Search Documents

By M. J. Pool, J. R. Guadagno

THE relative partial molar heats of solution in liquid tin have been determined for phosphorous, arsenic, and antimony at 750°K. This work was carried out as part of an over-all program to determine the heats of formation of the III-V semiconducting compounds. A differential twin-type liquid tin solution calorimeter was used in the investigation. All three elements are endothermic upon solution in tin. The relative partial molar heats of solution go through a minimum value at arsenic. No concentration dependence of the heat of solution was found in the dilute (0 to 2 at. pct solute) solution range investigated. The measured heat effects and the calculated relative partial molar heats of solution at infinite dilution are listed in Table I along with the relative heat contents of the solutes calculated from the data of kelley.1 All of the values are referred to 750°K even though the calorimeter temperature fluctuated by *1°K during the course of the experiments. In this range of temperature change no variations were found which were outside the experimental error. This would be expected since the partial molar heat of solution is in general a very insensitive function of temperature. The limits of error given in Table I represent the standard deviation from the mean. The reported error estimates only apply to the estimated precision of the data and not the accuracy. Systematic errors could be present which would affect the absolute values given. This is especially true in the case of phosphorous and arsenic where vaporization could occur. If this were true, the experimental values reported here would be too high and the true partial molar heat of solution would be less than that given in Table I. Moreover, the heat-content data could be in error and this would also affect the calculated values. The relative partial molar heat of solution of phosphorous at infinite dilution in liquid tin is given in Table I. This value is based on eight drops at

Jan 1, 1965

By J. Gordon Parr, A. J. Goldak

OgdEN et al.1 and Bumps et al.2 suggested that the solubility of aluminum in a titanium extended to 30 pct.* Sagcl,3 Clark and Terry,4 Anderko et al.,5 Ence and Margolin6 and Saulnier and croutzelles,7 subsequently proposed the existence of an intermetallic compound in the region of 25 pct Al. Although Anderko et al.5 suggested that the structure of this phase, Ti3Al, was of the DO,, (Ni3Sn) type, their conclusion was based only upon the results of a powder photograph that included reflections from ? = 0 to ?= 27° (CuK),some of which were reported to be indistinct. Ence and Margolin,6 referring to a 25 pct alloy (but without indicating whether the figure referred to weight or atomic pct) stated: "The structure of Ti2Al is isomorphous with Ti3Sn DO19, as pointed out by Pietrokowsky". But the point was not proven, because Ence and Margolin did not report values of calculated intensities of Ti2Al with the DO,, structure. In fact, the observed intensities they reported are in poor agreement with the values we calculate for DO19 (see Table I). Saulnier and croutzelle7 concluded, on the basis of electron micrography and microdiffraction studies, that the structure of the 25 pct A1 alloy was ordered hexagonal. Our purpose has been to unequivocally determine the Ti3Al structure. Alloys containing 25 pct Al were prepared from iodide titanium and spectrographic standard aluminum by levitation melting. The levitation chamber was evacuated to 10-6 mm Hg before filling with 99.999 + pct A. After casting, the alloy was chilled to liquid air temperature and crushed to -200 mesh in a percussion mortar. The powder, wrapped in molybdenum foil, was annealed (by induction heating) at 1000 "C for 2 hr in the argon atmosphere of the levitation chamber. No sublimate was seen on the foil or elsewhere, and therefore the assumption is

Jan 1, 1962

By H. R. Hanley

IT is a well-known fact that the solubility of zinc compounds decreases when these compounds are roasted in contact with iron compounds, but descriptions of tests to quantitatively express the fact have not appeared in the literature. Possibly such an expression cannot be uniformly and exactly duplicated by different operators because of the variation in the personal equation. In a general way, however, the reactions between zinc compounds and iron compounds under roasting conditions will show a certain trend with changing conditions and the approximate quantitative expression of this trend appears reasonably well established by experimental work conducted for this purpose. Ferrites and Marmatites The name "ferrite" has been given to the compound of zinc and iron which has the formula Zn0.Fe203. Among the questions pertinent to this subject are those involving inherent or natural ferrite, and also the synthetic or artificial variety. The inherent or natural product is formed when the mineral containing iron and zinc sulfides isomorphously crystallized is subjected to oxidation at roasting temperature. These isomorphously crystallized minerals are known, mineralogically, as marmatites, and contain ZnS and FeS in ratios of 2 to 1 up to 5 to 1 respectively. The zinc and iron sulfides form a definite mineral. They are firmly attached to each other and form common contact planes through which diffusion of the entities occurs during the roasting process. This diffusion of the molecularly intimate entities produces, during roasting, the compound referred to as ferrite, in proportion to the amount of iron originally present in the marmatite. For example, a marmatite from British Columbia containing 9.739 per cent. Fe and 56.87 per cent. Zn corresponds with the mineral having the formula 5ZnS.FeS. The ferrite produced in roasting, which has the formula ZnO.Fe203, contains 27.07 per cent. Zn and 46.40

Jan 1, 1929

By S. P. Burke

OUTBURSTS in coal mines have contributed greatly to the hazard of mining operations in localities in which they occur. They have been responsible for many casualties and fatalities and much property damage. An excellent review and symposium on the subject appeared recently1. From a study of the papers included in this symposium, and other litera-ture on this subject2, the following conclusions or statements seem justified: 1. Outbursts are more likely to occur in deep mines; that is, where the coal seam being mined has considerable overburden. 2. Outbursts usually occur when hard, dense, nonfractured coal is being mined. It is believed that in most cases a fault or a pocket of friable or soft or pulverized coal existed some distance behind the dense coal at the time of the outburst. 3. The outburst involves a rending or pushing of the solid material of the coal face, the roof, or the floor outwards and often is accompanied by the discharge of large quantities of very fine coal. 4. Drill holes or borings into the coal ahead of the workings have failed to yield information either from evidence of increased gas pressure or increased gas flow that makes possible the prediction of outbursts. 5. Mines in which outbursts occur are usually considered "nongassy," or only very slightly "gassy"; yet large volumes of gas may be produced at the time of the outburst. Despite the varied conditions and varied locations in which outbursts have occurred, the foregoing general statements appear to be applicable in whole or in part to all the recorded cases. These observations there-fore should be significant and any explanation of the mechanism of the phenomena should be consistent with them. The following suggestion seems to be in accord with this requirement, and is offered in the hope that it may assist in the further elucidation of this phenomenon.

Jan 1, 1935

By John P. Goheen

Considerable work has been done in developing a pyrometer to measure the temperature of molten brasses, bronzes, and aluminum in the crucible. On account of the high melting points and the amount of zinc and sulfurous fumes given off from molten brasses, the conditions are somewhat severe for a thermocouple of standard design; but satisfactory results are obtained with a portable pyrometer, 3 ft. (0.9 m.) of connecting lead wire, and a special 5-ft. nickel-nickel chromium thermocouple, composed of rods 1/4in. (6.35 mm.) in diameter. The lower 12 or 24 in., as desired, may be made detachable so that new tips may be connected at little trouble or expense. The portable instrument need not be of the extreme high-resistance type, as the movable parts of the galvanometer of a lower resistance instrument may be better constxucted to withstand the continuous handling such an instrument receives. Platinum-platinum rhodium thermocouples, protected with porcelain and graphite tubes, have been used, but the lag in registering the temperature is too great. It has been found that the range of temperature for various brasses is as follows: Red brasses...............2200-2250" F. (1205-1234" C.) Yellow brasses............2250-2400" F. (1234-1318' C.) Bronzes..................2300-2550" F. (1260-1400" C.) A recent test with a portable pyrometer having a range of 2600" F. with a bare 1/4 in. heavy exposed couple 5 it. long and a handle attached at the upper end showed that the temperatures of molten aluminum under varying conditions in an oil-fired crucible furnace and one of the Simplex type were as follows: CRUCIBLE, OIL-FIRED FURNACE SIMPLEX FURNACE Temperature of metal in furnace....... 1540" F. (837" C.) 1530" F. (834" C.) Temperature in ladle after skimming at furnace......................... 1480" F. (805" C.) 1440" F. (784" C.) Temperature in ladle after skimming at floor near mold................... 1440" F. (784" C.) 1430' F. (778" C.)

Jan 1, 1923

By J. Gordon Parr, L. P. Srivastava

DUWEZ1 has shown that pure titanium and pure zirconium transform martensitically during rapid cooling at temperatures about 30° and 15°C re spectively below their To temperatures. Holden et al.2 determined M, temperatures of Ti-Cu alloys by a metallographic technique applied to isothermally treated samples. Their results, superposed on the McQuillan3 version of the partial Ti-Cu diagram are shown in Fig. 1. Sources of metals were: Titanium: Iodide bar; Foote Mineral Co. Ltd. Zirconium: Iodide bar; Foote Mineral Co. LM. Copper: Spectrographic Standard; Johnson Matthey and Co. Ltd. Alloys were prepared by levitation melting under argon to the following nominal compositions:* 0.5, Quenching, at rates to about 8000°C per sec, was performed by cooling in a stream of helium (99.999 pct pure) a 3/64 in. cube of material previously heated by a tungsten coil in a system operating at. 10-5 mm Hg. Cooling rates below 200°C per sec w were obtained by controlling the current to the heater coil. The specimen was supported on a 32 gage Pt, Pt-Rh thermocouple attached through a DC amplifier to an Edin magnetic oscillograph (Model 8082) with a maximum chart speed of 250 mm per sec. Transformation temperatures were read off the oscillograph charts at the location of the beginning of the thermal arrest. The same specimen was quenched several times, and all runs were repeated on new samples. Regular calibrations of the oscillograph against a potentiometer were made between quenching experiments. The criterion of martensite formation was the effect of surface rumpling. Previously polished samples that showed a rumpled surface after transformation are assumed to have undergone martens itic transformation: transformations of a diffusion type produce no surface disturbance, Figs. 2 and 3. Electrochemical measurements were made in a cell described elsewhere4 whose electrodes were the martensitic and the diffusion-transformed materials in the following electrolytes:

Jan 1, 1962

By John P. Goheen

Considerable work has been done in developing a pyrometer to measure the temperature of molten brasses, bronzes, and aluminum in the crucible. On account of the high melting points and the amount of zinc and sulfurous fumes given off from molten brasses, the conditions are somewhat severe for a thermocouple of standard design; but satisfactory results are obtained with a portable pyrometer, 3 ft. (0.9 m.) of connecting lead wire, and a special 5-ft. nickel-nickel chromium thermocouple, composed of rods 1/4in. (6.35 mm.) in diameter. The lower 12 or 24 in., as desired, may be made detachable so that new tips may be connected at little trouble or expense. The portable instrument need not be of the extreme high-resistance type, as the movable parts of the galvanometer of a lower resistance instrument may be better constxucted to withstand the continuous handling such an instrument receives. Platinum-platinum rhodium thermocouples, protected with porcelain and graphite tubes, have been used, but the lag in registering the temperature is too great. It has been found that the range of temperature for various brasses is as follows: Red brasses...............2200-2250" F. (1205-1234" C.) Yellow brasses............2250-2400" F. (1234-1318' C.) Bronzes..................2300-2550" F. (1260-1400" C.) A recent test with a portable pyrometer having a range of 2600" F. with a bare 1/4 in. heavy exposed couple 5 it. long and a handle attached at the upper end showed that the temperatures of molten aluminum under varying conditions in an oil-fired crucible furnace and one of the Simplex type were as follows: CRUCIBLE, OIL-FIRED FURNACE SIMPLEX FURNACE Temperature of metal in furnace....... 1540" F. (837" C.) 1530" F. (834" C.) Temperature in ladle after skimming at furnace......................... 1480" F. (805" C.) 1440" F. (784" C.) Temperature in ladle after skimming at floor near mold................... 1440" F. (784" C.) 1430' F. (778" C.)

Jan 1, 1923

By John A. Mathews

It is twenty years since the writer made his first molybdenum steels and others were making them commercially five years earlier but the prevailing opinion seems to be that molybdenum steels are new; from time to time the daily press speaks of important discoveries in Europe and intimates that American steel makers have much to learn in regard to alloy steels. The earlier experiments were largely confined to the use of relatively high percentages of molybdenum in tool steels and permanent magnet steels. Recent developments deal with the types of alloy structural steels used for airplane, automobile, and other engineering requirements; in these, the molybdenum content is usually less than 1 per cent. The earlier types generally have been unsuccessful commercially, but the newer types of steels are becoming of increasing importance. The war showed our dependence on foreign sources for alloying metals; molybdenum alone is widely distributed in the United States and seemingly abundant. Many deposits are not now of commercial interest, owing to location and relatively small amount of ore available, but other deposits are being developed and a stable source of supply seems well assured. In tool and magnet steels, it was early found that 1 part of molybdenum was equivalent to from 2 to 2.5 parts of tungsten. The permanent magnet steels investigated by Madame Curie,' in 1898, contained from 3.36 to 4.05 per cent. molybdenum; in 1902, Dr. E. L. French and the writer thoroughly tested steels containing from 2.0 to 4.0 per cent. These steels gave satisfactory tests for permanence, but were low in residual density and much more sensitive to hardening than the corresponding tungsten products. We discontinued work with them, therefore, and have no advice that such steels have been used commercially here or abroad. Prior to the development of the Taylor-White process and the modern high-speed steels, air-hardening steels were in general use. These were

Jan 1, 1922

By Norman Maxwell

There was more activity in crude production in northwestern Pennsylvania in 1935 than for several years before, resulting in an increased oil production and also in the number of wells completed. Crude -production approximated 16 million barrels for the state, an increase of about one million barrels over 1934. Demand, indicated by refiners' runs to stills, increased proportionally, leaving stocks of available crude at the end of the year at the lowest point since the middle of 1934, when they reached an all-time low. The price of crude varied during the year from a low of $2.02 to a high of $2.27 at the end of the year for Middle district oil. The price of Bradford and southwest Pcnnsylvania oil changed accordingly. The average for the year would be a lower price than in 1934. A summary of the production data for the year 1935 is given in Table 1. In making up this table, 1935 figures were simply added to the table published by S. H. Cathcart last year1. A list of important wildcats is given in Table 2. Bradford Field Approximately 10,000 acres of the proven producing area of the Bradford field is in Cattaraugus County, New York, and it is possible, by differences, to distinguish the Pennsylvania production from the New York portion. The listed production for the Bradford field includes only that portion of the field situated in Pennsylvania, but also includes production from a small pool, locally known as the Mt. Jewett-Kanesholm pool, where the Bradford sand is being developed and flooded in precisply the same manner as that of the Bradford field itself. The Mt. Jewett-Kanesholm pool is not, strictly speaking, an extension of the Bradford field, but inasmuch as it is so closely allied with the Bradford field-—that is, the sand is the same and the production methods are the same—the production and drilling figures include this area.

Jan 1, 1936

By G. S. Brooks

DURING the past few years, the Mineral Point Zinc Co. has had under consideration the improvement of various types of gas-filtering apparatus used in the removal of dust from crushing and milling plants, in the manufacture of oxide, and on blast-furnace fume and sintering furnaces. The original equipment of the various plants of the company was, of course, along lines of the standard stationary bag house. These houses required large surfaces, hand shaking, and varied only in the manner of the collection of solids and in the distribution of the gas. Early in 1908, the first trial of a mechanical bag house was made at Nassau Plant at Depue, Ill. The duty of this installation was on dust-laden gas from a fine-crushing mill. The Printz and Rau bag machine was finally adopted and put into operation. This ingenious machine embodied what were then to us two novel features in bag-house practice: 1. An intermittent crinkling and snapping of the filtering fabric to free the meshes of solids. i 2. A reversal of gas flow for a short period by a temporary connection w th the suction trunk. This equipment worked fairly well except in cold weather, when we ran into condensation troubles. Had we at that time understood more fully some of the limitations of fabric filtering work, these might well have been remedied. We were impressed by this experience, however, with the efficiency of sudden tension on the fabric under suction. After a study had been made of some of the Western blast-furnace houses using the reversal-of-flow feature, experiments were started early in 1914 with a view to developing an automatic equipment along the best lines of our past experience. The objects sought were: 1. Keeping labor out of the houses for hygienic reasons. 2. Reduction of labor costs. 3. Reduction in -size of hag houses. 4. Accessibility. 5. Ability to handle relatively hot gases where required.

Jan 11, 1917

By John A. Mathews

It is twenty years since the writer made his first molybdenum steels and others were making them commercially five years earlier but the prevailing opinion seems to be that molybdenum steels are new; from time to time the daily press speaks of important discoveries in Europe and intimates that American steel makers have much to learn in regard to alloy steels. The earlier experiments were largely confined to the use of relatively high percentages of molybdenum in tool steels and permanent magnet steels. Recent developments deal with the types of alloy structural steels used for airplane, automobile, and other engineering requirements; in these, the molybdenum content is usually less than 1 per cent. The earlier types generally have been unsuccessful commercially, but the newer types of steels are becoming of increasing importance. The war showed our dependence on foreign sources for alloying metals; molybdenum alone is widely distributed in the United States and seemingly abundant. Many deposits are not now of commercial interest, owing to location and relatively small amount of ore available, but other deposits are being developed and a stable source of supply seems well assured. In tool and magnet steels, it was early found that 1 part of molybdenum was equivalent to from 2 to 2.5 parts of tungsten. The permanent magnet steels investigated by Madame Curie,' in 1898, contained from 3.36 to 4.05 per cent. molybdenum; in 1902, Dr. E. L. French and the writer thoroughly tested steels containing from 2.0 to 4.0 per cent. These steels gave satisfactory tests for permanence, but were low in residual density and much more sensitive to hardening than the corresponding tungsten products. We discontinued work with them, therefore, and have no advice that such steels have been used commercially here or abroad. Prior to the development of the Taylor-White process and the modern high-speed steels, air-hardening steels were in general use. These were

Jan 1, 1922

By Norman Maxwell

There was more activity in crude production in northwestern Pennsylvania in 1935 than for several years before, resulting in an increased oil production and also in the number of wells completed. Crude -production approximated 16 million barrels for the state, an increase of about one million barrels over 1934. Demand, indicated by refiners' runs to stills, increased proportionally, leaving stocks of available crude at the end of the year at the lowest point since the middle of 1934, when they reached an all-time low. The price of crude varied during the year from a low of $2.02 to a high of $2.27 at the end of the year for Middle district oil. The price of Bradford and southwest Pcnnsylvania oil changed accordingly. The average for the year would be a lower price than in 1934. A summary of the production data for the year 1935 is given in Table 1. In making up this table, 1935 figures were simply added to the table published by S. H. Cathcart last year1. A list of important wildcats is given in Table 2. Bradford Field Approximately 10,000 acres of the proven producing area of the Bradford field is in Cattaraugus County, New York, and it is possible, by differences, to distinguish the Pennsylvania production from the New York portion. The listed production for the Bradford field includes only that portion of the field situated in Pennsylvania, but also includes production from a small pool, locally known as the Mt. Jewett-Kanesholm pool, where the Bradford sand is being developed and flooded in precisply the same manner as that of the Bradford field itself. The Mt. Jewett-Kanesholm pool is not, strictly speaking, an extension of the Bradford field, but inasmuch as it is so closely allied with the Bradford field-—that is, the sand is the same and the production methods are the same—the production and drilling figures include this area.

Jan 1, 1936

By T. M. Chance

THE necessity of adopting improved methods of bituminous-coal cleaning at. many collieries is recognized by all familiar with the requirements of the various bituminous markets, the approaching exhaustion of the relatively small areas of inherently high-grade-coal, and the difficulties encountered in maintaining a uniform grade of shipped coal. Many coals lose much of their .market value by degradation in size, and, in any event, if the cleaning process is to contemplate wetting the coal the minimum amount of fines should be produced to prevent sludge losses and the difficulties resulting from the moisture content of the wet fines. Hence, it is desirable to by-pass the finer coal dry, if this can be done without too-great increase in impurities in the final product. This procedure has given excellent results at washeries at Steelton and in the Birmingham district. If the raw fines are too impure to permit admixture with the washed coal, it may be desirable to use dry methods, such as the pneumatic table, rather than to wet an excessive amount of such fine material. The bituminous-coal cleaning plant should therefore: (1) Treat the raw coal in as large lump as possible and without sizing; (2) eliminate degradation of pure coal -in the washing process; (3) avoid wetting the fines, if possible; (4) produce washed coal practically free from mechanically included impurities; (5) crush the refuse and retreat, if much intergrown coal, and refuse are present, rather than precrush the entire feed. Ordinary gravimetric methods of concentration, whether hydraulic or pneumatic, will not meet all of these requirements, as the large lump includes those sizes. now sent to the picking tables, if it is desired to treat material of such size. I do not know of any prior commercial method, based on the falling velocity, coefficient of friction or resistance to fracture, that permits the production of clean coal varying in size from, say, 10-in. lump to 1/16 -in. mesh.

Jan 6, 1924

By A. T. Peters

DURING an investigation concerning the use of large nozzles for pouring of low-carbon rimming steels, the practical details of which were reported elsewhere, it was noticed that increases of nozzle sizes were generally followed by improvements of slab surface quality. It is the purpose of this note to present the data available and some tentative opinions about this phenomenon. The problem of correlating pouring rates with the metallurgical performance of steels is complicated by several factors. The two most important are; 1) Variations of the steel pouring rate throughout a pour, these being due to the nozzle erosion, which enlarges the bore area, and the dropping ferrostatic pressure in the ladle. The pouring rate is lowest towards the end of a heat when the ladle is nearly empty. 2) Variations in the ingot pouring time due to the different ingot weights poured. Consequently, the use of the average pouring rate of a heat may not be exact, but in large-scale production it is not practical to treat ingots separately according to their pouring rates. The variations of ingot weights and sizes may be overcome by considering the rate of rise of steel in the mold. Hence, the average rate of filling of molds throughout the pour of a heat, inches per second, will be used in this note. Every ingot rolled at Inland is rated at the blooming mills prior to hot machine scarfing as being good, fair, or poor for cracks, scabs, and checking. The latter term refers to the network of breaks or lines associated with overheating or burning in the soaking pits. It is also known that thin-skinned steel is prone to show this defect if the subsurface blowholes are exposed during reheating or rolling. The experiences with the surface quality of slabs rolled from ingots poured at different rates are presented in Fig. 1. The data represent nearly 11,000 ingots. It appears that all three types of defects are in-

Jan 1, 1960

By S. Paul Lindau

THREE years ago it was decided by the management to granulate the matte that is produced in the smelter of the St: Joseph Lead Co. at Herculaneum, Mo., thereby doing away with a large amount of labor in handling the matte and in subsequent crushing. On Mar. 1, 1915, the granulator was put in operation and up to Jan. 1, 1916, 18,735 tons had been, granulated. The four blast furnaces have a daily output of about 280 tons of pig lead and 100 tons of matte assaying about 11.0 per cent. Pb. It is expected that projected improvements in roasting methods will eliminate more sulphur from the charge, and cut down the matte-fall, to about one-half of the present figure. The blast furnaces are tapped into movable forehearths or settlers, 6 ft. by 4 ft. by 22 in., the slag overflowing into 27-cu. ft. slag cars which are hauled to the clump by electric locomotives. Previous to the adoption of granulation, the matte was tapped from the forehearths into small slag pots which were dumped after cooling. The matte cakes were broken with sledges, and transported to the crushing plant for fine crushing and screening. Here the matte was reduced to ¼ -in. size before being fed to the roaster bins.. A Wedge and a Holthoff mechanical furnace are used for preroasting before sintering on the Dwight and Lloyd machines. The matte is returned to the furnaces as an iron flux until the .gradually accumulating copper content reaches about 7 per cent., after which it is put aside to be concentrated in a small copper blast furnace, the resultant high-grade matte-being sold. When the matte does not settle readily from the slag, two settling devices are often used, the second one being a large catch-pot, which gathers any matte that may overflow from the forehearth, the slag then overflowing from the catch-pot into the slag cars. When full of matte, the catch-pot is removed, allowed to cool, and the contents broken and crushed.

Jan 10, 1916

By Eugene A. Stephenson, Leon J. Pepperberg

The natural gas industry is essentially a byproduct of the oil industry. When first discovered the gas was usually regarded as a nuisance, and even when found immediately associated with oil, or suspected to be so, it was customary to blow it freely into the air, in the hope that gas would shortly be replaced by a flow of oil. The early methods of production,' transportation, and utilization were neither economical nor efficient; the chief value of gas was based on its use as a fuel, with no regard to (1) its effect. upon the oil with which it was associated, (2) its importance as a lifting agent, or (3) to its possibilities for the manufacture of byproducts. The spread of scientific research among major gas and oil companies, manufacturers, and academic groups, has gradually brought recognition of the fact that many of the technical problems bearing on production, transportation and utilization are common to both the gas and the oil industry. A few of the problems that have received serious study, and from which highly gratifying results have been obtained, are: (1) gas measurement, (2) oil well and gas well capacity tests, (3) elimination of field waste, (4) design of pipe lines and compressor stations, (5) extraction of constituents which might interfere with the normal flow of gas through the line, (6) control of reservoir pressure, (7) estimation of reserves of both oil and gas, (8) control of water encroachment, (9) measurement of factors which influence fluid movement through sands, (10) solubility of gases in oils, (11) effect of dissolved gases upon the properties of the solution. These investigations have demonstrated that almost every problem relating to oil production also involves some phase of natural gas engineering. During the past 15 years the use of experimental methods for the discovery and measurement of obscure, influencing factors, which cannot be determined purely by hydrodynamic or thermodynamic analyses, have contributed much towards the progress made in solving the problems of the oil and gas industries. Most of the experimental work on

Jan 1, 1934

By F. Cadena

HIWASSEE Dam, now under construction by the Tennessee Valley Authority on the Hiwassee River, a tributary of the Tennessee River, will require aggregate for approximately 800,000 cu. yd. of concrete. Near the damsite deposits of natural sand or gravel are not available and graywacke, a rock that is found in abundance, suggested itself as a likely source of manufactured aggregate. Graywacke is a metamorphosed sandstone composed principally of a mixture of quartz (65 per cent), mica (25 per cent), and feldspar (10 per cent). Other minerals are present in negligible amounts. The rock varies in different parts of the quarry from very fine to a coarse grain containing particles of about 1/4 in. maximum size, although the bulk of the deposit is medium grain. Extensive tests showed that graywacke would be suitable as a source of both coarse and fine aggregates. The aggregate plant available for use at Hiwassee Dam consisted of the coarse-aggregate and sand plant used on the Norris project. The coarse-aggregate plant had also been used at Chickamauga Dam. Although most of this plant equipment is now in use at Hiwassee, the present flowsheet is not only different from that at Norris and Chickamauga but is also unique as compared to the flowsheet of the average crushed-stone aggregate plant. It is hoped that this paper will show the importance of proper arrangement of equipment if the optimum in flexibility and capacity is to be attained. FLOWSHEET Rock is loaded by 3-yd. electric shovels into 12-yd. dump trucks, which carry the rock to the primary crusher, a 42-in. Superior McCully gyratory unit set at 4 ¾ in. (Fig. 1). The primary crusher discharges directly onto a 42-in. inclined belt conveyor, which carries the product to a surge storage pile with a maximum live storage capacity of approximately 3000 tons. A concrete tunnel under this storage pile houses the feed end of a 36-in. belt conveyor (conveyor B) fed by a 36 by 66-in.

Jan 1, 1939

By Frederick Crabtree

WHEN Professor Stock asked for a paper on the above subject, it was too late to prepare by June 1, or near that time, one that would involve any appreciable amount of experimental work or original research; but the suggestion was made that a review of the literature bearing on the subject might be submitted in good time, and that later this could be supplemented by any experimental data obtained during the summer, if experiments were carried out. In accordance with this suggestion, there are submitted the following notes on references found in the literature of recent years bearing on sulfur in gas. It is to be, understood that, ill general, these notes express the opinions of the authors whose papers are abstracted, not necessarily the opinions of the abstractors. Very little published information was found bearing directly on producer-gas sulfur, so this has been supplemented, in certain phases of the subject, by references to illuminating gas. Methods of analysis and processes for the elimination of sulfur from the gas are, without much doubt, very closely related in these two products. As in illuminating gas, sulfur is found in producer gas mainly as hydrogen sulfide, mixed with a much smaller and variable quantity of carbon bisulfide.1 The presence of minute quantities of other organic-sulfur compounds has been intimated, but no definite statement is made concerning these. The amount of sulfur present in producer gas is variable and depends on several conditions. The primary factor is the quantity of sulfur in the fuel, but the form in which the sulfur exists, the temperature of the producer, the air-steam ratio, and the efficiency of the scrubbing process are all determining factors. When the coal used contains less than 0.5 per cent. of sulfur, the sulfur in the gas will not exceed the quantity found in the average illuminating gas.2 Sulfur in producer gas may safely

Jan 9, 1919

By S. Skowronski

The melting of cathode copper, ususally containing 95.98+ per cent. • Cu, would appear to be a simple matter. Owing to the well known affinity of copper for sulfur, however, so much sulfur is absorbed by the copper during the operation that a long and expensive refining process is required to remove it, and the final product is inferior in purity and lower in electrical conductivity than the original cathode copper. The furnace operation, as now conducted, includes the following stages: 1. Charging the cathodes into the furnace. 2. Melting the cathodes. 3. Oxidizing period—saturating the copper with cuprous sub-oxide and bringing the metal to the condition known as "set copper;'' this is now done by blowing air into the molten bath of metal. 4. Reduction period, otherwise known as "poling," whereby the oxygen previously added is removed by covering the molten bath completely with coke or charcoal and introducing large poles of green wood; this reduces the cuprous sub-oxide, bringing the copper to the "tough pitch" stage ready for casting. 5. Casting Period. Many experiments have been made to obviate the long periods of oxidation and subsequent reduction, with no success. While the copper first cast will be good, as indicated by the set surface of the bars, it is impossible to hold it to the "tough pitch" condition, and long before the whole charge has been poured the copper will become "overpoled," entailing numerous difficulties. Sulfur has always been blamed by the furnace men as the reason why this refining process is necessary, yet the literature on the subject does not sufficiently emphasize how small a proportion of sulfur will ruin copper for practical purposes. The sulfur absorbed by copper during the melting period comes from two sources: (1) the sulfate left on the cathode sheets in the tank houses; (2) the fuel. The percentage of sulfates on the cathodes is variable, and depends on the care taken in washing the cathodes after removing

Jan 1, 1919

By W. P. Frey

THE briquet plant of the Lehigh Coal and Navigation Co., at Lansford, Pa., has previously been referred to.1 It has passed. the stage of experiment and now rests,, on a foundation practically and financially sound. The purpose of this paper is to explain how success has been attained, and to set standards for the development of hard-coal briquetting which may eliminate future failures. All the conclusions are based on actual results, avoiding speculation and theory. Up to three years ago, the L. C. & N. Co. used coal-tar pitch as a binder in making hard-coal briquets. The plant operated with a monthly output of 300 to 600 tons and was unable to meet its own expenses. Naturally, no one was satisfied, especially as the ideals of a smokeless briquet were still unrealized. Then came the Dutch oil process, introduced in this country by the General Briquetting Co. of New York. This process uses as binder a small percentage of heavy residue of petroleum, which, being liquid, permits great economy of handling; it also did away with the most objectionable fumes of the former briquets. This oil2 is not absolutely smokeless; heating the fresh fuel to red heat liberates some low-volatile hydrocarbons, yielding a white smoke which is not objectionable. On the other hand, this oil adds to the briquet about 7 per cent. of volatile matter, giving the product a heating capacity equal to that of the best free-burning anthracite coal. The average silt used in the manufacture of these boulets averages 16.5 per cent. chemical ash, corresponding to 12,000 B.t.u. per pound of coal. The Hydrolene used as binder runs about 17,500 B.t.u. per pound, and approximately 7 per cent. of it enters into the mixture, hence 12,000 X 0.93 11,160 B.t.u. 17,500 X 0.07 1,125 B.t.u. Total 12,355 B.t.u. per pound of briquets

Jan 1, 1918