Search Documents

By W. L. Phillips

Single crystals of aluminum, brass, and copper oriented for (100) and (110) slip were extended at 25°, 400°, and 600°C in simple shear. Aluminum specimens oriented for nonoctahedral slip began to shear at a higher critical resolved shear stress than specimens oriented for octahedral slip. Parabolic stress-strain curves were obtained from zero strain. The initial rate of parabolic hardening was lower for specimens sheared on the (100) plane in a close-packed direction <110>, than for specimens sheared in a nonclose-packed direction <100>. metallographic evidence, however, showed that all slip traces could be explained in terms of (111) <100> slip. All attempts to cause nonoctahedral slip in copper and 70-30 a-brass single crystals were unsuccessful. Instead of shearing, the crystals bent, allowing {111} type planes to come into action. NONOCTAHEDRAL slip in aluminum has been reported under three different conditions: first, as the main mode of slip in tension experiments at elevated temperatures;&apos;-&apos; second, as the main mode of slip in direct shear experiments at room temperat~re; and third, as a minor mode of deformation, i.e., as cross-slip, in tension, shear, and bicrystal experiments at room and elevated temperatures."-l2 However, as far as the author knows, nonoctahedral slip has not been reported in either copper or 70-30 a-brass. The present study was undertaken to determine whether nonoctahedral slip could be obtained in aluminum, brass, or copper at room or elevated temperatures when the shear stress was approximately constant over the cross-section, a maximum at the center, or a maximum at the surface. EXPERIMENTAL PROCEDURE A detailed description of the crystal preparation and shearing apparatus has been given previo~sly. Cylindrical crystals 1/2 in. in diam and 8 in. long were grown from the melt in a temperature-gradient furnace. The aluminum contained 0.001 pct Zn, 0.001 pct S, and 0.001 pct Fe; the 70-30 brass contained 0.015 pct Pb, 0.001 pct Fe, 0.01 pct Ni, 0.02 pct Sn, and 0.005 pct Se; the copper was certified OFHC of 99.98 pct purity. All samples were electropolished prior to testing. The shear apparatus was a modified Bausch type. The strain sensitivity was 4 x lob4 Load was applied by clamping the rods attached to the shear plates in an Instron tensile machine. The rate of loading was 0.02 in. per min. In all cases a 1/8-in. gage length was used. For the tests performed at 400° and 600°C the shear plates, collars, and rods were made of stainless steel. These elevated-temperature tests were performed in an argon atmosphere. A) Aluminum at Room Temperature. Values of a and ß for the various slip planes and slip directions investigated are shown in Table I where a is the complement of the angle between the specimen axis and the slip direction, and ß is the angle between the specimen axis and the normal to the shear plane. The shear stress is a function of a (assuming ß - 0);10 when a is less than 27 deg, the shear stress on the slip plane for which the specimen is oriented has a maximum at the center of the crystal; at a = 27 deg the shear stress is constant across the slip plane; for a greater than 27 deg the shear stress is a minimum at the center. Fig. 1 shows the stress-strain curves for specimens cut from crystals 1, 2, and 5, which were sheared on the (010) plane in the [loll direction at room temperature. These three crystals have shear-stress distributions corresponding to the three dif-

Jan 1, 1962

By R. W. Heckel, R. A. Tanzilli

Treatment of the finite, diffusion-controlled, two-phase, moving-interface homogenization problem has been carried out by numerical methods for a wide range of input parameters. Solutions have been obtained for planar, cylindrical, and spherical diffusion geometries. The effects of parameters such as the interdiffusion coefficients (concentration-independent) of- both phases, the concentrations (time-independent) of each phase at the interlace, mean composition, initial size of the dissolving- phase, and initial composition of- the two phases are considered. The results are displayed to show both the position of the interjace and the degree of homogenization (expressed in terms of concentration at the matrix phase symmetry boundary) as a function of diffusion time. Typical exaw~ples to which the results may be applied are discussed. A limited number of exact, closed-form solutions to the multiphase, diffusion-controlled, moving-interface problem exists in the literature, e.g., Refs. 1 to 7. The exact, closed-form solutions generally consider the outermost phases to be infinite in extent and also assume an interfacial velocity function. It is through use of such boundary conditions that closed-form solutions are readily obtained. An extensive literature also exists on numerical solutions to the mathematically analogous solidification problem, e.g., Refs. 8 to 12. In addition, a numerical solution involving mass transfer with spherical interfaces and infinite boundaries has recently been carried out.13 A practically important class of diffusion problems exists, however, in which the boundaries of each phase away from the interface are finite. For example the finite boundary condition arises when one sets up a model for analyzing the homogenization behavior of two-component powder compacts in two-phase systems or for studying the solution behavior of precipitates. Although exact, closed-form solutions have as yet not been found to this class of problems, solutions are possible using numerical methods. The purpose of this paper is twofold: 1) to describe a numerical method for treating the two-phase, diffusion-controlled, moving-interface problem involving finite boundaries with planar, cylindrical, and spherical interfaces; 2) to present the results of a parametric study which identifies the role played by each variable appearing in the analytical model. R. A. TANZlLLI,Student MemberAIME,onleaveofabsence from the General Electric Co., Re-entry Systems Department and A. W. HECKEL, Member AIME, are Graduate Student in Materials Engineering, and Professor, Department of Metallurgical Engineering, respectively, Drexel Institute of Technology, Philadelphia, Pa. Manuscript submitted May 6. 1968. IMD MATHEMATICAL MODEL The three geometries analyzed are shown in Fig. 1. For each configuration a symmetry element is shown, across whose boundaries the mass transfer is zero. Mean composition, C, and the characteristic solute-rich phase half-thickness (or radius), 1/2, are the independent variables while the characteristic symmetry element half-thickness, L/2 (measured from solute-rich phase center to the matrix phase plane of zero mass transfer), is a dependent variable. The symmetry element for a planar interface accurately represents a real diffusion situation involving the stacking of symmetry elements of constant size. Because cylindrical and spherical symmetry elements of constant size cannot be stacked to fill space, the meaning of the dimension, L/2, for these situations may be considered in terms of the following approximations: and where NA is the number of parallel cylindrical elements per unit area on a surface normal to the cylinder axes and Nv is the number of spherical elements per unit volume. The model consists of a solute-rich phase matrix phase composite of limited mutual solubility. The concentrations at the interface are assumed constant with time; no assumption of local equilibrium at the interface is necessary except for the case where the

Jan 1, 1969

By D. R. Mash

A strong yield point with attendant enhanced mechanical properties was found in commercially pure beryllium under certain conditions of heat treatment. Beryllium specimens also responded to both quench and strain aging treatments. Based on these results, a possible means of obtaining increased normal temperature mechanical properties is suggested. COMMERCIALLY pure beryllium has been found to exhibit the yield point phenomenon and several other aging manifestations under certain conditions of heat treatment. This behavior is not surprising in view of the present accumulation of experience regarding such effects in numerous metals; but in addition to extending this experience to include beryllium, the present study is of interest because aging effects are generally associated with the presence of small amounts of solute elements. The well known lack of tensile ductility in beryllium at normal temperatures is also considered to be due to impurities in some way. In the present investigation, the view was taken that beryllium of commercial purity (greater than 98 pct) should be considered as a dilute alloy and that precipitation phenomena may well exist which could lead to enhanced mechanical properties. In connection with this possibility, published data on the variation of mechanical properties with temperature are of interest. For example, Fig. 1 illustrates the variation of ductility (percentage of elongation) and ultimate strength as a function of temperature for beryllium of various histories.* Although these curves are somewhat schematic in nature, they clearly indicate the possibility that precipitation of an unstable phase and/or aging effects occur during tests in the region 400" to 700°C. The existence of such behavior should be recognized as affecting the properties of the commercial material and perhaps can be employed advantageously. Experimental Method All testing was done at room temperature using a Baldwin universal testing machine. A microformer extensometer was used in conjunction with a micro-former-type stress-strain recorder. All tests were conducted at constant loading rate, the slowest rates being used. This corresponded to 120 lb per min in the 1200 lb full scale range and 300 lb per min in the 6000 lb full scale range. After the rate of loading was set in the elastic range of the material during the early part of the test, no further adjustments were made, allowing the test to proceed at that setting. In the plastic region of the curve above the yield region, strain rates of from 0.002 to 0.006 in. per min were regularly obtained. All experimentation was carried out on specimens machined from the same lot of beryllium, lot No. Y5036BP. Table I shows the chemical analysis as furnished by the supplier, Brush Beryllium Co., as well as the standard specifications to which commercial beryllium is produced. Both 1/4 in. thick hot pressed plate and ½ in. round hot pressed and warm extruded rods were obtained. The history of the material is reported to be as follows: 1—Beryllium metal plates, produced from a standard hot pressed QMV beryllium metal block 4x15x40 in., were cut off and finished machined to 1/4x6x12 in. flat plates. The original hot pressed block was made by hot pressing —200 mesh vacuum cast attri-tioned powder at about 1050°C under vacuum. 2—Beryllium rod was hot pressed and warm extruded. Extrusion billets were machined from the regular hot pressed blocks followed by extrusion at 425°C. The extrusion was done without jacketing, and graphite was used as a lubricant. The rods were then straightened at 720 °C, after which they were annealed at 800°C for 15 min. Both flat tensile specimens and round tensile specimens were tested. The former were machined from the plate stock into standard specimens according to specifications shown in ASTM E8-52T. The nominal cross-section was 0.25x0.500 in. and the gage length was 2 in. The round specimens were

Jan 1, 1956

By Norman L. Newbern, Robert E. Green

An investigation of the effect of size on the deformation properties of metal single crystals made it desirable to grow from the melt cylindrical aluminum single crystals possessing exactly the same crystallographic orientation but varying in diameter. Methods for the growth of rather large (up to 3 in. diam) aluminum single crystals in molds of the desired shape are well known. However, when one applies the same techniques to the growth of smaller (less than 1/8-in. diam) specimens many additional problems arise. Two of the major problems are the construction of the molds to be used and the removal of the thin specimens from these molds without deformation after growth has been completed. Also the problem of the constraint forces exerted by the mold on the specimen is much more pronounced for the smaller specimens. The technique described herein is a zone-melting method in which no mold is used since the surface tension of the molten metal and its oxide is sufficient to retain the melt. The specimen is suspended vertically in a manner similar to that of Keck and Golay.2 However, while Keck and Golay supported the specimen from both ends, the method used here supports the specimen only at the upper end. The surface tension of the molten aluminum and aluminum oxide contains the melt and suspends a length of newly grown crystal that has already passed through the molten zone until the weight of the newly grown crystal is equal to the component of surface tension holding the specimen together in the molten region. When the weight of the newly grown crystal is equal to the component of surface tension holding the specimen together the specimen pulls in two in the molten zone. The length of crystal which can be grown before this separation occurs varies with the diameter of the specimen and the size of the molten zone. In order to prevent the specimen from pulling in two a tube of glycerine is placed beneath the furnace in such a manner that the newly grown crystal passes into the glycerine which provides sufficient buoyancy to allow aluminum single crystals in wire form to be grown to lengths determined only by the length of the tube containing the glycerine. A schematic diagram of the experimental arrangement is shown in Fig. 1. The furnace used is constructed as follows. High-resistance nichrome wire is coiled on a 3/8-in. diam fused quartz tube. The distance between the windings is much less over a length of about 3/8 in. at the center so as to develop a hot spot. This core is located in the center of a 4-in. diam steel cylinder 5 in. in height and insulated from it by Kayolite. The temperature of the furnace is controlled by means of a thermocouple located near the central hot spot and a Minneapolis-Honeywell temperature controller. Temperature ins,ide the furnace is measured with a thermocouple and a standard potentiometer in the usual manner. By the above method it is possible to grow high-purity (99.99 pct Al) aluminum single-crystal wires over a range of sizes. Crystals varying from 1/8 to 1/64-in. diam were grown by the authors. Since the tube containing the glycerine cannot contain a crystal longer than approximately 3 ft, the growth of crystals longer than this presents another problem. It was found that one could cut the newly grown crystal without deformation in the region between furnace and glycerine tube try means of a cutting torch and then by moving the glycerine tube slightly aside continue

Jan 1, 1962

By M. Ahlers, Horace Pops

Slip features and formation of stress-induced mm-tensite have been studied in single crystals of fl phase Cu-Zn alloys in the composition range between 43 and 48 at. pct Zn. A phenomenological analysis is presented in which the glide planes and directions that me associated with the inhomogeneous shear in the martensite phase are predicted from the experimentally determined habit planes and macroscopic shear directions. It is shozun that the resolved shew component of the applied stress on the secondary shew system is a very important factor governing the formation of stress-induced martensite. A comparison is made between martensitic phases that form spontaneously upon cooling and those phases that arise from deformation. THE ß phase in Cu-Zn alloys is unstable and may transform spontaneously by a martensitic transformation1-3 during cooling. Thermoelastic and burst-type spontaneous martensitic phases have been observed3 in the composition range between 38 and 42 at. pct Zn. Martensite forms in alloys containing more than 42 at. pct Zn only by cold work below a temperature denoted as Md.4 Thus, alloys near the equiatomic composition can undergo a stress-induced transformation upon cold work at room temperature. Although data have been obtained concerning the effect of temperature5 and composition4 on the deformation of polycrystalline Cu-Zn alloys, it is rather surprising that few detailed studies6-8 on 6 brass have been conducted for single crystals where the stresses acting on crystallographic planes can be determined. A thorough understanding of transformation mechanisms requires knowledge of the role of stress and plastic strain. With this objective in mind we have made an investigation of the stress-induced rnartensite transformation in single crystals of 0 brass in the composition range between 43 and 48 at. pct Zn. Particular emphasis is given to the morphology and crystallographic features and a comparison is made between stress-induced and spontaneous martensite. I) EXPERIMENTAL PROCEDURE Master alloys having nominal zinc contents of 43, 45, and 48 at. pct were prepared from spectroscop-ically pure metals (>99.999 pct) in sealed quartz tubes under a partial pressure of helium. These alloys were cut into several pieces and converted into small rods by melting in quartz tubes. Subsequently, single crystals were grown from the rods by the Bridgman technique and homogenized for 3 hr at 820°C. Lattice parameter measurements were made from stress- relieved filings. Compositions, as determined from the reported variation of lattice parameter with atomic percent zinc,&apos; indicated a zinc loss of less than approximately 0.25 at. pct. The single crystals were electroturned using a phosphoric acid electrolyte into tensile specimens each with a center section of 1 mm diam and 1 cm gage length. Cylindrical specimens approximately 3 mm in diam and 10 mm long and spark-machined rectangular blocks approximately 3 by 3 by 10 mm were prepared for compression studies. These blocks were stress-relieved and electropolished to eliminate any stresses introduced by spark machining. Crystal orientations were determined to an accuracy of ±2 deg primarily from back-reflection Laue photographs, and sometimes by the rotating single-crystal method. Figs. 1 to 3 show the location of the tension and compression axes within unit stereographic triangles. All specimens were deformed plastically at room temperature using an Instron machine, the crosshead speed being 0.02 or 0.05 cm per min. A hard steel hemisphere was placed at the upper end of the compression samples to achieve uniaxial loading. Trace normals of slip markings and habit planes of strain-induced martensite were determined to an accuracy of ±4 deg from the rectangular blocks by a two-surface analysis and from cylindrical specimens by measuring the angle between the tensile (or compression) axis and the tangent to the surface trace for different rotations about the deformation axis. Slip

Jan 1, 1969

By Robert D. Pehlke, Weldon L. Daines

The reduction of manganese oxide from a basic slag by silicon dissolved in liquid iron at steelmaking temperatures was studied to determine the rate-controlling step for the process. The experiments were carried out under an argon atmosphere in a resistance-heated vertical-tube furnace. The two liquid phases, slag and metal, were held in zirconia crucibles. Sampling and chemical analysis of the slag phase led to time-concentration curves for the system. Results obtained by varying parameters such as temperature, stirring rate, concentration, and melt geometry defined the limiting reaction mechanism. The reduction of manganese oxide by silicon is a fast reaction and reached equilibrium within 90 min. The rate of stirring has a marked effect on the reaction rate, while, on the other hand, the effect of temperature is very small. This identifies the rate-controlling step as diffusion rather than interfaciul chemical reaction. The variation of other parameters revealed that a) diffusion of manganese in the iron phase is the slow step, b) the value of D/6 for manganese in iron at 1550°C is 7x 10-4 cm per sec, c) the energy of activation for the apparent rate constant is 7 kcal per mole, and d) increasing the amount of silicon in the iron decreases the diffusion coefficient of manganese. THE equilibrium relations pertinent to the reduction of manganese oxide from a steelmaking slag by silicon dissolved in liquid iron have been studied, but little is known about the mechanisms that control the rate of the process. The purpose of the present investigation was to study the rate of reduction by silicon and to determine the rate-limiting step. The effects of stirring rate, temperature, composition, and melt geometry were investigated as a means of identifying the controlling step. On the laboratory scale, relatively little work has been done in the area of slag-metal kinetics, primarily because of the problems confronted in attempting to contain liquid slags and metals in laboratory crucibles at steelmaking temperatures. Since graphite is an ideal material for a crucible, several investigations have been carried out on the reduction of various oxides from a slag by carbon in graphite-saturated iron and on the transfer of sulfur between a slag and graphite-saturated iron. Most of this work has been performed in induction furnaces. Studies where the container was not graphite are extremely limited. A single kinetic study of manganese transfer between molten iron and basic slags was carried out by Sano, Shiomi, and Matsushita.&apos; These investigators prepared calcium oxide and titanium oxide crucibles to contain the two-phase system. Only a few experiments were carried out and the results had to be treated qualitatively. Despite the paucity of kinetic data, a large quantity of information is available in the literature concerning the thermodynamics2-12 and physical properties&apos;3-21 of the slags containing manganese oxide and the dilute liquid iron alloys containing manganese and silicon which were involved in this research program. EXPERIMENTAL METHOD A vertical-tube resistance-heated furnace was used in this investigation to study the slag-metal reaction Although most previous slag-metal studies were carried out in induction furnaces, a resistance furnace has several advantages including better control of temperature and stirring rate. Hence, a resistance furnace was selected for this study, and its design is shown schematically in Fig. 1. Slip-cast, fine-grained, low-porosity, lime-stabilized cubic zirconia crucibles were used for the kinetic experiments. The crucibles were 4 1/2 in. high and 2 1/8 in. OD with a 1/16-in. wall. The crucibles were only slightly

Jan 1, 1969

By H. D. Outmans

In steady vertical flow, the interface of an immiscible liquid-liquid displacement is horizontal for any flow rate below the critical. In nonvertical flow, however, the shape of the interface in the steady state does depend on the flow rate, and the purpose of this paper is to calculate the unsteady interfaces during the transition of one steady state of flow to another. A knowledge of these transient interfaces is of considerable importance in reservoir engineering where the calculation of breakthrough recovery depends on the instant the interface reaches the producing wells and on the shape of the interface at that time. Although the emphasis is put on transient interlaces, which eventually approach stable equilibrium, it is shown that if the displacement exceeds a critical rate no equilibrium is possible. The interface is then unstable and viscous fingers are formed during the displacement. The critical rate and the shape of the transient and equilibrium interfaces are affected by the effective interfacial tension; but since this effective interfacial tension appears in the calculations only in combination with the inverse square of the thickness of the medium, its effect in the reservoir would appear to be negligible compared to its significance in model experiments. INTRODUCTION Stability criteria and the early growth of interfacial disturbances in a plane parallel to the boundaries of a dipping formation in which oil is displaced by an incompressible fluid were described in a previous paper.l This type of instability is significant in thin reservoirs. However, if the reservoir has appreciable thickness, then interfacial stability in vertical planes, normal to the upper and lower boundaries, also becomes important (the displacement is supposed to be parallel to these vertical planes). The difference between the two stability problems is that, in the first case, the intersections of the interface with planes parallel to the boundaries are normal to the direction of the displacement; in the second case, the intersections, this time with vertical planes, are not normal to the displacement. Instead, they are tilted at an angle which depends on the displacement rate. The tilt of steady interfaces was calculated by Dietz2 who also determined the critical rate of displacement for stability in the vertical plane by assuming that this rate would coincide with an interfacial tilt equal to the dip of the formation. The critical rate thus calculated is the same as has been found for thin reservoirs (see Eq. 1.1 of Ref. 1 and of the present paper). Dietz&apos;s calculation of the stable tilt was verified by laboratory experiments and the agreement was found to be fairly good.3 It is doubtful, however, that stable tilts actually exist in the reservoir because a change in production rate is not followed by an instantaneous adjustment of the interface to the new rate but, rather, by a transition period during which the interface changes from one equilibrium tilt to the other. The principal objective of this paper has been to describe these transient interfaces without putting any restrictions on the flow conditions or the shape of the interface, as had been done previously. The second objective was to compute the critical velocity, taking into account capillary effects, and the third was to evaluate, at least qualitatively, the shape of the front at rates above the critical, again without making the simplifying assumptions introduced by previous investigators.2,3 In the following sections two examples are given of the calculation of interfacial motion. The first describes this motion for an initially horizontal interface in a dipping layer, and the second for a vertical interface in a horizontal layer. The mathematical formulation of the problem is nonlinear in the boundary conditions, and this prohibits its solution in closed form. Instead, the solution is obtained in the form of higher-order approximations. 1 Before proceeding to a description of the mathematical model, however, we define two quantities

By J. Chipman, N. J. Grant, E. C. Roberts

An equilibrium study was made of the distribution of chromium and oxygen between liquid iron, containing less than 1 pct Cr, and simple slags of the CaO(MgO)-Si02-FeO-Cr& type in the temperature range 1526&apos; to 1734OC. The effects of slag oxidation, temperature, and basicity were observed. IN spite of the fact that chromium is one of the most important alloying elements in steel, and exists in almost all steels as a significant residual element, little research has been done to determine its behavior in basic steelmaking processes. Considerably more work has been done under silica-saturated acid slag conditions. Korber and Oelsen,&apos; Herasymenko,&apos; and others have generally agreed that in acid steelmaking practice the chromium in the slag behaved as if it were present as the chrom-ous ion (CrO). Work by Hilty- ir, high chromium slags also indicated that chromium may exist as CrO. In basic slag systems no equilibrium data exist. Based on individual studies of basic open hearth and electric furnace practice, Bardenheuer," Rock-rohr,% nd HauckQ oncluded that: 1—chromium recovery increased with decreasing basicity, and 2— chromium recovery increased with increasing temperature, although the effect was small. In similar studies Yavioskii and Dzemyen&apos; concluded that: 1— slag FeO is the most important variable, 2—the basicity of the slag has no effect on chromium recovery, and 3—slag viscosity is not high even when 20 pct Cr,O, is present. Lapitskii\ oncluded that chromium recovery improved as the basicity of the slag decreased and increased with increasing manganese in the metal. Regarding the effectiveness of CrZ08 as a base or acid in basic slags, both Kristofferseno and Trojer" reported that Cr,08 was an acidic component requiring neutralization as 2CaO-Cr,O,. Experimental Procedure The experimental apparatus and procedure used for the present research were similar in most details to those used by Winkler and Chipman" and were described in detail by them. A magnesia crucible was used, holding 60 to 80 lb of Armco iron which was decarburized with hydrogen to about 0.010 pct C. Since all the metal samples solidified without gas evolution, this carbon level was assumed not to be significant. Synthetic slags made by mixing pure oxides were used throughout the study. Temperatures were measured by means of calibrated W-Mo thermocouples and were checked by Pt-Pt-Rh thermocouples. The range of temperatures covered in this study was from 1526" to 1734°C. The chromium content of the iron was in the range 0.032 to 0.82 pct, although the bulk of the tests showed 0.04 to 0.2 pct. The slags were of the CaO(MgO)-SiO,-FeO-Cr,O, type in which the Cr,O, content was from about 2 to 20 pct, although most of the slags showed from about 2 to 10 pct. The FeO range was from about 10 to 65 pct. CaO and SiO, were in the range of about 5 to 45 pct each, yielding a rather wide range of basicity values. The first 12 heats were made without a sulphur addition, and with only 30 min allowed for slag-metal equilibrium to be reached. In previous research it had been shown that less than 30 min was adequate to achieve equilibrium in slags free of Cr2O8.11,14.15 A study of the present data indicated that some of the tests may not have reached equilibrium in this time; accordingly four additional heats were made in which at least 1 hr was permitted for equilibrium to be reached. For reaching

Jan 1, 1955

By John L. Walter

A sintered compact of iron containing 0.007 vol fraction of glass , prepared 6). powder rnetullurgtcal lechniques, was rolled lo foil, 0.001 in. /hick. The foil sullrples were anneuled a1 650° to 850°C in hydrogen. Pri,narj recryslullization prodtnced large grains which Lc3ere highly elongnled in the rolling direclion und which had an unusual prgferred orientation. The glass parlicles assumed a stringerlike dispersiorz on working; llie slrinyers were parallel lo the rolling direction and to the long axis of the grains. The same unusual grain structure, preferred orientation, and stringerlike dispersion of purticles are found in heal-ily rolled and annealed foil of tungsten which has heen doped wilh small amounts of aluminum, silicon, and polassiutvt. Both the proper dispersion of the particles and severe working (reductions in excess of 98 pct) are necessary to produce the elongzcted grain structure. RECENTLY, the author reported on the origin of the elongated or "nonsag" grain structure in tungsten foil which was doped with aluminum, silicon, and potassium.&apos; It was observed that particles, identified as mullite (Al6Si2Ol3), were present in the doped ingot (as sintered) and at all stages of processing from ingot to sheet or wire. It was shown that the particles, being plastic at tungsten working temperatures (up to 1550"C), underwent a "stringing out" parallel to the working di-direction. It was concluded that these strings of particles were responsible for the formation of the highly elongated interlocking grains observed in doped tungsten wire or sheet. To give further credence to this explanation of a long-observed but not understood phenomenon, it was decided to design a new system, one which was analogous to the doped-tungsten system. Thus, a bcc metal, iron, was chosen to be doped with glass which would be plastic at reasonable working temperatures for iron. The glass chosen was a #0080 Corning lime glass which melts at about 810°C. This is approximately the same fraction of the melting point of iron (0.6) as the melting temperature of mullite is of tungsten. It will be shown that all the observed unusual features of the doped tungsten are duplicated in the glass. doped iron, even to the preferred orientation of the grains in the recrystallized sheet. In the tungsten sheet the preferred orientation consists of two components, (1i3)(691) and (013)(362), neither of which has been observed as a component in textures of primary recrystallized bcc metals. EXPERIMENTAL PROCEDURE The glass, in the form of fine powder, was added to high-purity electrolytic iron powder and mixed dry. The particular composition chosen was 0.007 vol fraction of glass. After mixing, the powder was mechanically pressed to a disk 0.5 in. diam and 0.15 in. thick at a pressure of 5000 psi. The pellet was sintered, in pure dry hydrogen, for 2 hr at 8 50°C. The sintered pellet was then heated to 750°C and rolled to 50 pct reduction of thickness in two passes, with reheating between passes. The rolling temperature was then reduced to 600°C and the slab was rolled to a thickness of 0.050 in. Rolling to 0.010 in. was accomplished in several passes at 300°C. Final reductions to 0.003 and 0.001 in. were taken at room temperature. This rolling temperature schedule was similar, in terms of the fraction of the melting point, to that used in the rolling of the doped tungsten. The total reduction of thickness was in excess of 99 pct. Samples of the rolled foil were lightly electro-polished and annealed for 1 to 6 hr at temperatures of 650" to 85O°C in hydrogen. Samples for transmission electron microscopy were thinned on a Disa Electropol using AC-1 electrolyte.

Jan 1, 1968

By C. L. Thornburg

FLANKING the Valley of Mexico on the northeast is a mountain range known as the Sierra de Pachuca. This northwesterly-trending range is about 30 miles long and 5 miles wide, its summit attaining an elevation of more than 10,000 feet above sea level, or 2000 feet above the valley floor. Pachuca, a town of 50,000 inhabitants, lies nestled at the southwest base of the range, 60 miles northeast of Mexico City. Three miles to the east, just over the summit and on the northeasterly slope, is the mountain town of Real del Monte with a population of about 20,000. These are the two principal towns in a 40-sq mile area whose yield has brought the district to its high rank among the world&apos;s silver producers. Total production probably exceeds 1.25 billion ounces of silver and 4.5 million ounces of gold. Exploitation by the Spanish was under way by 1530. As the mines were deepened operations became handicapped by the inadequate method of handling water with horse whims and bull skins. To offset this disadvantage a two-mile drainage tunnel was started in 1749 and completed ten years later. John Taylor of London acquired the mines from the third Count of Regla in 1824 and formed the Compania de Real del Monte y Pachuca. Two years later Cornish pumps were brought from England. A Mexican company purchased the British interest in 1848 and within a few years resumed an old project of driving a second, lower three-mile drainage tunnel, completing it in 1857. After American interests acquired control of the property in 1906 operations expanded to an unprecedented scale, despite periods of political strife, unstable prices, labor problems, and a growing burden of taxation. An idea of the scale of operations may be gained from records of the last two decades prior to 1947, the last year for which production information is at hand, during which time production ranged from 1.4 million to 1.1 million tons per year, and the combined development and exploration, exclusive of diamond drilling, amounted to about 18 miles annually. Pachuca differs from Zacatecas and some other Mexican silver vein districts that flourished and declined in earlier centuries in that a substantial part of its total production was made after 1900. While the district&apos;s accelerated activity in this century was largely due to the successful application of the cyanide process to the treatment of the ores, improved pumping methods, and new mechanical equipment, it was at the same time stimulated by the opening up of important new orebodies as a result of active and extensive exploration of the vein system. Some of these orebodies were found on veins which terminate upward far below the surface, and though these particular veins do not crop out, they show relationship with a type of alteration which may be their surface expression. The district has been studied by many able geologists, and a large store of information has been accumulated, much of which is recorded in published as well as private papers. Wall Rocks Extrusive Rocks: The Sierra de Pachuca is a thick accumulation of Tertiary eruptive rocks consisting mainly of flows, breccias, and tuffs. Numerous recognizable volcanic vents within the range itself manifest that the range was built up by material ejected from these vents. The maximum thickness of the volcanic pile is not known, but from deep exploration and from relationship with Mesozoic sediments to the north and east it is inferred that the average thickness in the main part of the district may be at least 6000 ft. The extrusive rocks comprise four general types, which in ascending order of age are: andesite, rhyolite, dacite, and basalt. The veins are confined largely to the andesite, the dominant rock of the region. Characteristically this rock is augite andesite, but it includes comparatively acidic as well as basic layers, the acidic strata being

Jan 1, 1952

By J. J. Hauser, H. C. Theuerer

A cathode sputtering technique is described which elin7inates the need for ultrahigh vacuum in preparing thin films of materials sensitive to gaseous impurities. This technique uses a fraction of the atoms sputtering within an anode container to getter actice gases, such as HzO, Oz, and Nz. The gases alzd gettering metal are deposited on the container walls, thus shielding the coating zone of the system from contamination. The use of the method for preparing superconducting-normal metal couples such as Ph-Cu and Ph-Pt is described, and the properties of the individual and composite films are given and discussed. GETTER sputtering is a method which greatly simplifies the preparation of thin films in cases where composition control is critical. A major difficulty with conventional sputtering and other vacuum-deposition techniques is the contamination of the forming film caused by residual gases, such as H20, CO, Oz, and Nz, in the coating equipment. The difficulty arises from the fact that even when the residual pressure in the system is as low as 1 x 10"6 Torr, with a deposition rate of 10A per sec, there are as many contaminating gas collisions with the substrate as there are with film-forming metallic atoms. It is not surprising, therefore, that with reactive metals, such as tantalum and niobium or with semiconductors, such as silicon and germanium, films with properties far different from the starting materials are obtained. In the case of niobium and tantalum, deposited either by sputtering or vacuum evaporation in systems with reactive gases at pressures of the order of 1 x l0-&apos; Torr, the loss of superconductivity is traceable to interstial oxygen or nitrogen. On the other hand, working in vacuum of the order of 1 x l0-" Torr, Marchand and enema&apos; have shown that superconducting films of tantalum with properties approaching those of bulk material are possible. At this level of gaseous impurities -lo6 metallic atoms arrive at the substrate before a contaminating collision occurs again assuming a deposition rate of 10A per sec. It is evident from the above that any successful vacuum technique requires the elimination of reactive gases from the region of the system where coating is occurring. Getter sputtering accomplishes this using conventional vacuum equipment with residual pressures in the 106 Torr range. In fact? vacuum systems with residual pressures of lo-" Torr are adequate for most purposes. With this method, sputtering is confined within an anode can and, by geometric design, sputtering itself is used to purify the argon at the lower and upper parts of the system by the gettering action of the reactive metal. In consequence, the central region of the system where coating occurs is shielded from gaseous contamination. Getter sputtering is particularly useful for the preparation of alloy and compound films. With this method, if a cathode of homogeneous composition is bombarded with high-energy argon ions, transfer of material to the substrate having the same composition as the cathode will occur. This is true after an initial equilibration time, even though the constituents of the cathode may have different sputtering rates. During equilibration, the surface of the cathode changes composition due to differences in sputtering rate, but mass conservation demands a steady-state condition such that the atoms sputtered from the surface have the same composition as the cathode material from which the surface is generated. GETTER-SPUTTERING APPARATUS The original form2 of the getter-sputtering apparatus is shown in Fig. 1. It consists of a closed nickel or stainless-steel can 4 in. tall and 2-3/8 in. in diameter. Mounted symmetrically from each end

Jan 1, 1965

By S. R. B. Cooke, Y. S. Kim, I. Iwasaki

lron oxides or the gangue minerals of iron ores can be made to float, depending upon the choice of collector. The selectivity of the separation is controlled by the accompanying chemical and operating conditions. In this report the findings on the general flotation characteristics of magnetite are summarized and the results are compared with those obtained for other iron oxides. Depending upon the choice of collector, either the iron oxides or the gangue minerals of iron ores can be made to float, the selectivity of the separation being controlled by the accompanying chemical and operating conditions. The mechanism by which a collector exerts preferential affinity for either group of minerals has been a subject of extended discussion. Previous investigations on the electrokinetic properties and flotation characteristics of hematite,&apos; goethite,2 and quartz3 have demonstrated the electrical nature of the interaction of the collector with these oxide surfaces; anionic collectors are effective on positively charged surfaces and cationic collectors on negatively charged surfaces. Thus, from the differences in the electrokinetic properties of the above-named oxides, a theoretical basis has been provided for their separation by some typical collectors. Examination of the results reported for hematite and goethite shows that their electrokinetic properties and flotation characteristics are remarkably similar. It is of considerable interest, therefore, to examine similar information for magnetite, another common iron oxide, in order to consolidate the flotation characteristics of the three principal minerals of oxide iron ores. Such information is practically significant in the up-grading of both natural and artificial mag- netite produced from taconite, and in the treatment of partially oxidized magnetite ores. Information on maghemite and lepidocrocite, polymorphs of hematite, and goethite, respectively, is also of some theoretical interest in ascertaining the effects of crystal structure and of hydration in the iron oxide group. This article reports the findings on the general flotation characttxistics of magnetite, and compares the results with those obtained for other iron oxides. Experimentally, tlhe surface properties of magnetite were investigated by electrophoresis, and by measurement of the aclsorption of some typical flotation collectors. Its flotation behavior was tested by contact angle measurements and by simple flotation tests using a modified Hallimond tube. The basic information thus gathered was shown to be directly applicable to the interpretation of the results of batch flotation tests made on an artificial mixture of magnetite and quartz. EXPERIMENTAL MATERIALS Magnetite: Magnetite concentrate from Port Henry, N. Y., was further purified by fine crushing and magnetic separaiion, and was used throughout this investigation. For flotation tests the 150/200 mesh fraction was iso1ated and was cleaned by leaching briefly with warn 0.1 N HC1 followed by repeated washing with demineralized water. The final sample analyzed 71.71 pct Fe, 22.37 pct Fe" and 0.47 pct insoluble, and was stored in demineralized water. For e1ectrophoresis and adsorption measurements, the —400 mesh fraction of the magnetite concentrate was ground dry in a pebble mill. The surface area of the ground sample, as determined by the gas permeability method, was 70,000 sq cm per g. Since artificial magnetite has been reported to possess somewhat different physical properties than those of natural magnetite, it also was briefly examined. Preliminary flotation tests on a sample of artificial magnelite, prepared by reducing Brazilian hematite in a C0/CO2 mixture and analyzing 71.94 pct Fe and 23.78 pct Fe&apos;&apos;, gave, however, nearly identical results with those using natural magnetite. It was concluded that artificial magnetite behaves similarly to natural magnetite. Samples which had been magnetically separated showed a tendency to cluster together due to residual

Jan 1, 1962

By N. J. Grant, B. C. Giessen, U. Wolff

With the aid of the splat-cooling technique of rapid quenching, metastable alloy phases based on antimony ad bismuth have been prepared. At room temperature, simple cubic phases were found in the Sb + Au, 56 + Yd, and Sb + Ni systems. Another phase was retained in the Au-Bi system at -190°C; in this systent, a microcrystalline phase and a rhombohedrally distorted phase were also observed. The crystal chemistry of these phases is discussed in terms of their valence electron concentration range. A remarkable five-step Phase sequence was found upon heating and equilibration of certain metastable Au-Bi alloys. USING the splat- cooling technique of rapid quenching from the liquid,&apos; a large number of metastable intermediate alloy phases have been prepared in recent years. Thus, Hume-Rothery phases of the hexagonal type based on the valence electron concentration have been produced in systems where they are missing in equilibrium, e.g., Ag-Ge 1 or AU-Sb. 3 In a comprehensive study of metastable alloys based on tin, simple hexagonal metastable y phases were found, raising the total of stable and metastable y phases from 3 to 13. 4 In the In-Bi system, five new metastable intermediate phases were retained.&apos; In most cases, the new metastable phases have some crystal chemical characteristics in common: a) They have rather simple, elementlike structures with few atoms per unit cell, e.g., y phase,4&apos;5 or the metastable primitive cubic phases in the Ag-Te and and Au-Te systems.= b) Their structures are often related to those of the terminal phases, or to elements that are straddled in their position in the periodic table by the constituent elements; this is the case for metastable ß (In-Bi) with the structure of white ß Sn,&apos; or metastable a (Cd-sn). 4 c) They seem to represent the crystal structures appropriate to certain average group number (AGN) ranges in which no or few single-phase structures exist in equilibrium. These average group number ranges can probably be equated in the case of many elements of the Ba(Zn)-Bs(As) groups with the averaged valence electron concentration. In the present work, the splat-cooling technique has been applied to the alloys of antimony and bismuth. In equilibrium, neither element forms intermediate alloy phases with other B elements from groups Bl(Cu) to B4(Si) that contain more than 66.7 at. pct of Sb or Bi, respectively, e.g., AUSb 2. 7 Thus, antimony- or bismuth-rich phases, which might be closely related to antimony or bismuth, and which would reflect struc- tural changes occurring on alloying with small amounts of addition elements, do not exist. Also, the terminal solubility of antimony and bismuth for all B metals is very small. It was therefore of interest to investigate the influence of enforced, nonequilibrium solid solution of addition elements in antimony and bismuth on their crystal structures. It was found that additions of group B 2-B4 metals act distinctly differently than additions of group T 10 and B1 metals. The latter set of additives will be treated here. EXPERIMENTAL TECHNIQUES Alloy preparation and splat-quenching followed closely the procedures described in Refs. 1, 4, and 5; they consisted of the preparation of master alloys from high-purity starting materials (99.99+ pct) and blast-atomizing of 20-mg quantities onto copper sheets. The resulting approximately 1 to 5 u thick foils were investigated by X-ray diffraction. The cooling rates obtained are of the order of 107 to 10 8 C per set,&apos;" causing solidification to proceed at a rat; of approximately 100 cm per sec.&apos; Powder patterns of the resulting fine-crystalline materials were taken with filtered CuK, radiation. For antimony alloys the substrates were held at room temperature and for bismuth alloys at -190°C both during splat foil deposition and X-ray investigation. Annealing treatments at several

Jan 1, 1969

By B. B. Wood, M. J. Rzasa, E. W. Hough

An apparatus for the determination of fluid-fluid interfacial tension by the pendant drop method has been constructed. The apparatus is refined beyond those previously described in that the samples are introduced into an evacuated windowed cell without contacting air or mercury. Interfacial tension data are reported for the water-methane system between 74 and 280°F and 15 and 15,000 psi. The variation of wettability of the stainless-steel dropper tip with pressure and temperature was observed incidentally to the measurements. INTRODUCTION The most refined previous apparatus --for the determination of fluid-fluid interfacial tension at reservoir conditions was built by Hauser and Michaels.&apos; These authors used the pendant drop method, previously investigated by Andreas, Hauser, and Tucker.&apos; Recently, Fordham3 has made the pendant drop method an absolute one by numerical integration of the differential equation of drop shape. It is necessary to know the difference in density of the two fluids and the acceleration due to gravity in order to evaluate the interfacial tension from measurements of drop dimensions. Contact angle is not involved in the measurements by this method. Some precise tests of the method have been made at atmospheric pressure and 77°F by Douglas," who found agreement with established values to within about 0.1 per cent for water and air, cyclohexane and air, benzene and air, and benzene and water. No values of interfacial tension from the recent pendant drop apparatusJ have been published by Hauser and Michaels. However, values for the water-benzene and water-decane systems are given in Michaels&apos; thesis5 or Dressures from 15 .to 10,000 psi and temperatures from 73 to 268ºF. Some determinations on gas-oil and gas-water systems in the range of 15 to 4,000 psi and 78 to 178°F have been made by Hozott,&apos; by the drop-volume method. The capillary rise method has been used to investigate the interfacial tension in gas-oil systems at 88°F to several thousand psi by Swartz.7 Other determinations in gas-oil systems at pressures under 1,000 psia have been made by Jones: and Beecher and Parkhurst.9 The scarcity of data for pressures above 5.000 psi is apparent. APPARATUS An assembly drawing of the working section of the interfacial tenqion apparatus is given in Fig. 2. &apos;The endanant drop (A) is housed in a pressure chamber having glass windows (B). An agitator (6) is provided. The metal parts of the apparatus coming into contact with the sample are made of AISI: Type 316 steel. Drain grooves are provided around the whdows so that the sample in contact with the O-rings is not returned to the working section when the pressure is reduced. A schematic arrangement of the apparatus is given in Fig. 3. The working section containing the pendant drop (A) is filled by samples from bombs (B) with the aid of the vacuum system (C). The O-ring sealed pistons (D) used to separate the sample from the hydraulic fluid are shown together with the pressure production and measurement system (E). A front view of the apparatus is shown in Fig. 1. Most of the hydraulic system is at the top of the panel. The pump and displacement piston are at the lower right. The Variacs for the air bath heaters. the camera. and the vacuum gauge are a1so visible on the panel. The working section together with a window closure and a drop-forming tip closure are shown in Fig. 9. The carbon arc light source with filter is visible in the upper part of the picture. Two sides of the air bath with the impeller and a part of the convection shield can also be seen. The assembled air bath is shown in Fig. 10.

Jan 1, 1951

By E. W. Hough, B. B. Wood, M. J. Rzasa

An apparatus for the determination of fluid-fluid interfacial tension by the pendant drop method has been constructed. The apparatus is refined beyond those previously described in that the samples are introduced into an evacuated windowed cell without contacting air or mercury. Interfacial tension data are reported for the water-methane system between 74 and 280°F and 15 and 15,000 psi. The variation of wettability of the stainless-steel dropper tip with pressure and temperature was observed incidentally to the measurements. INTRODUCTION The most refined previous apparatus --for the determination of fluid-fluid interfacial tension at reservoir conditions was built by Hauser and Michaels.&apos; These authors used the pendant drop method, previously investigated by Andreas, Hauser, and Tucker.&apos; Recently, Fordham3 has made the pendant drop method an absolute one by numerical integration of the differential equation of drop shape. It is necessary to know the difference in density of the two fluids and the acceleration due to gravity in order to evaluate the interfacial tension from measurements of drop dimensions. Contact angle is not involved in the measurements by this method. Some precise tests of the method have been made at atmospheric pressure and 77°F by Douglas," who found agreement with established values to within about 0.1 per cent for water and air, cyclohexane and air, benzene and air, and benzene and water. No values of interfacial tension from the recent pendant drop apparatusJ have been published by Hauser and Michaels. However, values for the water-benzene and water-decane systems are given in Michaels&apos; thesis5 or Dressures from 15 .to 10,000 psi and temperatures from 73 to 268ºF. Some determinations on gas-oil and gas-water systems in the range of 15 to 4,000 psi and 78 to 178°F have been made by Hozott,&apos; by the drop-volume method. The capillary rise method has been used to investigate the interfacial tension in gas-oil systems at 88°F to several thousand psi by Swartz.7 Other determinations in gas-oil systems at pressures under 1,000 psia have been made by Jones: and Beecher and Parkhurst.9 The scarcity of data for pressures above 5.000 psi is apparent. APPARATUS An assembly drawing of the working section of the interfacial tenqion apparatus is given in Fig. 2. &apos;The endanant drop (A) is housed in a pressure chamber having glass windows (B). An agitator (6) is provided. The metal parts of the apparatus coming into contact with the sample are made of AISI: Type 316 steel. Drain grooves are provided around the whdows so that the sample in contact with the O-rings is not returned to the working section when the pressure is reduced. A schematic arrangement of the apparatus is given in Fig. 3. The working section containing the pendant drop (A) is filled by samples from bombs (B) with the aid of the vacuum system (C). The O-ring sealed pistons (D) used to separate the sample from the hydraulic fluid are shown together with the pressure production and measurement system (E). A front view of the apparatus is shown in Fig. 1. Most of the hydraulic system is at the top of the panel. The pump and displacement piston are at the lower right. The Variacs for the air bath heaters. the camera. and the vacuum gauge are a1so visible on the panel. The working section together with a window closure and a drop-forming tip closure are shown in Fig. 9. The carbon arc light source with filter is visible in the upper part of the picture. Two sides of the air bath with the impeller and a part of the convection shield can also be seen. The assembled air bath is shown in Fig. 10.

Jan 1, 1951

By D.E. Norquist, J. E. Moeller

The results of wear on marked balls, 4, 31/2, 3, and 2 in. diam are given. All balls were forged steel of practically the same chemical analysis and hardness. The results indicate that balls in a given mill for a given length of time will have equal diameter losses, regardless of size. IN order to determine the relative wear rates of several sizes of grinding balls, groups of 4, 31/2, 3, and 2 in. balls were marked individually and were charged, all at the same time, into each of two production mills grinding copper ore. The remainder, and vast majority, of the ball charge consisted of 2 in. diam, and smaller, white, cast iron balls. The original weight of each test ball was determined and recorded. Some of each group of test balls were recovered from the mills periodically, individually reidentified, and reweighed. The test balls were recovered during regular maintenance shutdowns, at approximately thirty-day intervals, so as to avoid disrupting operations. As soon as the weights had been recorded, each marked ball was recharged into the mill from which it had been taken. The test units were mechanically the same and theoretically received equal tonnages of feed. All of the test balls were of forged, alloy steel composition with only slight variations in chemistry that would not be expected to affect the physical properties. All were heat treated in the same manner to produce a high hardness, as equal as possible for all sizes and as uniform as possible from surface to center. Generally speaking, the hardness of the portion worn from the balls during the test ranged from 62 to 65 Rockwell C. The microstructure was, therefore, predominately martensitic. The method of marking the test balls consisted of forming a small, round hole, 3/16 or 1/4 in. diam, into the center of each test ball with a Thomas Metal Master disintegrator, which produces a hole in fully hardened steel without affecting the hardness of the surrounding metal. After the hole was formed, each test ball was individually weighed to the nearest gram and the weight was recorded. The balls were grouped as to size and each group assigned a code letter. The individual balls within the various groups were then assigned a number. A small copper disc was stenciled on one side with the group letter and on the other side with the individual ball number and dropped into the hole in the corresponding test ball. The hole was then plugged with a low-melting-point metal alloy, which could be melted out in boiling water. Half of the test balls in each group were charged into one mill and the other half into another mill, so that all test balls in each mill would be subject to, as nearly as possible, identical conditions for an equal length of time. Previous testing had indicated that the wear rates on balls of different sizes could not be accurately compared if weight loss, or percentage weight loss, were used as a basis for comparison. Fig. 1 is a graphic record of the average weight loss for each size group in mill No. 1, and it becomes readily apparent that the larger balls lose substantially more weight in a given length of time. Fig. 2 is a graphic record of the average percentage weight loss for each size group in mill No. 1, illustrating that the smaller balls definitely lose a greater percentage of their original weight in a given length of time. It was, therefore, decided to convert the actual weights of the test balls to diameter and follow the diameter losses periodically to see if the wear rates

Jan 1, 1951

By D. E. Norquist, J. E. Moeller

The results of wear on marked balls, 4, 31/2, 3, and 2 in. diam are given. All balls were forged steel of practically the same chemical analysis and hardness. The results indicate that balls in a given mill for a given length of time will have equal diameter losses, regardless of size. IN order to determine the relative wear rates of several sizes of grinding balls, groups of 4, 31/2, 3, and 2 in. balls were marked individually and were charged, all at the same time, into each of two production mills grinding copper ore. The remainder, and vast majority, of the ball charge consisted of 2 in. diam, and smaller, white, cast iron balls. The original weight of each test ball was determined and recorded. Some of each group of test balls were recovered from the mills periodically, individually reidentified, and reweighed. The test balls were recovered during regular maintenance shutdowns, at approximately thirty-day intervals, so as to avoid disrupting operations. As soon as the weights had been recorded, each marked ball was recharged into the mill from which it had been taken. The test units were mechanically the same and theoretically received equal tonnages of feed. All of the test balls were of forged, alloy steel composition with only slight variations in chemistry that would not be expected to affect the physical properties. All were heat treated in the same manner to produce a high hardness, as equal as possible for all sizes and as uniform as possible from surface to center. Generally speaking, the hardness of the portion worn from the balls during the test ranged from 62 to 65 Rockwell C. The microstructure was, therefore, predominately martensitic. The method of marking the test balls consisted of forming a small, round hole, 3/16 or 1/4 in. diam, into the center of each test ball with a Thomas Metal Master disintegrator, which produces a hole in fully hardened steel without affecting the hardness of the surrounding metal. After the hole was formed, each test ball was individually weighed to the nearest gram and the weight was recorded. The balls were grouped as to size and each group assigned a code letter. The individual balls within the various groups were then assigned a number. A small copper disc was stenciled on one side with the group letter and on the other side with the individual ball number and dropped into the hole in the corresponding test ball. The hole was then plugged with a low-melting-point metal alloy, which could be melted out in boiling water. Half of the test balls in each group were charged into one mill and the other half into another mill, so that all test balls in each mill would be subject to, as nearly as possible, identical conditions for an equal length of time. Previous testing had indicated that the wear rates on balls of different sizes could not be accurately compared if weight loss, or percentage weight loss, were used as a basis for comparison. Fig. 1 is a graphic record of the average weight loss for each size group in mill No. 1, and it becomes readily apparent that the larger balls lose substantially more weight in a given length of time. Fig. 2 is a graphic record of the average percentage weight loss for each size group in mill No. 1, illustrating that the smaller balls definitely lose a greater percentage of their original weight in a given length of time. It was, therefore, decided to convert the actual weights of the test balls to diameter and follow the diameter losses periodically to see if the wear rates

Jan 1, 1951

By Tasuku Fuwa, John Chipman, David H. Kirkwood

Fe-C-Si alloys in silica crucibles were held at 1600°C in a controlled atmosphere of CO and Co2 and the approach to equilibrium was obsertsed. Results were not of sufficient precision to establish the activity and interaction coefficients. Observations 012 the equilibrium provided an average value for the standard free-energy change which differed by + 1.1 kcal from the earlier accepted value. The C-SL relation at other temperatures is calculated and shown graphically. IN the refining of steel in an acid-lined furnace, it is well known that, unlike in basic refining, a very significant amount of silicon may remain dissolved in the metal even when the carbon content approaches a final endpoint. Further, it is known that the residual silicon increases with increasing temperature. The quantitative relation between silicon and carbon can be calculated for equilibrium conditions from data already available on the Fe-C-O and the Fe-Si-O systems. Such equilibrium calculations could show us approximately the limitations within which the reaction would be expected to operate in practice. In the oxidation of a bath containing both carbon and silicon it is well known that at low temperatures silicon is preferentially oxidized first. It can be shown by calculation that at high temperatures carbon will be oxidized preferentially. It is the purpose of this paper to record direct observations on the Si-C relation by means of experiments carried out in an atmosphere of carbon monoxide for Fe-C-Si alloys contained in silica crucibles. When such a system is brought into equilibrium, at a fixed temperature, the composition of the liquid metal is governed by the following equations: Both K1 and K2 are known with a fair degree of accuracy, and may be calculated from the tabulated In general the percentage of CO2 is extremely small compared to that of CO and in the experiments to be described the partial pressure of the latter was generally only slightly below 1 atm. EXPERIMENTAL METHOD The induction furnace employed was the same as that described by Rist and chipman&apos; and by Fuwa and chipman.2 It was modified slightly in view of the change from alumina to silica crucibles. The small silica crucible was surrounded by a thin susceptor of molybdenum sheet which in turn rested inside a zirconia crucible. Since the zirconia was subject to breakage, it was supported inside an alumina crucible. The charge consisted of 30 to 35 g of electrolytic iron along with the required amounts of refined silicon and graphite to produce a melt of required composition. Purified carbon monoxide and carbon dioxide were passed into the furnace through carefully calibrated flow meters. Two separate and independent series of experiments were carried out. In Series I (D.H.K.) the melt was held in the furnace at 1600°C for periods of time up to 6 hr. Samples were taken at intervals in silica tubes and were analyzed for carbon and silicon. The results of the last one or two samples taken from each experiment and the direction in which equilibrium appeared to be approached are shown in Table I. In Series II (T.F.) the silica crucibles were of less satisfactory strength and the melts were held at 1600° C for periods of only 2 to 4 hr. In heats number 29 to 45 inclusive, the metal was cooled in the furnace and the ingot itself served as a sample for analysis. In heat 46 and all subsequent heats, samples were withdrawn in silica tubes at the termination of the heat, and these samples were analyzed. The results of all of these experiments in which equilibrium appeared to be approached are listed in Table II.

Jan 1, 1965

By M. E. Wadsworth, C. H. Pitt

Nickel corrosion in sulfuric acid solutions at elevated temperatures and oxygen wer-pressures was imestigated. Weight loss was 1inear with time and varied directly with oxygen concentration. Independent variation of the possible active species in solution indicated that the undissociated sulfuric acid molecule plays an important part in the corrosion mechanism. The rate determining step was considered to be the adsorption of oxygen on a site containing adsorbed H2SO4. THE tendency for a metal to go into solution depends on a number of factors some of which are: 1) the position of the metal in the electrochemical series; 2) the type and concentration of corroding species in solution; 3) the concentration of oxygen in solution; 4) the type of film formed at the liquid-metal interface; and 5) the physical state of the metal. The corrosion of a metal in an aqueous solution may be considered to be a heterogeneous reaction that occurs at the liquid-metal interface. The reaction is generally considered to occur as a result of electrochemical potential differences within the system. Little work has been published in the literature concerning the corrosion of pure nickel. A great deal has been publistled dealing with the experimental and theoretical aspects of the over-all corrosion process. Evans,1 Uhlig,&apos; and recently Todt 3 and Tomashoff,4 have published books which review the results of experiments which have been conducted on corrosion, and have developed some of the basic ideas of the more widely accepted theories of corrosion. Friend5 states that. nickel does not readily discharge hydrogen from any of the common nonoxidiz-ing acids and that a supply of some oxidizing agent is necessary for appreciable rates of corrosion. He further notes that at temperatures between atmospheric and close to boiling, corrosion rates tend to vary with concentration, temperature, and aeration in acid concentrations up to 25 pct. Whitman and Russel6 studied the effect of dissolved oxygen on a number of metals in acid solutions and found that oxygen accelerates the rate of corrosion of nickel in sulfuric acid. Flowers and Kelley7 in studying the action of dissolved CO, on electroplated nickel postulated that nickel dissolves as NiHCO3 in the presence of CO, and air. It was found that oxygen was necessary for corrosion to take place and that the rate increased with increasing amounts of oxygen in solution. Flowers and Kelley attributed the oxygen effect to cathodic depolarization. MacGillavry, Rosenbaum, and wensson&apos; determined metal solution potentials of nickel in various electrolytes. They found that nickel has no tendency to corrode in alkaline solutions in the presence or absence of air. In acid solutions in the presence of air, metal solution potential increases in the order of 1/2 v were observed. This increase was attributed to probable chemisorption of oxygen on the nickel surface and the corrosion mechanism suggested was the interaction of H+ ions with the nickel oxide formed at the surface. Delahay9 observed the reduction of oxygen on various metals. A polarograph was used to measure the course of the reaction. With some metals hydrogen peroxide was produced as an intermediate compound. However, nickel was not considered to be a hdrogen peroxide producer. Van Rysselberghe 10,11 and associates attributed the accelerating effect of carbon dioxide on the corrosion process to the presence of percarbonic acid produced in solution reacting with the hydrogen peroxide. The percarbonic acid can be reduced at less negative potentials than hydrogen peroxide and as a result accelerates the reaction. EXPERIMENTAL Since a complete description of the apparatus used can be obtained elsewhere,12&apos;13 no attempt will be made here to describe the equipment other than to note that it consisted essentially of an autoclave unit from which samples could be withdrawn periodically without disturbing the interior state of the autoclave. A titanium autoclave liner was used to protect the autoclave from the solution.

Jan 1, 1961

By S. R. Mitchell, M. C. Fuerstenau, A. M. Gaudin

The two principal attributes of a thickener pulp are its settling rate and the ultimate pulp density of the thickened mud. Testing for evaluation of thickening attributes of a pulp has usually been done batch-wise by placing the pulp in a one-liter glass graduated cylinder and noting the position of the boundary between clear liquor and mud as a function of time. Refinements in testing have included repulping a thickened mud to various dilutions and evaluating the settling rate on these various repulped muds. This is considered to make possible an estimate of the settling rate as a function of pulp density and therefore to pinpoint the slowest settling pulp which ought to be critical from the standpoint of thickener plant design. Finally, tests are sometimes made with model-size continuous thickeners of arbitrary size. In batch tests it is generally accepted that the behavior of a pulp is described by a curve such as the one shown in Fig. 1, in which the position of the boundary between clear liquor and mud (the mudline) is plotted against time. It has also been assumed that the initial settling rate (the slope of the line segment AB) is descriptive of the pulp and independent of the size and shape of the container. Where the settling rate is slower and clearly a function of time (portion CD of the settling curve), it has been assumed that the data are not of much use because of the intrusion of compacting phenomena. The next important datum is the height. PE, which is a measure of the so-called ultimate pulp density. This quantity is assumed to be characteristic of the pulp and independent of the container. When actual data are recorded, results are rarely exactly according to this theory and numerous deviations may be noted. For example, some pulps seem to require an appreciable delay before beginning to settle, as in line AF. This is spoken of as representing the need for an induction time for flocculation. It has seemed desirable to explore thickener data with a more sensitive charting tool than is afforded by the coordinates of Fig. 1. Instead of relating the position of the mudline to time, it has seemed desirable to relate the rate of descent of the mudline to time. This, in effect, amounts to charting the slope of the line in Fig. 1, or the derivative of its ordinates, against the same abscissas. Fig. 2 shows the new chart for the curve ABCDE of Fig. 1. When this new tool was applied to data obtained, for example, with sized clay pulps, astonishing differences appeared. Apparently the traditional tool conceals differences instead of revealing them, whereas the new method emphasizes them. It seems, also, that both charting methods have their uses. In this article attention is focused on the effects of pulp density and container height as they affect the settling behavior of flocculated suspensions of a sized kaolin. The thesis by M. C. Fuerstenau&apos; gives more details than this summary, as well as some information about the effect of other variables. Sized fractions of kaolin were used, supplied through the courtesy of S. C. Lyons of the Georgia Kaolin Co. Large batches were made by agitation in a flotation machine and in a glass jar equipped with a mixer. The settling vessels were 2, 4, and 6-in. diam glass cylinders of various heights. Pulp Dilution: The effects of pulp dilution on sedimentation behavior are shown in Figs. 3, 4, and 5. Fig. 3 shows data on pulps ranging from 2.44 to 16.7 pct solids initial pulp density, flocculated with Separan and charted in the traditional manner. At least two of the lines appear nearly straight in their early sections, but neither of the others does. Each of the curves in this figure includes a region labeled

Jan 1, 1960