Search Documents

By Nelson B. Russell, Donald C. Bond

The effects of various antifreeze agents on the formation of hydrogen sulphide hydrate have been studied. On a molar basis the relative lowering of Tm (the maximum temperature at which solid hydrogen sulphide hydrate can exist in equilibrium with the given solution) for the various agents is: sodium chloride 1.00, calcium chloride 1.71, methyl alcohol 0.57, ethyl alcohol 0.68, ethylene glycol 0.73, diethylene glycol 0.73, sucrose 0.87, dextrose 0.71. On a weight basis the relative lowering of TM is: sodium chloride 1.00, calcium chloride 0.91, methyl alcohol 1.08, ethyl alcohol 0.89, ethylene glycol 0.69, diethylene glycol 0.41, dextrose 0.23, and sucrose 0.15. Introduction The solid hydrate of hydrogen sulphide, H2S.6H20,1 is in equilibrium with water and liquid hydrogen sulphide at 85°F at a partial pressure of hydrogen sulphide approximately equal to the vapor pressure Of hydrogen sulphide at that temperature. At temperatures below 85°F, in the presence Of excess hydrogen sulphide (greater than the amount required to react with the water present) the hydrate is in equilibrium with liquid hydrogen sulphide at approximately the vapor pressure Of hydrogen sulphide. In the presence of excess water, the solid hydrate is in equilibrium with liquid water, containing dissolved hydrogen sulphide, at a pressure lower than the vapor pressure of liquid hydrogen sulphide at the same temperat~re.2 The lower the temperature, the greater the difference between the decomposition pressure of the hydrate and the vapor pressure of liquid hydrogen sulphide at that temperature. Conditions conducive to the formation of solid hydrogen sulphide hydrate may exist in wells producing a gas containing a high percentage of hydrogen sulphide under high pressure, or in the lead lines from such wells. This paper gives the results of tests made with various antifreeze agents which might be useful in decomposing the hydrate or in preventing the formation of the hydrate of hydrogen sulphide Apparatus Fig , shows a diagram of the apparatus used. The sample under observation was contained in a glass tube 34 cm long, having a 6 mm id and a wall thickness of 2.5 mm. The lower end of this tube was closed- with a plug of butyl rubber. The upper end of the tube was connected to a diaphragm gauge, with a stainless steel diaphragm, a manometer, a vacuum pump, and a cylinder of hydrogen sulphide, The tube was held nearly horizontal, with the liquid resting along the lower side of the tube. It was found that when the tube was held in a vertical position, it broke with ex. plosive violence as soon as it became filled with solid hydrate. Presumably this was caused by the expansion which occurred on solidification of the hydrate. The difficulty disappeared when the tube was held in an inclined position during the tests.

Jan 1, 1949

By Howard A. Meyerhoff

IN western Argentina, in the Province of Mendoza and the Territory of Neuquén, there is a series of solid bitumen deposits which are claimed to be the most extensive in the world. In a linear belt 500 km (311 miles) long, roughly paralleling the axis of the Andes but occupying a variety of positions with respect to the orogenic structures, more than 100 outcrops have been reported. Approximately 70 of these have been prospected, and some mining has been planned or attempted for about half this number. Limited tonnage, high sulphur content, inaccessibility, labor shortages, and disastrous fires have taken a heavy toll among these operations, and in 1947, only 4 deposits were being actively mined, but 8 more were being explored and developed with a view to placing them in production. Inasmuch as these deposits are currently yielding a substantial fraction of Argentina's limited domestic supply of solid fuels, a brief account of the deposits and of the small industry based upon them will provide a commentary on Argentina's fuel problem. CHARACTER OF SOLID BITUMENS The solid bitumens of Mendoza and Neuquén are petroleum derivatives, as is indicated by the following ultimate analysis: [CONSTITUENTS PER CENT Hydrogen6.8 Carbon82.4 Nit.rogenI.6 Oxygen2.7 Sulphur2.2 Ash4.3 100.0] In physical appearance they bear a close resemblance to coal and are commonly called carbón. Their specific gravity has an extreme range of 1.10 to 1.777 in 36 samples weighed, but the average is between 1.14 and 1.24. The material is black, lustrous to dull, with blocky to sub-conchoidal fracture. Though brittle, the purest material is softer than anthracite and exhibits slightly more cohesion. This bituminous material is generally known as asfaltita or asphaltite, but definitive chemical studies indicate that the term asphaltite or grahamite can be applied correctly only to the exceptionally pure material of the Auca Mahuida district in Neuquén. Some other name should be used for the chemically variable bitumens found in all other districts, and the designation "asphaltitic pyrobitumen" has been proposed by Carlos A. S. Piscione.1 At the present time these bitumens, are finding favor as solid fuel and as a gas-producing medium. They yield heat values of 8650 to 9750 cal,2 or 14,500 to 16,750 Btu per pound, and in consequence of their excellent heating qualities and the scarcity of imported coal, they are marketed as far away as Buenos Aires at a price of go to 95 pesos, or approximately $22 to 23, per metric ton. In burning, the material swells and decomposes into solid, fluid, and gaseous fractions which burn violently though nonexplosively. Its combustibility has been responsible for disasters and virtually complete destruction at Mina La Esperanza and Mina Santa Marta, and for minor mishaps elsewhere, as at Mina Escondida in August 1947.

Jan 1, 1947

By J. S. Aronofsky, H. J. Ramey

Potentiometric model studies of the five-spot water flood to determine the influence of mobility ratio upon injection or production histories are described. The results suggest a method for the correlation of data from field pilot tests for the estimation of an effective mobility ratio and its effect upon field water floods. The effect of the well spacing-to-well radius ratio upon production histories is presented. A method of accounting for this factor is suggested. The influence of injection (or production) rates and injection and production well pressures upon production histories is shown. The five-spot well pattern was investigated for water-to-oil mobility ratios of 0.1 to infinity. INTRODUCTION It has been well established that mobility ratio has an important effect upon flood patterns.1,2,3,4,5 It should be equally apparent that injection and production histories must also be influenced by mobility ratio. However, none of the articles referred to above mention the importance of being able to predict the effect of well pressures (or injection rates) during the entire time history of a waterflood operation. A complete description of production histories (the terms "injection" and "production" are synonymous for the steady-state model under consideration) would provide values for well pressures and interface positions at any time for a specified injection rate. conversely, if the waterflood problem is specified in terms of a constant injection well pressure, then it would be desirable to know the injection rate and interface positions at any time. This paper describes the results of potentiometric model studies which were used to analyze the influence of mobility ratio on injection or production histories. A method is presented for calculating production histories over a range of ratios of well spacing-to-well radius. The basic method described in this paper to evaluate production histories is to: (1) determine interface position as given in Ref. 1, and (2) measure electrical current and voltage drop for each interface position. It should be mentioned that the current state of knowledge on flood patterns as affected by mobility ratio shows that significant discrepancies exist between the results of various investigators2,3,4,5. It is beyond the scope of this paper to discuss the reasons for such discrepancies. However, the method of determining production histories presented in this paper could be applied to any of the swept-area patterns presented in the literature. All results given in this paper are based on a set of swept areas obtained by the potentiometric method. Potentiometric analyzer technique is adequately described in the literature, but the basic assumptions involved in work of this nature bear repetition. It is assumed that: 1. A distinct oil-water interface exists in the reservoir; only water is mobile in the region behind the interface (water zone) and only oil is mobile in the region ahead of the interface (oil zone). 2. There is a fixed mobility value, (k/µ) w associated

Jan 1, 1957

By Reed W. Hyde

Some information has been published on the sulphur dioxide concentration of gases from D wight-Lloyd machines sintering lead ores but most of this relates to the customary practice in which the charge is relatively high in lead and is sintered in two passes Over the machine. It is thought, therefore, that the following observations on sintering in one pass a low-lead, low-sulphur charge may be of interest. The data were obtained in sintering lead sulphide notation concentrates mixed with minus 20.mesh oxide ore, the mixture carrying 16,8 per cent Pb and 5.3 per cent S. No returns were used because of the limited amount of sulphur available as fuel, but the mixture pelletized readily. to make a satisfactorily permeable bed on the sintering machine. As there was a possibility that the SO z might be utilized, a series of runs was made to determine the concentration ofSO2 in the gases at different points along the wind box, and the effect on this concentration of changes in the wind-box vacuum. Several runs each were made with vacuums (as measured in inches of water at the wind box) of (1 2 to 1 in., ('1 4 to 3% in. and (3) 6 to 5% in. The averages of the determinations from each series are platted On the graph (Fig, 1). The vertical scale shows the percentage by volume of SOz (as determined by the Reich method), and the horizontal scale shows the time e~pressed as percentage of the total sintering time. Sintering was considered to be complete when no SOz could be detected in the gases. In all cases the depth of bed was 4 1/2 in. and the weight of dry charge per square foot of hearth area was 45.2 lb. Other data are given in the table. The volume of gases corresponding to the several points along the wind box at which SO2 determinations were made could not be measured, but has been calculated from the SO2 Content and sulphur elimination on the assumption that the volume is uniform throughout the sintering period. This is not strictly true, as with a given vacuum the volume usually will drop slightly toward the middle of the period and increase toward the end. However, this made is a reasonable approximation. several interesting features are brought out by these data. In general, the published data on SO 2 concentration in sintering under ordinary conditions show a high SO2 concentration in the early stages followed by a rapid decrease in concentration and with relatively little SOz in the gases from the last half or third of the operation. In other words, the greater part of the sulphur elimination is obtained in the first third or half of the period. In these runs, the 6-in. vacuum, which approximates the usual operating condition, gives a curve that follows this customary pattern. Maximum SO2 concentration is obtained 234 min. after

Jan 1, 1944

By J. W. Borough

THE electrical conductivity of pure copper is markedly decreased by small amounts of impurity in solution. The magnitude of this effect has been very carefully determined by numerous investigators who studied a wide variety of impurity elements. Much of this work is summarized in an excellent review by Pawlek and Reichel.' The case of zinc impurity in copper is an exception to the above in that there has been no well-documented study of the effect using high-purity starting materials. The values for the effect of zinc on conductivity, which are usually taken from unpublished work by Skowronki, indicate that zinc in low concentration has no effect whatever in lowering the conductivity of pure copper. This effect, if true, is unusual since it is generally known that even in lowest concentration, impurities exert an effect on conductivity which is proportional to the amount dissolved. It is more reasonable to suspect that in the original work on the effect of zinc some of the zinc was oxidized out of solution during specimen preparation. The following experi- and calculated d-spacings based on the unit cell dimensions of Baenziger et al. Since the single crystal studies of Baenziger et al. were limited to (hk0) and (hk 1) data, it was not possible to Compare all the intensities of the powder and single crystal patterns. However, the strongest reflections of both studies, the (321) reflection, agree very well when the appropriate multiplicity factor is used. Good agreement was also found in a number of other reflections of lesser intensity. Despite the precautions taken in annealing the U6Fe powder, an appreciable amount of UO, was detected in the powder pattern after heat treatment. The powder pattern reported by Groganoand Clews is given in Table I. Except for the 3.15A line, which is the strongest line of UO,, their pattern, as far as it goes, compares favoEably with the data from this study. Gordon and Kaufmann have reported a diffraction powder pattern purported to be U, Fe but it bears very little resemblance to the patterns of Table I. ments were carried out to redetermine the effect of zinc on conductivity using high-purity starting materials and processing conditions capable of producing oxygen-free alloys. Materials used in the experiment were ASR 99.999 pct Cu and Cumingo 99.999 pct Zn. Four 1 lb melts were prepared with identical procedure in argon atmosphere with crucibles made from Speer No. 580 graphite. The compositions were 0.0, 0.1, 0.3 and 1.0 pct Zn. Standard No. 14 wire (0.064 in. diam) was made from these melts as follows. The 1 pct Zn sample was first reduced 94 pct by cold swaging with five annealing treatments of 800o for 10 min in hydrogen between swagings, and then reduced 94 pct to the

Jan 1, 1962

By L. J. Dijkstra, R. J. Sladek

IN earlier work the effect of manganese on the general behavior of nitrogen in iron was the subject of a careful examination by Fast.' Part of the investigation was made, in collaboration with one of the present authors (L.J.D.), by using the internal friction method. This technique, which has been described elsewhere,' showed some significant changes in the properties of Fe-N alloys by the addition of a small amount of manganese namely: 1—Under standard conditions the maximum of the nitrogen peak in pure iron appears around 20 °C and the half width is about 27 °C. By addition of 0.5 atomic pct Mn a general broadening of the internal friction peak occurs. The half width is increased by about 9°C. Moreover, a shift of the maximum of about 5°C toward a higher temperature takes place, Fig. 2. 2—The precipitation of nitrogen from the supersaturated solution, measured, e.g., at 200 °C, was inhibited by the addition of the amount of manganese given in effect 1. The broadening of the nitrogen peak was confirmed in more recent work3 on samples which were prepared from Westinghouse Puron iron. The effect of manganese on the rate of precipitation, however, was much less striking than in the earlier work' based on Philips high purity iron. Theory To explain the first change in properties just referred to, effect 1, the following two assumptions were made:' First, every manganese atom in sub-stitutional solid solution creates around it six interstices located between an iron and a manganese atom, as is evident from Fig. 1. These interstices, conveniently called Fe-Mn interstices, have for nitrogen a free energy level which is AG* lower than the normal Fe-Fe interstices between two iron atoms. For such low concentrations of manganese as 0.5 atomic pct, the possibility that two manganese atoms will be nearest neighbors can be disregarded. Second, it is assumed that in addition to the normal relaxation time TFe at least one new relaxation time, Mn, Fe, enters in the phenomena which is associated with the elementary diffusion jumps between a Fe-Mn interstice and an adjacent Fe-Fe interstice. Fig. 1 gives schematically the free energy for a nitrogen atom as a function of its position along the line ABC. A tentative analysis of the nitrogen peak in a 0.5 pct Fe-Mn alloy based on these assumptions has been made in Fig. 2. The dotted curve with a maximum at 22°C is caused by jumps between Fe-Fe interstices, the dotted curve with maximum at 32°C by jumps between an Fe-Mn and an Fe-Fe interstice. The two effects added together give the dash-dot internal friction curve for the alloy. In the following these two components will be referred to as the normal peak at 22°C and the abnormal one. (The small secondary peak at

Jan 1, 1954

By J. G. Benford, E. B. Stanley

THERE have been numerous papers in the literature1 on the subjects of secondary and tertiary recrystalli-zation in silicon steels. Secondary re crystallization is believed to occur in silicon steel by either a surface-energy phenomenon such as in the usual development of cube texture or by a second-phase phenomenon such as in the usual production of cube-on-edge texture, (110)[001]. Tertiary recrystallization in silicon steel is thought to be a surface-energy phenomenon in which, for example, grains having a (110) plane parallel to the sheet grow at the expense of other grains in the matrix including those having a (100) plane parallel to the plane of the sheet. In all these instances, the orientations involve either a preferred (100) or (110) plane in the plane of the sheet. Until very recently, there had been no experimental evidence reported of the occurrence of a texture by secondary or tertiary recrystallization that involves a (111) plane in the plane of the sheet, although Kohler reported that grains having the (111) plane parallel to the sheet surface can also grow by a surface energy mechanism. Stickels observed a secondary texture in iron described as "near {554}(225)" about 5 deg from {lll}(211).3 Mee reported that in a vacuum-remelted commercial 3 pct Si steel {lll}(hkl) secondary recrystallization took place in a high vacuum and in pure hydrogen.4 Recently in our Laboratory, large-grained structures such as shown in Fig. 1 having an orientation near (111)[211] or (111)[2ii] have been observed. The arrows point to areas of relatively small matrix grains of the kind that the much larger (111) grains consumed while growing. It is of interest that the matrix grains of samples annealed at 2000°F were essentially the same size as those in samples annealed at 2200°F, a matrix-grain-size stability that is characteristic of secondary recrystallization processes. A torque disc taken from Grain 4 of the sample shown in Fig. 1 revealed a very flat magnetic-torque curve, as expected, with a maximum torque of 7000 dyne-cm per cu cm compared to the typical 180,000 dyne-cm per cu cm observed for conventional (110)[001] textured material. A back-reflection Laue pattern for Grain 4 is shown in Fig. 2 and indicates a near-perfect (111)[211] orientation. The other six numbered grains in the sample of Fig. 1 had a similar orientation. The small circles next to each number were the target areas for the X-ray beam. The starting material was an 0.011-in.-thick oriented silicon steel, (110)[001] texture, containing 3 pct Si. It was lightly pickled, cold-rolled to 0.005 in., and annealed 4 hr at 2200°F within a nickel box (not gas-tight) inside a tube furnace through which dry hydrogen was flowing. The samples were heated to 1500°F in 1 hr and then at 60°F per hr to 2200°F. There were other

Jan 1, 1969

By W. C. Winegard, C. Elbaum, T. Ojala

NONOCTAHEDRAL slip was observed in poly- crystalline aggregates of aluminum by Boas and Ogilvie.&apos; These authors indicate that the non-octahedral slip takes place on (100) or (110) planes. Ogilvie2 studied the continuity of slip lines across grain boundaries in polycrystalline aluminum. Non-octahedral slip was observed by him, but it was not reported to occur in the continuous slip lines across the grain boundaries, which were identified as octahedral slip in all cases. The present note reports the observation of non-octahedral slip in the grain boundary region of an aluminum bicrystal and tricrystal, both deformed in tension at room temperature. An analysis is made, which leads to a probable identification of the non-octahedral slip planes as (110) and (331). The specimens used were of rectangular cross section, approximately 5x10x200 mm. They were prepared by growth from the melt, using aluminum reported by the manufacturer to be 99.994 pct pure. The grain boundaries were in a plane perpendicular to the wider face and parallel to the long dimension of the specimens. The axis of tension was also parallel to the long dimension of the specimen. The orientations of the specimens studied were determined by the Laue back-reflection method and are given in Fig. 1. The nonoctahedral slip was first observed after about 6 pct extension in the bicrystal, and after about 2 pct extension in the tricrystal. The micrograph, Fig. 2, of the grain boundary region of the bicrystal shows two active slip planes throughout each of the two crystals, with a third plane active at the grain boundary in each crystal. Two major sets of slip traces observed in grain No. 1 are consistent with the operation of the slip systems (ill) [oil] and (111) [011]. The nonoctahedral slip takes place on a plane belonging to a <111> zone, as determined by drawing trace normals. Assuming that slip will take place only in the <110> direction, the planes in the <111> zone, which do not contain that direction, need not be considered. Among the remaining prominent planes of that zone, the (011) plane has a common slip direction—the [011]—with the (111) plane, which acts as one of the octahedral slip planes. In grain No. 2, a similar situation to that in grain No. 1 is observed. As indicated previously, the (oil) plane in the <111> zone, to which the nonoctahedral slip plane belongs, has a common [Oil] slip direction with the acting (ill) slip plane. Also, the orientation of the (oil) plane in grain No. 2 almost coincides with the orientation of the acting (111) slip plane in grain No. 1. Similarly, the orientation of the (oil) plane in grain No. 1 almost coincides with the orientation of the acting (111) slip plane in grain No. 2. It is, therefore, possible that the nonoctahedral slip was induced, in both cases, by octahedral slip in the neighboring grain. It is important

Jan 1, 1957

By M. Oka, C. M. Wayman

It has been known for some time1 that (110)b twinning is possible in bct martensite.* Any plane of the form (110) not parallel to the fourfold axis of tetra-

Jan 1, 1969

By T. A. El-Bassyouni, Paul Gordon

Grain-gvowth data in zone-refined aluminum and in dilute alloys of copper with this aluminum have been obtained. The amounts of copper added were from 4 to 400 at. ppm. It was found that in both the unalloyed aluminum and the alloys grain growth was characterized by a high value of n in the isothermal growth equation 6n = Kt The inadvertent presence of 1 at. ppm Fe in the alloys was found to he more potent in slowing growth than the purposely added copper. Possible rationalizations of these observations and their general relevance to the theoretical use of gvain-grozvth data have been discussed. Grain growth data of Winegard and his co-workers&apos; on zone-refined tin and dilute tin alloys were analyzed with some success2 in terms of approximate theoretical equations for boundary migration.2-4 In view of this success, experiments were carried out in an effort to obtain similar data on zone-refined aluminum and on dilute copper-in-aluminum alloys. The results obtained were anomalous in several respects and could not be used to test theory. A discussion of these anomalies is presented here; they have been attributed to impurity effects and serve to emphasize the sensitivity of grain growth in general—and the particularly high sensitivity in aluminum—to impurities. The resulting difficulties in the theoretical use of grain-growth data are also discussed. EXPERIMENTAL DETAILS An aluminum bar was zone-refined and leveled by methods similar to those described previously.&apos; The degree of purity obtained is indicated in Table The data in Table I were determined by mass-spectrographic methods through the courtesy of Mr. Thomas A. Johnson of AIAG Metals, Inc.* Three dilute copper alloys with this aluminum were prepared also by methods described previously.&apos; The alloys contained nominally 4, 40, and 400 at. ppm of Cu, respectively (0.001, 0.01, and 0.1 wt pct). Each material was fabricated by swaging and rolling into a round bar about 1/4 in. in diameter with an annealed penultimate grain size of approximately 0.003 to 0.007 cm. In order to minimize preferred orientation the fabrication was carried out in several steps, each consisting of a reduction of about 40 pct followed by a recrystallization anneal. Annealing temperatures for the grain-growth studies were attained by the use of boiling liquids up to 213°C and molten metal baths at higher temperatures. Temperatures were controlled to within 1°C. Samples for measurements were cylinders about 3/4 in. long and 1/4 in. in diameter cut from the fabricated rods. In the interests of sample economy a single sample was used for the grain-growth measurements at each temperature. Each sample was, thus, annealed for several successive periods of time, the grain size being measured at each annealing period on a transverse surface exposed by

Jan 1, 1965

By Cuppam Dasarathy

THE object of this note is to report briefly certain results of investigations on the Fe-In phase diagram. BISRA-high purity H-iron and 99.9 pct pure indium were used to prepare the alloys. The experimental techniques consisted of thermal analysis, optical metallography, and X-ray diffraction. A phase diagram based on the present results as well as those reported earlier by the author&apos; is shown in Fig. 1. It is seen that the liquidus points fall on a smooth line which meets the monotectic isotherm at 1470°C. The liquidus extends up to 3.4 at. pct In. The phase boundary separating the two liquidus L1 and L2 is shown dotted. The experimental solidus meets the monotectic isotherm at -0.9 at. pct In. The 6/6 + L2 boundary drops steeply to the 6 + La/y + L2 boundary at -1350°C. In this region, it is impossible to detect satisfactory thermal arrests because of the steep phase boundary. The present diagram shows that indium lowers the temperature of the d/y transforma-tion and raises the temperature of the y/a transfor-mation. The y +d region is found to be very narrow. Indium gives rise to a restricted y field when alloyed with iron. The width of this field is between 0.4 and 0.5 at. pct In. Details of the alloys containing 40 and 50 at. pct In have already been reported by the author&apos; and the transformation temperatures of these alloys are included in Fig. 1. It appeared from optical metallography and X-ray diffraction that the room temperature solubility of indium in a iron is less than 0.28 at. pct since alloys of 0.28 at. pct In and above, slow cooled to room temperature, contained dark etching second phase particles situated both in the matrix and grain boundaries of the a-grains, see Figs. 2 and 3. These particles were identified to be unalloyed indium by X-ray diffraction. The lattice parameter of the a phase reached a maximum of 2.8672A at the indium level of -0.28 at. pct. The present diagram, Fig. 1, is in substantial agreement with that of Stadelmaier and Fiedler&apos; except for certain differences in detail. For example, they found the monotectic composition and temperature to be 7.0 at. pct In and 1443oC, respectively, while the present work indicates them to be 3.4 at. pct In and 1470°C. The 6 + L2/y + L2 transformation is indicated in the present work to occur at -1350°C, whereas Stadelmaier and Fiedler find this to occur at -1320°C. They also claim that the width of the y field is 0.2 at. pct In while the present work shows the width to be between 0.4 and 0.5 at. pct In. 1) Indium, when alloyed with iron, gives rise to a restricted y field, the width being >0.5 at. pct In.

Jan 1, 1970

By W. J. Reagan

All of the material described in the following paper is within the following specifications: carbon, 0.50 to 0.85 per cent; phosphorus and sulfur, 0.04 per cent max.; manganese, 0.60 to 0.85 per cent; silicon, 0.20 to 0.30 per cent. Steels with much lower carbon contents can be handled in exactly the same manner. One of the first things necessary to basic open-hearth slag control is uniformity of charge, particularly as to the silicon content and the percentage of lime charged. Our past work has shown that the silicon content of the charge is more important than the carbon content in determining the carbon at which a heat will melt. We have found that by keeping the silicon content of the charge about 0.60 to 0.65 per cent, and with a lime charge of about 7 per cent (limestone equivalent), our heats melt sufficiently high in carbon to allow a moderate feed of ore and the slag will be of low iron oxide content. In making a heat of 0.75 carbon steel we endeavor to have the heat melt at about 1.20 per cent carbon. The iron oxide content of the finishing slag depends upon the final phosphorus desired; for a given ratio of lime-silica in the slag, the lower the phosphorus desired in the final steel, the higher the iron oxide content of the finishing slag must be. By reducing the lime charge to a minimum, the heats melt faster, and by keeping the silicon content at the desired figure the heats melt with a high SiO2 slag, which has been shown in previous work to give a low iron oxide slag. In most of our work, using a 180,000-lb. charge and with basic pig containing about 1.20 per cent silicon, we use a lime charge of 8500 lb. of limestone and 2000 lb. of burnt lime. The pig charge is about 48 per cent of cold pig, and the charge contains a large percentage of works scrap. This causes a heat to melt with about 1.20 to 1.30 per cent carbon, for a heat that will finish about 0.75 per cent carbon. This gives a heat that will need a feed of about 2000 lb. of ore, and also a slag with an FeO content of about 4 to 5 per cent at melting. The additional FeO obtained from the ore addition will bring the FeO in the slag at tapping to about 6 to 7 per cent. It is necessary to carry quite a fluid slag to prevent pickup of FeO, as a too heavy slag causes FeO to build up in it, giving a finishing slag with a greater FeO than is desired. By adjusting the lime charge of a basic open-hearth heat, a very sensitive adjustment of the slag may be obtained. The figures in Table 1

Jan 1, 1935

By W. J. Reagan

All of the material described in the following paper is within the following specifications: carbon, 0.50 to 0.85 per cent; phosphorus and sulfur, 0.04 per cent max.; manganese, 0.60 to 0.85 per cent; silicon, 0.20 to 0.30 per cent. Steels with much lower carbon contents can be handled in exactly the same manner. One of the first things necessary to basic open-hearth slag control is uniformity of charge, particularly as to the silicon content and the percentage of lime charged. Our past work has shown that the silicon content of the charge is more important than the carbon content in determining the carbon at which a heat will melt. We have found that by keeping the silicon content of the charge about 0.60 to 0.65 per cent, and with a lime charge of about 7 per cent (limestone equivalent), our heats melt sufficiently high in carbon to allow a moderate feed of ore and the slag will be of low iron oxide content. In making a heat of 0.75 carbon steel we endeavor to have the heat melt at about 1.20 per cent carbon. The iron oxide content of the finishing slag depends upon the final phosphorus desired; for a given ratio of lime-silica in the slag, the lower the phosphorus desired in the final steel, the higher the iron oxide content of the finishing slag must be. By reducing the lime charge to a minimum, the heats melt faster, and by keeping the silicon content at the desired figure the heats melt with a high SiO2 slag, which has been shown in previous work to give a low iron oxide slag. In most of our work, using a 180,000-lb. charge and with basic pig containing about 1.20 per cent silicon, we use a lime charge of 8500 lb. of limestone and 2000 lb. of burnt lime. The pig charge is about 48 per cent of cold pig, and the charge contains a large percentage of works scrap. This causes a heat to melt with about 1.20 to 1.30 per cent carbon, for a heat that will finish about 0.75 per cent carbon. This gives a heat that will need a feed of about 2000 lb. of ore, and also a slag with an FeO content of about 4 to 5 per cent at melting. The additional FeO obtained from the ore addition will bring the FeO in the slag at tapping to about 6 to 7 per cent. It is necessary to carry quite a fluid slag to prevent pickup of FeO, as a too heavy slag causes FeO to build up in it, giving a finishing slag with a greater FeO than is desired. By adjusting the lime charge of a basic open-hearth heat, a very sensitive adjustment of the slag may be obtained. The figures in Table 1

Jan 1, 1935

By K. Tangri, M. Chaturvedi

The addition of 0.5 wt pct Cu to Zr-2.5 Cb alloy increases the as -quenched hardness of the hexagonal martensitic a&apos; phase, produced by water-quenching bccß-Zr phase, by about 35 pct. This strengthening has been attributed to the solid -solution hardening of the matrix. On aging ternary martensite, a&apos; phase reverts to equilibrium a and Zr2Cu and ß-Cb precipitate out, mainly at the twin and grain boundaries, causing a secondary hardening of the matrix. COLD-worked Zircaloy-2 pressure tubes have been in use in power reactors for a considerable period of time. The search for a better material led to the development of Zr-2.5 wt pct Cb alloy which in the quench-aged condition develops 50 pct more strength than that of cold-worked Zircaloy-2, however, its corrosion resistance in water and steam in the temperature range of 316" to 400°C, in absence of neutron flux, is inferior to that of zircaloy-2.&apos; Work carried out by Ells et al.1 and Dalgaard2 has shown that the corrosion properties of Zr-2.5 wt pct Cb alloy can be considerably improved by the ternary addition of 0.5 wt pct Cu. This paper is concerned with the effect of 0.5 wt pct Cu on the formation of martensitic a and its aging characteristics in a Zr-2.5 wt pct Cb alloy. MATERIALS AND EXPERIMENTAL TECHNIQUES Zr-2.5 Cb-0.5 Cu (referred to as the ternary alloy) and Zr-2.5 Cb (referred to as the binary alloy) alloys, supplied by the Chalk River Nuclear Laboratories of the AECL were used. The detailed chemical analysis is given in Table I. Cold rolling and swagging with frequent intermediate anneal of 1000°C were used for the initial fabrication of the alloys. All the heat treatments were carried out after the specimens were wrapped in zirconium foils and encapsulated in silica tubes under a vacuum of 5 x 10-6 mm of Hg. For optical metallography and hardness measurements specimens were mechanically and then chemically polished in a 45 pct HNOj, 45 pct HzO, and 10 pct HF solution. Hardness was measured on a Vickers hardness tester using a 10-kg load. For each specimen at least fifteen indentations were made in order to obtain a representative value. The phase identification and structural analysis were carried out using X-rays and electron diffraction techniques. Wires of 1.5 mm diam reduced to 0.12 mm diam by chemical etching were used for making Debye-Scherrer powder patterns using Cu Ka radiation in a 114.6 mm diam camera. Carbon extraction replicas were prepared by etching the specimens, after depositing a layer of carbon on the metallographic specimen, in one part HF and thirty parts ethyl alcohol. Thin films were prepared by electropolishing heat-treated 3/4 by 1/2 by 0.005 in. thick strips using a modified Bollman-Window technique. The 10 pct perchloric acid-90 pct methyl alcohol bath was kept at -50°C and polishing was done at 5 to 10 V. The thinned specimens were washed in ethyl alcohol at -30º to -40°C and dried between filter papers. Replicas and thin films were examined in a Phillips 300 G electron microscope. For resistivity measurements thin strip specimens 0.02 by 0.3 by 10.0 cm long were used. The potential leads were spot welded to the specimens in order to maintain a fixed length for the initial and the final resistivity measurements. The resistivity was measured by a Kelvin bridge in a temperature controlled room. The temperature was maintained at 72º ±1°F and the accuracy of the resistivity measurements was 0.03 µa-cm. RESULTS As-Quenched Structures. In order to produce a homogeneous matrix to study the precipitation reaction the solution-treatments of both the alloys were carried out in the -field region. From the Zr-Cb phase diagram due to Lundin and cox3 ß/a + ß phase boundary for Zr-2.5 wt pct Cb alloy is 820°C. Ells et al.1 have reported this boundary for Zr-2.5 Cb alloy containing 1100 ppm 0 to be at 920°C. Also, the addition of 0.5 wt pct Cu reduces this temperature by 50°C. Therefore, the solution-treatments were carried out at 1000°C to ensure that the alloys were in ß-phase region. The soaking time was 1 hr and the specimens were water-quenched. The as-quenched hardness of the binary alloy was 245 Vpn whereas, that of the ternary alloy was 330 Vpn. The X-ray diffraction studies indicated that the as-quenched structure of both the alloys consists of martensitic hexagonal phase a&apos;, with a c/a ratio of 1.591, and some retained ß-Zr. The presence of a&apos; phase was further confirmed by thin film electron microscopy. Electron micrographs of typical ß-quenched structures of the ternary and the binary alloys are shown in Figs. 1 and 2, respectively. Fig. 3 shows the diffraction pattern from an area similar to that shown in Fig. 1. Although, the as-quenched hardness of the ternary alloy is about 35 pct greater than that of the binary alloy, the structure of both the alloys seems to be the same. The matrix of both alloys is heavily twinned and shows very few dislocations. Furthermore, there is no evidence of any precipitation taking place in either of the two specimens during quenching from the solution-treatment temperature. Aging Behavior of Martensitic a&apos;. The aging kinetics of the ternary alloy were followed by resistivity and hardness measurements. The as-quenched values

Jan 1, 1970

By Francis H. Brownell

During the 1920&apos;s lead consumption in the United States reached the highest average total ever known. For the ten-year period 1921-&apos;30, it was slightly over 600,000 tons per year, or say 50,000 tons per month, and the price averaged 6.81 per lb. But the I930&apos;s witnessed a severe drop in the consumption of lead is in other business activities. The average U.S. consumption for the ten-year period 1930-&apos;40 was slightly less than 380,000 tons per year, or under 32,000 per month, with the average price dropping to 1.191c. per lb. The outlook in early 1939 was for a continuation of this average consumption and price a demand of 35,000 to 40,000 tons per month, and a price level of 4 1/2 to 5c. in the United States.

Jan 1, 1941

By R. E. Somers

1. INTRODUCTION 1. Location, Topography, and Climate The Burro Mountains are located in the southwestern part of New Mexico, in Grant County. The group is made up of two distinct moun-tain masses, known as the Little Burros and the Big Burros, the former lying about 6 miles southwest of Silver City-, and the latter about 9 miles farther in the same direction. They are separated by the valley of the Mangas River, a tributary of the Gila, and a stream only in name, except after a heavy down-pour of rain. . The Little Burros attain an elevation of 6,625 ft. above sea level, and the Big Burros 8,054 ft., with the surrounding country averaging about 6,000 ft. To the south of these mountains stretches the desert plain, while to the north are the more frequent elevations of the mountainous country.

Jan 5, 1915

By Eckley B. Coxe

(WITH FIGURES ON PLATES II, III, AND IV.) I DESIRE to call the attention of the Institute to two deep vertical shafts, which are now being sunk in Schuylkill County, Pennsyl¬vania, about 1 1/2 miles north of Pottsville. These shafts are of interest to the mining engineer, not only on account of the novelty of the method of sinking adopted, which promises to produce a revolution in that branch of mining engineering, but also as examples of the manner in which such work should be undertaken. GEOLOGICAL SKETCH OF THE TERRITORY TO BE WORKED BY THE SHAFTS AND REASON FOR SINKING THEM. The Mammoth or E Vein of the anthracite coal-measures in that part of the Schuylkill region near and north of the town of Pottsville lies at a great depth below the surface, and has, in consequence, never been worked in that locality.

Jan 1, 1873

SEC. 1. The membership of the Institute shall comprise seven classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Members; 6. Rocky Mountain Members; 7. Junior Foreign Affiliates. All shall be equally entitled to the privileges of membership, excepting that no member of any class whose residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall be entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the class of Member must be at least 27 years of age and must have had at least six years&apos; employment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain Members.

Jan 1, 1946

By Paul Weir

Bleaching clays have been used extensively in the oil-refining industries for a number of years. Their use in water purification is relatively recent and less extensive. They are frequently classified as (1) those naturally active and (2) those active after artificial activation with acid. Fuller&apos;s earths fall within the general group of bleaching clays and gradually the commercial term "fuller&apos;s earth" has been applied to natural clays originating, for the most part, in the southeastern section of the United States. Bentonitic clays are usually classed as activable and are prevalent in the southwestern section of the United States.l Bleaching clays vary considerably in chemical and physical properties throughout the country, or even in different parts of one deposit (Table 1). The fuller&apos;s earth type of clay is characterized by a lack of plasticity, relatively adsorbent, foliated structure, and does not swell to form a

Jan 1, 1942

By Paul Weir

Bleaching clays have been used extensively in the oil-refining industries for a number of years. Their use in water purification is relatively recent and less extensive. They are frequently classified as (1) those naturally active and (2) those active after artificial activation with acid. Fuller&apos;s earths fall within the general group of bleaching clays and gradually the commercial term "fuller&apos;s earth" has been applied to natural clays originating, for the most part, in the southeastern section of the United States. Bentonitic clays are usually classed as activable and are prevalent in the southwestern section of the United States.l Bleaching clays vary considerably in chemical and physical properties throughout the country, or even in different parts of one deposit (Table 1). The fuller&apos;s earth type of clay is characterized by a lack of plasticity, relatively adsorbent, foliated structure, and does not swell to form a

Jan 1, 1942