Search Documents

By J. B. Newkirk

IN 1939 Bitter and Kaufmann1 suggested that iron, precipitating from a copper-rich, Cu-Fe solid solution, appears initially as coherent particles of r-Fe which transform to the body-centered-cubic form of iron when the alloy is cold worked. Since then there has been considerable discussion, supported only by indirect evidence, regarding the validity of the concept. For example, Reekie, Hutchison, and Hether-ington2 interpreted the changes in electrical resistance accompanying the aging of Cu-Fe specimens in terms of a coherent 7-Fe precipitate which transformed to the incoherent a-phase during long aging or cold working. Greninger- ound that Cu-Fe alloys which had been water quenched from 1050" and then held at 650°C for 3 hr changed from weakly to strongly ferromagnetic as the aged wire was subsequently cold worked. He also found diffraction lines corresponding to body-centered-cubic iron in Debye-Scherrer patterns given by aged and worked specimens but lines corresponding to only one face-centered-cubic phase in specimens which had been aged but not worked. Knoppwost,' and later Cech and Turnbull,5 found that aged Cu-Fe specimens showed a slight increase in ferromagnet-ism after they had be? cooled in liquid nitrogen. Very recently Denney6 followed the kinetics of the precipitation reaction as indicated by the saturation magnetization, hardness, and diffuse X-ray effects. The experimental results reported by all of the authors mentioned above are readily explained in terms of the Bitter and Kaufmann concept. However, most of the evidence is indirect when used to define the structural changes involved. It was the aim of the present investigation to determine the mechanism of precipitation of iron from a Cu-Fe solid solution in the light of available published information and with additional new and more direct experimental data. Experimental Method At 1060°C copper will contain up to 3 atomic pct Fe in equilibrium solid solution.7 The solvus slopes rapidly toward lower iron concentration, so that at 600°C only about 0.5 pct Fe remains in solution at equilibrium. Below the eutectoid temperature (850°C), the iron-rich phase in equilibrium with the copper-rich solid solution consists of body-centered-cubic a-Fe. Above 850 °C the equilibrium iron-rich phase is face-centered-cubic r-Fe. The alloy to be studied was made by melting electrolytic iron and OFHC copper by induction under vacuum in an Alundum-lined crucible. The metal was held molten for about 5 min, after which time the power was turned off and the crucible was tipped about 70" to promote directional solidification. The resulting ingot, containing 2.5 wt pct Fe by analysis, was clean, large grained, and free of gross segregation. Slices % in. thick were cut from the ingot, rolled to 1/8 in. in thickness, homogenized in hydrogen at 1060°C for 24 hr and, finally, quenched in cold water. Specimens for all subsequent tests were made from these slices. Squares measuring about 1 cm on a side were cut from the slices to make specimens for studying hardness and microstructure. Wires (0.020 in.) for the Debye-Scherrer survey were drawn from 1/8 in. sq rods which had been cut from the homogenized slices. Large crystals for observing diffuse X-ray diffraction effects were prepared by mechanically

Jan 1, 1958

By D. W. Loughridge

INTRODUCTION Raising capital in the 1990s is a timely subject. However, many of us thought why should raising capital in the 1990s prove to be unlike it was in the 19805, the 1970s, the 1%0s, or earlier? There are a lot of creative people in banking and in corporate treasury departments. New tools and techniques are continuing to emerge, many of which are discussed in other papers in this book. While we have new financing tools at our disposal, the underlying issue has not changed. Projects and investments must be judged on their own merits. If they cannot be justified by conventional financial analysis, they should not be built. If they can be justified, it is likely that the financing will be available. The challenges faced in raising capital in this decade will persist to the next. The issues of the 1980s -- currency fluctuation, disruptive merger and acquisition activity, commodity price volatility, political risk, and debt crisis -- will all persist in an increasingly international business environment. I will focus on the financing we have just completed for the Escondida Copper Project in Chile. The Escondida financing is structured along the classic project financing model developed in the late 1970s, but it deals with issues of the 1980s and the 1990s. The financing was intriguing, not just because of the technical issues involved, but also the challenge of reaching an agreement in a large and diverse group. Escondida had the one essential feature that made its financing possible. It was commercially very attractive. It would produce at low cost a commodity (copper concentrates) that direct consumers felt would be in tight supply. The project had the direct support not only of its sponsors, but also its customers, and, very importantly, its host government. The non- recourse financing of Escondida would not have been possible without the support of these parties, and without the robust economics that made this effort worthwhile. The issue was more complicated. Operations in all parts of the world entail some political exposure. This project is in Chile, where there was a constitutional requirement that a plebescite be held when the project would be in its early stages. This plebescite would determine the fate of a 15 year old military dictatorship. The project is copper, a commodity generally deemed to be in surplus. Copper has a history of price volatility (whose price has varied from $.58 to $1.53 per pound over the past two years). It is politically sensitive, not only in Chile, but in the United States, Canada and other developed countries. The project is international, with all the problems of dealing with a variety of currencies, a variety of cultures, and a variety of laws and commercial practices. The project is also large and capital intensive, with a total cost of U.S. $1.1 billion. ESCONDIDA PROJECT Escondida, the largest known copper ore body in the world, was discovered in March of 1981, by Utah International in a joint venture with Getty Oil Company. In 1984, both Utah and Getty were involved in ownership changes, Utah being acquired by BHP. A later restructuring of the ownership of Escondida resulted in BHP, as manager, carrying a 60% interest, Rio Tinto-Zinc Corporation (RTZ) 30%, and a consortium of Japanese companies led by Mitsubishi Corporation with 10%. The Japanese consortium is incorporated as JECO (Japan Escondida Corporation). This ownership structure, which spread ownership around the world, was the first tangible step toward managing both the commercial and political risk associated with the project.

Jan 1, 1990

By Carlos G. Valenzuela

The value generally accepted for stacking-fault energy, of copper has been approximately 40 ergs per sq cm based on Fullman's2 value for the coherent twin-boundary energy and the assumption that is twice the twin boundary energy However, Thornton and coworkers8 determined that the lower limit of for copper is approximately 60 ergs per sq cm, based on measurements of dislocation-node radii. They suggested that the assumption of = 2t is invalid. It is the purpose of this note to present results which indicate that the values of obtained by measurement of twin-grain boundary intersections and the values obtained by measurement of dislocation-node radii are actually compatible. The most reliable values for of the a brasses, based on electron-microscope observation of dislocation nodes, are probably those values reported by Smallman and Green6 who applied the Siems correction (1961) to data obtained by Howie and Swann.3 These values shown in Fig. 1 give an extrapolated value of approximately 70 ergs per sq cm for pure copper. In the present work, Fullman's method for determining the stacking-fault energy of copper was extended to the a brasses. High-purity copper (99.999 pet) and high-purity zinc (99.999 pet) were mixed in proportioned amounts and melted in sealed and evacuated quartz tubes. The alloys were homogenized for a week at 750°C and chemically analyzed by means of X-ray fluorescence. These alloys, along with a specimen of pure copper, were rolled to 98 pet reduction and a thickness of 0.009 in., resealed, and annealed for 40 hr at 715°C. Values for the ratio of twin-boundary energy to the grain-boundary energy, it gb, were obtained from measurements of dihedral angles formed at the intersections of twin boundaries and grain boundaries by using Fullman's2 mechanical analogy of surface tensions acting at the intersection of an annealing twin and a grain boundary. The angles between the twin traces and the grain boundaries were measured for a large number of twin-grain boundary intersections at a magnification of X500 using a rotating mechanical stage on a Reichert metallograph. The rotary stage has a calibrated angle scale with vernier so that measurements can be made to 0.1 deg. The mean twin-grain boundary energy and standard deviation were calculated for copper and each of the brasses by the use of an IBM 7072 computer. It was found that the mean value of gb stabilized after approximately 100 twin-angle measurements. This was determined by plotting the mean against the number of angles measured. Since the measured angles deviate from true dihedral angles, a correction factor for grain orientation, discussed below, was applied. The stacking-fault energy was then calculated from these values and the values of grain-boundary energy derived by Taylor.7 The data obtained are tabulated in Table I. Values for stacking-fault energy are plotted in Fig. 1. The value of gb for the specimen of 1.03 pet Zn is close to the value obtained by Fullman2 for OFHC (99.98 pet) copper, 0.045. It is believed that the purity of the copper affects gb significantly. The 99.999 pet purity Cu used in this investigation yielded a value of yt/ygb, 0.76, which is much higher than that obtained by Fullman. Additional evidence suggesting that the purity of

Jan 1, 1965

By D. W. Akins

The case history of a combination gas and water flood instituted early in the life of a field is described. It was recognized from the beginning that recovery would be low, under normal production methods, from the several separate, thin beds of porous limestone which had such poor native permeability that the wells would not produce without acidizing. It is thought that the combination flood gives excellent recovery efficiencies for this type of reservoir. The chief function of the gas flood now is to maintain bottom hole pressure in that part of the reservoir which will not be affected by the water injection program until later. Present estimates are that ultimate recovery will be approximately double the recovery expected under the original solution gas drive mechanism. Wide (80-acre) spacing has enhanced the economics of the over-all field program by the elimination of more than $5,000,000 worth of unnecessary wells. INTRODUCTION The Haynesville Pettit Field was discovered in November, 1941, with the completion of T. L. James Co.'s Callie Akin No. 1, located in the W 1/2 of the NE 1/4 Section 27-23N-8W, Claiborne Parish, La., at an approximate depth of 5,300 ft. The center of the field is about two miles north and a mile west of the town of Haynesville, La. A total of 189 producing wells have been drilled on 14,500 acres. An additional nine dry holes were drilled. The Louisiana-Arkansas state line divides the field so that 34 wells are in Arkansas and 155 are in Louisiana. Governmental sections are divided equally to contain eight production units making 80-acre spacing where the sections are regular. Along the state line in Louisiana there is an irregular tier of sections, each of which contains approximately 456 acres. When divided equally into eight production units the spacing is 57 acres per well for these three and a fraction productive sections. All Haynesville Pettit wells are identified by their section number followed by their position in the section as determined by numbering the production units counterclockwise beginning in the upper right corner of the section. All of the producing wells in the field except two are unit-ized and operated by the Haynesville Operators Committee. These two wells are located in the extreme northern part of the field in Arkansas. Efforts to bring them into the Unit are being continued. The Pettit operators organized the Haynesville Operators Committee and the field became a unit operation May 1: 1944. GEOLOGY The Pettit is Lower Cretaceous in age and is defined as the uppermost porosity in the Sligo formation. The unitized area known as the Haynesville Pettit Field is composed of two separate zones of porosity approximately 40 ft apart and without connection between the two, except in wells. These zones are known as the Upper Pettit and the Lower Pettit. The Upper Pettit is separated into two sections throughout most of its area by a relatively thin but quite impervious shale streak. These are called the "A" and "B" sections of the Upper Pettit. All of these lenticular zones are composed of coquina limestone and a small percentage of normal oolites. The large

Jan 1, 1951

By D. W. Akins

The case history of a combination gas and water flood instituted early in the life of a field is described. It was recognized from the beginning that recovery would be low, under normal production methods, from the several separate, thin beds of porous limestone which had such poor native permeability that the wells would not produce without acidizing. It is thought that the combination flood gives excellent recovery efficiencies for this type of reservoir. The chief function of the gas flood now is to maintain bottom hole pressure in that part of the reservoir which will not be affected by the water injection program until later. Present estimates are that ultimate recovery will be approximately double the recovery expected under the original solution gas drive mechanism. Wide (80-acre) spacing has enhanced the economics of the over-all field program by the elimination of more than $5,000,000 worth of unnecessary wells. INTRODUCTION The Haynesville Pettit Field was discovered in November, 1941, with the completion of T. L. James Co.'s Callie Akin No. 1, located in the W 1/2 of the NE 1/4 Section 27-23N-8W, Claiborne Parish, La., at an approximate depth of 5,300 ft. The center of the field is about two miles north and a mile west of the town of Haynesville, La. A total of 189 producing wells have been drilled on 14,500 acres. An additional nine dry holes were drilled. The Louisiana-Arkansas state line divides the field so that 34 wells are in Arkansas and 155 are in Louisiana. Governmental sections are divided equally to contain eight production units making 80-acre spacing where the sections are regular. Along the state line in Louisiana there is an irregular tier of sections, each of which contains approximately 456 acres. When divided equally into eight production units the spacing is 57 acres per well for these three and a fraction productive sections. All Haynesville Pettit wells are identified by their section number followed by their position in the section as determined by numbering the production units counterclockwise beginning in the upper right corner of the section. All of the producing wells in the field except two are unit-ized and operated by the Haynesville Operators Committee. These two wells are located in the extreme northern part of the field in Arkansas. Efforts to bring them into the Unit are being continued. The Pettit operators organized the Haynesville Operators Committee and the field became a unit operation May 1: 1944. GEOLOGY The Pettit is Lower Cretaceous in age and is defined as the uppermost porosity in the Sligo formation. The unitized area known as the Haynesville Pettit Field is composed of two separate zones of porosity approximately 40 ft apart and without connection between the two, except in wells. These zones are known as the Upper Pettit and the Lower Pettit. The Upper Pettit is separated into two sections throughout most of its area by a relatively thin but quite impervious shale streak. These are called the "A" and "B" sections of the Upper Pettit. All of these lenticular zones are composed of coquina limestone and a small percentage of normal oolites. The large

Jan 1, 1951

By D. A. Thomas, E. S. Meieran

Tungsten wires were examined by transmission electron microscopy after drawing and after high-temperature annealing. Drawn wire consists of highly elongated grains called fibers, whose long axis is parallel to [110]. Each fiber is ribbon-shaped, with the wide dimension of the ribbon parallel to (001) and the narrow dimension parallel to (110). Furthermore, most fibers are bent about [I10] and twisted along their length. The fibers are divided into cells, which in some cases contain a platelet substructure lying on (110) planes. The misorien-tations of these platelets accumulate to allow the macroscopic twist of the fibers. During annealing, several competing reactions occur, starting at different temperatures and progressing at different rates. Among these processes are fiber-boz~ndary migration, polygonization, dislocation rearrangement, and possibly impurity segregation. The fiber-boundary migration accompanied by the formation of transverse boundaries during polygonization leads to an equiaxed grain structure although recrystal-lization does not occur. There is a relationship between the flow stress of the wires and their average subgrain width in the form sy = s0 + kyd-1/2 . Also, there appears to be a relatio'nship between wire ductility and the formation of transverse boundaries during annealing at about 800°C. THERE have been many investigations of the structures and properties of tungsten wires1-4 due to their commercial importance for use as lamp filaments. The structural studies have so far been limited to optical microscope and replica electron-microscope studies. due to the difficulty of .-me- paring from wires thin foils which can be examined by transmission electron microscopy. However, this difficulty has been recently overcome,5 and it is now possible to examine tungsten wires by transmission electron microscopy as well as by other techniques. In this paper, the structure of drawn tungsten wire is described, as are the changes in the structure during high-temperature annealing. Some discussion of the relationship between structures and properties is also given. EXPERIMENTAL MATERIALS AND PROCEDURES Commercial 0.030-in.-diam doped tungsten wires drawn at progressively decreasing temperatures between about 1400° and about 800°C were examined. The composition, mechanical properties, and optical microstructures are described in detail elsewhere.' All experimental materials were vacuum-annealed for 10 ot 30 min at temperatures at 100°C intervals between 700° and 2000°C. Specimens were thinned for examination in the Siemens Elmiskop I electron microscope by the method of Meieran and Thomas.5 STRUCTURE OF AS-DRAWN WIRE The optical microstructure of as-drawn tungsten wire has been described by Peck and Thomas.7 They observed that wire in longitudinal section consists of highly elongated grains called fibers whose width varies between 1 and 10 µ, while in transverse section the fibers appear to be elliptical in cross section and bent about their common [110] wire axis. They explained this unusual appearance as being due to the drawing of a bcc material with a [110] texture, and predicted that the wide and narrow planes of the fiber cross section would be parallel to (001) and (110), respectively. The fibers apparently bend about the [110] axis during drawing to maintain grain boundary continuity during drawing. Transmission electron microscopy offers a way of checking these predictions as well as providing a more detailed picture of the wire structure. Figs. 1, 2, and 3 are typical electron micrographs of

Jan 1, 1965

By Ralph H. Sweetser

C. H. Herty, Jr.,* Pittsburgh, Pa.—The procedure of the Open-hearth Committee in studying pig iron and its effects in the open hearth has been influenced by the discussions at a number of meetings of the Committee. Those discussions have brought out very clearly that, as far as the pig iron affects the quality, interference with quality should be studied for three definite types of pig iron: (1) low-silicon pig iron; (2) very high-silicon pig iron, and (3) pig iron in which the silicon varies over a wide range in short periods, such as 1 to 3 casts. If a blast furnace is running steadily at 1 per cent. silicon iron, practically no trouble, apparently, can be traced to the pig iron, but if the furnace is running from 0.60 up to 1.50 and then down to 0.60 per cent., trouble in the finished steel is liable to occur, which apparently cannot be corrected by open-hearth practice. The open-hearth discussions have shown fairly definitely that with low-silicon iron, one type of trouble arises on the finished product and with the high-silicon iron, another. Our experience with the high-silicon is that any non-metallic matter that may form, does so when the pig iron is put into the furnace; that is, silicates immediately form which are more liable to be high in silica than would happen with low-silicon iron. I think Mr. Sweetser will agree with mc that if a blast furnace is very irregular, different points in the furnace may be working irregularly, in other words, the temperature gradient all over the furnace is not uniform. We have made many determinations on that point which indicate that a varying blast furnace causes hot spots and cold spots around the periphery. If some of those spots are hot and others are cold, although the analysis of the iron may be constant, then unreduced oxide, going through on one side, and good iron, going through on the other, may mix and the average temperature of the iron is not high enough to get completely rid of the oxides. So our method of attack is directly on that point; it is our first objective. Our procedure is to make a number of consecutive tests at a blast furnace, making a detailed study of the blast-furnace operation. We follow the iron through the open-hearth heat, being sure that we know just how much of each kind of iron gets into the open hearth, and take out specified samples at certain times during the process, working on steel where no finishing additions are made in the furnace. We are following one type of iron through the billet mills and into the finished product and are obtaining complete data on open-hearth operation. Besides the ordinary chemical analyses on the samples of slag and metal, we are running samples of the plg iron, the steel in the open hearth and the finished steel, for oxygen and silicates. We are going to find out whether or not oxygen, as silicates or oxides, has some connection with this trouble. If not, we may be able to locate some other factor. I am inclined to think that the silicates are responsible, judging from the indications in some other work that the Bureau of Mines is doing in Pittsburgh. We have laid out a very definite method of testing to which we will adhere at the different plants where we are now working and at others in the future. Our aim is to

Jan 1, 1927

By William P. Roe, James F. Ellis, W. P. Fishel

This paper reports the distribution of sulphur between iron and titanium in Fe-Ti-S alloys and in Fe-Ti-C-S alloys. The compound TiS was found, which exists as a separate phase at temperatures below 1200°C. Titanium in steels reacts with sulphur in preference to carbon. THE general relationship between sulphides and oxides suggests that titanium should form a sulphide having properties similar to those of titanium oxide. Specifically, titanium should form a sulphide having a high melting point, indicating a stable compound of low solubility in iron. In order for titanium to function as a desulphurizer or sulphur-fixing agent, it must form a stable sulphide. In order for titanium to be useful in steels as a sulphur-fixing agent, it must react with sulphur in preference to carbon; and to prevent red shortness, the sulphide formed must have solubility characteristics such that grain-boundary precipitation of a low melting phase be prevented. The terms desulphurizer and sulphur-fixing agent when used in this paper mean that titanium effectively ties up the sulphur as a stable sulphide of titanium and prevents the formation of FeS. The partition of sulphur between iron and titanium was studied first in a series of Fe-Ti-S alloys with carbon absent, and then in similar alloys with carbon present. It has been established1 a that titanium forms in Fe-Ti-S alloys a sulphide of undetermined composition which can be identified microscopically, and that the titanium-sulphur compound does not respond to sulphur printing. It has been suggested" that titanium acts as a sulphur-fixing agent, although little proof has been given. A report% f The Advisory Committee on Metals and Minerals summarizes the existing knowledge concerning substitutes for manganese in steels. Distribution of Sulphur Between lron and Titanium with Carbon Absent The alloys for this investigation were made by -melting Armco iron, metallic titanium, and iron sulphide in alundum crucibles in an induction furnace. The titanium was added after the other ingredients had melted. In these alloys it is recognized that some TiO, is present, since the melts were made in the air and since no other deoxidizing agent was used; therefore, some of the titanium was not available for union with sulphur. Thirteen ingots were made. Ingots 2 to 8 were cast in baked-sand molds; ingots 12 and 13 were cast in metal molds; and ingot 9 was allowed to cool in the crucible in which it was melted. All ingots were annealed at 900°C for 3 hr and were cooled slowly in the furnace. Subsequent information indicates that this anneal had no effect upon the titanium sulphide particle size, since the sulphide does not go into solution at this temperature. The ingots as-cast were approximately 8 in. long and % in. diam. The compositions of the eight ingots and the results of the partition of sulphur are recorded in Table I. Total titanium and total sulphur were determined by standard gravimetric methods. Sulphur, as iron sulphide, was determined by the evolution method. Boiling HC1 (1:4) liberates the sulphur from iron sulphide, but leaves the titanium sulphide practically undecomposed. A complete separation of titanium sulphide and iron sulphide cannot be made by digesting these compounds in dilute HC1 since titanium sulphide was found to dissolve slowly. The amount of titanium sulphide decomposed will depend upon the time in contact with the acid and upon the particle size of the sulphide. The point

Jan 1, 1952

By A. P. Pipilen, M. Weintraub, W. F. Hosford, A. A. 230-000-000-006 Orning

In a study of the principal factors affecting the transport of coal-water mixtures through a centrifugal pump and a pipeline, the interrelation between solids concentration, velocity, and pressure drop was established for a minus 2-in. bituminous lump coal in concentrations up to 48% by weight. Optimum concentrations were found to exist for maximum capacity of a given pipeline and for minimum energy requirements per ton of coal. Coal size degradation by particle fracture took place in the pump; abrasion and attrition to form fines took place in both pump and line. A novel system of studying flow of solid-liquid mixtures in pipelines by the determination of relative sound intensities was developed. The hydraulic transport of minerals is in part an established art and in part a relatively new field of industrial technology. The established art developed especially where the mineral was under water, where water was used in hydraulic mining, or where large quantities of water had to be pumped from the mining site to expose the mineral. Power requirements and limited life of pumps and pipelines, under such conditions, were relatively unimportant. Examples may be found in dredging, and in hydraulic mining and transportation of phosphate rock.' In the design of a coal pipeline the most needed information relates to flow characteristics, power requirements, pressure drop, size degradation, and size segregation as a function of solids-water ratio and size distribution of the mineral. A considerable amount of information has become available concerning pressure drop and energy requirements.2'3 These topics were therefore not studied intensively. Coal degradation, however, has not been clearly delineated. Lammers and coworkers4 showed that coal may be severely degraded in size but did not distinguish between degradation produced in the pump and in the line. It is the primary purpose of this paper to outline techniques used to acquire some of the much needed design data. A full report of the investigation is to be published by the Bureau of Mines at a later date. APPARATUS AND PROCEDURE The apparatus for circulation tests (hereafter referred to as Type III tests) consisted essentially of a loop and a centrifugal solids handling pump, with attendant instrumentation, and coal weighing and feeding equipment. It also included an adequate water supply, as shown in Fig. 1. The selection of 6-in., schedule 40, carbon steel pipe was based on the top size of coal to be used. Assuming that the top size of coal should not exceed 1/3 the inside diameter of the pipe, a 6-in. pipe would accommodate 2-in. coal, a realistic size for transport from the mine face. An 872-ft loop was constructed first. Later a few tests were made with a lengthened circuit of 1361 ft by superimposing an additional loop on the original one. All bends used were of 3-ft radius. A noisemeter microphone, taped to the pipe at various points, but generally about 50 ft downstream of the pump, was used to sense segregation of the coal and the length of slugs of coal in water. To measure the stream velocity, radioactive sources were encapsulated in plastic cubes. The specific gravity of the blocks was adjusted to 1.3 and 1.8 to simulate low ash and high ash coal particles. Their passage through the pipeline was detected by a Geiger counter. Because the repeated circuits of the Type III tests did not permit coal degradation in the line to be distinguished from that produced by the pump, the two

Jan 1, 1964

By H. J. Beach

This paper describes the properties and uses of cementitious mixtures containing 10 to 20 per cent bentonite and 2 per cent or more sodium chloride. Salt additions improve bentonite cement by increasing early strength and stabilizing viscosity without changing thickening time. The volume yield of cement is increased 20 per cent or more without lowered early strength. The unique properties of salt in this type of system make savings of more than 10 per cent possible where light-weight, low-strength cementitious material is adequate to fill behind pipe. The density range of these mixtures is 12 to 13 1b/gal and the filtration rates are medium-low, aiding the placement of long columns in primary cementing. Where available, sea water is an ideal salt source in preparing these slurries. INTRODUCTION Accelerators increase the rate of cement hydration. In speeding reaction with water, they can affect cement performance by reducing thickening time and increasing early strength after set. Accelerators that cause both effects can be considered "total", and those which produce only one effect can be called "partial". Materials that act conversely to accelerators are retarders. and they also can be total or partial. Partial retarders. make high-temperature cementing possible by prolonging thickening time while impairing early strength only slightly. Most known accelerators are total. A useful partial accelerator would increase strength without altering thickening time. This report concerns material combinations in which a normally total accelerator exerts unique partial properties. Utilizing these limited effects improves bentonite cement. SEPARATE EFFECTS OF SODIUM CHLORIDE AND BENTONITE ON CEMENT Sodium chloride and calcium chloride are commonly used in cement, and at low concentrations their effects are similar. Ludwig1 studied sodium chloride in API Class A and Class E cements.' Figs. 1 and 2 sum- marize his data taken at 140°F on slurry pumpability and early strength. Normal water-to-cement ratios are 0.46 and 0.40, respectively, for Class A and Class E cements. At saturation the salt content is 12 to 14 per cent of the weight of cement solids. The illustrations, therefore, cover the range of salt solubility in the mixing water. The data show that sodium chloride is a total accelerator of the Class E cement studied over the range of solubility. It is total in Class A cement to 6 per cent. Above this concentration salt becomes a retarder— partial from 6 to 10 per cent and total above. These results are general for different brands of Class A cement, although the shift from acceleration to retardation may occur at different salt concentrations for different temperatures. The results are specific for the Class E brand studied. In discussing his data, the investigator emphasized that different Class E cements might respond erratically to salt, depending on the brand chosen. Morgan and Dumbauld3 escribe the properties of bentonite cement in a paper that is a standard reference in using these systems. Bentonite functions in cement as an enabling agent; each bentonite addition equal to 1 per cent of the weight of dry cement makes possible the further addition of 4.5 per cent water.' Thus, 10 per cent bentonite in Class A cement, normally slurried neat with 46 per cent water, enables the slurry to contain another 45 per cent before settling. Water is one of the lightest and cheapest cement extenders; it reduces density and cost. Bentonite cements produce uniform slurries having low susceptibility to solids separation. After set, they offer low resistance to perforation.

By J. G. Y. Chow, S. B. McRickard

The tensi1e properties of Ferrovac iron have been studied from 4° to 300°K. The stress required for macroscopic yielding was found to he constant below approximately 50°K. The effect of mechanical twinning on this low -temperature stress plateau was investigated. The onset of twinning occurs in this iron between 130° and 150°K and depending on its previous thermal history the twinning-stress curue may drop below or remain above the vield-stress curves as the temperature is lowered. Twinning has been shown to initiate slip in quenclzed iron at low temperatures. In no instances, however, did the onset of twinning alter the continuity of the yield stress -tempwature curve. Our data shows that carbon inhibits twinning and slip at low tem-peratures. This observation nay be used to explain the ductile-to-brittle transition in iron. The effect of fast neutron irradiation on yielding and embrittlement in iron and Fe-C alloys is offered as supporting evidence for this viewpoint. THE mode of yielding in iron at low temperatures was studied in an attempt to find an expression based on a single mechanism to describe the thermal dependence of the yield stress of iron. There are two types of inflections observed in the variation of the yield stress with temperature in iron and Fe-C alloys. The first is associated with ductile behavior and consists of a region extending 50" to 100°K above absolute zero in which the yield stress is independent of temperature. The second is observed in more brittle materials such as Fe-C alloys and irradiated iron and consists of an abrupt discontinuity in the yield curve as the temperature is lowered through a ductile-to-brittle transition point. The temperature dependence of the yield stress for iron with four grain diameters as found in this study is shown in Fig. 1. To varying degrees all the curves appear to flatten or approach an asymptotic value as the temperature is lowered below 50°K. Several other investigators1,2 have observed a plateau in the yield stress of iron and steel at low temperatures and in 1956 Louat3 presented a theory which contained an explanation for this behavior. In a subsequent exchange with Erickson and Low4'5 who attributed the plateau to the onset of mechanical twinning Louat8 showed that twinning first occurs in iron and steel tested in tension at temperatures as high as 140°K which is well above the observed plateau in yield stress. Furthermore he pointed out that both twinning and slip are basically dislocation processes and that with modified parameters his original theory still applied when deformation is initiated by twinning. Variables which affect the ductile-to-brittle transition in iron are test temperature, strain rate, composition and grain size.7 LOW,8 Hahn et al.,9 and Hull10 have provided evidence which links brittle fracture at a given temperature with the specimen grain size and the onset of twinning. In fact, Hull equates the brittle fracture stress to the twinning stress. On the other hand brittle fracture has been observed in the absence of twinning and priestnerl1 has given a fracture criterion which is valid whether or not fracture is preceded by extensive twinning. The data presented here clarify the role of twinning in the low-temperature deformation of iron. Strong evidence is given that the amount and distribution of interstitial impurities such as carbon are of

Jan 1, 1965

By Pedro Bolsaitis, Paul M. Sullivan

The activities of zinc in liquid Zn-A1 alloys in the temperature range of 1000' to 1160°K were determined by means of the isopiestic technique. The results are in reasonable agreement with the previous values determined by the radioactive tracer dew point method. Slightly negative excess entropies of mixing were found. The measured activities suggest that the a function for these alloys is not a constant, as has frequently been assumed, but is better represented by two straight line segments of different slopes. THE thermodynamic data of Al-Z alloys have been the subject of investigation by many authors. However, in the recent compilation of such data by Hult-gren et al.,5 the conclusion is reached that none of the previous measurements are reliable or consistent with each other. Since then two new sets of measurements have been reported,2, 8 both laying claim to good accuracies, yet showing very significant disagreement in the measured activity coefficients of zinc in Zn-A1 alloys and in the magnitude and sign of the excess entropies of mixing. Information on the thermodynamics of the system is of particular interest for interpreting results of the Bureau of Mines research on refining of zinc by distillation of die cast scrap. The present study was undertaken as an independent check on the recent values obtained from dew point measurements 8 and electromotive force measurements.' The isopiestic method, first introduced by Herasy-menko,' was chosen because it is one of the few thermodynamic techniques which, in principle at least, is carried out under perfect equilibrium conditions. The disadvantage of the method is that data are obtained at various random compositions and temperatures, which makes the interpretation somewhat cumbersome. The random errors arising from temperature gradients and fluctuations appear to be comparable to those of other techniques, as evidenced by the magnitude of the estimated uncertainties in the calculated integral thermodynamic quantities. An advantage of the method is that each run provides a relatively large amount of data; thus, it is less time consuming than those methods where samples of each composition must be measured individually. EXPERIMENTAL PROCEDURE The activities of zinc in liquid Zn-A1 alloys were measured by the isopiestic method which uses the principle of the tendency toward equilibrium of a series of samples at various temperatures under an imposed vapor pressure of the more volatile component (i.e., zinc, in this case). The basic apparatus is shown in Fig. 1. The small graphite crucibles that contained the metal samples were 15 mm ID and 13 mm deep with approximately 3 mm wall thickness. Each crucible was notched at the top and bottom to allow easy passage of vapor from one to another. At the beginning of an experiment each crucible was weighed on an analytical balance. Zinc and aluminum of spectrographic purity (99.999 pct) were then weighed into the crucibles. The amounts of each metal added were such that initial compositions varied above and below equilibrium values. One crucible contained only pure zinc. After weighing, the crucibles were stacked with the pure zinc on the bottom (corresponding to the lowest temperature in the furnace) and richest aluminum alloys at the top. The entire stack of crucibles was then placed in the silica glass container "E" which was then sealed under vacuum. Sixteen to twenty calibrated Chromel-Alumel thermocouples were attached by wire along the length of the silica tube, one or more adjacent to each sample.

Jan 1, 1970

By W. L. Phillips

Nickel alloys containing approximately 0.5, 2.0, and 6.0 at. pct of Os, Pd, Ru, and Rh were Prepared by vacuum melting. Tension tests were carried out at 25°, 500°, 800°, and 1000°C; stress-rupture tests were carried out at 650° and 800°C. The room- and elevated-temperature tensile strength, as well as the stress-rupture life, increased for the same atomic percent in the order palladium, rhodium, ruthenium, osmium. The ductility decreased with increasing concentration or temperature for a given concentration. The results are discussed in terms of solid-solution theory. BOTH solid-solution strengthening and weakening have been observed in alloys. The simple rules which have been suggested to explain alloy strengthening are subject to several exceptions and deviations based on atom size and valency effects. The purpose of the present investigation was to extend the knowledge of the effect of solid-solution alloying on the mechanical properties of several Ni-Pt group metal alloys at room and elevated temperatures. The platinum group metals, osmium, ruthenium, rhodium, and palladium were chosen as the solute elements because of their different valencies and atom sizes. Nickel was chosen as the base material because of the large amount of previous literature available on nickel alloys. EXPERIMENTAL PROCEDURE Grade A Carbonyl nickel powder having the following composition: C, 0.07 pct; Fe, 0.013 pct; Mn, 0.0005 pct; Si, 0.016 pct; Mg, 0.0003 pct; S, 0.003 pct, was purchased from the International Nickel Co. The platinum-group metal powders were purchased from A. D. Mackay Co. The powders were weighed, cone-blended for 4 hr, and vacuum-melted into 1-in.-diam billets, approximately 2 in. long. The ingots were homogenized for 5 hr at 1800°F before being extruded into 1/4-in. rods at 2100°F. The alloy compositions are shown in Table I. Typical impurity values were not significantly different than that of the as-received nickel. All alloys were single phase. The lattice parameter of each alloy after the heat treatment described below is also included in Table I. Each alloy was annealed at 2200°F for 1 hr and air-quenched to comparable grain sizes (ASTM G.S. No. 4-5). The rods were then machined into test samples 0.160-in. diam and 0.750-in. gage length. Tension testing was carried out in an In-stron tension-testing machine at a strain rate of 0.02 in. per in. per min. An extensometer was used to determine the room-temperature yield stress. Stress-rupture testing was carried out in an Arc Weld stress-rupture unit. All testing was performed in air. EXPERIMENTAL RESULTS A) Room-Temperature Mechanical Properties. The 0.2 pct yield stress, ultimate tensile strength, and elongation for all alloys tested at room temperature are plotted as a function of atomic percent solute element in Fig. 1. The ultimate tensile strength for the same atomic percent increases in the order palladium, rhodium, ruthenium, osmium. The yield strength at low concentrations, -0.5 at. pct, increases in the order osmium, palladium, ruthenium, rhodium. At higher concentrations, 3.0 and 10.0 pct, the yield strength increases in the same order as the tensile strength. Both yield strength and tensile strength increase rapidly ini-

Jan 1, 1964

By D. G. Westlake

NUMEROUS hydride habit planes in zirconium, Zircaloy-2, and Zircaloy-4 have been observed by various researchers and have been compiled by Louthan and Angerman.1 While only partial agreement exists on the identification of these habit planes, there is a growing consensus that a tensile stress applied on a polycrystalline rod during slow cooling will cause the hydride platelets to lie perpendicular to the tensile axis. walters2 agrees with Louthan and Angerman who reason that "The particular plane on which precipitation will occur is the plane that will result in the maximum relief of stress by precipitation of the low-density hydride." The experiment described below was initiated to test this hypothesis on a single crystal of zirconium. A single-crystalline tensile specimen of zone-refined zirconium, designated number 13 in a previous study,3 had a square cross section with one pair of parallel faces only 4 deg from the basal plane of the hcp structure. The tensile axis was about 86 deg from the (0001) pole, 14 deg from the (1010) pole, and 16 deg from the (1150) pole. The specimen was charged to 50 ppm H by allowing reaction with the correct amount of hydrogen at 1073°K, homogenizing at this temperature for 2 hr, and cooling in the furnace. Two- surface analysis revealed that hydride platelets had precipitated parallel to the three {1010} prism planes. The specimen was heated to 673°K, in air, for 16 hr to bring the hydrogen back into solid solution, and furnace-cooled to 573°K.* It was then stressed in ten- sion at 1.2 kg per sq mm. (This produced a resolved shear stress of 0.6 kg per sq mm for glide on the prism plane with the highest Schmid factor. A higher stress would have produced significant strain at this temperature because the critical resolved shear stress for prism-plane glide in this crystal was only 1.0 kg per sq mm at ambient temperature.) The poles of the three prism planes were at angles of 14, 46, and 74 deg to the tensile axis so that an applied stress would exert normal stresses on the three planes in the approximate ratios 10:5:1, respectively. As soon as the stress was applied, the sample was furnace-cooled to room temperature. It was ground on wet Sic paper and chemically polished in 50 parts HNO3, 50 parts water, and 7 parts HF before examination. The result of the experiment was negative; i.e., the three (1010) planes were of equal importance as hydride habit planes.* It must be admitted that the ex- periment is not entirely comparable to those performed by walters,2 Louthan,5 and Louthan and Marshall6 on polycrystalline materials. They have found that some critical stress (below the macroscopic yield stress) is required for stress-orienting the hydrides. The applied stress in the present experiment was, by necessity, smaller by an order of magnitude than the critical stresses they report for the various materials. If the critical stress was related to the microstructure, one might postulate that it should be decreased by increasing the degree of perfection of the metal lattice and by increasing the grain size. But the experiment above suggests that, for the extreme case of a zone-refined single crystal of zirconium, the critical stress lies above that which one can apply without introducing gross plastic strain as another variable.

Jan 1, 1967

By C. H. Lee, R. Maddin

The diffusion rates of Ag110 in cylindrical single crystals of 99.99 pct pure silver, which were twisted to a total surface strain of 0.91 during the diffusion anneal at temperatures of 700°, 750°, and 800°C, were measured by sectioning and counting as a function of the strain rates. The ratio of the diffusivities while strain ing occurred (Ds) to those of the unstrained specimens varies linearly with the rate of twisting and attains values of near 100 for some of the rates used. The enhancement of diffusion by straining is inversely proportional to the temperature at which diffusion occurs. The activation energy for diffusion determined from the data plotted as a function of the rate of twisting decreases from 44,090 cal per mole for zero strain, to an asymptotic value of 21,000 cal per mole for the strain rates of 22 x it)"5 see-l. Qualitative explanation for the observations based on the generation of nonequilibrium number of defects by plastic deformation will be discussed. The initial research of Buffington and cohen1 on self-diffusion in a iron under compressive stresses contributed the first quantitative information concerning the effect of applied stresses on diffusion. These results were obtained from radioactive Fe55 plated on one of the horizontal surfaces and compressing the large-grained specimens while the diffusion-anneal was occurring. Enhancement of diffusion of a maximum of seventeen times was observed provided the strain was in the tertiary stage of creep and the rates of straining were at least as fast as rates used in the normal creep test. On the other hand, Darby, Tomizuka, and Balluffi,2 extending silver single crystals up to 30 pct elongation at rates of straining about equal to those used by Buffington and Cohen observed no effect. For the past two and a half years at the University of Pennsylvania, we have been investigating the effect or torsional strains on self-diffusion in silver single crystals. If enhancement is observed as has been reported1 a possible explanation may be based upon the generation of fairly large numbers of point defects and their role in the diffusion process. Hence, since torsion should produce an abundance3 of point defects, an increase in the diffusivity while the crystal is being twisted should easily be measured. EXPERIMENTAL PROCEDURE Our research uses single crystals of silver prepared from 99.99 Ag by the Bridgman method in a dynamic vacuum of less than 25 µ. As grown, they are about 25 cm long by 1.3 cm in diam. The crystals are cut into 7.5 cm lengths with a jeweler's saw and machined to the shape shown in Fig. 1. The test length of the crystal is machined to a 0.6 cm diam after which the ends are masked and the test section etched heavily in HNO3, and KCN:(NH4),S2Os , solution to remove the effects of machining. The specimen is then annealed in vacuum for 8 to 12 hr at 800°C to remove any residual stresses and also to recrystallize the end sections. The recrystallized ends are necessary since experiments showed that single-crystalline end sections are too soft to transmit the desired torque. Occasionally, recrystalliza-

Jan 1, 1960

By W. A. Backofen, B. B. Hundy

THE pole figure interpretation in a recent paper' on the torsion texture of copper was questioned in discussion,2 nd a simpler alternative interpretation was proposed. In the hope of reaching a positive decision in favor of one or the other, further studies were undertaken with 70-30 brass and Armco iron. This additional work has not answered all the questions about torsion textures, but the new pole figures do offer support for the original interpretation and show that the texture is more complicated than the alternative suggests. From the previous paper,' the appropriate method of describing the texture in a twisted bar is known to be a pole figure plotted on a plane tangent to the surface of the bar. The axes of the pole figure are chosen to coincide with directions in the tangent plane which are parallel and at right angles to the bar axis (the longitudinal direction, L.D., and the transverse direction, T.D.), for these directions define symmetry axes of the texture. Therefore any ideal orientation that might be selected to represent the texture gives the crystallographic plane parallel to the tangent plane and the crystallographic direction parallel to the axis of the torsion specimen. A unique texture was assumed in the original interpretation, and the four ideal orientations, (112) [111], (111) [112], (110) [001], and (112) [131], were used in its description. Of the four orientations, the first three provide possible slip directions along the direction labeled T.D. in the pole figure, which is one of maximum shear stress in a specimen being twisted. The alternative, however, simply considered the texture to be made up of two components, one a [Ill] alignment along the specimen axis with a random orientation about the axis as in the wire texture, and the other a superimposed orientation (110) [0011. Experimental evidence for this simpler interpretation was derived from two observations: 1—twisting did not alter the orientation of a single-crystal torsion specimen of a brass in which an octahedral plane was perpendicular (and a [Ill] direction parallel) to the axis, and 2—deformation bands with approximately the (110) [001] orientation were seen to develop in the crystal during the test. The new pole figures were obtained with a brass and an iron torsion specimen of 3/4 and 1 in. gage length diameter, respectively. After annealing, polishing, and twisting, seven rods, about 0.030 in. in diameter and with different orientations, were prepared from material near the surface of each specimen; these were required for the method of constructing pole figures by using a Geiger counter as developed by Norton.5 Since the shear strain gradient in plastic torsion is linear, it was readily computed that the material supplying the brass rods had been subjected to a shear strain of about 3.2, and that supplying the iron rods had received a shear strain of about 2. All details concerning specimen design, testing procedure, rod preparation, and use of the Norton technique can be found in ref. 1. Only this procedure was followed in working out the (111) and (100) pole figures for brass, Figs. 1 and 2. However, X-ray photograms were also involved in the construction of the (110) pole figure for Armco iron, Fig. 3. The photograms were made according to the conventional transmission diffraction technique using a small sheet taken parallel to the specimen surface and etched to a thickness of about 0.0025 in. They were especially important in locating the boundaries

Jan 1, 1954

By R. E. Carter, C. Wagner, F. D. Richardson

By means of inert markers of radio-platinum, it has been shown that cobalt metal oxidizes by out-ward diffusion of cobalt atoms through the oxide. Oxidation rates have been measured at various temperatures and oxygen pressures and have been found to agree with the rates calculated from the Wagner equation and the authors' values for the diffusion coefficient of cobalt in the oxide. The distribution of radio-cobalt in growing oxide loyers has been accurately measured and found to be different from that predicted from the Wagner oxidation theory. Attempts have been made to measure the change of lattice parameter of the oxide with composition. SEVERAL investigators have shown that cobalt metal oxidizes according to the parabolic law,1-3 but no detailed study has been made of the oxidation mechanism. Cobaltous oxide has a metal-deficient lattice, but the defect concentration which is dependent on the oxygen pressure is only approximately known.' From the similarities in the structures of "CoO" and "FeO" and the rate laws governing the oxidation of cobalt and iron, Gulbransen- as suggested that cobalt, like iron," oxidizes by diffusion of cobaltous ions through the oxide layer. To substantiate this hypothesis, he has attempted to measure the oxidation rate of cobalt as a function of the oxygen pressure but has been able to report only that the rate depends on a "small" power of the pressure. On the other hand, Preece," Valensi,' and Arkharov' all have suggested from indirect evidence that oxygen diffuses through the COO to the metal-oxide interface. The present authors, in a previous paper,' have shown that the rate of diffusion of cobalt in cobaltous oxide is dependent on the oxygen pressure. In that investigation, they also found that cobaltous oxide disks made by complete oxidation of cobalt metal were porous at their centers (Fig. 5L, ref. 4). Both these facts strongly suggest that oxidation of the metal proceeds via outward diffusion of cations. In order to establish the mechanism unequivocally, oxidation experiments were made with inert radioactive platinum markers, and the dependence of oxidation rate on oxygen pressure was measured. In addition, an attempt was made to determine the form of the cation vacancy gradient, which the marker experiment showed must exist across a growing oxide layer. This was done by depositing radioactive Co on the surface of a cobalt disk and then measuring the tracer distribution across the oxide layer produced by partial oxidation of the metal. Finally, an X-ray examination was made in an attempt to find the expected change of lattice parameter of COO with oxygen pressure. Experimental The apparatus and materials used were substantially the same as those previously described by the authors.4 Marker Studies: The use of inert markers to follow oxidation reactions was first attempted by Pfeil" in 1929, and radioactive markers have recently been used by Davies et al.' In the investigation reported here, the markers were applied as an (NH4)2PtCI6 slurry in several thin streaks across both faces of four disks of cobalt metal 1 mm thick and 14 mm in diameter. The disks were then oxidized almost to completion at 1200°C in pure oxygen. After oxidation, they were mounted and sectioned and auto-radiographs were taken to locate the markers. Oxidation Rate: The oxidation rate of cobalt was measured at 1148°C at oxygen pressures ranging from 0.0055 to 1.0 atm and at 1000°, 1148", and 1350°C under 1 atm of oxygen. The rate was deter-

Jan 1, 1956

By S. L. Couling, D. J-P. Adenis

i2) twinning in poly crystalline magnesium does not usually occur homogeneously but is concentrated in localized regions or bands inclined at about 45 deg to the stress axis. These bands of twinning are in many ways similar to the Luders bands seen in mild steel alzd Al-Mg alloys. Within a hand the percentage of the volume twinned may approach 100 with no twinning outside the band. Bands are not produced in specimens of grain size a3 x 10-= in. or in samples deformed at temperatures 300°F. Annealing of heavily twinned regions leads to re crystallization textures markedly different from those found in the starting material. The exact preferred orientation appears to depend on the starting grain size, the amount of compres-sive strain and the manner in which it is introduced. MAGNESIUM, with its hexagonal crystal structure, deforms plastically at room temperature by a variety of deformation mechanisms, one of the most important of which is (1012) twinning. In single crystals such twinning occurs on compression parallel to the basal plane or tension perpendicular to it. In wrought polycrystalline magnesium, such as rolled sheet, the preferred orientation is such that almost all the grains have their basal planes nearly parallel to the sheet surface. Therefore, if sheet material is deformed by cold rolling or by tension in the plane of the sheet, deformation of the grains by (1012) twinning is not favored. On the other hand, twins form readily on compression parallel to the plane of the sheet as in a compression test, on the compression side of a bent sample, or at the outer rim of a drawn cup. The first part of this paper deals with the morphology of (1012) twinning in polycrystalline magnesium. Some aspects of this subject were covered by Barrett and ~aller.' Of direct bearing on the work to be reported here are the comments of Jetter' in discussion to Ref. 1. He shows that Mg + 1.5 pct Mn alloy sheet when bent about a transverse axis develops a pattern of transverse bands on the surface of compression. A longitudinal section through the sheet shows that the bands are wedge-shaped and inclined to the rolling direction. The bands were identified as "outcrops of regions in which deformation is localized as the result of the reorientation brought about by (1012) twinning". The second part of the paper treats the recrys-tallization texture of the specimens twinned by compression. Magnesium deformed and then annealed generally recrystallizes with no change in orientation.1'3'4 This statement is true provided that the amount of (1012) twinning occurring during deformation is small. In an isolated observation, Anse15 has shown that, when deformation produces much (1072) twinning, annealing causes new maxima to appear in the pole figure. The second part of the paper elaborates on this point. I) MATERIALS AND PROCEDURES All of the experimental work to be reported was done using the commercial sheet and plate alloy AZ31B (nominal composition: 3 pct Al, 1 pct Zn, 0.4 pct Mn, balance magnesium). This alloy is available commercially in two tempers, -0 (fully annealed) and -H24 (partially annealed), and specimens of both tempers were used in various experiments. The average grain. diameter (AGD) for -0 temper 0.125-in. sheet is about 0.5 x 10- in.; where material of larger grain size was desired, anneals at elevated temperature were used to grow the grains. compression tests were made on a screw-driven "hard" machine. The specimens were clamped in a

Jan 1, 1964

By Paul J. Bennett, James E. Castle

The sillimanite family of minerals, including kyanite, sillimanite, and andalusite, are anhydrous aluminum silicates with the formula A12O3-SiO2. Dumortierite and topaz are also included in this group because they are closely allied in composition and thermal behavior. However, neither are mined commercially today. They are typical metamorphic minerals which are found in metamorphic rocks on every continent. Sillimanite minerals are prized chiefly for their refractoriness and are important components in a broad range of acid refractory products, especially in mortars and castables. World production of sillimanite minerals is currently about 400,000 tpy and has been increasing at the rate of 3 to 8% a year for many years (Anon., 1972). While these minerals have widespread occurrence, the consumption of sillimanite minerals is concentrated in the relatively few highly industrialized areas where refractories are manufactured, and which in turn are typically close to the major iron and steel producing regions of the world. Thus northern Europe,. England, the United States, and Japan are the principal consumers of refractories and sillimanite minerals. Of these countries only the US is a significant producer. Uses of Kyanite The following specifications are typical for the domestic kyanite industry: Raw Kyanite Concentrates Chemical Analysis 56% AI2O3 min 0.1% CaO max 42% SiO2 0.1% MgO max 1% Acid soluble 0.3% combined Fe2O3 alkali max 1.2% TiO2 max Available Sizes 35, 48, 100, 200, and 325 mesh The largest use for domestic kyanite, both raw and calcined, is in the manufacture of refractory mortars, cements, castables, and plastic ramming mixes. In these applications kyanite constitutes from 10 to 40% of the mixture, the balance being refractory clays and coarser grog materials. A certain proportion of raw kyanite is used to offset the shrinking of the clay binder, whereas the calcined kyanite is used in the coarser sizes for body. Certain high grade refractory shapes and kiln furniture are composed chiefly of graded sizes of calcined kyanite bonded with a little ball clay. In most applications, however, kyanite is used only to fortify the mix or as a minor ingredient. Some manufacturers of mullite brick use domestic calcined kyanite for the fine-grained portion of the brick, but seldom in quantities exceeding 10% by weight. Kyanite is used by ceramic manufacturers of wall tile and sanitary ware to offset shrinkage and cracking after firing. Indian kyanite has traditionally been used to make the coarse grog sizes needed for the manufacture of mullite brick, and for the grog portions of mortar, cement, and castable mixes. It has been largely replaced, however, by synthetic mullite, high fired flint, and diaspore clay or calcined bauxite for other applications. Indian kyanite has been available in lump as well as in granules and concentrates, as are sillimanite materials from India and South Africa. Andalusite is available as 8 mesh granules and as fines with chemical analyses not unlike those of domestic kyanites. From time to time and from place to place minor amounts of other aluminum silicate minerals such as dumortierite, topaz, and pyrophyllite have been made available at various prices and specifications, but have not been significant factors in the refractory industry. A mixture of kyanite and sillimanite of relatively fine grain-size and of low iron content was at one time offered to the molding sand industry by the Du Pont Co. as a byproduct from their deposits of heavy

Jan 1, 1983

By Jean-Jacques Prompsy, J. S. Rinehart

The purpose of the present study was to arrive at a better understanding of the stress fields developed within drill bits under dynamic loading and the influence that these stress fields could have on the failure of the drill bits. Particular emphasis has been given to the influence that bit shape has on the establishment of highly localized, potentially destructive stress inhomogeneities within the bit. This paper covers one phase of a broad study involving three velocity regimes: impacts at very low velocities, 0 to 20 ft/sec, a velocity range in which dynamic effects are just beginning to be found; impacts at velocities ranging from 20 to several hundred ft/sec, arange commonly encountered in practical drilling operations; and impulsive loading through the detonation of explosives, a velocity range in which the dynamic effects are greatly exaggerated and made more identifiable. Specifically, fracturing which develops at the end of a cylindrical bar undergoing a shock produced by impact was experimentally investigated, the impacted area being the face of a truncated cone terminating the cylindrical bar. Fracture characteristics were looked at as a function of impact velocity, area of impacted face and cone angle — parameters of considerable importance in the design of drill bit. EXPERIMENTS The specimens were made of Plexiglas, which enabled the fracture pattern to be easily observed. In Plexiglas, the velocity of a longitudinal wave is about 8,700 ft/sec, and the velocity of the transverse wave about 4,200 ft/sec. The specimens were impacted by a steel cylinder whose lower face was parallel to the terminal face of the experimental bit, as shown in Fig. 1. The impacting mass was shifted up and down on two steel rods, dropping from a maximum height of 11 ft, with the velocity varied between 0 and 6.5 m/sec. The initial mass of the cylinder was 4.1 kg, which could be increased by steps up to 8.8 kg by addition of steel plates. The velocity of the steel cylinder was determined by using an electric circuit; as the cylinder dropped, it contacted two steel wires, the first one starting and the second one stopping an electronic counter. Two similar counters connected in parallel were used to corroborate each other. The velocity was checked at each drop as it had been observed to vary somewhat from drop to drop. The two contact wires were located just above the top of the specimen so as to give a value of the instantaneous velocity of the steel cylinder at impact. The distance between the wires was 40 ± 0.5 mm and the discrepancy between the counters was never more than 0.1 m/sec. Thus the velocity was known to within 3.25 per cent. This precision was sufficient with respect to the precision of the machining of the specimens. A very small lack of parallelism between the face of a specimen and that of the impacting hammer resulted in an oblique impact which required a much lower velocity to break the specimen. The experiments had a twofold purpose — (1) to observe the fracture pattern, and (2) to find relationships between the minimum velocity required to generate a fracture within a specimen and the