis of the - trough plunges to the west-north-west at 6° - l0°. A brief summary of the major lithologies present in the Roan basin is given in table 1, however, the performance of the overall structure during progressive mining of the ore horizon is controlled by the following features in addition to the mining method. Intraformational Contacts These are characteristically weak in most geological environments. The BC/RL7 contact is an unconformity between moderately weak quartz-biotite schists below (unconfined compressive strength 40 - 80 MN/M 2), and strong quartzites above (U .C .S. 170-200 MN/M2) Subsequent formations are conformable, and planes of weakness are generally the result of contrasting lithology (see below). Weak Interbeds The Rt7, RL6, RL5, RL3 and RU2 horizons consist predominantly of quartzitic rocks, i.e. conglomerates, quartzites and argillites, and as such are generally strong and considered suitable for the positioning of development. Between these however, lie two much weaker dolomitic horizons, the RL4 and RU1. The Rt4 is the main hangingwall aquifer, and must be drained prior to mining. Drainage results in an extremely weak, blocky cavernous horizon which usually requires support if exposed by development. Similarly, the RU1 formation is comprised mainly of dolomites and dolomitic arqillites which are weak and cavernous. In the eastern part of the Roan/

Jan 1, 1981

By P. Duwez, L. Zwell

In recent years, the problem of pressing metal powder in a die has received much attention. The question has been the object of a Symposium held in New York in March 1947 under the sponsorship of the AIME; an excellent review of the subject may be found in Ref. 1. Various experimental techniques have been used to study the behavior of the powder in a die cavity. Two methods have been particularly successful; one consists of measuring the density distribution²,³ and the other makes use of a lead grid in the powder during pressing.4 In the present study, the pressure at various points on the bottom and the sides of a die 1.50 in. in diam was measured by means of small piston dynamometers and resistance sensitive strain gauges. In order to correlate the results with previous investigations, the pressure distribution inside the compact has also been determined by an indirect method based on density measurements. Strain Gauge Measurements of Pressure on Side and Bottom of Die A schematic drawing of the die used for measuring side pressures is shown in Fig 1. The pressure gauge consists of a 0.25-in. diam piston A which transmits the pressure to a dynamometer B, on which two Baldwin Southwark type 4-14 strain gauges are fastened 180" apart. Because the installation of several dynamometer assemblies along the side of the die would have been difficult, the pressure distribution was obtained in successive tests in which the distance from the gauge to the bottom of the compact was adjusted to different values by changing the length of the bottom piston. The dynamometer, disassembled from the die, was calibrated under compressive loads and showed a 1.00 ohm change of resistance for every 15,300 psi change of pressure (750 lb load change). All the strain gauge measurements were made with a null type Leeds and Northrup Wheatstone bridge. The sensitivity of the method was better than 1 pct and the accuracy was within 2 pct. These values were considered satisfactory in view of the rather large scatter in the measurements introduced by the random variation in packing the powder in the die. The stable ambient conditions and short time involved in the taking of observations made temperature compensation unnecessary-. The pressure distribution on the bot-

Jan 1, 1950

By Y. C. Liu, W. R. Hibbard

An aluminum single crystal cold-rolled from (110) [1121 essentially retains its initial orientation after 99.6 pct reduction in thickness. The orientation of the recrys-tallized grains of this material can be described in terms of crystallographic rotations about principal poles of deformation texture. DURING the study of the recrystallization of a copper single crystal cold-rolled from a (110) [112] initial orientation, the orientation of the re-crystallized grains could be derived by a 30" rotation of the orientation of the cold-rolled matrix about its <111> poles.&apos; The present investigation was undertaken to extend the work done on copper&apos; to an aluminum crystal also cold-rolled from a (110) [112] initial orientation. Experimental Procedure The procedure of this experiment was similar to that reported for copper.&apos; An aluminum (99.998 pct) single crystal rod* 1 % in. in diameter was grown in back-reflection technique.&apos; The specimen (1.20x 1.004x0.6787 in. thick) was then rolled along the [112] direction. The final thickness was 0.0028 in., giving a reduction in thickness of about 99.6 pet. Specimens were cut from the rolled strip with scissors, and approximately in. of disturbed metal was removed with Tucker&apos;s reagent. The rolling edge remained intact. The specimens were sandwiched between two graphite plates and annealed in a lead or lead alloy bath which was electrically heated. Pole figures were constructed using the techniques previously described.&apos; Specimens were electrolytically polished4 and etched with 47 pct HNO8, 50 pct HC1, and 3 pct of 48 pct HF. The electrolytic polishing method and etching reagent employed for aluminum specimens were not entirely satisfactory and the microstruc-tures could not be studied in any detail. Results and Discussion The octahedral pole figure of cold-rolled aluminum strip is plotted in Fig. 1. The <111> poles spread in the transverse direction approximately 8" for the highest intensity areas. The spread in the transverse direction can be related to a rotation about two <110> directions lying in a plane containing the rolling direction and rolling plane normal. The two <110> directions and a scale of rotation for the <111> poles are shown in Fig. 2. The amount of rotation is consistent for three of the four <111> poles, about 35" to 40". The discrepancy for the fourth pole is believed to be due to limitations of the film technique. Alternate inter-

Jan 1, 1956

By G. Sandoz, C. A. Siebert

OIL quenching of steel, in good commercial practice, is carried out using a great deal of agitation in the quenching bath. Many of the tests reported in the literature represent the results obtained on steels quenched into still oil. Scott1 describes three stages of cooling in liquid quenching baths, namely: "State `A&apos;-Vapor Blanket Cooling-In this, the first stage, a thin stable vapor film surrounds the hot metal. Cooling is by conduction and radiation through the gaseous film and is therefore relatively slow. "Stage `B&apos;-Vapor Transport Cooling- Termination of the `A&apos; stage is marked by wetting of the metal surface. Vapor forms copiously in bubbles and is carried away by gravity and convection currents to condense in cooler surrounding liquid. This is the fastest stage of cooling. "Stage `C&apos;-Liquid Cooling--The `B&apos; stage ends as the surface temperature of the metal approaches the boiling point of the quenching liquid. Vapor no longer forms, so cooling is by conduction and convection and the temperature difference is greatly decreased. This mode of cooling is slower than that of the `B&apos; stage." Mechanical agitation of the quenching medium will accelerate all three stages of cooling. The greatest effect, however, will be noted on stage `B&apos; because the removal of the bubbles from the surface of the steel will not be entirely dependent upon gravity and natural convection currents. The method employed in this investigation for evaluating the oils was the end quench test. The various oils were substituted for water as the quenching liquid and hardness determinations were made at various distances from the quenched end. Most of the tests were run using a 3/8-in. orifice with a 2 ½ -in. stream height. However, to check the effect of other velocities two additional conditions were used, namely: (I) A 3/8-in. orifice and 1-in. stream height, and (2) a ½ -in. orifice and a 3 ½ -in. stream height. In all cases the samples were suspended so that the quenched end was ½ -in. above the orifice. The steel used was an NE 9450 having the following analysis: [ ] Some tests were run on an NE 8740, 3312, and a 4340 steel. The results obtained on these steels confirmed those obtained on the NE 9450 and have therefore been omitted&apos; from this paper. The test bars were machined from 1 1/8 -in. stock to 1-in. diam by 4 in. long.

Jan 1, 1948

By George Watkin Evans

The need for mechanization in coal mining wherever it can be successfully introduced is evident when we take into account the fact that during recent years the coal-mine employee&apos;s wages have increased and his hours have been shortened. Coal is no longer King, and a brief study of statistics covering the production of coal, petroleum and natural gas and the development of water power will convince anyone that coal has had very powerful competitors during the past 10 years. Petroleum production in the United States between 1918 and 1936 increased from 100 per cent to 309 per cent. Water power increased from 100 per cent in 1918 to 270 per cent in 1936. Bituminous coal slipped from 100 per cent in 1918 to 75 per cent in 1936. The anthracite industry slipped from 100 per cent in 1918 to 50 per cent in 1932, but climbed to 55 per cent in 1936. In 1918, the State of Washington produced a little over four million tons of coal and the production of California oil, at that time, was a little less than one hundred million barrels per year. By 1929 the production of California oil had increased to a little over 292,000,000 bbl. or nearly 300 per cent as compared with 1918. By 1934 the production of coal in the state of Washington had dropped to about 1 1/3 millions of tons per year. Our neighbors in British Columbia had their coal production reduced from a little over 2 1/2 million tons in 1920 to less than 1 1/3 million in 1933. The North western Improvement Co., a subsidiary of the Northern Pacific Railroad Co., owns coal properties in various parts of Washington and Montana. The Northern Pacific is one of the very few railroads using any considerable quantity of coal in its operations. Practically all of the American railroads in the Pacific Northwest, except the Northern Pacific, are using cheap California fuel oil or electricity. This problem, of course, is not a new one in coal mining, and all of the progressive coal companies in the country have tried to meet competition from an overproduction of petroleum and an overproduction of natural gas as well as enlarged developments of hydroelectric plants.

Jan 1, 1938

By George Watkin Evans

The need for mechanization in coal mining wherever it can be successfully introduced is evident when we take into account the fact that during recent years the coal-mine employee&apos;s wages have increased and his hours have been shortened. Coal is no longer King, and a brief study of statistics covering the production of coal, petroleum and natural gas and the development of water power will convince anyone that coal has had very powerful competitors during the past 10 years. Petroleum production in the United States between 1918 and 1936 increased from 100 per cent to 309 per cent. Water power increased from 100 per cent in 1918 to 270 per cent in 1936. Bituminous coal slipped from 100 per cent in 1918 to 75 per cent in 1936. The anthracite industry slipped from 100 per cent in 1918 to 50 per cent in 1932, but climbed to 55 per cent in 1936. In 1918, the State of Washington produced a little over four million tons of coal and the production of California oil, at that time, was a little less than one hundred million barrels per year. By 1929 the production of California oil had increased to a little over 292,000,000 bbl. or nearly 300 per cent as compared with 1918. By 1934 the production of coal in the state of Washington had dropped to about 1 1/3 millions of tons per year. Our neighbors in British Columbia had their coal production reduced from a little over 2 1/2 million tons in 1920 to less than 1 1/3 million in 1933. The North western Improvement Co., a subsidiary of the Northern Pacific Railroad Co., owns coal properties in various parts of Washington and Montana. The Northern Pacific is one of the very few railroads using any considerable quantity of coal in its operations. Practically all of the American railroads in the Pacific Northwest, except the Northern Pacific, are using cheap California fuel oil or electricity. This problem, of course, is not a new one in coal mining, and all of the progressive coal companies in the country have tried to meet competition from an overproduction of petroleum and an overproduction of natural gas as well as enlarged developments of hydroelectric plants.

Jan 1, 1938

By Ernest Klepetko

A NOTABLE amount of fossil resin exists in many of the bituminous coal beds of Utah. The upper part of these show a marked concentration of resin, which occurs primarily in the fracture seams. In general, these seams are less than 1/8 in. thick, but it is not uncommon to find coal with areas as thick as 3/8inches. The resin is of the hard kauri variety, with coloration varying from deep blood red to lemon yellow and almost colorless. There is also an almost black variety, which is not readily soluble in the same solvents as the lighter colored resins. These resins are valuable for many industrial purposes. When refined, they are suitable for uses similar to those for which lac resins are usually employed. They are particularly desirable for preparing dielectric varnishes. They are also desirable in preparing printing inks, waterproofing agents, special synthetic rubbers and rubber cements. They are especially suitable as an admixture in synthetic rubbers and cements, as they supply the essential tackiness the synthetics lack. The following chemical trade characteristics have been found by Inter-Chemical Co. research chemists in the refined resins: [Specific gravity (melted) 1.03 -1. o6 Acid number6-8 Softening point, mercury method 160 -165°C Iodine value (Wijs)140-1.50 Refractive index1.544 Color (Hellige, 25 pct toluol) ...14 Molecular weight, average732 Purity, 99 + pct pure hydrocar Bon] "Unaffected by alkalies and resistant to one hour fusion with solid potassium hydroxide. Completely soluble in aliphatic and aromatic hydrocarbons. Insoluble in alcohols, ethyl acetate and other commonly used alcohols and esters. Compatible with natural and synthetic rubbers, chlorinated and cyclized rubbers, waxes, vegetable oils, mineral oils, rosin, ester gum, phenolic and modified phenolic resins and other natural and synthetic resins of like solvent solubility. The recovery and refining of these fossil resins has been the subject of much research work and has intrigued many investigators. Broadly speaking, the problem involves separation of the resin from the coal into a very high-grade concentrate, and subsequent treatment of this concentrate to produce an acceptable refined resin for its various usages. Obviously it is also desirable to recover the residual coal without excessive size degradation. The late W. D. Green, concentration engineer for Combined Metals Reduction Co., obtained U. S. Patent No. 1773997 for the recovery of resin from coal through

Jan 1, 1947

By D. F. Haley

THE molybdenite deposits at Climax, Cool., have recently attracted considerable notice, because of their great size, as compared with other known deposits of the same mineral. Climax station, on the. Colorado Southern narrow-gage railway, was at one time the Fremont Pass station on the Denver & Rio Grande. It is 1412 miles northeast of Leadville, and exactly on the divide between the headwaters of the Arkansas and Blue Rivers. Climax station is 11,300 ft. (3444 m.) above sea level. The working tunnel of the molybdenum mine is about 1 mile from the railroad, and 900 ft. above it, at an elevation of 12,200 feet. The climatic conditions are severe, and snow can be expected during any month of the year. Winter sets in not later than Nov. 1, the snowfall is very heavy, and the ground remains covered with snow until June 1, and sometimes even later. From June 1 to Oct. 1, there is much rain and a little snow falls in the late afternoon nearly every day. In October, 1917, there was one of the biggest snowstorms and blizzards of the year. Being just on the divide, constant strong winds blow the fine, dry snow with such force that, during most of the winter, outside work of any kind -is accomplished under most trying conditions. Within a few miles of Climax, some of the richest gold placers of Colorado occur. One of them, McNulty Gulch, was just across on the northeastern flank of Bartlett mountain. This mountain, therefore; was well prospected, and the presence of a bluish mineral and a yellowish one resembling sulphur was known to the old prospectors. They thought for many years that the blue mineral was graphite, and it is difficult to say when it first became definitely known that it was molybdenite. Claims had been staked as .early as 1896, but it is evident that the prospectors at that time were looking for gold. In 1902; several claims were acquired by H. Leal, who drove a tunnel about 900 ft. (274 in.) long, probably to intersect a fault, which shows on the surface, and was thought to be a possible gold carrier. Gold was not found in paying quantities, but throughout its length the tunnel passed through a fractured silicified granite, showing a fairly uniform distribution of a fine-grained bluish mineral, which was finally determined as molybdenite. For several

Jan 8, 1918

By W. A. Backofen, R. L. Fleischer

AN effect of orientation on the creep behavior of aluminum at 4.2 OK has been observed. Stress relaxation was measured in a hard-type tensile device after stopping the drive. From the spring constant of the device the load-time record could be converted to strain as a function of time. The strain sensitivity was 2-10-=, and the usual creep time of 1 min normally allowed a stress drop of about 25 g per sq mm. Further details of the apparatus and sample preparation appear elsewhere.&apos; It should be noted that neither stress nor strain were constant, so that quantitative comparison with current creep theories will not be made. Shear strain (y) as a function of time (t) was consistent with logarithmic behavior: y = A In t, where A is a constant. In some cases t was made as large as lo3 sec. In the results the quantity A divided by t (the resolved shear stress, which is the driving force for creep) is plotted as a function of strain prior to creep. The quantity A/t is thought to indicate qualitatively the ease with which dislocations can move during creep. In Fig. 1 are drawn tensile stress-strain curves and A/T-strain measurements for single crystals of three orientations: l(a) and l(b) for the maximum resolved shear-stress orientation, l(c) for an orientation 2 deg from [211], and l(d) for a [111] stress axis. The following observations were made: 1) At low strains the A/t values are nearly the same for the three orientations. 2) As strains increase, A/t drops most rapidly for [Ill.] and less rapidly for [211], while for the maximum shear-stress orientation it is constant during easy glide and drops abruptly at the termination of easy glide. 3) In stage 11, A/t values are again approximately the same for the three orientations. These observations are regarded as evidence that 1) the initiation of slip produces obstacles of essentially the same effectiveness for all of these orientations, while 2) the rate at which slip obstacles are produced before stage I1 is fully developed is strongly controlled by the amount of slip on more than one system. This second statement is consis-

Jan 1, 1961